Search Documents

By T. D. Tiemann

Extraction of silica from the taconites of the Wisconsin Gogebic range by high temperature digestion in caustic solutions has been described.1,2 The ores consist essentially of hematite, goethite, and microcrystalline quartz, detailed descriptions of which appear in the literature.1,3 It is the purpose of this communication to describe some results obtained from a laboratory investigation of an alternative method, that of sintering the ore with sodium carbonate followed by water extraction of the sodium silicate produced. This is analogous to the Deville-Péchiney4,5 soda ash sinter process for the production of alumina from bauxites in which soluble sodium aluminates are formed. Raw mixes of the desired composition were prepared from 10.0 g minus 200 mesh samples of taconite and sintered in nickel crucibles in a muffle furnace controlled to within ±10°F of the operating temperatures. The resulting sinters were pulverized and then leached in distilled water with continuous agitation for 30 minutes at 95°C. The suspensions were vacuum filtered and the residues dried, ignited and weighed. Iron assays on the ignited samples were made by the standard dichromate procedure after dissolution in hydrochloric acid. The percentage of extraction was calculated from the iron assays by the relation:

Jan 1, 1964

By H. E. Powell, A. A. Cochran, R. E. Coleman

Infrared spectroscopy, employing the internal reflection method in conjunction with solvent extraction techniques, was used to study surface reactions between aqueous potassium ethyl xanthate and both sphalerite and precipitated zinc sulfide, each activated with aqueous copper sulfate. It was determined that reactions occurring on the sphalerite and zinc sulfide surfaces produce the reaction products ethyl dixanthogen and cuprous ethyl xanthate, some of which are adsorbed on the mineral surfaces. As the pH of the xanthate solution increased from 5.6 to 11.0, the amount of cuprous ethyl xanthate on powdered sphalerite surfaces decreased and the amount of ethyl dixanthogen first increased and then decreased. It is generally accepted that the collector potassium ethyl xanthate will not float the mineral sphalerite (ZnS). However, Gaudin1 showed that sphalerite readily floats if activated with certain metal cations before exposure to the xanthate. Copper sulfate (CuSO4) was found to be the best activator for sphalerite. The over-all flotation reagent reaction, as given by Gaudin,3 is as follows: While this is the over-all reaction, the exact mechanism of the reaction and the intermediate compounds that may be formed are not yet known with certainty. Important work has been done in Russia by Plaksin

Jan 1, 1968

W. B. PRICE,* Waterbury, Conn. (written discussion??.-It has been our experience, especially in cupro-nickel, that manganese has been very beneficial, not only, as stated by Mr. Braid, in removing sulfur, but also for its property of reducing oxides, thus making the metal more fluid, and enabling it to be poured at a lower temperature; this, in turn, prevents softening of the graphite pots and the absorption of carbon. It also acts very effectively in keeping the carbon in solution in the cupro-nickel, in the combined form. However, in the case of cupro-nickel, to obtain all these benefits it has been found necessary to keep the manganese content as near 0.25 per cent. as possible. Manganese also is very effective in diminishing the amount of blisters in cupro-nickel. So far as I am aware, both from personal experience and from the experience of others who have been engaged in the manufacture of nickel-silver and cupro-nickel, manganese used either in the form of pure metal or as manganese-copper alloy (30 Mn, 70 Cu) gives better results than any other flux. While this may seem a strong statement, manganese is the natural flux for nickel-silver and cupro-nickel.

Jan 12, 1918

By J. G. Paterson, J. A. Meech

Abstract-Activated carbon is a strong adsorbent for amyl xanthate, capable of removing from solution up to a quarter of its own weight in xanthate. In selective flotation systems where depression is unstable, separation efficiency increases with activated carbon additions. The improvements observed are brought about by two mechanisms. First, by removing stripped and residual collector ions from solution, competition between depressant and xanthate is reduced and depression is stabilized. In addition, the texture of the froth phase at high pine oil concentrations is modified by activated carbon such that better drainage between the air bubbles takes place, alleviating the mechanical entrapment of depressed mineral particles. In treating a bulk copper/lead concentrate produced from GECO ore, selectively between galena and chalcopyrite is increased when activated carbon is used. Although the rate of flotation of galena is marginally lowered by activated carbon, a small extension in the duration of flotation allows the lead recovery to increase by 19% at the same recovery of copper. An addition rate of 0.75 kg/ton (1.5 lb/st) of bulk concentrate is suggested as optimum from this testwork. However, the actual level wed in the mill is dependent upon the residual concentrations of collector and frother in the bulk concentrate Pulp.

Jan 11, 1978

By C. A. Wert

THE change in mechanical properties accompanying quench aging of carbon in a iron has been known for a number of years. Since the amount of carbon involved is rather small, however, no measurements could be made to correlate the property change with the state of precipitation of the carbide. Indeed, until a few years ago it was not plain which property might be used to indicate the state of the progress of precipitation. Some years ago the internal friction of solid solutions of carbon in a iron was demonstrated, and the use of this phenomenon to ascertain the amount of carbon in solid solution at any given time was developed. Shortly afterward the author made a number of measurements in which changes in electrical resistance, thermoelectric emf, and hardness were determined simultaneously with the internal friction (and hence with the precipitation) ? A little later Dijkstra and Wert measured the change in magnetic coercive force accompanying aging.' The present work was undertaken to inquire into the changes in yield strength accompanying aging. The work was done on specimens made of Puron. These specimens were 0.05 in. in diam and about 6 in. long. Though specimens of this small size are not ideal for yield strength measurements, such specimens are desirable for internal friction meas-

Jan 1, 1952

By C. H. Jr. Herty

IT Is well known that manganese will desulfurize molten iron through the formation of manganese sulfide, which, being only slightly soluble in the metal, rises to and enters the slag where it remains as such (mixer slag) or is converted partly or wholly to calcium sulfide (basic open¬hearth slag). The reaction by which manganese sulfide is formed is Mn + FeS = MnS + Fe. This reaction is generally considered to be reversible, although McCance1 states- that such is not the case. The experimental work was carried out to confirm the results of Rohl2 as to the reversibility of the reaction. Six trials are herein considered. In each 200 grams of electrolytic iron free from manganese and sulfur were melted in a pure zirconia crucible in a carbon resistance electric furnace. To the melted iron in runs 2, 3 and 4 metallic manganese and manganese sulfide were added to give 1, 2 and 4 per cent. manganese respectively, with 0.50 per cent. of sulfur in each. In runs 5, 6 and 7, metallic manganese andiron sulfide to give the same proportions of manganese and sulphur as in runs 2, 3 and 4, were added. The melts were held molten in the furnace for an hour and then cast into small ingots.

Jan 2, 1925

By C. G. Albert

The clay particles of 2 microns or less required for modern paper coating are predominantly flat plates, lying smoothly on the sheet and producing a high gloss. Operating speeds of today's coating machines necessitate a clay composition of 60 and sometimes 70 pct solids as against the 35 to 40 pct required in the past. Since clays in suspension may solidify in flow, only those of intrinsically low viscosity can be used as high coating solids. THE literature of paper technology contains a number of articles having reference to developments in the field of coating and filler clays for use in paper manufacture. Much of this information has not been included in mining publications and has therefore not been readily available to all in the mineral industry. Recent developments in this field, including spray drying of clays, are presented here. U. S. Bureau of Mines figures for 1952 indicate that the paper industry consumes more than 50 pct of all kaolin produced and sold in the U. S. As most of the kaolin used by the industry comes from Georgia producers, the fraction of their output destined for paper use is thus appreciably higher than 50 pct. Small wonder that the kaolin industry, especially in Georgia, is highly sensitive to the quality requirements of paper mills and must respond promptly to technological developments in paper manufacturing. The paper industry itself is not the ultimate consumer. For the greater portion of the clay the end product is the printed page, and the demands of printing and publishing have sparked some of the technological advances in paper making which have, in turn, brought about methods employed in the kaolin industry. As compared with the product of 20 or 25 years ago, one of the most striking characteristics of the graphic arts today is the mass production of quality printing of fine pictorial work, much of it in full color. During this time periodicals with printing standards close to those of yesterday's slick-paper publications that were printed on a slow schedule and for a limited circulation have grown to the point where they go out to many millions of readers, often at weekly intervals. The complexity of technological improvements brought about by this increased circulation is probably not appreciated even by technical people, unless they have had reasonably close contact with the industry. The advance has come about through developments not only in the art of printing, but also in the field of paper making and even at the level of clay mining and processing. The smoothness required for faithful reproduction of the kind of printed matter under consideration is attained with a clay-coated paper. Since the distribution expense of the publication will depend to a great extent on its weight, the paper used must not be too heavy. This means a lower basis weight than was normal for conventional clay-coated papers some 25 years ago. And for this mass production market it becomes necessary to provide a paper having these and all the other required characteristics at a very moderate price—not the premium price conventional clay-coated papers formerly demanded. This challenge has been met by a new method of producing coated paper. In the past, application of clay coating to paper was a conversion operation, performed separately from the making of the base sheet. The newer development is called machine coating. Here application of the coating is an integral step in a continuous process by which wood pulp, clay, and other ingredients are manufactured into a sheet of coated paper. Many more problems are involved in this procedural change than are apparent at a casual glance. The coating operation, for example, must function at much higher linear speed than could be obtained with coating mechanisms previously employed. The application machinery developed to meet this requirement necessitated changes in composition of the coating color.* This created new requirements, summarized below, for the clay employed as coating pigment. In addition to smoothness, a relatively glossy printing surface is needed, and to a large measure it is the function of the coating clay to make possible the development of both these surface characteristics. Traditionally, pigments such as satin-white, prepared by reacting lime with paper-makers' alum, were used to assist in producing a high finish. However, economic considerations and others preclude large-scale use of such material in the new processes. In the 1930's Maloney' discovered that a certain particle size fraction of kaolin, consisting

Jan 1, 1956

By Jacques B. Wertz

Among the parameters to be considered in the continuous search for new base-metal deposits, there often is a stratigraphic controlling factor that seems instrumental in the localization of ore. In British Columbia, for instance, the Upper Triassic as well as Lower Jurassic volcanics mixed with sediments are a useful indication in the search for copper while, in some parts of Australia, rhyolite bodies seem to be the favorable indicator, and this always within the geosynclinal environment. In Arizona, this stratigraphic factor becomes highly significant and it will be shown here that a large number of ore deposits are to be located around the flanks of ancient calcareous basins or depressions, preferentially corresponding to a certain optimum thickness as revealed by isopachs. The Martin limestone, of Devonian age, is already known for its basal O'Carroll bed which coincides with mineralization at places, and this is a relatively minor control. However, several limestone basins outlined by isopachs are in reality of greater importance as they localize mining districts. Indeed, most mines are found to coincide with a specific thickness of limestone while occurring simultaneously close to major, regional fracture intersections. The regional fractures in question were interpolated and extrapolated from known, important fault expressions, integrating quite well with the existing geology and further confirmed by minor criteria such as contacts, igneous plugs, axes of elongation of batholiths, dikes, etc. Although elements of subjectivity remain, this grid of fractures can be used quite successfully as a working hypothesis in the search for ore. Results of the present study which superposes major structural

Jan 1, 1971

By R. F. Mehl, J. T. Ransom

For many years the Metals Research Laboratory of Carnegie Institute of Technology has been concerned with the statistical nature of the engineering properties of steel from an experimental viewpoint, particularly those properties representing ductility.' In the past three years new work has been directed toward evaluating the statistical nature of the endurance properties. It has been shown that both the fracture curve and the endurance limit in fatigue are markedly statistical in nature. The S-N curve (and the endurance limit) of ferrous materials is often determined with specimens which number as few as ten. The common procedure is to test the first specimen at a stress well above the expected endurance hmit. Each succeeding specimen is then tested at a progressively lower stress, until, after five or six tests, a specimen runs ten million or so cycles without failing. Two or three more specimens are then used to find the highest stress at which failure will not occur; the limiting stress determined in this way is called the endurance limit. It has now been found, however, that the variability in the fracture curve and in the endurance limit in heat-treated alloy forging steels is so great that S-N curves must be drawn on the basis of distribution curves which can be appraised only by statistical methods. Two methods have been adopted in this study: (1) straightforward statistical studies of cycles to fracture of a number of specimens at each of a series of stress levels, and (2) a new abbreviated statistical method, known as "staircase testing."2 The latter corisists in testing a series of specimens, one by one, with the test stress for any given specimen automatically

Jan 1, 1950

J. Lainson Wills, Ottawa, Can. (Communication to the Secretary) : The localities of the Quebec and Ontario apatite deposits, and the nature of their occurrence haye been often described in the Transactions and in other publications that are readily available, and I do not, therefore, intend to discuss the many details advanced in Mr. Small's paper beyond the following two points:

Jan 1, 1893

By AIME AIME

COMPLETION of the Rainbow Bridge across the Niagara River and Gorge this fall marks a new page of achievement in the annals of bridge- building. Symbolic of the amity between two great nations, the new bridge provides an additional gateway across the most peaceful border in the world. Ground was broken for the project May 16. 1940, at a site close to that formally occupied by the Falls View Bridge which was destroyed by a record ice jam in 1938. At this point, about 2000 ft. deep and 1000 ft. downstream from the American Falls, the gorge is about 200 ft. deep and 1000 ft. wide. The great steel arch of the bridge has a span of 950 ft. and rises from its supporting abutments on the American and Canadian sides of the river to the level of the top of the gorge. This is said to be the longest hingeless arch in the world.

Jan 1, 1941

By V. GUDKOV

THE iron-ore deposits of Russia were estimated at 2,200,000,000 by the Russian Geological Survey, in 1910; but this estimate must be considered as being far too low. The estimate for Siberia, which had been explored very little for iron ore, was placed at about 27,000,000 tons. The exploration, in 1912-14, of the three iron deposits-Blagodat, Baakal and Kamensk-raised the estimate of the iron-ore reserves or the Urals from 282,000,000 tons to about 400,000,000 tons. Conservative estimates of the explored deposits made by the writer in 1915, gave the following figures: Southern Russia 900,000,000 tons, Ural Mountains 500,000,000 tons, Central Russia 900,000,- 000 tons, Siberia 100,000,000 tons, Caucasus 20,000,000 tons, or a total of 2,420,000,000 tons of iron ore, or 1,200,000,000 tons of pig iron.

Jan 1, 1921

By K. L. Fetters, F. M. Walters

ALL previous records were broken by the Iron and Steel Division, in the number of sessions, the number of papers, and the attendance. In addition to ten papers (all preprinted) on properties, structure, aid hardenability of, carbon and alloy steels, eight formal papers were presented on one or more phases of steelmaklng, and a symposium on the determination of hydrogen and nitrogen in steel. This last started at 2 p.m. and was going strong with more than a third of the audience still present at 6 p.m.

Jan 1, 1944

R. G. BROWN, Bodie, Cal.: Mr. Rickard's paper, with its valuable illustrations, brings into fresh clearness the game of hide-and-seek which the miner must play with his ore-deposit; but, more than this, it goes far towards classifying those perplexing idiosyncrasies which, while unclassified, constitute a labyrinth almost without clue. Probably every engineer can add to the list by the mention of at least one fresh detail from his own experience, and I for one would like to comment on two of Mr. Rickard's divisions. To what he has written about " walls within walls" and " walls without walls," the accompanying Figs. 1 and 2 may be appropriate, the more so as they represent conditions obtaining in a part of the Butte copper-belt more typical of the copper-veins as a whole than the Gagnon, which, in some respects the most interesting mine in the camp, stands almost alone in many particulars. (See nuns., xvi., 62.) Fig. 1 was sketched in January, 1895, in the stopes above the 700-foot level of the Colusa-Parrot mine, east of the Parrot and southwest. of the Anaconda. The stope, the commercial foot-wall of which is shown at A, was 30 feet wide at this section, the pay-ore being massive chalcocite, jumbled with bornite, pyrite, quartz and thoroughly broken-down granite. A and At are inch-thick seams of black talc; B, B' and B" are also talc, possibly 1/8-inch thick. In the plane of the section the "banded quartz " and " quartz and pyrite " were both of too low grade for extraction, but 5 feet back along the stope had been of fair value. The granite with quartz and bornite between Bt and A' was pay-ore, but that to the right of B" was not. In both cases the ferro-magnesian minerals had been removed, leaving, where not obscured by ore, faint, dark patches. Between A'

Jan 1, 1897

By J. E. Berg

THE geology of the Coeur d'Alene mining district is so familiar to every one interested in mining that I will only note as an introduction that the main producers are mines whose orebodies lie in the Revett or Burke quartzites ; that the known orebodies in the eastern part of the district all lie north of the Osburn fault; that the Prichard formation is quite generally looked upon as being unfavorable for lead deposits ; that the monzonite intrusive mass extending north from Gem to Sunset Peak, and over into Cedar Creek divide, is considered to have been the prime agent in the crea-tion of our orebodies, and that diabase dikes are a quite common feature at most of the properties with which I am familiar. Some of the exceptions to these statements may be mentioned. The Interstate-Callahan mine is considered the exception disproving the alleged relation between large ore-deposits and the Prichard formation, but this property was primarily a zinc producer, with lead secondary, though of sufficient tonnage to be a valuable product. A second interesting occurrence in the Prichard worth calling to your attention is the Jack Waite property, on Tributary Creek, north of Murray. This vein lies at a low horizon in the Prichard forma-tion, and the ore differs essentially from others in the same horizon elsewhere in that it is a clean, medium to coarsely crystalline, lead ore carrying very little zinc, about one ounce silver to ten units lead, and is accom-panied by a clean quartz gangue or vein filling. I believe that quartz was the primary mineral in the fissure, and that the lead ore was deposited in the vein as a replacement of the quartz.

Jan 7, 1927

By Herbert Hoover

NO ONE could fail to be gratified to receive so profound an approbation in his calling from the members of one's own profession. To have re-ceived this distinction from men, many of whom have been professional associates and friends over more than a quarter of a century, warrants a pride. and satisfac-tion that could come from no other source. It has often been said that men are really known only to their brothers in labor and in profession. The long friendship I have received from Mr. Saunders and the distinguished service that he has contributed to the mining industry add to my appre-ciation of this event. Mr. Kelley's remarks bring my mind easily to the beginning of that period of great advance in the engineering, profession of forty years ago. Three great forces contributed to the development of the profession. The first was the era of intense development of minerals, metallurgy; and transportation in our great West. It greatly stimulated invention; it made a demand for training and skill on the part of our engineers. The pressure of national development advanced our American practice beyond the rest of the world. Moreover, the skill of our engineers of that period owes a great debt to American educators. The leaders of our universities were the first of all the educators of the world to recognize that upon them rested the responsibility to provide fundamental train-ing in, the application of science to engineering under the broadening influence and cultivation of university life. They were the first to realize that engineering must be transformed into a profession in the highest sense, not only in the training and character but that the essential quality of a profession is the instillation of ethics. That implies not alone the job but the responsibility of the community for the job. Our uni-versities poured into our development a great stream of men with this background and training. A third distinction that grew in American engineering was the transformation from solely a technical profession to a profession of administrators-the business manager with technical training.

Jan 3, 1928

By Vernon F. Swanson

An equation has been developed which will permit the direct determination of free settling velocity of any sized particle encountered in mineral benefici-ation. The equation is based on Newton's Law with the friction factor defined as a function of the laminar boundary layer. Development of the equation is described first from an empirical trial-and-error approach. Examples are given of actual settling data from the literature versus calculated data to prove the validity of the new equation. Newton's law of resistance of a fluid to flow around a sphere is expressed in Eq. 1. Free settling velocities can be determined by setting Eq. 1 equal to the gravitational force on a particle and solving for V. Experience has shown that when the solids are greater than 1 mm in diam, or when Reynold's number for the system is greater than 800-1000, the friction factor term, fD, essentially becomes a constant, and Eq. 2-b becomes Newton's equation for free-settling and is applicable under the conditions stated. Another special condition exists for particles smaller than 0.05 mm or when Reynold's number for the system is less than three. In this case fD=24/NRor24µ/pL,dV,. Eq. 2-b can then be rewritten as

Jan 1, 1968

By John D. Morgan, Sylvain J. Pirson

AN instantaneous and continuous analysis of a mineral suspension should be of great value in controlling various mineral preparation processes. Described herein is a method of analysis based on the use of high-frequency alternating current, which, under certain restrictive conditions, could be of use. THEORETICAL CONSIDERATIONS In a suspension of conductive minerals, the electrical effect primarily responsible for the variations in electric conductivity is the capacitance. In Fig Ia, let an alternating voltage E be applied across two electrodes F and F', between which are two rows (S and T) of mineral particles, all of approximately the same size, immersed in a fluid. Let the number of rows of particles between the electrodes be R and the number of particles in each row be N. If A is the area of a particle, D is the distance separating two particles, and K is a constant depending on the fluid, the capacity, Co, of the particle system will be given by: [KRA C0 ND] Referring now to Fig Ib, let R, the number of rows, be held constant, but let N, the number of particles in each row (S and T), be increased X-fold. The capacity, C1, of [ ]

Jan 1, 1947

WILLIAM YOUNG WESTERVELT, Chairman, Representing A. T. M. E. and M. and M. Soc. of Am. ALFRED G. WHITE, Secretary, Representing U. S. Bureau of Mines. W. 0. HOTCHKISS, Representing Association of American State Geologists. DAVID WHITE, Representing U. S. Geological Survey. The organization and purpose of the War Minerals Committee was explained in a special war notice in the-August Bulletin. The first work of this Committee is to secure and condense information as to the relative importance of different properties from the standpoint of domestic mineral production. When the possibilities of ore deposits are known, involving, in some cases, further examination through the voluntary services of, Engineers and Geologists, then the necessary policy required to stimulate such development can be determined. Proper recommendation has been and will be made to .the various agencies controlling the situation during the war. This will insure a complete presentation of the needs of the situation. Every legitimate effort will be made to stimulate the production of domestic minerals and to put the industries on a permanent basis. The following information forms indicate the type of information required by the Committee. Engineers and Geologists can assist in one of several ways in furnishing information to the War Minerals Committee:

Jan 10, 1917

By K. V. Hoover, D. M. Lapham

In Pennsylvania, 310 sampled sites of clay and shale have been studied with regard to potential use, lithology, physical properties, fired properties, major-element chemical analyses, and quantitative five-component X-ray mineralogy. Approximately 80% of the samples are of some potential use. Binary correlations of test data vs. potential use indicate that certain empirically determined parameters may be critical. These are: lithology, particularly for medium to superduty refractories and lightweight aggregate; kaolinite content for refractories vs. low-temperature fired product sources; quartz analyses with an apparent necessary minimum quantity for brick; quartz content, which is low in high grades of lightweight aggregate; mica content, which is low for refractories and possibly high for lightweight aggregate; total iron, which is low for refractories and shows a 4.0% minimum for lightweight aggregate; carbon dioxide, which is low for refractories, beneficial in lightweight aggregate, and probably restrictive for some tiles; chlorite-vermicalite, which is low for refractories and possibly beneficial in lightweight aggregate. In Pennsylvania, clay and shale materials constitute one of the state's major economic mineral resources. To date, the testing program indicates considerable development potential in brick, tile, and lightweight aggregate industries and perhaps a future potential for aluminum from shales that exceed 20% AID..

Jan 1, 1972