Search Documents

By David P. Hale

The Cartersville barite district is near Cartersville, Ga., in the southeastern part of Bartow County, about 43 miles northeast of Atlanta. The area over which active mining is being done extends about six miles in a northeasterly direction and is about three miles wide. Barite production in Georgia began about 1907,' but the existence of the mineral was known much earlier. At present four companies are operating washing plants and three other plants are operating on leases from those companies. The chief impurities in the ores are silica and iron oxide. The silica is easily washed and jigged out and gives little trouble. Any gravity separation between the iron and the barite is generally poor, owing to the slight difference in specific gravity. Two operators have turned to magnetic separation as the solution to the problem and have made remarkable improvements in the finished product. By very close sizing prior to jigging, the separation between iron and barite has been greatly improved. In some localities manganese occasionally appears as an impurity, but is fairly easy to eliminate by gravity methods. A considerable percentage of iron and silica is eliminated by being broken free in crushing. Until methods for the recovery of fine ore were introduced a minimum of crushing was done, but modern methods allow more than formerly. The depression years brought about the need for increased recovery of ore handled on the part of the producers and a demand for a higher grade of product on the part of the buyers. Improvements in milling and mining practice have had a far greater effect, however, than merely the production of a better grade of ore with greater recovery. They have opened for mining large areas that a few years ago were considered noncommercial deposits because of their inaccessibility and their high iron content. It is no exaggeration to say that the new methods have more than doubled present known reserves of barite ore of economic value.

Jan 1, 1942

By Emil Gathmann

(San Francisco Meeting, September, 1915) THROUGH wide experience at numerous mills in the United States I have found that there is a decided difference of opinion among the producers of steel as to what constitutes commercially sound steel. Some metallurgists insist upon having, for certain grades of steel, a so-called "open steel," -i.e., one which contains numerous blowholes of varying sizes, and consequently but little volume of true pipe, although a central intermittent shrinkage cavity often extends well down into the ingot: Such blowholes and pipe are expected to weld up during rolling or forging, because their surfaces are not oxidized. Even if this be admitted, included slag particles and a high degree of segregation are bound to be present in the product of such ingots. Blowholes are the result of an oxidized heat, and all heats, unless made or finished in the electric furnace, are oxidized more or less. Subsequent deoxidation, or rather degasification, either in the ladle or in the mold, or in both, is necessary to reduce or prevent blowholes. As is well known, a greater yield of billets or sheets is secured from the ingot by allowing the formation of blowholes, but this is undoubtedly obtained at the expense of the quality of the product. Decided segregation of carbon, phosphorus, and sulphur, as well as small included slag particles, undoubtedly exists throughout the greater portion of all so-called open steel, and cannot be removed by cropping. The first requisite for sound, homogeneous steel ingots and blooms is therefore, in my opinion, so to treat the steel in the furnace, ladle, and mold that "piping" steel is produced. The line of demarcation between harmful and so-called "harmless" blowholes is practically impossible to define. Is it not, therefore, the better and safer practice to use means for the elimination of blowholes and correspondingly reduce the segregation and allow the formation of a well-defined shrinkage cavity or pipe .at the upper end of the ingot? With the relatively cheap deoxidizers available at the present time, e.g., ferro-silicon, aluminum and titanium,

Jan 8, 1915

By R. C. Hepworth

Heaving in roads built on the Mancos Shale is a serious problem in east-central Utah. Heaves are expressed as local bumps, general rises and severe cracking of the pavement. The heaves usually occur in shale road cuts and generally show a seasonal cycle, which reaches a maximum development in the winter. The presence of certain salts, absorption of moisture and physical properties of the subgrade materials were considered, in Utah, to be the main factors in the heaving mechanism. Work done on similar problems elsewhere and studies conducted by the author indicate that the latter two factors are the most important. Results of this investigation indicate that heaving areas are associated with slaking shale or expansive clays, with and without salts present. Laboratory studies show that the initial moisture content of remolded samples and the desiccation history of un- disturbed samples have a major effect on swelling. Swell tests on compacted samples at various temperatures indicate that water has more influence on swell than temperature, except for samples containing sodium sulphate, which swelled with decreasing temperature. Chloride salts inhibited swelling. Tests on shale cores indicate that the stability of slaking shale can be preserved by maintaining its original moisture content. It is concluded that shales and expansive clays, when exposed in road cuts, become desiccated and are subject to expansion when moisture is subsequently available. The seasonal cycle of heaving may possibly be explained by the annual moisture excess and deficiency. To minimize the problem, freshly exposed shale should be kept wet, and the thickness of the subbase and base courses should be increased. The Utah State Department of Highways has been plagued for many years with a distressed condition that develops in roads constructed on the Mancos Shale. Locally these distressed areas are known as heaves, frost boils and alkali boils. These names refer to the surface expression, time of year

Jan 1, 1965

By William E. Newman

When Hugh Lee Pattinson discovered, in 1829, that the crystals formed during the slow cooling of molten lead were poorer, and the remaining liquid richer in silver, than the original lead, an important step was made in the metallurgy of this metal. Being the first process applicable to the desilverization of low-grade lead bullion, it soon found its way into all European countries having such a product to treat, thereby effecting the saving of many ounces of silver annually which previously had been thrown away. The old hand process was expensive, as viewed from the standpoint of more modern methods; the labor was great and the tonnage was small, but on the other hand the results were fairly satisfactory. This process flourished for some time after the introduction of the cheaper Parkes process in 1852 and it is still in use in a few European smelteries. Only one notable improvement was made on the original process, that of Luce and Rozan at Marseilles, France. It consisted in the application of steam for stirring and the tapping of one-third of the liquid lead, through perforated plates covering the tap holes flush with the bottom of the kettle, thus leaving two-thirds in the form of crystals in the original kettle. This modification considerably lowered the operating costs as it permitted of much larger kettles, an increased tonnage and eliminated much of the slow, hard labor of the hand process. The Luce and Rozan process has persisted in its original form to the present day. Stephen Tredinnick, English born, spent most of his years around the Luce and Rozan plants at Marseilles and elsewhere in Europe, coming later to Eureka, Nev., in 1878, to operate the Luce and Rozan plant at that point. Mr. Tredinnick was a competent Luce and Rozan operator and being devoted to the process he firmly believed that with modifications the costs could be so lowered as eventually to supplant the Parkes process. Out of many schemes he decided that this could be accomplished by placing the Luce and Rozan kettles upon hydraulic rams so that each

Jan 1, 1918

NEW MEMBERS The following list comprises the names of those persons who became members during the period Apr. 10 to May 10, 1915: Members ADMAN, WILLIAM, Supt., Susquehanna Coal Co Lykens, Pa. BARTH, CARL G., JR., Min. Engr 6151 Columbia Ave., Philadelphia, Pa. BOOTH, ERIC EDWIN, Min. Engr., Mount Elliott Mine, Selwyn via Cloncurry, North Queensland, Australia. BOYDELL, HARRY CYRIL, Asst. Mgr., Randfontein Central Gold Min. Co., Box 42, Randfontein, Transvaal, South Africa. BRADY, SAMUEL HOWARD, Mine Supt Bohemian Club, .San Francisco, Cal. Buses, HARRY EDWARD, Mine Supt., Engels Copper MiningCo Keddie, Cal.

Jan 6, 1915

By Gerald Edmunds

Castings of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, sometimes nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals .primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is developed to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and therefore the position of the grains is more cornplex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicating that thermal contact was better there than in neighboring areas. The nucleus from which a columnar grain grows may be so oriented that its direction of maximum growth rate does not coincide with the direction of the thermal gradient. In this case the long axis of the grain probably assumes an intermediate position. Notwithstanding these minor irregularities, the situation does exist that the long axes of the columnar grains are generally disposed approximately perpendicular to the mold surface. Schmid and Wassermanl and Nix and Schmid2 have determined the orientation texture of columnar grains in castings of several cubic, tetragonal, hexagonal close-packed and rhombohedra1 metals. For zinc and cadmium, they report the basal plane to be parallel to the columnar grain axes, with no preference for any particular direction in this plane to coincide with the grain axes. This texture, termed a ring fiber texture,3 is uncommon in metals; zinc and cadmium are the only ones reported to exhibit it. Generally, it is stated, a simpler texture exists in which a principal, though not necessarily the most closely packed, crystallographic direction is parallel to the direction of heat flow. In cast magnesium (also hexagonal close packed) they report a digonal axis I, [100] direction, parallel to the direction of heat flow. The writer is not aware of any other orientation-texture determinations on cast polycrystalline hexagonal metals. In view of the observations reported in the present paper it is of interest also to note that Nix and Schmid stated that a

Jan 1, 1941

By T. M. Broderick

INVESTIGATIONS into the possibilities of economically mining and concentrating low-grade iron ores of the Lake Superior region are attract-ing increasing attention. Among the organizations that are carrying on the work are the United States Bureau of Mines, the State of Minne-sota (which spends about $80,000 annually on problems of the 'iron and ferroalloy ores of Minnesota), and the State of Michigan (which spends about $10,000 annually of its iron-ore research). Several of the mining companies are also financing research. Of the states in the Lake Superior district, Minnesota has done most in iron-ore concentration. In 1930, thirty-seven concentrating plants were in operation on the Mesabi Range, beneficiating about one-third of the total ore shipped. About one-half of these plants reduced silica; the others reduced moisture or improved the structure of the ore.1 Research into the possibilities of magnetic concentration of the Eastern Mesabi magnetite ores indicates that vast tonnages of that ore may be utilized at a profit in the not distant future. Magnetic concentration has also been tried at Sellwood, Ontario, on the Moose Mountain deposit, and at the Berkshire mine in Wisconsin on the magnetic ores of the Western Gogebic Range. There have been few attempts to concentrate Michigan iron ores. In order to determine the possibilities of such concentration, iron-ore research has been carried on at the Michigan College of Mining and Technology for the past few years. After a general survey of the iron ores of the state, a program of more detailed experimentation was out-lined, starting with work on the Ironwood formation of the Gogebic Range. The results of this research led to the belief that gravity methods will produce fairly satisfactory concentrates from the parts of the iron formation that are made up of comparatively thick alternating beds of rather high-grade ore and lean chert.

Jan 1, 1933

By Gerald Edmunds

Castings of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, sometimes nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals .primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is developed to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and therefore the position of the grains is more cornplex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicating that thermal contact was better there than in neighboring areas. The nucleus from which a columnar grain grows may be so oriented that its direction of maximum growth rate does not coincide with the direction of the thermal gradient. In this case the long axis of the grain probably assumes an intermediate position. Notwithstanding these minor irregularities, the situation does exist that the long axes of the columnar grains are generally disposed approximately perpendicular to the mold surface. Schmid and Wassermanl and Nix and Schmid2 have determined the orientation texture of columnar grains in castings of several cubic, tetragonal, hexagonal close-packed and rhombohedra1 metals. For zinc and cadmium, they report the basal plane to be parallel to the columnar grain axes, with no preference for any particular direction in this plane to coincide with the grain axes. This texture, termed a ring fiber texture,3 is uncommon in metals; zinc and cadmium are the only ones reported to exhibit it. Generally, it is stated, a simpler texture exists in which a principal, though not necessarily the most closely packed, crystallographic direction is parallel to the direction of heat flow. In cast magnesium (also hexagonal close packed) they report a digonal axis I, [100] direction, parallel to the direction of heat flow. The writer is not aware of any other orientation-texture determinations on cast polycrystalline hexagonal metals. In view of the observations reported in the present paper it is of interest also to note that Nix and Schmid stated that a

Jan 1, 1941

By Frank Feuille, Edward Schuster

As the time allotted is short, we can present only a general idea of the oil laws in the Latin-American republics, as a supplement to Bulletin 206 of the Department of the Interior compiled under the direction of J. W. Thompson of the Bureau of Mines and entitled "Petroleum Laws of All America." We shall not discuss the European colonies in Latin-America nor the island republics. As to the countries discussed, we shall attempt to give the main features of such special petroleum legislation as has been adopted prior to the early part of this year; where no special petroleum laws exist, we must look to the mining codes for light on the petroleum policy. As the laws and regulations for the extraction of the metals are often difficult of application to, and are lacking in many essentials for, the petroleum industry, it is best for persons or companies desiring to enter, on a large scale, into the petroleum exploration and development of countries not having special petroleum legislation, to obtain a concession contract from the executive of the country under consideration, and to have the concession approved by the congress. If this concession, which would then be a special law, contains nothing contrary to the constitution of that country and does not infringe on vested rights of third parties, it should be reasonably safe. If in such country there is some doubt as to whether the petroleum subsoil is owned by the nation or the private surface owner, only public lands should be covered with the concession. Guatemala is the only republic in the group that discriminates directly against foreigners. Bolivia, Ecuador, Mexico and Venezuela require waivers of diplomatic protection.' Colombia requires foreigners to agree to be bound by its alien law. In addition,Mexico makes it unlawful for foreigners to acquire direct ownership of real estate, including mines, within a zone of 50 km. along the coasts and one of 100 km. alongitsland

Jan 1, 1923

By Dorsey A. Lyon, Robert M. Keeney

The utilization of hydro-electriic power in electro-metallurgical industries, aside from purely mechanical operations, may be of two kinds. The electric energy may be used to supply the heat necessary for the performance of the chemical reactions of a metallurgical process, or the electrolytic action of a direct current may be employed for extraction of metals, either in a reduction process or a refining process. In discussing this subject, it is well to distinguish between established industries, which are producing metals and alloys at a, profit by use of the electric current, and the many processes which are either still in the experimental stage or have not even passed the paper stage of development of a patent. That is, we consider electro-metallurgical industries as commercial operations which are now consuming large blocks of electric energy, while processes which are not in commercial operation are only prospective consumers. Also, owing to the difliculty and risk of any attempt to foresee the effect of the European war upon electro-metallurgical industries, we have felt obliged to disregard the war entirely, and state our opinions regardless of its existence. Application of Electric Energy to Metallurgy Disregarding electrolytic refining processes, the applications of electric energy to metallurgy, when considered from a commercial viewpoint, may be classified as follows: Industries Experimental Processes Manufacture of aluminum Electric-furnace smelting of: Electric-furnace manufacture of: Ferro-alloys Copper ore Pig iron Zinc ore Steel In this paper only the above industries and experimental processes will be considered as possible consumers of hydro-electric power in large quan-

Jan 1, 1916

By James Kemp

IN earlier years, the custom prevailed of regarding the anthracite basins as cases of folding with slight development of faulting. Folding is so pronounced and, in the eastern and western Middle Fields, at times so violent, that the inference was a natural one and led to the widespread impression that practically all the disturbances of the seams could be explained in this way. The cross-sections-and maps prepared forty or more years ago for the Second Geological Survey of Pennsylvania, by Mr. Ashburner under Prof. J. P. Lesley, exhibit little else than folds.1 So far as I can discover faults fail in the charts, except in one small case in the Henry Colliery near Plainsville on the outskirts of Wilkes-Barre. Some years ago, while spending a day or two in Wilkes-Barre, under the guidance of R. V. Norris, I looked over some recent and accurate cross-sections of a number of the large collieries and was deeply impressed with the peculiar behavior of some of the seams and the intervening shales. Thus, a seam might present a small, more or less overturned fold, rising 30 to 50 ft. (9 to 15m.) above its general course, and yet the movement would be taken up in the overlying shales, so as hardly to be noticeable in the seams next above or below. These and similar anomalies, especially when shown with the accuracy of engineer's surveys, possess great scientific and practical interest, bearing as .they do, not alone on coal mining, but on theoretical geology and the actual behavior of strata under great compressive stresses. In preparation for the semicentennial meeting of the Institute, an, effort was therefore made to secure some of the most interesting sections for presentation to the members. The collection of illustrations here shown is mainly due to, Mr. Douglas Bunting of the local committee, to whom and to the contributing companies acknowledgments are due.

Jan 1, 1922

By G. Sachs, E. J. Ripling, J. J. Lynch

INTRODUCTION General IT is general practice to evaluate the strength properties of a particular metal from its stress-strain [(S1 - E1]) curve obtained by means of a conventional tension test. Such a stress-strain curve, Fig I, illustrates two important properties of a metal, its ability to strain harden, and its ability to withstand a certain limiting stress, the "fracture stress,"[ (s'r)], and a certain limiting strain, the "ductility" [(e1)], before it fails by separation. These two fracturing characteristics are the coordinates of the point of fracture in Fig I. In the case of a metal which necks in a tension test, both the fracture stress and the ductility (measured in a tension test) are dependent upon (a) the shape of the neck and (b) average values of the stresses and strains over the cross section at the moment of fracture. However, for the purpose of this investigation, these average quantities, rather than the actual values, may be considered for reasons of simplicity. It appears that the conclusions also hold true if the analysis were carried out for actual values of fracture stress and ductility at the locus of failure. In this paper, the effects of straining (at room temperature) by various methods on [ ] the above metal characteristics, which were determined by subsequent tension tests will be discussed. According to our present knowledge, any such prestraining results in a stress-strain curve (in subsequent testing by tension), Fig 2, the general shape, or flow characteristics, of which can be derived from the original stress-strain curve of the unstrained metal minus a certain portion exhausted by the initial straining. This phenomenon is called strain hardening, and may be measured by the magnitude of the cut-off, or the "effective strain," from which the new curve must start in order to coincide in its plastic branch with the original stress-strain curve.

Jan 1, 1948

By Edward Schuster, Frank Feuille

As the time allotted is short, we can present only a general idea of the oil laws in the Latin-American republics, as a supplement to Bulletin 206 of the Department of the Interior compiled under the direction of J. W. Thompson of the Bureau of Mines and entitled "Petroleum Laws of All America." We shall not discuss the European colonies in Latin-America nor the island republics. As to the countries discussed, we shall attempt to give the main features of such special petroleum legislation as has been adopted prior to the early part of this year; where no special petroleum laws exist, we must look to the mining codes for light on the petroleum policy. As the laws and regulations for the extraction of the metals are often difficult of application to, and are lacking in many essentials for, the petroleum industry, it is best for persons or companies desiring to enter, on a large scale, into the petroleum exploration and development of countries not having special petroleum legislation, to obtain a concession contract from the executive of the country under consideration, and to have the concession approved by the congress. If this concession, which would then be a special law, contains nothing contrary to the constitution of that country and does not infringe on vested rights of third parties, it should be reasonably safe. If in such country there is some doubt as to whether the petroleum subsoil is owned by the nation or the private surface owner, only public lands should be covered with the concession. Guatemala is the only republic in the group that discriminates directly against foreigners. Bolivia, Ecuador, Mexico and Venezuela require waivers of diplomatic protection.' Colombia requires foreigners to agree to be bound by its alien law. In addition,Mexico makes it unlawful for foreigners to acquire direct ownership of real estate, including mines, within a zone of 50 km. along the coasts and one of 100 km. alongitsland

Jan 1, 1923

By C. Cronquist

Since April, 1962, Shell Oil Co. has operated a peripheral line-drive waterflood of the 10.750-ft lower Tuscaloosa (Cretaceous) Denkman sand in the Little Creek field. Located in southwestern Mississippi in the lower Tuscaloosa trend, the field was discovered by Shell in Jan., 1958. Among the largest in the trend, the accumulation is controlled stratigraphically and occurs in an extensive series of alluvial-point bar deposits across a nose that dips gently to the south. The crude oil is 39" API gravity and was highly undersaturated at initial conditions. Early production behavior indicated a depletion drive with slight water influx; primary recovery wm estimated to be 25 million bbl, or 24.5 percent of stock-tank oil originally in place. A.s a result of a favorable mobility ratio and remarkably uniform rock properties, the volumetric sweep eficiency in the waterflood has exceeded 90 percent. Despite the high connate water saturation (56 percent), the displacement efficiency by water injection has been quite efficient, contrary to traditional concepts. Based on observed field flood-out performance, ultimate recovery is calculated to be 46 million bbl. As anticipated, the production rate began declining during 1964 due to a continu ing reducrion in the number of producing wells as flood fronts advanced across the field. Cumulative recovery as of Jan., 1968, was 44.8 million bbl; waterflood operations ~hould be complete by 1970. Introduction Most waterfloods described in reservoir engineering literature involve pattern operations, the most common of which is the five-spot pattern. Only occasiona'lly are linear drives described, even though there probably are increasing numbers being put into operation. Increasing use of linear floods may reflect the accelerating trend towards early application of fluid-injection programs when linear drives are more efficient, as was the case at Little Creek. However. the Little Creek operation is unusual in several respects. It is one of a few successful waterfloods conducted in sands with connate water saturations approaching 60 percent, and it is among the deepest successful water-floods being operated anywhere. Development The Little Creek field was discovered in Jan., 1958, in the lower Tuscaloosa trend in southwestern Mississippi (Fig. 1). The discovery well, Shell-Lemann No. 1, was drilled on a seismic closure about 2 miles southeast of lower Tuscaloosa production at Sweetwater. The well was completed in the Denkman sand at 10,752 ft, and on initial potential it flowed 588 BOPD of 39" API crude on a %+-in. choke; psi was 730 and GOR was 442:l. Development proceeded rapidly on 40-acre spacing, and by the end of 1958 the field was producing approximately 9,100 B/D from 56 wells. Almost all this production came from the northern half of the field. The southern part was discovered in Nov., 1958, at a location almost 2 miles from previously established production. Subsequent drilling established an apparent conneotion about half a mile wide between the twd areas. Development of the field was practically complete by 1961 with the drilling of 155 producers and 35 dry holes. Some early wells were completed open hole but moslt are completed with casing cemented through the productive interval and perforated for production. Geology The lower Tuscaloosa structure in this area is a north-south nose with maximum dips of about 2" on the flanks. There is no discernible faulting at the producing horizon. Productive limits of the field are shown in Fig. 2, which is contoured on a marker just above the main productive zone. A common water level at 10,415 ft subsea was logged at both the northwest and southeast ends of the field. There is a gross oil column of nearly 100 ft (Fig. 2). Since there is less than 40 ft of closure, it is apparent that bhe accumubtion is controlled stratigraphically, being limited by a sand pinch-out across the creslt of the nose. The total produc-

Jan 1, 1969

By L. F. Mondolfo, B. E. Sundquist

The crystallographic orientation relationships resulting when lead is nucleated from the liquid by Ni, Cu, Ag, and Ge were determined. For each nucleating agent several definite orientatioz relationships were found. These relationships seemed to be controlled by good symmetry relations and low crystallographic disregistry between mating planes. For any given nucleating agent the under colling for nucleation was found fairly constant and independent of the orientation relationship and consequent disregistry. It was also found that, upon re melting and refreezing the Pb, the orientation relationship was changed. These findings prove that crystallographic disregistry is not the controlling factor in heterogeneous nucleation from the liquid. The results of this investigation tend to confirm the theory presented in a preceding paper that heterogeneous nucleation starts with the formation of an adsorbed layer of nucleated metal on the nucleat-ing impurity. Evidence is given that cavities in the nucleating agent act as centers of nucleation. IT has long been known' that solid extraneous particles are active in catalyzing phase transformations that occur in a system, particularly condensation and crystallization. It is well established that these heterogeneities act as catalysts by providing surfaces upon which nuclei of the precipitating phase can form with activation energies smaller than those required for homogeneous nucleation. Numerous investigations have shown that in this process of heterogeneous nucleation: a) the nucleus forms with one, or several, definite crystallographic orientation relationships with the nucleating phase2-4 and b) that there is a small range of undercoolings or super saturations characteristic of the nucleation of a given solid on a given Substrate.5-10 Turnbull and vonnegut11 have developed a theory based on theories developed by Volmer12 and Turn-bull and Fisher1= for heterogeneous nucleation from gases and liquids, that relates the super saturation or undercooling required for nucleation to the dis-registry between the lattices of the nucleus and the nucleating agent. This theory predicts that nucleation should occur with the orientation relationship between the nucleus and nucleating agent that minimizes the disregistry. Further, it predicts that the undercooling or super saturation necessary for nucleation should be a function of the disregistry. Numerous investigations have dealt with the orientation relationships resulting from the condensation of vapors onto crystalline solid substrates2,3 and a few with the nucleation of one phase by a second phase in solidification4,14. Others have dealt with the supersaturation8-10 and undercooling5-7 associated with nucleation in condensation and solidification respectively. However, there is virtually no report that gives both of these factors for the same system. In this investigation a study was made of the undercoolings and orientation relationships resulting when Pb is nucleated from the liquid by Ni, Cu, Ag, and Ge. It was the purpose of this investigation to check the Turnbull-Vonnegut theory, i.e., the importance of crystallographic disregistry between nucleating catalyst and nucleated metal. The results indicate that disregistry is not an important factor in nucleation and that the nucleation process is probably somewhat more complex than current theories suggest. EXPERMENTAL PROCEDURE Small single crystals of nickel, copper, silver, and germanium were prepared from materials of four to five nines purity, and the Pb used was also 99.999+ pet pure. Cu and Ag single crystals were prepared by sealing small chips of Cu or Ag in an evacuated quartz capsule and heating the capsule at 2000°F for 1 hr before cooling. Nickel crystals of 200 diam were also prepared in evacuated quartz capsules, but melting was done by heating the capsules in an oxy-acetylene flame for a few minutes. These spheres were invariably polycrystalline so

Jan 1, 1962

By Robert F. Mehl, Gerhard Derge

The gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transformation rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2; since then several important papers have appeared. Our present knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-centered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-centered alpha lattices in tempered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: {111} ?//{110}a [110] ?// [111]a (This notation is used throughout as the most descriptive means of expressing the fact that any (111) plane of the gamma phase may be parallel to any (110) plane of the alpha phase, and that a [110] direction in a particular (111)? plane is parallel to a [Ill] direction in the corresponding (110)a plane.) From these relationships the atomic movements that transform the gamma lattice into the alpha may be inferred. In the present experiment these may be considered as consisting primarily in a shear of the atoms parallel to the {111} planes in [110]? Directions

Jan 1, 1937

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man's thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life's work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe's pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe's work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book' on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe's ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By H. D. Williams, R. A. Scriven

The distribution of elevation angle of finite plane facets distributed symmetrically about a given axis is derived in terms of the angular distribution of lines which these facets produce in a plane section parallel to the axis. It is assumed that the facets are not markedly elongated in preferential directions. The theory is intended for application to the angular distribution in polycrystalline metals of slip planes and of particular grain boundaries on which certain phenomena such as cavitation can occuv. Illustrative examples are given in closed form and simple numerical techniques are de-ueloped for practical application. The results are applied to the distribution of cavitated boundaries in a copper specimen after fatigue at 400°C and it is found that voids form on the boundaries that exper~enced maximum shear stress. When investigating the distribution of elevation angle between a given axis and planes symmetrically distributed about this axis the angular distribution observed in a plane section parallel to the axis is not necessarily the same as the required distribution. Consequently a technique for processing the results obtained by sectioning methods is required. An example where such a technique would find application is in the problem of intercrystalline void formation during uniaxial tensile creep. Two theories have been proposed to explain this cavitation in terms of the normal and the shear components of stress, respectively. Hull and Rimmer (1959) postulate that the growth of intercrystalline voids is controlled by the rate of supply of vacancies from the grain boundary, the local vacancy concentration being proportional to the normal stress on the boundary. Gifkins (1956) considers that slip arising within a grain causes a ledge to be formed at the grain boundary which is subsequently opened up into a cavity by grain boundary sliding. It might be possible to differentiate between these mechanisms by determining the angular distribution of grain boundaries containing cavities since the former theory predicts a predominance of cavitated facets normal to the stress direction whereas the latter should favor an angle of 45 deg to this direction. In a similar manner an indication may be obtained of the type of mechanism responsible for intercrystalline cavitation during high-temperature fatigue. Davies and Wilshire (1962) have analyzed the slip-plane distribution in a nickel specimen but the problem was not treated in any detail nor was any account taken of the finite extent of the planes being sectioned. Hilliard (1962) has given a very general account of how anisotropy in the microstruciure can be related to measurements taken in one or more plane sections by expressing both the measured and the true angular distributions as expansions in spherical harmonics.* The present analysis is con-

Jan 1, 1965

By T. L. Joseph

It is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man's thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life's work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe's pioneer work in the field of metallurgy.. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that underlies the production of steel. Although Dr. Howe's work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book' on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe's ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of- much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blastfurnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1947

By R. J. Arsenault

The yield drop that occurs in tantalum, Cu-AZ. and Ag-Al was investigated as a function of strain rate and at several temperatures. From the strain-rate dependence of the yield drop an activation volume was calculated and found to agree with that obtained from differential strain-mte tests. The temperature dependence of the yield drop can he explained in terms of the parameter temperature divided by activation volume. The yield drop is attributed to the rapid multiplication of dislocations during their motion. THE yield-point or yield-drop (upper yield stress minus the lower yield stress) phenomenon has been the subject of numerous investigations1-9 in both bcc and fcc metals. Also, there is no dearth of theoretical explanations10-20 to account for the yield-point phenomenon. The present explanations can be divided into two categories: the concept of dislocation locking and subsequent unlocking and the concept of multiplication of dislocations due to their motion. The Vottrell10,11mechanism of locking and unlocking, as applied to bcc metals, is the best known of the three proposed locking mechanisms. The two additional mechanisms, short-range order (SRO)7,16,17 and Suzuki-type locking,14,15 have been employed to account for the existence of yield points in fcc metals. The experimental evidence supporting the locking of dislocations, especially in bcc metals, is well-established. The dependence of the yield point on interstitial concentrations,' the kinetics of strain aging,2 and the observations by electron-transmission microscopy18 are some of these experimental results. The number of experimental observations supporting dislocation locking in fcc metals is not as extensive as in bcc metals. The unlocking of dislocations, which actually is supposed to account for the yield drop, is by no means well-established by experimental results for either bcc or fcc metals. The similar temperature dependence6 of the yielding and plastic flow is one of the experimental factors that cannot be explained in terms of the unlocking of dislocations. The mechanism based on the rapid multiplication of dislocations has been proposed by several investigators. 18-20 Johnston and Gilman19 have proposed a detailed model of yielding, which was later employed by Hahn21 to predict quantitatively the yield drop in iron. This mechanism was discussed in a previous paper22 and several limitations were pointed out. In the same paper it was shown that an activation volume could be obtained from the strain-rate dependence of the yield drop and that a correlation existed between the activation volumes obtained from the yield-drop tests and from differen-

Jan 1, 1964