Search Documents

By H. E. Lee, A. W. Edelen

The Teziutlan copper-zinc deposit is supposed to be of late Cambrian or early Paleozoic age. The country rocks are a series of schists or phyllites, flat lying and in the form of a plunging anticline. The ore deposit occupies a single horizon in the schist for a known horizontal extent of 1200 meters. Along its strike occur four large lenses or ore bodies. These ore bodies occupy positions along the flank and extend to the crest of the anticline. The primary mineralization is in the form of quartz, pyrite, sphalerite, chalcopyrite and galena, with a few scattered silver anti-monides. Quartz and pyrite form the mineralization between the ore lenses. Ill the ore lenses the sulphides appear as a massive, very fine-grained intergrowth of minerals. The intergrowth suggests a contemporaneous deposition of the heavy sulphides. The grain size, usually under 0.09 mm., makes the separation difficult and fine grinding important. The ore bodies were formed at great depth by solutions probably originating in the same basic magma that gave rise to the dolerite sills that are so common in their vicinity. Introduction The Teziutlan copper-zinc deposit is distinctly different from other ore deposits of Mexico in age and type. Previously stated to be pre-Cambrian in age, it is now quite generally supposed to belong to the late Cambrian or to the early Paleozoic period. Also, in contrast to the usual shallow-vein zone type of mineralization in Mexico, there is here exemplified an intermediate vein zone deposit of copper and zinc. So far as is known, the Tezintlan vein is unique in the history of Mexican geology and in a class by itself, its closest counterpart probably being the copper veins of the pre-Cambrian of Canada. The Teziutlan district is in the extreme northwestern corner of the State of Puebla, Mexico. Teziutlan, the terminus of a branch line of the National Railways from Mexico City, is connected to the mine at Aire Libre by a 17-km. narrow-gauge railroad owned and operated by the Teziutlan Copper Co. Owing to excessive grades on this short linc, Shay-geared locomotives arc used for the transportation of concentrates and supplies.

Jan 1, 1941

By H. E. Lee, A. W. Edelen

The Teziutlan copper-zinc deposit is supposed to be of late Cambrian or early Paleozoic age. The country rocks are a series of schists or phyllites, flat lying and in the form of a plunging anticline. The ore deposit occupies a single horizon in the schist for a known horizontal extent of 1200 meters. Along its strike occur four large lenses or ore bodies. These ore bodies occupy positions along the flank and extend to the crest of the anticline. The primary mineralization is in the form of quartz, pyrite, sphalerite, chalcopyrite and galena, with a few scattered silver anti-monides. Quartz and pyrite form the mineralization between the ore lenses. Ill the ore lenses the sulphides appear as a massive, very fine-grained intergrowth of minerals. The intergrowth suggests a contemporaneous deposition of the heavy sulphides. The grain size, usually under 0.09 mm., makes the separation difficult and fine grinding important. The ore bodies were formed at great depth by solutions probably originating in the same basic magma that gave rise to the dolerite sills that are so common in their vicinity. Introduction The Teziutlan copper-zinc deposit is distinctly different from other ore deposits of Mexico in age and type. Previously stated to be pre-Cambrian in age, it is now quite generally supposed to belong to the late Cambrian or to the early Paleozoic period. Also, in contrast to the usual shallow-vein zone type of mineralization in Mexico, there is here exemplified an intermediate vein zone deposit of copper and zinc. So far as is known, the Tezintlan vein is unique in the history of Mexican geology and in a class by itself, its closest counterpart probably being the copper veins of the pre-Cambrian of Canada. The Teziutlan district is in the extreme northwestern corner of the State of Puebla, Mexico. Teziutlan, the terminus of a branch line of the National Railways from Mexico City, is connected to the mine at Aire Libre by a 17-km. narrow-gauge railroad owned and operated by the Teziutlan Copper Co. Owing to excessive grades on this short linc, Shay-geared locomotives arc used for the transportation of concentrates and supplies.

Jan 1, 1941

By B. D. Cullity

This investigation of bismuth-selenium alloys was made in an attempt to find a suitable material for use in thermoelectric generators. These devices are simply thermocouple circuits designed for the efficient production of electrical energy from thermal energy, which may in turn be derived directly from solar radiation or from the combustion of fuels. The requirements of a material for use in a thermoelectric generator are obviously quite different from those of a material used in a temperature-measuring thermocouple. Naturally, for power generating purposes, the thermoelectric power (voltage produced per degree difference in temperature between the junctions) must be as high as possible. Furthermore, in order to obtain reasonably high power outputs, the materials used in the generator must have an electrical conductivity which is as high as possible. Finally, in order to minimize heat lost by conduction to the cold junction, the thermal conductivity must be as low as possible. The relation between these several factors and the efficiency of conversion of thermal into electrical energy—the thermoelectric efficiency—has been discussed by Telkesl in a recent review of the subject. She gives the thermoelectric efficiency as: W o Efficiency = -Wo ______________i____________ TR-TC+ O2TR-Tc) where W, = power output in external load (watts) Wi = rate of heat input to hot junction (watts) TE,T, = temperature of hot and cold junctions (oA) K1,Kz = thermal conductivity of the two thermocouple materials (watts/cm°C) p,,pz = electrical resistivity of the two thermocouple materials (ohm cm) 9 = thermoelectric power (volts0/C) For many materials, some of the desired properties (for example, high electrical and low thermal conductivity) are almost mutually exclusive; the problem thus becomes one of finding a material which has the optimum combination of pfoperties. Bismuth-selenium Alloys work on the equilibrium diagram of the bismuth-selenium alloys has been reviewed by Hanson who gives the diagram reproduced in There are two intermediate phases in this system, BiSe and Bi²Se3. The existence of an alpha and beta modification of BiSe has not been demonstrated satisfactorily and the writer found no evidence of it in the present work. BiSe and Bi2Se3 have, like bismuth, a rhombohedra1 crystal

Jan 1, 1949

By G. Derge, L. D. Kirkbride

In recent years the problem of sulfur elimination in iron and steel-making has been of increasing importance. This interest has been due to the increasing amounts of sulfur coming into the system via raw materials. As a result, many investigations have been directed at obtaining information pertaining to the rate and mechanism of sulfur removal in the blast furnace as well as measuring appropriate thermodynamic quantities. Chang and Goldmanl as well as others2'3 showed that the process of sulfur transfer from molten carbon-saturated iron to blast furnace-type slags could be considered as two opposing first-order chemical reactions. Recently, Ramachandran et al.4 have shown that during desulfurization electrical neutrality is preserved in both phases and iron and silicon are transferred into the slag concurrently with the evolution of carbon monoxide gas. They concluded that the reaction s + c-+ (0)=(S) + CO(g) does not express the stoichiometry of the sulfur transfer process. As in all previous investigations, these authors studied the process of a net transfer of sulfur from metal to slag across a slag-metal interface. However, no experimental data have previously been obtained for the process of sulfurization. It was the purpose of this study to investigate the sulfurization process, i.e., net transfer of sulfur from slag to metal. EXPERIMENTAL PROCEDURE Apparatus—The equipment used in this investiga-tion was typical of that used by others.1-3The furnace was a high-frequency induction unit powered by a 35 kw Hg spark gap converter. Fig. 1 shows a schematic diagram of the apparatus. A two-compartment crucible assembly was employed to melt the slag and metal charges; being similar to that used by Ramachandran,4 in size and design. The atmosphere was that produced by reaction of hot graphite with air. Temperature measurements were made by W-Mo thermocouples which were calibrated against a Bureau of Standards Pt - Pt 10 pct Rh couple. Temperature control was always good to * 5°C and in general was much better than this figure. Raw materials used in the experiments were C. P. reagent grade where possible. The silica used in the preparation of the slags was in the form of highly purified silica flour. Silicon and titanium additions

Jan 1, 1961

By Tracy C. Jarrett

The alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,' E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various elements upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency inductiorl furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5" F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by 45 by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by % by % in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second scries consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1940

By Tracy C. Jarrett

The alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,' E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various elements upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency inductiorl furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5" F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by 45 by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by % by % in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second scries consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1940

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main Tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials, it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted. A tight partition of 2-in. (5.08-cm.) plank was erected between the auxiliary and the adjoining hoisting compartments, for better protection of men riding on the cages. The application of concrete made this

Jan 1, 1920

By W. J. Hillenbrand

The soda-ash method for eliminating arsenic from a molten copper bath has been described previously in some detail.' Briefly, the process consists in blowing powdered sodium carbonate under the surface of the partially oxidized melt and in removing the slag formed, which will contain a certain proportion of the arsenic formerly in the bath. Sodium carbonate melts readily at the temperature of molten copper, and when molten it dissolves arsenic oxide rather rapidly. In the process, sodium arsenate is formed which is removed along with the excess of molten soda ash. In order that arsenic may be eliminated in this way, it must first be oxidized to the pentavalent condition. This, however, is easily accomplished by blowing air into the molten copper until a fair excess of cuprous oxide is present. The manner in which soda ash is introduced into the furnace has a considerable effect upon the efficiency of the process. In the earliest attempts at arsenic removal, soda ash—often in combination with slaked lime, for sodium carbonate is not the only solvent that will remove arsenic—was thrown upon the surface of the bath, was allowed to melt, and was removed after it had dissolved a sufficient amount of arsenic. At present powdered soda ash is generally blown in under the surface of the melt with the aid of compressed air. Melting immediately as it comes into contact with the molten copper, it can react with considerably more of the bath than by the former method, and thus can remove arsenic more rapidly and more completely. Since the resulting slag is removed at once, its very destructive effect upon the furnace refractories is minimized. The effectiveness of the soda-ash method may be gathered from the results of the following test. A 900-lb. charge of copper was melted in a small, oil-fired reverberatory furnace, and sufficient metallic arsenic was added to the bath to bring the concentration of that element to about 0.5 per cent. Air was blown into the melt until its oxygen content was just under 1 per cent by weight. The bath was then sampled and soda ash was blown in under the surface in 5-lb. batches. After each addition

Jan 1, 1934

By D. H. Forbes, H. M. Manasevit, F. L. Morritz

Single-crystal thin films of molybdenum have been grown. by the pyrolytic decomposition of molybdenum hexafluoride in a hydrogen ambient on various insulating substrates at temperatures front 650° to 900° C. Single-crystal discs of various orientations of magnesium aluminate spinel, a aluminum oxide, magnesium oxide, and the natural facets of beryllium oxide were all observed to exert epitaxial control on the depositing film. Determinations of the crystallographic relationships existing between film and substrates have been made, using X-ray diffraction three-circle goniometry and Laue back-reflection techniques. Using these data, crystallographic overlays have been constructed which suggest a possible interfacial geometry on the basis of a match between metal deposit atoms and metal ion sites in the substrate. A continuing program has been in effect in the Auto-netics Laboratories over the past several years aimed at the development of electronic materials in new and useful forms using chemical vapor deposition techniques. During the course of these investigations, the epitaxy of silicon1"5 and tungstenep7 on single-crystal metal oxide insulators was studied extensively. The deposition of molybdenum is a logical extension of the tungsten work since the crystal structure is identical and the lattice dimensions differ by less than 1 pct. The pyrolytic decomposition of molybdenum hexafluoride in hydrogen was used to grow molybdenum films on the oxide substrates AlzOs, MgA1~04, MgO, and Be0 at from 650" to 900°C, depending on the substrate material. Under the experimental conditions to be described, monocrystalline films of controlled orientation were obtained. The materials investigated and their crystal structure are listed in Table I. EXPERIMENTAL The molybdenum depositions were effected by the hydrogen reduction of molybdenum hexafluoride (MoFe) in a flowing system of hydrogen at atmospheric pressure. The schematic of the apparatus is shown in Fig. 1. The hydrogen, purified by passage through a heated palladium thimble, was mixed with the vapor of the liquid MoFe maintained in a steel bottle at room temperature (25°C). The mixture was passed over the substrate, which was heated by rf induction of a sup-

Jan 1, 1969

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By William H. Radford

Having worked some rather lorn--grade gravel during the past season at a small profit, I give the actual figures, in the hope that other mining engineers interested in this line of work may be thereby induced to do the same, in order that we may all get more data on this little-ventilated subject. The property here referred to is situated in one of the northern counties of California, where hydraulic mining is still permitted by the courts. The water-right belonging to the mine is a good one, furnishing water during about nine months, whenever there is an average rain-fall, and a fair proportion of the precipitation is in the form of snow. The ditch, about 11 miles in length, is cared for during the rainy months by two men, and during the rest of the year by one; and the water cost last season, delivered at the mine, 0.69 cent per miners' inch. The season commenced in November, 1899, and ended the last of July, 1900. During this time, 655,657 miners' inches (an inch equals 1728 cu. ft. in 24 hours) of water were used for piping, and for sweeping the bed-rock at the end of the season. From actual surveys, this amount of water washed down 1,251,399 cu. yds. of material, consisting of pay-gravel lying on the bed-rock, and varying in thickness from a few inches to 8 ft., and practically barren top-material, consisting of mountain slide, carrying considerable broken rock, clay, and soil. The banks varied in height from 50 to 130 ft., the average height being 63 ft. The grade of the sluices was 7 in. to 12 ft., the boxes being paved with block-riffles 12 in. deep. Long bed-rock cuts extended from the heads of the sluices to within a few feet of the banks, and were kept practically to grade as the work advanced. At first, electric drills were used on this work; hut as it was found that heavy blasting shattered the rock too much, and caused slips, these drills were

Jan 1, 1902

By George Hallerman, R. J. Gray

In the customary method of studying age hardening, the process of aging is interrupted by cooling the specimen and measuring its room-temperature hardness. However, the aging process may be conveniently measured while it is occurring at an elevated temperature by a series of hardness measurements at suitable time intervals. The latter method gives data void of complications that might result from processes occurring during the quench, and the data may be more indicative of the alloy's properties at elevated temperatures. The elevated-temperature hardness tester1 used in the present study employed a dead-weight loading system with a synthetic sapphire Vickers-type in-denter mounted in a molybdenum holder. The tests were performed in a vacuum of l0 to 10 torr. Hardness impressions were made by applying a 2-kg load for 15 sec. Although the hardness impressions made in the tester at elevated temperatures were measured at room temperature, the correction for thermal contraction during cooling was insignificant and therefore neglected. The two methods of obtaining age-hardening data were compared using eighteen samples of Haynes alloy No. 25* which had been annealed for 2 hr at 2250°F (1232°C). The test surfaces of the 1 by 1 by 1/4-in. samples were ground and then polished on vibratory polishers2 prior to testing. Three groups of five samples were aged at 1400°, 1650°, and 1800°F (760°, 899", and 982°C) for 4, 16, 32, 64, and 100 hr and then water-quenched. Room-temperature hardness as a function of aging time for these samples is shown in the broken lines of Fig. 1. Only one sample for each of the three temperatures was necessary to determine the hardness of the alloy at the aging temperatures with the elevated hardness tester. The specimens were heated isothermally and hardness impressions were made after various time intervals up to 100 hr. The results of these determinations were represented by solid lines in Fig. 1. Comparison of the two sets of curves shows, as expected, the hardness values determined at the aging temperatures are lower than the room-temperature hardness of the quenched specimens and the hot-hardness values reflect a strong tempera-

Jan 1, 1964

By Tracy Jarrett

THE alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,1 E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various ele¬ments upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency induction furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5° F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by ½ by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by ¼ by ¾ in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second series consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1939

By B. L. Dunic, Terkel Rosenqvist

rr has long been suspected that sulphur has a small but finite solid solubility in iron, but up to the present more accurate data have been lacking. The survey given by Hansen' illustrates the divergence of data and opinions. Solubilities between 0.01 and 1.5 pct have been suggested, and opinions vary regarding the effects of temperature and phase transformations in iron on the sulphur solubility. The extent of solid solution and its variation with temperature might be expected to be an important factor in the occurrence of hot shortness in steel. Therefore, the object of the present investigation was to study this problem more systematically. It was furthermore hoped that solubility data for sulphur might contribute to an understanding of the factors which determine solid solubilities in general. Experimental Procedure The present work was based on the measurement of the chemical activity of sulphur in the solid solution by means of equilibrium with a mixture of hydrogen and hydrogen sulphide. When the solid solubility limit is reached, the sulphur activity in the iron becomes equal to that in the coexisting sulphide phase. A gas mixture of a controlled H,S/H, ratio was passed over pure metallic iron heated to a temperature in the range 900" to 1500". The amount of sulphur absorbed by the iron was determined by analysis, and from a plot of percentage of sulphur vs. gas composition the sulphur activity and the solubility limit were determined. As the rate of diffusion of sulphur in solid iron is very small, often several days were needed to be sure that equilibrium conditions had been established. To produce a gas flow with less than 1 pct H,S of constant composition for several days, was in itself a problem. The most satisfactory arrangement was obtained by a continuous synthesis of hydrogen sulphide from the elements. This was done in the part of the apparatus shown to the left in Fig. 1. The hydrogen used was first purified in tank batches by passage through activated charcoal cooled in liquid nitrogen under a pressure of 150

Jan 1, 1953

HeRbert A. MeGRaw, San Luis de la Paz, Guanajuato, Mex. (communication to the Secretary*) :—Although Mr. Bordeaux prefaces his paper with the statement-that it is a general outline of practice in the Republic, many of his statements seem to be made from the view-point of a particular case, which does not always agree with general practice. For the purpose of calling attention to some of these variations, I respectfully offer the following comments: The operation of crushing and grinding is performed by so many different methods and systems that it is useless to select any one as the standard. However, primary crushing in rock-breakers followed by stamps is thus far so general that it might be so classified. Whether or not it is the best way, is open to question. Regrinding may be performed by any of the various types of Chilean mills, Huntington mills, or similar machines, or the material may be taken directly from the stamps and delivered to the tube-mills. Mr. Bordeaux's statement that " the slimes can be treated only by decantation; the new Butters slime-filter, as used in Nevada, does not seem to be successful with silver-ores," is surely an error. All over Mexico many of the purely silver-ores are being successfully handled by the Butters or similar filters, such as the Moore and the Burt filters, and a letter to the manufacturers of these filters will undoubtedly bring a list of the silver-ores now being successfully treated in this way. The statement that crushing silver-ores in solution is impossible is equally erroneous. Most modern mills crush the ore in solution, in some cases containing as much as 0.12 per cent, of KCN. I cannot for the moment recall any modern mill in Mexico which does not follow this practice. There may be some reason for it in particular instances, but, generally speaking, the practice is to crush in solution. Care in installation avoids any mechanical loss of cyanide, and the chemical loss is so small as to be negligible.

Jan 1, 1910

By Walter M. Small

Austria produced approximately 800 cisterns of 10,000 kg. each (56,000 bbls.) of crude oil of a 0.9428 sp. gr. during 1935. Of this Gosting II well near Zistersdorf, owned by the Erdolproduktions-Gesellschaft m.b.H., produced 86 per cent of the total, averaging a little over 1.8 cisterns, or about 125 bbl., per day. Gosting IVa of the same company was put in production early in December and produced a total of about 70 cisterns (4900 bbl.). Gosting IV was a failure, but a directional hole drilled from the same derrick produced Gosting IVa. Gosting I, a well owned jointly by the company above mentioned and the Raky-Danubia, was deepened late in the year and made about 2800 bbl. of oil at the rate of 70 bbl. per day. Completions during the year were as follows: In the Gosting pool, Gosting IV and IVa, drilled with rotary tools, the latter producing from Sarmat at a depth of 934 meters (3065 ft.); Kronberg I, of European Gas & Electric Co. with cable tools in Flysch at a depth of 566 m. as a dry hole; in the Oberlaa gas pool, one cable-tool well of the same company at a depth of 266 m. as a dry hole and one Fauck-Haiek system well of the Vacuum Oil Co. at a depth of 483 m. as a dry hole; one rotary hole of the European Gas & Electric Co. at Enzersdorf a/d. Fischa plugged and abandoned in Sarmat after a blow out and gas eruption at a depth of 699.5 meters. The status of drilling wells at close of the year is as follows: In the Gosting pool, Erdol Bohr- und Verwertungs G.m.b.H., north of the producing area, was drilling with rotary at 990 m., Raky-Danubia is rigged up to deepen the old Windisch-Baumgarten hole, Rohoel-Gewin-nungs A.G. (Vacuum-Shell combination) rigging up rotary south of the production, and Steinberg-Naphta G.m.b.H. (Musil) was deepened with light rotary to 830 m.; at Enzersdorf a/d. Fischa, the European Gas & Electric Co. E-2 rotary-drilled hole stood at 1533 m. in Miocene waiting

Jan 1, 1936

By Walter M. Small

Austria produced approximately 800 cisterns of 10,000 kg. each (56,000 bbls.) of crude oil of a 0.9428 sp. gr. during 1935. Of this Gosting II well near Zistersdorf, owned by the Erdolproduktions-Gesellschaft m.b.H., produced 86 per cent of the total, averaging a little over 1.8 cisterns, or about 125 bbl., per day. Gosting IVa of the same company was put in production early in December and produced a total of about 70 cisterns (4900 bbl.). Gosting IV was a failure, but a directional hole drilled from the same derrick produced Gosting IVa. Gosting I, a well owned jointly by the company above mentioned and the Raky-Danubia, was deepened late in the year and made about 2800 bbl. of oil at the rate of 70 bbl. per day. Completions during the year were as follows: In the Gosting pool, Gosting IV and IVa, drilled with rotary tools, the latter producing from Sarmat at a depth of 934 meters (3065 ft.); Kronberg I, of European Gas & Electric Co. with cable tools in Flysch at a depth of 566 m. as a dry hole; in the Oberlaa gas pool, one cable-tool well of the same company at a depth of 266 m. as a dry hole and one Fauck-Haiek system well of the Vacuum Oil Co. at a depth of 483 m. as a dry hole; one rotary hole of the European Gas & Electric Co. at Enzersdorf a/d. Fischa plugged and abandoned in Sarmat after a blow out and gas eruption at a depth of 699.5 meters. The status of drilling wells at close of the year is as follows: In the Gosting pool, Erdol Bohr- und Verwertungs G.m.b.H., north of the producing area, was drilling with rotary at 990 m., Raky-Danubia is rigged up to deepen the old Windisch-Baumgarten hole, Rohoel-Gewin-nungs A.G. (Vacuum-Shell combination) rigging up rotary south of the production, and Steinberg-Naphta G.m.b.H. (Musil) was deepened with light rotary to 830 m.; at Enzersdorf a/d. Fischa, the European Gas & Electric Co. E-2 rotary-drilled hole stood at 1533 m. in Miocene waiting

Jan 1, 1936

By C. O. Brawner

INTRODUCTION Tailings dams up to about 200 ft. high are proposed to store tailings for a major mining operation on Marinduque Island in the Philippines. The original design of the dam utilized a compacted laterite starter dam followed by hydraulic placement of cycloned sands to form slime retaining dykes along the outer face of the dam. The upstream method of construction was proposed. In view of the failure of numerous tailings dams in Chile during the EL Cobre earthquake (I), an investigation was performed to assess the earthquake stability of the proposed dam. This included a soil investigation on the first cycloned sand dyke, which had been built to a height of 45 ft. Results indicated that the density of the sand was much lower than existing empirical criteria consider to be necessary for resistance to liquefaction. As a result, the dam was redesigned. The downstream method of construction was selected and a yearly construction program was developed to make use of sand available by cycloning. To increase shear strength, improve resistance to liquefaction, and to utilize steeper slopes, compaction of all sand in the dam was specified. A special underdrainage layer and toe drains were incorporated in the design. Details of the decant system and surface erosion alternatives are described. SITE CONDITIONS The mining project is located in the Philippine Islands. At the present annual rate of production, about 4,230,000 cu.m. of tailings will be produced yearly. The volume requirements for tailings storage design for the first 10 years of operation are in the order of 45,000,000 cu.m. The topography near the mine is mountainous with many gullies and canyons carved out by high intensity rainfall and runoff. The bedrock, which is generally shallow and weathered for a considerable depth, is overlain by laterite soils. Vegetation is comprised largely of palms, banana trees, and tropical shrubs and grasses. Precipitation is heavy. The average yearly rainfall over 24 years is 65.2 in. and the maximum recorded 24 hour rainfall is 9.0 in. High intensity rainfall is associated with typhoon storms, which are a seasonal threat inthe Philippines. Fig. 1 shows a summary of monthly precipitation.

Jan 1, 1972

By Frank E. Neil, O&apos

The formation tester, as the name implies, is a tool built for testing the contents of sands encountered in drilling Wells Without actually cementing casing on the sand. The tester was developed in the Mid-Continent and has been in use commercially there since about 1926. However, some two dozen patents have been issued on formation testers dating back to the seventies. The method apparently was an outgrowth of the old Mother Hubbard grain or bean packer, used around casing before the days of cementing casing. These packers were also seated in a tapered hole and if the formation tested was not satisfactory the casing was pulled loose and the hole taken down to another formation. A great deal of experimental work has been done in its development, and as a result of this work the formation tester became an accepted integral part of the petroleum development in California. The formation tester was introduced into California some three years ago by M. 0. Johnston. Months of discouraging and expensive work followed its introduction into this state, but one organization after another tried the tool and its use is now fairly general. Shortly after Johnston began testing in California, the Halliburton tester was also introduced into the state and now another tool is being introduced, the Shaffer-Roles tester. Principle and Operation of Testers The principle employed in all formation testers is that of packing off the fluid in the hole above the formation to be tested and thereby prevent,ing it from having access to the testing tool. This permits the fluid contained in the given formation to have unrestricted access to the tool. It is accomplished by running the tool and packer on the bottom of the drill pipe; the valves in the tool being closed while going into the hole to prevent fluid from entering the drill pipe. The packer is then seated at the desired point, trapping the drilling fluid above it. When this has been done, the valves in the tool are opened and the fluid from the formation is allowed to enter the empty pipe through the tool. If the

Jan 1, 1934