Search Documents

By W. C. Winegard, J. R. Carruthers, A. Plumtree, L. R. Morris

The unidirectional solidification of dendrites containing central twin planes was studied in A1-Ti alloys. Once nucleated, the twinned dendrites are a Twore ejficient form for solute redistribution and therefore grow in preference to the normal columnar dendvites. Comparison of these twinned dendrites to adjacent colunmar dendrites by means of decanting experinzents and electron-probe rnicvoarmlysis indicates that these special dendrites grow with less undercooling than normal dendrites. These findings are further supported by the effect of forced convection on the dendrite morphologies. COMMERCIAL semicontinuous cast ingots of most aluminum alloys frequently exhibit large grains which appear to be composed of hundreds of parallel, continuous, thin lamellae. This structure has been termed "basaltic",' "fiederkristall", or, commonly, "feathery grain". The lamellae are 'about 100 p thick, several inches long, and each lamella contains a central (111) coherent twin boundary. The feathery grain has been reported to have a (112) direction2 and a (110) direction4 in the twin plane parallel to the casting direction, in contrast with the usual columnar structure where a (100) direction predominates. Aust et uZ.~ proposed that the twin boundaries were growth twins nucleated by stacking faults on the octahedral planes. chalmers6 has suggested that feathery grain may grow by a re-entrant edge mechanism, as proposed by wagner7 for twinned dendritic growth in germanium. Cahn et ~1.~ have concluded that the occurrence of feathery grain is evidence of some form of lateral layer growth rather than the atomically continuous growth normally observed in metals. The postulates by Chalmers and Cahn would seem to be contradicted by the work of Nakao~"' who showed that feathery grain only occurs when growth rates are high and the aluminum contains some solute. Specifically, Nakao found that in order to obtain feathery grain, in small castings solidified unidirec-tionally upward, the rate of growth must be above 2.4 cm per min and a critical solute concentration must be present. Below this solute concentration the grain structure was totally columnar. The critical solute concentration was found to be approximately: 0.04 wt pct Ti, 2 wt pct Cu or Mg, and 8 wt pct Zn. As pointed out by Chalmers it is not obvious why a twin-plane re-entrant edge mechanism would occur in aluminum which is thought to have a diffuse solid-liquid interface. The present experiments were undertaken to determine the growth mechanisms in- volved and to study the solute segregation in more detail. EXPERIMENTAL PROCEDURES Alloys ranging in composition from 0.05 to 0.23 wt pct Ti* were prepared from 99.9 pct pure Ti and 99.993 pct pure Al. Two-hundred-gram samples of A1-Ti binary alloys were solidified unidirectionally and vertically upward from a water-cooled copper base, in a heated insulated mold. The 1-in.-diam, 6-in.-length mold was made of Marinite (manufactured by Johns-Manville Co.). The mold was attached to a 24-in. pivoted arm such that by dropping a weight the mold was rotated 180 deg, throwing the liquid metal from the solid. In this way, the solid-liquid interface was revealed by decanting. A sketch of the decanting mold is shown in Fig. 1. The alloy was poured into the mold at temperatures ranging from 680" to 750°C, partially solidified by water cooling from the base, and decanted after a measured time interval. Growth rates for each metal-pouring temperature were calculated from solidification-time vs length solidified curves. Temperature gradients in the melt were measured using four No. 34 gage thermocouples which protruded into the mold cavity. Grain orientations were determined by X-ray diffraction using Laue back-reflection techniques. Grain substructures were examined metallographically, using polarized light, by applying a thin epitaxial anodic film to polished sections after the method of Hone and pearson." Titanium micro segregation was measured by electron-probe microanalysis using a NORELCO AMR/~ with a mica crystal and proportional-flow counter. Several of the cast samples exhibited feathery and columnar dendrites growing in the same direction and

Jan 1, 1967

By F. Bonaccorso, G. Venturello, C. Antonione

A study of the effect of small amounts of interstitial impurities on recovery and re crystallization in high-purity iron (99.995 pct) has been undertaken. This paper gives results on the effect of carbon, introduced in small-dosed amounts @om 0.0005 to 0.0086 wt pct) by heating iron specimens of high purity m a static atmosphere of CO + ,. The materials prepared in this way, cold-worked 80 pct and subjected to a series of isochronal and isothermal annealings, were submitted to examinations by X-rays, micrographs, and hardness tests. It was observed that effect of carbon is remarkable in the sense of blocking recovery of mechanical properties up to the temperature at which re crystallization begins. On the contrary, carbon has a negligible effect on primary re crystallization temperature, when compared with the known effect of substitutional impurities. This is in agreement with the high mobility of interstitials. In effect, only a slight decrease, -20 pct, of the grain-boundary motion rate was noted, due to the interaction between the grain boundary and the carbon atoms. On the other hand, in the samples in which the carbon content is above the solubility limit at the temperature at which re crystallization occurs, a slight increase of nucleation frequency is noted due to the presence of precipitated carbides. ThE effect of purity on recovery and recrystalli-zation phenomena has been known for a long time; however, recently, new attention has been given to the problem since new methods for obtaining metals with extremely low impurity contents have become available. Most of this research work essentially concerns the effects of impurities which cause precipitates or give rise to substitutional solid solutions. The works of Bolling and winegard1 and Aust and utter' on lead, and Vandermeer and orddon' on aluminum, 01sen4 on nickel, and Abrahamson and Blakeney on iron should in particular be referred to. On the effect of this type of impurities a quantitative theory has been formulated by Detert and Lucke6 and has lately been discussed critically by Cahn7 and Gordon and vandermeer.' Interstitial solid solutions in iron have not as yet been studied. As the study of the effect of interstitials is of great interest both from a theoretical and practical standpoint, it was deemed useful to examine the effects of carbon, nitrogen, and boron on recovery and primary recrystallization of iron. There already is some work by Chaudron et al.,1-" on the effect of interstitials on iron; their work, however, mainly concerns secondary recrystallization. The present paper refers in particular to the effect of carbon. EXPERIMENTAL PART Preparation of Materials. The pure iron used for this research was obtained from FeCIS recrystal-lized and purified by extraction with isopropylic ether. From the ferric chloride purified in this manner, hydroxide was precipitated with a solution of very pure ammonia, and, by calcination in pure sintered alumina crucibles, oxide was obtained. Reduction of the oxide to iron sponge was performed in sintered alumina tubes with very pure hydrogen at 650°C; at the end of the operation temperature was increased to 900°C. Specimens for the experiments were obtained by sintering the sponge at 1480°C in pure Hz after a pre sinter ing treatment at 900° C. It is important to note that the treatment at 1480°C in Ha produces a further purification from more volatile elements such as zinc, cadmium, arsenic, lead, and tin. Details on the preparation and characteristics of this type of very pure iron are given in a previous work.'' Only the complete analysis performed by neutron-activation methodsz3 is given here, Table I. Some of the specimens prepared in this way were carburized in the 0 region with very low amounts of carbon by treating them at 700°C in a static atmosphere of Ha containing a definite amount of CO. The set-up used is described in Fig. 1. A gas-tight quartz tube containing the specimen to be carburized and an internal friction control specimen, after being evacuated, was filled with Hz

Jan 1, 1963

By F. G. Miller

Earlier studies of the mechanism of flotation showed that coal flotation products are contaminated by composite coal and mineral particles. The mineral matter of these particles has the dual effect of increasing the specific gravity and decreasing the coal surface of the particle available for bubble attachment. The present study showed that these particles are more loosely held in the froth column than the high grade coal particles, especially in the coarser sizes. Consequently, it is possible in the laboratory to produce a secondary concentration of the product by sprinkling the froth product with water to wash these loosely held particles from the froth during formation and recovery. To improve coal flotation, Bethlehem Steel Corp.'s research department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies1 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the basis for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14 mesh x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level. These principles and findings, together with work by Professor V. I. Klassen,' led to the froth sprinkling investigation reported in this paper. Working with Russian coals, Klassen had shown that froth sprinkling washes loosely held refuse particles from the froth and compensates for the water lost in the upper froth layers and increases its stability. As a result, the coal particles are retained in the froth and the loss of coarse coal from the froth is prevented. Decreases in ash of 0.1% to 1.5% were reported by Klassen. Working with a 28 mesh x 0 American coal, the author of the present paper found that single-stage flotation coupled with froth sprinkling produced a product comparable to that obtained by the more expensive method of roughing and cleaning.3 The investigation reported in the present paper expanded study of the effect of froth sprinkling to include each of the standard size fractions of a bituminous coal. The main findings are as follows: (1) For those size fractions between 48 mesh and 150 mesh, froth sprinkling produces a marked reduction in both sulfur and ash. In the case of those sizes coarser than 48 mesh, while this reduction is not as significant, the additional benefit of shorter retention time is still a plus for froth sprinkling. Furthermore, when froth sprinkling is coupled with normal fast flotation, the product purity approaches that obtained by starvation reagent feeding, i.e., gradual feeding of flotation reagent to float the recoverable coal from the pulp slowly in several increments. The specific results for these two size groups are: (a) 14 x 48 Mesh. By using froth sprinkling with fast flotation, product sulfur can be reduced to a level

Jan 1, 1970

By J. L. Walter, W. R. Hibbard

A GREAT deal of work has been done on the rolling of single crystals of iron. Barrett and evensoon studied end orientations of heavily cold-rolled iron crystals and found that some crystals maintained a sharp single orientation during rolling. Others rotated into two or more orientations, and some fragmented and approached the entire polycrystalline texture depending on the original orientation of both the normal and rolling directions. Barrett, Ansel, and Mehl2 studied iron-silicon alloys and found that the addition of silicon to the iron had little effect on heavily rolled polycrystalline material. Dunn3 has extensively studied the cold-rolling and recrystallization of silicon-iron single crystals. Dunn found that for single crystals having initial orientation between (110) [001] and (111) [112], the principalcomponent of the cold-rolled texture is (111) [112]. Koh and Dunn4 studied the cold-rolled textures of single crystals having initial orientations in the range (001) [110] to (111) [IT01 and found that these are stable end orientations. They also found that all orientations having a [110] direction parallel to the transverse direction rotate to either the (001) [110] or the (111) [112] stable end orientation except for orientations near (112) [11], which divide and produce a final texture consisting of (001) [110]and (111) [112] components. Crystals having a (111) <112>-type texture re-crystallized to a (120) [001] or (110) [001]-type texture. Crystals having orientations with a range of (001) to (335) in the rolling plane and [110] in the rolling direction recrystallized5 to a wide spread of the initial orientations resulting from a multiplicity of 30-deg rotations about several (110) poles. The present study was undertaken to relate other orientations of crystals of silicon-iron to their cold-rolling and recrystallization textures, so that one might rationalize polycrystalline recrystallization data on the basis of the known deformation texture and the behavior of single crystals in these orientations. PROCEDURE Samples were obtained from a cylindrical ingot of 3 pct silicon iron prepared as follows: Armco iron was melted with high-purity silicon flakes under an atmosphere of argon to minimize oxidation. The alloy was poured into a special mold to form an ingot which consisted partially of large columnar crystals. Plates were cut from the columnar portions of the ingot with the longitudinal direction parallel to the columnar axes and ground to 0.040 in. thick. The plates were heavily etched to a thickness of 0.032 in. to remove the cold-worked surface. Orientations of seventeen crystals were determined by Laue back-reflection techniques keeping the mean columnar axis as the reference direction. The plate was then cut in two, parallel to the columnar axis. One portion of the plate was rolled at room temperature parallel to the columnar axis to a reduction in thickness of 84 pct. The remaining portion of the plate was rolled also at room temperature across the columnar axis to a reduction of 66 pct, at which point the crystals began to separate at the boundaries. After rolling, nine individual crystals were removed from the strip by cutting along the crystal boundaries with a jeweler&apos;s saw. Fig. 1 shows the original orientations of the six crystals that were straight-rolled and of the three crystals (4, 7, and 8) that were cross-rolled. Each rolled crystal was carefully etched to approximately 0.002 in. thick. Textures of the cold-rolled crystals were determined by use of the diffractometer with a non-integrating sample holder. The pole figures were made for the (200) poles using molybdenum Ka radiation and were plotted by an automatic stereographic projection recorder.&apos; Spurious poles were determined by rerunning portions of the pole figures using strontium oxide to filter out the Ka radiation. The central portions of the pole figures have not been determined. The pole figures were completed to about 55 deg from the periphery at which point the sample holder interfered with passage of the beam. Following the determination of the cold-rolled

Jan 1, 1959

By J. F. Martin, J. E. Friedline, L. M. Melnick, G. E. Pellissier

A method has been developed for determining gases in steel in which the gases are extracted by vacuum fusion and analyzed by mass spectrometry. This method is especially applicable for determining small amounts of oxygen and nitrogen. The lower limit of detection for both oxygen and nitrogen is 0.0001 pct with an average deviation of about 0.0001 pct for oxygen and 0.00008 pct for nitrogen. Hydrogen analyses by this method are in good agreement with analyses by vacuum tin-fusion. A complete analysis of all gases extracted from a steel sample can be accomplished in 40 min. It has long been known that certain of the gaseous elements exert particular effects on the physical and mechanical properties of steel. With the recent advent of new experimental steelmaking practices it is now possible to obtain steels with extremely low contents of such elements as oxygen and nitrogen. Present methods for determining these two gases are of insufficient sensitivity as applied to steels made by these newer practices, and therefore a new technique was considered necessary. A review of the literature showed that the conventional vacuum-fusion method1 was the procedure most suitable for modification to obtain a sensitive method for determining the gaseous elements present in steel simultaneously. However, for trace amounts of gases it is impractical to increase the sample size because of the physical limitations of the apparatus and the increased degassing time which would be necessary. Also, when only one of the desired gases is present in trace amounts, quantitative separation by conventional vacuum fusion is almost impossible. Since small analytical mass spectrometers are now commercially available, it was decided to use this instrument in conjunction with conventional vacuum fusion for both qualitative examination and quantitative determinations of the gaseous elements in steel. This technique has already been used with success for the analysis of copper and lanthanum.2"4 APPARATUS A vacuum-fusion unit was first designed and built, Fig. 1. This unit was designed especially for the determination of small amounts of nitrogen and/or oxygen in steel since an acceptable method (vacuum tin-fusion)5 was already in use for the determination of hydrogen in steel. The vacuum system was con- structed of Pyrex glass throughout. Mercury check valves were used in place of stopcocks in the high-vacuum section of the system. Ferromagnetic samples are normally introduced into the vacuum system through a mercury lift. In case of a break in the lift, the mercury is prevented from entering the furnace by a self-locking, mercury safety check valve, Fig. 2. This check valve, developed at our laboratory, is a modified T/S ball-and-socket joint placed in the sample inlet system between the mercury and the furnace. A sudden entry of mercury or air pushes this valve into the closed position, completely blocking the top of the mercury lift. The check valve is held in the closed position by the vacuum of the apparatus. A separate entrance tube also was placed in the system, so that samples which would amalgamate with mercury, or which are nonmagnetic, could be introduced into the furnace. A slightly modified Guldner-Beach furnace is used in this system.8 The optical flat was connected to the system by a ground-glass joint to facilitate cleaning, a quartz delivery tube was substituted for Pyrex, and the crucible was used uncovered. Fusion takes place in a high-purity graphite crucible insulated by — 200-mesh high-purity graphite powder. The crucible set (crucible and funnel) is suspended in a quartz crucible. The furnace envelope and the sample inlet system are exhausted by 2 single-stage, mercury-diffusion pumps in series. The first of these is a high-speed pump, which will work only with a very low backing pressure. This pump is used to exhaust the gases from the furnace as rapidly as possible. The second mercury-diffusion pump is used as a backing pump for the first; the capacity of this pump is much lower. However, it will work efficiently against a back pressure of 3 mm of mercury. To assure positive pumping, a modified Naughton and Uhlig condenser7 is used. With the use of proper valving the second pump is also used as a circulation pump in the catalyst system.

Jan 1, 1959

By H. F. Ramstad, F. D. Richardson

The equilibria (a) SiOz +Hz =SiO +H20 and (b) Si + SiO, = 2Si0 have beet1 studied at temperatures of 1425"to 1600°C ad 1310°to 1485°C respectively. The stattdard free energy changes for the tzrro reactions are given by the equatiotts Combination of the results for both equilibria leads to tiotz removes certain anomalies in existing high-terlzperature data for equilibria involving silica and silicon in iron. In many metallurgical processes and in many laboratory investigations silicon monoxide undoubtedly plays an important role. It is unfortunate therefore that wide differences exist between the results obtained by different investigators1-7 in their studies of such equilibria as In an attempt to put our knowledge of SiO on a surer basis, an exhaustive study has been made of equilibria [I] and [2] at temperatures ranging from 1300" to 1600°C. Reaction [I] was studied by measuring the amounts of silica which could be condensed from streams of Hz or Hz + HzO which had previously been brought into equilibrium with silica at temperatures ranging from 1425" to 1600°C. Reaction [2] was studied by measuring the material that could be condensed from streams of Hz or argon which had been brought into equilibrium with mixtures of silicon and silica at temperatures ranging from 1310" to 1485°C. EXPERIMENTAL Materials. The silicon was "superpure" grade and contained less than 0.1 pct impurities. The silica was prepared from pure mineral quartz; this was crushed and treated with concentrated hydrochloric acid to remove particles of iron, washed with water, and finally dried at 120°C. For the hydrogen + silica reaction, the silica was sized to —20+100 mesh. For the silicon + silica reaction, the two materials were ground to a fine powder in an agate mortar. The hydrogen and argon were commercial oxygen-free gases. The gas streams were controlled with capillary flow meters and the volumes were measured by wet gas meters. After passing through the meters, the gases were partially dried by silica gel. The hydrogen for the HZ + SiOz reaction was then passed through palladised asbestos at 300°C and dried with magnesium perchlorate. The efficiency of oxygen removal was checked throughout the experiments by passing the gas over an electrically heated strip of nichrome, used as an indicator as described by Rathman and de itt.&apos; When mixtures of HZ + Hz0 were required, the partial pressures of water vapor (1.8 to 22 mm) were obtained by passing the hydrogen through oxalic acid dihydrateg&apos; lo held at various controlled temperatures, O.l°C, by means of a water bath. The hydrogen for the Si + Si02 reaction was purified by passing it over a mixture of 3 parts of magnesium to 5 of lime heated to 600°."l1 u The argon for this reaction was passed through titanium powder (-3/16 in. + 100 mesh) heated to 900°C. The nitrogen used to prevent the reaction products escaping from the condenser (see later), was deoxidized by copper or iron at 600°C. All these gases were finally dried with magnesium perchlorate. Furnace, Temperature Contr01, and Measurement A molybdenum resistance furnace was used for both sets of experiments. The reactions were conducted inside a high-grade alumina tube, 36 in. long and 1 in. in diam as indicated in Fig. 1. With this arrangement an even temperature zone (2"C) 4 cm long was satisfactorily obtained. The temperatures were kept constant by means of a proportional controller actuated by a Pt-Pt 13 pct Rh thermocouple. This was placed between the two alumina tubes, so that the temperature at the junction was 1400" to 1450°C. Up to 1485"C, the temperatures were measured with Pt-Pt 13 pct Rh thermocouples. For higher temperatures an optical pyrometer was used, this being sighted (through the glass window 1 in Fig. 1) on the end of the alumina tube, that held the SiOz or Si +SiOz mixture, 10 in Fig. 1. The optical pyrometer was recalibrated whenever a change was made in any part of the apparatus situated in the hot zone. Successive readings with the optical pyrometer were reproducible to within 1"C. Equilibrium Apparatus and Procedure. Hydvogen and Silica Reaction. The apparatus is shown in Fig.

Jan 1, 1962

By Robert E. Green, Robert A. Swanson

Ultrasonic attenuation and stress were measured simultaneously as a function of strain for aluminum single crystals tested in compression. The propagation mode and polarization of the ultrasonic waves were chosen with reference to the theoretical analysis presented in Part I. Good experimental agreement was found with this theory and with earlier experimental work in tensile tests. Support is given to the contention that ultrasonic -attenuation measurements are much more sensitive to the early stages of plastic deformation than are conventional stress -strain measurements. Dislocation meclzanisms are suggested which are compatible with both the present and the earlier experimental observations. A brief historical introduction of previous work concerned with the study of dislocation motion by ultrasonic-attenuation measurements has been given in Part I. The purpose of the present experimental investigation was to make use of the theoretical considerations from Part I in order to gain further knowledge concerning dislocation motions during plastic deformation. Emphasis was placed on the choice of propagation modes and polarization of the waves, such that interactions between these waves and dislocation movement on a specific slip system could be investigated. EXPERIMENTAL PROCEDURE Since the primary concern of this investigation was dislocation damping, other sources of damping were eliminated as much as possible. The test specimens were 0.5-in.-diam single crystals of 99.99+ pct pure aluminum grown from the melt by a modified Bridgman technique. Ultrasonic-attenuation measurements were made at a frequency of 10 megacycles per sec using a Style 56A001 Ultrasonic Attenuation Comparator manufactured by Sperry Products Inc. after a design by Chick, An- derson, and Truell.1 At this frequency the particle vibrations are essentially adiabatic and thermo-elastic damping should be absent. This frequency was selected since it was one of the frequencies used by Hikata et al.2 n conjunction with tensile tests on aluminum crystals, thus allowing direct comparison with this work. The use of quartz-crystal transducers insures that the amplitude of vibration is not sufficient to cause the break away of the dislocation loops from weak pinning points. The quartz-crystal transducers used all possessed a resonance frequency of 10 megacycles per sec and were thin circular discs 0.375 in. in diameter. X-cut crystals were used to generate the longitudinal waves and AC-cut crystals to generate the transverse waves. Aluminum was chosen as the basic material because it is a typical fcc metal whose deformation behavior is well-known and because the most recent work at the time the present research was initiated was that by Hikata et al. who used aluminum. The present tests were run in compression to see if such tests could be satisfactorily run in compression without being severely masked by grip effects.. A second reason was to compare the results in compression with those of the tension experiments of Hikata et at. Finally, shorter specimens could be run in compression with less over-all damping than in tension. All of the aluminum-crystal test specimens used were oriented for plastic deformation by single slip; i.e., they possessed the orientation having a maximum Schmid factor of 0.5. Because of the well-known time dependence 3 of plastic strain at constant stress, the test specimens were subjected to a quasi-static loading. Previous investigations4-&apos; have indicated that attenuation after plastic deformation is also time-dependent, so any continuous loading of the specimen would show that changes in attenuation were also a function of strain rate. By loading the specimen to a given stress level and holding it constant until the recovery process was essentially complete, the time dependence was eliminated. The quartz transducer was permanently bonded to the aluminum crystal using Eastman 910 cement. Excess cement was removed from around the quartz with DMF (dimethyl formamide). Eastman 910 was found to be far superior for bonding, especially with regard to the shear-wave transducer, since it formed a solid bond which readily supports shear-wave propagation. The solid bond formed by the Eastman 910 cement also insured that the quartz

Jan 1, 1964

By R. T. O’Brien, J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and Ni (11) and Co (Ilj concentrations. Results have been discussed in terms of adsorption of Ni (11) and Co (11) cations and hydroxide precipitates. Possible relationships between the experimental results and the formation of lateritic nickel deposits have been discussed. The adsorption of metallic cations to the surface of silicate minerals is of significance in many industrial and natural processes. In an earlier publication,&apos; the adsorption of Fe (111) to the quartz surface, a phenomenon of importance in flotation, was studied qualitatively using microelectrophoresis techniques. This paper reports the extension of this work to an investigation of the adsorption from aqueous solution of Co (11) and Ni (11) to the quartz surface. The adsorption of these metals was of interest for two reasons; firstly, the importance of such an adsorption process in the formation of nickel deposits by the lateritization of nickeliferous rocks, and secondly, the comparison of electrophoresis data for these metals, whose hydroxides precipitate in the pH range 7-8, with similar data for Fe (111) where the hydroxide first precipitates at pH 2.8. The development of laterites is essentially a near-surface geological process involving vertical and, in part, horizontal redistribution of elements derived from rock-forming minerals. This redistribution of elements leads to the formation of layers within the lateritic profile which are enriched in one or more of these elements and, depending on the nature of the original rocks, continued lateritization may give rise to iron ores, bauxites or nickeliferous laterites. The mechanisms discussed in this paper deal with the last mentioned type of deposit although the considered factors are applicable to laterites in general. Nickeliferous laterites are derived from basic and ultrabasic rocks containing ferro-magnesian silicates. These rocks may be partly or wholly converted to serpentinites. Besides their high Mg, Si and Fe contents, they also contain small amounts of Mn, Al, Cr, Ni, Co, Cu and Zn. The nickel content is usually near to 0.2-0.3%, but for economic use this must be increased during lateritization to over 1% and preferably over 2%. The zone of nickel enrichment is usually at some depth within the lateritic profile. Unpublished work by Mr. O&apos;Brien on nickel-bearing laterites in eastern Australia indicated four visually different types of material which were separated from crushed samples under a stereo-microscope. Although chemical analyses indicated that all four types of fragments contained 2-4% nickel and smaller amounts of cobalt, X-ray diffraction and optical studies revealed only quartz, hematite and chromite as well as, in one of the types, a serpentine mineral. No distinct, nickeliferous minerals were detected. Furthermore, it was possible to extract some 60% of the nickel content of the laterites with cold 0.5N hydrochloric acid. It was therefore postulated that much of the contained nickel was present as amorphous, adsorbed material. In considering this fact, as well as the problem of the actual method of transfer and fixation of elements within the lateritic profile, it was further postulated that the transfer of these elements probably took place partly as solutions and partly as colloids and that the fixation of these was caused by adsorption and flocculation. The existence of nickel in solution in water draining from serpentinites has been confirmed by Smurov.2 Although we have no evidence for the transportation of nickel in the colloidal state, it is well accepted that colloids are important in the formation of laterites. Previous work by Mr. Mackenzie&apos; has already indicated that iron may be adsorbed on quartz under conditions which could be expected in a lateritic profile, but no information was available for nickel or cobalt. Although adsorption possibly also takes place on minerals other than quartz, the latter is significant because silica is an important constituent of the silicate parent rocks. During lateritization, it is released to form free quartz and it is likely that it is initially extremely fine-grained. This would provide abundant opportunities for adsorption and it was de-

Jan 1, 1970

By W. D. Forgeng, R. L. Folkman, D. C. Hilty

The solubility of oxygen in molten Fe-Cr alloys has been determined at 1550° , 1600°, and 1650°C for alloys containing up to alloyshasbeenabout 50 pct Cr and found to decrease as chromium increases to 6 pet and then to increase gradually. Phase relations in the Fe-Cr-0 system at steelmaking temperatures have been evaluated and two previously unreported oxides have been identified. OPERATIONS in the melting and refining of chromium steels are dependent to a major degree on the reactions of chromium and iron with oxygen and are primarily directed toward controlling and modifying these reactions to secure maximum advantage in the utilization of chromium. Although fairly effective practices have been developed empirically, understanding of the specific reactions is limited. Moreover, the ability of molten steel to dissolve oxygen that subsequently precipitates as oxide inclusions during solidification is well known, so that clarification of the effect of chromium on the nature and mechanism of formation of these inclusions is desirable. Study of the problem indicated that increased knowledge of the fundamental Fe-Cr-0 system is essential to further technical and economic improvement. Consequently, an investigation of the influence of chromium on the solubility of oxygen in molten iron and of phases and phase relations in the Fe-Cr-0 system was undertaken at the Metals Research Laboratories of the Electro Metallurgical Co. as part of a general program on the effective utilization of chromium in chromium steel production. Experimental Procedure All of the experimental runs made during this investigation were carried out in the rotating crucible induction furnace which has been described in detail in a previous publication.&apos; In review, the principle underlying this furnace is that rotational forces in the crucible cause the molten metal to assume a concave shape in such a manner that the slag is contained in the molten metal cup, thereby minimizing slag/crucible contact and subsequent reaction. Practically all of the heats were melted in commercial-quality magnesia crucibles of the type usually furnished for laboratory induction furnaces. All of the runs were made under an argon atmosphere after the furnace chamber had been degassed. Bath temperatures were controlled by Pt—Pt-10 pct Rh thermocouples. The basic furnace charge consisted of a premelted 12 to 15 lb electrolytic iron slug which had been cast to a shape convenient for fitting into the rotating furnace crucible. A typical analysis of the electrolytic iron slugs is given in Table I. For certain runs, it was desirable to melt down charges containing high initial chromium contents. In these cases the chromium was added to the electrolytic iron during the premelting operations. Chromium was added to the rotating furnace bath in the form of electrolytic chromium of the analysis given in Table 11. In all of the constant temperature runs, the standard procedure was to melt down the electrolytic iron or alloy slug under vacuum, admit argon to slightly greater than atmospheric pressure, and adjust rotational speed to develop a well formed "cup" on the bath surface. The melt was then saturated with oxygen by an addition of ferric oxide and the temperature of the bath adjusted to within +5°C of the desired level. At this point the heat was permitted to come to equilibrium prior to sampling or further addition. This time interval was varied from 15 min to 2 hr but generally was about 20 min. After sampling, the desired chromium addition was made and the bath again equilibrated prior to subsequent sampling. This cycle of addition and sampling continued for the duration of the run which lasted from 4 to 8 hr. At the end of this period, power was shut off and the bath allowed to solidify in the furnace. Quenched metal samples were taken from the equilibrated melts by means of the "Taylor sampler" which has been described by Taylor and Chipman.&apos; Before being submitted to chemical analysis, all samples were carefully examined for surface slag occlusions and cold shuts. Later in the study, each sample was radiographed and examined metal-lographically in cross-section to determine the presence of internal defects. On the basis of these examinations, sound and apparently clean specimens were selected from the Taylor samples for chemical analysis.

Jan 1, 1956

By M. E. Wadswort, A. S. Peck

Infrared data disclose that phenacite reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. The absorption band characteristic of the antisymmetrical C = 0 oleate structure appears at a spectral wavelength of 1623 cm-&apos;. Chemisorption also results in the displacement of OH- and silicate from the mineral surface. Infrared absorbance at 1623 cm-1 is correlated with float-ability at different pH for -60-mesh phenacite particles. Phenacite, Be2SiO4, is an ore mineral often associated with quartz, microcline, and chrysoberyl in pegmatites and mica schist. Experimental phenacite beneficiating processes have been confined principally to the flotation of low grade ores occur-ing in several mountain ranges of Utah and Nevada. The U.S. Bureau of Mines &apos; has recently reported on the separation of phenacite from ore deposits of Mount Wheeler, Nev. Infrared techniques were previously applied by the authors to characterize the role of sodium oleate and oleic acid in the flotation of several non-sulfide minerals.23 A parallel study was projected to the flotation of the orthosilicate mineral phenacite with oleic acid. Infrared spectra provided a &apos;molecular fingerprint&apos; of the mineral surface and permitted identification of the reaction mechanisms. Infrared data were complemented with flotation and chemical tests. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation, for which data are presented in graphical or spectral form, are described in chronological test order. Phenacite crystals from Mt. Antero, Colo., were obtained from Ward&apos;s Co., Monterey, Calif. The crystals were fragmented in a porcelain mortar to -60 mesh and then pretreated with 0.5 molar HC1 for 15 min to remove iron. Then, the mineral particles were washed free of acid with distilled water and dried. Part of the dried material was ground to a fine powder with a Fisher Grinder using an agate mortar and pestle. Next, the powder was placed in a graduated cylinder and mixed with 500 ml of distilled water. The mineral in suspension was decanted from the settled fraction after 5 min, and the colloidal suspension was used for adsorption tests in which a high specific mineral surface area was required for adsorption and infrared analysis. Conditioning was performed in 50 ml glass centrifuge tubes for both infrared and flotation test determinations. Twenty ml of colloidal suspension was used for the infrared adsorption tests. One and a half g of deslimed -60-mesh HCl pretreated phenacite was added to 20 ml of distilled water for flotation conditioning tests. Six mg of oleic acid was used for each infrared adsorption test, and 0.2 mg of oleic acid was used for the flotation conditioning tests. HCl and NaOH were used for pH modification. The pulps were stirred at a speed of about 1500 rpm for 3 min. Then, the solids were separated out and either dried at 50°C or immediately transferred to a float cell. The pH of the residual liquid was determined with a Beckman Zeromatic pH meter. The flotation procedure is described as follows: 1) A 325-1111 glass micro-float cell was filled with distilled water. 2) Conditioned mineral was placed in the cell and the pulp was aerated through the glass fritted bottom at 7 psi pressure. 3) Floated mineral was skimmed from the cell with a glass slide until flotation ceased. (The end point was reached in all tests in less than 2 min.) 4) The flotation products were dried, weighed, and the recovery was calculated. Samples for infrared analysis were made into mulls using either oleic acid or series 13-21 Halocarbon oil obtained from Halocarbon Products Corp., Hacken-sack, N.J. The mulls were placed between two sodium chloride windows. A characteristic phenacite infrared band at 1868 cm-&apos; was used as an internal standard for quantitative determinations in which absorbance at this position was quantified by the baseline-tangent method4 and related to absorbance at 1623 cm-&apos;. The ratio obtained by dividing absorbance at 1623 cm-&apos; by absorbance at 1868 cm-&apos; was defined as an absorbance quotient for use in graphical presentation.

Jan 1, 1968

By R. W. Cahn, C. D. Graham

The rate of growth of a single grain growing into a strained aluminum single crystal, measured by the conventional heat-cool-etch technique, is shown to decrease with time at temperature. The growth rate measured by means of X-rays, with the sample continuously at temperature, is found to be linear. Evidence is presented to show that the decreasing growth rate obtained by the conventional technique is due to abnormal recovery in the strained grain, and that the recovery in turn results from the heating and cooling cycles, rather than from the effects of etching. The experimental apparatus is described in an appendix. FREQUENTLY, the rate of grain boundary motion during recrystallization is determined by heating a sample to a known temperature for a given time, cooling to room temperature, and etching to reveal the boundary position. The cycle of operations is repeated as many times as necessary to establish the rate of boundary motion. Although this heat-cool-etch technique has been used by a number of workers over a period of many years,&apos;-!&apos; other investigators have encountered difficulty with the method."&apos;. " They have attributed the erratic results to the effects of repeated heating and cooling, or of etching, or both, and have adopted an alternative experimental procedure in which a number of identical samples are employed, each sample being cooled and etched only once. This alternative method ove1.comes some difficulties, but introduces others. In particular, the incubation periods of the observed grains are unknown: any effect of crystal orientation on growth rate cannot be determined easily. A preferable method would be to measure the motion of a recrystallizing grain boundary with the sample at temperature without etching," but such measurements have in the past been restricted to nonmetals. This paper describes the construction and operation of a device, the goniometer furnace, with which the position of a moving grain boundary between a recrystallizing grain and the strained single crystal into which it grows can be measured by means of X-rays, with the sample maintained continuously at temperature. Goniometer Furnace The operating principle of the goniometer furnace is shown in Fig. 1. The sample, in the form of a bicrystal strip, is surrounded by a furnace, not shown in the sketch, and can be rotated about the two axes A and B which intersect at the point where the X-ray beam strikes the strip. The strip is oriented so that one of the two grains gives a strong Bragg reflection, which is detected by a suitably placed Geiger-Miiller counter coupled to a counting-rate meter When the strip is moved parallel to its own length in the furnace, arrow C, so that the X-ray beam strikes the second grain, there is in general no strong reflection. By noting the position of the strip at which the drop in Geiger counter reading occurs, it is possible to determine the position of the boundary. Measuring the change in boundary position with time at temperature gives the rate of growth of the recrystallizing grain. Details of the construction and operation of the goniometer furnace are given in the Appendix. Measurements showed that the temperature in the furnace was uniform within ±10°C over its working length of about 28 cm. The temperature at the measuring position, i.e., at the point where the X-ray beam struck the sample, was estimated to be constant within ±2oC. Using the goniometer furnace, the position of a stationary boundary could be measured with a reproducibility of ±0.3 mm. At elevated temperatures, 500" to 625"C, with the boundary in motion and the X-ray reflection less sharp, the estimated accuracy of each measured boundary position dropped to about ±1 mm. Experimental Results The test pieces were single crystals of 99.6 pet A1 —principal impurities 0.19 pet Fe and 0.12 pet Si— 1 mm by 1 cm in cross section and 6 to 10 cm in length, grown by the strain-anneal method. This relatively low purity material was used because of the difficulty encountered in producing strain-anneal single crystals of very high purity—99.996 pet—

Jan 1, 1957

By J. B. Cohen, B. W. Howlett, M. B. Bever

The partial molar heats of solution at infinite dilution in tin of aluminum at 300° and 350°C and of gallium, indium, and thallium at 240°, 300°, and 350°C have been measured by tin solution calori-metry. Aluminum, gallium, and thallium are endo-thermic on solution; indium is exothermic. Any temperature dependence of the heats of solution lies within the experimental scatter. Over the dilute ranges investigated, only aluminum has a measurable change in its heat of solution with composition. HEATS of solution of one element in another reflect the interaction between them. The investigation of partial molar heats of solution in dilute alloys is of particular interest as the properties of the solvent are altered to only a limited extent by the presence of the solute and also as the interaction between solute atoms is small. When the heats of solution of a related series of elements in a solvent are known, a systematic comparison may be made. In the investigation reported here, the partial molar heats of solution of the Group III elements aluminum, gallium, indium, and thallium in dilute solution in tin were measured. This work follows an investigation of the heats of solution in tin of the Group IB elements.&apos; EXPERIMENTAL PROCEDURES Materials. Samples of gallium, indium, and thallium were obtained from Johnson, Mathey and Co., Ltd. Indium and thallium were supplied as wire, 1.6 mm in diam; gallium was in the form of irregular pieces. The supplier reported the following minimum purities: gallium—99.95 pct; indium—99.99 pct; thallium—99.99 pct. The aluminum, obtained from Alcoa Research Laboratories, was reported to be 99.995 pct pure. The tin was supplied by Baker and Co., Inc.; the reported analysis indicated a tin content of at least 99.96 pct with lead as principal impurity. Calorimeter. this description will cover only the essential features of the calorimeter with special attention to modifications made since an earlier description was published.&apos; A Dewar flask containing the tin bath was held in a constant-temperature bath of a near-eutectic mixture of lithium, sodium, and potassium nitrates. This bath, which was stirred vigorously, was heated by a primary resistance winding in the container wall and by a secondary winding immersed in the salt. The voltage supplied to both windings was stabilized. The temperature of the salt bath was controlled by means of a platinum resistance thermometer in one arm of a Wheatstone bridge. The light from a mirror galvanometer in the bridge circuit fell on a photocell which controlled the current in a saturable reactor in series with the secondary winding. In this manner, the temperature of the salt bath was controlled to ±0.003°C and that of the tin bath to at least ±0.002°C. Each of these temperatures was measured by two iron-constantan thermocouples in series, coiled in a helix to minimize heat loss and immersed in the salt and tin baths in protective sheaths. The temperature of the laboratory was kept constant to ± 1°C during a run. Specimens were dropped into the tin bath from an addition arm held at O°C which was part of the cal-orimetric system. The system was evacuated to about 0.02 1 to minimize oxidation and to reduce transfer of heat. The bath was stirred by a glass stirrer introduced through a double Wilson seal. The samples were scraped clean before weighing, which was carried out as rapidly as possible. Each sample was immediately placed in the evacuated addition arm to minimize contamination. These precautions were especially necessary with aluminum. After the runs with gallium and thallium at all temperatures and with indium at 240° and 350°C (Series I) were completed and before the runs with indium at 300°C and aluminum at 300° and 350°C (Series 11) were begun the following changes were made. The shape of the Dewar flask was changed so as to result in a lower surface to volume ratio of the bath and at the same time the amount of tin was reduced from 500 to 400 g. The paddle type stirrer was replaced by a helical screw and the rate of stirring was increased to about 150 to 200 rpm.

Jan 1, 1962

By D. M. Schuster, E. Scala

The elastic effects occurring in the matrix of a composite reinforced by discontinuous fibers were studied by means of photoelastic techniques. A hirefringent plastic was employed as the matrix material with high-strength a Al2O3 whiskers as the reinforcing fibers. It was found that for whiskers aligned parallel to the tensile load direction: (I) Matrix reinforcement occurred along the length of the whisker to within about 5 diameters of the whisker tip for a length to diameter ratio, L/D, of 40. (2) Significant stress concentrations were created in regions immediately surrounding the tips; the fine as-formed tapered ends exhibited the minimum stress concentration whereas the square-ended whisker produced relatively high values, K r 2.5 for L/D = 40. (3) The axial and radial stress distributions could he determined quantitatively; the stress distribution at the whisker-matrix interface was in general agreement with theoretical calculations. (4) The highest source of stress concentration occurred at points of fracture in whiskers which had ruptured after incorporation into the composite. Whiskers aligned perpendicular to the load direction neither reinforced nor caused appreciahle stress concentrations in the matrix. ThE properties of composites have generally been formulated empirically on the basis of macroscopic tests. There are still many questions concerning the mechanical and chemical interactions occurring at the interface between the reinforcing fiber and its matrix. Continuously reinforced plastics and dispersion-hardened metals represent the two extremes of composite reinforcement. Whether artificially produced or formed in situ, the whisker composite falls between these two extremes and is an example of discontinuous fiber reinforcement. The effect of fiber shape, size, surface condition, and end configuration on the stress distribution in the matrix is important since the presence of stress concentrations, especially in any high-strength, thin-wall structure, could become the cause of catastrophic failure. DOW,&apos; in his theoretical discussion of discontinuous fiber reinforcement, has pointed out that appreciable stress concentrations occur at the tips or ends of the reinforcing fibers. It is the purpose of this study to examine directly, by means of the photoelastic technique, the stresses which occur in the vicinity of a discontinuity or whisker tip and to measure qualitatively and quantitatively the effects of whisker geometry when embedded in a birefringent matrix material. The use of sapphire (a A1,O3) whiskers was decided upon as the reinforcing agent because of their high elastic modulus (E- 60 X 106 psi) and in some cases strengths in excess of one and a half million psi. Sapphire whiskers are of further practical interest since they retain large fractions of their strength up to temperatures approaching the melting point (3720oF).2 The whiskers were grown, by the vapor-phase reaction commonly employed,3 as part of this study to insure a physically uniform supply. Tensile and bend tests were performed to verify that the whiskers were of the expected ultra-high strength. The high-strength whiskers can be identified and selected from the combustion boats by surface perfection, shape, and size; otherwise, strength values can vary by a factor of ten or more. Macroscopic defects are quite common on the surface of large bladed whiskers and the principal experiments were conducted with hexagonal whiskers of about 0.002 in. diameter and lengths ranging from 0.1 to 0.4 in. Upon completion of these two phases of the experiment, several birefringent resins were evaluated. A plastic, developed by Zandman,4 which is supplied by the Budd Co., was found most suitable and was used as the matrix material for the whisker composite throughout the study. It has a sensitivity of 60.5 lb per in. order, calibrated in tension and cures without introducing residual stresses. Young&apos;s modulus for this matrix material is 430,000 psi in the fully cured condition. Since good wetting and bonding between the sapphire and the matrix material is essential to the interpretation of the results, a wettability test was performed. The contact angle was measured to be 168 deg where perfect wetting is defined as 180 deg; therefore, the Budd Plastic wets the sapphire

Jan 1, 1964

By A. W. Sommer, H. H. Kellogg

It is shown that SO3-O2 mixtures react with sphalerite at an appreciable rate ill the temperature range of 361° to 527°C to fornz ZnSO4. The rate of reaction follows a parabolle lax. Oxygen, or O2-SO2 mixtures, have a negligible effect on sphalcrite in the same temperatuee range. PRACTICAL roasting of sphalerite is usually performed at 800°C or higher. The calcine is composed of zinc oxide unless the roaster atmosphere contains relatively large amounts of SO2 and the temperature is held to 800oC or lower, in which case zinc sul-fate may also form. Ong, Wadsworth, and assell&apos; have made a careful kinetic study of sphalerite oxidation under these "normal conditions" and have concluded that the rate of the reaction is controlled by the decomposition of an activated complex adsorbed on the sphalerite surface. They found the rate of oxidation to be small at 700°C. Extrapolation of their data to 400°C would indicate an almost negligible rate at this temperature. In our work sphalerite was reacted with air, mixtures of SO2, O2, and N2, and mixtures of SO3, O2, and N2 in the temperature range 361o to 527OC. Negligible rates of oxidation were found, except for the gas mixtures containing SOs. With this latter gas, the oxidation of finely divided sphalerite was fairly rapid and zinc sulfate was the product. Based on the limited evidence available, the rate of sphalerite oxidation by SO3 is postulated to be controlled by gaseous diffusion through pores or cracks in the zinc-sulfate coating. This evidence for the direct reaction of sphalerite and SO, at low temperature may prove of importance to the understanding of zinc-sulfate formation in the dust-collecting equipment usually associated with zinc roasters. The roaster gas carries off fine dust, much of which may be unreacted sphalerite. The temperature in dust-collecting equipment drops from the roaster temperature (about 800°C) through the range of temperature we studied, to ambient temperature. Such dusts are known to contain far larger amounts of zinc sulfate than the primary calcine. It has been assumed in the past that this sulfate is formed by reaction of ZnO dust with SO3 (or SO, plus 0,) in the partly cooled gases. Our work shows that an alternative possibility exists—the direct reaction of SO3 with ZnS dust. EXPERIMENTAL Reaction rates for sphalerite at 350° to 600°C are relatively small so that it was necessary to use finely divided material with a relatively large surface area in order to obtain measureable amounts of reaction. In the preliminary experiments, pure mineral sphalerite, ground to pass a 325-mesh sieve, and chemically precipitated ZnS (in the form of an impalpable powder) were used. In the quantitative rate experiments the ground mineral sphalerite was processed in an Infrasizer to obtain a product with particle size between 9 and 18 µ. The analysis of this material was 66.7 pct Zn, 0.09 pct Fe, and 32.7 pct S (theoretical sphalerite is 67.1 pct Zn, 32.9 pct S). The sized powder was carefully mixed and divided into l-g samples. The apparatus used for the quantitative rate measurements is shown in Fig. 1. For the preliminary experiments the following change was made: The external catalyst furnace (B, C)* was not used. *Letters refer to Fig._______1 .___- Rather, when catalysis of the SO2 + O2 reaction was desired, the glass beads in basket M were replaced by vanadium-oxide pellets. Procedure—A l-g sample of ZnS was placed on a shallow stainless-steel tray, I, and spread evenly to a depth of about 1mm. The tray was placed in the reaction assembly and the assembly inserted in the cold furnace. The furnace tube was flushed with dry argon and then heated to the desired reaction temperature. The temperature was controlled to ±0.5oC. Gas mixtures (O2 + N2 or O2 + SO2) were prepared from tank gases by means of a mixing device identical to that employed by Darken and Gurry.2 The total flow rate of gas was 205 ml per min to point A of Fig. 1. The accuracy of the individual and

Jan 1, 1960

By H. S. Thomsen, W. C. Duesterhoeft, R. E. Hartline

The attenuation and phase shift which formations produce in the electromagnetic field of an induction-type electrical well-logging instrument are great enough to substantially affect the response of the tool to formation conductivity under normal logging conditions. The application of the general equations for the propagation of an electromagnetic field in a conductive medium to the transmitter-receiver coil pair of an induction-logging-tool coil system gives an expression for the response which properly takes the propagation effects into account. A comparison of a calculation of this type with the response computed from the commonly used geometric factor concept, which does not include the propagation effect, leads to a factor Go representing the ratio of the responses computed by the two methods. The value of Go decreases not only with increasing formation conductivity, but also with increasing transmitter-to-detector coil spacing. For a single coil pair with a 40-in. spacing, the value of Go is 0.972 in a 20-millimho/m formation. The value is reduced to 0.915 and 0.812 for conductivities of 200 and 1,000 millimhos/m. As a result, the basic signal generated by the induction-logging coil system is not linearly related to formation conductivity as expected from the geometric factor concept. A uniform conductivity scale can be obtained only by adding a suitable nonlinear element to the recording system. The addition of auxiliary coils, having spacings less than the main-coil span, to achieve focusing results in an even greater departure of the basic signal from linearity with conductivity. The solution of the field equations near the interface between two formations of different conductivity gives the curve shape on an induction logging tool in crossing the interface. The addition of auxiliary coils to achieve focusing can add anomalous character to the curve shape in crossing the interface, which might be mistaken for lithological detail. Preliminary calculations which include the propagation effects in the determination of the conductivity correction for thin beds lead to correction factors which are substantially smaller than those obtained from geometric factor considerations. It is apparent that thin-bed corrections derived from geometric factor calculations are of doubtful validity. INTRODUCTION Although the electromagnetic induction type of electrical well log has been used for a number of years and has gained general acceptance in quantitative well-log interpretation, no technically complete investigation of the mechanism and of its operation has been published. The studies which have been presented are based upon the premise that neither the shape nor the intensity of the induction field of the logging tool is in any way affected by the electrical characteristics of the formation. From the inception of induction logging it has been recognized that under some formation conditions the performance of the instrument could be expected to be substantially different from that predicted by the simplified analysis. This anomalous performance has been called "skin effect" since it is the result of the same phenomenon which causes high-frequency alternating currents to flow only near the surface of metallic conductors. In the range of conductivities encountered in the sediments, the formation actually does not exhibit the sharply defined conducting "skin" shown by metals. The gradual modification of the distribution of the currents in the formation, produced by the induction field of the logging tool, is the direct result of phenomena associated with the propagation of the electromagnetic field through the formation. Therefore, it can be much more appropriately described as the "propagation effect". One purpose of this paper is to review the results of a solution of the equations for the performance of a single transmitter-receiver coil pair induction-logging system which takes into account the propagation effect, showing the manner in which the tool performance established by this analysis differs from that derived from the less comprehensive analyses currently in use. PRINCIPLE OF OPERATION OF THE INDUCTION LOGGING INSTRUMENT The high-frequency alternating current which is maintained at a constant value in the transmitter coil

By D. H. Yardley

GEOCHEMICAL investigation of trace elements in surface materials was begun near Ely, Minn., in 1953 along the basal contact of Duluth gabbro with Giants Range granite (Fig. 1). This article presents data on the distribution of copper and nickel in till and in stream sediments in the area and proposes an explanation for the types of distribution found. The Duluth gabbro, one of the world&apos;s largest basic intrusives, intrudes rocks which range in age from Keewatin to middle Keweenawan. Within the test area the gabbro is in contact with granite except for short sections where it is in contact with remnants of iron formation. Sulfide mineralization occurs within the gabbro, near and parallel to the basal contact for a distance of several miles. Schwartz and Davidson&apos; have described the geologic setting of the mineralization. The sulfides, believed to be syngenetic, include chalcopyrite, cubanite, pentlandite, pyrrhotite, and minor amounts of bornite. They occur disseminated in the silicates and as small interstitial masses. The ratio of copper to nickel is about 3.8:1, based on 66 chemical analyses of rock samples from various outcrops (Ref. 1, p. 702, and Ref. 2). Test Procedures: With specified exceptions, all nickel and copper tests were made by the chromo-graph method,:&apos; which measures the intensity of a colored spot formed by a reaction between the metal being determined and special reagent paper. The intensity is then compared to the intensity of spots prepared from samples of known metal content. Details of the test procedure are outlined in another article (Ref. 4, pp. 77,78). All soil samples tested in this investigation to date have been weighed on an analytical balance. However, a volumetric scoop designed to provide about 0.1 g of soil adds to the speed and ease of testing and has been found to give satisfactory results (Ref. 5, p. 531, and Ref. 19). The size of the samples used for the tests was 0.1 g. Whenever such small samples are used there is some question as to whether they are representative of the several grams in the field sample. Many repeat tests of the samples used in this investigation demonstrated that results can be reproduced within the limits of accuracy of the method without formal mixing beyond that inherent in screening the soil fractions. Furthermore, the 0.1 g is probably as representative of the field sample as the field sample is of its area of influence. Hawkes and Lakin (Ref. 6, p. 291), who considered the general problem, compared ground and quartered bulk samples of 500 g with 5-g grab samples. They concluded that "there is no significant loss in accuracy of data by substituting grab samples for bulk samples." The term soil implies somewhat different things to the geologist, engineer, and soil scientist.&apos; For convenience the term as used in this article refers to unconsolidated material (the mantle) overlying bed rock. Sampling Procedure: Samples were taken at 100-ft intervals along north-south traverse lines across the gabbro-granite contact. The soil (till) samples were taken at an average depth of 1 ft, which was below the high-humus surface layer and into clean till. Samples taken at 1-ft intervals down to ledge showed as high a metal content at 1 ft below the air-surface as at greater depths and in two instances were slightly higher. The till at 1-ft depth did not appear to differ from material at greater depths. Total depth to bedrock has been tested at only a few points and where measured varied from 1 to 10 ft. Aerial Distribution Contours and Profiles: Plotting of copper, nickel, and cobalt content in contour form (Fig. 2) shows that anomalous amounts of these metal ions occur in till over and closely adjacent to mineralized areas of the gabbro. Contouring nickel content alone, or the copper content, outlines the same target area. Contours of the copper content provide a more distinct anomaly than nickel because of the higher copper concentration. The traverses are rather widely spread for interpolation; however, drilling has confirmed the target area essentially as shown.

Jan 1, 1959

By J. K. Elliott, P. H. Kelly

Many engineering functions such as surface metering work and laboratory compressibility check points involve the use of liquid densities of light hydrocarbon mixtures at various pressures and temperatures. However, at the present time, no simple reliable method exists for determining density variation, particularly if the composition of the liquid is unknown. Consequently, a study was undertaken to develop and present a simple and accurate method of predicting density variation of a light hydrocarbon liquid with pressure and temperature, knowing only the density of the liquid at some condition. The experimental liquid compressibility data from API Project 37 by Sage and Lacey&apos; have been considered to be accurate within 0.5 per cent and cover a wide range of pressure (14.7 to 10,000 psia), temperature (100" to 400°F) and molecular weight (up to 150). From these data, a set of liquid density curves, which relate density to pressure, temperature and molecular weight, was developed. These curves make it possible to predict density variation with pressure and temperature. Compared to extensive laboratory compressibility data on a complex, light hydrocarbon liquid, the use of the liquid density curves resulted in an average error of less than 0.5 per cent. Based on the results of this analysis, it is concluded that the set of liquid density curves developed from the data of Sage and Lacey provides an accurate and simple method for predicting the density variation of light hydrocarbon liquids when the density at some condition is known. These curves should be very helpful in many engineering calculations, particularly in the surface metering of light hydrocarbon liquids. INTRODUCTION Many situations arise in field and engineering laboratory work, such as reservoir engineering studies, check of experimentally determined laboratory data and orifice flow-meter formulas, where liquid density factors at various pressure-temperature conditions are required. Also, the need for accurate light hydrocarbon liquid information has become more important with the advent of miscible-type displacements for secondary recovery purposes in oilfield operations. Several reliable methods are available1 - "or determining the density of liquid hydrocarbons if the composition of the liquid is known. However, there is a definite lack of methods for accurately determining the variation of density when the composition of the liquid is unknown. The purpose of this study is to review the various methods for determining hydrocarbon liquid densities and to develop a simple and reliable method of determining variation in density of light hydrocarbon liquids with pressure and temperature when the compositio~n of the liquid is unknown. METHODS FOR DETERMINING DENSITY OF LIQUIDS OF KNOWN COMPOSITION Sage, Lacey and Hicks&apos; have proposed a method to predict the density of light liquid hydrocarbons by using partial molal volumes. Data are available on experimentally developed partial liquid volumes of hydrocarbons over a rather limited range of temperature, pressure and composition. The partial mold volume method has proved satisfactory for determining the density of some hydrocarbon liquids when the composition is known. Within the range covered in the Sage, Lacey and Hicks1 data, the results agree within about 3 per cent of the experimental values. Hanson mentions the limitation of this method to a composition range of approximately 10 per cent by weight of methane, which will not allow this correction to cover most low molecular weight-light hydrocarbon liquids. Standing and Katz2 studied data on light hydrocarbon-liquid systems containing methane and ethane at high temperature and pressure and have presented a method for determining liquid densities, assuming additive volumes for all components less volatile than ethane and using apparent densities for methane and ethane. The compressibility and thermal-expansion curves used by Standing are based on assumptions that compressibility of a hydrocarbon liquid at temperatures below 300°F is a function of the liquid density at 60°F and that thermal expansion of the liquid is affected little by pressure. The information required to use this technique with an example problem is furnished by Standing.&apos; Hanson eports an average error of - 0.5 per cent using the method of apparent densities in calculating liquid densities of several volatile hydrocarbon mixtures. However, as implied, the apparent density method is not applicable for liquid density calculations when the composition of the liquid is unknown. Watson- as presented a method

By Peter Soo

Pvestrained Ferrovac E iron has been neutron-irradiated at approximately 90°C to an integrated flux of 1020 nut (E > 0.82 mev]. The irradiation was found to produce an incveased temperature dependence of the flow stress in addition to a greatly increased athemal stress. Measurements of the flow stress and stress relaxation, from which the activation volume and activation energy for slip were deduced, show that neutron irradiation changes the rate -controlling slip process to one based on dislocation interactions with tetragonal distortions which are Produced around submicroscopic interstitial loops in the lattice. The study indicates that without prestraining prior to irradiation the chances of detecting a change in the rate -controlling slip process are greatly reduced because in the initial stages of slip a substantial fraction of the radiation defects are swept out of the slip plane by gliding dislocations. Thus, activation parameters which are subsequently measured are representative of a greatly reduced defect density and would not differ appreciably from those for unirradi-ated material. The large increase in the athermal component of the flow stress is probably connected with the presence of depleted zones in the lattice which are introduced by irradiation. ALTHOUGH fast neutron-irradiation has not been observed to markedly alter the activation parameters for slip in bcc metals,&apos; small but significant changes do occur. Most experimenters agree that irradiation predominantly increases the athermal component of the yield stress.&apos;-= In addition to this, Laidler and smidt7 have shown that in iron irradiated to 5 X 10" nvt and molybdenum irradiated to 10" nvt, changes occur in the activation volumes for slip. A similar conclusion has been reached by Milasin and Malkin8 for irradiated iron. Work by Ohr et a1.5 shows that for Ferrovac E iron, irradiated to 1.2 X 1016 nvt, small increases in the activation energy for slip also occur. So far these changes in the activation parameters have not been explained on a firm theoretical basis. One important factor which would minimize the chances of detecting a change in the slip mechanism upon irradiation is the presence of "channeling" which has been observed in molybdenum,9 niobium,10 and iron.11These channels are formed by gliding dislocations which sweep irradiation defects out of the active slip planes and thereby create zones in which continued dislocation motion is encouraged. The activation parameters for the dislocations gliding in the defect-free channels would, therefore, be similar to those for unirradiated iron and a change in the rate-controlling slip process would be difficult to detect. In the present work, an attempt has been made to reduce the effect of uneven deformation on the measured activation parameters for slip in neutron-irradiated Ferrovac E iron polycrystals, so that a more realistic assessment of the effects of neutron-irradiation could be made. Primarily, the experiments involve the irradiation of specimens which had been prestrained to 9 pct elongation at room temperature prior to insertion into the reactor. It was hoped that the introduction of a large number of evenly distributed dislocations would substantially decrease any channeling effect which might otherwise occur. MATERIAL AND EXPERIMENTAL PROCEDURE The starting material was vacuum-melted Ferrovac E iron, an analysis of which is given in Table I. The standard tensile specimen had a gage length of 1.125 in., a cross-sectional diameter of 0.120 in., and a re-crystallized grain size of 1.2 x 10-3 in. All tensile tests were conducted on a floor model "Instron" tensile machine at a strain rate of 3 x 10-4 per sec. The irradiation of the prestrained specimens was performed in the Brookhaven High Flux Beam Reactor to an integrated flux of 1020 nvt (E > 0.82 mev) at a temperature of about 90°C. All specimens were excap-sulated in high-purity aluminum sheaths which were lightly swaged around the samples to ensure good thermal contact. Subsequent measurements on the irradiated specimens showed that within experimental accuracy the swaging had not deformed them. EXPERIMENTAL RESULTS Fig. 1 shows the flow stresses for a series of unirradiated control samples. In order to produce a comparable dislocation substructure throughout the test sm range, all specimens were prestrained

Jan 1, 1970

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid-fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made. Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system. Specular hematite was crushed and then ground dry in a laboratory porcelain mill, with flint pebbles, to pass a 200-mesh screen. The ground product was sized in a Haultain infrasizer, and one of the granular sizes (cone No. 3) was used in all adsorption tests. A hand magnet was used to remove magnetite and abraded iron. Quartz was removed in a Frantz isodynamic magnetic separator. The purified hematite was leached in aqua regia, washed with distilled water until the washings appeared free of electrolyte by conductance measurement, dried in a low-temperature oven, and stored in a pyrex container. The specific surface of the closely sized hematite was determined by the krypton gas adsorption method.&apos; Three measurements gave an average value of 1350 sq cm per g. Chemical analysis showed Fe -69.37 pct, insol = 0.72 pct. The quartz used in the flotation tests had been prepared by Chang" for an earlier investigation. Demineralized distilled water was used for all test solutions. Dissolved salt content was of the order of 0.03 ppm, expressed in terms of sodium chloride, as estimated from conductance measurements. Dodecylammonium acetate was obtained from Armour & CO. in two forms, the unmarked compound and a preparation marked by carbon 14 in the hydrocarbon chain of the aminium ion. Specific activity of the active salt was 0.134 millicurie per g. The important physico-chemical constants for the primary amine salt have been reviewed by de Bruyn. The calculated effect of hydrolysis of amine salt on pH of aqueous solutions and the effect of pH on the distribution ratio of the alkylammonium ion to free amine are of particular interest. All other chemicals used in this investigation were of analytical reagent grade. A column method&apos; was used for adsorption work. Attainment of equilibrium distribution in the adsorption column depends on the solid-solution contact time, hence upon the volume of solution passed. It was assumed that contact time required for equilibrium would be a maximum for the lowest reagent concentrations. On this premise it was demonstrated experimentally that the passage of 500 ml of solution through the mineral bed was adequate. An aliquot (1 to 5 cc) of the solution to be analyzed was transferred to a small pyrex cup and allowed to evaporate to dryness at room temperature; 4 or 5 mg of unmarked amine acetate were added to the dried sample and the cup and its contents were transferred to the combustion system for analysis. Evaporation at room temperature must be emphasized, as even slightly elevated temperatures result in loss of reagent. A laboratory model G Beckman pH meter equipped with a glass electrode was used to measure pH of amine acetate solutions. The technique of internal gas counting of radioactive carbon dioxide in a Geiger-Muller counter was used. Developed originally by Brown and Miller,- his method was adapted to the analysis of carbon-14 marked flotation reagents by Chang, de Bruyn, and Bloecher. nalytica1 method and procedures have been described in detail by Bloecher.&apos; Contact angles were measured by the captive-bubble technique." The mineral specimens were carefully selected to avoid cracks and inclusions of other minerals. All specimens were mounted in plastic and polished to produce a smooth surface. The final polishing and contact-angle measuring

Jan 1, 1955

By W. A. Tiller

The conventional techniques1 for determining the liquidus and solidus surfaces of an alloy system containing more than two components are extremely tedious to use and do not provide a complete picture of the equilibrium relations between solid and liquid alloys. These techniques are unable to yield "tie-line" information concerning solid and liquid phase equilibrium, a very important parameter in the solidification description of the liquid alloy and a very necessary parameter in the preparation of "zone-levelled" alloy crystals. The tie-line in a polycomponent system is analogous to the partition coefficient, k, in a binary system, it gives the composition of the solid, Cs, in equilibrium with a liquid of composition CL. That is, CS = kCL, where CL = [CO, c1,...Cn] denotes the concentrations of the n + 1 constituents, and k = [ko, kb ,...kon] denotes the gross partition coefficient for the elements between the two phases; thus, k is the tie-line in this system. To provide complete information concerning the two-phase equilibrium in a polycomponent system it is necessary to know both the liquidus surface and the gross partition coefficient. From these two the solidus surface is obtainable. The conventional techniques are unable to provide this information in other than a binary system so we must look elsewhere. In recent years considerable insight has been gained into the correct description of the liquid-solid transformation, 2,3 and controlled solidification experiments may now be designed to both facilitate and enhance equilibrium diagram studies. In the present paper consideration is given to two methods for obtaining the liquidus surface and the tie-lines in polycomponent systems. The methods to be described below deal with the solidification of an n + 1 constituent liquid alloy of initial composition [co, Co ,...Con], where the superscripts refer to the elements present and the Oth element is considered as the solvent in which the n solutes are dissolved. The general assumptions made in the treatment are the following: (i) the solid and the liquid at their interface are in equilibrium during the growth of the solid phase, (ii) there is no diffusion in the solid phase, and (iii) the liquid phase is completely mixed and is therefore homogeneous in concentration. METHOD I In this section a general experimental method will be described which, in principle, is capable of giving an exact description of the liquidus surface and tie-lines. Consider the unidirectional solidification of the liquid alloy specimens L cm in length (freezing either horizontally or vertically). Allow the sample to be frozen very slowly from one end, as indicated in Fig. 1, with complete mixing in the liquid, and then analyze the solid bar to determine its chemical constitution as a function of position, x, along the bar. Let Fig. 2 represent a possible distribution of the ith constituent along the bar. At the point x&apos; the concentration of the ith constituent is C1/5(x&apos;), and the average concentration of the rest of the bar between x&apos; and L is given by C:(X&apos; - L) where [ A(x) c1s(x)dx c1/s(x&apos;-L) = f A(x) dx x * and A(X) is the cross-sectional area at x. In a similar manner. all the Cf(x&apos; - L) may be determined. Thus, the gross artition coefficient k for liquid of composition [Cs(x - L),...Cs(X&apos; - L)] is given by -ko= CUs&apos;)/Cos(x&apos; - L)" k0 = csn{x&apos;)/cs(x&apos;- L) During the freezing of a charge of length L, the liquid composition may vary over a wide segment of the phase diagram and the gross partition coefficient over this segment of the phase diagram may be determined from one, bar. Fig. 3 illustrates the magnitude of Cs(g)/C,&apos; as a function of the fraction g of the bar which has Solidified.2 We can see that the concentration in the bar will vary over a range of about 15 wt pct for C,&apos; = 10 wt pct and k0 = 0.5. It appears that 4 or 5 specimens would be adequate to study a simple binary eutectic phase diagram.

Jan 1, 1960