Search Documents

By C. W. Vaupell

THE Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resurgence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barcenite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available. INTRODUCTION The Huitzuco mercury mines are of interest because of the unusual occurrence of ore in extinct geyser vents and the presence of several rare mercury minerals. Some of the deposits have typical characteristics of the telethermal zone and there is a gradation towards typical epithermal mineralization in depth. Halse,1 Villarello,2 Mactear3 and Merrill4 have described the geology and the early operations in the district, and Barcena5 and Mallet6 have described the rare mercury minerals, livingstonite and barcenite, found at Huitzuco. LOCATION The village of Huitzuco lies in the north central part of the State of Guerrero, Mexico, 27 km. (16.7 miles) east of Iguala, which is the largest and most important town in the area. Iguala is served by the Mexican National Railways and also by the Mexico City-Acapulco highway. The highway is surfaced from Mexico City to Iguala, a distance of 200 km. (124 miles) by road, and there is a fairly good, level, dirt road from Iguala to Huitzuco. The elevation above sea level is about 1000 m. (3280 ft.). The climate is warm and very dry except during the rainy season, from June to

Jan 1, 1937

By Berke L. Thompson

INTRODUCTION Purpose of Wall System There were 2379.88 m (meters) of tied back wall along Interstate 77 in the Capitol Complex area in Charleston, West Virginia. The main purposes of this wall system was for aesthetics, reduction of excavation, saving the forested slopes, and control of sloughage of the back slopes onto the Interstate. Failure At 1 PM on Thanksgiving Day, 1982, 3 wall panels fell from the insitu position onto the interstate in a matter of seconds. See Fig. 1. The total length of wall that fell was 29.25m. The height of the three panels varied from 10.06m to 10.36~1 and each individual panel had a length along the highway of 9.75m. These were abutting panels that were approximately in the middle of a section of wall 165.81m long. The panels separated from the remainder of the wall at 2 expansion joints that occur at the ends of every 3rd panel. The reinforced portland cement concrete panels were designed on a 76.2mm (millimeter) batter. See Fig. 2 for Wall Dimensions. The footer for these panels was lm wide, was keyed into sandstone bedrock 0.30m and was approximately 1.52m below the portland cement concrete pavement and shoulder. Thirteen of the 17 panels in this section of wall were tied to the sandstone bedrock behind the wall by either 25.4mm or 34.93mm hollow rock bolts. Two panels on each end of the wall were cantilever type walls. The panels that failed had 25.4m hollow rock bolts. A portion of each panel adjacent to both sides of the failure was pulled out from the rock face and appeared to be in imminent danger of also failing. All of the 21 rock bolts in the panels that fell were separated either at the backface of the wall, in the extension from the wall to the rock face or at the rock face. None of the rock bolts had been pulled out of the bond length in the sandstone bedrock. After considering the condition of the wall and

Jan 1, 1984

By R. L. Rickett, W. C. Leslie, W. D. Lafferty

Notch toughness of 0.10'pct C steels, rimmed or killed, is improved by holding the steel at a temperature just above the Ae,, followed by air cooling. The improvement can be gained without apparent change in gross microstructure or hardness. The limits of the process have been determined and some possible reasons for the observed effects are discussed. The results appear to indicate that the current theories of transition temperature are inadequate. THE effects of gross microstructural variables (ferrite grain size, austenite grain size, type and distribution of carbides) on the notch toughness of mild steels have been the subject of many investigations.'-' The results indicate that increasing ferrite grain size raises the notch-impact transition temperature. The transition temperature also rises with increasing size of pearlite colonies and with increasing prior austenite grain size, but these factors are not independent of ferrite grain size. The effects of gross composition of steels have also received considerable attention. As a result, manganese, nickel, aluminum, and silicon are known to improve the notch toughness of mild steels. The other elements that have been investigated—carbon, nitrogen, boron, copper, chromium, molybdenum, phosphorus, sulfur, titanium, and vanadium—reportedly are either deleterious or have little effect on notch toughness. Despite this large volume of work, it is still not possible to predict the notch toughness of a mild steel from its microstructure and composition, even when these are supplemented by hardness and tensile tests. Steels with equivalent microstructures, but different thermal and/or mechanical histories, can differ in notch toughness. Such factors as type and distribution of precipitates, substructure, local variations in composition, or unrecognized variables, may be important in determining the notch toughness of mild steels. However, quantitative knowledge of the effects produced by these factors is almost completely lacking. In an effort to improve this situation, an investigation was begun to determine the effect of a very fine precipitate on the notch toughness of low-carbon steels. Aluminum nitride was chosen as the precipitate because of its presence in aluminum-killed steels, the ease of control of precipitation, and past

Jan 1, 1961

By John P. Hager, Adolfo R. Zambrano

The thermodynamics properties of the liquid Pb-Ag-Au system have been determined from galvanic cell measurments five pseudobinary systems of fixed XAg/XAu ratio. The galvanic cell employed a molten PbO-SiO2 electrolyte and was operated between 775" and 1030°C. The thermodynamics properties of lead were obtained directly from the experimental data, whereas the excess integral molar properties and the activities of silver and gold were obtained by means of the Gibbs-Duhem equation. The calculated proper -ties of the Ag-Au system agree well with the published properties. The liquidus surface of the Pb-Ag-Au system has been determined at 1200°K. In Parts I' and 11' the galvanic cell Mo,Pb(l)|(PbO-SiO2)(l) SiO2(s) |Pb(alloy)(l), Mo [I] was used to determine the thermodynamics properties of the Pb-Ag and Pb-Au systems, respectively. The use of cell I, in which a molten oxide electrolyte is employed rather than the classical fused-salt electrolyte, was shown to result in more accurate ther-modynamic measurements in that the displacement reaction at the alloy-electrolyte interface (l/Zb)B(alloy) + (I/za)A+Za = (1/Za)A(alloy) + (1/Zb)B+zb [1] was minimized. For the Pb-Ag system, where B = Ag(l), the error in the activity of lead (aPd) re-sulting from Reaction [I] was calculated to be less than 1 pct.l For the Pb-Au system the error in aPb was calculated to be less than 0.5 pct.2 Also, electro-transport measurements on the PbO-SiO2 electro-lyte1,2 established that the conduction was entirely ionic and that lead was present only in the divalent state. In the present study the experimental technique is extended to an investigation of the thermodynamic properties of the liquid Pb-Ag-Au system. Five pseudobinary systems of fixed X Ag/XAu ratio were selected. The experimental results were then combined with the previous measurements on the component binary systems Pb-Ag1 and Pb-AU2 to calculate, by means of the Gibbs-Duhem equation, the molar and partial molar mixing properties for the liquid ternary solutions.

Jan 1, 1970

John Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—After looking over the authors' shoulders for several years and after many discussions on the interesting diagrams of the types shown, it is a pleasure to see a formal paper published on this subject. There can be no doubt of the practical usefulness of the concepts shown. Inclusion formation in steel is such a highly complex matter that any system for understanding the subject is bound to be welcomed by those who must work with steels and who see in their day-to-day experience the good and evil effects of inclusions. A feature of the work with which the discusser has been concerned, and which he would now like to attempt to explain, is the relation between the schematic diagrams which the authors use and the phase diagrams for related systems. Obviously, the authors' diagrams are in no sense complete phase diagrams. However, there is a relation between this type of diagram and the true phase diagram, and the understand- ing of this relation ought to help in understanding the general picture which the authors are presenting. Consider the authors' Fig. 4, which shows the liqui-dus relations in the Fe-Mn-S-0 system. To show the complete relations between temperature and composition in these four ternary systems would require four triangular prisms, the vertical axes of which would represent temperature. The four triangles of Fig. 4 represent basal projections of certain lines from the four prismatic phase diagrams. Readers of the paper are all more or less acquainted with this type of projection and its usefulness and limitations are generally understood. In order to concentrate on the interesting parts and to minimize the less interesting features, the composition scale may be shifted to de-emphasize regions containing gaseous sulphur and oxygen. Such a diagram is shown in Fig. 16, which is a distorted version of the authors' Fig. 4. Here the oxide of iron is wiistite, denoted by W, and it is to be noted that between W and MnO lies the entire MnO-FeO "binary" system. Similarly, between MnS and FeS lies another binary whose

Jan 1, 1956

By Arthur Taggart

A GENERAL awakening of interest among mill men concerning the mechanical efficiencies of their crushing machines is evident from a perusal of the recent files of mining publications. Considering the large part of the power bill which must be debited to the crushing department, such. interest is natural. When, however, the articles on the subject are read, the only statement upon which the writers agree is that fine grinding consumes a large amount of power, and that the machine which, from a concentration standpoint, offends as a slime producer is, for that reason, a serious offender in wasting power. When the mill man attempts to find a method for measuring the power wasted, or to compare the efficiency of one machine with that of another for the same work, he is confronted with a choice of methods which lead to conflicting results. There are two reasons why the work of crushing is not more generally understood. In the first place, experimental data are difficult to obtain; and in the second place, before these data can be put in general form certain assumptions must be made. A difference in these assumptions by different investigators has led to conflicting conclusions. This conflict has resulted in the proposal of two laws. The first of these is the so-called Rittinger's law, which is variously stated as follows: . "The work of crushing is proportional to the reduction in diameter."-R. H. Richards: Ore Dressing, p. 304 (1903). "The Work required to crush rock is very nearly proportional to the reciprocals of .the diameters crushed to."-A. Del Mar: Engineering and Mining Journal, vol. xciv, No. 24, p. 1129 (Dec. 14, 1912). "The Work done in crushing is proportional to the surface exposed by the operation, or better expressed for this purpose, the Work done on a given mass of rock is proportional to the reciprocal of the diameter of the final product, assuming that all the mass has been reduced to one exact size, which is only theoretically possible."- A. 0. Gates: Engineering and Mining Journal, vol. xcv, No. 21, p. 1039 (May 24, 1913).

Jan 1, 1914

By Henry B. Smith, S. Paul Lindau

ThREe years ago it was decided by the management to granulate the matte that is produced in the smelter of the St. Joseph Lead Co. at Hereulaneum, Mo., thereby doing away with a large amount of labor in handling the matte and in subsequent crushing. On Mar. 1, 1915, the granulator was put in operation and up to Jan. 1, 1916, 18,735 tons had been granulated. The four blast furnaces have a daily output of about 280 tons of pig lead and 100 tons of matte assaying about 11.0 per cent. Pb. It is expected that projected improvements in roasting methods will eliminate more sulphur from the charge, and cut down the matte-fall to about one-half of the present figure. The blast furnaces are tapped into movable forehearths or settlers, 6 ft. by 4 ft. by 22 in., the slag overflowing into 27-cu. ft. slag cars which are hauled to the dump by electric locomotives. Previous to the adoption of granulation, the matte was tapped from the forehearths into small slag pots which were dumped after cooling. The matte cakes were broken with sledges, and transported to the crushing plant for fine crushing and screening. Here the matte was reduced to 1/4-in. size before being fed to the roaster bins. A Wedge and a Holthoff mechanical furnace are used for preroasting before sintering on the Dwight and Lloyd machines. The matte is returned to the furnaces as an iron flux until the gradually accumulating copper content reaches about 7 per cent., after which it is put aside to be concentrated in a small copper blast furnace, the resultant high-grade matte being sold. When the matte does not settle readily from the slag, two settling devices are often used, the second one being a large catch-pot, which gathers any matte that may overflow from the forehearth, the slag then overflowing from the catch-pot into the slag cars. When full of matte, the catch-pot is removed, allowed to cool, and the contents broken and crushed. a With the present plan of granulating, the matte is tapped into 6-cu. ft. iron ladles. These are transported to the granulating plant by a 5-ton

Jan 1, 1917

By S. C. Das. Gupta, B. S. Lement

isothermal formation of martensite occurs in the range of —65o to —197oC and is always preceded by some athermal transformation. By rapid cooling the isothermal, but not the athermal, component of transformation can be suppressed. Stabilization against isothermal transformation can be induced by cycling from below M. to room temperature. A LTHOUGH the transformation of austenite to XV martensite is generally believed to occur only on cooling, recent evidence indicates that this reaction can also occur at constant temperature. Isothermal formation of martensite was observed in tool steel by Fletcher, Averbach, and Cohen.'. They found that the hardening reaction that occurs during the quenching of a plain carbon or low carbon alloy tool steel does not stop immediately when room temperature is reached; instead austenite continues S. C. DAS GUPTA is Research Fellow, Department of Metallurgy, University of Notre Dame, Notre Dame, Ind. B. S. LEMENT, Associate Member AIME, is on the Research Staff, Department of Metallurgy, Massachusetts Institute of Technology, Cambridge, Mass. Discussion on this paper, TP 3123E, may be sent, 2 copies, to AIME by Dec. 1, 1951. Manuscript, April 16, 1951. Detroit Meeting, October 1951. This paper represents part of a thesis by S. C. Das Gupta submitted in partial fulfillment of requirements for the degree of Doctor of Philosophy in Metallurgy to the University of Notre Dame. to transform at room temperature although at a decreasing rate. Since only a small amount of austenite transforms in this fashion, isothermal formation of martensite was considered to be merely a "tailing off" effect of the main hardening reaction. Another point of view was advanced by Kurd-jumov and Maksimova"' * who reported that the austenite-martensite reaction could be suppressed by rapid cooling of a 6 pct Mn-0.6 pct C steel in liquid nitrogen and that as much as 25 pct martensite could be formed by reheating to and holding at subzero temperatures above that of liquid nitrogen. These investigators came to the conclusion that martensite is thermally nucleated at certain special regions in the austenite and subsequently grows to observable dimensions. Isothermal transformation of austenite to martensite was cited by Fisher, Hollomon, and Turnbull" as evidence supporting another nucleation and growth theory of martensite formation. According

Jan 1, 1952

By A. S. Eve

IN the spring of 1930, the question was raised as to the possibility of estimating the depth to which the pyrrhotite-nickel deposit at the Falconbridge mine extended in the earth. This body is 7500 ft. long, it dips at 80° to the north, and it is fairly straight with slight sinuosities. Dr. F. W. Lee suggested that it might be possible to solve the problem by measuring the vertical magnetic intensity, with a good magnetometer, both near the surface of the earth and also at a level a 'few feet higher in the air. The writer regarded this suggestion with some scepticism, but it was decided to put the scheme to a prac¬ tical test. In July, 1930, Dr. Lee, Dr. Keys and I ' the writer, with Mr. Joyce and Mr. Belloc as assist¬ ants, made a firm, light wooden platform (Fig. 1) E measuring 4 by 4 ft. on the top, which was 10 ft. above ground. This platform could be moved easily a few yards by four men, and carried across I country in a wagon or by motor truck. Some iron nails were used in its construction, but we were not able to detect their influence on the - Askania magnetometer. Nevertheless, in future work, the use of iron should be completely avoided. Readings were taken along a traverse at right L angles to the orebody, at several stations, both on FIG. 1.-VERTICAL the ground and on the platform. The excess read- ASKANIA MAGNETOM¬ ETER ings, over the dike, as compared with those about 10 ETER ON A FT. HIGH. PLATFORM 800 ft. away, are shown in Table 1. The largest reading, 6.8, is open to suspicion and should be rejected. The depth of the top of the orebody is known by electrical survey, and by actual drilling, to be about 112 to 123 ft., and the covering is sandy glacial drift. Similar readings were taken over a long straight magnetic diabase dike. These also are shown in Table 1. The magnetic vertical intensity is consistently less at the higher level, which is l0 ft. above the lower level.

Jan 1, 1931

By Frederic K. Bunton

The smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due.to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at very hig~; efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of 81.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 Dons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by ALfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Worlrs, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913). II. Location and Connections The smelter of this company is about half a mile south of GreenGood, in the Boundary district of British Columbia, on the Columbia & Westerg branch of the Canadian Pacific Railway. It was originally built in 1900 by Paul Johnson, to handle 600 tons of ore a day in two small furnaces of 300 tons capacity; but in 1907 the old furnaces were torn out, the plant was remodeled, and three blast furnaces, 48 by 240 in. at) the tuyéres, were installed. In 1910, two of these were enlarged to 51 by

Jan 1, 1916

By R. F. Mehl, R. W. Parcel

THE rate of the decomposition of austenite in eutectoid steels, forming only pearlite, may be expressed fundamentally in terms of the rate of nucleation and the rate of growth of pearlite nodules. This matter has received much attention in recent years. (The basic references are listed in ref. 1; references of particular import to the present work will be given separately.) Systematic data have been developed for plain carbon eutectoid steels.:! Although the physical factors affecting the rate of nucleation, N, in case of plain carbon steels have presumably been identified, they cannot as yet be evaluated quantitatively.' Several somewhat successful attempts, however, have been made to calculate the rate of growth, G. In the latter case the important factors determining the edgewise growth of pearlite have been assumed to be: 1—the interlamellar spacing; 2—the concentration extremes and concentration contours of carbon in austenite in front of the growing pearlite interface; and 3—the rate of diffusion of carbon in austenite.* The only systematic data on N and G for pearlite in alloy eutectoid steels are those for Co-steels;6 there are no data on alloy eutectoid steels in which the alloying element is known to decrease the rate of formation of pearlite, apart from a few scattering data reported earlier' for steels containing manganese. This paper reports a systematic study of N and G for eutectoid alloy steels containing molybdenum and nickel, respectively. In order to provide information of help in understanding the results, new data are presented on the effect of molybdenum on the interlamellar spacing of pearlite, So; data on the effect of nickel on So have already been published.' The alloys used were in five groups: 1—Pure Fe-C-Mo alloys (Table I) were supplied by the Climax Molybdenum Company of Michigan, Detroit. They were made from Armco ingot iron of standard analysis, Acheson graphite, and ferro-molybdenum, melted in silica-lined crucibles in a high frequency induction furnace. The ferromolyb-denum was added to the melted steel, followed in 5 min by 0.08 pct Al. The ingot as-cast measured 23/4x 31/4x10 in.; it was hot-forged at 1150°C to a bar 1 in. sq.

Jan 1, 1953

By H. R. Aldrich

This paper presents some of the results obtained during the field season of 1919 while mapping, in detail, the stratigraphy of the Gogebic Range in Wisconsin. The detailed stratigraphic section for the range was first published, in 1919, by W. 0. Hotchkiss,1 State Gcologist of Wisconsin. The idea of the continuity of the definite succession thus established was the result of underground work in the productive part of the range in Michigan and Wisconsin, where most of the required data also were obtained. The bulk of the range in Wisconsin is heavily covered by drift; in fact, there is but one satisfactorily exposed section across the entire formation, few partial sections, and only scanty outcrops of any size. Evidently mapping of the detailed members of the formation could only be established at a few points; and if from these small areas the .unexposed portions were to be mapped by projection, the only apparent method for projection was straight-line interpolation modified or supported by data from the scanty outcrops and from test workings. It was found that by tracing a magnetic line, the position of which in the formation may be determined from test pits and outcrops, the projection of that member through the drift-covered areas can be accomplished. The magnetic line serves as a datum horizon within the formation to which reference may be made in correlating outcrops and ledge matter thrown from test workings. The foot wall is easily located also, and from the two datum horizons thus available and the known proportional thickness of the several members in the type sections, outcrops and artificially exposed ledges can be correlated by lithological characteristics. As a result, the tracing of magnetic lines became the basis of our work on the stratigraphy and we were able to carry the mapping of detailed members throughout the length of the range. It was found that the magnetic horizon at the base of the Tyler slate was most easily followed by the dip needle; that discontinuity caused by cross-faulting could be established; that folding along the strike could be detected in a repetition

Jan 1, 1922

By D. R. Shoemaker

BACKGROUND AND PROJECT DESCRIPTION A 16.5 kt per day underground molybdenum mine is being developed at Questa in northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. Small scale underground mining first began in 1920 and large scale open-pit mining was initiated in 1965, but because of the high stripping ratio, surface mining is being phased out. Construction of the underground mine began in 1979, and first production is scheduled for 1983. Full production of 9 Gg of molybdenum per year will be reached in 1984. Access to the mine will be through a service shaft, development shaft, and a conveyor decline. 'The service shaft, 7.3 m in diameter and 396 m deep, will be used for personnel, supplies, development muck, and fresh air intake. It will be equipped with a large, double-deck man and material cage. A double-drum hoist will be used for cage hoisting and will handle up to a 27-t load in balance with a counterweight. Development muck will be loaded into skips in balance and a single-drum auxiliary hoist will provide secondary access. The 396-m-deep, 4.3-m-diameter development shaft will be used for initial mine development, mine exhaust air, and a slick line pass for concrete entering the mine. The development shaft is located 400 m north of the service shaft. Run-of-mine ore will be transported from one of two 1.4-kt storage pockets by a 1.2-m-wide conveyor belt located in the 10°, 1980-m-long, 5.0-m-wide, and 4.6-m-high decline. The decline conveyor belt has a centerline length of 2229 m and a vertical rise of 363 m. It will be powered by four 448 kw motors driving a single drive pulley. There will be two 1.2 m transfer belts on the surface with centerline lengths of 322 m and 542 m. All three conveyor belts will be reinforced with steel cables. On the surface, in addition to the headframes and hoist houses for the two vertical shafts, a large maintenance shop, warehouse, compressor house, change house, main office building and timber framing building have been constructed.

Jan 1, 1981

By O&apos, M. M. Fine, K. G. Meara

One of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite.f In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.' The outlook for the postwar market for fluorite is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In considerbtion of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status.3 Acknowledgment This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal orc reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. 0. E. Anderson, mill superintendent,

Jan 1, 1948

By K. G. Meara, M. M. Fine, O&apos

One of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite.f In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.' The outlook for the postwar market for fluorite is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In considerbtion of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status.3 Acknowledgment This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal orc reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. 0. E. Anderson, mill superintendent,

Jan 1, 1948

By A. W. Edelen, H. V. Lee

THE Teziutlan copper-zinc deposit is supposed to be of late Cambrian or early Paleozoic age. The country rocks are a series of schists or phyllites, flat lying and in the form of a plunging anticline. The ore deposit occupies a single horizon in the schist for a known horizontal extent of 1200 meters. Along its strike occur four large lenses or ore bodies. These ore bodies occupy positions along the flank and extend to the crest of the anticline. The primary mineralization is in the form of quartz, pyrite, sphalerite, chalcopyrite and galena, with a few scattered silver anti-monides. Quartz and pyrite form the mineralization between the ore lenses. In the ore lenses the sulphides appear as a massive, very he-grained intergrowth of minerals. The intergrowth suggests a contemporaneous deposition of the heavy sulphides. The grain size, usually under 0.09 mm., makes the separation difficult and fine grinding important. The ore bodies were formed at great depth by solutions probably originating in the same basic magma that gave rise to the dolerite sills that are so common in their vicinity. INTRODUCTION The Teziutlan copper-zinc deposit is distinctly different from other ore deposits of Mexico in age and type. Previously stated to be pre- Cambrian in age, it is now quite generally supposed to belong to the late Cambrian or to the early Paleozoic period. Also, in contrast to the usual shallow-vein zone type of mineralization in Mexico, there is here exemplified an intermediate vein zone deposit of copper and zinc. So far as is known, the Teziutlan vein is unique in the history of Mexican geology and in a class by itself, its closest counterpart probably being the copper veins of the pre-Cambrian of Canada. The Teziutlan district is in the extreme northwestern corner of the State of Puebla, Mexico. Teziutlan, the terminus of a branch line of the National Railways from Mexico City, is connected to the mine at Aire Libre by a 17-km. narrow-gauge railroad owned and operated by the Teziutlan Copper Co. Owing to excessive grades on this short line, Shay-geared locomotives are used for the transportation of concentrates and supplies.

Jan 1, 1937

By John F. Kendrick, Paul D. Cornelius

This paper is a progress report of a study the authors are making of the sucker-rod pump, considered as a vibrating system with one degree of freedom, with forced vibrations and with viscous damping. Dr. S. Timoshenko's formula is given, defining such a system. Each factor is considered in respect to the problem of operating sucker rods, and the zone is pointed out in which the mathematics do not apply to the sucker-rod pump, because of its variable mass. This general theory is interpreted in the light of nearly two years of testing wells in the field, and correlating the results of other tests. The motion of the pumping mechanism is a vibration. The string of sucker rods vibrates with a natural frequency. The motion of the plunger is the result of adding together these two vibrations, and is modified by a damping or friction factor. The controlling factor appears to be the ratio of the period of the natural vibration of the rod string to the period of the vibration of the pump. The first conclusion is that a definite value of this ratio, which is below resonance and is probably not greater than 0.5, should not be exceeded in order to assure satisfactory performance from the sucker rods. The second conclusion is that the component parts of the pumping equipment should be selected to give the smallest practical period of the natural vibration, and when this does not permit operation at a safe speed and give the required plunger displacement, a longer polished-rod stroke should be used. While the quantitative results are but rough approximations, the qualitative analysis of pumping problems on this basis promises to be of considerable value in diagnosing the cause of poor performance and prescribing suitable remedies. The trouble that results, whenever it becomes necessary to crowd the sucker-rod pump, to take potentials or to handle increasing volumes of water, is responsible for the belief that this type of pump is not equal to present day needs, and that it is only a question of time before some other pumping device will take its place. Of the troubles experienced, it is not surprising that the frequency of sucker-rod failures should

Jan 1, 1937

By R. B. Kelly, Paul Martin

Central Texas added 76 producing oil and gas wells during the year, abandoned 378 wells in the same period, and produced 10,359,905 bbl. of oil in the 12 months under consideration. The oil production represents a decline of only 3 per cent as compared to 1934, but it must be remembered that much new production was added during the year. The activity in new work centered in Frio, Bexar, Williamson and Cald-well counties, with development in the Pearsall, Von Ormy and Byersville fields taking first importance. New discoveries in 1935 were confined to Pearsall area of Frio County and an extension to the Darst Creek field in Guadalupe County. The Red Lake field, in eastern Freestone County, proved itself of importance from the standpoint of a gas reserve but no oil production has yet been obtained. In Bexar County, the Von Ormy field, in which the discovery well was drilled early in 1934, completed 22 oil producers during the year. (A map of Central Texas showing location of oil and gas fields was published in Volume 114 of the A.I.M.E. Transactions.) New Fields Pearsal1.—The Amerada Petroleum Corporation, in developing its 60,000-acre block in Frio County, has definitely proved the existence of commercial oil production in four separate horizons; namely, the Navarro, the Austin Chalk, the Buda and the Georgetown. The discovery well, a two million cubic foot gas well, was tompleted in 1934. A test of the Trinity sand at 10,050 ft. found salt water but later was plugged back and finished as an oil well in the Navarro sand. Most recent of their discoveries has been in the Austin Chalk at a depth of 5666 ft., where a 24-hr. gage through 1-in. choke showed 2640 bbl. of pipe line oil. The oil has a gravity of 28.0" A.P.I. and is brownish in color. Because of lack of pipe lines in the area, the wells are produced only for short periods of time, and it is predicted that development will be slow until the district is entered by pipe line purchasing companies. Von Ormy.—In March, 1934, Umbren et al. completed their Wentz

Jan 1, 1936

By Paul Martin, R. B. Kelly

Central Texas added 76 producing oil and gas wells during the year, abandoned 378 wells in the same period, and produced 10,359,905 bbl. of oil in the 12 months under consideration. The oil production represents a decline of only 3 per cent as compared to 1934, but it must be remembered that much new production was added during the year. The activity in new work centered in Frio, Bexar, Williamson and Cald-well counties, with development in the Pearsall, Von Ormy and Byersville fields taking first importance. New discoveries in 1935 were confined to Pearsall area of Frio County and an extension to the Darst Creek field in Guadalupe County. The Red Lake field, in eastern Freestone County, proved itself of importance from the standpoint of a gas reserve but no oil production has yet been obtained. In Bexar County, the Von Ormy field, in which the discovery well was drilled early in 1934, completed 22 oil producers during the year. (A map of Central Texas showing location of oil and gas fields was published in Volume 114 of the A.I.M.E. Transactions.) New Fields Pearsal1.—The Amerada Petroleum Corporation, in developing its 60,000-acre block in Frio County, has definitely proved the existence of commercial oil production in four separate horizons; namely, the Navarro, the Austin Chalk, the Buda and the Georgetown. The discovery well, a two million cubic foot gas well, was tompleted in 1934. A test of the Trinity sand at 10,050 ft. found salt water but later was plugged back and finished as an oil well in the Navarro sand. Most recent of their discoveries has been in the Austin Chalk at a depth of 5666 ft., where a 24-hr. gage through 1-in. choke showed 2640 bbl. of pipe line oil. The oil has a gravity of 28.0" A.P.I. and is brownish in color. Because of lack of pipe lines in the area, the wells are produced only for short periods of time, and it is predicted that development will be slow until the district is entered by pipe line purchasing companies. Von Ormy.—In March, 1934, Umbren et al. completed their Wentz

Jan 1, 1936

By R. E. H. Pomeroy

THE statistical data given in this paper are taken from the actual performance of the No. 2 reverberatory furnace of the Nevada Consolidated Copper Co., Me Gill, Nev., for a period of four months, from April to July, 1914. The principal furnace dimensions are: Length, 132 ft. ½ in. at the skim-line level; average width, 18 ft., 10 in. at the skim-line level. The roof is 7 ft. above the skim-line level at the firing end. The average area in the uptake flue is 36 sq. ft., and the area above the skim line under the vulcatory arch is 24.3 sq. ft. Fig. 1 shows a diagrammatic plan and sectional elevation of this furnace. The furnace is equipped with two 400-b.h.p. Stirling waste-heat boilers set in parallel. California crude petroleum is used for fuel and has a specific gravity of 16.5° B., flashing in open test at 199° F. The oil is heated to about 200° F. in a steam heater before going to the burners, requiring about 9 b.h.p. per furnace day to heat it from the line temperature to the burning temperature. Measurement is made by oil meter, checked daily by reservoir readings. The oil is fed by gravity (34 lb. static pressure) to seven low-pressure blast burners of the Steptoe type (Fig. 2). The blast for these burners is supplied at about 40-oz. pressure by a motor-driven Connersville blower of 42 cu. ft. capacity per revolution. The air supplied by the blower through the burners for atomizing the oil amounts to about 10 per cent. of the theoretical air necessary for complete combustion of the oil. The remainder of the necessary air enters the furnace through the burner openings in the firing wall. No checker holes are provided, and the charge holes in the roof are equipped with slide gates and "dog houses? to minimize air leakages. The combustion of the fuel, as shown by gas analysis at the front of the furnace, is practically complete, the carbon monoxide in the gases being less than 0.5 per cent.

Jan 2, 1915