Search Documents

By F. N. Rhines, W. S. Pellini

In many of the otherwise well established alloy phase diagrams the solidus curves (temperatures at which liquid first appears upon melting) have not been located accurately, chiefly because the experimental techniques that have been most popular for determining solidus temperatures have been both cumbersome and subject to large errors. C. E. Homer and H. Plummerl have described a sensitive and at the same time a very simple technique for locating the solidus curves in a number of alloys of tin. Their method consists simply in noting the temperature at which a specimen of the alloy ruptures under the influence of a light bending force. Although this method is not new, it has been little used for this purpose in the past; nevertheless, it appears so attractive in its possibilities of speed, simplicity, and precision that the investigations presently to be described were undertaken to verify its merits. The redetermination of the solidus and eutectic temperatures of the lead-antimony system was employed as a medium of experimentation. New values obtained in this way are believcd to be sufficiently precise to warrant a revision of the currently accepted lead-antimony phase diagram (Fig. I). Determinations of the solidus of the lead-rich lead-antimony alloy series have been published by X. S. Dean2 and by E. E. Schumacher and F. C. Nix. Their points are represented in Fig. I. In their work the solidus was not located at antimony collcentrations greater than 2 per cent; the curve was presumed to meet the eutectic horizontal at an antimony concentration of about 2.5 per cent. In the present studies the solidus has been traced to 3.5 per cent, where the eutectic horizontal is intersected (Table I and Fig. I). Within the range investigated by Dean and by Schumacher and Nix the agreement with their values is good. H. Seltz and B. De Witt,4 on the basis of activity measurements, have calculated that the intersection of the solidus and the eutectic reaction horizontal should lie at 3.86 per cent of antimony. The following determinations of the eutectic temperature have been reported: Roland-Gosselin,5 228°C.; Ewen,6 228OC.; J. E. Stead,7 24g°C.; Campbell,8 228°C.; W. Gontermann,9 245' to 252°C.; R. Loebe,lo 245°C.; E. Heyn and 0. Bauer,ll 245°C.; H. Endo,12 250°C.; R. S. Dean,= 247' to 258°C.; E. Abel, O. Redlich, and J. Adier,13 245°C.; W. Broniewski and L. Sliwowski,14 250' to 252°C.; H. Seltz and B. De Witt,4 25o°C. A temperature of 247°C. appears to have been generally accepted in recent years; it is the value most frequently obtained by the method of cooling curves. Values below 247°C. have usually been obtained by inferior cooling-curve techniques; those above 250°C., by the method of heating

Jan 1, 1943

By W. S. Pellini, F. N. Rhines

In many of the otherwise well established alloy phase diagrams the solidus curves (temperatures at which liquid first appears upon melting) have not been located accurately, chiefly because the experimental techniques that have been most popular for determining solidus temperatures have been both cumbersome and subject to large errors. C. E. Homer and H. Plummerl have described a sensitive and at the same time a very simple technique for locating the solidus curves in a number of alloys of tin. Their method consists simply in noting the temperature at which a specimen of the alloy ruptures under the influence of a light bending force. Although this method is not new, it has been little used for this purpose in the past; nevertheless, it appears so attractive in its possibilities of speed, simplicity, and precision that the investigations presently to be described were undertaken to verify its merits. The redetermination of the solidus and eutectic temperatures of the lead-antimony system was employed as a medium of experimentation. New values obtained in this way are believcd to be sufficiently precise to warrant a revision of the currently accepted lead-antimony phase diagram (Fig. I). Determinations of the solidus of the lead-rich lead-antimony alloy series have been published by X. S. Dean2 and by E. E. Schumacher and F. C. Nix. Their points are represented in Fig. I. In their work the solidus was not located at antimony collcentrations greater than 2 per cent; the curve was presumed to meet the eutectic horizontal at an antimony concentration of about 2.5 per cent. In the present studies the solidus has been traced to 3.5 per cent, where the eutectic horizontal is intersected (Table I and Fig. I). Within the range investigated by Dean and by Schumacher and Nix the agreement with their values is good. H. Seltz and B. De Witt,4 on the basis of activity measurements, have calculated that the intersection of the solidus and the eutectic reaction horizontal should lie at 3.86 per cent of antimony. The following determinations of the eutectic temperature have been reported: Roland-Gosselin,5 228°C.; Ewen,6 228OC.; J. E. Stead,7 24g°C.; Campbell,8 228°C.; W. Gontermann,9 245' to 252°C.; R. Loebe,lo 245°C.; E. Heyn and 0. Bauer,ll 245°C.; H. Endo,12 250°C.; R. S. Dean,= 247' to 258°C.; E. Abel, O. Redlich, and J. Adier,13 245°C.; W. Broniewski and L. Sliwowski,14 250' to 252°C.; H. Seltz and B. De Witt,4 25o°C. A temperature of 247°C. appears to have been generally accepted in recent years; it is the value most frequently obtained by the method of cooling curves. Values below 247°C. have usually been obtained by inferior cooling-curve techniques; those above 250°C., by the method of heating

Jan 1, 1943

By Yves Dardel

THE literature concerning the remelting of aluminum and its alloys is very rich. Unfortunately the greater part of the papers about this subject have no scientific value, for the theories or explanations are too often in opposition to the laws of physical chemistry. Furthermore only a few of the methods of purification1,2 are considered in the literature. Hence it has seemed necessary to the author to sketch a general theory of the purification of secondary aluminum. The purpose of the purification is to eliminate the impurities that the charges and the atmosphere of the furnaces bring into the bath during the successive remeltings. Indeed scrap as well as metal can be used when soiled with oil, greases, water, .. , if it has been sufficiently dried and contains oxides. At the melting point of the metal, the oils and greases are decomposed into their constituent elements H2, 02, H2O, C02, CO, CH4, and others. These gases are added to the corresponding gases in the atmosphere of the furnace. The impurities introduced into the metal during the remelting will accordingly be the products resulting from the action of these gases on the liquid bath. The quantity of hydrogen that is soluble in aluminum and its alloys is given by the relation of Sieverts3 as a function of its partial pressure PH2 in the atmosphere [m = K _%/PH, [I]] where K is a constant, which depends only upon the temperature and increases with it. The experiments of Röntgen and Braun4, Röntgen and Möller5, Bircumshaw6 and Winterhager7 have rendered it possible to determine the value of K, when the temperature is inferior to 1.000°K. One obtains: [log K = - 4,702.5 + 0.238 [2]] Besides its usual signification, the term PH2 represents also the internal pressure of dissolved hydrogen, since in the equilibrium, that is, when no gas exchange occurs between the two phases, the pressures of hydrogen in the metal and in the atmosphere must be equal. Eq I shows that when the partial pressure of H2 increases the amount of dissolved hydrogen in equilibrium increases, and that, if the contrary occurs, the quantity of H2 should diminish. However, if for any reason the diffusion of hydrogen is hindered and the total amount of dissolved gas remains constant while the temperature lowers, the internal pressure of H2 increases until it reaches the value of the hydrostatic pressure. At this point, bubbles of hydrogen appear in the bath and escape out of it. The amount of hydrogen in the metal is then limited by a maximum depending on the hydrostatic pressure, which is practically equal to one atmosphere. Indeed hydrogen does not accumulate in the form of a hydride appearing as a separate solid phase. However, even the mechanism of the solubility is not yet elucidated. One does not know exactly as yet, whether the

Jan 1, 1947

By Thomas A. Read

The internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of ioo when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose—that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals mill be presented. Experimental Procedure The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrcment A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders M in. in diameter and I 1/2 to 21/2 in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is 1/4 in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By Thomas A. Read

The internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of ioo when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose—that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals mill be presented. Experimental Procedure The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrcment A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders M in. in diameter and I 1/2 to 21/2 in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is 1/4 in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By A. W. Gauger

IT is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have 0n Society. The development of a machine to replace several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and technology as well as in the training of future engineers and technologists. MAGNITUDE OF THE FUELS INDUSTRY Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the comparative values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13 1/4 billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone annually exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1020 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to 1939, $46,409,727,000 of metallic products, S80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,000,000 of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our country. As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942

By John Chipman, Helen Towers

DEVELOPMENT of a simple radioactive tracer technique for measurement of the diffusion coefficient of calcium ion in liquid slag has already been reported. The investigation was of a preliminary nature designed to explore the possibilities of using radioactive isotopes and to establish a method, and no great accuracy was claimed for the results. It was shown, however, that Ca15 could be used successfully, and the values obtained for the diffusion coefficient appeared to be of the right order of magnitude. However, it was considered that a better technique could be devised for carrying out the diffusion. The experiments were, therefore, continued to find a more accurate method, to check the calcium results, and to extend the investigation to include measurements of the diffusion coefficient of silicon in the same slag. There were two flaws in the original technique. Convection was the cause of too many failures, and the interface between the two slags in the diffusion cell was curved rather than plane, probably due to a surface tension effect caused by the addition of the tracer Ca45 in the form of chloride. Two methods of overcoming these defects were tried. Since it was planned to study diffusion of the short-lived isotope Si"' also, the development of methods was restricted to those which gave promise of being reasonably rapid. Method 1—The principle was identical to that previously used with respect to the diffusion conditions, but there were three differences in technique. Temperature control was more rigid, the tracer was added to the slag as Ca45O rather than the chloride and, finally, an effort was made to translate to high temperatures the elegant method developed by Cohen and BruinV or bringing together the two liquid layers and beginning the diffusion. A master slag was melted in graphite, ground to a fine powder, and analyzed (38.5 pct Ca0-20.9 pct Al2O3-40.5 pct SiO2). The tracer was received as Ca45C12 in an aqueous solution of CaC12 + HC1. From this, calcium oxalate was precipitated, ignited to calcium oxide, and added as such to the slag to give an activity of approximately 5 µc per g. The mixture was then melted into the form of a cylinder 3/16 in. diam and about 1 in. long. A solution identical to the tracer solution without Ca45 was given exactly the same treatment. The resulting Ca40O was mixed with that slag which was to form the tracer-free half of the diffusion cell, and this was likewise melted into a cylinder of the same size. Slag cylinders, two with and two without Ca15, were set in graphite blocks as shown in Fig. 1, and the crucible was lowered into position in the fur-

Jan 1, 1958

By A. T. English

X-ray dif action techniques were used to investigate ordering and domain coalescence for the B2 (CsC1) superlattice in this alloy. Essentially complete disorder is obtainable by drastic quenching. isothertmal ordering occurs very rapidly at temperatures between 565° and 680°C, only a few seconds being required for development of substantial long-range order. A very fine antiphase dormain structure, found in samples annealed for short times, undergoes coalescence with further annealing. Domain "size" is found proportional to (t)1/2 . This Yate law can be derived by adapting the formalism of Hillert's analysis 01- metallurgical grain growth. For this Purpose the material is descvibed in terms of a "Swiss-cheese " structure, consisting of two multiply connected, mutually intertwined domain volumes. The observed activation enevgy for coalescence, 70 kcal per g-atom, agrees with an estit~lated value ,for volume diffusion in disordered rrzaterial. It is suggesled that the experimental value vejlects the substantially disordered environment of mobile vacancies located in the moving antiphase domain boundary. The alloy Fe-Co-2V is bcc below about 900'C and orders into a B2 (CsC1) superlattice below about 730c It has important applications in magnetic components, including many requiring extensive cold rolling.* example, Marcinkowski and Brown6 observed a re1atively small as-quenched domain size of about 250Å in B2 Fe3A1. Since there appear to be no published data on domain coalescence in B2 alloys, this process was studied in detail. MATERIALS AND EXPERIMENTAL TECHNIQUES A commercial high-purity alloy, nominally 49 Fe-49Co-2V, was obtained from the Arnold Engineering Co. in the form of cold-rolled sheet 0.004 in. thick. Samples were annealed for 1 hr at 800°C in dry H2 to produce disorder and quenched into iced brine. They were then annealed in a nitrate-nitrite salt bath for various times at temperatures between 525° and 625°C. Estimates of the LRO parameter S and the APD size D were made using established X-ray diffraction techniques. Superlattice peaks are best observed using CoKa radiation, for which the value of (fFe-fCo) is maximized. Peak-to-background intensity ratio was improved by filtering CoKß from the incident beam to eliminate sample fluorescence, and by using a pulse-height analyzer. The LRO parameter S was computed from the ratio of integrated intensities I 100/I 200- Owing presumably to systematic errors associated with the presence of crystallographic texture and X-ray extinction, only rough agreement was obtained between experimental and theoretical (absolute) intensity ratios. For this reason certain experimental refinements (e.g., use of balanced filters) were considered superfluous and were omitted. Emphasis was placed on maximizing intensity in order to reduce the time taken to accurately determine the contour of the very small (loo), peak. This was done by point counting 105 counts at appropriate intervals. Background intensity averaged about 1200 cps.

Jan 1, 1967

By H. Hooykaas

A few years ago Marsal published a method of predicting oil recovery as a function of time for an edge-water-drive reservoir with several rows of wells.' The method is based solely on oil- and water-production data obtained during a short period for the first row of wells and the gross productions (past and future) of all wells. This paper presents a streamlined version of the original publication and experimental evidence showing the reliability of this version. For this purpose scaled experirnents were performed in a large model (750 X 500 X 23 cm, 24.4 ft X 16.2 ft X 8.9 in.) in which edge-water-drive reservoirs with three rows of production wells were simulated. From the results of the experiments it is concluded that the method gives a fairly accurate prediction of the future production behavior of the reservoir and enables us to select the most profitable production plan. Results obtained with the method were always slightly conservative. INTRODUCTION The calculation method developed by Marsal aims at forecasting future reservoir behavior.' It can be applied to floods in which a number of down-dip wells are rapidly going to water. Essentially it is a method for predicting the future behavior of the up-structure wells on the basis of the observed behavior of the down-structure wells. As such, the method is especially useful for predicting behavior of edge-water drives toward several rows of wells. The requirement to be met for justifying the approach is identity of production mechanism in all regions of the reservoir. The attraction of the method then lies in the fact that it applies even when we have no complete description of the prevailing production mechanism. The original publication was in the German language and for this reason, perhaps, did not attract widespread attention. In our opinion it deserves to do so because it does offer in a simple way results which are in fair agreement with observed data. The aim of the present paper is to bring the method to the attention of a wider audience. The method in its most simplified form is reviewed and experimental data in support of it are presented. PRINCIPLES To show Marsal's principle. we will first write the continuity equation for very simple conditions, linear flow (in the positive x-direction) in an incompressible porous body [cross-section A(x), porosity +(x)], saturated with incompressible fluids (oil saturation S). When the oil in this formation is displaced by water, injected at x = 0 (inlet face), we get where q(t) is the total gross displacement rate and f the fractional oil flow. The equation can be solved if we make the assumptions: (1 ) that the fractional oil flow (f) is a univalent function of saturation (S); and (2) that the function is the same throughout the porous medium. Then: f = f(S) Solving this equation with the method of characteristics, we obtain

Jan 1, 1966

By Howard A. Meyerhoff

IN western Argentina, in the Province of Mendoza and the Territory of Neuquén, there is a series of solid bitumen deposits which are claimed to be the most extensive in the world. In a linear belt 500 km (311 miles) long, roughly paralleling the axis of the Andes but occupying a variety of positions with respect to the orogenic structures, more than 100 outcrops have been reported. Approximately 70 of these have been prospected, and some mining has been planned or attempted for about half this number. Limited tonnage, high sulphur content, inaccessibility, labor shortages, and disastrous fires have taken a heavy toll among these operations, and in 1947, only 4 deposits were being actively mined, but 8 more were being explored and developed with a view to placing them in production. Inasmuch as these deposits are currently yielding a substantial fraction of Argentina's limited domestic supply of solid fuels, a brief account of the deposits and of the small industry based upon them will provide a commentary on Argentina's fuel problem. CHARACTER OF SOLID BITUMENS The solid bitumens of Mendoza and Neuquén are petroleum derivatives, as is indicated by the following ultimate analysis: [CONSTITUENTS PER CENT Hydrogen6.8 Carbon82.4 Nit.rogenI.6 Oxygen2.7 Sulphur2.2 Ash4.3 100.0] In physical appearance they bear a close resemblance to coal and are commonly called carbón. Their specific gravity has an extreme range of 1.10 to 1.777 in 36 samples weighed, but the average is between 1.14 and 1.24. The material is black, lustrous to dull, with blocky to sub-conchoidal fracture. Though brittle, the purest material is softer than anthracite and exhibits slightly more cohesion. This bituminous material is generally known as asfaltita or asphaltite, but definitive chemical studies indicate that the term asphaltite or grahamite can be applied correctly only to the exceptionally pure material of the Auca Mahuida district in Neuquén. Some other name should be used for the chemically variable bitumens found in all other districts, and the designation "asphaltitic pyrobitumen" has been proposed by Carlos A. S. Piscione.1 At the present time these bitumens, are finding favor as solid fuel and as a gas-producing medium. They yield heat values of 8650 to 9750 cal,2 or 14,500 to 16,750 Btu per pound, and in consequence of their excellent heating qualities and the scarcity of imported coal, they are marketed as far away as Buenos Aires at a price of go to 95 pesos, or approximately $22 to 23, per metric ton. In burning, the material swells and decomposes into solid, fluid, and gaseous fractions which burn violently though nonexplosively. Its combustibility has been responsible for disasters and virtually complete destruction at Mina La Esperanza and Mina Santa Marta, and for minor mishaps elsewhere, as at Mina Escondida in August 1947.

Jan 1, 1947

By M. E. Wadsworth, R. C. Peterson, W. M. Fassell

The temperature and pressure dependence of the reaction of tantalum in oxygen were investigated from 500° to 1000°C at pressures from 10 mm Hg to 600 psi total oxygen pressure. Tantalum was found to oxidize linearly under the above conditions. Three distinct regions of temperature dependence were found with different energies of activation. From 500° to 600°C the rate of oxidation of tantalum was found to be essentially independent of the oxygen pressure at the pressure investigated. The oxidation rate increases rapidly with an increase in pressure from 600' to 800°C. The dependence of the oxidation rate on the bulk concentration may be expressed by V = k'?, where k' is the specific rate constant and ?=k1Co2/(l + K1Co2), where k, is the equilibrium constant for the adsorption of oxygen on tantalum. ONLY a limited amount of data has been presented in the literature on the oxidation behavior of tantalum metal. Some values of its oxidation rate were reported in the Corroston Handbook' and by McAdams and Geil.' The first extensive investigation of tantalum was the work of Gulbransen and Andrews." They determined the reaction rates of tantalum in O2 and N2. Their results indicate that this metal follows the parabolic law in the temperature range of 250" to 450°C in O2 at pressures of 7.6 cm Hg with an activation energy of 27,400 cal per mol. In nitrogen, the metal follows the parabolic law from 500" to 800°C at 7.6 cm pressure. All experimental determinations were of 2 hr or less duration and deviations from the parabolic rate conceivably could occur at longer times. A spectrophotometric study of the oxidation of tantalum by Waber, Sturdy, Wise, and Tipton' indicated good agreement between this method and the microbalance technique. The experiments were conducted in air from 220" to 350°C. The metal was found to follow the logarithmic law up to 320°C and the parabolic law at higher temperatures. The activation energies in the logarithmic region were reported as 12.57 kcal per mol and 12.0 kcal per mol, respectively, for the microgravimetric and spectrophotometric methods. In the parabolic region the activation energy was found to be 27.2 kcal per mol, in good agreement with the value of Gulbransen and Andrews." The present paper is concerned with the behavior of tantalum from 500" to 1000°C in oxygen at pressures ranging from 1/2 to 40.8 atm pressure. Earlier preliminary data by McKewan5,6 indicated the following facts concerning the behavior of tantalum: 1—At temperatures from 500" to 600°C, the metal followed the linear law. 2—At 575°C the rate of oxidation was found to increase with O2 pressure. 3—The Arrhenius plot in this temperature region was nonlinear. The nonlinearity of the Arrhenius plot was indicative of a more complex behavior than originally suspected for this metal.

Jan 1, 1955

By Henry F. Hebley

This paper brings within the compass of one comparatively brief article a general description of the situation concerning the nation's water resources. It touches upon the phenomenal growth in the demand for water supply and emphasizes the problems facing the coal industry both with regard to acid mine water drainage discharged from active and abandoned mines and the suspended solids discharged to the stream system from wet coal preparation plants. IT must always be remembered, with regard to the problem of water-borne industrial wastes, that stream pollution from any cause is just one factor in the comprehensive problem of water supply in modern times. Industries nonexistent 25 years ago are now flourishing, and supplies of water piped to homes and apartments, as well as the greater number of plumbing fixtures per dwelling and per building, have created an ever growing demand on the country's water resources. Indication of this rapid growth in demand is shown in Table I, which is quoted from Abrams. of Texas increased 287% and the water consumption 7000 per cent." The domestic load varies greatly, depending on the extent of the available supply and the habits of the community. According to the report of the President's Water Resources Policy Commission' the United States Public Health Service reported a national average of 127 gal per capita per day, varying from 60 gal in communities of 500 persons to 140 or 150 gal in cities of 10,000 or over. Other critical areas may be cited to illustrate the inter-relation between new industrial processes and the demands for water in the area where the new enterprise is located. Powell and Wilson have pointed out that during World War 11, in the vicinity of Louisville, Ky., a rapid expansion of industry took place, consisting of numerous synthetic rubber plants. The demand for water increased from 37 million gal per day in 1937 to 62 million gal in 1943. These heavy requirements drew down the supply stored in the water-bearing aquifers to such an extent that urgent plans for recharging were considered. Similar situations have developed in the Los Angeles area and in the vicinity of Texas City. Warne4 has drawn attention to the situation in Los Angeles area, where in the West Basin the withdrawal of ground water in 1945 was 90,000 acre-ft, almost double the amount of the natural fresh water recharge. The draw down has been so severe that the level of the ground water is now below sea level, and sea water is invading the West Basin aquifers at rates up to 300 ft per year. In the Report of the Engineers Joint Council it is pointed out that in the area of Texas City the ground water table has been critically lowered. In 1930 the daily withdrawal from the water-bearing aquifer was 0.5 million gal. By 1945 the quantity withdrawn

Jan 1, 1954

By J. E. Gould, H. J. Hand

Many independent studies are being made on slag-metal relationships in the open-hearth furnace, and these studies cannot help but result in an ultimate improvement in the quality of open-hearth steel of both the open and killed types. In maintaining quality control at the National Tube Company's plant, emphasis has been placed on an evaluation of the iron oxide content of the steel in as quantitative a manner as possible, in order that the most desirable level of oxidation might be obtained for a given type of steel, and to secure a more precise basis for final de-oxidation. In the past, various methods were used for estimating FeO content of the metal at tap to ensure uniform and thorough deoxidation of killed steel, avoiding overdeoxidation to minimize the amount of inclusions present and to make as sound a steel as possible. For the open-type steels, such control involves obtaining the necessary level of oxidation for the most suitable action of the steel in the molds to provide good surface quality and cross section for the specific grade involved. While rapid analytical methods are available for determination of FeO in the liquid metal, such methods are still not sufficiently rapid for routine control on the open-hearth floor, nor do such analyses provide information as to what causes high or low FeO values. The method of sampling can still be considered a problem in view of the variability encountered in taking simultaneous duplicate tests. With the accurate rapid methods now available for determining carbon in the metal, estimating slag basicity and obtaining temperatures of liquid metal, it was believed possible to determine the influence of the various furnace reactions in establishiug the state of oxidation at a given time. Simultaneous slag and metal tests were used in this analysis, aided by statistical methods, to determine the factors that affect the metal FeO, and also to make a quantitative evaluation of these factors. Data obtained are from actual iurnace operations, the metal test being of the I spoon, Herty type, and taken in duplicate. Metal temperatures were taken with the open-tube bath pyrometer developed by the Research Laboratory of the United States I Steel Corporation. This method of taking open-hearth metal temperature was invented by Collins and Oseland,l and was developed into its present form by L. 0. Sordahl,2 of the Research Laboratory. The instrument and its mode of operation have been fully described by Sordahl and Sosman in three publications.3,4,5 lag components were obtained by chemical analysis. Data were taken from four 165-net-ton furnaces during the working period of the heat. Recognizing that additions of ore affect the metal FeO. no tests were included within 30 min. after ore additions. In all, 65 tests (48 heats) were used in this study.

Jan 1, 1942

By J. E. Gould, H. J. Hand

Many independent studies are being made on slag-metal relationships in the open-hearth furnace, and these studies cannot help but result in an ultimate improvement in the quality of open-hearth steel of both the open and killed types. In maintaining quality control at the National Tube Company's plant, emphasis has been placed on an evaluation of the iron oxide content of the steel in as quantitative a manner as possible, in order that the most desirable level of oxidation might be obtained for a given type of steel, and to secure a more precise basis for final de-oxidation. In the past, various methods were used for estimating FeO content of the metal at tap to ensure uniform and thorough deoxidation of killed steel, avoiding overdeoxidation to minimize the amount of inclusions present and to make as sound a steel as possible. For the open-type steels, such control involves obtaining the necessary level of oxidation for the most suitable action of the steel in the molds to provide good surface quality and cross section for the specific grade involved. While rapid analytical methods are available for determination of FeO in the liquid metal, such methods are still not sufficiently rapid for routine control on the open-hearth floor, nor do such analyses provide information as to what causes high or low FeO values. The method of sampling can still be considered a problem in view of the variability encountered in taking simultaneous duplicate tests. With the accurate rapid methods now available for determining carbon in the metal, estimating slag basicity and obtaining temperatures of liquid metal, it was believed possible to determine the influence of the various furnace reactions in establishiug the state of oxidation at a given time. Simultaneous slag and metal tests were used in this analysis, aided by statistical methods, to determine the factors that affect the metal FeO, and also to make a quantitative evaluation of these factors. Data obtained are from actual iurnace operations, the metal test being of the I spoon, Herty type, and taken in duplicate. Metal temperatures were taken with the open-tube bath pyrometer developed by the Research Laboratory of the United States I Steel Corporation. This method of taking open-hearth metal temperature was invented by Collins and Oseland,l and was developed into its present form by L. 0. Sordahl,2 of the Research Laboratory. The instrument and its mode of operation have been fully described by Sordahl and Sosman in three publications.3,4,5 lag components were obtained by chemical analysis. Data were taken from four 165-net-ton furnaces during the working period of the heat. Recognizing that additions of ore affect the metal FeO. no tests were included within 30 min. after ore additions. In all, 65 tests (48 heats) were used in this study.

Jan 1, 1942

By G. A. Colligan, G. L. F. Powell

A new experimental technique has been developed to study nucleation behavior in eutectic alloys. It is somewhat similar to that applied by Sundquist and Mondolfo1 but with the advantages that: 1) bulk samples are undercooled instead of small droplets thus allowing the thermal behavior to be monitored by a thermocouple immersed in the sample, and 2) nucleation behavior is investigated in the same sample on either side of the eutectic composition by adding additional component to the sample under controlled conditions which preclude the addition of nu-cleation contaminants. Sundquist and Mondolfo carried out ]nucleation ex-periments on a large number of eutectic alloy sys-tems and concluded that nonreciprocal nucleation operated. If one phase a was a good nucleant for the other phase 0, then B was a poor nucleant for a. This was determined experinlentally by comparing the nucleation temperatures of 100 to 300 u diameter droplets of hypereutectic and hypoeutectic composition cooled from above the liquidus and from a temperature between the liquidus and the eutectic temperature. Primary phase a was concluded to be an efficient nucleant for the other phase B, if the following experimental result was obtained. Referring to Fig. 1, the temperature TI at which a drop of hypereutectic alloy of composition B froze when cooled from above the B liquidus was noted. This was the nucleation temperature for B in the absence of a. A drop of hypoeutectic alloy of composition A was then frozen from temperature T2 between the a liquidus and the eutectic temperature. The temperature T3 at which the eutectic nucleated in the presence of the primary or proeutec-tic a was noted. If this temperature T3 was higher than the temperature TI at which the B nucleated in a hypereutectic alloy, it was concluded that the primary a had nucleated the 6. This temperature T3, representing a certain undercooling below the equilibrium eutectic temperature Te , was designated ?TB by a> the undercooling below T, for nucleation of 13 by a. If there was no substantial difference in nucleation temperature between the hypereutectic drop cooled from above the /3 liquidus and the hypo-eutectic drop cooled from a temperature between the a liquidus and the eutectic temperature, it was considered that the a nucleated B at an undercooling equal to or greater than that at which P nucleated from a hypereutectic alloy. Sundquist and Mondolfo1 found that faceted primary crystals were good nucle-ants for metals that grow as orthogonal dendrites when present as the primary phase. Jackson2 has questioned Sundquist and Mondolfo's technique and proposed that in Sundquist and Mon-dolfo's samples, such as composition A, primary a retained B in reentrant grooves at their surfaces when heated to a temperature above the eutectic but below the a liquidus. This objection was suggested by experiments with organic eutectics where reten-

Jan 1, 1970

By H. W. Schadler

Single crystals of tungsten, which were grown by electron bombardment floating zone refining, were strained 2 pet in tension and bending at 298°, 77°, and 20°K to determine the modes and crystallography of the plastic deformation of these temperatures. At 77° and 20°K plastic deformation occurs by slip on systems of the type (011) [111] and by twinning on (112)-type planes. For crystals strained at 298°K, deformation occurs by slip in [111] directions on either (Oil)- or (112)-type planes. CURRENT models for the initiation of brittle fracture in crystalline materials are based on a knowledge of the details of their plastic deformation.1 Body-centered cubic tungsten exhibits brittle failure at temperatures below about 500 °K yet the modes and crystallography of its plastic deformation have not been studied below 1000°K. In 1924, Goucher2 reported that tungsten single crystals with a total impurity content of less than 0.01 wt pet deformed by slip on the (112) [111] system in the temperature range 1000° to 3000°K. He also observed (001) [010] slip in one crystal which was constrained by the presence of a large fissure. According to Barrett3 tungsten also deforms by twinning on the (112) plane in the [111] direction, but he gives no details on the tendency for twin formation or the temperature range in which twinning occurs. Therefore, as a necessary part of a study of the factors influencing the brittle fracture of tungsten, the modes and crystallography of the plastic deformation were determined at 298°, 77°, and 20°K. Tungsten single crystals, grown using the electron-bombardment zone-refining technique first described by Calverly,4 were deformed to between 1 and 2 pet plastic strain in tension and bending. The surface offset resulting from slip or twinning was observed with an optical microscope to determine the crystallography of the deformation. The existence of twins was proven by the standard polishing and etching technique; and the crystallography of dislocation motion was followed using the dislocation etchant described by Wolff.5 Some observations on the fracture characteristics of tungsten single crystals are included. EXPERIMENTAL TECHNIQUES Growth, Purity, and Perfection of the Crystals-Several years ago Calverly, Davis, and Lever4 dem-onstrated the feasibility of growing tungsten single crystals by the electron-bombardment floating zone-refining technique, and Carlson6 showed that crystals produced in this way had a high degree of purity and were ductile at room temperature. Tungsten single crystals produced by this technique in equipment similar to that described by Carlson were used in this study. The starting material, a powder metallurgy product, was obtained in the form of a swaged 1/8-in. rod from the General Electric Wire Plant in Cleveland, Ohio. The crystals were grown from this material in a vacuum of 10"4 mm of Hg by passing a molten zone 1/8 in. long down the rod twice at a speed of 3 mm per min. At this zone speed

Jan 1, 1961

By J. W. Marx

A method is given for predicting the complete gravity drainage characteristics of arbitrarily long columns from centrifuge drainage measurements on reconstituted core samples. Oil residuals corresponding to hundreds of years of normal gravity depletion can be obtained in a few hours on the centrifuge. The gravity flow rate at any stage of the depletion process may be determined from the time correlation derived, and experimentally checked, in this study. INTRODUCTION Apart from the original observations of Muskat et al1, research publications2,3,4 on the subject of gravity drainage have been largely concerned with establishing in detail the saturation, S as a function of the height, z, in a draining column at any given time, t. Some form of numerical integration must be employed to obtain production rates and cumulative production even when S(z, t) is known. Furthermore, the relevant experimental work has been concentrated on drainage of a single wetting liquid from unconsolidated media. Since oil production usually concerns the drainage of a partially wetting liquid from consolidated media, in the presence of connate water, and since it is unlikely that sufficient information exists to establish S(z, t) in detail for any natural reservoir, the published research work appears to be, at best, only qualitatively applicable to production problems. With this in mind, the present study was undertaken by the writer. Experiments were planned whose results would have two advantages over existing measurements: 1. Observations were to be made on specific reservoir rock, reconstituted with formation water and formation oil. This would reduce their generality, from the research viewpoint, but increase their utility for production purposes. 2. The measurements were to be self-integrating, i.e., the phenomena were to be described and interpreted in terms of cumulative results. THEORETICAL DEVELOPMENT It was commonly known that centrifuging a liquid bearing porous medium increases the drainage rates and minimizes capillary end effects. The specific problem lay in selecting an acceleration, a, such that the mean residual saturation of a model cylinder was equal to the residual saturation of an arbitrarily long prototype column when the latter was drained by earth gravity alone. The physical conditions required to permit a valid scaling of model drainage time, tm with prototype drainage time, t, may be stated as follows: (a) At t = tm = O, So = Smo; (b) At t = tm? 8 Sr. = Smr.; (c) For all intermediate values of t and dS/dt=dsm/dtm whenever S = Sm; (d) S(z) = Sm(z) = a constant when t = tm = 0. 1 Here S = T I S(z)dz, where h is the length of the « Jo cylindrical column being drained and the subscripts S,Sm, and refer to model, initial, and residual systems, respectively. The first three conditions mean, simply, that an 3 vs t plot will be numerically identical with an S, vs t, plot,

Jan 1, 1957

By George A. Morrison

A deposit Of limestone Was known to exist at a depth of 2000 ft under the property of the Columbia Chemical Division of the Pittsburgh Plate Glass Co. at Barber-ton, Ohio. A 662-acre site was selected for the projected mine, some two miles northwest of the plant and near the main line of the Erie Railway. An electric railway 8800 ft in length connects the mine and the plant. The deposit is overlain by 18 ft of un-consolidated (sand and gravel), 100 ft of water-bearing sandstone, and finally 2080 ft of shale into which thin layers of sandstone are embedded. The limestone bed itself is 345 ft thick and overlies 200 ft of gypsum. A 300-ton-per-hour capacity mine was decided upon. Two shafts were deemed advisable, one for production and the second for service; and these were sunk 550 ft apart, one to a depth of 2323 ft and the other to 2258 ft. Each is 16 X , ft in the clear and timbered with 6-in. steel H-sets on 8-ft centers, using 3/8 X 4 X 4-in. angles as studdles. Twelve inch I-beams were used at 160 ft intervals as bearers set in deep hitches and concreted to a vertical depth of 8 ft. Wooden sheathing was first employed but sloughing of the shale created a pressure on this lining and finally concrete was deemed necessary. Water was encountered only within the first 315 ft, flowing at 60 gpm and by grouting this was reduced to 15 gpm. Temporary wooden sinking headframes were installed with 300 cu ft capacity storage pockets and with doors automatically controlled by air cylinders by hoistmen. Each shaft was operated on four 6-hr shifts. The usual V-cut was drilled at the center of the shaft and the round consisted of 34 holes- A 40 pet gelatin dynamite was employed with some 60 pet in the cut holes. Drilling crews consisted of four to six men. Shale drilled easily but became more bed in depth and sandstone wore away the gauge Of the bits rapidly. A room-and-pillar mining system was adopted whereby rooms turned off on 80-ft centers, each room 40-ft wide and 50-ft high. Rib pillars between rooms were cut into 100 ft lengths by frequent holes. Ventilation is achieved through the two shafts, the down-draft through the service shaft, and the return through the pr0duction shaft. The hoist has a a Of 300 tons per hour and is equipped with 10-ton balanced skips requiring. a 2-min cycle Or 30 trips Per hour- Hoisting is designed to Operate by automatic loading and no hoistman is required for normal Operation. The 48 X 60 in. jaw primary crusher is underground. It is fed through chute and chain feeders and is flood-oil lubricated and cooled. An inclined belt conveyor returns oversized material to the crusher. Tramming is by Diesel-powered trucks.

Jan 1, 1948

By George A. Morrison

A deposit Of limestone Was known to exist at a depth of 2000 ft under the property of the Columbia Chemical Division of the Pittsburgh Plate Glass Co. at Barber-ton, Ohio. A 662-acre site was selected for the projected mine, some two miles northwest of the plant and near the main line of the Erie Railway. An electric railway 8800 ft in length connects the mine and the plant. The deposit is overlain by 18 ft of un-consolidated (sand and gravel), 100 ft of water-bearing sandstone, and finally 2080 ft of shale into which thin layers of sandstone are embedded. The limestone bed itself is 345 ft thick and overlies 200 ft of gypsum. A 300-ton-per-hour capacity mine was decided upon. Two shafts were deemed advisable, one for production and the second for service; and these were sunk 550 ft apart, one to a depth of 2323 ft and the other to 2258 ft. Each is 16 X , ft in the clear and timbered with 6-in. steel H-sets on 8-ft centers, using 3/8 X 4 X 4-in. angles as studdles. Twelve inch I-beams were used at 160 ft intervals as bearers set in deep hitches and concreted to a vertical depth of 8 ft. Wooden sheathing was first employed but sloughing of the shale created a pressure on this lining and finally concrete was deemed necessary. Water was encountered only within the first 315 ft, flowing at 60 gpm and by grouting this was reduced to 15 gpm. Temporary wooden sinking headframes were installed with 300 cu ft capacity storage pockets and with doors automatically controlled by air cylinders by hoistmen. Each shaft was operated on four 6-hr shifts. The usual V-cut was drilled at the center of the shaft and the round consisted of 34 holes- A 40 pet gelatin dynamite was employed with some 60 pet in the cut holes. Drilling crews consisted of four to six men. Shale drilled easily but became more bed in depth and sandstone wore away the gauge Of the bits rapidly. A room-and-pillar mining system was adopted whereby rooms turned off on 80-ft centers, each room 40-ft wide and 50-ft high. Rib pillars between rooms were cut into 100 ft lengths by frequent holes. Ventilation is achieved through the two shafts, the down-draft through the service shaft, and the return through the pr0duction shaft. The hoist has a a Of 300 tons per hour and is equipped with 10-ton balanced skips requiring. a 2-min cycle Or 30 trips Per hour- Hoisting is designed to Operate by automatic loading and no hoistman is required for normal Operation. The 48 X 60 in. jaw primary crusher is underground. It is fed through chute and chain feeders and is flood-oil lubricated and cooled. An inclined belt conveyor returns oversized material to the crusher. Tramming is by Diesel-powered trucks.

Jan 1, 1948

By S. R. Goodman, Hsun Hu

The rolling texture transition in copper as a function of deformation temperature is found to be quite similar to that in high-purity silver. The ordinary copper type texture changes gradually to the brass type, accompanied by an increase in the stacking fault frequency, as the temperature of deformation decreases. The rolling textures obtained at low temperatures and the corresponding annealing textures compare remarkably well with the ordinary rolling and annealing textures of low-zinc brasses. Furthermore, it is also found that the observed stacking fault energies of copper specimens deformed at low temperatures correspond closely with those of low-zinc brasses, as deduced from measurements of the dislocation nodes. These results are consistent with the idea that texture transition may be significantly dependent on the stacking fault energy. It was shown in a series of previous publications1"3 that the rolling texture of high-purity silver changes gradually from the common silver type (or the brass type) to the copper type* with increasing temperature *The silver or brass type rolling textures are commonly described as (110)[112],4,5 whereas the copper type rolling textures are mainly (123) [a121 and (146)[211].5 Other ideal orientations have been used by various investigators for the copper type rolling textures, but the actual difference among these ideal orientations is rather small. of deformation, and that such texture transition can be correlated with the change in stacking fault frequency as a function of rolling temperature. Furthermore, it was shown that the formation of annealing textures in high-purity silver from the various rolling textures obtained during the course of texture transition depends entirely upon the deformation texture. From a common silver type or brass type rolling texture (such as produced by rolling at 0" or at 50° C) the recrystallization texture is mainly (120)[211], which is quite different from the recrystallization texture of brass.* However, for both ma- terials the orientation relationship between the rolling texture and the recrystallization texture can be expressed in terms of similar rotations around [Ill.] axes of approximately 30 or 35 deg. They differ in that the [Ill] rotational axes are different. In the case of high-purity silver, the axes of rotation are the two (111) poles near the plane normal of the deformed specimen with a (11l)[112] type rolling texture, whereas in brass, they are the (111) poles near the direction of rolling. For high-purity silver with a predominantly copper type rolling texture (such as produced by rolling at 150° or 200°C) the recrystallization texture is mainly (100)[001], or the cube texture, plus its twin orientations. It was shown previously6 that such reorientation observed in copper or aluminum can be described as [Ill] rotations of 30 to 40 deg. For intermediate cases, i.e., when the rolling textures are composed of a

Jan 1, 1963