Search Documents

By A. S. Odeh

The mechanism of two-phase flow in porous media has been a subject of wide controversy. One of the properties essential for understanding the dynamic behavior of two-phase flow is relalive permeability. Relative permeability to a certain phase is defined as the ratio of the effective permeability of that phase to its permeability when it is the only fluid present and powing. In this research, a theoretical analysis was made to determine the effect of viscosity ratio between the non-wetting and the wetting phase on relative permeability. Experimental work was conducted to test the validity of the derived equations. The experiment was conducted on four natural cores. Four oils were used as the non-wetting phases with a viscosity range of 0.42 to 71.30 cp and two wetting phases with a viscosity range of 0.86 to 0.96 cp. Oil and bring were made to flow simultaneously at various ratios, and relative permeability curves were constructed. A total of eight relative pertileability cycles representing eight viscosity ratios were run oil each sample. It was found that relative permeability to the non-~cletting phase varies with viscosity ratio. The relative effect of this variation on relative permeability values was a function of the sample's single-phase permeability, decreasing with its increase. It was concluded that, for .samples of single-phase permeability over I darcy. the effect of viscosity ratio could be disregarded, and relative permeability would be, in effect, a function of satrtration only. INTRODUCTION Two-phase as well as multiphase flow occurs in many fields of science. This type of flow is of particular interest in petroleum production. The knowledge of relative permeability, which describes the dynamic behavior of two-phasc as well as multiphase flow, is essential for solution of problems arising in that field. Thc relative permeability ot a porous medium to a given phase in multiphase flow. is generally considered to be only a function of the saturation of that phase, independent of the properties of fluids involved and ranging in value from zero to unity. Work by Leverett' and Leverett and Lewis' apparently supports this concept. In his experiments Leverett used a clean, packed unconsolidated sand of high permeability (3.2 to 6.2 darcies) with two phases (water and oil) flowing and a viscosity ratio range of 0.057 to 90.0. His results showed that the wide range of viscosity had practically no effect on relative permeability-saturation relationship. Recently accumulated evidence from work performed by several laboratories and a paper by Nowak and Krueger,2 in which relative permeability to oil of a few core samples in the presence of interstitial water was considerably greater than single-phase permeability to water, cast some doubt on the conclusions reached by Leverett' and subscribed to by a large number of individuals in the oil industry. One explanation advanced to explain this behavior states that it is caused by the variable extent of hydra-tion of clay minerals present in the sand. The greater the water saturation, the greater will be the area of contact between water and clay minerals; therefore, the greater will be the extent of swelling with corresponding reduction in permeability. Yuster4 presents another explanation for the recently accumulated evidence. Utilizing Poiseuille's law, he analyzed concentric flow in a single capillary where the non-wetting phase flows in a cylindrical portion of the capillary and concentric with it. The wetting phase flows in the annulus between the non-wetting phase and the capillary wall. The equations obtained indicate that relative permeability to the non-wetting phase is a function of saturation and viscosity ratio. Although Yuster's equations show that fractional rel-ative permeability to oil could be greater than unity, as was indicated by the data of Nowak and Krueger,1 they failed to present an explanation to the experimental data of early investigators such as Leverett.1 Due to the importance of relative permeability in understanding the flow behavior of petroleum reservoir fluids, this work—theoretical as well as experimental —was undertaken to determine whether relative permeability is a function of saturation only as was concluded by Leverett1 or a function of saturation and viscosity ratio as was theorized by Yuster.4 THEORETICAL ANALYSIS An equation will be derived for the rate of oil flow through a porous medium that is initially filled with water. Based on this equation, an analytic expression for relative permeability will be developed. The porous medium will be assumed to consist of .straight circular capillaries of different radii. It will also be assumed that there are no interconnections among the capillaries and no mass transfer across the oil-water interface. Consider a porous sample initially saturated with a wetting phase (water). As a non-wetting phase (oil) is

By N. Mungan

Laboratory imbibition and displacement experiments were performed using crude oil and cores drilled with water and preserved under anaerobic conditions. The purpose of these tests was to determine reservoir rock wettability and to find out if more oil could be recovered by use of NaOH solution than by conventional waterflooding. The preserved cores were found to be oil-wet. Contrary to work in the literature, these cores changed to water-wet upon contact with air. After exposure to air for a week, the cores yielded more oil by waterflooding than when preserved under exclusion of air. At reservoir temperature of 160F, flooding the preserved cores with 0.5N NaOH solution recovered more oil than an ordinary wa-terflood, and additional oil when following a waterflood. When the caustic solution was used from the beginning, all the extra oil was obtained before breakthrough; when the caustic followed a conventional waterflood, the extra oil was produced in the form of an oil bank ahead of the injected caustic. The increase in oil recovery resulted from wettability reversal. Also, use of caustic reduced the volume of injection required to flood out the cores. At room temperature, however, the caustic solution did not reverse the wettability and gave no additional oil recovery. Cores which had become water-wet by air exposure or caustic flooding were restored to their original oil-wet state when saturated with crude oil and allowed to equcilibrate at reservoir temperature for two weeks. Therefore, in the absence of preserved cores, it may be possible to restore weathered cores to their original wettability for use in laboratory floods. INTRODUCTION Waterflooding has been in use since 1865, and is by far the simplest of secondary recovery methods. Unfortunately, most waterfloods are inefficient in recovering oil, often leaving half or more of the original oil in place un-recovered. The low oil recovery generally results from low sweep efficiency and low displacement efficiency. Consequently, to increase oil recovery by waterflooding, sweep and displacement efficiencies should be improved. Sweep efficiency is primarily affected by reservoir heterogeneities and mobility ratio, while displacement efficiency is affected by the capillary forces between fluids and rock surfaces. For petroleum reservoirs, the capillary forces are expressed in terms of interfacial tension and wettability. If oil recovery is to be improved significantly in water- flooding, the capillary forces holding the oil in the raervoir porous matrix must be reduced or eliminated. One way to reduce capillary forces is to inject commercial surfactants ahead of the injection water into the reservoir. Laboratory tests of this method have shown no promise of an economical process yet, and no increase in oil recovery was obtained in the field trials which have been reported. Work is continuing in many companies to find surface-active agents which, in workable concentrations, can yield substantial added oil recovery. Another way to change capillary forces operating in petroleum reservoirs is by changing the pH of the injected water. Wagner et al.' showed that change in the pH sometimes activates the surface-active materials natural to some crudes and brings about gross wettability change. Since pH alteration can be obtained with cheap chemicals, such as hydrochloric acid or sodium hydroxide, the process shows promise of being economical in a field application. Pan American Oil Corp. reported oil recovery by use of caustic solution from a flooded-out reservoir.' Their test, conducted at a small additional cost, yielded results which were so sufficiently favorable and encouraging that the wettability reversal flood was expanded to portions of the field not previously flooded.13 It is important to bear in mind that changes in the pH of the water not only can reverse wettability but also can lower the interfacial tension between water and crude oil. Reisberg and Doscher4 have studied the pH dependency of the interfacial tension of Venture crude using sodium hydroxide solutions of various concentrations. Their data show that the interfacial tension was lowered from 23.0 to 0.02 dynes/cm by increasing the NaOH concentration from 0.005 to 0.5 per cent by weight. Thus, the use of NaOH may lead to additional oil recovery due to both wettability reversal and lowering of interfacial tension. Whether alteration of pH results in wettability reversal from oil-wet to water-wet and increases oil recovery depends on wetting properties of the reservoir rock and the crude. This necessitates delicate laboratory experiments, with suitable core and fluid samples from a field. Although many investigators have studied wettability reversal floods in the laboratory,1,2,5,6 these studies have been carried out with synthetic porous media, refined laboratory fluids and surface-active chemicals to simulate the process. The study presented in this paper is the first time that wettability reversal by pH alteration has been accomolished in laboratory core floods using carefully preserved natural cores, live crude and with experiments performed at reservoir pressure and temperature.

Jan 1, 1967

By George S. Ansell, John B. Hudson, Stephen A. Koffler

The permeability of hydrogen through the a phase of palladium has been measured by a low pressure permeation technique under conditions such that bulk diffusion was the rate-controlling process. The observed permeability is described by the equation: J = 1.80 x 1O-3 P½exp(-3745)/RT) cc(stp)/sec/cm2/en over a range of hydrogen pressure, P, from 2.9 x 10-5 m Hg to 5.0 x 10-3 cm Hg, and over a temperature range, T, from 300" to 709°K. The fact that the permeability shows a square root dependence on pressure and a reciprocal dependence on thickness was taken as evidence that bulk diffusion, rather than surface reactions, was the rate-controlling process. The permeability data were used in conjunction with the solubility data of Salmon et al., to determine the diffusivity of hydrogen through palludium as: D = 4.94 x 10-3 exp(-5745/RT) cm2/sec There was no influence of sub structural defects observed over the temperature range employed. From the permeability data obtained, coupled with grain size measurements, it was concluded that the ratio of grain boundary diffusivity to bulk diffusivity was less than 105 over the range of temperature investigated. THE diffusive mass transport of hydrogen in the a phase of palladium has been studied previously by numerous investigators.' In spite of the large amount of attention this system has received, there is not good agreement between the results obtained in different investigations.' This is due in part to the fact that the mass transport was surface-limited during some of these studies, rather than being diffusion-controlled3-5 The reason for the disagreement in other cases is not clear. These studies made use of such techniques as rate of absorption from solutions6 and gases,' electrochemical potential,8 time lag,' and permeation10,11 to determine the mass transport behavior. Of these, the gas permeability technique is the only method which allows an easy test to determine if diffusion is the rate-controlling mechanism, thus eliminating the uncertainty regarding the limiting transport processes inherent in the other techniques. The two most recent permeability studies are those of Toda10 and Davis." Toda determined the permeability of hydrogen in the a phase of palladium over the temperature range from 170" to 290°C, and over the pressure range from 36 to 630 mm Hg utilizing a steady-state gas-permeability technique. Toda's result was: J = 1.41 x 10-3 P½ exp(-3220/RT) where J = specific permeability in cc(stp)/sec/cm2/cm, P½ = square root of the inlet pressure in (cm Hg)½, R = Universal gas constant, and T = temperature in deg Kelvin. Davis11 also employed a steady-state gas-permeability technique over the temperature range from 200" to 700°C and over the pressure range from 0.02 to 760 mm Hg. His result for the permeability of hydrogen in the a phase of palladium was: J = 3.15 x 10-3 P½ exp(-A440/RT) In the range of overlapping temperature for these two investigations, the values of the specific permeability calculated from the above two equations differ by a factor of about 1.8. In the present investigation, the permeation of hydrogen in the a phase of palladium was determined over a wide temperature range, 27" to 436oC, and over the pressure range from 2.9 x 10-5 to 5.0 x 10-3 cm Hg. This temperature range overlaps that of the previous investigations of Toda and Davis, but also covers the lower temperature range which has never before been investigated. The lower pressure range used here avoided the interaction between the dissolved hydrogen atoms observed at higher hydrogen concentrations.' MATERIALS The as-received palladium specimens were cold rolled from a casting and were supplied as 5.08 cm discs of 0.508 and 0.762 mm thickness. According to J. Bishop and Company specifications, the composition of the discs was 99.95 pct Pd, the balance being Cu, Ag, Au, and Ir. In order to obtain samples of varying grain size, the as-received discs were then heat treated. Sample 1 was treated for eight minutes in a nitrogen atmosphere at 810°C and then air-cooled. Sample D was heated first to 550°C in helium. The helium atmosphere was then immediately replaced by hydrogen and the temperature was slowly raised to 1220°C and held for 22 hr. The sample was then cooled to 550°C where the hydrogen was replaced by helium and the disc was further furnace-cooled to room temperature. Sample H was given the same heat treatment, only with hydrogen substituted for helium below 550°C. The reason that hydrogen was not used throughout the entire annealing cycle for samples D and H was to prevent the distortion encountered by low-temperature cycling in hydrogen observed by Darling." After these heat treatments were completed, the

Jan 1, 1970

By O. Mellgren, A. M. Gaudin, P. L. De Bruyn

The adsorption density of ethyl xanthate on pyrite was determined as a function of xanthate concentration. Surface preparation of the mineral appears to have asafunctionsome effect on the subsequent adsorption process, A monolayer of xanthate on the surface is exceeded only in presence of oxygen. The effect of OH- , HS- (and x and CN- S=)and on the amount of xanthate adsorbed was investigated. Competition between OH- and X- (xanthate) ions for specific adsorption sites is indicated over a wide pH range. IN the flotation of sulfide ores, xanthates are most commonly used to prepare the surface of the mineral to be floated so that attachment to air takes place. The quantity of agent required to make the mineral hydrophobic is usually very small, of the order of 0.1 to 0.25 lb per ton of mineral. Details of the mechanism of pyrite collection are for the most part unsettled. Adsorption of collector has long been believed to involve an ion exchange mechanism as demonstrated for galena' and for chalcocite.2 In the work on chal-cocite it was also demonstrated that a film of xanthate radicals unleachable in solvents that dissolve alkali xanthates, copper xanthate, or dixanthogen was formed at the surface of the mineral. The unleachable product increased with increasing addition of xanthate up to a maximum corresponding to an oriented monolayer of xanthate radicals. Pyrite is extremely floatable with xanthate if its surface is fresh.9 ut the floatability decreases rapidly as oxide coatings increase in abundance. Pyrite shows zero contact angle when in contact with ethyl xanthate solution at pH higher than about 10.5;4 at neutrality, a contact angle of 60" is obtained at a reagent concentration of 25 mg per liter. Alkali sulfides and cyanides are pyrite depressants. In this study of pyrite collection the writers have sought to relate measured xanthate adsorption to the method used in preparing pyrite, to the presence or absence of oxygen, to concentration of hydroxyl, hydrosulfide, sulfide, and cyanide ions. The principal experimental tool has been radioanalysis," " using xanthatcx marked with sulfur 35. Experimental Materials Pyrite: Unlike most sulfides, pyrite is a poly-sulfide. The structure given by Bragg7 resembles that of sodium chloride, the iron atoms corresponding to the position of sodium and pairs of sulfur atoms corresponding to the position of chlorine. The edge of the unit cell in pyrite is 5.40 A and in halite 5.63 A. The S-S distance in pyrite is 2.10 A; the Fe-S distance, 3.50 A: and the Fe-Fe distance, 3.82 A. Natural pyrite from Park City, Utah, was used in this investigation. Pyrite 1 was obtained by hand picking pure crystals. Pyrite 2 and Pyrite 3 were obtained from finer textured crystalline material containing inclusions of silicates. The same cleaning technique was utilized for the preparation of Pyrite 2 and Pyrite 3, whereas a different cleaning technique was used for Pyrite 1. Pyrite 1 was prepared as follows: The crystals were ground in a porcelain ball mill and the 200/400 mesh fraction was separated by wet screening with distilled water, followed by washing for 1 hr with deoxygenated distilled water acidified with sulfuric acid to pH 1.5. The acid was removed by rinsing with deoxygenated distilled water on a filter until a pH of 6.0 was reached in the effluent. This filtration was carried out under nitrogen. The sample was then dried in a desiccator under nitrogen. The period of time for which this pyrite sample was in contact with water containing oxygen was about 4 hr. The specific surface as determined by the BET gas adsorption method was 582 cm2 per g. Final material assayed 53.12 pct sulfur and 46.5 pct iron (theoretical, for FeS,: S, 53.45 pct; Fe, 46.55 pct). After crushing, Pyrite 2 and Pyrite 3 were washed with 1 M HCl. rinsed, and fed to a laboratory shakinq table to remove the small amount of silicates. The concentrate obtained was ground in a laboratory steel ball mill. The 200/400 mesh fraction was separated by classification in a Richards hindered settling tube. This fraction was then given a final wash with 0.1 M HCl and deoxygenated water was filtered through the sample. The final effluent showed a conductivity equivalent to that of a solution having a salt concentration of 0.3 ppm. Aqueous hydrogen sulfide solution was then added to the sampln (about 100 ml saturated H,S solution to about 1000 g pyrite under a few hundred milliliters of water) which was stored wet under nitrogen. The sample stored in this manner showed no indication of formation of iron oxides, whereas iron oxides appeared

Jan 1, 1957

By S. N. Singh, M. C. Flemings

Results are presented of a detailed study on the combined influences of ingot dendrite am spacing and thermomechanical treatments on the structure and solution kinetics of high --purity cast and worked 7075 alloy. Solution kinetics were found to depend sensitively on ingot dendrite am spacing and on details of therrnomechanical processing, including amount of reduction and extent of&apos; solution treatment before reduction. An approximate analysis is given for rate of solution of nonequilibrium second phase in the cast and worked structres; results of the analysis are compared with experiment. MICROSEGREGATION in high strength aluminum alloys manifests itself as "coring" (composition differences within the primary aluminum-rich phase), and as interdendritic second phase. The mechanism of formation of the microsegregation is understood, and approximate prediction of the amount of second phase is possible for simple binary systems.1,2 When alloy elements or impurities are present in amounts less than their solid solubility at solution temperature, any phases forming from these elements are termed "nonequilibrium" and can be dissolved by appropriate solution treatment. The rate at which the nonequilibrium phases are removed depends sensitively on their spacing (dendrite arm spacing in the cast material, or band spacing in wrought material). When alloy elements or impurities are present in amounts in excess of their solubility at the solution temperature, second phase particles form an "equilibrium" second phase that does not dissolve in heat treatment and may, in fact, coarsen in such treatment. Usual commercial, high strength, wrought aluminum alloys contain nonequilibrium second phases that were not fully dissolved during ingot processing. They also contain equilibrium second phases resulting from impurities present in amounts greater than their solubility. As has been shown by Antes, Lipson, and Rosenthal,3 and will be demonstrated further in a subsequent paper by the authors,4 significant improvements in mechanical properties of high strength alloys can be achieved by reduction or elimination of these second phases. Methods of elimination are 1) to employ high purity materials to minimize amounts of equilibrium second phase, and 2) to employ suitable thermomechanical processing techniques to fully eliminate nonequilibrium second phases. Work reported herein comprises a study of selected thermomechani- cal processing treatments, and of their influence on solution kinetics of wrought high purity 7075 alloy. EXPERIMENTAL PROCEDURE Melting and Casting. The bulk of the work reported was performed on a single ingot of high purity 7075 alloy. The ingot was 4 in. by 4 in. by 8 in. high, uni-directionally solidified following a procedure previously described.5 The mold was heated to 1350°F before pouring the melt. The bottom chill was carbon coated stainless steel. Water was circulated through the chill after the melt was poured. The 7075 alloy was prepared from high purity virgin material (aluminum, zinc, magnesium) and from master alloys (Al-50 pct Cu, A1-15 pct Cr, A1-5 pct Ti). Final measured melt composition (wt pct) was: Zn Mg Cu Cr Ti Fe Si Al 5.70 2.28 1.35 0.18 0.15 <0.002 <0.012 bal Melting was done in a silicon carbide crucible; all tools were coated with zircon wash to minimize iron contamination; degassing was by bubbling chlorine through the melt. che-rmomechanical Treatments. Detailed studies were made on material taken from a location approximately 13 in. from the chill and 51/2 in. from the chill (i.e., from 1 in. thick slices taken between 1 and 2 in. from the chill and between 5 and 6 in. from the chill). Solution treatment was done at 860°F in an air-circulating furnace with a "bottom drop" arrangement to achieve minimum delay time between solution treatment and quench. Samples solution treated in this way were 2 in. by 2 in. by 1 in. Temperature of the quench water was approximately 10°C. Mechanical reduction was by cold rolling. Samples 11/2 and 51/2 in. from the chill were treated for 12 and 24 hr, respectively, before cold rolling. Reduction by cold rolling was then 4/1, 16/1, and 35/1. In each case, several intermediate anneals (1/2 hr at 860°F) were used to permit reaching the final thickness without cracking; two such anneals were used for the 4/1 reduction, five for 16/1, and six for 35/1. After working, materials were again solution treated for various lengths of time from 0 to 48 hr and quenched in water. Structural Measurements. Secondary dendrite arm spacings were measured using procedures previously described.&apos; For each measurement reported, five photomicrographs were first made at X75. Measurements were made of dendrite arm spacings in at least 20 different grains (grain structure was equiaxed). Grain size measurements were made by running a number of random traverses across photomicrographs of the samples and obtaining the mean lineal intercept. Measurement of the volume percent of second phase and porosity was done by quantitative metallography. A two-dimensional systematic point count was used

Jan 1, 1970

By Jaakko Kajamaa

Neutron diffraction was applied to determine sheet textures by the transmission method. Cold-rolled and recrystallized copper sheets were investigated. The amount of cube texture was determined for three compositions, in which the phosphorus content was, respectively, 0, 0.005, and 0.03 wt pct. The heat treatment was in every case 8 sec at 650°C. In the two latter cases the cube texture was prevented. In addition a comparison with the X-ray diffraction transmission method was made with the 96 pct cold-rolled copper sheet. Outer parts of both (111) pole figures can be considered to be rather identical. This is seen from the fact that the intensity ratio ITD/120" was 0.45 for neutron diffraction and 0.40 for X-ray diffraction. Differences between the methods were discussed in detail. Features peculiar to neutron and X-ray diffraction in texture studies were listed and compared. In this work neutron diffraction was applied to determine sheet textures. Specifically, it was desired to ascertain whether this method can be used to reveal differences when compared to other methods. In addition, the amount of the cube texture in copper sheets was determined as a function of phosphorus content. Previous applications of neutron diffraction to texture problems include the following: nickel wires,&apos; wire of some bcc metals,&apos; and uranium bars.3 In the neutron diffraction technique the greatest difference is in the sample—its method of production and its volume. A sample needs no treatment and its volume is roughly 105 times larger than the volume of an X-ray diffraction sample. The cold-rolled sheet was investigated both by neutron diffraction and by X-ray diffraction, because it is expected that, due to large number of defects, possible differences in the results of the two methods would be revealed. It is a well-known fact that X-ray lines show broadening when cold-worked. Analysis has shown that this is based chiefly on small crystalline size, micro-stresses, and/or faults.4&apos;5 Neutrons are sensitive to the above-mentioned disturbing factors as well, but circumstances in diffraction are different from the X-ray case. Because the sample represents a larger volume, the result is an average over that volume. In addition, it can be assumed that the sample has preserved its original structure, because it needs no special preparation. The particular limitation of neutrons is the relatively low neutron intensity available from nuclear reactors. This decreases the resolution as compared to the X-ray diffraction methods. Furthermore, absorption mainly reduces diffracted X-ray intensity, while multiple scattering effects, i.e., secondary extinction, disturb neutron diffraction. SO neutrons and X-rays behave in a different way when interacting with matter. As in other structural investigations, one can utilize this difference in texture studies as well. One cold-rolled and three recrystallization textures in copper sheets were investigated by neutron diffraction. The samples were produced at the Outokumpu copper factory to the specifications shown in Table I. The paper is divided into five parts. The first deals with the theory of the measurement. In the second, experimental procedures are described. Results are presented in the third part. Both cold-rolled and re-crystallized samples are studied. Discussion is in the fourth part, and finally in the fifth part some conclusions are drawn. 1) THEORETICAL CONSIDERATIONS Properties peculiar to neutron diffraction are the following: a) the scattering length varies greatly between one element and another; b) many of the elements do not absorb neutrons appreciably. In this connection it is of primary interest to know the interaction of neutrons with lattice imperfections. As with X-rays this problem leads to diffraction analysis of deformed and recrystallized metals. From the physical point of view the main difference is that neutrons are scattered by nuclei (magnetic scattering is not considered here), whereas X-rays are scattered by electrons. The features peculiar to neutron and X-ray diffraction methods in texture studies are listed in Table 11. Pole figures are an important tool in performing structural analysis of deformed or recrystallized metal. Present texture research technology requires pole figures which are as precise as possible. The choice between these two methods depends on the technical information which is required. The X-ray diffraction transmission technique may give results which are not necessarily representative of the average physical state of the sample. Although foil samples normally contain enough crystallites for diffraction, they may not necessarily represent the whole structure. An example of this problem is the frequently observed difference between the "surface" and the "inside" texture of a sample. The production of foil samples may disturb the original structure of the parent material. The selection and orientation of the foil from the sample is quite arbitrary. Normally, a highly deformed piece of metal has several texture components. Different components are deformed in a slightly different manner. This is a re-

Jan 1, 1969

By E. T. Turkdogan, P. Grieveson

It is shown experimentally that, by making use of the coupled S-O reaction in ionic melts, it is possible to transfer slclJur or oxygen from a lozv to a high chemical potential through an ionic nzenzbrane. This uphill transfer of sulfur is accompanied by a counter downhill transfer of oxygen and vice versa. The Materials balance shows that the amoulits of sul -fur and oxygen lost or gained by one system are the same as those gained or lost by the other systenz — the two systejns being separated by an iofzic membmne. The systems used in these experi?nents were solid Mn-MnS-Mno and liquid Fe-S-0. Sufficient results were obtained Lo study the kinetics of the transfer and the indications are that the counter diffusion of sulfide and oxide iojzs in the membrane is the rate controlling process. WHEN an ionic oxide-melt reacts with an atmosphere containing sulfur and oxygen-bear ing gases the following reaction occurs: 1/2 S2 (gas) +O2- (melt) = S2- (melt) + 1/2 0, (gas) [1] Under the restrictions that i) electric conductance in the melt is purely ionic and ii) each constituent element in the melt does not change valence, the solution of an atom of sulfur in the melt will result in the evolution of an atom of oxygen, so that the electric neutrality is maintained. For a given temperature and melt composition, the equilibrium concentration of sulfur in the melt is determined by the ratio, po2 /ps2 , in the gas phase and not by the individual partial pressures of oxygen and sulfur. This has been demonstrated by a number of investigators, for example by Richardson and withers&apos;, Fincham and Richardson,la by St Pierre and Chipman,&apos; and by Turkdogan and Darken.3 In his Howe Memorial Lecture for 1961, Darken discussed the possibility of uphill pumping of sulfur through an ionic membrane at the expense of oxygen. TO test the validity of this concept associated with coupled reactions, experiments were carried out in the following manner. A presintered mixture of Mn-MnS-MnO and prefused mixture of Fe-S-0, contained in platinum and iridium crucibles, respectively, and separated by a thin layer of soda-glass (to act as an ionic membrane), were placed side by side in an evacuated silica capsule and sealed. This was then kept at 1400°K for a required time to allow Reaction [11 to occur via the ionic membrane. When partial equilibrium is reached, the ratios Po2 /pS2, for systems on either side of the membrane, are equal and the flux of sulfur and oxygen through the membrane becomes zero, although the individual partial pressures po2 andp,, in these two systems may differ considerably.

Jan 1, 1962

By W. D. Robertson, D. A. Koss, A. J. Goldman

THE significance of the hcp (E) structure, which appears when Fe-Cr-Ni alloys (stainless steels) are transformed martensitically, has been the subject of considerable study and speculation.&apos;-7 It has been proposed that the hcp structure is an intermediate phase in the transformation: fcc (austenite) — hcp (E) -bcc (0, martensite). However, recent studies by transmission electron microscopy6,7 have indicated that the hcp structure may be a consequence of the large shear strain (10 deg) associated with the fcc to bcc transformation. That is, the transformation to a bcc structure is accompanied by extensive dissociation of dislocations in the parent austenite, which has a low stacking-fault energy.&apos;-&apos;&apos; X-ray diffraction analysis of the transformed alloy reveals a pattern of lines corresponding to an hcp structure, together with the parent austenite and the bcc product. The fact that the hcp structure is observed only in association with the bcc product in these alloys1&apos;4&apos;6&apos;7 lends support to the conclusion that the hcp structure is a secondary product of the transformation. But, the evidence is circumstantial and more definite resolution of the two possibilities mains to be obtained. If the hcp structure is an intermediate product of the transformation, as in 1) above, then two distinct Ms temperatures should be observed, Ms and To evaluate this possibility, three different techniques that are particularly sensitive to the structural changes accompanying such transformations have been used in an attempt to detect two transformation temperatures in an Fe-15.1 Cr-11.7 Ni alloy: 1) high-sensitivity differential thermal analysis, 2) the temperature dependence of resonant frequency (elastic moduli), and 3) internal friction of cylindrical specimens vibrating in either longitudinal or torsional modes. To obtain the necessary sensitivity, a differential thermal analysis technique was developed for the purpose, Fig. 1. The differential temperature between a nickel standard and the specimen was amplified to produce a sensitivity of 0.02OC (0.7 v) in temperature difference. The specimen and the standard were surrounded by a copper block and the entire assembly was immersed in a solution of methyl and ethyl alcohol, freezing point, - 140OC, which provided the necessary thermal stability to reduce temperature fluctuations to negligible proportions. A cooling rate of about 1.5OC per min was obtained by bubbling liquid nitrogen through the liquid bath. In order to calibrate the experiment with respect to the evolution of heat in the transformation from fcc to hcp structures, differential cooling curves were obtained for an Fe-19.8 Mn alloy, which transforms martensitically to E.&apos;"-&apos; a Ms(e) temperature of 145°C was clearly defined by a temperature

Jan 1, 1964

By R. L. Featherly, J. R. James

The replacement or reconditioning of oil storage tank bottoms due to external corrosion is an expensive maintenance item to the oil industry. Cathodic protection as a means of mitigating this problem has proved very successful in the past few years. One pipe-line company recently used magnesium anodes to cathodically protect two 55,000 bbl and two 20,000 bbl tanks. The tank bottoms were protected as individual units with considerable factual data being taken on one of the 20,000 bbl tanks. Twelve 60-lb anodes were installed about 2½ ft from the tank on approximately 17-½ft centers around the tank. Previous installations and tests have shown that sufficient protection is provided when the tank-to-soil potential using a copper-copper sulphate half-cell as a reference electrode is — 0.90 volts at the edge of tank. Potential measurements taken a few months after completing the installation indicated that the potentials were higher than were needed for protection. Resistors were then inserted in the individual anode circuits which increased the life of the anode installation and still provided adequate protection for the structure. All connecting pipe lines were then insulated from the tank. This limited the anode current strictly to the tank resulting in a greater degree of protection with a still longer anticipated anode installation life. The total installation cost for this tank was less than $300 which amounts to $20 per year The corrosion of metallic structures in contact with soil or water has been a very serious and costly problem for centuries. The annual loss to our nation&apos;s pipelines alone is estimated at $200,000,000. Mitigation of this problem by various methods has been carried on quite successfully for a number of years. An electrical method called cathodic protection has been used with considerable success to control corrosive influences on pipelines, tank bottoms, cable sheathing and other buried metal structures. Corrosion of oil storage tank bottoms has been a serious problem among the oil industries for years. In addition to damage costs and loss of oil, the replacement of one tank alone represents several thousand dollars. A reconditioning program at periodic intervals was instituted by several organizations and found to be a very expensive process. A few years ago two of the pipeline companies installed cathodic protection units at their tank farms.3&apos;4 The average current required for protection of the tank bottoms varied from 0.7 to 1.0 milliampere per square foot. The results indicated that adequate protection was obtained at a cost of approximately 10 pct of the previous reconditioning program. The Republic Pipe Line Company experienced severe corrosion on their oil storage tanks. One of their 55,000-bbl tanks

Jan 1, 1948

By R. L. Featherly, J. R. James

The replacement or reconditioning of oil storage tank bottoms due to external corrosion is an expensive maintenance item to the oil industry. Cathodic protection as a means of mitigating this problem has proved very successful in the past few years. One pipe-line company recently used magnesium anodes to cathodically protect two 55,000 bbl and two 20,000 bbl tanks. The tank bottoms were protected as individual units with considerable factual data being taken on one of the 20,000 bbl tanks. Twelve 60-lb anodes were installed about 2½ ft from the tank on approximately 17-½ft centers around the tank. Previous installations and tests have shown that sufficient protection is provided when the tank-to-soil potential using a copper-copper sulphate half-cell as a reference electrode is — 0.90 volts at the edge of tank. Potential measurements taken a few months after completing the installation indicated that the potentials were higher than were needed for protection. Resistors were then inserted in the individual anode circuits which increased the life of the anode installation and still provided adequate protection for the structure. All connecting pipe lines were then insulated from the tank. This limited the anode current strictly to the tank resulting in a greater degree of protection with a still longer anticipated anode installation life. The total installation cost for this tank was less than $300 which amounts to $20 per year The corrosion of metallic structures in contact with soil or water has been a very serious and costly problem for centuries. The annual loss to our nation&apos;s pipelines alone is estimated at $200,000,000. Mitigation of this problem by various methods has been carried on quite successfully for a number of years. An electrical method called cathodic protection has been used with considerable success to control corrosive influences on pipelines, tank bottoms, cable sheathing and other buried metal structures. Corrosion of oil storage tank bottoms has been a serious problem among the oil industries for years. In addition to damage costs and loss of oil, the replacement of one tank alone represents several thousand dollars. A reconditioning program at periodic intervals was instituted by several organizations and found to be a very expensive process. A few years ago two of the pipeline companies installed cathodic protection units at their tank farms.3&apos;4 The average current required for protection of the tank bottoms varied from 0.7 to 1.0 milliampere per square foot. The results indicated that adequate protection was obtained at a cost of approximately 10 pct of the previous reconditioning program. The Republic Pipe Line Company experienced severe corrosion on their oil storage tanks. One of their 55,000-bbl tanks

Jan 1, 1948

By Marsh S. Watson, Robert A. Howard

The effect of depth of formation penetration by casing perforations has been studied by means of an electrolytic model. It is found that the relative productivity of perforated casing is profoundly affected by the depth to which the formation is penetrated. The first in. of penetration i: of especial importance. A scaling equation which was shown to agree with experimental results at zero penetration is used to calculate the relative productivity of a waled down casing with scaled down perforations. INTRODUCTION In an earlier piper&apos; the authors showed that the point sink representation of casing perforations is inade- quate. It was Pointed out at that time that while the electrolytic model results were a marked improvement over point-sink calculations, they still left a great deal to be desired in that the electrolytic model represented a case not realizable in practice, namely, a clean hole through the casing but undisturbed formation on the other side of the casing. Obviously, to be effective, the perforation must penetrate a finite distance into the producing formation. It was the purpose of the present investigation to find how the relative productivity of perforated casing varies with depth of penetration. The term "depth of penetration" as used in this paper refers to the distance which the perforation penetrates the producing formation. The amount of casing and cement penetrated is not taken into account, a fact which is discussed more fully later. The "casing radius," therefore, is to be interpreted as the radius of the boundary between cement and formation wall. in cases where the casing is not in contact with the formation wall. APPARATUS The electrolytic model experimental setup was identical with that described in the previous paper&apos; except that the platinum electrodes were now allowed to project from the lucite cylinder by varying amounts. When fewer than eight electrodes were used, the unused ones were covered with a coat of insulating material to minimize disturbances to the current flow-lines. Comparison runs made with the unused electrodes uninsulated, however, showed that the values of Q/Q0 so obtained did not vary by more than the experimental error from the values obtained with the unused electrodes insulated RESULTS The variation of relative productivity* with perforation density is shown for various penetration depths from 0 to 4.03 in. in Fig. 1. It will be seen that even one in. of penetration into the formation results in a huge increase in the relative productivity. Moreover, as-the depth of penetration increases, it becomes less and less advantageous to use large perforation densities, 80 pel. cent of open hole productivity being obtained with only three 0.5-in. diameter holes per foot when the penetration is 4.03 in.

Jan 1, 1950

By W. D. Forgeng, B. F. Decker

IT has been known for almost a century&apos; that silicon and nitrogen combine when heated to a high temperature. Three nitrides have been reported, SiN, Si3N,, and Si,N, containing 33.3, 40.0 and 42.9 pct nitrogen by weight, respectively. The existence of SisN, is well established but that of Si,N, and SiN is doubtful. The first systematic study of the reaction between silicon and nitrogen was made in 1910 by Weiss and Engelhart" who determined the rate at which silicon absorbed nitrogen at temperatures from 1250°C to

Jan 1, 1959

By H. B. Hunter, F. G. Stone, F. J. Dunkerley

Introduction and Literature Survey This is the second in a series of papers coming from this laboratory on the correlation of the low temperature tensile properties of tin-binary alloys with microstructure. These engineering data and those of the previous paper1 were obtained as the initial part of a long-range program to determine the changes in the fundamental mechanical properties accompanying the beta to alpha phase change in tin and its binary alloys below 13.2°C. Since it appears now that the more fundamental studies will be delayed,* and since no summary of the low temperature properties of these tin-base white bearing alloys was found in the literature, it was decided to publish all the engineering data thus far obtained. Accordingly, the tensile properties of thirteen binary alloys containing from 0.1 to 60 pet cadmium and 0.1 to 10.43 pet antimony measured at six temperatures from —196 to +23°C are presented here and their variations rationalized in terms of microstructure. A literature search showed that these systems had not been investigated at low temperatures, although both the tin-cadmium and tin-antimony2,3,4,5 and the tin-rich corner of the ternary system67 have been studied at room temperature. Hanson and Pell-Wal-pole5 and Homer and Plummer4 determined the tensile properties of alloys containing from 0 to 10 pet cadmium. The same authors3 determined the tensile strength and elongation in the tin-antimony system from 2 to 18 pet antimony at room temperature while Pell-Walpole et al.6,7 studied the properties of high tin and tin-antimony-cadmium alloys. Since there were many variables besides composition in these tests, it was difficult to make a valid comparison with the room temperature data of the present study, but in general the tensile strength and ductility values are in reasonable agreement. Pell-Walpole2 also determined the effect of grain size on the tensile strength of pure tin and 1 pet alloys of both antimony and cadmium. The true maximum stress was found to decrease exponentially as the number of grains in the cross-section increased. This effect of grain size was strikingly revealed in the present work, as indicated in a later section. Hanson and Pell-Walpole8 placed the solid solubility limit of antimony in tin at 3.5 pet at 20°C, increasing to 4 pet at 190°C, and then sharply increasing to 10.3 pet at 246°C (the latter being a peritectic point). Their results are in disagreement with those of previous investigators,9 and the discrepancy seems to lie in the micro-graphic observation of the second phase

Jan 1, 1950

By Gordon A. Gross

Banded siliceous manganese-iron bearing sediments recognized as distinctive facies of Algoma-type iron formation constitute low-grade resources of manganese in many countries. Manganiferous facies associated with oxide and carbonate facies of iron formation have iron to manganese ratios ranging from 0.2 to 2 and commonly about one. Manganiferous facies up to 30 m thick occurring separately or with other iron formation facies are associated with cherts, carbonates, shales, turbidites, tuffs, and lavas. Primary cherty manganiferous facies and their gondite metamorphic equivalents represent significant manganese resources and are protores for higher-grade deposits derived by secondary enrichment processes.

Jan 1, 1983

By Phillip Philbin, Frank E. Senftle

A field neutron activation analysis technique suitable for determining uranium in ores has been tested. The method is based on the measurement of the 74.7 keV gamma ray from &apos;U. When the thorium/uranium ratio is greater than one or the vanadium is greater than 1%, a low uranium analysis is obtained. No satisfactory correction for thorium has been found, but a correction for vanadium can be deter¬mined. For ore containing greater than 0.01% uranium, the uranium can be deter¬mined with an accuracy of about 10% which is quite adequate for a field exploration technique.

Jan 1, 1972

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

Dispersion-containing titanium-copper alloys were prepared having mean free paths varying from 1.0 to 9.7 P. Tensile studies at room temperature and at 1000°F showed that little or no strengthening occurred when the mean free path exceeded 3 p. However, at lower values of mean free path appreczable strengthening was observed. A considerable amount of strengthening also resulted from copper in solid solution. DURING the past several years, an increasing amount of study has been devoted to dispersion hardening, an alloying process in which increased strength is obtained through the addition of a ran-

Jan 1, 1961

By W. C. Hazen, A. V. Henrickson

URANIUM plant operations of the Kerr-McGee Oil Industries at Shiprock, N. M., began in December 1954. As originally designed, the plant treated Plateau carnotite ores by the acid cure process, which dissolved both uranium and vanadium minerals. After 16 hr of acid curing, the ore was conveyed to an agitator and leached for 2 hr in acid liquor at a pH of 1.0. The leach pulp was then separated at 100 mesh in a classifier, the sands continuing through a washing classifier circuit and the slimes going to a countercurrent decantation system of four thickeners.

Jan 9, 1957

By William E. Ford, Edward Salisbury Dana

1. Normal Class (28) Gypsum Type 2. Hemimorphic Class (29) Tartaric Acid Type 3. Clinohedral Class (30) Clinohedrite Type Mathematical Relations of the Monoclinic System Crystallographic Axes. - The monoetinic system includes all the forms which are referred to three unequal axes, having one of their axial inclinations oblique. The axes are designated as follows : the inclined or clino-axis is a; the ortho-axis is b, the vertical axis is c. The acute angle between the axes a and c is represented by the letter 0; the angles between a and b and b and c are right angles. See Fig. 331.

Jan 1, 1922

By D. P. Seraphim

Single crystals of bee Li-Mg solid solution were grown and their internal friction was measured as a function of temperature, A peak of the Zener type was found in the damping spectrum. The activation energy for the relaxation process is 21.5 ± 1 kcal per mole and the frequency factor is 1015.7 ± 0.7 sec-1. ZENER internal-friction peaks which are observed for a wide range of solid solutions are attributed to stress-induced changes in local order.&apos; In the present work a Zener internal-friction peak, the first reported for a solid solution of an alkali metal, is

Jan 1, 1961

By N. A. D. Parlee, M. T. Utine

ThE kinetics of absorption of oxygen by induction-stirred liquid silver (at constant Po2 and T) has received some study here.&apos;&apos;2 This paper describes a study of the kinetics of effusion (non-bubble-forming), and some additional work on absorption. A Sieverts type of apparatus was used. The kind of reaction tube assembly has been described.4 The same 25-kw, 450-kc induction unit was used as in earlier absorption work1&apos;2 but the "coupling" was different. The runs were made under the following conditions: i) saturation at 1 atm, effusion at 0.81 atm;

Jan 1, 1969