Search Documents

By Donald E. Meyer

High current-low voltage EB-gun evaporation in an oil-free ultra-high vacuum system was found to be necessary, though not sufficient, for stability (300°C, 106 v per on) of aluminium gate MOSFET's and MOS capacitors not stabilized by a phosphorous glaze. five characteristics of the equipment used: 1) Vacuum purification of the aluminum charge, 2) Ionization of the evaporant by the electron beam, 3) X-ray formation, 4) Residual gases during evaporation, and 5) Metal film structure were studied as Possibly significant in MOS fabrication. EVAPORATION of contact metals common to the semiconductor industry historically has been accomplished with oil diffusion pump systems and various resistance heated evaporant sources as dictated by the type of metal evaporated. To meet a need for greater reliability of semiconductor devices, other metallization methods were developed. A good example would be application of the moly-gold contact system to integrated circuits with deposition by RF or triode sputtering.' More recently, fabrication of stable metal-oxide-silicon devices and circuits has put new demands on metallization. The purity of the thin metal films composing MOS structures is critical, particularly at the metal-oxide interface, and ultra-high vacuum metallization using sputter-ion pumping and electron beam gun (EB-gun) evaporation are well suited for the task. At this laboratory aluminum has been the most common contact-gate metal for both MOS capacitors and MOSFET's. In the earliest work with MOS capacitors, aluminum was evaporated from wetted tungsten filaments using both diffusion pump and ion pump vacuum systems. In spite of clean oxide techniques these capacitors were unstable under bias-tempera-ture stressing. Only after a switch to EB evaporation of aluminum were stable capacitors produced. Using the same techniques it was possible to make MOSFET's with equivalent stability. Stability data for a discrete MOSFET is shown in Fig. 1. This is a "clean" oxide gate (no phosphorus stabilization or no etch back of a thicker gate) having a thickness of lOOO? thermally grown on the (111) plane. Gate length after diffusion was 0.24 mils, and the devices were hermetically sealed. Stressing conditions were 300°C and 106 v per cm applied alternately as a positive and negative field for 10 min, 50 min, and 4 hr for a total stress time of 10 hr. An initial shift in turn-on voltage of 0.1 v was detected for 10 min of positive bias. All evidence at this laboratory indicated that while EB-gun evaporation of ultra-high purity aluminum was not sufficient for 300°C stability, it did seem to be necessary. There may well then be something inherent in the EB-gun deposition used which enhanced stability, and probably no single factor existed but rather a series of factors. It is the purpose of this paper to report on some of the investigations carried out to learn more about EB-gun evaporation in ultra-high vacuum systems. EXPERIMENTAL DESCRIPTION The EB-gun was self accelerated, had a maximum power rating of 10 kw, and used a water-cooled copper crucible able to hold a 20-g aluminum charge. The electron beam was bent 180 deg and focused by an electromagnet which also provided movement of the beam across the crucible. Normal power conditions in this work were 9 kv and 300 to 600 mamp. The gun can be described as high-cur rent/low-voltage and was quite different in its mechanism of operation from EB-guns with much higher acceleration potentials. An oil-free vacuum system capable of 5 x 10- l0torr, a quartz crystal rate and thickness monitor and a quadruple mass spectrometer completed the evaporation system, Fig. 2. A typical evaporation cycle consisted of a 3 to 4 hr pumpdown to the upper l0-9 range and evaporation at l0? per sec with the pressure in the bell jar not rising above 1 x 10"7 torr. Thickness control was 5 pct or less and could be automatically monitored and controlled. Five phenomena associated with the EB evaporation and considered as possible contributors to Ma performance included a purification effect, ionization of evaporating aluminum, X-rays, constitution of vacuum ambient during evaporation, and film structure dependence upon evaporation rate. These phenomena are now discussed. Vacuum Purification. The design of the EB-gun permitted purification of the aluminum charge by vacuum outgassing. Particular features included an efficiently water-cooled copper hearth with a capacity of over 20 g of aluminum and the capability for sweeping the beam across the charge. Such capacity meant that aluminum had to be added only after about every fifth evaporation. A new charge was not required each evaporation as is necessary with filament evaporation. An oxide "scum" which appeared on the charge could be completely cleared from the top hemisphere of the charge by sweeping with the beam prior to opening the shutter. An indication of the purifying effect was obtained by a series of analytical measurements on incoming aluminum, after melting but with little vacuum out-gassing, after 30 min outgassing, and the evaporated film itself. Either a solids (spark source) mass spectrometer or an emission spectrometer were used for analyzing the aluminum charge. Analysis of the evapo-

Jan 1, 1970

By C. E. Lundin

The Ce-H system was investigated in the temperature range, 573° to 1023°K, and the pressure range, 10-3 to 630 Torr, as a function of 'composition up to 72 at. pct H. Families of isothermal arid isopleth curves were plotted from the pressure-terr~perature-composition relationships. From these curves the solubility relationships were determined for the system. The isopleths are analytically represented by equilibrium dissociation pressure equations. The relative partial molal enthalpzes and entropies of solution of hydvogen in the systerrz were calculated fronz the dissociation pressure equulions and are tabulated. The integral free energies, enthalpies, and entropies of mixing in the Ce-H system were determined from the relative partial quantities and are also tabulated. The standard free energy, enthelpy, and entvopy of reaction of the dihydride phase at kcal per kcal per mole H2, and ?S° = -34. 1 cal per deg mole H2, respectively. The equilibrium dissociation pressure equation in the two-phase region is: UNTIL recently very little was known of the detailed solubility and thermodynamic relationships of the Ce-H system. Two previous investigations1,2 are noteworthy. However, significant discrepancies and omissions exist on analyzing them. The work of Mulford and Holley1 on cerium did not clearly delineate the boundaries of the two-phase region, Cess - CeH2-x. The plateau partial pressures were not thoroughly defined and were considerably displaced in pressure compared to those from the work of Warf and Korst.2 These latter authors concentrated their studies primarily from 823° to 1023°K in the pressure range of 1 to 760 Torr. No data were determined to outline the regions of primary solid solubility and the hydride phase. Also the establishment of the plateau partial pressures was rather limited in scope. In neither work was a treatment conducted of the relative partial molal enthalpies and entropies of solution of hydrogen in the single-phase regions and the integral thermodynamic quantities of mixing throughout the system. Therefore, it was the objective of this research to determine the complete equilibrium solubility relationships and thermodynamic data for the system by pressure-temperature-composition studies. EXPERIMENTAL PROCEDURE The cerium metal for this study was donated by the Reno Metallurgy Research Center of the Bureau of Mines. Total impurity content was 0.13 pct with only 60 ppm O. The metal was checked metallographically and contained only minor amounts of second phase compared to cerium from other sources. Specimen preparation was done in a dry box flushed with argon gas. The surface of a small rectangular piece of cerium (about 0.2 g) was filed with a clean, mill file. Final weighing was done in a tared enclosed vial containing argon gas. The specimen was then loaded quickly into the reaction chamber which was purged several times with high-purity hydrogen gas and then allowed to pump to about 10-6 Torr. The furnace was heated to the reaction temperature and the run started. The equipment used to conduct the hydriding was a Sievert's-type apparatus. Basically it consisted of a source for pure hydrogen, a precision gas-measuring burette, a heated reaction chamber, a McLeod gage, and a mercury manometer. Pure hydrogen was supplied by the thermal decomposition of uranium hydride. The 100-ml precision gas burette was graduated to 0.1-ml divisions and was used to measure the quantity of gas and admit it to the chamber. The reaction chamber was a quartz tube. Prior to each run, the cerium specimen was wrapped in a tungsten foil capsule to prevent reaction of the cerium with the quartz. Control of the temperature was achieved within ±1°K. Pressures in the manometer range were measured to ±0.5 Torr and in the McLeod range (10-3 to 5 Torr) to ±3 pct. The compositions of hydrogen in cerium were calculated in terms of hydrogen to cerium atomic ratio. These compositions were estimated to be ±0.01 H/Ce ratio. The technique used to study the equilibrium pressure-temperature-composition relationships of the Ce-H system was to develop experimentally a family of isothermal curves of composition vs pressure. The range of pressure through which each isotherm was developed was from 10-9 to about 630 Torr in the temperature interval, 573° to 1023°K. RESULTS AND DISCUSSION The hydriding characteristics of cerium are iso-morphous with those of the elements of the light-rare-earth group (lanthanum, cerium, praseodymium, and neodymium) wherein the region from the dihydride to trihydride is continuously single phase.' The structure of this phase is fcc.3 The heavy rare earths form a trihydride,2 which is hcp, separated by a two-phase region from the fcc dihydride phase. The Ce-H system is represented by the family of experimental isotherms in Fig. 1. Due to the small scale required to draw the curves, the experimental points are omitted; however, a total of 240 experimental data points were taken to prepare these curves. The solubility relationships can be deduced therefrom. Three distinct regions of partial pressure and composition can be seen. The region of cerium solid solution is represented by the rapidly rising isotherms in the dilute composition range. In accordance with Gibbs Phase Rule only one solid phase, the cerium solid so-

Jan 1, 1967

By R. J. Fruehan, F. D. Richardson

Electrochemical measurements have been made of the activity of oxygen in copper and its alloys with silver and tin at 1100" and 1200°C. The galvanic cell used was Pt, Ni + NiO/solid ellectrolyte/[O] in metal, cermet, Pt The results do not support any of the equations so far designed for predicting the activities of dilute solutes in ternary solutions from activities in the corresponding binaries. If, however, a quasichemical equation is used with the coordination number set to unity, agreement between observed and calculated activities shows that this empirical relationship can be useful over a fair range of conditions. SEVERAL solution models have been proposed for predicting the activity coefficients of dilute solutes in ternary alloys from a knowledge of the three binary systems involved. Alcock and Richardson1 have shown that a regular model, and a quasichemical model,' in which the dissolved oxygen is coordinated with eight or so metal atoms, can reasonably predict the behavior of both metal and nonmetal solutes when the heats of solution of the solute in the separate solvent metals are similar. But when this is not so, neither model gives useful predictions unless coordination numbers of one or two are assumed. Wada and Saito3 subsequently adopted a similar model to derive the interaction energies for two dilute solutes in a solvent metal. Belton and Tankins4 Rave proposed both regular and quasichemical type models in which the oxygen is bound into molecular species, such as NiO and CuO in mixtures of Cu + Ni + 0. However, their models have only been tested on systems in which the excess free energies of solution of the solute in the two separate metals differ by a few kilocalories. Ope of the reasons why more advanced models have not been proposed is because few complete sets of data exist for ternary systems in which the solute behaves very differently in the two separate metals. For this reason measurements have been made of the activities of oxygen dissolved in Cu + Ag and Cu + Sn. Measurements on both systems were made by means of the electrochemical cell, Pt, Ni + NiO/solid electrolyte/O(in alloy), cermet,Pt [1] The activity of oxygen was calculated from the electromotive force and the standard free energy of formation of NiO, which is accurately known.5 Before investigating the alloys, studies were made of oxygen in copper to test the reliability of the cell and to check the thermodynamics of the system. Of the previous studies those by Sano and Sakao,6 Tom-linson and Young,7 and Tankins et al.8,7 have been made with gas-metal equilibrium techniques; those by Diaz and Richardson,9 Osterwald,10 wilder," Plusch-kell and Engell,12 Rickert and wagner,13 and Fischer and Ackermann14 have been made by electrochemical methods. EXPERIMENTAL The apparatus employed was the same as described previously,9 apart from slight modification. The molten sample of approximately 40 g was held in a high grade alumina crucible 1.2 in. OD and 1.6 in. long. The solid electrolytes were ZrO2 + 7½ wt pct CaO and ZrO2 + 15 wt pct CaO; the tubes 4 in. OD and 6 in. long were supplied by the Zirconia Corp. of America. They were closed (flat) at one end. In one experiment with Cu + O, both electrolytes were used in the cell at the same time. The reference electrodes inside the electrolyte tubes consisted of a mixture of Ni + NiO. They were made by mixing the powdered materials and pressing them manually into the ends of the tubes, with a platinum lead embedded in them. The tubes were then sintered overnight in the electromotive force apparatus at 1100°C. By sintering the powders inside the tubes (instead of using a presintered pellet9) better contacts were obtained between the electrolyte, the powder, and the platinum lead. Troubles arising from polarization9 were thus much reduced. The electromotive force was measured by a Vibron Electrometer with an input impedence of 1017 ohm; the temperature was measured with a Pt:13 pct Rh + Pt thermocouple protected by an alumina sheath. The couple was calibrated against the melting point of copper. The cermet conducting lead of Cr + 28 pct Al2O3, previously found to be satisfactory9 for use with Cu + 0 was also found satisfactory with Cu + Ag + 0 and Cu + Sn + 0. Superficial oxidation was observed, but it did not interfere with the working of the cell. The reaction tube containing the cell was closed at each end with cooled brass heads and suspended in a platinum resistance furnace. The tube was electrically shielded by a Kanthal A-1 ribbon which was wound round it, and the ribbon was protected by a N2 atmosphere between the furnace and the reaction tube. The cell was protected by a stream of high purity argon which was dried and passed through copper gauze at 450°C and titanium chips at 900°C. All the metals used were of spectrographic standard. Procedure. In studies of the system Cu + 0, be-

Jan 1, 1970

By R. E. Cech, J. H. Hollomon

KURDJUMOV and Maksimova reported experiments with manganese steels and high carbon steels' and with an Fe-Ni-Mn alloy' in which mar-tensite was formed isothermally over a range of temperatures. They found in some cases that mar-tensite formation could be suppressed by rapid quenching to liquid nitrogen temperature. From their microstructural observations of martensite formed isothermally, they concluded that the rate controlling step is nucleation rather than growth. Kulin and Cohen,3 in an attempt to reproduce these experiments, found that with a steel having the same composition as that reported by Kurd-jumov and Maksimova, the transformation to martensite was essentially complete above the temperature range of Kurdjumov and Maksimova's isotherms. The possible reasons for this disagreement were not considered. Recent papers by Das Gupta and Lement4 and Kulin and Speich5 report the formation of isothermal martensite in a high chromium steel and in an Fe-Cr-Ni alloy, but neither paper can be considered a verification of the original Kurdjumov and Maksimova results. Further, in neither case were the authors able to suppress the formation of martensite entirely. Because of the important bearing the Kurdjumov and Maksimova results have to an understanding of the mechanism of martensite reactions it was felt that an experimental investigation directly concerned with checking the validity of their results was in order. This paper describes the results obtained on the isothermal transformation over the temperature range from —79" to —196°C of an alloy of iron, nickel, and manganese. Experimental Apparatus A 15 lb heat of an alloy containing 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn was melted by induction and cast under argon. The ingot was forged to 1-in. bar and a portion rolled to 1/16x1 1/2-in. strip. This strip was pack-homogenized 300 hr at 1100" in a helium-filled sealed iron tube. The composition after homogenization was 73.2 pct Fe, 22.94 pct Ni, 3.73 pct Mn, 0.05 pct C, and 0.015 pct N. The strips were cut to 1/2-in. width for dilatometer and metal-lographic specimens. Only the center portion of the 11/2-in. strip was used in the present investigation. The dilatometer employed was similar in design to one described by Flinn, Cook, and Fellows." A concentric fused auartz rod and tube assembly with hooks for holding the specimen was mounted so as to transmit the specimen dilation to a 1/10,000 in., 1/10 in. travel dial gage. The dilatometer proper was mounted by means of extension arms to a counterweighted sliding member on a vertical standard. This method of mounting permitted rapid transfer of the dilatometer from the austenitizing furnace to the quenching bath and low temperature chamber. A small electrical vibrator on the dilatometer kept frictional effects of the quartz members at a minimum. The austenitizing unit was a vertical, molybdenum-wound, hydrogen atmosphere furnace maintained at a constant temperature ±3°C by means of constant power input. A 12-in. stainless steel jacketed copper liner having 1/2-in wall thickness acted to equalize the temperature in the hot zone of the furnace. This liner, closed at the bottom end and open at the top to permit entrance of the dilatometer and specimen, was kept filled with dry nitrogen gas. A chromel-alumel thermocouple was placed inside the tube to determine the temperature. The 4-in. dilatometer specimens in the chamber varied less than 1/2° across the specimen length except for a 1 1/20 drop at the end nearest the open end of the furnace. The low temperature isothermal holding bath was a double Dewar arrangement similar to one described by Turnbull7. The outer bath was filled with a refrigerant at a temperature lower than the desired holding temperature. The inner bath was filled with Freon "11" or "12" or a mixture of both, depending upon the holding temperature. This inner bath which tended to be cooled by the outer bath was kept at a constant temperature by introducing a small amount of heat with a manually controlled electric heater. Stirring was accomplished by bubbling dry air through the bath. A Leeds and North-rup type K potentiometer was used to measure the inner bath temperature as indicated by a five element copper-constantan thermopile. The bath temperature was maintained within ±0.2°C of the desired temperature by occasionally adjusting the heater current so as to keep the Leeds and Northrup galvanometer at zero deflection with a constant setting of the potentiometer. Isothermal tests were usually continued for 300 to 400 min and another reading made at approximately 1000 min if the bath, unattended overnight, had not deviated in temperature more than 5°C. Transformation curves are drawn dashed (Fig. 1) through the time region where temperature was not controlled precisely. Experimental Procedure Dilatometer specimens of 1/2x1/16-in. strip were cut to 41/2-in. length and holes were drilled for the quartz hooks with proper spacing to give a 4-in. measured length. A thermocouple consisting of 0.012-in. diameter chrome1 and alumel wires was spot welded to the specimen and threaded between the dilatometer rods to binding posts near the dial

Jan 1, 1954

By B. N. Das, J. B. Darby, P. A. Beck, Y. Shimomura

A POWDER pattern for the (Cr, Mo, Co)R-phase annealed at 1200°C was reported in 1951.1 Through the courtesy of Prof. D. P. Shoemaker of Massachusetts Institute of Technology the authors became aware of inconsistencies of this pattern with that to be expected from the structure of the R-phase, as determined by Komura, Shoemaker, and Shoemaker.' In addition, Professor Shoemaker also noted that the powder pattern reported8 for the (Cr, Mo, Co)D-phase, annealed at 1300°C, agreed fairly well with that to be expected from the newly determined structure of the R-phase. In view of these findings, the previously reported powder patterns of the R-phase and of the D-phase were compared carefully. It was found that most lines in the two patterns (22 lines) were to a fair degree of accuracy related to each other by a single conversion ratio for the corresponding d spacings. The value of the conversion ratio was found to be 1.0058, so that the d spacings of the D-phase pattern previously reported were larger than the correspond- ing d spacings for the reported R-phase pattern by approximately that factor. The intensity relationships between corresponding lines in the two patterns were similar, as judged visually. The following exceptions were noted: Lines Nos. 2, 3, 19, 20, 21, 22, 23, 24 and 25 of the D-phase pattern,:' all designated weak or very weak, were missing in the apparently somewhat fainter R-phase pattern used.' Lines 1, 2, 3, 5, 15 and 34 (all weak or very weak), reported for the R-phase, were missing in the D-phase pattern, Table I. In view of these observations it seemed probable that the two patterns differed from each other mainly by a slight change in lattice parameters (with c/a remaining approximately constant), and that the pattern previously reported for the R-phase contained some weak extraneous lines, most likely to be attributed to impurities. In order to check the foregoing assumption, two specimens of an alloy containing 43 pct by weight of cobalt, 41 pct molybdenum, and 16 pct chromium, which was within the composition range of stability of both the D-phase at 1300°C and of the R-phase at 1200°C, were homogenized at 1200 and 1300°C, respectively, and quenched. X-ray diffraction patterns of the powders of these two specimens, obtained with CrK radiation, were compared carefully with each other and with the D-phase pattern previously

Jan 1, 1959

By John S. Crout

TWENTY-FIVE years ago the training of an engineer was of interest solely to the educator and to the student entering the field. At that time the engineer's position in society was relatively simple. His training emphasized design and operation and he expected to enter industry to handle the engineering problems of raw materials production, mechanical and product design, and the operation of power plants, factories, transportation and communication systems, and similar phases of industrial activity. He was not concerned with or particularly interested in the problems of management, administration, sales, publicity, industrial relations, or of legislation. To a large degree he was content to leave these matters to self-made businessmen, or men trained in law, finance, or commerce. That period in the evolution of the engineer is now history. It is generally conceded that the modern world is dependent upon engineering technology for its day-to-day survival. The continued operation of facilities on which mankind relies is dependent upon the functioning of mines, utilities, chemical plants, and other factories, all of which require the knowledge and the skills of trained engineers. Thus from a purely mechanical point of view, the engineer has become indispensable to

Jan 1, 1947

By A. Karim, T. G. Langdon, C. Y. Cheng, J. E. Dorn

The effect of changes in temperature and stress on the creep behavior of Fe-4 pct Si was investigated over the temperature range from 650° to 1175K Over the temperature range of 799° to 110l°K, the shear strain rate, ?', obeys the relationship: where K is a constant, 7 the applied shear stress, G the shear modulus, g the free activation energy for diflusion, R the gas constant, and T the absolute temperature. The results strongly suggest that the creep in this alloy is controlled by a dislocation climb mechanism. In a recent investigation, Ishida, Cheng, and Dorn1 observed that the apparent activation energy for creep of a! Fe from 480" to 775°K corresponded to that for self-diffusion. Over the magnetic transformation range (775" to 1045"K), the apparent activation energy for creep increased steeply with increasing temperature in agreement with the known decrease in the free activation energy for self-diffusion. Passing through the Curie temperature, the apparent activation energy decreased abruptly following which it then increased mildly as the temperature further increased. Inasmuch as the apparent activation energy for creep of a! Fe below the Curie transformation range of temperatures appeared to decrease with increasing values of the stress, the data were analyzed in terms of a model based on the nonconservative motion of jogged screw dislocations. But since the observed creep rate was much higher than that which could be accounted for on the basis of usual models, the authors found it necessary to assume that pipe diffusion became significant over the lower temperature range. Furthermore, the abnormally high activation energy for creep above the Curie temperature was attributed to grain boundary migration which became prevalent in this temperature range. It was thought that a number of the interesting issues that arose in the creep of a Fe might be resolved by investigating the creep of Fe-4 pct Si alloy: This alloy has about the same Curie range and therefore should give creep results that closely parallel those for a Fe and in this way provide comparable data for analysis of creep mechanisms. Furthermore, it can be annealed at higher temperatures which could provide some stabilization against grain boundary migration. In addition, it might serve to illustrate the possible effects of short-range ordering on creep.

Jan 1, 1969

By J. P. Hirth, A. H. Clauer

A simple graphical method is presented for the determination of climb forces on dislocations exerted by uniaxial stresses. In conjunction with standard stereographic projections, the technique is applicable for any crystal system. Climb forces on glide dislocations in bcc crystals are determined as an application. In connection with a study1 of elevated temperature creep of molybdenum single crystals, a detailed analysis of the climb force on a dislocation was necessary. In general, such forces can be calculated for an arbitrary dislocation segment from the Peach-Koehler equation2 (or one of its variants3"6) where Fk are the components of the force per unit length of dislocation line, ?i of the unit sense vector tangent to the line, ojl of the stress tensor, bl of the dislocation Burgers vector, and is the Einstein permutation operator with components ?123 = ?231 = ?321 = —?132 = — ?321 = —?—213 = unity, and all other components zero. It is understood in the suffix notation of Eq. [I.] that repeated indices are to be summed over 1, 2, and 3. For the most general coordinate system, the matrix manipulations required to solve Eq. [I] are fairly complex. However, a simplification can be achieved by specifying a coordinate system based on the dislocation in question. The pertinent system involves cartesian coordinates xi, x;, xi, with attendant unit vectors e'i; ei being parallel to the Burgers vector b, and e'3; being parallel to the climb directions (b x ?), i.e., normal to the slip plane. In this coordnate system b = (bi, 0, 0) and ? = (?'1,?'2, 0). Hence, Eq. [I] yields for the climb force per unit length F3 = ?'2s'11b'1—?'1s'12b'1 [2] The first term on the right side of Eq. [2] is the climb force on the edge component of the dislocation, while the second is the (cross-slip) force normal to the glide plane acting on the screw component. Thus, the problem of determining the climb force reduces to that of resolving the stress components —il and s'12 in the xi coordinate system. Several authors7- l0 have shown, for the glide case, that such stress resolution can be performed most readily by graphical methods. Therefore, we present a similar method for the climb case. Of the suggested methods, we follow that of Hartley and Hirth,9 which can be performed directly with a standard stereographic projection for the crystal system in question. We treat the case of simple tension, or compression, this being the most common creep test in which climb is important. A set of cartesian coordinates (x1, x2, x3) is fixed with x3 parallel to the specimen axis. This set is connected to the x'i set by the factors defined in Table I. A perspective view of the coordinate systems relating them to the glide ellipse, is given in Fig. 1, while a stereographic projection of the coordinate systems is presented in Fig. 2. The transformation matrix connecting the xi and xi coordinates is x'i =aijXj [3] where an a11 a13 aij = a21 a22 a23 a31 a23 [4] s The corresponding transformation for the stresses is i [5] The only nonzero component of okl for the simple tension case is s33,. Hence, using Eqs. [4] and 151, we find that Eq. [2] becomes F3 = b'1s33 sin2 cos ?[cos ? sin a - sin ? cos a] [6] = m1b'1s033 sin a- rn2b's33 cos a where sin a = 5: and cos a = ?i, with a the angle measured from b to ?, i.e., a polar angle in the x1, x2 plane. The same equation with a sign change applies for compression. A graphical plot of the "Schmid" factor m1, relating to the climb force on the edge component, is presented in the stereographic projection of Fig. 3. In this projection the glide plane normal points toward the top of the page and the glide direction points normal to the plane of the page. To use the graph, one

Jan 1, 1970

By C. Law McCabe, R. G. Hudson

The Knudsen cell has been employed to determine the free energy of formation of Mn7Cs in the temperature range 800" to 950°C. A value of 66,440 cal was found for hH°o for a-manganese. Measurements of the pressure of manganese over a mixed carbide, (Fe,Mn),C, points to a power relationship between aun7cs and N.4,. RECENTLY Kuo and Perssonl have reported that the carbide of manganese which is in equilibrium with graphite at temperatures up to 1100° C is Mn7Ca. There are no published data on the thermo-dynamic properties of this compound. In order to determine the stability of Mn7Ca, it appeared that, by obtaining the pressure of manganese above 8-manganese and also above Mn,C, in equilibrium with graphite, the free energy of formation of Mn7Ca from 8-manganese and graphite could be obtained. In addition, the vapor pressure of manganese, reported by Kelley From data of Bauer and Brunner,' is subject to some uncertainty and further determinations of the vapor pressure of manganese seemed warranted. In this investigation of the pressure of manganese vapor above pure manganese and also above the carbide of manganese in equilibrium with graphite the apparatus used is the Knudsen orifice cell. The same apparatus, experimental procedure, and method of calculating the pressure was used in this investigation as in one previously reported.~ Care was taken to insure that the cells were at constant weight before using them in a run. The manganese charged in the cell was CP grade powder, carbon free, obtained from the Fisher Scientific Co. A spectroscopic analysis of the manganese after appreciable amounts of it had vaporized from the Knudsen cell showed that no element was present in sufficient quantities to contribute to a weighable weight loss or to decrease the vapor pressure of manganese to any appreciable extent. The spectro-graphic analysis was 0.002 pct Cu, 0.05 pct Fe, 0.002 pct Pb, and 0.002 pct Ni. 8-manganesea is the allo-tropic form of manganese which was present in the cell at temperatures used in this investigation. The manganese carbide, Mn,Ca, was made in the following way: In a closed graphite cell manganese powder was added to graphite powder, which was made from graphite rods for spectrographic use. The manganese powder was the same as that described previously; 5 pct excess graphite was added over that required for the formation of Mn7C,. The mixture was heated in a closed graphite cell for approximately 20 hr at 1350°K under vacuum. X-ray analysis revealed that there was no manganese present after this treatment, but that the lines due to Mn,C, were present. In order to prove that there was no volatile carbide of manganese which was effusing out of the cell, the following experiment was performed: A graphite effusion cell containing graphite power, in excess of that to form Mn,C, of a desired amount, was brought to constant weight on heating at 1228°K. The required amount of manganese was accurately weighed and then added to the graphite effusion cell. The cell was placed in a vacuum at 1228°K for one week, which was the time calculated for the manganese to have effused completely, assuming instantaneous formation of Mn,C8. The cell was then weighed again. This experiment was carried out on two different occasions and both times the weight loss of the cell came within 1 pct of the weight of manganese originally charged minus the weight of manganese left in the cell, as determined by chemical analysis. These data are summarized in Table I. This agreement is considered to be within experimental error and is taken as proof that no carbide of manganese is volatile in this temperature range. It was established, by X-ray analysis, that Mn,C, formed before appreciable amounts of manganese vaporized from the metal powder which was charged. The identification of the carbide of manganese which was present in the Knudsen cell in equilibrium with graphite and manganese vapor was carried out by Kehsin Kuo at the University of Uppsala. He established that the authors' sample, which was submitted to him for analysis, contained the phase

Jan 1, 1958

By L. C. WYMAN

THIS paper discusses what mining reports should contain when presented to the California State Corporation Department, to accompany applications for the sale of stock to the general public, but the principles involved apply to mine financing everywhere. Such reports should 'be as clear and concise as possible, endeavoring to tell the truth in as few words as necessary. Should the engineer be aware that his report is to be used in connection with the sale of stock to the general public, he should consider the public as his client as well as the person who actually employs him. It is always required that the engineer be favorably known and of recognized standing. The following points should be given careful attention : 1. A legal description and location of the property. 2. Transportation conditions, and how they may be expected to affect the operating costs. 3. A brief history of the property, its production record as to tonnage, grade, and character of the ore should be given. Should the property have suspended operations for any reason, this should be given. Any details of former operating costs should be given, especially as to how any improvement could be made, due to better methods which might be employed.' 4. The main geological features and whether they are such as to lead the engineer to believe that the mine may possibly 'be exhausted or the ore of such grade as to be no longer profitable. If he considers them favorable, he should give his reasons for the belief that further development work may produce profitable results. A map showing these features should be submitted, and it is not necessary that such map be highly colored or contain any more than the essential matters. 5. Other mines in the district, or those with similar

Jan 1, 1929

By L. E. Young

GERMANY'S recent collapse and the occupation by the Allies of the coal fields of the Ruhr, the Saar, Silesia, Poland, and Czechoslovakia have focused attention on the postwar coal problems of Europe. American coal operators are interested deeply in what is happening in Britain, particularly in the discussion of plans to rehabilitate and reorganize the entire British coal mining industry, as such reorganization will probably determine the place Britain will occupy in the European coal markets for the next few decades. The continuing decline of British out-ut per man-shift, particularly during wartime, has resulted in a most serious effort to determine whether this unfortunate trend is due to the physical condition of the coal seams, poor management, poor engineering and planning, inadequate use of power and machinery, or failure of labor to co-operate with management.

Jan 1, 1945

By D. P. Pope, T. Vreeland

Observations of dislocations in zinc using Berg-Barrett X-ray micrography confirm the validity of a dislocation etch for (1010) surfaces. A technique for measurement of the depth in which dislocations can be imaged in X-ray micrographs is given. This depth on (0001) surfaces of zinc was found to be 2.5 µ using a (1013) reflection and CoKa radiation. BUCHANAN and Reed-Hill (B & RH) have recently questioned the ability of a dislocation etch to reveal all of the basal dislocations which intersect (1010) surfaces in annealed zinc crystals.' This etch was developed by Brandt, Adams, and Vreeland who conducted a number of different experiments to check its ability to reveal dislocations.2,3 B & RH prepared (0001) foil specimens for transmission electron microscopy from annealed crystals and observed dislocation densities of about l08 cm per cu cm in the foils, while the etch indicated densities of the order of l04 cm per cu cm in their annealed crystals. As this etch has been used in a number of studies of dislocations in zinc, it is of considerable importance to reassess its validity in the light of the B & RH results. The X-ray work reported here was undertaken to check the ability of the etch to reveal dislocation intersections on (1070) surfaces of zinc. The X-ray technique was chosen for this check because it could be applied to the as-grown crystals with a relatively small amount of specimen preparation. We believe that the possibility of accidental deformation in preparation of the bulk specimens is considerably less than that for thin foil specimens suitable for transmission electron microscopy. Unfortunately, basal dislocations are not visible on Berg-Barrett topo-graphs of (1010) surfaces, which are the surfaces on which the etch is most effective. Therefore, a one-to-one correspondence between the etch and X-ray observations could not be made. Basal dislocations near (0001) surfaces have been observed by Schultz and Armstrong4 using the Berg-Barrett technique, but they did not report the as-grown dislocation density observed in their crystals. We have applied the X-ray technique in this study to surfaces oriented from 1 to 2 deg of the (0001) to determine the basal dislocation density, and have compared this density with that observed using the etch on a (1070) plane of the same crystal. The X-ray observations permit determination of the depth in which basal dislocations can be observed under the diffracting conditions used. SPECIMEN PREPARATION High purity zinc crystals are very soft, so a good deal of care must be exercised in the preparation of observation surfaces. As-grown crystals approximately 2.5 cm in diam and 20 cm long were acid cut into 1.25 cm cubes. A thin slab was cleaved from an (0001) surface to produce an accurately oriented reference surface on the specimen. Some of the cubes were examined in the as-machined condition while some were annealed in argon at 410°C for 2 hr. Heating and cooling rates were less than 2°C per min. Some of the specimens were scratched on a (0001) surface with a razor blade to produce fresh dislocations. Approximately 2 mm of material was acid lapped from one face of a cube to produce a surface oriented between 1 and 2 deg from the basal plane and parallel to the [1210] direction. A (1070) surface was also acid lapped. The lap used a 1 to 3 pct solution of HN03 in water to saturate a soft cloth which was backed by a stainless steel plate. The cloth was moved over the crystal surface at a rate of 20 cm per sec while a normal force of about 4 g was maintained between the cloth and the specimen. As-lapped surfaces were examined as were surfaces which were chemically and electrolytically polished after lapping. The small angle between a lapped surface and the (0001) plane was measured to 0.1 deg using a Unitron microgoniometer microscope (the cleaved surface was used as a reference in this measurement). The microscope was modified so that the intensity of reflected light could be continuously monitored on a meter. This modification produced nearly a ten-fold increase in the reproduceability of orientation readings. OBSERVATIONS The Unitron Microgoniometer observations indicated that the lapped surfaces had a terraced structure with the terraces quite rounded and spaced about 0.1 mm in the [1010] direction. The maximum change in slope between terraces was 0.25 deg, indicating a terrace height of about 0.1 µ. A Unitron measurement of the average angle between (0001) and a lapped surface was checked by micrometer measurement of the specimen and found to agree within 0.1 deg. The Berg-Barrett micrographs using (1013) reflections and CoKa radiation5 revealed subboundaries, short dislocation segments, spirals, and loops near the surfaces which were oriented from 1 to 2 deg of the (0001). Micrographs of surfaces prepared by lapping appeared very similar to those of the chemically and electrolytically polished surfaces. The loops and spirals were not extinct in (1013) or (0002) reflections, indicating that they have a nonbasal Burgers vector. Extinctions of the short, straight dislocations indicated that they belonged to an (0001)(1210) system. Fig. 1 is an example of a micrograph which shows a subboundary, and dislocation segments which are pre-

Jan 1, 1970

By P. R. Sperry, A. P. Beck

It has been shown1 that in poly-crystalline strips of high purity aluminum with a fairly random orientation distribution, grain growth progresses gradually until the average grain diameter reaches a value approximately equal to the strip thickness. Recent work at this laboratory led to the realization that grain growth might be impeded to a considerable extent in the presence of a sharply defined texture, where orientation differences between neighboring grains are small. In order to investigate this effect the following experiment was carried out with the same lot of high purity aluminum previously used for grain growth studies in randomly oriented material.' Very large grain size was developed by grain growth at 650°C in specimens of 0.200 in. thickness. These specimens were then rolled to a thickness of 0.050 in. or 1.25 mm—a reduction of 75 pct. In the rolled strip each large grain corresponded to an elongated area easily identified by etching. After annealing for 1 to 25 min at 600°C and re-etching, these elongated areas were again recognizable. Within each area, corresponding to a single large grain before annealing, there formed by recrystallization a multitude of new grains with a fairly well developed preferred orientation. The orientation and the size of the new grains formed in areas corresponding to different large grains, varied widely depending on the orientation of the parent grains with respect to the rolling direction and the plane of rolling. Many areas were found where the average grain size was considerably smaller than the specimen thickness. Such an area occurred in a specimen cut in half before annealing. One half, containing a portion of the area in question, was annealed 1 min at 600°C, the other half, with the remaining portion of this area, for 25 min at the same tempera-Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

By Arthur A. Center

AT the beginning of 1944 it was expected that the production of metallic zinc in the United States from domestic and foreign concentrates would exceed the 1943 figure though domestic production of concentrates was expected to drop below the 1943 rate, mostly in the Tri-State area. Imports of concentrates were estimated to more than take care of such deficiency. North American concentrate production, available for import to the United States or elsewhere during the year, was estimated at over 200,000 tons recoverable zinc content; South American at about 65,000 tons; Australian at about 50,000 tons. Production of both concentrates and metal in the United States, however, did drop, attributable in considerable part to man-power shortage in the industry. However production exceeded consumption, which fell off, and stocks of metal increased. These stocks have increased since the middle of 1942 but production and consumption are coming nearer to a balance. The A, B, and C premiums, which have played an important part in keeping up domestic production of concentrates, extend only to the middle of 1945 by present legislation. Congress is being asked for their continuance during the war and

Jan 1, 1945

By Arthur Crowfoot

INTRODUCTION The principal object of this paper is to present data on the development of the revolving convex round table as a concentrator for the through 0.07-mm. slimes from the ores of the Butte district, although same brief notes on the earliest recorded use of this type of concentrating table in the ore-dressing plants of the Lake Superior region and of the Butte district are also presented. The revolving convex round table belongs to the class of concentrating tables known as film-sizing tables, these tables using the relative transporting power of a film, or thin sheet of water, as it flows over a quiet inclined surface, to separate the minerals of a sorted product.

Jan 8, 1914

NEW MEMBERS The following list comprises the names of those-persons who became members during the month of January, 1914. Members ADIASSEWICH, ALEXANDER, Dept. of Commerce & Industry, 11, Nadejdinskaia, St. Petersburg, Russia. BEARD, JOHN W., Mine Supt., Lane-Rincon Mines, Inca, Temascaltepec, Mex., Mexico; BORCHERDT, WALTER 0., Supt The Bertha Mineral Co., Austinville, Va BREWSTER, BURT B., Sales Engr., Sullivan Machinery Co., 1127 Central National Bank Bldg., St. Louis, Mo: CHASE, ROGER E., JR., Assayer 3906 No. Baltimore St., Tacoma, Wash. CULBERT, J. VICTOR 7S4 Wellington St., London, Ont., Canada; DICKINSON, ALBERT W., Supt. Of Mines Bevier, MO. DODSON, T. M Mores, Colliery, Schuylkill Co., Pa FORREST, CHARLES N., Chem. Engr Maurer, N. J.

Jan 2, 1914

By W. A. Hustrulid, N. A. Ross

An analysis of the design of medium to hard rock tunneling machines is presented. The developed equations are used to compare performances and machine requirements using kerf and fixed pick cutters to bore a given rock. With the use of pick cutters, required thrusts can be greatly reduced and still achieve the same boring rate as with present day tooth or kerf cutters. It appears that the cutting coefficient, which for most boring machines is of the order of 0.1, should be increased to one or larger to facilitate rock removal by cutting rather than grinding. The depth of cut and the indexing distance should be greatly increased to make use of inherent rock weakness.

Jan 1, 1971

By H. C. Theuerer

EVEN the highest purity silicon available for semiconductor use contains significant amounts of donors and acceptors, usually aluminum, phosphorus, and boron. Aluminum and phosphorus can be removed from silicon by adaptations of the zone refining techniques' widely used with germanium. Removal of boron, however, has been a difficult problem. The approximate distribution coefficient for boron in silicon is 0.8, so that while zone refining is possible, it is not very effective in any reasonable number of passes. It has been found, however, that boron can be effectively removed from silicon by treatment of a liquid zone with hydrogen and water vapor. Starting with 40 ohm-cm, n-type silicon, use of zone refining coupled with hydrogen

Jan 1, 1957

[Abrahamson, Guy C., (5'43) 1st Lt., A.C., 0-880861, Base Weather Sta., Fairfeld-Suisun AAB, Suisun, Calif. Adam, Howard Wilbur, (S'46) 45 Eaton Ave., Woburn, Mass. Aguilar, Ruperto G., (S'43) Texas College of Mines, El Paso, Texas. Ainge, Ronald Farra, (S'43) Otago University, Dunedin, New Zealand. Albala, Américo, (S'44) Casilla 4106, Santiago, Chile. Albrecht, Theodore J„ (S'42) Pfc., Co. F, Syme Hall, Rm. 1, SCU 3421, ASTP, N. C. State College, Raleigh, N. C. Aldridge, E. E., Jr., (S'39) Box 58, Eagle Pass, Texas. Alfred, Robert M., (S'40) 25 South St., Brighton, Mass. Allan, Douglas H. W., (S'40) 460 Main St., E., Hamilton. Ont.. Canada.]

Jan 1, 1946

By H. L. Teicliman, E. M. Sipprelle

ENACTMENT of Public Law 290 by the 78th Congress authorized the U. S. Department of the Interior, Bureau of Mines, to conduct an experimental program to develop the technology for obtaining oil from oil shale. In adopting and later extending this legislation, the Congress recognized the impending necessity of supplementing ground petroleum reserves with synthetic fuels. Under the provisions of this legislation, the Bureau of Mines, among other things, was charged with the responsibility of developing mining techniques, methods, and equipment for mining the oil shales of the Green River formation of Colorado, Utah, and Wyoming.

Jan 1, 1950