Search Documents

By A. W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall, for oreshoots mined were more continuous than drilling indicated. The Geophysics Dept of Michigan Technological University developed a portable induced polarization drill hole probe with a 3-electrode configuration and a sampling radius of 5 ft ±. A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec intervals and readings are taken every 2 ft. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the 1P potential is sampled for 10 ms and recorded. Resistivity (ohm-ft) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous S values noted. The low resistivity amygdaloid contains sills of high resistivity basalt. Verified by core logs, contacts between amygdaloid and basalt could be picked to ± 0.5 ft from resistivity alone. Lithologic logs of long-steel holes, based on resistivity, then replaced sludge logging. An S value of 30 mv/v was established as the lower limit of diagnostic 1P effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found. During the past ten years, the Calumet Div. of Calumet &Hecla, Inc has conducted extensive exploration and mining in the footwall of the Osceola amygdaloid lode in the native copper district in Michigan's Upper Peninsula. In an attempt to delineate more clearly the extent and nature of high-grade footwall copper mineralization, 876 diamond drill and long steel holes aggregating slightly more than 47,000 ft have thus far been drilled from the accessible hanging-wall workings in the Osceola No. 6, 13, 14 and 15 shafts. Early in this program it became obvious, through inspection of footwall workings in progress, that due to the erratic and bunchy occurrence of the native copper in the footwall zone, the exploration drilling was failing to outline completely the extent of the oreshoots. Early drilling re-

Jan 1, 1964

By Wilhelm Flesch

THE object of development work in the field of gasification is to find a process by which all' fuels, regardless of their individual properties, can be gasified economically. This paper describes the development of the Winkler process. The economy of the gasification process depends not only on the degree of the gasification effect but also, to a decisive extent, on the costs of fuel, production, and installations. Fig 1 shows the relation between fuel costs and gasification efficiency for various types of fuels. Since the fuel cost in the gasification of coke amounts to two thirds of the price of gas, and the thermal unit in brown coal costs only one third of what it costs in coke, it is easily seen how profitably cheap fuels can be gasified, especially if these fuels require minimum preparation and gasification is done in the vicinity of the mines. These possibilities were a great advantage of the Winkler generators, which were installed 20 years ago in the central German brown-coal fields and, at that time, were without rival for the gasification of finely divided fuels. In the Winkler generator (Fig 2), crushed and ground solid fuels were, for the first time, successfully gasified with oxygen and steam on an industrial scale. Unlike the usual processes formerly employed on an industrial scale, this gasification, which proceeds continuously in the glowing, seething fuel bed, makes only extremely low demands on the fuel. The fuel no longer has to be in lumps and abrasion-resistant, but must be capable of reaction and must be fed into the generator in a grain size of 0 to 8 mm. Brown coal or bituminous coal, or their low-temperature cokes, can be gasified in the Winkler generator. Large plants using fuels are operating on an industrial scale in Europe and in Japan. Table 1 shows the results obtained by gasifying these, fuels in Winkler generators. The thermal efficiency of gasification, which is the relation between the calorific value obtained in the gas produced and that of the fuel consumed, gives no indication of the quantity of steam generated in gasification. The generation of steam in the waste-heat boiler of the Winkler generator adequately-covers the steam consumed in gasification. To obtain effective gasification in the Winkler process, combustible mate-

Jan 1, 1953

By Harold C. Price

Prior to Sept. 1, 1928, there had never been constructed what might be termed a long pipe line with electric-welded field joints. A year later more than 2500 miles of electric-welded lines had been completed which varied in diameter from 6 to 20 in., and in length from 50 to 700 miles. This paper discusses methods used on five lines with a total length of about 750 miles. The welding equipment used for the firing line or rolling welds, was 300-amp. generators driven with six-cylinder gasoline engines, and for the bell-hole or tie-in welds, 200-amp. generators driven by four-cylinder gasoline engines. A welding gang consisted of a foreman, 6 to 12 firing-line welders and 2 to 4 bell-hole welders, a mechanic and a tractor driver. Coupons about 1/4 in. thick were frequently cut from completed welds, which showed a cross-section of the weld and an indication of its size and penetration. For tests of tensile strength complete welds were cut out. The tensile strength of 52 welds cut from 420 miles of 12-in. line averaged 50,870 Ib. per square inch. The following results give a fair average of the number of welds made per man per day: on 157 miles of 8-in. line both firing-line and hell-hole welds averaged 15.3—the firing-line average was 21; on 39 miles of 10-in. line the firing-line average was 19.9; on 50 miles of 6-in. line, with unfavorable weather, the average was 17.7; on 424 miles of 12-in. line most of which was welded during the spring, 10.3, and with good weather the average rose to 13 welds per day. The average time for making a complete weld on 12-in. pipe 0.313 in. thick was found to be 30 min. for the rolling weld and 45 min. for tie-in welds. A comparison of costs between electric and gas welding shows that the cost of labor for electric welding is 25 per cent. more than gas, generating cost 61 per cent. less than gas, welding wire 40 per cent. less than gas, and supervision and overhead the same. Estimating 50 per cent, annual depreciation on electric welding equipment, and no depreciation

Jan 1, 1930

By W. I. Duvall, D. E. Stephenson. Discussion by R. G. K. Morrison

R.G.K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que. Canada) - The authors have introduced a subject, the intensive study of which has awaited scientific developments. These are now such as to justify a thorough review of our thinking on the causes and control of rockbursts. The formulae developed in the paper, the comparison between rockbursts and earthquakes in figure 1 and the energy data relating to explosives serve as an effective foundation. In the paper this writer is quoted as suggesting that energy of the order of 10 x 10 11 ft. lb. may have been released in some of the heaviest rockbursts in the Kolar Gold Field. He now hastens to add that such an estimate has no scientific validity. It arises only from a casual comparison of surface and underground effects of the medium heavy bursts, referred to in the paper and estimated by Jones at 3.0 x 1010 ft.lbs., with those of obviously greater magnitude. In any case, we have the estimate by Jones above, that by a team of seismologists 1 on the Witwatersrand of 10 x 1010 ft.lbs., that by Coates of 3.8 x 10" ft.lbs., also referred to in the paper, that by Blan-chard2 for the catastrophic rockburst at Springhill, N.S., of only 7.4 X 107 ft. lbs., and finally the range covered by Cook, referred to in the paper. It is probable also that data for the heavy rockburst at Merkers3 in the WERRA potash area of Germany are available as it was recorded on seismographs from Moscow to Spain. It is the writer's impression that some standardization is present in the estimates above for 10 x 10 10, 3.8 x 1010 and 7.4 x 107 ft.lbs., respectively. The latter, for Springhill, represents a relatively low order of magnitude. It is obvious that any energy estimate must be related to the local geometry of openings at the time of the event. It is also obvious that any explanation of the causes of rockburst must be capable of providing a wide range of energy. However, we must remember that the energy release is an effect indicating magnitude. The cause lies with the mechanism initiating the primary failure, generating the seismic activity, to which much of the damage is probably due.

Jan 1, 1967

THE Institute of Metals Division opened its series of meetings by a session* on lead, R. S. Dean be-ing in the chair and G. 0. Hiers acting as vice-chairman. A large and representative audience listened to the papers in the abstract and contributed an inter-esting and fruitful discussion. The main points of these papers and discussion are given below: In the absence of Carl E. Swartz, the summary and conclusions of his paper, "A Study of the Lead-Tin-Cadmium System with Reference to Their Use as Solders," were read. Swartz investigated a number of alloys in the lead-tin-cadmium system and prepared a diagram representing the solidification ranges of these alloys. He also made tensile strength tests of joints made with these alloys, and compared these with joints made with ordinary lead-tin solder. The tests showed solders containing cadmium were equally strong as the lead-tin series and that the cadmium alloys were suit-able in other respects for use as solders. In general, solders of the composition near to the ternary lead-tin-cadmium eutectic appeared to be the best for most soldering work although compositions widely differing are desirable for special purposes. The lead-tin-cad-mium solders are finding a market particularly in the fields requiring lower solidification temperatures than common solders. Mr. Darby opened the discussion and asked whether it was a fact that the lead-tin-cadmium solders were more useful than ordinary solders on galvanized and tin-plated sheet. C. Smith said he thought it to be a fact that galvanized sheet was more easily soldered by the lead-tin-cadmium solders than common lead-tin-solder. Continuing, Mr. Smith showed lantern slides of his own investigation of the thermal diagram and recommended the 70 per cent lead, 20 per cent cadmium, and 10 per cent tin for general employment. He thought the author did not differentiate between wetting and alloying and pointed out that wetting was more a ques-tion of the flux than the metal. In some cases a definite alloy was formed by soldering and in some no evidences of alloying were found. Illustrating the former case he showed slides and demonstrated that failures always took place longitudinal with the brittle compound alloy and transversely across the solder itself.

Jan 3, 1928

By Nicholas J. Grant, Klaus M. Zwilsky

EVER since the unusual high temperature creep resistance and structure stability of SAP (Sintered Aluminum Powder) and similar aluminum-alumina alloys were reported,'," there has been a need to determine whether other metal-metal oxide (or other hard stable particle) alloys, not so ideal as the Al-Al 2 O 3 system, would show similar high temperature strength and stability. Of the many possible methods of obtaining a metal-metal oxide alloy,a one that offers many practical and theoretical advantages is the simple mechanical blending of metal powders with hard stable particles, followed by pressing, sintering, and hot extruding. With this purpose in mind copper powder and silica and alumina were selected for experimentation because these materials are readily available, cheap, reliable, and lend themseives te the simplest processing and testing. Starting Materials—Two sizes of electrolytically deposited copper powders were used, a —200 mesh powder referred to as A powder in this investigation and a —325 mesh powder referred to as C powder. Silica was added in the form of pure Potter's flint from which a —10µ fraction had been separated. Alumina of the a variety was used in two size ranges. The first was a —10µ fraction separated from a coarser aggregate, the second a commercial product of 0.3µ average diam manufactured by Linde Air Products. Preparation of Powders—Five-hundred gram batches of A copper with 1, 3, and 10 volume pct of each of the three oxides mentioned above were prepared, as well as C copper containing 1, 3, and 10 volume pct of —lop silica. Powders were weighed out carefully and blended by ball milling in air for 24 hr. Since this treatment resulted in surface oxidation of the copper, the charge was hydrogen reduced at 260°C for 5 hr. The next step consisted of hydrostatically compacting the powder into a shape suitable for the required hot working. For this purpose a slug about 11/2 in. in diam and 31/2 in. in length was produced by placing the mixed powders into a rubber sleeve, holding in a perforated steel canister, and rubber stoppering at the ends; the assembly was then subjected to a hydrostatic pressure of 50,000 psi. The air was evacuated from the assembly prior to pressing in order to prevent

Jan 1, 1958

By Robert H. Richards

If one holds up a prism, or wedge of glass, with narrow angle, say l° to 2O, and compares the transmitted image with the image seen above or below the prism, the former will be found to be thrown to one side by an amount varying with the angle of the wedge. Speaking of the two rays as the direct ray and the bent ray, we may say, that when the bisecting plane of the prism is at right angles to the line of sight, the angle between the direct ray and the bent ray will be constant for any given prism. If now we place a prism or wedge of glass in such a position that it half-covers the objective of a telescope, we shall obtain on looking through it two images of every object seen—one image by the direct ray, which comes through the unaovered half of the objective, the other which comes through the prism, and is the image by the bent ray. The angle of divergence of these two raps will be constant and unalterable, whether the telescope is directed to a near object, with its eye-piece at increased distance from its objective, or upon a ' distant object, with eye-piece nearer to the objective. That is to say, if the " throw " or apparent dislocation of the image is one foot in one hundred feet it will be two feet in two hundred, ten feet in a thousand, and so on. The usual form of stadia-telescope has at the focal point of the objective two spider-lines, placed at a definite distance apart and intended, let us say, to represent a throw of one foot in one hundred feet. But as the distance between lines remains the same, while the distance from the objective to the webs diflers with every variation in the distance of observed objects, it follows that the angle between the lines of sight which these two spider-lines define cannot be con stant, but must vary with every increase or decrease of distance be tween the instrument and the object viewed. If in Fig. 1 we represent three positions of the spider-lines by W1, W2, W3, and three objects corresponding to those positions by 01, O2, 0, at near, medium and distant positions, we see at

Jan 1, 1892

By B. D. Cullity

Gold and beryllium form an intermediate phase composed of the two metals in equal atomic proportions and having the formula AuBe. According to Winkler,' this phase probably exists in two modifications: beta, stable below about 600°C, and alpha, stable between 600°C and the melting point, about 740°C. Only the low-temperature beta form will be considered in this paper. Experimental Procedure The gold used had a fineness of 999.75 to 999.85, balance mainly silver, and the beryllium purity was better than 99.8 pct. AuBe was prepared by melting the constituents in a beryllia crucible in an evacuated induction furnace. After melting and thorough mixing, the alloy was allowed to solidify in the crucible. No difficulty was encountered in obtaining a homogeneous ingot. Both chemical analysis and microscopic examination of the ingot showed that the alloy was essentially one phase, containing 50 at. pct gold. The alloy was quite brittle and powder samples could easily be prepared by grinding in an agate mortar. The X-ray diffraction patterns were made with CuK-alpha radiation in a Debye-Scherrer powder camera 57.3 mm in diameter. The film was placed unsym-metrically in the camera in order to afford a basis for film-shrinkage corrections. A sample homogenized at 500°C gave the same diffraction pattern as a sample taken from the as-melted ingot. General Results The diffraction pattern of AuBe was readily indexed on the basis of a simple cubic lattice with ao = 4.659 + 0.001kX. If the unit cell is assumed to contain four AuBe "molecules," the calculated X-ray density is 13.46 grams per cc as compared with the measured density of 13.55 gm per cc. The only missing reflections in the diffraction pattern are (100) and (220) (see Table I). Since these missing reflections are not those characteristic of body or face centering, the lattice of AuBe must be simple cubic. To locate the positions of the atoms within the unit cell, two possibilities had to be considered: I. The structure was disordered and there were eight positions to be filled by an LCaverage" gold-beryllium atom. That the structure was disordered seemed unlikely since the lattice parameter did not vary with composition in alloys containing sornewhat more and somewhat less than so at' pet gold, indicating a fixed composition for AuBe.

Jan 1, 1947

By B. D. Cullity

Gold and beryllium form an intermediate phase composed of the two metals in equal atomic proportions and having the formula AuBe. According to Winkler,' this phase probably exists in two modifications: beta, stable below about 600°C, and alpha, stable between 600°C and the melting point, about 740°C. Only the low-temperature beta form will be considered in this paper. Experimental Procedure The gold used had a fineness of 999.75 to 999.85, balance mainly silver, and the beryllium purity was better than 99.8 pct. AuBe was prepared by melting the constituents in a beryllia crucible in an evacuated induction furnace. After melting and thorough mixing, the alloy was allowed to solidify in the crucible. No difficulty was encountered in obtaining a homogeneous ingot. Both chemical analysis and microscopic examination of the ingot showed that the alloy was essentially one phase, containing 50 at. pct gold. The alloy was quite brittle and powder samples could easily be prepared by grinding in an agate mortar. The X-ray diffraction patterns were made with CuK-alpha radiation in a Debye-Scherrer powder camera 57.3 mm in diameter. The film was placed unsym-metrically in the camera in order to afford a basis for film-shrinkage corrections. A sample homogenized at 500°C gave the same diffraction pattern as a sample taken from the as-melted ingot. General Results The diffraction pattern of AuBe was readily indexed on the basis of a simple cubic lattice with ao = 4.659 + 0.001kX. If the unit cell is assumed to contain four AuBe "molecules," the calculated X-ray density is 13.46 grams per cc as compared with the measured density of 13.55 gm per cc. The only missing reflections in the diffraction pattern are (100) and (220) (see Table I). Since these missing reflections are not those characteristic of body or face centering, the lattice of AuBe must be simple cubic. To locate the positions of the atoms within the unit cell, two possibilities had to be considered: I. The structure was disordered and there were eight positions to be filled by an LCaverage" gold-beryllium atom. That the structure was disordered seemed unlikely since the lattice parameter did not vary with composition in alloys containing sornewhat more and somewhat less than so at' pet gold, indicating a fixed composition for AuBe.

Jan 1, 1947

By Willis Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep ill Johan-nesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104° at sea level, insured reasonable safety, since all parts of the machine operated At subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By J. T. Berling, J. B. Conway

MANY studies have been devoted to the correlation of low-cycle fatigue behavior. Several of these have also been concerned with the identification of an effective approach to the prediction of low-cycle fatigue behavior from short-term tensile data. Perhaps the first such approach was that reported by coffin1 in the form: where is the plastic strain range, Nf is the number of cycles to failure, and c is a constant characteristic of a material. In this analysis by Coffin it was reasoned that in a short-term tensile test the value of Nf could be considered as equal to a , in which case the value of c is interpreted as the tensile ductility, f, measured in such a test. If, therefore, the Coffin equation is assumed to be applicable to a given material, it is a simple matter to predict the low-cycle fatigue behavior. Once the tensile ductility is known, this point is located at Nf = 1/4 on a log-log plot of vs Nf and a line is drawn through this point with a slope of to yield a prediction for the fatigue life. Actually, while this equation is quite useful it is not generally applicable, for experiment has shown that the value of —$ does not reflect the relationship between and Nf for all materials or even for a given material over all temperature ranges. An equation similar to the Coffin equation was prepared almost simultaneously by Manson.2 This expression had the form: In this case the exponent on Nf was not assigned any particular numerical value in accord with the various values of this exponent which had been observed for different materials and at different test conditions. Because of this characteristic it will be recognized that little use can be made of this expression in predicting low-cycle fatigue results. A fairly effective expression for use in predicting fatigue behavior was proposed by Manson3 based on a study of numerous sets of experimental results. This relation (Method of Universal Slopes) makes use of modulus of elasticity, ultimate strength, and tensile ductility, and assumes an exponent on Nf equal to 0.6 in representing the plastic strain range contribution to total strain range. While this equation of Man-Son does not yield completely accurate results it must be recognized as being the best means available at

Jan 1, 1970

By J. Kittl, D. Arias

THE decomposition on cooling of the high-temperature ß bcc phases in copper- or silver-based binary systems usually takes place by a martensitic. massive, bainitic, or pearlitic reaction depending upon the particular conditions of each system. The AgAl system is one of these systems in which a massive or a martensitic transformation can occur upon cooling from the 3 phase field. Recently Hawbolt and Brown1 observed both massive and martensitic transformation products in a 22.7 at. pct A1 alloy. In the present work the massive and the martensitic transformations were investigated in a number of alloys for the composition range between 23.2 and 27.9 at. pct Al. The alloys were prepared using high-purity silver, 99.999 pct, supplied by ASARCO and aluminum, 99.999 pct, supplied by ALCOA. The metals were melted using a graphite or a sintered alumina crucible which was sealed in quartz tubes under an argon atmosphere. The alloys Were remelted to reduce segregation and homogenized in the 13 phase field for 24 hr. The weight of the alloys after homo-genization compared with the initial weight indicating the alloy composition to be within k0.1 pct of the in- tended composition. Chemical analysis of several samples confirmed the estimated alloy composition. All metallographic observations were performed on samples electropolished with ac current using a 10 pct solution of KCN and a stainless-steel electrode. The samples were cut into -1-mm-thick slices, polished, heat-treated in the ß phase field, and quenched in air, ice water, or iced brine. Some heat treatments consisted of a 2-min anneal carried out in air to allow maximum quenching speeds. Other samples were heat-treated in a vacuum of 10"4 torr and quenched using a helium blast in a quenching apparatus described elsewhere.&apos; In both cases, no appreciable losses of silver or aluminum were noted at the sample surface by sectioning and electropolishing. Table I summarizes the microstructure resulting from the various quenching treatments. The composition of the alloys investigated is also indicated on the equilibrium diagram in Fig. 1. The <, hcp phase, typical of a massive ß — cm, transformation, was observed in all alloys. A minimum temperature of 450°C was estimated for this transformation based on preliminary cooling experiments. the results being included in Fig. 1. In these

Jan 1, 1970

By W. L. Zeigler

THE tailing from the gravity concentration plant of the Hecla Mining Co., Gem, Idaho, was former-ly loaded into railroad cars to be used for ballast, highway surfacing material, or concrete work, or dis-posed of by an aerial tramway, which dumped it into another gulch. The tailing averages about 1.2 per cent lead and 0.8 oz. silver to the ton. Further treatment for the recovery of the valuable metals had been investigat-ed several times with results that did not warrant the construction of a retreatment plant; but early in 1925 experimental work was again started with small tests, and later with a 10 tons per day flotation test plant. This showed that the tailing could be ground and treat-ed by flotation at a profit. It was decided to make the new flotation plant an addition to, rather than incor-porate it in the old concentrator, the original capacity of which had been increased many times, the present arrangement being by no means ideal. The old mill buildings were of timber and board contruction, creat-ing more or less fire hazard, so all new construction was made fireproof. Construction work on the new plant was started in the middle of July, 1925, and the plant was placed in operation early in December. The building is of concrete and steel with hollow tile walls, steel sash and corrugated asbestos roofing. The ball-mill floor has for its foundation a cellular reinforced concrete block about 14 ft. deep, extending to cemented river gravel, and the cells filled with tailing to give weight to the block. Overhead, built into the steel frame, is a 5-ton hand-operated traveling crane. With both ball-mills running fully loaded, there is not the slightest trace of vibra-tion in the foundation or building. The flotation floor is of reinforced concrete beam construction and spans Canyon Creek. Adjustable plunger feeders are arranged under the the tailing-bin, which feed by gravity to a 14-in. eleva-tor, discharging to a short 18-in. conveyor. From the conveyor the tailing is discharged into a dividing hop-per, from which point the plant is arranged in three separate units. Each unit consists of a ball-mill in closed circuit with a classifier, and an 8-cell flotation machine and has an approximate capacity of 300 tons per 24 hours.

Jan 8, 1927

All the Technical PUBlications and Preprints published in 1932 are available at Institute headquarters. They are also on file in public, university and technical libraries and, when so indicated in the list, may be found in the Transactions. Copies of the Technical Publications have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Insti-tute of Metals Division; F-Coal Division; G-Petroleum Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of Preprints may also be obtained from the Secretary&apos;s office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. Metal Mining Technical Publi- Title Author Meeting Trans. cation Volume No. and Page* 484-A.45 Propeller Type Mine Fan at Moose A. S. Richardson New York 102, 88. 95 F.52 Shaft. Butte. Montana (13) Feb.. 1932 487-A.46 Progress in the Improvement of Max H. Barber New York. Methods and Equipment at Feb., 1932 Open-pit Iron Mines on the Lake Superior Iron Ranges (9) Pre. Sand Filling through Pipes and Lucien Eaton New York, 102, 33, 41 Boreholes (9) Feb., 1932 Milling And Concentration 445-B.37 Soap Flotation of the Nomulfides Will H. Coghill New York. H.19 (18) J. Bruce Clemmer Feb., 1932 461-B.38 Principles of Flotation—An Experi- I. W. Wark New York. mental Study of the Effect of A. B. Cox Feb.. 1932 Xanthates on Contact Angles at Mineral Surfaces (48) Iron and Steel Division 447-C.81 Electrochemical Potentials of Nitri- Shun-ichi Satoh New York, fied Steels (31) Feb.. 1932 450-C.82 Reaistanoe of Iron-aluminum Alloya N. 9. Ziegler New York. 100, 267. 670 E.143 to Oxidation at High Tempera- Feb., 1932 tures (8) 451-C.83 Pressure Welding of Low-carbon C. H. Austin New York. Steela with Theoretical Con- W. S. Jeffries Feb.. 1932 siderations on the Mechanism of Such Welding (42) 453-C.84 Inclusions—Tbeir Effect, Solubility C.E.Sims New York, 100, 154, 176 and Control in Cast Steel (24) 0. A. Lillieqvist Feb., 1932

Jan 1, 1932

By Martin Epner, Eric Gregory

DURING the past decade, considerable work has been carried out on various cermet systems in an effort to produce materials suitable for high-temperature applications in gas turbines. Most of the materials have not, as yet, met the requirements of the engine manufacturers, primarily because of their lack of room-temperature ductility and thermal shock resistance. In the field of tool materials, however, although ductility is still of prime importance, much has been accomplished by improving design parameters and the quality of carbide materials with a view to using cermet compositions successfully. The systems described in this paper were designed primarily for application in this field, although their development was a natural outcome of work on similar compositions designed for high-temperature service. In steel-bonded titanium carbide, the steel binder imparts heat treatability to the system while the carbide provides abrasion and wear resistance. Combining the carbide and the steel matrix in carefully controlled proportions results in a composite material which, when the steel is hardened, has man of the properties of cemented tungsten carbide. In the annealed condition, this material can be readily machined by the conventional chip-removal techniques. Titanium carbide has certain distinct advantages over many of the other carbides when combined with a steel matrix. It is among the hardest of the carbides and is one of the most stable. Liquid iron wets titanium carbide, and this wetting assists in the formation of a dense cermet. Once the composite structure has been formed, the titanium carbide acts as a relatively inert phase during the heat treatment of the matrix. PREPARATION OF ALLOYS The steel-bonded titanium-carbide materials described in this paper were prepared by the liquid-phase sintering technique. The titanium carbide used had an average particle size of 6 to 7 p, a total carbon content of 19.4 pct and 0.35 pct free carbon. This was blended with the elemental metal powders by ball milling them together in a hexane medium. After drying, paraffin wax was added to the blend to provide green strength in the pressed briquettes, and compacting was performed at 15 tsi. Liquid-phase sintering was carried out in vacuum at temperatures which depended on the chemical composition of the system involved, but which were usually around 2640° F. The resultant materials had a density approaching 100 pct of theoretical. The

Jan 1, 1961

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.&apos;&apos; Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.&apos;&apos; Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942

By J. Versluys

When a well strikes an oil-bearing layer, the oil has a pressure which is generally sufficient to enable it to rise to near the surface (sometimes above the surface). As soon as a well begins to produce, however, the liquid moves through the pores of the reservoir bed and the pressure in the well becomes much lower than the pressure originally prevailing there. At some distance from the well, however, the pressure in the reservoir bed remains unaltered; thus the pressure of the oil has not only to lift the oil, but also to overcome the friction resistance in the pores. The fact that so many oil wells are gushers is a consequence of the energy accumulated in the gas. In gushing the well acts as a gas-lift. A mixture of liquid and gas (the latter partly dissolved in the former) rises vertically from the oil-bearing layer through a cylindrical casing to the surface. In time conditions alter and the well ceases to gush regularly, then the gushing can be further promoted by inserting a narrower tube in the well and connecting the top of the oil string to the tubing. If the action in time becomes irregular, the gushing can be kept up for a further period by forcing gas between the two tubes. In the oil fields the term "gas-lift" is used actually only where extraneous gas is applied, as in the last of the stages mentioned. The action, however, is just the same whether the gas exclusively originates from the formation, or is partly applied artificially. Thus by gas-lift we simply mean a vertical tube in which the energy of gas under pressure, and of dissolved gas, is utilized for raising a liquid. In gushing oil wells the pressure is frequently very high and the absorption coefficient 0.4 (expressed in vol. ratio) of the coexisting gas is not particularly high, so that in reality it should be assumed that a considerable portion of the gas, at any rate at the bottom of the gas-lift, is dissolved in the oil. For water-producing wells this is not usually of such importance. Where the volume of the flowing gas is much greater than that of the flowing liquid, the latter can be suspended in the former in the form of

Jan 1, 1930

By C. A. Wert, M. G. Coleman

The Zener relaxation in alloys in the a! solid-solution region of the Cu-Ni-Zn ternary system has bear investigated. Of the binary solid solutions that bound this region, Cu-Zn and Ni-Zn exhibit measurable Zener peaks whereas Cu-Ni does not. At constant atomic percent copper, the Peak height drops uni.forinly from the value in the Cu-ZTL binary to zero in CIA-Ali. The cariation of peak ternperatuve with composition is linear. At constant atomic percent zinc, the peak height in the ternary alloys goes through a large maximum as compared with the binary values. The temperature of these peaks varies smoothly with composition. The half-width of the peaks in the ter nary alloys, however, are much larger than those in the binaries. A large enhancement of the relaxation strength of the Zener relaxation in ternary Au-Ag-Zn alloys as compared to the relaxation strengths in Au-Zn and Ag-Zn binary alloys was observed by Firson and ert.&apos; Since this effect was unexpected, the present study was devised to investigate whether enhancement of the Zener relaxation in ternary alloys is a general feature or is particular to the Au-Ag-Zn system. We have chosen the Cu-Ni-Zn alloy system for this investigation. Measurable Zener relaxations are observed in both the Cu-Zn and the Ni-Zn binary systems, but not in the Cu-Ni binary system. A large solid-solution region extends to large concentrations of zinc, making it possible to vary composition of the alloys over a wide range without crossing phase boundaries. EXPERIMENTAL PROCEDURE Two series of alloys were prepared. the first at constant atomic percent copper, the second at constant atomic percent zinc. The compositions of these alloys are shown by the circles in Fig. 1. The alloys were prepared by melting the individual components, each of which had previously been vacuum-melted, in an evacuated quartz capsule in an induction furnace at 1500 C. The capsules containing the molten alloys were quenched in water to reduce coring. Any individual melt which exceeded 0.001 pct weight loss was discarded. The ingots were swaged to a 50 pct reduction of area and annealed for 1 week in an evacuated quartz capsule to aid homogenization. The alloys were then

Jan 1, 1967

By Philip W. Moen

It is with sincere regret that the members of the Institute will have heard of the death, on March 17th last, at Terre Haute, Ind., of Professor Charles 0. Thompson, A.M., Ph.D., President of the Rose Polytechnic Institute of that city, and for many years pre viously the head of the Worcester County (Mass.) Free Institute of Industrial Science, and in 1881 and 1882 one of the managers of this society. To us he was chiefly known by the excellent character of the work which he had performed, as a recognized leader among the technical educators of the country. He was a constant, and interested atten dant at our meetings, seeking to acquaint himself not less with all that was noteworthy in the practical attainments and developments of the branches of industry represented by our membership, than with such such facts as would be of service to him in shaping or guiding a wise course of instruction in the institutions of which he had charge. We shall not soon forget him, or the genial courtesy of his manner, or his ready words and thoughtful comments. Charles Oliver Thompson was born September 25th, 1836, at East Windsor Hill, Conn., where his father, Rev. William Thomp son, D.D., was professor in the Connecticut Theological Seminary, since removed to Hartford. The son was fitted for college under the late Paul A. Chadbourne, and entered Dartmouth College in 1854. He was graduated in 1858 with honors. In all the studies of his course he had maintained a high rank, but showed marked proficiency in chemistry and mechanical philosophy. In 1861 he received the degree of A.M., followed by that of Ph.D. from his own college in 1879, and from Williams in 1880. In September, 1858, the year of his graduation, he became principal of the Peacham Academy, Vt., remaining in that position until November of 1864, though during that period he devoted several months to practical work as a surveyor and civil engineer. Thus his experiences were developing the qualities which, later on, fitted him to carry out so successfully the plans of the thoughtful projectors of a new system of technical education, along a path before untrodden, but which the test of time and the indisputable proof of success have shown to be both wise and fruitful.

Jan 1, 1886