Search Documents

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.' The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.'

Jan 1, 1964

By G. H. Alvey, A. W. Foster

The measure of value of an oil property is approximated by the length of time it takes to "pay out;" viz., the time required for it to return the original investment. This time varies in different fields. In the Appalachian and Mid-Continent fields, a good investment pays out in about four years; in California, it requires a slightly longer time; and in the Gulf field about two years. The two principal methods for establishing these values are based on acreage, as in California, and on production, as in the Appalachian field. The method of establishing values based on production1 was worked out in the Appalachian fields and approximates the value remarkably well in some fields; but it is a rule of thumb and should be used intelligently. Briefly, the method is as follows: An arbitrary number of dollars (called the barrel-day price) multiplied by the number of barrels of settled daily production of the property gives the value. In its crudest application, the barrel-day price is determined by the "$10 to $0.01" rule, which means that the barrel-day price is one thousand times the prevailing price of oil. For instance, with oil at $3.50 per bbl. the barrel-day price would be $3500 per bbl. This rule, however, is not strictly applied, for the barrel price is varied according to whether or not the wells "hold up." But when a barrel price for a district has been fixed it is quite general to raise or lower the price with the fluctuation in the price of oil; here the"$10 to $0.0l"ruleisused extensively. However, the prospective purchaser takes into account tangible equipment upon the property, the extent to which the drilling program has been carried out, whether or not the wells are "shot" or natural, depth of wells, spacing of wells, paraffin trouble, etc. The basis of this method is settled production. As soon as production is considered settled, a flat barrel-day price is generally applied to all properties, no matter what their age. If it were possible to show that this flat rate was erroneous and that the value of the property depended on the point on the decline curve at which the wells happened to be (in other words, their age), and also on the operating costs, the future price

Jan 1, 1921

By Harry W. Antes

The density changes that occurred on annealing cold-worked poly crystalline molybdenum, over the temperature range of 870" to 1630 SC, were determined. Increases in density were observed for recovery and the beginning of recrystallization. An initial decrease in density was observed during re-crystallization. A second decrease in density was observed after recrystallization was completed, as the microstructure changed from columnar grains to equiaxed gvains Both decreases in density were associated with an increase in gain boundary area to volume ratio. The second decrease in density was observed in the annealing range that immediately precedes secondary recrystallization as reported in the literature VARIOUS techniques have been used to identify the recovery, recrystallization, and grain growth processes that occur when cold-worked metals are annealed. As early as 1928 work was conducted that indicated measurable density changes occur when cold-worked single crystals of brass are annealed.' More recently, work by Murphy exhibited a corre- lation of density with microstructural changes observed on annealing cold-worked polycrystalline a brass.2 Other investigators have performed similar work on a brass and copper.324 In reviewing the literature, it was apparent that density work had been limited to fcc materials. Therefore, it was the purpose of this investigation to determine the density changes that accompany annealing the cold-worked bcc material, molybdenum. Two degrees of cold work, 30 and 90 pct reduction of cross-sectional area by rolling, were selected for this study. EXPERIMENTAL PROCEDURE High-purity vacuum arc-cast molybdenum was used in this study, the principal impurity being carbon in the amount of 80 ppm. The final rolling reductions were made at 1200°C in grooved rolls to provide 5/8-in.-diam rod. Density specimens 0.500 in. diam by 1.5 in. long were machined from the bar stock. The specimens were ground to the final dimensions to provide a smooth surface. Density measurements were made using a hydrostatic technique similar to that used by ~urphy.' This type of equipment permitted weighing in liquid immediately after the air weighing. During each weighing the temperature of the air and liquid was controlled to within 0.0l°C. This was accomplished by sealing the analytical balance in an air-tight brass chamber and surrounding it by an insulated wooden case. Preheated air was circulated in the air space between the brass chamber and wooden case by means of a blower. The temperature of the

Jan 1, 1964

By N. Brown, H. Green

The effect of quenching temperature and of aging temperature and time on compression stress-strain curves of ß brass was investigated. Age softening occurs at a rate which decreases with decrease of quenching temperature below the critical temperature for ordering. The activation energy for softening is 15,400 cal per mol. No matter how rapidly brass is quenched or what the temperature from which it is quenched, practically complete order is obtained at room temperature. It has been demonstrated that with respect to the specific heat,',' electrical resistivity," X-ray diffraction, and microstructure, the slowly cooled and rapidly quenched specimens are the same and that complete long range order exists in both cases. However, Smith" showed that the hardness of ß brass depended upon the cooling rate and the temperature from which brass is quenched. Smith showed that the hardness was a maximum for specimens quenched from about 445 °C and that the as-quenched structure softened at room temperature at a rate depending upon the temperature prior to quenching. This softening after quenching is in this paper referred to as age softening. The results of this investigation are qualitatively the same as the findings of Smith. However, a more detailed analysis of these phenomena has been possible since the stress-strain curve offers a more sensitive index of the state of the metal than hardness. It is the purpose of this paper to show how the mechanical properties are related to the ordering of ß brass. A 200-lb ingot made from electrolytic copper and electrolytic zinc was extruded to 1/2in. rod. Chemical analyses at frequent intervals along the rod showed that the alloy contained 51.5 pct Cu with the greatest impurity being iron, at 0.01 to 0.001 pct. To obtain a constant test material, the 1/2in. extruded rod was warm-rolled to % in. diameter at 200°C and then recrystallized to a grain size of 2.0 mm. The specimens for the compression test were % in. high and % in. in diameter. The specimen ends were polished on 600 metallographic paper and coated with Molykote for a lubricant. The compression rig consisted of an anvil resting on the machined table of the Baldwin Southwark testing machine and a plunger fixed to the movable cross

Jan 1, 1954

By M. B. Bever, A. M. Reti, A. K. Jena

The results of this investigation show that in the system SnTe-PbTe l) the solid solutions have small exothermic heats of formation relative to the binary compounds, 2) solid-solution hardening is almost absent, 3) the tin and lead atoms are .randomly distributed on the sublattice occupied by them and do not undergo an ordering transition during a thermal treatment designed to promote such a transition, and 4) the lattice parameter changes linearly with composition. These findings suggest that the solid solutions of tin telluride and lead telluride approach ideal behavior. THE binary compounds SnTe and PbTe form a continuous series of solid solutions.' Information on several physical properties of these solid-solution alloys has been published.1"3 In the work reported here, the heats of formation, microhardness, and lattice parameters of these alloys have been measured and the possibility of an order-disorder transition has been investigated. Order-disorder transitions occur in some solid solutions of binary compounds. In the system Bi2Te3-BizSes, for example, the electropositive bismuth atoms and the electronegative tellurium and selenium atoms always occupy separate layers. In the disordered alloy Bi2Te2Se, the tellurium and selenium atoms are randomly distributed on the layers occupied by them, while in the ordered alloy they occupy distinct layers.4 The NaC1-type (Bl) structure of SnTe-PbTe alloys consists of two sublattices, one of which is occupied by the electropositive tin and lead atoms and the other by the electronegative tellurium atoms; any ordering would be expected to occur in the sublattice occupied by the tin and lead atoms. PREPARATION OF SPECIMENS Polycrystalline specimens of PbTe and Sn1-xPbxTe (x = 0.25, 0.50, and 0.75) were prepared by melting stoichiometric amounts of lead (99.999 pct), tin (99.98 pct), and tellurium (99.999 pct) in evacuated and sealed Vycor tubes. Because of the deviation of tin telluride from the stoichiometric composition5 this compound was prepared by melting 49.8 at. pct Sn and 50.2 pct Te. The tubes containing the melts were quenched into water; the solidified ingots were removed from the tubes and annealed for 2 weeks in vacuum (PbTe approximately 100°C below its melting point, the three alloys 100°C below their solidus tem-

Jan 1, 1969

By J. E. Cannaday, R. J. Austin, R. K. Saxer

PREVIOUS investigators have determined activation energies and have postulated various controlling mechanisms for creep.'-' Recently Barrett et 01.I5 have suggested, as the result of their work with cadmium, that the apparent activation energies for creep (AHc) above 0.5 T, could be correlated by means of activation energies for self-diffusion (AHSD) and modulus of elasticity functions: AHC = AHSD - (5RT/E) dE/dT. The wide disparity of apparent activation energies previously obtained with nickel compared to those reported for other fcc metals and the desire to test the postulate of Barrett el al. prompted this study. The as-received 17.5-mil nickel wire used during this work assayed 99.87 pct pure, Table I. X-ray analysis indicated that the wire was in a stress-re- lieved state and metallographic examination revealed an equiaxed grain size of approximately 0.01 mm. Specimens degreased in acetone and cut to 1-1/2 in. lengths were tested in a cam-mechanized constant-stress creep machine. A vacuum of at least lo-5 mm Hg was maintained during all tests. Stresses were applied when thermal equilibrium was established. When a measurable (at least 0.5 pct) secondary creep was observed, the temperature was pulsed to a higher temperature. Pulsing time varied from 30 sec at 480°C to 2 min at 1300'C and above. Slopes of creep curves were determined after the initial acceleration in the strain rate had subsided and steady-state creep was achieved. To confirm the results obtained, additional tests were performed incorporating a temperature pulsing method suggested by sherby. In this method the load was removed during temperature pulsing and reapplied after thermal expansion had occurred. No appreciable differences in results were obtained. Tests were performed over a wide range of temperature (470" to 1310°C) and stresses (250 to 17,000 psi). The expression was used to calculate activation energies. In this expression T1 and T2 are the initial and final temperatures, and el and i2 are the creep rates at T, and T2. The variation of the apparent activation energies with the mean test temperature calculated by means of Eq. [I] are shown in Fig. 1. The mean test temperature (Tmean) was calculated from the relationship

Jan 1, 1967

By Jos. J. Walsh

Ventilation within a coal mine is essential to the welfare of those employed therein, from the standpoint of health, safety, and efficiency. While the saving of life and the preserving of health are the chief reasons for ventilation, efficiency and production are increased. In spite of the fact that we speak of air as having a certain composition, the proportions of oxygen, nitrogen, and carbon dioxide are not fixed, but vary between small limits. The different elements are not chemically united, they are merely mixed and each is free and can be separated with little energy. For this reason air in the mine workings is seldom found in a pure state. Factors that necessitate ventilation in coal mines are those that change the composition of pure air. Contamination of mine air results from the burning of oil-fed flames, the use of explosives, the oxidation of coal, and the liberation of gases by the coal. The extent to which these factors exist governs the size and general plan of the ventilating applianccs required. An efficient ventilating system is one that will furnish air at the working faces in sufficient volume to dilute and render harmless noxious gases and at the same time maintain an oxygen content closely approaching that of pure air. In a well-ventilated mine, the oxygen seldom falls more than 0.5 per cent. below normal. The carbon-dioxide content of the air in the average coal mine will vary from 0.1 to about 0.8 per cent., which amounts are not harmful. Three per cent. of carbon dioxide in air doubles the frequency and the depth of breathing; it is plainly noticeable and if breathed continuously for several hours its effect would probably be harmful. Slight reductions in the oxygen content of the air, such as occur in well-ventilated mines, have no debilitating effect on the worker. A person not exerting himself would fail to observe any unusual physical effect in an atmosphere: containing 17 per cent. of oxygen. This condition, however, or even a condition showing an oxygen content below 20 per cent., would indicate poor ventilation and that the elements which tend to reduce the efficiency of the worker are present, namely water vapor and a high wet-bulb temperature.

Jan 1, 1923

By Jos. J. Walsh

Ventilation within a coal mine is essential to the welfare of those employed therein, from the standpoint of health, safety, and efficiency. While the saving of life and the preserving of health are the chief reasons for ventilation, efficiency and production are increased. In spite of the fact that we speak of air as having a certain composition, the proportions of oxygen, nitrogen, and carbon dioxide are not fixed, but vary between small limits. The different elements are not chemically united, they are merely mixed and each is free and can be separated with little energy. For this reason air in the mine workings is seldom found in a pure state. Factors that necessitate ventilation in coal mines are those that change the composition of pure air. Contamination of mine air results from the burning of oil-fed flames, the use of explosives, the oxidation of coal, and the liberation of gases by the coal. The extent to which these factors exist governs the size and general plan of the ventilating applianccs required. An efficient ventilating system is one that will furnish air at the working faces in sufficient volume to dilute and render harmless noxious gases and at the same time maintain an oxygen content closely approaching that of pure air. In a well-ventilated mine, the oxygen seldom falls more than 0.5 per cent. below normal. The carbon-dioxide content of the air in the average coal mine will vary from 0.1 to about 0.8 per cent., which amounts are not harmful. Three per cent. of carbon dioxide in air doubles the frequency and the depth of breathing; it is plainly noticeable and if breathed continuously for several hours its effect would probably be harmful. Slight reductions in the oxygen content of the air, such as occur in well-ventilated mines, have no debilitating effect on the worker. A person not exerting himself would fail to observe any unusual physical effect in an atmosphere: containing 17 per cent. of oxygen. This condition, however, or even a condition showing an oxygen content below 20 per cent., would indicate poor ventilation and that the elements which tend to reduce the efficiency of the worker are present, namely water vapor and a high wet-bulb temperature.

Jan 1, 1923

AN intermetallic compound, Ni3A1, has an ordered fcc structure of type Ll2, and shows peculiar dependence of the yield stress upon temperature; i.e., the yield stress increases by a factor of six upon raising the temperature from 77" to 900K1, 2 This compound is technologically important, since many nickel-base superalloys owe their high-temperature strength to the peculiar yield stress behavior of Ni3Al. The only study of the elastic behavior of this compound was made by Davies and Stoloff,1 who determined Young's modulus of poly crystalline Ni3A1 between 300" and 730°K. The determination of single-crystal elastic constants of Ni3A1 is therefore of interest in connection with dislocation dynamics and is reported in this paper. A single-crystal specimen, 1 by 1 by 3 cm, was cut from an ingot generously supplied by Dr. B. H. Kear of Pratt & Whitney Aircraft. Following initial machining with a Servomet and a surface grinder, the specimen was etched and annealed at 1100°C for 5 hr in vacuum followed by furnace cooling. Two parallel faces were oriented normal to within ±l deg of a [I101 crystallographic axis by the back-reflection Laue technique. The parallel faces were hand-lapped, etched, and polished by the usual metallographic procedures. Final thickness along the [I101 axis was (0.9325 * 0.0005) cm. Chemical analysis gave an average composition of 87.35 pct Ni. Total impurity content is esimated to be no more than 0.1 pct. The elastic constants were calculated from measurements of ultrasonic waves which were propagated along the [110] axis. A longitudinal wave and two shear waves whose displacements are aligned along the [ 110], [li~], and [001] directions, respectively, are necessary in order to completely specify the three elastic constants. Two 3/6-in. quartz transducers were bonded to the parallel faces of the sample with ~ac-seal.3 Although this bond was sensitive to thermal shock, it performed satisfactorily over the entire temperature range for both longitudinal and shear wave propagation. A frequency of 5 mHz was employed in the method of Williams and Lamb4 in order to measure the absolute value of the ultrasonic velocity. The pulse-overlap technique of Mcskimin5 was also used at this frequency in order to determine the shift in the ultrasonic velocity

Jan 1, 1970

By J. D. Lubahn

The Bauschinger effect, or rounding of the corner of the stress-strain curve upon reloading, represents a temporary apparent softness that is more pronounced at large strains than small and for complete unloading than for partial unloading. Interrupted creep tests on copper exhibit a similar temporary softness (high creep rate) upon reloading. The fact that the strainwise dying-out time of these effects is the same in both tensile and creep tests shows that they are related. Thus, the term Bauschinger effect appears to embrace behavior following partial or complete unloading and reloading in addition to behavior following reversed loading. It is suggested that the term may properly apply also to certain creep behaviors following a small load decrement. INTERRUPTED tensile tests at low temperatures show1 a rounding of the corner of the stress-strain curve for reloading, which indicates a temporarily low deformation resistance. In the absence of recovery, the curve soon rises to the value that would have prevailed if the test had not been interrupted. The rounding of the reloading tensile curve has sometimes been referred to1 as the Bauschinger effect, although the term is more commonly applied to low deformation resistance in compression following tensile prestrain. The unusually broad usage of the term Bauschinger eflect in ref. 1 seems justified by the obvious interconnection of the various behaviors to which it has been applied.' In fact, the following discussion will indicate that still broader usage might be desirable. The Bauschinger effect is common at room temperature but apparently disappears at higher temperatures.2 Interrupted creep tests and tensile tests were made on certified OFHC copper (nongaseous impurities exclusive of silver were 0.004 pct), cold drawn 84 pct to ½ in. diam, and annealed at 600" (about 0.025 mm grains) or 850°C (about 0.2 mm grains). The tests were made in standard creep or tensile machines, using an O.S. Peters microformer-type extensometer or, for the small plastic strains, a special arrangement employing General Electric magnetic gage heads.' Interrupted creep tests at room temperature show3,4 an initial softness after reloading, manifested by an initial creep rate that is higher than that which would have prevailed if the test had not been interrupted. Fig. 1 shows some typical examples. This effect is apparently temporary (as is that in tensile tests): in four of the five tests shown, the log rate vs strain curve becomes parallel to an

Jan 1, 1956

By F. L. Toy, C. E. Sims

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By O. D. Sherby, J. E. Dorn, C. D. Wiseman

MCLEAN' has shown that the total strain obtained during creep of aluminum polycrystals arises exclusively from the mechanisms of 1) microscopically observable slip, 2) subgrain tilting, and 3) grain boundary shearing. Extensive analyses, however, suggest that the high temperature creep of metal polycrystals is controlled by a single thermal activation process."" These somewhat contradictory observations might be reconciled if it could be shown that the activation energies are identical for each of the mechanisms isolated by McLean. Such identity of the activation energies, of course, would demand that the same unit process controls the functioning of each individual mechanism. Under these conditions the activation energies for creep of single metal crystals and polycrystalline aggregates and for grain boundary shearing should be identical. This paper is primarily concerned with the possible identity between the activation energies for high temperature creep of single crystal and polycrystalline metals. In addition, comparisons will also be made between the activation energies for creep of single crystals and polycrystals with previously reported activation energies for grain boundary shearing.0"8 Materials and Techniques The same high purity aluminum, lead, and tin were used in the creep tests for single crystals and polycrystalline aggregates. Single crystals of aluminum and tin were prepared by the strain-anneal technique, whereas lead single crystals were prepared by growth from the melt. The tensile creep stress was maintained constant by Chalmers-Andrade parabolic-type lever arms. Strains were measured to &0.0002 in. per in. with rack and pinion type extensometers, and temperatures were maintained to within & 0.2"C of the reported values by mercury-thermoregulated resistance-heated silicone oil baths. The previously reported unambiguous technique for determination of the activation energy for creep was employed throughout this investigation.' ." It involves periodic abrupt small changes in temperature during the course of creep, accomplished by rapidly replacing one creep bath at temperature TI by a second bath at T,. The abrupt change in creep rate from i, to & attending the abrupt change in temperature is due exclusively to the change in temperature, since both the stress and the substructure are identical the instant before and the instant after a change of temperature. Therefore, all other factors being identical where AH is the activation energy for creep and R is the gas constant. Results Typical examples of the creep rate vs creep strain data during temperature cycled creep tests of single

Jan 1, 1958

By J. H. Swislzer

TWO-LIQUID miscibility gaps have been found to exist in both the CaO-SiO, system above 1705 and the Cr,03 system above 2200"c. Glasser and 0sborn3 studied the extension of these miscibility gaps into the Ca0-Si0,-Crz03 ternary system and reported that the two-liquid region is not present at temperatures below the monotectic temperature of 1705°C in the CaO-SiO, system. The present authors, in connection with other work on surface-tension measurements and foam stabilities in the same ternary system,4 observed that the miscibility gap exists at temperatures as low as 1600°C. A brief experimental study was devoted to deter- mining tie-line positions in the two-phase region. The technique used was to obtain a separation of phases at 1600°C, then to quench-in the high-temperature phases and obtain a chemical analysis of each phase. It was necessary to take special precautions in obtaining a phase separation because of a tendency toward emulsification of the two liquids. The procedure followed is described in the schematic drawing in Fig. 1. A small platinum crucible containing several pinholes on its sides was placed inside a larger platinum crucible. An excess of Crz03 was placed in the outer crucible, together with a prefused binary CaO-Si02 mixture, and the Cr203 was allowed to diffuse through the pinholes and saturate the same binary CaO-SiOl mixture in the smaller crucible. After equilibration at 1600°C, the inner crucible contained only the lighter liquid (liquid A) saturated with Cr203. The outer crucible contained layers of both liquids. Experimental data were obtained by analyzing the entire contents of the inner crucible and only the bottom layer of the larger crucible (liquid B). The upper layer of the outer crucible was not suitable for chemical-analysis purposes because dispersions of the second phase sometimes were found in the samples. The technique is described in more detail in Ref. 4. The same method was used by Grieveson and urkdoan' to study a miscibility gap in sulfate-ferrite melts, where the liquids were difficult to separate because of similarities in density. In addition to the phase-separation experiments, a few others were conducted to obtain information

Jan 1, 1964

By W. F. Stowasser

Robert E. Hagen (Oliver Iron Mining Div., U. S. Steel Corp.)—Mr. Stowasser and his associates are to be congratulated on their achievements in developing the design of a pilot agglomerating plant, based on information obtained from experiments made in a laboratory sinter pot, and subsequently constructing and successfully operating this plant. In his Transactions article, May 1955 (vol. 201) Mr. Stowasser stated that the output of his heat treating strand was about 2 Lt per sq ft of grate area per day and that the fuel consumption was 0.7 to 0.8 million Btu per Lt of product. If it is assumed that the burning zone extends from the back of the ignition furnace to the beginning of the recuperation windbox, only about 1/3 of the grate area over the windboxes is utilized for burning pellets, and the actual rate at which partially dried pellets are burned is about 6 Lt per sq ft of grate area per day. It may be interesting to compare the above operating data with that obtained at the Extaca plant, where taconite concentrate is treated on a conventional sin- tering machine using limestone or hydrated lime additives with no recuperation of heat. The entire windbox area is used for burning, and a production rate of 2.5 Lt per sq ft of windbox area per day has been attained at a fuel consumption of 1.8 to 2.0 million Btu per Lt of product, the latter being considerably in excess of that reported by Mr. Stowasser, partly because a circulating load of returns amounting to 28 to 30 pct of the machine feed is used and because no attempt is made to recuperate heat from the waste gases. With the high capital and labor costs prevailing today, it seems that future development of the downdraft grate pelletizing process should be directed toward taking advantage of the high burning rate of predried pellets and increasing capacity, perhaps at the expense of fuel economy, by decreasing the proportion of grate area utilized by ancillary functions. For example, eliminating the cooling zone and using this area for burning would increase the proportion of grate area available for burning from 33 to 50 pct of the total windbox area, and a proportionate increase in capacity would result.

Jan 1, 1956

There is plenty of sulphur available but not at the price currently being paid for brimstone. Immediate shortages may be felt before the market adjusts, making marginal sources and by-product sulphur and acid available. (See P. 403) Government aid for mineral exploration is available and regulations governing applications are available from The Defense Minerals Administration, Dept. of Interior. lust ask for M0-5 and also for the contract form which is MP-103.

Jan 5, 1951

By Orville R. Lyons

THE Russellton preparation plant of Republic Steel Corp., located north of Pittsburgh, Pa., prepares 395x0-in. Thick-Freeport coal by means of a 13-ft 6-in. diam Chance cone and 16 No. 7 Deister tables. The plant feed ranges between 370 and 410 tons per hr, of which approximately 31 pct is 1/4xO-in. size, and the plant reject ranges between 14 and 16 pct of the feed.

Jan 6, 1953

By R. A. Meussner, R. J. Goode

Six intermediate phases occur in the Nb-Zn sysThese phases form by peritectic reactions at 1120°, spectively. The Nb Zn 15 phase appears as the minor phase in the eutectic structure, and the terminal phases remain nearly pure niobium and zinc even at high temperature. Vapor -pressure measurements on the four high-temperature phases (Nb Zn to Nb Zn 3) permitted estimates of the composition limits of these phases and the calculation of approximate values of AFO, AH°, and AS°. 1 HE present study of the constitution of the binary Nb-Zn system was a part of an analysis of the mechanism by which coatings of the Nb-Zn intermediate phases protect niobium against oxidation at high temperature.' Since the primary interest in these phases was in coating service, attention in this study was given principally to the four phases stable at high temperature with only cursory attention to the two low-temperature phases. The solubility studies of niobium in zinc by Martin, Knighton, and Feder2 and the reports from the present study of the Nb-Zn coating represent the only published data pertaining to this system. Previously Hodge, Evans, and Hoskins, in an experimental survey, had noted that niobium was not resistant to attack by molten zinc, but no further observations were reported. EXPERIMENTAL PROCEDURES a) General. The nature of the binary Nb-Zn system precluded the use of more conventional methods of determining the phase equilibria such as thermal analyses of a series of cast alloys. An extrapolation of the liquidus data of Martin, Knighton, and Feder2 to higher temperatures suggested that the solubility of niobium in zinc would remain low in the entire temperature range of interest. The preliminary results of the present studies showed that all of the high-temperature intermediate phases form by peritectic reactions. Thus the sluggish nature of this type of reaction and the steepness of the liquidus indicated that thermal analyses would not yield reliable data. The peritectic reactions, of course, precluded the direct formation of samples of the individual phases from the melt. b) Materials. The niobium and zinc used in the present studies were of high purity. The niobium, in the form of 0.1-in.-diameter rods, contained 30 ppm 0, 30 ppm N, and 15 ppm C. Aside from 0.05 pct Ta, the metallic impurities (iron, titanium,

Jan 1, 1965

By Jesse O. Betterton

In the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200' to 1300" I?. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accomplish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flour of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes. Essentially this process consists of circulating the lead by means of a pump in a kettle through a closed reaction cylinder, gaseous chlorine entering the reaction cylinder with the stream of lead from the pump. Molten zinc chloride is thus produced and is discharged together with

Jan 1, 1937

By Howard B. Bradley, Charles F. Weinaug

The phase behavior of a naturally occurring hydrocarbon system whose critical temperature is near the reservoir temperature has been described. The same volume per cent liquid was observed for the firkt time at three different pressures for isotherms immediately below the critical temperature. The shapes of the isothermal equilibrium constant curves necessary to predict this phenomena are discussed and illustrated. INTRODUCTION The phase behavior of a number of hydrocarbon systems has been reported; however, very little data are available on natural occurring hydrocarbon systems whose critical temperature is near the reservoir temperature. This appeared to be the case for the fluid studied here; therefore the pressure-volume-temperature data for this system were determined for preqentation. METHOD The PVT data were obtained with equipment similar to hat described by Weinaug and Katz,1 consisting principally of a two-section, double-windowed gauge mounted in a conktant temperature air bath. The procedure followed was essentially that used by Katz and Kurata5 except that a cathetom-eter, reading direct to 0.01 cm, was used to determine the height of each extreme phase limit. The system studied was formed by recombining -.vapor and liquid samples from the first stage separator of the well. Portions of these samples were displaced with mercury into the cell which had previously been filled with mercury. A predetermined amount of the liquid sample was introduced, while an excess of vapor was admitted. The resulting mixture was brought to equilibrium at the condition of the separator during sampling. By adding mercury to maintain the pressure, enough vapor was displaced to give a gas/oil ratio within the cell equal to that produced by the separator at the time of sampling. The remaining material was then considered to be equivalent to the reservoir fluid. An analysis of material in the cell, computed from analysis of vapor and liquid samples and the separator gas/oil ratio. is given in Table I. Table I — Composition of Hydrocarbon System Component Mole Per Cent Carbon Dioxide 0.13 Nitrogen 0.76 Methane 53.91 Ethane 14.20 Propane 9.64 Iso Butane 1.25 Normal Butane 4.29 Iso Pentane 1.12 Normal Pentane 1.87 Hexane 2.72 Heptanes + 10.11 hloleculal. Weight of Heptanes + 178.50

Jan 1, 1951

By C. Ernest Birchenall, Gerd M. Rosenblatt

The pressure and molecular weight of the antimony vapor over solid solutions of tin in antimony, containing 97.4, 94.9, 93.0, and 90.7 at. pct Sb, have been measured from 445° to 545°C by the torsion-effision method. The vapor is all Sb, within experimental error. A solidus curve which differs somewhat from the accepted curve has been calculated using the measured antimony activities. Metallographic examination of additional annealed alloys substantiates the accepted solidus. The solid solutions, which show negative deviations from ideality, probably do not deviate greatly from regular solution behavior. HANSEN' considers the Sb-Sn phase diagram to be well established with the exception of the boundary of the (Sb) phase.* Although there have been no pre- Their data can be combined with data for the solid alloys to calculate the solidus curve of the (Sb) phase. This paper presents measurements of the pressure ant1 molecular weight of antimony over Sb-Sn solid solutions containing 97.4, 94.9, 93.0, and 90.7 at. pct sb. Measurements were made by simultaneous use of the volmer3 torsion and Knudsen, effusion methods. The results of these measurements have been combined with the vapor pressure of pure antimony5 to obtain the activity of antimony in the primary solid solutions. The solidus curve calculated from these data differs somewhat from the accepted curve and is rather uncertain. Metallographic examination of Sb-Sn alloys was carried out to clarify the position of the solidus of the (Sb) phase. EXPERIMENTAL The apparatus and technique have been described previously.5 The measurements were made with the same effusion cells and torsion wire used in the measurements on pure antimony. The torsion measurements were calibrated with mercury at 30" using a mercury vapor pressure of 2.96 x 10-3 mm Hg determined by concurrent, absolute, weight-loss experiments. As in the measurements on pure antimony, an extraneous vapor was observed to distill off during the first run after the cell had been loaded with A fresh sample of alloy and during the first minute or two of every run. The change in composition after a series of runs with one sample was of the order of 0.1 at. pct and thus completely negligible in the calculation of the thermodynamic properties. The alloys were prepared from pieces of Merck antimony and Matheson, Coleman, and Bell reagent-

Jan 1, 1962