Search Documents

By Louise Barton Freeman, Coleman D. Hunter

The total production of oil in Kentucky during the year 1943 reached 7,010,776 bbl., which is more than at any time since 1930. Of this total, 5,287,659 bbl. was produced from the counties west of the Cincinnati arch, 692,359 bbl. from the 18 new pools opened during the year, and 3,260,765 from the Smith Mills pool, which was discovered in August of 1942. This is an important increase in western Kentucky in spite of the low price of crude, and demonstrates effectively the desire of the industry to cooperate in meeting the increased demands made by the war. Western Kentucky Two deep tests were drilled in the Kentucky portion of the Mississippi Embayment this year. Both were drilled to test the St. Peter. One well, drilled in Marshall County by the Adams Oil and Gas Co., did not encounter any St. Peter sandstone but drilled 650 ft. of formation below the position of the St. Peter and above the true Knox dolomite. The other well, in Ballard County, was reported to have tested the St. Peter and to have been temporarily abandoned at 3069 ft. At this depth the well probably was stopped in about the same formation as the Marshall County well. No accurate information is available on the Ballard County well. Several new producing areas were added to the list of fields in the western Kentucky coal basin, in Daviess, Henderson, McLean, Ohio, Union and Webster Counties. The Smith Mills pool was enlarged and production was found in the McClosky (Ste. Genevieve) in addition to the Cypress sandstone from which much of the earlier production had been obtained. There was some interest during the year in testing the Devonian and Silurian formations in the area south and east of the western Kentucky coal basin. In the fall of 1943, a 15 to 20-bbl. well was drilled in Allen County and two more wells are now being drilled. The production was obtained from within a few feet of the base of the Chattanooga black shale, probably in the upper Silurian. One well in Simpson County was drilled completely through the Silurian section before it was abandoned. Several wells were drilled in Logan, Todd and Christian Counties to test the Devonian where it is thinned by removal of the upper formations before deposition of the Chattanooga shale. None of these wells was successful but several other locations are now being tested. The Silurian thins in like manner on the eastern flank of the coal basin as the crest of the Cincinnati arch is approached, and it is along this thinning edge that such fields as the LeGrande, Logsdon Valley, Magnolia, Bowling Green and the Barren County pools were developed. A number of wells were drilled around these old pools in an effort to extend them, some of which were successful. The wells listed this year in Larue, Hardin, Barren, Hart and Warren Counties were drilled in the search for other such fields.

Jan 1, 1944

By Louise Barton Freeman, Coleman D. Hunter

The total production of oil in Kentucky during the year 1943 reached 7,010,776 bbl., which is more than at any time since 1930. Of this total, 5,287,659 bbl. was produced from the counties west of the Cincinnati arch, 692,359 bbl. from the 18 new pools opened during the year, and 3,260,765 from the Smith Mills pool, which was discovered in August of 1942. This is an important increase in western Kentucky in spite of the low price of crude, and demonstrates effectively the desire of the industry to cooperate in meeting the increased demands made by the war. Western Kentucky Two deep tests were drilled in the Kentucky portion of the Mississippi Embayment this year. Both were drilled to test the St. Peter. One well, drilled in Marshall County by the Adams Oil and Gas Co., did not encounter any St. Peter sandstone but drilled 650 ft. of formation below the position of the St. Peter and above the true Knox dolomite. The other well, in Ballard County, was reported to have tested the St. Peter and to have been temporarily abandoned at 3069 ft. At this depth the well probably was stopped in about the same formation as the Marshall County well. No accurate information is available on the Ballard County well. Several new producing areas were added to the list of fields in the western Kentucky coal basin, in Daviess, Henderson, McLean, Ohio, Union and Webster Counties. The Smith Mills pool was enlarged and production was found in the McClosky (Ste. Genevieve) in addition to the Cypress sandstone from which much of the earlier production had been obtained. There was some interest during the year in testing the Devonian and Silurian formations in the area south and east of the western Kentucky coal basin. In the fall of 1943, a 15 to 20-bbl. well was drilled in Allen County and two more wells are now being drilled. The production was obtained from within a few feet of the base of the Chattanooga black shale, probably in the upper Silurian. One well in Simpson County was drilled completely through the Silurian section before it was abandoned. Several wells were drilled in Logan, Todd and Christian Counties to test the Devonian where it is thinned by removal of the upper formations before deposition of the Chattanooga shale. None of these wells was successful but several other locations are now being tested. The Silurian thins in like manner on the eastern flank of the coal basin as the crest of the Cincinnati arch is approached, and it is along this thinning edge that such fields as the LeGrande, Logsdon Valley, Magnolia, Bowling Green and the Barren County pools were developed. A number of wells were drilled around these old pools in an effort to extend them, some of which were successful. The wells listed this year in Larue, Hardin, Barren, Hart and Warren Counties were drilled in the search for other such fields.

Jan 1, 1944

By M. A. Matzkin

The Problem: There are no roads and mapping has been inadequate. There isn't a clearing large enough to accommodate a conventional airplane. Entry would consume months, yet the area must be investigated. Sustained communication is impossible except by radio. Cost in time and money for exploration would be exorbitant. . . . . . . . .

Jan 9, 1953

By Robert C. Temps

The history of iron ore milling in Chile can be divided into two periods: the first, which lasted about 40 years, ended in 1952 and the second continues today. During the first period, Bethlehem Chile Iron Mines Co. was the sole shipper and El Tofo, the only mine. That situation was forever altered in 1952 when several small independent companies began to sell ore. The success of these companies triggered programs of exploration which can only be described as a "boom" during the past five years.

Jan 1, 1963

By David A. Thomas, David N. French

The lrnrdness of WC crystals has been measured with the Knoop indenter at loads of 100 and 500 g on the (0001) and (1070) planes. The hardness as tneasitred on the basal plane is 2400 kg per sq mm and shows little anisotropy. The hardness on the prism plane, however, shows a marked orientation dependence, with a low value of 1000 kg -per sq mm when the long axis of the Knoop indenter is oriented parallel to the c axis and a high value of 2400 kg per sq mm when the indenter is perpendicular to the c axis. Slip lines (Ire observed surrounding the microhardness indentations and they show slip on (1010) planes, probably in [0001] and (1120) directions. This slip behavior can be explained by the crystal structure of TVC, which is simple hexagonal with a c/a ralio of 0.976. The hardness anisotropy call be explained by [0001]{1010} and (1130) {10l0] slii) and the resolved shear-stress analysis of Daniels and Dunn. HARDNESS anisotropy is a well-known phenomenon and has been reported for many metals, with both cubic and hexagonal structure.1-6 For hexagonal tungsten carbide, WC, a wide range of hardness values is reported in the literature. For example, Schwarzkopf and Kieffer7 give a hardness of 2400 kg per sq mm and report a value of 2500 kg per sq mm by Hinnüber. Foster and coworkerss give the average Knoop microhardness as 1307 kg per sq mm with a maximum value of 2105 kg per sq mm. Although these values and the structure of WC suggest the likelihood of hardness anisotropy, no such measurements have been made. We first detected a large apparent hardness anisotropy in WC crystals about 75 p large, in over-sintered cemented tungsten carbide. Prominent slip lines also occurred around many indentations. This report presents further observations and interpretations of hardness anisotropy and slip in WC crystals obtained from Kennametal, Inc. Both Knoop and diamond pyramid indenters were used on a Wilson microhardness tester with loads of 100 and 500 g. EXPERIMENTAL RESULTS The carbide crystals tended to be triangular plates parallel to the (0001) basal plane of the hexagonal structure. The side faces were parallel to the ( 1010) prism planes. Specimens were mounted approximately parallel to these two types of faces and metallographically polished. Laue back-reflection X-ray patterns were used to orient the specimens, which werethen ground to within ±1 deg of the (0001) and (1010) planes. The Knoop hardness values measured on the basal plane are plotted in Fig. 1. There is only a small anisotropy, with a hardness range of 2240 to 2510 kg per sq mm. The additional points at angles from 52.5 to 67.5 deg confirm the sharp minimum hardness at 60-deg intervals, consistent with the sixfold hexagonal symmetry. The average hardness of all values obtained on the basal plane is 2400 kg per sq mm. While the basal plane shows only slight anisotropy, the (1010) plane exhibits marked hardness anisotropy, from 1000 to 2400 kg per sq mm. Fig. 2 shows the hardness as a function of the angle between the long axis of the indenter and the hexagonal c axis, the [0001] direction. The minimum and maximum occur when the indenter is oriented parallel and perpendicular to the [0001] direction, respectively. The anisotropy of the prism plane is contrary to that reported for hexagonal zinc and hard- However, the basal-plane anisotropy is similar to these two metals.1'2 To check the accuracy and reproducibility of the measurements, a series of fifteen impressions was made at 100-g load in the same orientation in the same area of the specimen surface. The average for all was 2040 kg per sq mm, with a range of 1950 to 2130 kg per sq mm, giving an accuracy of about ± 5 pct. Thus the slight anisotropy on the basal plane is almost within experimental error. Fig. 3 shows slip lines around the Knoop indentations on the basal plane. The slip traces are in directions of the type (1130). The presence of slip steps on the basal plane indicates that the slip direction lies out of the (0001) plane. Because WC has a c/a ratio of 0.976,' the shortest slip vector is [0001], which suggests slip systems of the type [0001] (1010). Fig. 4 shows slip lines around the Knoop intentations on the (1010) plane. These slip lines are inconsistent with [0001] slip but can be

Jan 1, 1965

By E. C. W. Perryman

The wide grooves formed at the grain boundaries when high purity aluminum is attacked by hydrochloric acid or sodium hydroxide have been attributed by earlier workers to the high energy of the grain boundary material. The effect has been investigated for high-purity AI-Fe alloys with up to 0.055 pct Fe as a function of iron content and heat treatment. It is shown that the explanation given above is untenable, but that the results can be explained on the assumption that iron segregates to the grain boundary in solid solution. IN 1934, Rohrmann¹ showed that aluminum of 99.95 pct purity suffered intercrystalline corrosion when immersed in 10 to 20 pct hydrochloric acid, and that the susceptibility to intercrystalline corrosion depended upon the heat treatment given. The greatest susceptibility was found for specimens quenched from a high temperature (600°C) and the lowest susceptibility for specimens cooled slowly from that temperature. Lacombe and Yannaquis2 have shown that super-pure aluminum (99.9986 pct) annealed at 600°C suffers intercrystalline attack in 10 pct hydrochloric acid and that this attack is intensified by anodic dissolution in the same solution at a current density of 10 milliamperes per sq dm. No difference in extent of intercrystalline attack was found between the 99.993 and 99.986 pct Al, which led the authors to suggest that impurities played only a secondary role in the mechanism of intercrystalline corrosion. It was found, however, that the attack at the grain boundaries depended upon the relative orientation of the grains, large differences in orientation favoring rapid attack. Boundaries where the two neighboring grains were similarly orientated showed high resistance to attack as did boundaries between grains which were in twin relationship. These observations led Lacombe and Yannaquis to suggest that the intercrystalline attack was due to lattice discontinuities present at grain boundaries. Assuming that the grain boundary is a layer three to five atoms thick and has a crystal structure which is a compromise between the two neighboring grains it is clear that the discontinuities will increase with increasing difference in orientation between the neighboring grains and hence the increasing tendency to intercrystalline attack. Roald and Streicher³ investigated the effect of heat treatment of aluminum alloys ranging in purity from 99.2 to 99.998 pct on the corrosion resistance in 20 pct hydrochloric acid and 0.30N sodium hydroxide. They found that in hydrochloric acid the intercrystalline attack appeared to be determined by the type and quantity of impurities present and by the relative orientation of the grains. No difference in the susceptibility to intercrystalline attack was observed between specimens quenched and those furnace cooled, from 575°C. In 0.30N sodium hydroxide some materials exhibited intercrystalline attack, this taking the form of V-notches. Rohrmann¹ offered no explanation for the greater susceptibility to corrosion of material quenched from 600°C. It seems possible that this difference is connected in some way with a different distribution of impurity elements in the quenched and slowly cooled specimens. The fact that Roald and Streicher8 observed no difference between quenched and slowly cooled specimens may possibly be due to differences in either rate of cooling or silicon content or possibly both. Both these would be expected to have an effect on the distribution of impurity elements. Although the rate of cooling used by Rohrmann was slightly more rapid than that used by Roald and Streicher the position cannot be clarified because Rohrmann does not give the silicon content and Roald and Streicher give the silicon contents of only a few of their alloys. That Lacombe and Yannaquis2 found no difference in corrosion behavior attributable to impurities between the two materials they used may be because both were of high purity compared with the aluminum used by Rohrmann.¹ Although they found no difference in the corrosion behavior of their two materials it is possible that the results obtained by Lacombe and Yannaquis may, nevertheless, have been influenced by impurity distribution, since, on the transition lattice theory of grain boundary structure, it would be expected that sparingly soluble impurities would tend to segregate to boundaries where the orientation difference is such that there is a greater density of atomic sites of suitable size to contain them. It was considered worth while, therefore, to examine the corrosion properties of a series of materials of differing impurity content with the objects of confirming the experimental observations made

Jan 1, 1954

By P. Greenfield, C. C. Smith, A. M. Taylor

J. E. Harris (Berkeley Nucclear Laboratories, England)—Greenfield et al.11 attribute abrupt changes in slope of their log o/log i curves for heat-treated Mg/0.5 pet Zr alloy (zA) to &apos;atmosphere&apos; locking. It is proposed here that a more reasonable explanation of the apparent strengthening at low rates of strain can be based on precipitation either during the preanneal or during the creep tests. All the tests were carried out above 0.5 Tm where solute atmospheres are likely to be largely evaporated2 and can migrate sufficiently rapidly so as not to impose any &apos;drag&apos; on the moving dislocations. McLean3 has derived an expression for determining the temperature Tc above which, due to the high-migration rate of the atmospheres, Cottrell or Suzuki locking can play no part in determining creep strength. This expression, which holds for an applied shear stress of not greater than 5 X 107 dynes per sq cm is: Tc/Tm= 7/6.8 - log10? where i = secondary creep rate The values for T, corresponding to the maximum and minimum reported creep rates at each temperature have been calculated from the data of Greenfield et al. These are given in Table VII. All the test temperatures were above T,, the margin being greater for the higher temperatures and for the lower strain rates where the breaks in the log s/log ? curves occurred. Dorn and his collaborators14, 17 have studied systematically the effect of solute hardening on the creep properties of an A1/3.2 at. pet Mg alloy. In the temperature range where strain aging occurred in tensile tests, abnormally high-activation energies for secondary creep were obtained but at temperatures above 0.43 Tm, solute alloying did not have any effect on the creep parameters. Moreover, there have been no reports of any strain aging phenomenon during elevated temperature tensile tests with ZA material.18 Instead of the observed strengthening being due to atmosphere locking, it is now proposed that precipitates play an important role in enhancing the creep strength of the material. There are two possibilities—precipitation of zirconium hydride during the high-temperature preanneal and/or precipitation of the hydride or a-zirconium during creep. On the basis of the former the results can be interpreted in terms of a critical stress being necessary to force the dislocations through or over preexisting precipitates. From the latter, if the strengthening is due to pre- cipitation during the test then hardening should be associated with a critical strain rate. At low rates of strain, time is available during the tests for precipitation to occur either directly onto dislocations (thus pinning them) or generally throughout the matrix (which would impede dislocation movements). Examination of the data of Greenfield et al. suggests that both mechanisms may be operative since they observed precipitation during creep and also found that their alloys exhibited high-creep strength in the early stages of the low-stress tests, i.e., before creep-induced precipitation had time to occur. It is not easy to understand why they considered that precipitation of zirconium hydride is unlikely to occur at 600°C while it can take place in tests in air at as low a temperature as 200°C. Precipitation of the hydride during the preanneal cannot be ruled out merely on the basis of metallographic examination. Hydride precipitates in ZA type alloys are very small and can only be accurately resolved in the electron microscope.9 For example, in this laboratory20 hydride platelets with major dimensions <(1/10) µ have been observed by electron transmission through thin film specimens of hy-drogenated ZA material. Complex interactions between dislocations and such particles are illustrated in Fig. 12. Additional evidence for precipitation during pre-annealing is provided by the data presented in Greenfield&apos;s Fig. 1 and Table IT. These show that the creep strength at 200o and 400°C increases with the time of preanneal at 600°C. Such increases cannot be explained on the basis of increases in grain size alone for further improvements in strength were observed when the material was annealed for longer times than that required to stabilize the grains. Although the main discussion is confined to ZA material, similar arguments can be used against the strain aging hypothesis proposed to explain the binary Mg/Mn alloy data. In this case no precipitation is possible during the preanneal, but precipitation-hardening during creep can occur.

Jan 1, 1962

By W. R. Hudspeth

AS an outgrowth of its spodumene recovery operation at Kings Mountain, N. C., Foote Mineral Co. has been recovering a heavy mineral by-product. Foote leased this idle plant in 1951, reactivated it, using a new spodumene recovery process, and purchased plant and properties in October 1951. While the operation at Kings Mountain is primarily concerned with the production of spodumene concentrate, pilot plant work determined that the pegmatites also contained heavy minerals including cassiterite. Plans were made to recover the heavy minerals as a by-product and the flowsheet incorporated these facilities when the mill was modified for the new spodumene recovery process. The orebodies consist of spodumene, feldspar, quartz and mica. Apatite, tourmaline, and beryl are present in small quantities. The wall rock is pre- dominantly hornblende shist. The heavy minerals, including cassiterite, columbite, pyrrhotite, monazite, pyrite, and rutile represent about 0.2 pct of the ore. The fine-grained heavy minerals are disseminated throughout the dikes, apparently unassociated with the spodumene. The pegmatites are quarried and secondary breakage is by mud-capping and block-holing. Power shovels load into trucks transporting the ore to a coarse ore bin. A Telesmith 10x36-in. apron feeder delivers the ore to an 18x36 in. Traylor Jaw crusher adjusted to discharge -3 in. product to a primary conveyor. The conveyor delivers to a 4x5-ft Tyrock single deck vibrating screen using 3/4 in. cloth. The screen undersize is elevated to the crushed ore bin. Screen oversize goes to an Allis-Chalmers Hydrocone Crusher fitted with 4 in. concave and set to deliver approximately 66 pct minus 3/4 in. The crusher discharge returns to the primary conveyor. The crushing and screening installation has a capacity of about 60 tons per hour. Spirals The crushed ore is delivered at a rate of 350 tons per day to two 6x8-ft Hardinge Pebble Mills, equipped with 20 mesh Ton-Cap trommel screens. The screen oversize is pumped to a 12-in. hydroclone for primary desliming. The hydroclone underfl spirals. There is no heavy mineral loss in the hydro-clone overflow. The spirals bank consists of eight 5-turn Model 24-A Humphreys Spirals. The top port and the last four ports of each spiral are blanked, the remaining nine port splitters are adjusted to remove about 5 pct feed weight. The heavy mineral rougher concentrates are upgraded on a Deister Overstrom table. The spiral concentrates contain approximately 4 pct heavy mineral, and the spiral reject, which goes to another section of the plant for spodumene recovery, contains about 0.03 pct heavy mineral. There is an interesting feature in the spirals installation. An adjustable splitter mounted on the discharge boxes splits out a mica fines product containing very little heavy mineral. The mica product is cleaned by spiralling and screening. Thus the spirals recover two products; mica, and a heavy mineral rougher concentrate. Table Treatment The rougher spiral concentrate goes to a Deister Plato table, modified to receive a Deister-Overstrom No. 6 rubber cover with sand riffles. The table is operated with a 5/8 in. stroke, 270 strokes per minute, and a slope of 1/2 in. per ft from feed to tailings side. There is no slope adjustment from motion to concentrate end. Wash water consumption is relatively high, since the large spodumene grains tend to report with the fine heavy minerals. A middling band about 4 in. wide is maintained in order to produce clean concentrate. The middling, representing about 10 pct of table feed, is recirculated by air-lift. A band of concentrate grade coarse spodumene occurs just below the middling. This is removed and delivered to concentrate storage. The table tailing, containing approximately 0.7 pct heavy minerals, is returned to the spodumene feed preparation circuit. The heavy mineral table concentrates are approximately 45 pct cassiterite, 33 pct columbite, 14 pct pyrrhotite and 8 pct monazite, together, with some rutile, pyrite, and copper from blasting wire. Concentrate is collected at 24 hour intervals. and dried. If the concentrate remains in wet storage appreciably longer surface oxidation takes place which seriously interferes with the subsequent magnetic separation process. About 150 lb of heavy mineral concentrate is produced per 24 hours and shipped to the company&apos;s plant at Exton, Pa. for final separation into tin and columbium concentrates.

Jan 1, 1952

By S. S. Cole, H. Sigurdson

The melting points of mixtures of titanium dioxide and other titanates have been reported to a limited extent as binary systems and some results have been reported in conjunction with silicon dioxide. The limited data indicated that a low melting zone might exist in a ternary or quarternary system of CaO-MgO-TiO2-Al2O3, since the eutectics reported in the binary systems of MgO.TiO2-TiO2, Al2O3TiO2-TiO2 and CaO.TiO2-TiO2 were of about equivalent composition of TiO2. The importance of a low melting region with a high titanium oxide value in the developing of high titanium slags is fully appreciated by metallurgists. A comprehensive study was undertaken to establish basic information on low melting titanate mixtures. Compounds in the System CaO-MgO-TiO2 -Al2O3 Preparation of the titanates of CaO, MgO and Al2O3 confirmed reported data that the following compounds could be formed under oxidizing conditions in solid state reactions: CaO.TiO2, 2MgO.TiO2, MgO.TiO2, MgO-2TiO2 and Al2O3.TiO2. Under oxidizing conditions it was not possible to react MgO with TiO2 in mol ratios higher than 1:2 without having unreacted TiO2 in the product, nor was it possible to form calcium or aluminum titanates with a higher mol ratio of CaO and A12O3 to TiO2 than 1:1. By fusing mixtures of Al2O3-TiO2 and MgO-2TiO2 together a series of solid solution products were obtained, which showed an MgO-2TiO2 X ray diffraction pattern shifted to smaller inter-planar spacings. Range of Investigation Data in the literature1 indicated that these titanates had melting points which ranged from 1645 to 1860°C. Since the purpose of the study was primarily to provide useful data for smelting titaniferous ores, the work was restricted to the zone of the system which would include the crystalline phases present in the slags. The explored limits were bounded by CaO.-TiO2-MgO.TiO2-TiO2in the base plane. The system was extended to a fourth component Al2O3-TiO2 since many titaniferous ores contain appreciable amounts of A12O3. In the quarternary system CaO-TiO2-MgOTiO2-TiO2-Al2O3TiO2, a tetrahedron was used to represent graphically the components, with one component at each point of the tetrahedron. In the base plane, mixtures were pre- pared to represent fairly uniform changes of composition over the desired range expressed on a mol percent basis. Al2O3-TiO2 was brought into the system in increments of 10 mol pct up to 40 pct. Mixtures were then made up for each of the Al2O3-TiO2 planes. The ranges employed were then represented by five planes cutting the tetrahedron at 10 mol pct Al2O3-TiO2 intervals. Choice of Equipment Although it was necessary for all smelting work to be done in a strongly reducing atmosphere, it was decided that all melting point determinations should be done under oxidizing conditions. This decision was prompted by the fact that TiO2 reduced to lower oxides in a reducing atmosphere with consequent changes in melting points. The use of a micropyrometer and a platinum strip furnace for work of this type is adequately described in the literature.2 With modifications, equipment was selected which provided a fairly rapid method of determining melting points of refractory oxides. The final assembly, which was used, consisted of a platinum strip furnace and a Leeds and Northrup disappearing filament optical pyrometer attached to a special telescope which magnified the sample about 20 diam. The furnace assembly consisted of a platinum strip 0.005 X 0.3 X 2.2 in. mounted on brass posts on a refractory base. This was enclosed in a black steel shell which had a 2-in. opening at the top for purposes of sighting the telescope. The platinum strip was in series with two 0.04 ohm nichrome resistors connected to the secondary of a 2 kw transformer which supplied 17 volts. The current to the primary was varied

Jan 1, 1950

By W. J. West, T. D. Mueller, J. E. Warren

The authors have presented valuable information on the influence of the interfacial tension and the contact angle on the recovery efficiency of the waterdrive process. It is considered, however, that the following points deserve a closer examination. 1. As pointed out by Wyllie and Spangler1 the displacement pressure PD i.e. the pressure required to initiate the displacement of the wetting phase from the core, is a measure of the maximum pore diameter dmax. If the capillary pressure Pe as a function of the wetting

Jan 1, 1956

By H. W. Hitzrot, R. H. Limons, L. V. Fegan

The testing of a new method for measuring pellet-bed temperatures in the traveling-grate or shaft furnace is presented in this paper. This method, using silver-palladium alloy wires as indicators, overcomes disadvantages existing in the methods based on the use of thermocouples which are costly and time-consuming. The authors have developed and tested a new method for measuring pellet-bed temperatures in the traveling-grate or shaft turnace through the use of silver-palladium alloy wires as indicators. This method overcomes the disadvantages of existing methods, which, based on the use of thermocouples, are generally costly and time-consuming. For example, in the case of the traveling-grate furnace, the installation of an instrumented pellet, together with its attached thermocouples, requires stopping the furnace, with resulting loss of production time. As for temperature measurement in the shaft furnace by the existing method, the movement of the shuttle-car feeder seriously interferes with both the actual insertion and the resulting distribution of continuously fed thermocouples. The authors have overcome these difficulties by using, as temperature indicators, a range of silver-palladium alloy wires that can be easily recovered, after firing at any desired location in a pellet furnace. Silver-palladium wires having specific melting points from 2000°F to 2500°F are enclosed in ceramic capsules. Each capsule is placed in a ni-chrome wire basket filled with a sample of green pellets, the baskets being the means for recovering the capsule after firing. After the encapsulated wires have been exposed to the firing cycle, the alloy wires are examined to determine the maximum temperatures attained by the pellet sample. This method gives accurate, rapid determinations of maximum temperatures attained during pellet induration in either the traveling-grate or shaft furnace The new method has the following advantages over existing methods: 1) it is less expensive; 2) no furnace downtime is required; 3) the testing units can, be made in quantity in advance; 4) measurements can be made in rapid succession at all desired locations; 5) measurements of maximum firing temperatures are more accurate; 6) on the basis of points 4 and 5, the new method gives a more reliable picture of the correlation of pellet quality, petrographic textures and maximum temperatures, thus providing a more effective quality-control tool. A disadvantage of the method is, of course, that the measurements are not continuous and only maximum temperatures are determined. TEST PROGRAM Preparation of Materials: CALIBRATION OF ALLOYS - In the following discussion the term "bead point" (see Fig. 1) refers to the temperature at which each alloy begins to melt and form a bead. Fig. 2 gives the bead point curve for silver-palladium alloys. Before the alloys are used in plant tests, the bead point of each alloy should be determined in the laboratory to verify the alloy compositions. Once a given alloy has been calibrated, it can be

Jan 1, 1965

Iron and steel lire subjects that will receive the attention clue them at the meeting in. St. Louis. Within the past 2 years the smelting of iron ore on a large scale has been started in the St. Louis area, and the blast furnaces are in full operation. Ore is being received. from the Lake Superior region, in large barges .brought clown the Mississippi River. Firebrick, for the lining of the furnaces, is made in the. St. Louis district to a greater extent than elsewhere in the country. At this meeting, there will probably be a discussion of the possibilities of the increase of manganese production in this country, and of improved methods of using it in steel manufacture.

Jan 10, 1917

By F. W. Jessen, James N. Howell

INTRODUCTION The determination of cloud points has to date been limited to rather transparent oils, visual observation of the formation of a solid phase being the criterion for the standard ASTM D 97-47 method. The need for a quiclc and simple method for determining cloud points under dynamic conditions for opaque crude oils became necessary in a study of fundamental aspects of paraffin deposition from crude oils. PREVIOUS WORK The determination of cloud points in opaque oils by viscosity temperature curves is fairly new, Young&apos; described a method employing the capillary tube principle. No information exists relative to the determination of cloud points of crude or refined oils under dynamic conditions. Shock&apos; noticed that deposition of paraffin from crude oils took place at temperatures at or below the temperature at which a sharp inflection point occurred in the viscosity-temperature curve. This observation indicates a possible correlation between this temperature and the cloud point of the crude oil. Reistle and Vietti1 have reported that when crude oils containing small amounts of asphaltic materials were heated to temperatures sufficiently high to solubilize these materials and immediately cooled the pour point of the crude oil was lowered as much as 70°F. Sachanen\ asribes this effect to the action of colloidal asphaltenes in preventing the formation of the crystalline structure necessary to maintain the oil in a rigid state. At high temperatures, asphaltenes are peptized, and the paraffin crystals formed at these temperatures adsorb the colloidal asphaltenes on their surface thereby hindering further growth of the crystals. Reistle" found, however, that such heating and cooling of crude oils had no effect upon the cloud points. This latter work dealt with a crude oil of fixed composition, and the question immediately arises as to the effect of varying the concentration of asphaltic materials on the cloud point. APPARATUS AND PROCEDURE All viscosity measurements were made with a Bendix Ultra-Viscoson. The Bendix Ultra-Viscoson, which consists of a vibrating probe and an electronic computer. measures viscosity by exciting a thin alloy steel blade on the end of a probe by short electrical pulses in damped oscillation at 28 kilocycles. The blade vibrates longitudinally with an amplilude of less than 55 micron or 20 millionths of an inch. Energy to protlucc this excitation is generated in he computer and transferred to the probe through the connecting cable. The oscillating blade is magnetostric-tive, i.e., it is capable of transforming electrical energy to mechanical energy in the ultrasonic range. Ultrasonic waves are produced in the material surrounding the blade by the oscillating motion of the blade causing layers of the material to slip back and forth over one another at a known frequency. The electronic computer calculates the energy required to produce the sliding motion which is in turn proportional to the viscosity of the material. Actual values of viscosity times density (centi-poise X grams/cc) are indicated on the computer and a continuous D-C signal is provided which is fed into a type 153 Electronic Recorder (manufactured by Brown Instruments Div. of Minneapolis-Honeywell Regulator Co.) The liquid sample container was fabricated from a Lucite cylinder and jacketed by a Luicite water bath. Early experiments using glass and steel sample containers were not satisfactory. since the Ultra-Viscoson was apparently affected by the alterzltion of the magnetic fields surrounding the probe by stresses set LIP in the glass and steel as it cooled. The procedure for determining viscosity-temperature curves was relatively simple. The temperature ot the sample was raised sufficiently high to solubilize all paraffin and asphalts present. After heating, the oil sample was immediately transferred

Jan 1, 1957

By Chas. Kohl

ABOUT 1929 an engineer was engaged to organize a Safety Department, lay out an educational program, and achieve a reduction in accident frequency. Due to the large number of employees, about 12,000, and the distances between the various properties, it was a big undertaking. Most of the workmen are from the Sierra and for generations have been agricultural people, with little conception of modern tools and machinery, and to a large degree are illiterate. However, gratifying results have been obtained, as evidenced by the accident frequency curve during the sixteen-year period. Safety offices have been established in each of the six major properties, staffed by men who devote their entire efforts to inspections of working conditions and equipment, instructions as to safe methods, and investigations of accidents. The Corporation is a member of the Inter-American Safety Council, receiving their publications and literature, which serve to keep us up to date and informed on modern methods. Dissemination of this material is accomplished chiefly through word-of-mouth and bulletin boards. When it is found that the accident rate is increasing in a certain occupation, as for instance underground haulage or mine hoisting, the operators so engaged are assembled and given renewed instructions on the safety code pertaining to their work. Inter-camp competitions in accident avoidance are being conducted, with annual awards for that unit having the lowest severity rate for the year.

Jan 1, 1945

By J. D. Hunt, D. T. J. Hurle

A uariety of eutectic structures are formed in faceted/nonfaceted eutectics. The various structures are explained in terms of the absence or presence of small facets in the liquid groove. Regular structures are produced when, for purely geometric reasons facels cannot form. The presence of a facet in the liquid groove leads to the formation of an irregular or a cell-like complex regular structure, due to the relative immobility of the groove. A classification of eutectics was proposed by Hunt and jackson, based on the presence or absence of facets on the primary phases (the absence of facets may be predicted from the dimensionless entropy of melting2). Eutectics were divided into three groups: 1) eutectics in which both phases grow in a nonfaceted manner; 2) eutectics in which one phase grows faceted, the other nonfaceted; 3) eutectics in which both phases grow faceted. It was suggested that regular1 rodlike or lamellar structures1 should be formed in the first group, that irregular or complex regular structures1 should be formed in the&apos; second, and that irregular structures1 should be formed in the third. Recently it has been shown that the structural classification is incomplete. Regular rodlike structures (InSb-NiSb eutectic3), or broken lamellar structure (Bi-Zn eutectic, Fig. 8), are formed in alloys of the second group when the faceted phase has a large volume fraction. Hunt and jackson&apos; argued that regular structures could form in faceted/nonfaceted systems, but that such structures would be unstable in the presence of microfacets on the lamella of the faceting phase, because the growth rate at a point on such a facet would depend on the kinetic undercooling at the point of nu-cleation on the facet, and not on the local kinetic undercooling. In these circumstances it would not be possible to consistently balance the compositional and kinetic undercooling over a lamellar structure and thus obtain a stable isothermal interface. In this paper we discuss in detail the origin of the various structures formed in faceted/nonfaceted systems, pointing out that the most important factor promoting the formation of a regular structure is the absence of a facet in the liquid groove. 1) FACET FORMATION IN SINGLE-PHASE MATERIALS Facets form when there is an energy barrier for the addition of a new solid layer on an existing solid. When a barrier is present,2 growth proceeds by the lateral movement of steps across a crystallographic plane. The rate-controlling stage of the process occurs when the step is first formed. Hulme and Mullin6 have shown that faceting in single-phase materials can only occur when both interface curvatures are convex with respect to the solid and when the surface is tangential to the facet plane. When even one of the curvatures is concave a facet does not form because new layers of solid from adjacent regions can always feed the facet plane, Fig. 1. Growth under these conditions is then as easy as elsewhere. Similar considerations will apply to eutectic growth; consequently the shape of the faceted phase is extremely important. 2) LAMELLAR SPACING CHANGES IN EUTECTICS Jackson and Hunt7 have shown that the interface undercooling AT of a growing lamellar interface (neglecting kinetic undercooling) is related to the lamellar spacing, A, and growth velocity, v, by an expression of the form: where m, Ql, and nL are constants of the system given in Ref. 7. Eq. [I] is plotted for fixed v in Fig. 2. Jackson and Hunt postulate that a regular eutectic grows near, but to the right of the minimum in the AT vs A curve. They argue that the spacing cannot be to the left of the minimum because the interface is then unstable to fluctuations in A. It cannot grow too far to the right, because when the spacing becomes too wide an isothermal interface can no longer be maintained over the large-volume-fraction phase.7 It is argued that during any change in growth rate the lamellar spacing remains in the permitted range by the movement of lamellar faults. When the spacing is too wide, the fault, shown in Fig. 3, moves to the left; when the spacing is too narrow it moves to the right. The faults, however, have to be formed. heir formation has been shown to occur when local regions deviate considerably from the spacing defined by the lamellar When the spacing is locally too narrow (it passes to the left of the minimum, Fig. 2), pinching off of the narrow phase occurs. When the spacing is locally too wide, the interface on the large volume-fraction phase can no longer be maintained as an iso-

Jan 1, 1969

By E. P. Abrahamson

The effect of transition element binary solid solution additions upon the recrystallization temperature of titanium has been investigated. All additions, except columbium and tungsten, raised the recrystallization temperature. A correlation is obtained between the logarithm of the absolute rate of change of recrystallization temperature with atomic percent solute and the number of uuter d shell electrons attributed to the free atom of the solute element in its ground state. The work of Abrahamson, et aL.1-6 on dilute binary solid solution alloys indicated a correlation between the free atom ground state electron configuration of the solute and both the brittle-ductile transition and recrystallization temperature. It is shown in these studies that the number of outer s and d electrons in the solute are of prime importance in determining the absolute rate of change of recrystallization or transition temperature with composition. Furthermore, the limit of initial linearity (in the curve of recrystallization temperature vs at. pct solute) has been shown to be a function of the number of d shell electrons in the solute for dilute iron- and vanadium-base alloys. To date no complete systematic recrystallization study of dilute binary titanium base alloys has been made. This study together with that of zirconium base alloys 6 will provide the data for the comparison of the effect of the same solutes upon two solvents with the same number of outer d shell electrons.

Jan 1, 1962

By Rizzi Homestake Mining Co.

Geophysical methods of discovering new mineral deposits have long been routine with both the petroleum and mining industries. Experience has shown that most subsurface structures and mineral deposits can be located, provided that detectable differences in physical properties exist. The main properties exhibited by the more common rocks and formations are: density, magnetism, electricity, electrical conductivity, and radioactivity. This entails five major geophysical methods: gravitational, magnetic, seismic, electrical, and radiation. Applications of radioactivity measurements in geophysical exploration are concerned with location of concentrations of radioactive rocks and materials, such as uranium. The search for uranium ores and minerals has been carried on for more than 50 years, ever since the first atomic breakdown from uranium to radium was discovered. However, the comprehensive search now being made throughout the world for radioactive materials is a direct result of the first atomic explosion and the subsequent development of new and more sensitive portable equipment to detect radiation.

Mar 1, 1956

By Auguste J. Rossi

As is well known, practically all the phosphorus of the ironores smelted in the blast-furnace passes into the pig-metal, increasing its fluidity, but diminishing its strength to such an extent that, if phosphorus exceeds a certain amount, the metal is only fit for fine castings, not required to resist strains, and it cannot be used for the ordinary purposes of good foundry-iron. No phosphorus being eliminated in the acid Bessemer process, the quantity admissible in pig-metal destined for that process must be very small, and hence the ores smelted must be strictly Bessemer ores, of which, in many districts, the supply is taxed to the utmost. On the other hand, very highly phosphoric pig, a metal of little or no value by itself, when refined by the Thomas-Gilchrist process in the basic converter, furnishes an excellent steel; but such pig-iron must be made from ores particularly high in phosphorus; and these ores are not everywhere abundant, and are much sought after for this special purpose. But there are many iron-ores containing a moderate, though still important, amount of phosphorus, which yield a pig-metal

Jan 1, 1897

By H. W. Immolz

The Palo Pinto limestone pools of Jones and Shackelford Counties were defined and almost fully developed during the year. A new Palo Pinto limestone pool was apparently discovered when the K. B. Nowels NO. 1 Pardue, S.F.I. and W. survey, south central Haskell County, was completed for a small well in Palo Pinto limestonc at 3395 to 3421 feet. In Haskell County, Amerada Petroleum Corporation&apos;s C. J. Kleiner, J. M. Cass survey, drilled to the Ellenburger with a total depth of 5607 ft., where it was abandoned. A Bluff Creek sand field of undetermined size was discovered by the Fain-McGaha No. 1 Dawson-Conway, P. G. Holcomb survey, which was chompleted for 37 bbl. at 1496 feet. The Cook field was extended by the Roeser-Pendleton B-113 Cook in sec. 113, E.T.R.R. Co. survey, the well being completed for 510 bbl. from Cook sand encountered at 1545 to 1568 feet. Several shallow pools of minor importancc mere also discovered in Shackelford County during the year. In Jones County the Lewis and the Steffens fields, in block 15, T. and P.R.R. Co. survey, were further developed during the year but the limits of the Steffens field were not definitely defined. The most, important discovery in Jones County was the Guitar field, where most of the wells that had been producing from the Cook sand were deepened to the Hope limestone, a new producing horizon. In Taylor County, the Bowles field, see. 28, B.A.L. survey, was defined arid proved to he of minor importance. The Goldsboro and Novice area, ill northwest Coleman County, continued to hold considerable interest because of the developments near the town of Novice, where new Ieases continued to be opened for production. Nolan County was placed in the ranks of the producing counties when the S. B. Owens No. 1 Tipton, sec. 43, block 19, T. and P.R.R. Co. survey,

Jan 1, 1940

By H. W. Immolz

The Palo Pinto limestone pools of Jones and Shackelford Counties were defined and almost fully developed during the year. A new Palo Pinto limestone pool was apparently discovered when the K. B. Nowels NO. 1 Pardue, S.F.I. and W. survey, south central Haskell County, was completed for a small well in Palo Pinto limestonc at 3395 to 3421 feet. In Haskell County, Amerada Petroleum Corporation&apos;s C. J. Kleiner, J. M. Cass survey, drilled to the Ellenburger with a total depth of 5607 ft., where it was abandoned. A Bluff Creek sand field of undetermined size was discovered by the Fain-McGaha No. 1 Dawson-Conway, P. G. Holcomb survey, which was chompleted for 37 bbl. at 1496 feet. The Cook field was extended by the Roeser-Pendleton B-113 Cook in sec. 113, E.T.R.R. Co. survey, the well being completed for 510 bbl. from Cook sand encountered at 1545 to 1568 feet. Several shallow pools of minor importancc mere also discovered in Shackelford County during the year. In Jones County the Lewis and the Steffens fields, in block 15, T. and P.R.R. Co. survey, were further developed during the year but the limits of the Steffens field were not definitely defined. The most, important discovery in Jones County was the Guitar field, where most of the wells that had been producing from the Cook sand were deepened to the Hope limestone, a new producing horizon. In Taylor County, the Bowles field, see. 28, B.A.L. survey, was defined arid proved to he of minor importance. The Goldsboro and Novice area, ill northwest Coleman County, continued to hold considerable interest because of the developments near the town of Novice, where new Ieases continued to be opened for production. Nolan County was placed in the ranks of the producing counties when the S. B. Owens No. 1 Tipton, sec. 43, block 19, T. and P.R.R. Co. survey,

Jan 1, 1940