Search Documents

By George C. Ference

Sulfur is the 13th most common element in the earth's crust, constituting approximately 0.05% of the total. It occurs naturally in its elemental form, as metallic sulfides, nonmetallic sulfates, and as combined or free sulfur in natural gas, crude oil, and coal. COMMERCIAL SOURCES Most of the sulfur that is consumed is converted into sulfuric acid before use; therefore, it is not necessary to recover sulfur solely in its elemental form. Processes for recovery are peculiar- to the types of reserves being processed. The major commercial processes as well as the general geographic locations where the appropriate reserves occur are listed in the following. It should be noted that the sulfur values may be recovered as the primary product, as a coproduct with other materials, or as a byproduct. Elemental Sulfur 1) Frasch mining is used for subterranean deposits of elemental sulfur around the Gulf Coast areas of the United States and Mexico. Generally, but not exclusively, such deposits are located in salt dome structure. 2) Autoclaving, flotation, or solvent extraction of surface deposits of elemental sulfur is practiced throughout the world. 3) Extraction and conversion of hydrogen sulfide from sour natural gas into elemental sulfur is done principally in Canada, France, and the United States. 4) Conversion of metallic sulfides from pyrites into elemental sulfur is done via the Outokumpu process in Finland. 5) Catalytic cracking and hydrocracking of sulfur-bearing crude oils to produce elemental sulfur is done worldwide. Desulfurization of refined petroleum products also yields elemental sulfur. 6) Recovery of elemental sulfur from sulfur-bearing oil sands (Athabasca tar sands) has been initiated in Canada. 7) As of this writing (1970), a plant has been constructed for the thermal decomposition of gypsum to produce elemental sulfur in the United States. Sulfuric Acid Sulfur values in the form of sulfuric acid are recovered via: 1) Recovery from smelter gases throughout the world. 2) Roasting of pyrites throughout the world with iron sinters as a byproduct. 3) Roasting of anhydrite with cement as a coproduct, primarily in Europe. 4) Processes currently are being developed for recovery of sulfuric acid from combustion gases resulting from the burning of high-sulfur-content fuel. Other Sulfur values also are recovered from waste products which normally occur in highly industrialized areas. Some examples are: coke-oven gases, sludge sulfuric acid, and pickling liquors (ferrous sulfate).

Jan 1, 1976

The Ashanti mine is located in the Gold Coast region of West Africa in Ghana, where gold is found over a wide area of about 105,000 sq km (40,000 sq miles). Ashanti has been the most productive of all the lode mines and has been one of the world's notable gold producers for over 50 years. The mine is located at Obuasi, 113 km (70 miles) north and east of Tarkwa, which is 80 km (50 miles) inland from the coast. The Ashanti lode is worked on 300 m (1,000 ft) of strike length over a width of 12 m (40 ft), and by 1934 it had attained a depth of 700 m (2, 300 ft). The lode is in pre-Cambrian granite intruding a system- of shists, phyllites, etc., containing fragments of the wall rock with quartz, carbonates, sericite and small amounts of pyrite, arsenopyrite, sphalerite, galena, and gold. The shattered quartz fractures carry sulfides and gold, most of which are invisible. (William Harvey Emmons, "Gold Deposits of the World," McGraw -Hill, 1937.) Because the mill treats an ore composed of refractory sulfides - chiefly arsenopyrite and fine free gold - the flowsheet reflects the complex ore characteristics. Plane tables are used in the grinding, circuit for free gold recovery. After roasting the sulfide flotation concentrates, additional free gold is recovered from the calcines with a rotary belt concentrator and the two concentrates are combined for feed to the amalgamation pans, with the resulting gold amalgam being retorted. Following four-stage crushing to minus 9. 5 mm (318 in.) with two stages of grinding, the cyclone overflow is floated for sulfide recovery. The flotation concentrate is roasted with the calcine reground and roughly cyanided to scalp out the gold readily dissolved in one of two cyanidation circuits. The cyanide residue joins the thickened flotation tailing for cyanidation in a complete CCD circuit using filters. The gold precipitates are calcined before melting in pot-type furnaces. The tonnage to the mill of 3,175 mtpd (3,500 s tpd) with a content of over 14.7 g per mt (0.43 oz per st) places the Ashanti production as one of the top producers in the world; and with its past long life, the total production rates it as one of the world's great mines.

Jan 1, 1981

By Porter W. Shimer

As is well known, cast-iron borings are a mixture of small particles of iron with more or less of finely divided graphite, separated from thc surfaces of these small particles during the process of boring. The amount of graphite thus mechanically mixed is, in all cases, quite large enough to cause serious difficulty when the problem is to obtain an average sample of a given lot of borings for carbon determination. This difficulty arises from the necessity of obtaining a uniform mixture of the heavy and comparatively coarse borings with the finely divided and light graphite, and of removing a sample for analysis without disturbing the uniformity of this mixture. It was first sought to overcome this difficulty by having the horings made very fine, so that they might have more nearly the size of the particles of graphite. It was not practicable, however, to secure this uniformity of size, since much of the graphite is in the form of the finest dust. At all events, the duplicate determinations of rarbon in these fine borings, made with every precaution by combustion in oxygen, frequently showed differences too large to be accounted for in arty other way than by imperfect sampling. Very coarse borings were also tried with the idea that the graphite separated from these large and heavy pieces would perhaps be inappreciable ; but it was found that quite enough was separated to vitiate the results. Various methods of mixing were tried, both in the bottle and on glazed paper ; but in all these mixtures it mas found that duplicate samples seldom colitained the same proportion of the mechanically mixed graphite; and when they did, there could be no certainty that it was the true proportion. All this was shown many times over by the failure of duplicates to agree closely, the differencheing sometimes so much as 0.20 per cent. It was finally clear that nothing was to be hoped from these methods. Even if we could secure a perfect mixture containing in every part its due proportion of graphite, it would run a great risk of being destroyed the moment a spatula was inserted to remove a sample: for the least agitation causes some of the graphite to fall through between the coarser borings.

Jan 1, 1886

By W. Rostoker

A STUDY of the titanium-oxygen system' involved an associated series of measurements of the lattice parameters of the a and TiO phases. The results permit some interesting deductions which are herein reported. A comprehensive survey of the physical PI-operties of the phases in this alloy system has been made by Ehrlich.2 However, only impure titanium was available at that time, so that some revision of his measurements is to be expected. The lattice parameters were calculated from the high angle lines of Debye-Scherrer patterns taken in a 14 cm camera and using filtered CuKa radiation. The specimens were prepared largely by crushing and screening of lump samples which had been quenched from elevated temperatures. Only in the case of low oxygen contents was it necessary to resort to filing and annealing. The results of the lattice parameter studies are graphically presented in Figs. 1 and 2. It will be seen that oxygen produces a pronounced distortion of the c parameter of the a phase (hexagonal close-packed). The trend is in general agreement with Ehrlich's work, although the divergence of actual parameter values strongly suggests that his titanium was very impure. It will be noted that the a phase of titanium can tolerate the unusually high saturation solubility of about 34 atomic pct 0. By virtue of this unique effect, it is possible to make a calculation of the effective atomic diameter of oxygen when dissolved in a lattice with metallic bonding. This has not been possible before. Ehrlich's2 density measurements demonstrated that oxygen occupies interstitial positions in the a lattice and the trend of the lattice parameters would certainly support this. In a hexagonal close-packed unit cell the largest interstitial positions lie at (2/3, 1/3, 1/4) and (2/3, 1/3, 3/4). Accordingly, if both of these positions were occupied, the ratio of titanium to oxygen would be 1:1. The extrapolated c parameter may be taken as between 4.93 and 4.99?. The a parameter appears to reach a constant value of 2.955? at low oxygen contents. The distance of the center of a titanium atom site from the [vc2/16+a2/3-1.448] Then the atomic diameter of the oxygen atom is represented by the function: where the radius of the titanium atom is 1.448A,

Jan 1, 1953

By Lester Guttman

THE connection between short-range order and thermodynamic activities in binary solid solutions has been pointed out by Birchenall1 who calculated approximate values of the energy of interaction of Zn and Cu and of the degree of short-range order in alpha-brass at one composition and two temperatures. The purpose of this note is to call attention to a somewhat more accurate theory than that used by Birchenall and to extend the calculations to a wider range of temperatures and compositions as a means of testing its applicability. This is an example of the well-known general method of comparing measured thermo-dynamic functions of a system with those calculated from a microscopic model by means of statistical mechanics. In this case, mathematical approximations must be used which make difficult any decision about the validity of the model. Birchenall's statistical method resembles closely that called by Fowler and Guggenheim2 the "quasi-chemical" method which has been shown to lead in certain cases to results identical with those obtained by the method of Bethe.3 The quasi-chemical method has been extended by Takagi4 to give general formulae for the free energy of binary solid solutions based on several lattices at all compositions and temperatures. Specifically, he treats the four systems typified by: I. ß-brass; 2. a- brass; 3. AuCu3; 4. AuCu. When the temperature is so high that no long-range order exists, these formulae reduce to the same form for all lattice types, namely: [ ] Here the symbols have the following meanings: [F-Helmholtz free energy E-energy S-entropy k-the gas constant per molecule z-coordination number, (e.g. 12 in. a-brass). N-total number of atoms c-atomic fraction of A] VAA, VBB, VAB-energy per bond of the corresponding bonds log means log, throughout The superscript 0 denotes the thermo- dynamic function in the standard state, which has been chosen to be pure A or B with the same crystal structure as the solid solution. The quantity x is the ratio of the number of A-A bonds to the total number and for minimum F satisfies the equilibrium condition [ ] The free energy may also be written in terms of µA and µB, the chemical potentials or partial free energies per atom:

Jan 1, 1948

By J. J. Frawley, W. J. Childs

PREVIOUS studies have shown that if a supercooled liquid metal was perturbed by vibration the probability of nucleation is is During a recent investi- gation to determine quantitatively the amount of energy needed to cause nucleation in a given supercooled liquid specimen, it was found that at low-energy values in the megacycle range, below the threshold energy value for cavitation, the amount of dynamic supercooling was greater than the amount of static supercooling. That is, if a specimen had a given amount of thermal supercooling under static conditions, its thermal supercooling could be increased by the addition of low-energy sound waves. The material used in this investigation was high-purity bismuth. This material was chosen because of its low melting point and the high degree of supercooling which could be easily obtained. The sound gener- ator employed in this work was a commercially built Sperry ultrasonic testing unit. This unit was equipped with a barium titanate crystal as a piezoelectric transducer. These sound waves were transmitted to the supercooled melt by a Pyrex rod, as shown in Fig. 1. The transducer was coupled to this Pyrex rod wave carrier by motor oil. The Pyrex wave carrier was approximately 1.5 ft long to prevent damage to the transducer by heat. The diameter of the Pyrex wave carrier appears to be critical. In the initial tests a wave carrier of 0.5 in. in diam was employed. However, the sound waves had no effect on the amount of dynamic supercooling. When the diameter of the wave carrier was increased to approximately the inside diameter of the Pyrex crucible, the sound waves were more effective. Approximately 200 g of metal was melted under a stannous chloride flux in a 30-ml beaker by induction heating. The temperature was recorded by a Pyrex-encapsulated chromel-alumel thermocoule which was placed in the beaker after the bismuth melted. The Pyrex wave carrier was immersed slightly below the surface of the liquid bismuth and the specimen was reheated to about 500°C. It was observed that the amount of supercooling depends on the amount of superheating the specimen receives; therefore, for meaningful results the amount of superheating was the same for all heating cycles. The specimen was allowed to cool in air and the change in temperature was continuously monitored with a potentiometric strip-chart recorder.

Jan 1, 1969

By L. F. Rooney

In June 1964 the Indiana Geological Survey discovered gypsum beds more than 10 ft thick in rocks of Devonian age in La Porte County, Ind. Although the extension of the Michigan Basin evaporites into northern Indiana has been recognized for some time, the gypsum beds have been regarded as either too thin or too deep for exploitation. Current Survey research, however, indicates that exploration by industry might find commercial deposits of gypsum less than 50 miles from Chicago. In four cores taken by the Survey within 1 sq mile in La Porte County, the maximum thickness of inter-bedded gypsum and anhydrite is 35.8 ft. Both gypsum and anhydrite beds contain irregular masses of limestone and dolomite that average a few inches in cross section and total about 20% of the rock by weight. The maximum thickness of gypsum in one minable unit verified by core is 12.5 ft, and its purity is 81.3%. Chloride content of the gypsum beds is less than 0.005%. Depth to the gypsum in La Porte County is 330 to 500 ft, about the same depth as the gypsum being mined in Martin County, Ind. In June 1964 the Indiana Geological Survey discovered gypsum deposits of probable commercial thickness near La Porte, Ind. (Fig. 1). This article presents preliminary data on the distribution, thickness, depth and chemical composition of the gypsum, the possible causes of gypsification, and economic considerations of immediate interest to industry. Because of the preliminary nature of the work, only a few geologic relationships concerning the genesis of the deposits will be mentioned. DEFINITIONS The following terms used throughout this article have been restricted to the following definitions: evaporites: anyydrite (CaSO4) or gypsum (CaSO4 . 2H2O). minable evaporites: any evaporite unit which may contain more than 80% evaporites, which is more than 10 ft thick, and which in places may be completely gypsified. PREVIOUS WORK The presence of gypsum and anhydrite in the Devonian rocks of northern Indiana has been recognized for at least 70 years1-4 and can be inferred from a number of reports on the geology of Michigan. For example, in a cross section from southwestern to central Michigan, Ells5 indicated the presence of

Jan 1, 1965

Discussion of the paper of E. C. HARDER, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2573 to 2586. I. C. WHITE, Morgantown, W. Va.-I have seen some of the great iron-ore deposits described in this paper. -One of these in the State of Minas Geraes appears to be an immense mountain of iron ore about 2,000 ft. in height. All over its surface from bottom to top may be seen large masses of rich iron ore, varying in weight from a few pounds to several tons, and from all that one can judge without exploitation, the quantity of available ore is certainly very large in this particular mountain. Whether it will prove a mere surface deposit or shell, like the famous Iron Mountain of Missouri, is for future exploration to determine. The question of transportation is the main factor in determining the availability for exportation of these Brazilian iron ores. There is no coal in Brazil that can be manufactured into coke without expensive previous treatment, since the best of the raw coal in the States of Rio Grande do Sul, Santa Catharina, and Parana, contains about 35 per cent. of ash, of which about 6 per cent. is sulphur, and coal of this composition cannot be utilized in iron smelting without purification. When I was chief of the Brazilian Coal Commission in 1904 to 1906, I had a cargo of this coal shipped to Balk, Germany, and treated in the great coal-testing plant of the Humboldt Engineering Works, located just across the Rhine from Cologne. It was found that by crushing and washing the Brazilian coal, it yielded 33 per cent. of briquetting coal, containing only 10 to 12 per cent. of ash (of which 1 per cent. was sulphur), and 42 per cent. of slack coal, with 25 per cent. of ash and low in sulphur, so that about 33 per cent. of the Brazilian coal could be converted into coke of fair quality, as shown by the following average of three analyses, using air-dried coal, of briquets made from the Barro Branco coal bed, State of Santa Catharina: Moisture 1.56 Volatile matter 31.66 Fixed carbon 56.73 Ash : 10.05 Total 100.00 Sulphur 1.34 Phosphorus 0.003 B.t.u 13,395

Jan 4, 1915

By R. J. Murphy, N. J. Grant, J. W. Dowding

A large number of blast furnace slag-metal tests were examined to determine if the manganese reduction could be used as a primary indicator of the degree of oxidation or reduction of the slag and of its desulphurizing power. Slag basicity and temperature were also evaluated. Two laboratory heats were made and sampled prior to reaching equilibrium to check blast furnace data. IN a recent investigation of the factors affecting desulphurization in the blast furnace, is was evident that manganese reduction appeared to parallel the course of desulphurization. Grant, Kalling, and Chipman1 pointed this out in a series of time studies utilizing closely controlled laboratory melts. Fig. 1 is a composite plot of sulphur removal and manganese reduction as a function of time under two slags of different basicity. Manganese reduction appears to approach equilibrium at approximately the same rate as does sulphur. It was also demonstrated that the addition of oxygen to the slag, as manganese oxide, caused a sharp reversal of sulphur from the slag to the metal.' It has been shown that "Excess CaO" was a primary factor in measuring the degree of desulphurization under ideal reducing conditions,1,2 the following reaction being representative of the process: CaO (slag) + S + C (solid) = CaS(slag) + CO (gas) It was also evident that a second reaction could drive the sulphur from the slag into the metal. A suggested reaction was' CaS (slag) + 0 = CaO (slag) + S Any change in the oxidizing power of the system would thus affect both the sulphur and the manganese without causing any change in the calculated basicity of the slag. "Excess CaO," "Excess Base," and other similar basicity values, under such oxidizing conditions, would therefore not be the best measure of desulphurizing power; instead, as was shown by and Chipman" he oxygen content of the slag at low oxygen levels would be the controlling factor. Unfortunately, the extent to which FeO is reduced in the blast furnace makes it difficult to utilize slag FeO as an accurate indicator of the degree of oxidation. By comparison, manganese reduction in the blast furnace proceeds more slowly and is generally only about 40 to 70 pct complete. manganese, which is present in significant amounts and is readily analyzed, offers an opportun-

Jan 1, 1954

By E. E. Barker

Although flotation was known to be a successful process prior to 1312, Utah Copper Co.'s ores were not entirely treated by this process until 1923. Experiments had been conducted, of course, prior to that time, and in February, 1917, the first unit of the Arthur plant was changed over from gravity concentration to flotation. On May 16, 1918, the entire Arthur plant was on flotation, excepting the coarse concentrate which was tabled prior to fine grinding. The reasons for the delay in adopting flotation at these plants were, first, that it was decided to await the outcome of the litigation with the Butte & Superior Mining Co., which began with an injunction served on Oct. 3, 1911. This litigation continued for years. Then the demands on the plants in the war years 1916, 1917 and 1918, really precluded any further drastic changes during that period, as all efforts were bent on maximum tonnage, and the cry of tonnage, rather than of recovery, was the major issue. The postwar depression followed these years of intensive production, so that it was not until 1922 that the Magna plant was equipped to use this process. Excepting, then, the amount of coarse concentrate that was tabled, 1923 was the first year when the Utah Copper Co.'s ores were on a full flotation basis. Effect of Flotation on Ore Reserves The object of this paper is to point out the effect that flotation has had on the operations of the Utah Copper Co. In 1905, when D. C. Jackling began making history in copper, the ore reserves were 34,000,000 tons, with a grade of 2 per cent. copper and a mill capacity of 700 tons daily. The point of cut-off between nonprofitable and profitable grades was 1.2 per cent. A few years later the capacity was increased to 6000 tons, when 1.1 per cent. became the point of cut-off. Ore reserves had climbed to 80,000,000 tons, having a grade of 1.9 per cent. In 1911 there was an ore reserve of 300,000,000 tons, with a grade of 1.5 per cent. and a cut-off of 1 per cent.; in 1918 the ore reserve was approximately 400,000,000 tons, and a grade of 1.38 per cent., and point of cut-off 0.95 per cent., based on normal costs and prices. Up to this

Jan 1, 1928

By R. A. Bergier

The Transactions of the Institute contain nothing, as yet, on the subject of pocket-compasses; and in the belief that American miners, explorers, geologists, and engineers will gladly welcome any infor mation about new forms of apparatus, simple in construction and adapted to rapid use, I offer a short description of an improved French combination pocket-compass, which, if once introduced into use, would seem likely to supersede similar instrumens of older pattern. The instrument in my possession I owe to the kindness of M. G. de.La Bouglise, of Paris. The frame of the compass is a double-bottomed box, 2 1/2 inches square and 9/16 of an inch high, made of white metal, and with its sur faces very carefully planed. The sides of the box make true right angles with each other. Two sides are parallel with, and two are normal to, the north and south line of the principal graduation. The bottom is accurately planed, so that the instrument will lie true on a plane surface. A glass, 2 3/8 inches in diameter, is set in the top plate. The graduation for the needle is engraved on the upper face of a ring, connected with the flat disk, in which the center-pin is in serted. Between this disk and the bottom of the box there is a hollow space a quarter of an inch deep. The needle is 1 7/8 inches in length, and can be balanced by means of a small sliding piece of metal. The graduation extends from 0° to 360°, reading from right to left. The stopping of the needle is effected by a screw, A, on the side of the box near the handle, H (Fig. 1). There is also a clinometer attachment, the graduation for which is engraved on the upper face of the silver-plated disk. The compass has two sights. The north sight, B, is a simple pin, a little more than an inch high, which, when not in use, is kept folded down, and is partially protected by the exterior sliding-plate, C. When raised for use, the sight is stopped in a vertical position by a projecting pin attached to the side of the box.. The south sight, D, is connected with the handle, H, and the sight and handle

Jan 1, 1890

By J. M. Lommel

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,' and Hess and Cieorge.' Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on 'Microcloth' using a lubricant of 'Hyprez' oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the 'Microcloth' nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80o to 90°C. The cream is allowed to cool, and is then 'whipped' to a smooth consistency with 100-ml 'Hyprez' oil. Before polishing, the diamond loaded 'Microcloth' is moistened with a few drops of 'Hyprez' oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- µ diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By T. H. Alden

In several recent studies of fatigue fracture in single-phase metals, tests have been made using the condition of essentially constant plastic strain amplitude.1-4 This procedure departs from the more common practice of holding the amplitude of stress constant. From these studies have emerged two important generalizations about the behavior of metals during cyclic straining. First, measurements of the stress amplitude, required to impose the fixed plastic strain amplitude, have shown that the rate of cyclic strain hardening in annealed metals is rapid in the early cycles but decays quickly to a very low value.1"5 This behavior is displayed particularly for a range of strain amplitudes below about 2 pct and at low and high temperature. Frequently, the hardening rate becomes so low that one can determine a "saturation" stress. This stress increases with strain amplitude. In addition, an experimental relation between fracture life and plastic strain amplitude was obtained by Coffin and Taternelli,' namely N 1/2 ep = constant. For several metal:;, this equation has been shown to hold down to a strain amplitude of 0.1 pct. Whether it also holds in the "low amplitude" range (lives of more than about 105 cycles) has not been established. The importance of the saturation stress level (a value derived from strain hardening measurements) to the question of fracture life (the usual quantity of interest of fatigue testing) lies in the observation that cracks start to form when the cyclic hardening rate is essentially zero, and not before.4"5 This point suggests immediately a means of relating tests at constant stress and constant strain amplitudes. When making comparison, the stress in a constant stress test is to be identified with the saturation stress in a constant strain test. If these ideas are correct, then it should be possible, using the relation between fracture life and strain amplitude and experimental curves of saturation stress versus strain amplitude, to predict the fracture life as a function of stress, i.e. predict the S -N curve, for low stress fatigue. Saturation stress amplitude-plastic strain amplitude data, obtained in tension-compression, exist only for a few metals and for relatively high amplitudes of strain. Comparable S -N curves (push-pull loading) were known by the author only for OFHC copper. Values for this metal taken from Ref. 2 are shown in Fig. 1. The strain amplitudes, the lowest

Jan 1, 1962

By S. D. Baumer, P. M. Hulme

B. M. Larsen (U. S. Steel Co., Kearny, N. J.)—Could we have some sort of an estimate on the cost of calcium carbide for this treatment? Also, if you used calcium carbide on carbon-saturated iron, would some effect hold back the reaction? P. M. Hulme (authors' reply)—As far as I know we have not worked on carbon-saturated iron. About 3½ pct C is the highest we have worked on. As far as cost goes, it depends on how much sulphur You have to take out. It will run anywhere from $0.75 to $2.00 a ton overall cost including the cost of carbide per ton of metal treated. That is, using the efficiencies that we show in this paper. We are getting better efficiencies now. T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—Did you say 2 lb of calcium compound? Mr. Hulme—That is based on 10 lb of calcium carbide per lb of sulphur removed. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—We have run this type of desulphurization process at the blast furnace. We have desulphurized between 100 and 200 at the blast furnace and taken the iron right out of the furnace with an injector system. The process gave us quite varied results; stratified iron, high sulphur on the top and low sulphur on the bottom, and we decided it was impractical. Mr. Hulme Just what was the type of injection equipment? Dr. Babcock—Nitrogen gas for one injection method and we used fairly large gun equipment. We followed the same general type of pattern you show only on a larger scale. Mr. Hulme—It sounds very much like what we call the gale of wind method. We have very erratic results with that. Dr. Babcock—We have tried several types, and particle sizes. The operation was not satisfactory. Mr. Hulme—Of course, we have never tried it on that scale except on a continuous basis. That is the reason we abandoned the idea of working on 35 ton ladles on a batch principle and took it as it came out of the cupola and treated it on the fly on a continuous basis. Dr. Babcock—When you compare the relative effectiveness of the process as carried out, it does not give a very favorable comparison of that process which is already developed. We did not feel it was worth the

Jan 1, 1952

By R. T. Pepper

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,' and Hess and Cieorge.' Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on 'Microcloth' using a lubricant of 'Hyprez' oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the 'Microcloth' nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80° to 90°C. The cream is allowed to cool, and is then 'whipped' to a smooth consistency with 100-ml 'Hyprez' oil. Before polishing, the diamond loaded 'Microcloth' is moistened with a few drops of 'Hyprez' oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- ° diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By K. Nassau

The Effect of tin and hydrogen on the C0 parameter of a titanium. specimens were capsule cooled in water to eliminate contamination by water. Deybe-Scherrer photograms were obtained in a 114.6 mm camera with CuKa radiation. The parameters shown in Table I and Fig. 1 were calculated from the 213 (8569°) and 302 (8173.5°) reflections? no attempt being made to correct for systematic errors. The principal difference in method of preparation of specimens between this investigation and that of Worner was the use of pickling by the latter to produce X-ray diffraction samples. The possibility that hydrogen introduced by pickling was responsible for the lower a and c-parameters was investigated with the same 80 pct HNO3- 20 pct HF solutions used by Worner. The 6 and 10 at. pct specimens, the parameters of which had already been determined, were pickled and the c-parameters obtained are also shown in Fig. 1. The a-parameters, not shown, are also diminished. The quality of the lines obtained from the unetched and etched samples was unchanged, being quite sharp in both cases. It is quite possible that if corrections for systematic error carried out that the parameters obtained for the unetched samples would approach the data of Worner. In any event, the parameters of the etched samples would be still lower. The data obtained here is evidence that hydrogen in solution has contracted the c and a -parameters. Crystallographic Angles of Calcium Tung-state (Tetragonal, c/a = 2.169) K. Nassau In connection with the preparation and orientation of single crystals of calcium tungstate (Scheelite -CaWO4), the need arose for a stereographic projection for this tetragonal material. There appear to be no tetragonal projections with a c/a ratio above that of indium1 (c/a = 1.522) in the literature. In addition to its use for calcium tungstate, such a projection might find other more general applications and is accordingly presented below. The most recent X-ray diffraction work on CaWO4 is that of Swanson, Gilfrich, and Cook,2 where a summary of previous work is also found. Lattice parameters given are: a = 5.242A, c = 11.372A, and c/a = 2.169. The material is tetragonal with space group Table I, giving angles between crystallographic planes (HKL) and (hkl), was calculated from the formula3

Jan 1, 1961

By D. A. Dahlstrom

In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in [Fig. 4]. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in [Fig. 4]. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensers, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89c/t (81c per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed.

Jan 1, 1984

By W. Edeburn, H. R. Fife

An extended study of dustproofing Freeport-seam coal has emphasized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption propcrties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measurements on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average tori of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by surface area. Wax extraction data on 1-in. to 0 slack from mine-run treated Freeport-searn coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness. The actual cost of the pretipple and supplemental treatments was very low per ton of coal treated, while the net or true cost was sufficiently

Jan 1, 1938

By W. Edeburn, H. R. Fife

An extended study of dustproofing Freeport-seam coal has emphasized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption propcrties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measurements on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average tori of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by surface area. Wax extraction data on 1-in. to 0 slack from mine-run treated Freeport-searn coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness. The actual cost of the pretipple and supplemental treatments was very low per ton of coal treated, while the net or true cost was sufficiently

Jan 1, 1938

By P. Duwez, L. Zwell

In recent years, the problem of pressing metal powder in a die has received much attention. The question has been the object of a Symposium held in New York in March 1947 under the sponsorship of the AIME; an excellent review of the subject may be found in Ref. 1. Various experimental techniques have been used to study the behavior of the powder in a die cavity. Two methods have been particularly successful; one consists of measuring the density distribution²,³ and the other makes use of a lead grid in the powder during pressing.4 In the present study, the pressure at various points on the bottom and the sides of a die 1.50 in. in diam was measured by means of small piston dynamometers and resistance sensitive strain gauges. In order to correlate the results with previous investigations, the pressure distribution inside the compact has also been determined by an indirect method based on density measurements. Strain Gauge Measurements of Pressure on Side and Bottom of Die A schematic drawing of the die used for measuring side pressures is shown in Fig 1. The pressure gauge consists of a 0.25-in. diam piston A which transmits the pressure to a dynamometer B, on which two Baldwin Southwark type 4-14 strain gauges are fastened 180" apart. Because the installation of several dynamometer assemblies along the side of the die would have been difficult, the pressure distribution was obtained in successive tests in which the distance from the gauge to the bottom of the compact was adjusted to different values by changing the length of the bottom piston. The dynamometer, disassembled from the die, was calibrated under compressive loads and showed a 1.00 ohm change of resistance for every 15,300 psi change of pressure (750 lb load change). All the strain gauge measurements were made with a null type Leeds and Northrup Wheatstone bridge. The sensitivity of the method was better than 1 pct and the accuracy was within 2 pct. These values were considered satisfactory in view of the rather large scatter in the measurements introduced by the random variation in packing the powder in the die. The stable ambient conditions and short time involved in the taking of observations made temperature compensation unnecessary-. The pressure distribution on the bot-

Jan 1, 1950