Search Documents

By B. M. Loring, I. R. Krame, F. M. Walters

NO observations on the mechanical properties of man-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,' or whether the lack of ductility observed was due to impurities in the alloys that he studied. Experimental Methods The alloys were melted in a roo-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb, ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon was added as ferrosilicon. The alloys forged without difficulty and were given a 9' per Published by permission of the Navy Department. Manuscript received at the office of the Institute June 28. 1941. Issued as T.P. 1369 in Metals Technology. September 1941. * Division of Physical Metallfirgy Naval Roscarch Laboratory. Anacostia Station Washington. D. C. 1 References are at the end of the paper. 4 cent reduction to ¾-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for 224 hr. at r150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for I hr. at 540°C. (Iooo°F.) and air-cooled. The tensils specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were v-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1942

By B. M. Loring, I. R. Krame, F. M. Walters

NO observations on the mechanical properties of man-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,' or whether the lack of ductility observed was due to impurities in the alloys that he studied. Experimental Methods The alloys were melted in a roo-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb, ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon was added as ferrosilicon. The alloys forged without difficulty and were given a 9' per Published by permission of the Navy Department. Manuscript received at the office of the Institute June 28. 1941. Issued as T.P. 1369 in Metals Technology. September 1941. * Division of Physical Metallfirgy Naval Roscarch Laboratory. Anacostia Station Washington. D. C. 1 References are at the end of the paper. 4 cent reduction to ¾-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for 224 hr. at r150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for I hr. at 540°C. (Iooo°F.) and air-cooled. The tensils specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were v-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1942

By Peter G. Groer

Several methods1-3 are being used to determine the WL and individual Rn-daughter concentrations in uranium mine atmospheres. The best of these methods is the one given in Ref. 3. According to this method, the WL and the Rn-daughter concentrations are determined from the total a-counts observed during three consecutive time intervals. Its only disadvantage lies in the fact that rather involved calculations are necessary to convert the observed counts into WL or pCi/l (picocuries per liter). There are, however, counting intervals that give simple weighting coefficients for the observed counts. This fact makes it possible to convert from a-counts to WL or pCi/l with the aid of a graph. After some trial runs on a computer the following equations emerged as the basis for the most practical procedure: [ ] NA, N.., and & stand for the number of RaA, RaB, and RaC atoms per liter of air. C(t1,t2) denotes the counts observed from time t. to time t2 (in minutes) after the end of the 5-min sampling period. E is the detector efficiency and V is the flow rate in liters per minute. With an accuracy loss of less than -5% one finds from [Eq. 1] by adding the corresponding terms: If the WL would have been calculated according to [Eq. 2] instead of using the graph, the result would have been 0.31. Since the values used for C's under [Eq. 3] represent the exact number of counts from a Rn-daughter mixture in equilibrium with 100/3 pCi of Rn the exact WL of this mixture can be calculated easily. The exact value is: [ ] This shows that the method is quite accurate for the 0.3 WL domain. The precision of the method excluding errors made in reading the graph can be estimated with the help of the following formula: [ ]

Jan 1, 1974

By M. B. Bever, A. K. Jena

In the investigation reported here, calorimetric measurements have been made to determine the heat of formation of the compound AuSb2 and the partial gram-atomic enthalpies of antimony and gold in dilute solution in liquid tin and their enthalpy interaction coefficients. In order to interpret the behavior of antimony and gold in dilute solution in tin, nonzero values are assigned to the energies of bonds between like solute atoms relative to the pure solute state. Sa.mples of the compound AuSb2 were prepared by melting stoichiometric amounts of antimony and gold (99.999 pct pure) in evacuated and sealed Vycor tubes, which were shaken vigorously and quenched in water. The ingots were annealed in evacuated and sealed tubes at approximately 700°K for 2 weeks. Metallo-graphic and X-ray examinations gave no indication of second phases or microsegregation. The samples were added from 273°K to tin-rich solutions in a solution calorimeter1 maintained at 623°K. The calorimeter was calibrated with tin; the heat content of tin, H623°K- H273°K, was taken as 4.08 kcal per g-atom.2 In each calorimetric run at least four additions were made. The total concentration of solutes in the bath at the end of any run did not exceed 1 at. pct. The measured heat effect of an addition was plotted against the average of the atom fractions x of Sb + Au in solution before and after that addition. From this plot the heat effect at infinite dilution h,,, and the composition dependence of the heat effect dh/dx in the composition range 0 < x < 0.01 were obtained. The results for the additions of antimony, mixtures of antimony and gold, and the compound AuSb2 are listed in Table I. The heat effect h on addition of a sample of the compound AuSb2 or a mechanical mixture of antimony and gold at 273°K to a tin-rich solution at 623°K can be expressed as:

Jan 1, 1969

By D. T. MacRoberts

A simple disturbance in a gas reservoir travels with a finite velocity which is nearly independent of the amplitude of the disturbance. As a result very complex transients may be set up which seriously affect observation at a well. The time of transient is much longer than commonly supposed. INTRODUCTION A change in pressure at a gas well is not propagated through the reservoir instantaneously but with a definite fin- ite velocity. Knowledge of the period ! of this transient is of value because: 1. Observations of pressure and flow-rate during the transient may affect interpretation of back-pressure tests. 2. Interference effects between wells may be used to determine continuity of formation. 3. Additional information concerning the physical characteris- tics may possibly be deduced from the behavior of a well during the transient. MATHEMATICAL DEVELOPMENT It will be assumed that the well is initially closed in and that the pressure is constant throlughout the reservoir. As the initial disturbance passes outward from the well it is further assumed that a logarithmic pressure distribution is established between the most distant point reached and the well, so that: <l> = ((/)r-<t>w) I ------------ + (/) . (1) Manuscript received at office of the Branch September 15. 1948. Paper presented at Branch Fall Meeting, Dallas. Texas. Oct. 4-6, 1948. r. = distance to any point between r and rw r = radius of drainge iw= radius of well (/) = potential (P for incompressible fluids, P2 for perfect gases) Up to the time the effect reaches the point r the production from the well will be: W= (Pr-P,,,) . (2) i b W = volume produced t = sand thickness F = fractional porosity Pr = reservoir pressure Pm = average pressure between r and rw Pb = atmospheric Pressure All pressures will subsequently be stated in atmospheres and the constant Pb will be omitted. This will be produced at a rate: dw t k (Pr³-PW2) do d 0 - . (3) log — Pw = pressure at the well k = permeability 0 = time = viscosity

Jan 1, 1949

Foreword—H. Foster Bain........................ 7 Officers and Committees......................... 9 PAPERS Growth of Metallic Crystals. By C. H. Desch...............13 Aluminum Castings of High Strength. By R. S. Archer and Zay .Teffries (With Discussion).............................35 Constitution of Alloys of Aluminum, Zinc and Tin and Aluminum, Zinc and Cadmium. By V. Jares.......................65 Exudations on Brass and Bronze. By W. B. Price and A. J. Phillips (With Discussion)..................•..........80 Preparation of Metallic Single Crystals and Twinning in Zinc and Zinc Single Crystals. By 0. E. Romig (With Discussion).............90 Plastic Deformation of a Zinc Single Crystal. By S. L. Hoyt (With Discussion) 116 Plastic Deformation of Coarse-grained Zinc. By C. H. Mathewson and A. J. Phillips (With Discussion)......................143 The Solidus Line in the Lead-antimony System. By E. E. Schumacher and F. C. Nix (With Discussion)........................195 Note on the Distribution of Energy in Worked Metals and the Effect of Process Annealing Temperature on the Final Annealing Temperature of Fine Copper Wire. By L. Zickrick and R. S. Dean (With Discussion)........207 Note on the Relation of Annealing Temperature to Conductivity of Copper Wire. Ry J. C. Bradley (With Discussion)..................210 Beryllium-copper Alloys. By W. H. Bassett (With Discussion)........218 Some Comparative Properties of Tough Pitch and Phosphorized Copper. By W. R. Webster, J. L. Christie and R. S. Pratt (With Discussion).....233 A Study of the 470" C. Transition Point in Cast 60:40 Brass. By Frances Hurd Clark (With Discussion).......................253 Strldy of the Heat Treatment, Microstructure and Hardness of 60:40 Brass. By Frances Hurd Clark (With Discussion)...............276 Corrosion and Physical Properties of Some Alloys of Aluminurn, Zinc and Tin. By N. 0. Taylor (With Discussion)..................302 Equilibrium Relations in Al-Mn Alloys of High Purity. By E. H. Dix, Jr., and W. D. Iieith (With Discussion)....................315 Deformation of an Aluminum Alloy by a Constant Load. By C. B. Sadtler and J. L. Gregg (With Discussion)....................336 Still Casting of Metals. By P. H. G. Durville (With Discussion).......343

Jan 1, 1927

Bill S.1431 for the creation of a Department of Natural Resources has received a propitious hearing before the Senate Committee on Government Operations. Interior Secretary Rogers C. B. Morton was one of the prominent witnesses who testified in favor. The department had been proposed, Morton said, with "the conviction that the development of all natural resources would be harmonized with the most practicable possible means to protect and preserve the environment, consistent with the social and economic needs of the Nation." Another opinion on the pro side came from Atomic Energy Commissioner Clarence E. Larson, who said that a "total picture" had become essential to the establishment of a policy for developing energy resources in the best public interest. Commissioner James T. Ramey, on the other hand, was one of the AEC dissenters. Ramey said he believed the reorganization of resource responsibilities would hinder efforts to deal with energy-environmental problems and prevent the use of AEC "expertise and facilities" to the greatest advantage. As Arnold Weber, associated director of the Office of Management and Budget, pointed out, however, retiring AEC Chairman Glenn T. Seaborg is in favor of the new department. Another supporter, and one who can cast a vote on the bill, is Sen. Frank E. Moss. Final Standards for emissions from new stationary sources will be published by the Environmental Protection Agency on October 27. The initial proposals, appearing in the Federal Register on August 17, called for limiting emissions per million Btu of heat input (maximum 2-hr average) to 0.2 lb of particulate matter, and, where solid fuel is burned, to 1.2 lb of sulfur dioxide and 0.7 lb of nitrogen dioxide. While the new rules are mainly for new plants, the EPA is also proposing them for "existing plants which are modified in such a way as to increase or alter. . . their emissions."

Jan 1, 1971

By D. T. MacRoberts

A simple disturbance in a gas reservoir travels with a finite velocity which is nearly independent of the amplitude of the disturbance. As a result very complex transients may be set up which seriously affect observation at a well. The time of transient is much longer than commonly supposed. INTRODUCTION A change in pressure at a gas well is not propagated through the reservoir instantaneously but with a definite fin- ite velocity. Knowledge of the period ! of this transient is of value because: 1. Observations of pressure and flow-rate during the transient may affect interpretation of back-pressure tests. 2. Interference effects between wells may be used to determine continuity of formation. 3. Additional information concerning the physical characteris- tics may possibly be deduced from the behavior of a well during the transient. MATHEMATICAL DEVELOPMENT It will be assumed that the well is initially closed in and that the pressure is constant throlughout the reservoir. As the initial disturbance passes outward from the well it is further assumed that a logarithmic pressure distribution is established between the most distant point reached and the well, so that: <l> = ((/)r-<t>w) I ------------ + (/) . (1) Manuscript received at office of the Branch September 15. 1948. Paper presented at Branch Fall Meeting, Dallas. Texas. Oct. 4-6, 1948. r. = distance to any point between r and rw r = radius of drainge iw= radius of well (/) = potential (P for incompressible fluids, P2 for perfect gases) Up to the time the effect reaches the point r the production from the well will be: W= (Pr-P,,,) . (2) i b W = volume produced t = sand thickness F = fractional porosity Pr = reservoir pressure Pm = average pressure between r and rw Pb = atmospheric Pressure All pressures will subsequently be stated in atmospheres and the constant Pb will be omitted. This will be produced at a rate: dw t k (Pr³-PW2) do d 0 - . (3) log — Pw = pressure at the well k = permeability 0 = time = viscosity

Jan 1, 1949

By F. C. Farnham

In this paper it is shown that the vertical component of the earth&apos;s magnetic field for the area of the United States can be very closely approximated by assuming it to be the sum of the vertical components of two magnetic fields. The first of these is the field of the centered dipole described by J. Bartels,l the axis of this dipole intersecting the earth&apos;s surface at two antipodal points, the one in the Northern Hemisphere being at latitude 78.5°N. and longitude 69°W., and the dipole having such strength that the vertical component of its field at its axis pole is 0.63 oersted. The second field is that due to a second dipole situated halfway between the center of the earth and a point on the earth&apos;s surface at latitude 38.5°N., longitude 91.5°W., the axis of this dipole being along this radius, the south pole being toward the surface, and the dipole being of such strength that its field at the point on the surface mentioned above is 0.069 oersted. Using the field computed on this basis, tables of latitude and longitude correction factors were computed and are included in the paper. It is also shown that the secular variation in the earth&apos;s magnetic field may be roughly accounted for by assuming it to be due to motion of the second dipole described above. Although there is an error in the equation used for computing the strength of the field due to the second dipole, the distribution of the field computed is very nearly that of the assumed arrangement of dipoles. Subsequent work by the author reveals that minor changes can be made in the location of the second dipole, which will make the computed field fit the observed field even more closely. It has also been found2 that the vertical component of the field may be represented equally well by a purely empiric relationship.

Jan 1, 1940

By H. R. Page, A. E. Jr Lee

A. E. LEE, JR. (author)—In addition to the paper we should like to make a few remarks. First, the seriousness of bending of the clay retort cannot be overemphasized. Not only did bending limit the length of the vessel, but it permitted corrosive fluid slags to concentrate in the belly of the retort and thus increased the possibility of boring. Bending also practically prohibited the use of cleanout machines and increased the danger of excessive fume losses by allowing furnace gases to escape around the top of the retort mouth. It will be noted that the Blackwell pottery practice places considerable emphasis on careful drying of retorts. Perhaps it is another smelter superstition, but traditionally the aging of retorts beyond a reasonable drying period has been considered important to long life. We are unable to give a good explanation of why aging should improve retorts. During the past fall in an attempt to prove a theory that the combined water in the clay decreased during aging, about 50 samples of wet retort collars were placed in a dry room when it was closed. Loss of weight, combined water and free moisture were measured each week over the 100 day drying period. The affinity of the dried retort for moisture makes difficult the accurate measurement of free water; however, there was a clearly defined free moisture change from about 12.5 pct when freshly made to about 2 pet at the end of 18 days, then a gradual loss to about 0.25 pet at 70 days and an apparent equilibrium near this figure through the 100th day. There was no appreciable change in the combined water. The change in weight of the average sample was, however, rather unusual, there being consistently a loss of weight throughout the entire 100 days. From the 63rd day on this leveled off to about 0.03 pet per week. These were small samples and certainly should have dried

Jan 1, 1950

By F. C. Farnham

In this paper it is shown that the vertical component of the earth&apos;s magnetic field for the area of the United States can be very closely approximated by assuming it to be the sum of the vertical components of two magnetic fields. The first of these is the field of the centered dipole described by J. Bartels,l the axis of this dipole intersecting the earth&apos;s surface at two antipodal points, the one in the Northern Hemisphere being at latitude 78.5°N. and longitude 69°W., and the dipole having such strength that the vertical component of its field at its axis pole is 0.63 oersted. The second field is that due to a second dipole situated halfway between the center of the earth and a point on the earth&apos;s surface at latitude 38.5°N., longitude 91.5°W., the axis of this dipole being along this radius, the south pole being toward the surface, and the dipole being of such strength that its field at the point on the surface mentioned above is 0.069 oersted. Using the field computed on this basis, tables of latitude and longitude correction factors were computed and are included in the paper. It is also shown that the secular variation in the earth&apos;s magnetic field may be roughly accounted for by assuming it to be due to motion of the second dipole described above. Although there is an error in the equation used for computing the strength of the field due to the second dipole, the distribution of the field computed is very nearly that of the assumed arrangement of dipoles. Subsequent work by the author reveals that minor changes can be made in the location of the second dipole, which will make the computed field fit the observed field even more closely. It has also been found2 that the vertical component of the field may be represented equally well by a purely empiric relationship.

Jan 1, 1940

By Robert H. Carpenter

Molybdenite mineralization occurs in the hood zone of the Questa mine aplite-porphyry intrusive, one of the three sil ica-rich intrusive5 occurring along the east-west trending Red River Trench that crosses the northerly trending Sangre de Cristo Mountains in north-central New Mexico. The Trench is located immediately north of the circular Gold Hill positive block between the Red River and Cabresto Creek drainages. The aplite-porphyry bodies intruded a mid-Tertiary volcanic section consisting of lower andesites, overlain by latites and rhyolites. They occur largely in the andesites and were emplaced mainly by metasomatism rather than by sloping. Hydrothermal alteration occurs both as blanket propylitization in the volcanics and sericitization and kaolinization in the porphyries and as halo-type alteration outward from veins and shear zones resulting in strong biotization in the volcanics and sericitization and kaolinization in the aplitic rocks. Mineralization consists of: ( 1) molybdenite- quartz veinlets; (2) banded molybdenite, quartz veins frequently with biotite and potash feldspar along the walls and occasionally with minor lead, zinc, and copper sulfides and with fluorite and carbonates when again reopened; ( 3) high grade molybdenite locally along shear zones; and ( 4) molybdenite paint along joint and fracture surfaces. The mineralization was associated with faulting that resulted from numerous periods of gravity adjustment along the Trench and was controlled by the major shear systems that trend northeast, east-west and north-south to northwest. Molybdenite has been well oxidized in nearsurface exposures to ferrimolybdite and the molybdenum-bearing ferric hydroxide, akaganeite. The oxidation of the abundant pyrite within the veins and shear zones and of the alteration pyrite in the volcanics resulted in a low pH environment under which the acid molybdate ion released by oxidation was fixed either in the ferrimolybdite or the akaganeite molecule in the veins and shear zones or in the soils. Little has been lost in the runoff.

Jan 1, 1968

By W. C. Ellis, M. E. Fine

WHEN certain binary Fe-Ni alloys are worked cold and then stabilized by a stress-relief anneal, their Young&apos;s moduli are nearly invariant over a substantial temperature range determined by composition and work-anneal history.&apos; In the present investigation addition of molybdenum to such alloys (besides increasing the yield strength) was found to diminish the sensitivity of the thermal coefficient of Young&apos;s modulus to composition changes. Such alloys are of interest for applications requiring 1 a metal with controlled, low temperature coefficient of Young&apos;s modulus and substantial magnetic permeability.&apos; Young&apos;s modulus ordinarily decreases with rising temperature. In ferromagnetic alloys a change in modulus on heating due to loss of ferromagnetism modifies the .temperature dependence. Far below the Curie temperature ferromagnetism alters the modulus in two ways: a—Addition of the energy of magnetization, a function of interatomic distance, changes the relation between interatomic energy and distance.&apos; This lowers the modulus in the Fe-Ni and Fe-Ni-Mo alloys of this investigation. b—An applied stress changes the ferromagnetic domain arrangement so that linear magnetostriction contributes to the strain and further lowers the modulUs.~ Since in the alloys of this investigation both effects lower the modulus, loss of ferromagnetism on heating changes the slope of the modulus-temperature curve in a positive direction. With increasing temperature the slope of the modulus-temperature curve, due to progressive loss of ferromagnetism, becomes less negative, goes through zero (the modulus is minimum), becomes positive, and resumes its normal negative value above the Curie temperature.&apos; The increase in modulus and decrease in curvature in the modulus-temperature curve occurring on work hardening have been attributed to a reduction in effect (b).&apos;. Vn the absence of ferromagnetism work hardening through introduction of residual strains would be expected to decrease the modulus.&apos; Alloy Preparation—Test Methods Four series of alloys having nominal molybdenum contents of 5, 7, 9, and 10 pct and containing 47 to 58 pct Fe (the analyzed compositions are given in Table I) were melted in air and cast as bars weighing from 2 to 6 lb. The charge consisted of electrolytic nickel, Armco iron, molybdenum (99+ pct) or ferromolybdenum (62 pct Mo), manganese, and aluminum as a deoxidizer. The bars were swaged cold to the desired diameters with intermediate anneals. Alloys in this composition range are reported" to be face-centered cubic and ferromagnetic at room temperature. The Curie temperatures" decrease with molybdenum. For example, keeping the Ni/Fe ratio at unity and increasing the molybdenum from 0 to 17 pct decreases the Curie tempera- ture from approximately 500°C to room temperature. (The 17 pct Mo alloy requires quenching to retain a single phase.~) Young&apos;s modulus at a series of temperatures from —50" to 100°C was determined by a dynamic method previously described.&apos;, " In this method Young&apos;s modulus is calculated from the resonant frequency (in this case approximately 50,000 cycles per second) of a rod sample (approximately 2 in. long) vibrating longitudinally in the first mode. The densities of the samples at room temperature, Table I, were determined by the standard method of weighing in air and reweighing in redistilled bromobenzene. The linear coefficients of expansion, Table I, needed to calculate the sample length and density at the temperature of measurement, were obtained by observing the change in length (22" to 100°C) of an 8 in. gage distance with a two microscope cathetometer. The values of density and coefficient of expansion in the few samples checked are independent of treatment to the accuracy reported. This was assumed to be general for all the samples. The modulus values are accurate to &0.05x101&apos; dynes per sq cm. However, values of thermal change in modulus are accurate to 20.005~ 10" dynes per sq cm. Young&apos;s Modulus Values at 25°C: The modulus values of O&apos;, 5, and 10 pct Mo alloys at 25 °C are plotted in Fig. 1 as functions of nickel. After working cold, the samples were either recrystallized at 950" to 1000°C or given a low temperature stabilizing anneal at 400° C. The 400°C anneal does not reduce the hardness nor cause recrystallization. Annealing at 400 °C does

Jan 1, 1952

By Lyon F. Terry

IN contemplating the prospects of natural gas being transported from the fields where it is produced to such distant points as Philadelphia, New Jersey, New York City, and New England, let us review the advance that natural gas has made and the projects currently scheduled for construction. This may give us a perspective of the point in the long-range development of the natural gas business in which we now find ourselves, and some basis for judging the further expansion of the industry. Authentic statistics of the total marketed production of natural gas in the United States have been compiled by the Bureau of Mines since the year 1906. The growth of the business is indicated by the following data on marketed production for each ten-year interval since 1906:

Jan 1, 1947

By AIME AIME

IN ORDER to carry on its work most effectively, the Committee on Industrial Organization (now known as the Committee on Industrial Relations) consists, of .a number of sub-committees, each composed of a chairman and members who are especially fitted to carry out the work designated by its title. With only one or two exceptions, all of these committees made reports at the New York meeting of the Institute, in February of this year, abstracts of which follow.

Jan 1, 1920

Oct. 8 to 13, inclusive, 1917 COMMITTEES Committee on Arrangements H. A. BUEHLER, Chairman W. E. MCCOURT, Secretary C. J. ADAM L. L. HUTCHISON VICTOR RAKOWSKY J. A. CASELTON EUGENE MCAULIFFE J. D. ROBERTSON .F. W. DEWOLF P. N. MOORE ARTHUR THACHER E. F. GOLTRA MRS. P. N. MOORE H. A. WHEELER Committee on Ladies&apos;, Entertainment MRS. PHILIP N. MOORE, Chairman MRS.. W. E. MCCOURT, Vice-Chairman MRS. D. M. ARMISTEAD MRS. R. G. HALL MRS. A. A. BONSACK . MRS. J. W. HEGELER MRS. B. F. BUSH MRS. J. N. HOUSER MRS. G. 0. CARPENTER MRS. EUGENE MCAULIFFE MRS. F. V. DESLOGE MRS. RUDOLPH PORTER MRS. F. W. DEWOLF MRS. N. P. ROOD MRS. A. W. DICKINSON MRS. ARTHUR THACHER

Jan 12, 1917

MISCELLANEOUS U.S. 0,029,598 - Extraction of vanadium values from vanadiferous iron oxide ore. A pelletized mixture of ore, limestone and bentonite is roasted in an oxidizing atmosphere to form calcium vanadates, the calcine ground, the ground material leached with aqueous ammonium carbonate or sodium carbonate to produce a vanadium-rich solution while leaving an insoluble residue of calcium carbonate and/or calcium bicarbonate along with undissolved iron values, and the solution separated and treated for its vanadium content. This patent is a reissue of U.S. Patent No. 3,853,982, dated Dec. 10, 1974. C. B. Bare and J. W. Pasquali, assigned to Bethlehem Steel Corp. Mar. 28, 1978. 7 pp. (423-68). Filed: 3-3 1-77 (783,352).

Jan 1, 1979

By H. C. Babbitt

The Effect of Arsenic.—A question involving the temperature of precipitation of ammonium phospho-molybdate, which was brought to my attention some time ago, led to the following experiment :*

Jan 1, 1893

By W. M. McKewan

Dense magnetite pellets were reduced in hydrogen-water vapor-nitrogen mixtures over a temperature range of 400° to 500° C at a pressure of 0.97 atm. The rate of reduction per unit area was found to be constant with time and directly proportional to the partial pressure of hydrogen at a constant ratio of water vapor to hydrogen. Water vapor poisoned the oxide surface by an oxidizing reaction and markedly slowed the reduction. The enthalpy of activation was found to be + 13,600 cal per mole. THE investigation of the reduction of iron oxides has been the subject of numerous papers. Most of these papers have dealt with the evaluation of various ores, both magnetite and hematite. There have

Jan 1, 1962

By William G. Pariseau

The extraction ratio approach to pillar design in flat seams is based on a mathematically exact analysis that is a reasonable physical approximation to room-and-pillar layouts in many instances. The essentials of the approach are reviewed and then mathematically approximate formulas for pillar design in inclined seams of arbitrary dip are proposed. Detailed numerical analysis of stress about a typical 5 entry, 4 pillar panel at dips of 0, 15, 30, 45, 60, 75 and 90 degrees at low and high extraction ratios show that the proposed inclined seam extraction ratio formulas for pillar normal and shear stresses, although conservative, have an accuracy quite adequate for engineering purposes. Appropriate pillar safety factors for compressive and shear failure and a safety criterion for overturning are specified.

Jan 1, 1982