Search Documents

By Carlos G. Valenzuela

The value generally accepted for stacking-fault energy, of copper has been approximately 40 ergs per sq cm based on Fullman's2 value for the coherent twin-boundary energy and the assumption that is twice the twin boundary energy However, Thornton and coworkers8 determined that the lower limit of for copper is approximately 60 ergs per sq cm, based on measurements of dislocation-node radii. They suggested that the assumption of = 2t is invalid. It is the purpose of this note to present results which indicate that the values of obtained by measurement of twin-grain boundary intersections and the values obtained by measurement of dislocation-node radii are actually compatible. The most reliable values for of the a brasses, based on electron-microscope observation of dislocation nodes, are probably those values reported by Smallman and Green6 who applied the Siems correction (1961) to data obtained by Howie and Swann.3 These values shown in Fig. 1 give an extrapolated value of approximately 70 ergs per sq cm for pure copper. In the present work, Fullman's method for determining the stacking-fault energy of copper was extended to the a brasses. High-purity copper (99.999 pet) and high-purity zinc (99.999 pet) were mixed in proportioned amounts and melted in sealed and evacuated quartz tubes. The alloys were homogenized for a week at 750°C and chemically analyzed by means of X-ray fluorescence. These alloys, along with a specimen of pure copper, were rolled to 98 pet reduction and a thickness of 0.009 in., resealed, and annealed for 40 hr at 715°C. Values for the ratio of twin-boundary energy to the grain-boundary energy, it gb, were obtained from measurements of dihedral angles formed at the intersections of twin boundaries and grain boundaries by using Fullman's2 mechanical analogy of surface tensions acting at the intersection of an annealing twin and a grain boundary. The angles between the twin traces and the grain boundaries were measured for a large number of twin-grain boundary intersections at a magnification of X500 using a rotating mechanical stage on a Reichert metallograph. The rotary stage has a calibrated angle scale with vernier so that measurements can be made to 0.1 deg. The mean twin-grain boundary energy and standard deviation were calculated for copper and each of the brasses by the use of an IBM 7072 computer. It was found that the mean value of gb stabilized after approximately 100 twin-angle measurements. This was determined by plotting the mean against the number of angles measured. Since the measured angles deviate from true dihedral angles, a correction factor for grain orientation, discussed below, was applied. The stacking-fault energy was then calculated from these values and the values of grain-boundary energy derived by Taylor.7 The data obtained are tabulated in Table I. Values for stacking-fault energy are plotted in Fig. 1. The value of gb for the specimen of 1.03 pet Zn is close to the value obtained by Fullman2 for OFHC (99.98 pet) copper, 0.045. It is believed that the purity of the copper affects gb significantly. The 99.999 pet purity Cu used in this investigation yielded a value of yt/ygb, 0.76, which is much higher than that obtained by Fullman. Additional evidence suggesting that the purity of

Jan 1, 1965

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2'4'5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.' Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

By A. M. Gaudin, C. S. Chang

Adsorption was measured for barium ion and laurate radical, using radioactively marked agents, over wide range of concentrations. Laurate adsorbed in absence of barium fails to float. With barium, flotation-effective laurate coating needs not exceed 5 pct of monolayer. Barium adsorption then is several fold larger. No barium laurate coating is obtained. IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.'-' The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods."-" In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba" to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,' were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand-picked quartz, washed free of stains, were reduced in size to —20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This —200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.' The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74-micron quartz particles, using a surface factor of 1.96; is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1953

By A. M. Gaudin, C. S. Chang

Adsorption was measured for barium ion and laurate radical, using radioactively marked agents, over wide range of concentrations. Laurate adsorbed in absence of barium fails to float. With barium, flotation-effective laurate coating needs not exceed 5 pct of monolayer. Barium adsorption then is several fold larger. No barium laurate coating is obtained. IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.'-' The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods."-" In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba" to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,' were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand-picked quartz, washed free of stains, were reduced in size to —20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This —200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.' The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74-micron quartz particles, using a surface factor of 1.96; is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1953

By P. R. Swann, J. G. Parr

Quenched structures were studied in alloys containing up to 12.5 pct cobalt. The subsequent decomposition of a 10 pct cobalt retained-ß phase alloy was investigated using metallographic and X-ray diffraction methods. Hardness measurements also were made during the decomposition process. Precipitation of Ti2Co is by nucleation and growth; and an activation energy of 50,000 cal per mole was determined. The values of the coefficient ß suggest that the precipitate is pearlitic at temperatures between 450 and 475°C, and spheroidal between 500 and 525°C. THIS paper describes part of a series of invesligations into phase transformations in binary alloys of titanium with transition elements. The general approach is similar to that taken in work on titanium-iron and titanium-nickel alloys.' Previous investigators'' have established the titanium-rich end of the titanium-cobalt phase diagram, reproduced in Fig. 1. Orrell and Fontana' showed that alloys containing more than about 6 pct" cobalt quenched from the ß range, produced 100 pcl retained-p phase. The isothermal decomposition of alloys containing between 0.8 pct Co and 15.5 pct CO was investigated by the same workers in the temperature range 650 to 1000°C. They reported that these alloys transformed into a or Ti,Co depending on the cobalt content, but no quantitative data were given. In the work to be described a series of alloys containing 0.8 pct Co to 12.5 pct Co was examined in the quenched condition. The 10 pct Co alloy (the lowest cobalt content to retain 100 pct ß on quenching) was selected for further work on the tempering kinetics of the ß decomposition. Experimental Procedure Since our own melting equipment was not installed at the outset of this work, the Physical Metallurgy Division of the Department of Mines and Technical Surveys (Ottawa, Canada) prepared the alloys. These were made of Japanese sponge, (which when melted had a value of 103 DPH, using a 1-kg load), and electrolytically prepared cobalt. The al- loys, made up to contain 0.8, 1.6, 3.3, 5.8, 8.3, 10.0 and 12.5 pct Co, were homogenized by swaging into rods at 900°C. Filings were taken from the rods, and any iron chips from the file were separated magnetically. Size fractions of both plus and minus 200 mesh (about 75p) were shown by their constitution, after annealing just below the eutectoid temperature, to contain the same cobalt content. Consequently, it was permissible to use the —200-mesh fraction, knowing it to be representative of the rod composition. Quenching in argon was carried out in a newly designed furnace, whose features include (1) an Inconel furnace tube, (2) a positive pressure of argon maintained at all times in the furnace—even when a sample is removed or inserted. The furnace is shown in Fig. 2 and is described in the Appendix. The tempering processes were carried out on powder samples sealed in evacuated quartz capsules. Since the highest tempering temperature was 525OC, no protection against reaction with the quartz was necessary. (Tests were made on filings of iodide titanium and showed no hardness increase after equivalent heat-treatments.) A thermocouple was attached to the capsule, which was heated to the

Jan 1, 1959

By G. F. Sager, B. J. Nelson

Magnesium alloy forgings offer higher and more uniform mechanical properties than heat treated magnesium alloy castings and are used principally for light weight parts that may be stressed in fatigue or subject to impact loads, or where space limitations do not permit the use of the necessarily bulkier magnesium alloy castings. Compositions and Properties of Magnesium Forging Alloys The nominal compositions and properties of the principal commercial magnesium forging alloys are given in Table 1. The two that are most commonly used are AMC58S and AM65S. The former has the highest strength and is, therefore, employed for heavy duty applications. However, the forging of this alloy and of AMC57S ordinarily requires the use of slow speed hydraulic presses. The forging alloy AM65S combines good, although somewhat lower, mechanical properties with excellent forging characteristics. This alloy can be forged on hammers, upsetters, rolls, and mechanical presses, as well as on hydraulic presses. These characteristics make it particularly useful for many applications. Manganese Segregation in AM65S The alloy AM65S contains 5 pct tin, 3 1/2 pct aluminum, and a small amount of manganese, the manganese being added to insure satisfactory resistance to corrosion. Some manganese segregation was occasionally encountered in this alloy. In many applications, such segregation is of no particular consequence, but when forgings are acid dipped prior to the application of various chemical coatings, the segregated particles of manganese constituent may stand in relief. The resultant surface roughening may impair appearance and is undesirable in forgings employed in the textile industry, where very smooth surfaces are essential to avoid the catching and breaking of fine threads. An effort was therefore made to determine the cause of manganese segregation in this alloy and find a method for its elimination. Radiographic examination of a series of cast ingot sections and extruded samples of the AM65S type having manganese contents ranging from zero to about 0.7 pct revealed no appreciable manganese segregation when the manganese was less than about 0.4 pct. A small amount was observed with a manganese content of 0.46 pct and considerable with manganese contents of 0.6 pct or higher. Attempts to eliminate the manganese segregation by variations in the melting and casting conditions were unsuccessful and it soon became apparent that the trouble was attributable to the fact that the manganese contents that caused segregation were in excess of the amounts that would remain in solution at temperatures encountered in the melting and/or casting operations prior to the complete solidification of the ingots. A knowledge of the amounts of manganese that would be soluble in molten alloys of the AM65S type at various temperatures was obviously desirable. The liquid solubilities of manganese in binary Mg-Mn alloys and in Mg-Al-Mn and Mg-Zn-Mn alloys have been determined by Tiner and others,* but no data on the solubility of manganese in molten magnesium alloys containing tin and aluminum are given in the literature. For this reason, an investigation to determine the solubility of manganese in a magnesium alloy containing 5 pct tin and 3.5 pct aluminum (AM65S type) was undertaken.

Jan 1, 1950

By Irving B. Cadoff, Ernest Levine

The fracture path in a Cu-4 pct Ag alloy wet with mercury was found to he dependent on the heat treatment used prior to tensile testing. Both quenched and slow-cooled alloys were embrittled by the mercury.. For quenched alloys, which were single -phase, the crack path was intergranular. Slowly cooled alloys, which contained precipitate platelets, exhibited transgranular fracture. By comparing stress-strain data for these alloys with similar data on mercury -embyittled solid-solution alloys, it was found that the role of the precipitate and that of the grain boundary in the fracture process were equivalent . THE fracture path which results when metals are strained in a liquid environment appears to be dependent upon the nature of the specific system. Mixed transgranular and intergranular cracking has been observed in the 2024 T4 aluminum alloy when wet with a Hg-Zn amalgam.' Transgranular fracture was induced in an A1-4 pct Cu alloy by masking off the grain boundaries from the liquid Hg-Zn amalgam.' The embrittlement of solid-solution alloys of copper in mercury results in intergranular fracture.' The effect of a precipitated phase on the fracture path in copper alloys is the subject of the present investigation. Cu-4 pct Ag was chosen so that its behavior could be compared with previous work on embrittlement of copper alloys. PROCEDURE High-purity copper (99.999 pct) was used as a base metal, along with 99.999 pct purity silver. Melting was carried out in graphite crucibles with manual agitation to get adequate mixing. The ingots were homogenized by means of vacuum annealing, chemically cleaned, and cold-rolled with intermediate vacuum anneals, to the desired thickness of 0.025 in. The rolled sheets were sheared to the final specimen size of 1 by 0.025 by 0.1 in. The specimens were then electropolished in phosphoric acid (concentrated) and heat-treated in an evacuated capsule at the solution temperature of 770°C. One batch was slow-cooled and the other quenched in water. The thermal etching which occurred during heat treatment was sufficient to permit grain boundary and precipitate delineation. Tensile tests were carried out in air and in mercury on a Table-Model Instron at a pulling speed of 0.2 in. per min. Wetting was accomplished by electro-polishing in phosphoric acid, rinsing in alcohol, and immersing in a pool of mercury. Once wet the coating was stable throughout the mechanical tests. In our studies it was found that wetting the surface or total immersion in mercury produced identical results. For convenience, the wetting technique was used for the experiments described. The crack pattern was observed directly on the surface by removing the mercury after testing. De-wetting was accomplished by flame heating the samples in a vacuum after testing and before observation of the surface. No etchant or polishing was used so as not to obscure the crack pattern on the surface. The mercury removal, however, resulted in a pitted surface but otherwise left the pertinent features visible. Photomicrographs were taken in this condition so as not to disturb the structure associated with the crack pattern. The average precipitate spacing was measured previous to coating the sample with mercury by use of an optical eyepiece micrometer. RESULTS The microstructure of the quenched specimens was single-phase while that of the slow-cooled specimens contained thin platelets of a second

Jan 1, 1964

By Donald E. Grimes

In conjunction with Inland Steel&apos;s development of lead-bearing steels possessing improved machin-ability because of tellurium and/or selenium additions, it was decided to determine liquidus and solidus temperatures in the Pb-PbTe-PbSe sub-ternary system. With the exception of alloys in the PbTe-PbSe system, it is believed that no previous study of this subternary has been performed. Thermal analysis was employed in a general survey of the subternary. In addition to PbTe, PbSe, and pure lead, ten ternary compositions were selected at intervals of ten at. pct. Sixty-gram alloys were prepared by sealing an appropriate mixture of the elements in quartz crucibles with a central thermocouple-well under a vacuum of less than 10 p. All three elements were 99.999+ pct pure with only trace impurities detected by spectroscopic examination. After the alloys had been heated at least 20°C above the liquidus in a Kanthal furnace, cooling and heating curves were obtained. Two or more cooling curves were employed both for the determination of each alloy liquidus and for the solidus of those al- loys containing greater than 50 at. pct Pb. Cooling rates were 0.5° to 3.5°C per min during the 5 min immediately prior to the start or end of solidification. For those ternary alloys containing 50 at. pct Pb, the solidus was determined from heating curves. Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple which was calibrated in the same apparatus against the freezing points of zinc (A. D. MacKay—99.999 pct), antimony (A. D. MacKay-99.999 pct), and copper (ASARCO—99.999+ pct) both before and after the experimentation. The only interruptions in the continuous strip-chart recording of the temperature occurred for brief periods at significant points of interest when direct readings were made with a Rubicon Type B potentiometer sensitive to * 1 µv. The average liquidus and solidus temperatures obtained in this investigation are listed in Table I together with probable errors based on the accuracy of the thermocouple calibration and the reproduci-bility of the data. No chemical analyses of the alloys were performed because the synthetic or as-charged compositions were felt to be reliable. The melting points obtained for PbTe (924.7° ± 0.7°C) and PbSe (1084.0° ± 0.6°C) compare favorably with recent findings of other investigators.&apos;-&apos; As indicated in Table I, both the liquidus and solidus temperatures increase as selenium replaces tellurium for a constant atomic percent lead. As a result, the ternary liquidus and solidus temperatures for a given percent lead lie between the corresponding binary temperatures published in the literature. It should be noted that those ternary alloys containing 50 at. pct Pb exhibit a relatively narrow liquid-plus-solid region (<80°C) when compared with alloys containing greater than 50 at. pct Pb. Alloys with 60, 70, or 80 at. pct Pb not only have a much wider liquid-plus-solid region (>500°C) but also exhibit considerably lower and approximately constant solidus temperatures which thus form a virtually isothermal solidus "plane" slightly below the melting point of pure lead (327.3°C). For these alloys

Jan 1, 1965

By R. A. Swalin, L. A. Neimark

The research work presented in this paper had initially a two-fold goal. First, further data concerning the low-temperature recovery of cold work was desired. Recovery phenomena have been extensively studied in face-centered-cubic metals but at the time of initiation of this research, no investigation concerning the low-temperature recovery in body-centered-cubic metals had been made. During the course of the investigation a paper by Martin on the recovery of point defects in molybdenum appeared.&apos; Comparison of our results on tungsten with Martin&apos;s results on molybdenum will be made. Secondly, knowledge concerning the influence of a particular type of impurity addition on the recovery kinetics was desired. It has been known for a long time that extremely small amounts of certain impurity additions exert a profound influence on the recrystallization behavior and the resulting microstructure of tungsten. Small amounts of potassium silicate and aluminum chloride added prior to the reduction of tungsten oxide to the metal have been found by Smithells to raise the recrystallization temperature markedly,2 and yield an ultimate microstructure in which grains several millimeters long are produced in fine wires of say 10 mil diam. If the impurities are added singly, ordinary secondary recrystallization results with none of the spectacular properties of the wire to which special additions were made. Swalin and Geisler3 and Rieck4 have studied the recrystallization behavior of such doped wire in some detail. The former workers found that small amounts of these impurities raised the recrystallization temperature over 400°C and electron microscopic examination revealed no obvious inclusions in the microstructures. In fact. chemical analysis showed that there was <0.001 pct K, <0.002 pct Al, trace of Si, and <0.0003 pct 0 in the wire studied. The possibility that the role of the special impurities is to keep the structure open by void formation and that submicroscopic porosity acts as the inhibiting agent has been discussed.2&apos;3 Meijering and Rieck5 have suggested that the impurities are strung out as second-phase particles in a direction parallel to the drawing direction. It was thought that a kinetic study of recovery could perhaps elucidate the role of the impurities to some extent. When a metal is deformed by cold work three basic types of defects are thought to be introduced into the crystal lattice, namely, interstitials, vacancies, and dislocations. Van Bueren6 has proposed that recovery of cold-worked metal is a four-stage process, each step being the result of the annealing of a primary defect or a combination of defects and having a unique activation energy. The steps in order of increasing activation energy are attributed to a) the diffusion of interstitials recombining with vacancies, b) diffusion of vacancy pairs, c) the diffusion of single vacancies, and d) climb of dislocations. In metals with relatively low- or medium-range melting points the temperatures for recovery are low enough so that the first three steps may occur during room-temperature deformation. For tungsten, because of the high melting point and subsequently high recovery temperature, it was calculated, using Nowick&apos;s approach7 that this recovery would occur in the temperature range 200" to 600°C. It is also known that recovery of X-ray line broadening, presumably due to dislocation climb, occurs at about 600°C.8 EXPERIMENTAL METHOD Two types of cold-rolled 10-mil-diam tungsten wire were used in the investigation; a) pure tungsten, (called undoped) and b) G. E. No. 218 wire (called

Jan 1, 1961

By L. A. Roe, John Jan

Iodine is a soft, lustrous, grayish-black nonmetallic element with a density of 4.9. It is the least active of the four members of the halogen family. The other members are, in order of increasing activity, bromine, chlorine, and fluorine. Iodine is a solid at ordinary temperatures, while bromine is a liquid and chlorine and fluorine are gases. Iodine melts at 113°C and volatilizes at 184.4°C to a blue-violet gas with an irritating odor. It occurs in nature only as iodates and iodides or other combined forms. It was discovered by Bernard Courtois in France in 1811, who noticed its presence as an unknown substance in crude soda ash obtained from burning seaweed. Gay-Lussac recognized it as a new element and named it iode, from the Greek word "ioeides or iodes" for violet color (MacMillan, 1970). The world production is not known with any great certainty, but it is probably between 25 and 35 million lb per year, of which about 30% is consumed in the United States. Geology and Mineralogy Iodine compounds occur as a minor constituent as a mineral in the Chilean nitrate deposits and in solution in brines and seawater. According to the US Geological Survey, it is the 47th most abundant element in the earth&apos;s crust. The minerals lautarite, Ca (I03)3 (calcium iodate), and dietzeite, Cat (103)2 (CrO4), (calcium iodate-chromate) are found in Chilean nitrate deposits which are located in Antofagasta and Tarapaca provinces on the eastern slope of the coast range in a desert area. Various brines contain iodine compounds. Seawater contains about 0.05 ppm of iodine and some seaweeds will extract and accumulate it up to 0.45% on a dry basis. Some coals in West Germany also contain iodine compounds. The known and potential sources of iodine reported in 1968 are given in Table 1. Table 2 lists estimated world iodine reserves. Iodine has been recovered from brines in Java, Indonesia, France, England, and the USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. The indicated reserves and future resources of iodine are large but have never been adequately measured. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable. Markets and Prices Iodine and its compounds are generally marketed in the form of: iodine, crude; iodine, resublimed; calcium iodates; calcium iodide; potassium iodide, sodium iodide, and numerous organic compounds. Product Specifications Crude iodine, World market: 99-99.5% 12. Crude iodine, US produced, average: 99.8% 12. Crude iodine, USP XVII Specs: not less than 99.8% percent I2. Resublimed iodine is usually 99.9% and ACS specifications call for not over 0.005% total bromine and 0.020% nonvolatile materials (Anon., 1971). Prices, c.i.f. United States, for iodine have been steadily increasing from $1.18 per lb of crude in 1967 to $6.37-7.27 in January 1981 (Anon., 1981). In 1980 the price of iodine increased by 50%.

Jan 1, 1983

By Jean-Jacques Prompsy, J. S. Rinehart

The purpose of the present study was to arrive at a better understanding of the stress fields developed within drill bits under dynamic loading and the influence that these stress fields could have on the failure of the drill bits. Particular emphasis has been given to the influence that bit shape has on the establishment of highly localized, potentially destructive stress inhomogeneities within the bit. This paper covers one phase of a broad study involving three velocity regimes: impacts at very low velocities, 0 to 20 ft/sec, a velocity range in which dynamic effects are just beginning to be found; impacts at velocities ranging from 20 to several hundred ft/sec, arange commonly encountered in practical drilling operations; and impulsive loading through the detonation of explosives, a velocity range in which the dynamic effects are greatly exaggerated and made more identifiable. Specifically, fracturing which develops at the end of a cylindrical bar undergoing a shock produced by impact was experimentally investigated, the impacted area being the face of a truncated cone terminating the cylindrical bar. Fracture characteristics were looked at as a function of impact velocity, area of impacted face and cone angle — parameters of considerable importance in the design of drill bit. EXPERIMENTS The specimens were made of Plexiglas, which enabled the fracture pattern to be easily observed. In Plexiglas, the velocity of a longitudinal wave is about 8,700 ft/sec, and the velocity of the transverse wave about 4,200 ft/sec. The specimens were impacted by a steel cylinder whose lower face was parallel to the terminal face of the experimental bit, as shown in Fig. 1. The impacting mass was shifted up and down on two steel rods, dropping from a maximum height of 11 ft, with the velocity varied between 0 and 6.5 m/sec. The initial mass of the cylinder was 4.1 kg, which could be increased by steps up to 8.8 kg by addition of steel plates. The velocity of the steel cylinder was determined by using an electric circuit; as the cylinder dropped, it contacted two steel wires, the first one starting and the second one stopping an electronic counter. Two similar counters connected in parallel were used to corroborate each other. The velocity was checked at each drop as it had been observed to vary somewhat from drop to drop. The two contact wires were located just above the top of the specimen so as to give a value of the instantaneous velocity of the steel cylinder at impact. The distance between the wires was 40 ± 0.5 mm and the discrepancy between the counters was never more than 0.1 m/sec. Thus the velocity was known to within 3.25 per cent. This precision was sufficient with respect to the precision of the machining of the specimens. A very small lack of parallelism between the face of a specimen and that of the impacting hammer resulted in an oblique impact which required a much lower velocity to break the specimen. The experiments had a twofold purpose — (1) to observe the fracture pattern, and (2) to find relationships between the minimum velocity required to generate a fracture within a specimen and the

By E. D. Gardner, E. M. Sipprelle

The Synthetic Liquid Fuels Act (58 Stat., 190; 30 U.S.C. Sup., Secs. 321-325) was approved by Congress April 5, 1944; it directed the Bureau of Mines to build demonstration plants to produce synthetic liquid fuels from coal, oil shale, and agricultural products. The most important oil-shale deposits in the United States are in the Green River formation of Colorado, Utah, and Wyoming. The oil shale of western Colorado generally is more amenable to exploitation, more persistent, and apparently richer than elsewhere in the Rocky Mountain Region. It occurs at the top of a high plateau surrounded by bold, nearly vertical escarpments 500 to 600 ft in height. The top 400 to 500 ft of these escarpments comprises an oil-shale measure that averages 15 gal of shale oil per ton; the bottom 70 90 100 ft of the measure, called the Mahogany Ledge, averages over 30 gal per ton. The full measure in a 1000-square-mile area is estimated to contain 300 billion barrels of shale oil;&apos; the Mahogany Ledge is estimated to contain 100 billion barrels of oil. These estimates are based on numerous surfac,e samples and on core-drill holes drilled by the Government and by private enterprise. The oil-shale beds are undisturbed and lie nearly horizontal. The name "oil shale" is unfortunate, as the rock is a tough, strong marlstone. Organic matter named "kerogen" is a constituent of the rock. The oil-shale demonstration mine is on Naval Oil-Shale Reserve No. 1; it is about 5 1/2miles by mountain road from the plant site, which, in turn, is 2 miles from U.S. Highway 6 and 10 miles west from Rifle, Colo. The highway parallels the Colorado River, the Denver and Rio Grande Western Railroad, and a 66,000-volt public-utility power line. Early in the program it was realized that an oil-shale enterprise would have to be on a large scale to be commercial, and that unusually low mining costs would be necessary. The physical characteristics of the Mahogany Ledge and an overlying roof stone are unusually favorable both for large-scale operation and low mining costs. Quarry practices largely will be followed underground to mine the Mahogany Ledge. The aim has been toward complete mechanization of all mining operations. A mining unit would comprise a square mile containing 100,000,000 tons of oil shale with allowance for mining losses. An investment of $1,000,000 would be $0.01 a ton; such an expenditure, therefore, could be made to save, say, $0.015 per ton daily operating cost. A goal of a mining cost of $0.50 per ton was set up in 1945. Open-cut mining costs then were about $0.25 per ton of material handled; it was hoped that a cost double this amount could be obtained in mining the Mahogany Ledge. Costs of labor and supplies have increased since 1945 and so has the selling price of petroleum products. To those unacquainted with the character of the Green River deposits, the name "shale" suggested high mining costs. Others assumed that coalmining costs of $2 to $5 per ton would apply. To many, the expected mining costs appeared the principal handicap to the establishment of an oil-shale industry. The purpose of the Bureau of Mines is to demonstrate methods and to establish costs for mining the oil shale on a large scale. It is hoped this work will lead to the establishment of a large-scale, commercial oil-shale enterprise.

Jan 1, 1950

By A. W. Demmler

RECENTLY, Chaudron,&apos; Montariol,2 and their co-workers published the results of their studies on zone-refined aluminum. They found their material to be capable of recrystallization at —50°C, but gave no data as to the percentage reduction or time required. Their material was found to be practically non-work hardening at room temperature, but after 96 pct cold work at a low temperature and storage in liquid nitrogen it was found to recrystallize to coarse grains in less than 3 hr at 20°C. Recently, a study was made of the room temperature recrystallization characteristics of zone-melted aluminum. An ingot 14 in. in length, with a 3hx3 in. cross section, was made in an extremely high purity graphite boat under an atmosphere of dried commercial argon. It was made by first passing the molten zone along the ingot of 99.99+ pct A1 15 times. At this point, the most impure 3 in. (the end toward which the eutectic forming impurities migrated) were replaced with more of the original starting material, and 15 more traverses were made. Each traverse of the zone along the ingot required approximately 3 hr. Three ingots were prepared in this identical fashion and the chemical analyses were made spec-trographically on two of these ingots, rather than on the one used in this investigation. The analyses were made at 1 in. intervals along the ingot, in duplicate. Over the purest 5 in. of the ingot, which were most important in this investigation, there was found an average composition of <0.00004 pct Cu, <0.0003 pct Fe, <0.0001 pct Si, and <0.0001 pct Mg. In addition, the following elements were not detected spectrographically even in the more impure end of the bar: manganese, zinc, nickel, chromium, titanium, vanadium, lead, tin, boron, beryllium, bismuth, gallium, zirconium, cadmium, antimony, cobalt, and molybdenum. The original ingot was given several cold reductions, with intermediate anneals in order to refine the grains. Owing to the extreme length resulting and the ease of deforming the material plastically, it was cut into eight equal lengths and identified as shown in Fig. 1, with the highest numbered section at the purer end (that enriched with peritectic formers). Section 6 was used in the exploratory work and was found to be of exceptionally high purity, giving more rapid rates of room temperature re crystallization than any previous aluminum studied at the Alcoa Research Laboratories. This fact suggested that the entire midsection of the ingot might be of very high purity. Accordingly, section 4 was chosen for the next study. A portion of it was rolled to cold reductions of 10, 25, 40, 60, 75, and 90 pct at room temperature, and the re-crystallization of each specimen was followed by X-ray pinhole transmission photographs. The other portion received the same treatment, except that both the specimens and the rolls were maintained at 160°F in the process of rolling. The latter ortion was retarded in its recrystallization as compared to the former, probably due to the stress relief effect of the warm rolling. Both of these portions of the fourth section were found to recrystallize at a considerably slower rate than did the sixth section.

Jan 1, 1957

By F. G. Stone

A strain anneal process has been developed for the production of iron tensile test specimens, the gauge length consisting substantially of a single crystal. Since the method has been quite successful and the results of general interest, the process will be described in detail. The essential feature of the method is the continuous, slow increase of furnace temperature during the grain growth annealing treatment. Briefly, the procedure is as follows: I. Heat machined bars to 950°C in vacuum, hold I hr, furnace cool. 2. Strain to 3.5-3.8 pct elongation (axial loading). 3. Anneal, continuously raising furnace temperature from 450 to goo°C at a rate of so0 per day. 4. Hold at 900°C for 100 hr, furnace cool. Tensile test bars with a 1/4- X I-in. gauge section have been machined from 35 in. Armco iron plate and from 3/8 in. rounds of Puron, a high purity laboratory iron. The axes of the test bars were parallel to the rolling direction. During the machining operation the bars were polished in the lathe with No. 600 emery paper, and this polished surface proved satisfactory for subsequent macrographic examination. A micrographic examination of the materials showed that both were high in FeO inclusions, those of the Puron being smaller but much more numerous. An initial vacuum anneal of I hr at 950°C followed by furnace cooling resulted in a ferritic grain size of ASTM No. 3 for Armco and No. I for Puron. Special heat treatments which reversed these initial grain sizes produced no marked improvement in single crystal production after subsequent treatments. The strain for subsequent grain growth was determined by measuring the decrease in diameter of the tensile bar during elongation. The change in diameter could be measured with a micrometer to +0.0001 in., corresponding to an accuracy of 0.08 pct for the elongation. The accuracy of the diameter measurement is also dependent on grain size because of surface roughening during elongation, and for this reason, a No. 3 grain size is preferable. Optimum grain growth was obtained for strains between 3.5 and 3.8 pct elongation. Once this critical range had been cstablished, all tests were held within it, and thus only meager data were obtained on grain growth following strains outside this range. In general, grain size decreased with increasing strain to about 5.5 pct elongation. Grain growth was occasionally ohserved with less than 3.5 pct elongation although this may have been the result of error in measurement. The program control device for the grain growth anneal consisted of a I rpm motor and worm gear drive, operating the dial shaft of a pyrometer controller through a pulley. Dial speeds of 33 and 50°C per day were tried, but the results at the slower speed were not sufficiently better to warrant the increased furnace time. The furnace tube was evacuated at intervals during the run and kept sealed the remainder of the time. When the controller reached 900°C, it was stopped and the temperature held for 100 hr. This eliminated most of the numerous minute crystallites of about 0.5 mm dimension usually visible on the etched surface of the single crystal. Since recrystallization occurs at the A3 point, the top temperature of 900°C provided a 10"

Jan 1, 1949

By W. H. Triplett

DISCUSSION John G. Barry (Mexico)—"The Nerinea limestone," writes W. H. Triplett, p. 584, "is ... medium-bedded (0.5 to 1.0 m)...." This is the Zuloaga formation. It has always been described as thick-bedded (1.0 to 3.0 m). "Whether the marls and shales were less amenable to replacement," he goes on to say, ". . . is a matter of opinion." In general, it is probable that the thinner-bedded formations were less competent than the nearby thicker-bedded, so that the latter produced pre-mineral breccias when all were subjected to flexing stresses. With reference to Mr. Triplett&apos;s analysis, p. 584, under Lower Cretaceous, in the Taraises and Cupido formations some few horizons should be considered as possibly containing hidden orebodies. In the Potrero camp, shown on the general map in the northwestern part of Fig. 4, p. 587, several mineralized beds are known; they are found throughout the whole thickness of the Cuesta del Cura formation. With regard to intrusive rocks, p. 585, the general map, Fig. 4, shows that the Potrero and Noche Buena camps are near a third, monzonitic intrusive. It seems doubtful that the Aranzazu was any hotter than the Providencia camp. However, the former does contain large deposits of exogenetic silicates, which in large part occur within the Zuloaga limestone, as shown by Bergeats in a stereogram. At the Aranzazti camp the La Caja formation was only slightly changed, whereas it was altered highly at the Providencia, possibly en-dogenetically. That the temperatures at the Providencia camp were relatively high at one time is also shown by the tourmaline veinlets and lenses in the monzonite and by the garnets on Temeroso peak; high temperature mineralization has possibly been eroded. Maps and sections show that the Concepcion del Oro —Temeroso stock occupies the original locus of some 40 kms of sedimentary rocks. The remains of large roof pendants at Carmen and Animas indicate that stoping was active. Whether all the sedimentaries were stoped and assimilated presents a lively problem, a correlative of which would be an estimate of the original constitution of the invading instrusive rock. As to extrusive rocks, see p. 585, there is also a large thick area of the extrusives left near Noche Buena in the "La Caja" intramontane valley of the La Caja range. This place gave its name to the range. The volcanics are also said to occur in considerable amount in the Mazapil valley.&apos;&apos; Turning now to the remarks under Regional Structure, p. 586, as partly indicated on the general map, Fig. 4, the Mazapil Mountains of the Mazapil region are a continuous, U-shaped range including a northern leg of some 24 km, a southern leg of similar length, and a uniting base which lies to the East and which measures some 10 km in a S 20 E direction. Thus the U-shaped mountains are continuous through a length of 58 km and also contain one continuous anticline, the adjacent valleys being synclinal. The northern leg of the U is called the La Caja range, the base is called the Concepcion del Oro range, and the southern leg the Santa Rosa range. The ranges in northeastern Zacatecas and southern Coahuila contain anticlines and the valleys contain synclines, which where thin are necessarily highly compressed isoclines with very steep dips. Many of the anticlines also have isoclinal components which are overturned, original mushroom tops being indicated. The anticline in the base of the U of the Mazapil Region, Concepcion del Oro range, is a recumbent anticline, over to the ENE, with a necessarily subjacent recumbent syncline.

Jan 1, 1953

By W. H. Triplett

DISCUSSION John G. Barry (Mexico)—"The Nerinea limestone," writes W. H. Triplett, p. 584, "is ... medium-bedded (0.5 to 1.0 m)...." This is the Zuloaga formation. It has always been described as thick-bedded (1.0 to 3.0 m). "Whether the marls and shales were less amenable to replacement," he goes on to say, ". . . is a matter of opinion." In general, it is probable that the thinner-bedded formations were less competent than the nearby thicker-bedded, so that the latter produced pre-mineral breccias when all were subjected to flexing stresses. With reference to Mr. Triplett&apos;s analysis, p. 584, under Lower Cretaceous, in the Taraises and Cupido formations some few horizons should be considered as possibly containing hidden orebodies. In the Potrero camp, shown on the general map in the northwestern part of Fig. 4, p. 587, several mineralized beds are known; they are found throughout the whole thickness of the Cuesta del Cura formation. With regard to intrusive rocks, p. 585, the general map, Fig. 4, shows that the Potrero and Noche Buena camps are near a third, monzonitic intrusive. It seems doubtful that the Aranzazu was any hotter than the Providencia camp. However, the former does contain large deposits of exogenetic silicates, which in large part occur within the Zuloaga limestone, as shown by Bergeats in a stereogram. At the Aranzazti camp the La Caja formation was only slightly changed, whereas it was altered highly at the Providencia, possibly en-dogenetically. That the temperatures at the Providencia camp were relatively high at one time is also shown by the tourmaline veinlets and lenses in the monzonite and by the garnets on Temeroso peak; high temperature mineralization has possibly been eroded. Maps and sections show that the Concepcion del Oro —Temeroso stock occupies the original locus of some 40 kms of sedimentary rocks. The remains of large roof pendants at Carmen and Animas indicate that stoping was active. Whether all the sedimentaries were stoped and assimilated presents a lively problem, a correlative of which would be an estimate of the original constitution of the invading instrusive rock. As to extrusive rocks, see p. 585, there is also a large thick area of the extrusives left near Noche Buena in the "La Caja" intramontane valley of the La Caja range. This place gave its name to the range. The volcanics are also said to occur in considerable amount in the Mazapil valley.&apos;&apos; Turning now to the remarks under Regional Structure, p. 586, as partly indicated on the general map, Fig. 4, the Mazapil Mountains of the Mazapil region are a continuous, U-shaped range including a northern leg of some 24 km, a southern leg of similar length, and a uniting base which lies to the East and which measures some 10 km in a S 20 E direction. Thus the U-shaped mountains are continuous through a length of 58 km and also contain one continuous anticline, the adjacent valleys being synclinal. The northern leg of the U is called the La Caja range, the base is called the Concepcion del Oro range, and the southern leg the Santa Rosa range. The ranges in northeastern Zacatecas and southern Coahuila contain anticlines and the valleys contain synclines, which where thin are necessarily highly compressed isoclines with very steep dips. Many of the anticlines also have isoclinal components which are overturned, original mushroom tops being indicated. The anticline in the base of the U of the Mazapil Region, Concepcion del Oro range, is a recumbent anticline, over to the ENE, with a necessarily subjacent recumbent syncline.

Jan 1, 1953

US 4,181,703-Removal of magnesium impurity from phosphate rock. Crushed screened ore containing more than 0.3% by weight of magnesium is slurried with sea water, acidified with sulfuric acid to a pH value not lower than 2 5, and filtered and washed before the neutralization point is reached. W. Wengeler, F. Wolstein, and E. Hoffman, assigned to Uhde G.m.b.H. Jan. 1, 1980 4 pp (423-167) Filed: 11-18-77 (852,918)

Jan 1, 1982

By Howard W. Jacky

At Weed Heights, Nev., precipitation plays a major role in the plant operation. Almost two-thirds of the present copper production is leach-precipitation plant copper. The entire plant complex processes about 135,000 tons of low grade copper ore per week. Of this tonnage, 49,000 tons of about 0.78% sulfide ore are treated in the concentrator. This is handled in the conventional manner of crushing, grinding, and concentration of the copper sulfide by flotation.

Jan 6, 1967

By P. Ramachandrarao, T. R. Anantharaman

CONSIDERABLE interest has lately been evinced as regards the nature of chill zones in solidified metals and alloys. Biloni and Chalmersl were the first to show through their study of segregation substructures in some nonferrous alloys that the formation of the dendritic region may be preceded by a diffusionless solidification process, viz., predendritic solidification. Subsequently Bower and Flemings2 tried a special solidification technique wherein the liquid was drawn into a narrow copper mold with polished surfaces and concluded that convection might trigger some multiplication mechanism leading to grain refinement. Using uncoated and partially coated surfaces for molds in the Bower-Flemings technique as well as in conventional molds, Biloni and Morando3 have very recently brought out the importance of the rate of heat extraction on the mechanism of solidification. We report here on the surface structures and substructures observed in a Sn-1 wt pct Pb alloy solidified at even higher cooling rates (riz., l05 to l07 ºc per sec) than those employed by earlier workers. The alloy was made by melting tin (99.99+ pct) and lead (99.9+ pct) in a silica tube under vacuum. Small quantities of the homogenized alloy (0.5 to 1.0 g) were then quenched (or splat-cooled) from the melt by the "gun technique" developed by Duwez et al.4 The thickness of the resultant foils varied from specimen to

Jan 1, 1970

By Alan T. Gorton, T. L. Joseph, Gust Bitsianes

High-temperature X-ray diffraction techniques were used to determine thermal expansion coefficients of iron and its oxides. Lattice parameters of a and iron, wiistite, magnetite, hematite, and goethite were determined and plotted as a function of temperature. From these results, the true and mean linear thermal expansion coefficients were calculated. In the case of noncubic crystals, the expansion coefficients were determined along each of the crystallographic axes. The effect of the magnetic transformation on lattice parameter was measured for a iron and magnetite at their respective curie temperatures. COEFFICIENTS of expansion for iron and its oxides were determined from the temperature dependence of their lattice parameters. From these data, the true linear coefficients were derived by means of the formula: at =[(l/ao )(dao/dt)] [1] where at is the true linear coefficient of expansion, a, is the lattice parameter in angstrom units, and all variables are referred to the temperature, t, in OC. Thus the true expansion coefficient represents the instantaneous change in lattice parameter on a unit basis and at a particular temperature. A second expansion coefficient is also often used. It is termed the mean linear coefficient and is defined in the following way: am = [ao(t) - ao(O)]/ao(0) l [21 This coefficient represents the average change in lattice parameter on a unit basis but at a specified parameter length, ao at O°C, and over a specified temperature range,1 to 0°C. Generally the true co-

Jan 1, 1965