Search Documents

By Charles H. Moore

When lime and magnesia are used as fluxes in the smelting of titaniferous ores fluid, digestible slags low in iron oxide and high in titanium dioxide are produced. The mineral phases present in such slags are (Fe,Mg)O.2TiO2, CaTiO3, and minor amounts of silicate glass (or its devitrification products). The flux additions are added to the ore in relative amounts to crystallize a ratio of (Fe,Mg)O.2TiO2 to CaTiO2, of near the eutectic proportions of 60 pct (Fe,Mg)0.2TiO2 and 40 pct CaTiO3. FeO-Ti02 (ilmenite) remains present in the slag until the FeO content is reduced to approximately 8 pct. Op- timum slag composition is obtained by reducing the FeO content to between 2 and 6 pct. Continued reduction shifts he (Fe,Mg) 0.2Ti02 to oxygen deficient structures classified as MgTi30e and MgTi204. Further reduction yields titanium oxycarbides and freezes the melts.

Jan 1, 1949

An unexpected demand having entirely exhausted the Institute's supply of the Bulletins for January and February, 1916, the sum of $0.50 each will be paid for. a limited number of copies of these Bulletins, which send to the Secretary of the Institute.

Jan 5, 1916

By Sherwin F. Kelly

MANY baffling problems of crustal geology-of warping and folding, elevation, subsidence, and great dislocations of the earth's surface-may now be on the verge of yielding to the science of geophysics. Electric, magnetic, gravitational, geothermal, and seismic methods are being turned to the gathering of geological evidence buried by deep layers of rock, or lying beneath the waters of the oceans. In this hope, B. L. Miller expresses the opinion that these geophysical studies will sup- ply useful data bearing-on some of the more theoretical problems of North American geology. Among these for example, is the explanation of how Appalachia disappeared. This ancient land mass is supposed to have foundered beneath the Atlantic Ocean after the close of the Paleozoic era and the question arises, was it warped or faulted downward? The geophysical data, though meagre, indicate that the surface of the dense, basal rocks, the probable remnant of ancient Appalachia now underlying the Continental Shelf, slopes downwards to a depth of some two miles below sea level at a distance of 140 mi. from shore: thus suggesting that the subsidence was the result of warping downward rather than abrupt faulting.

Jan 1, 1938

By J. M. Roberts, D. M. Barnett

The activation energy required to break a pinned dislocation line away from its condensed atmosphere of impurity atoms is calculated as a .function of applied stress, without neglecting line tension. Reasows are presented for not assuming the effect of line tension to be negligible when considering the problem of freeing a small segment of dislocation from an impurity atmosphere. The dislocation is considered to he pinned at each atomic size along its length and the pinning points are assumzed immobile. The development is a refinement of the origznal cottrell-bilby1 theory. The solution is compared to recent approximations developed by cottrell3 and Haasen5 in which line tension con- IN 1949 Cottrell and bilby1 considered the problem of determining the force required to pull a dislocation away from its condensed atmosphere of impurity atoms. They also examined the effect of thermal fluctuations on this force. The dislocation line was pictured as bowing out in a triangular loop under the action of an applied stress, and the activation energy necessary to free the dislocation from its atmosphere was calculated as a function of stress, line energy, and dislocation-solute atom interaction. siderations were neglected. A qualitative explanation of the yielding process in terms of the activation of Frank-Read sources is presented, but the lack of a realistic solution to the dynamic dislocation problem involved prevents an extension of the model at present. A self-consistent correlation between the present calculations and experimental data for delay time associated with yielding and the temperature dependence of the upper yield stress was made. Favorable agreement was noted. It is concluded that extension of the original Cottrell-~ilby' theory which includes line tension effects can just as well describe the yielding process as other approximations3,5 which neglect line tension. Cottrell and Bilby found the form of the activation energy vs stress curves to be almost independent of the line energy and the interaction energy (i.e., these parameters only affected the activation energy U by a scale factor). A check of the theory was accomplished by comparison with the experimental data of McAdam and Mebs2 for the lower yield stress as a function of temperature. cottrell,3 in 1957, attempted to obtain a simple closed-form solution for the activation energy as a function of stress by linearizing the quartic equation relating displacement of the dislocation line and applied stress. It was argued that since the contribution to the line energy/atomic plane of a dislocation is made by the long-range stress field of the dislocation through a term of the type (Gb3/2p)ln A/ro, where

Jan 1, 1963

By Arnulf Muan, Carlos Landolt

Equilibria involving Cu-Pt alloys, copper oxides, and atmospheres of known ox2gen pressures have been determined at 1000' and 1200 C. The data obtained have been used to calculate activity-composition relations in the alloys. A moderate negative deviation from ideality is found. At high copper concentrations, the results of the present study are in good agreement with those of previous investigators, whereas at low copper concentrations the activities obtained in this investigation are slightly higher than those reported previously. The present study is part of a research program dealing with the determination of phase relations and thermodynamic properties of copper-containing systems at high temperatures. The information available for such systems is very scanty, particularly for copper oxides and their combinations with other oxide components. Platinum is commonly used as a container in studies of oxide equilibria. To evaluate quantitatively the extent of reaction between the oxide and the container, a knowledge of activity-composition relations in Cu-Pt alloys is necessary. Such data are not available for Cu-Pt alloys in the temperature range of particular interest in the present research program, and particularly for alloys low in copper. Studies of various aspects of the systems Cu-Pt and Cu-0 have been reported in previous literature. The system Cu-Pt is known1 to form a continuous solid-solution series above 812.C, whereas ordered phases are present in certain composition ranges at lower temperatures. Thermodynamic data for the system have been reviewed by Hultgren et al.,' who presented free energies of mixing at 65Oo C, mainly derived from electromotive force cell measurements by Weibke and Matthes.3 Enthalpies of mixing at 640°C have been obtained by Oriani and Murphy4 with liquid tin calorime-try. Their results differ considerably from those derived from the temperature dependence of the data of Weibke and Matthes. Thermodynamic data for the disordered alloys have been obtained by Assayag,5 and more recently by Schmahl and Minzl,6 by Myles and Darby,7 and by McCormack, Myers, and Saxer.8 The two latter sets of data7'' became available after the present study was completed. In the system Cu-0+ two oxides are stable at high temperatures, CuO and CuzO+ each having only minor deviations from stoichiometry. Equilibria in the liquidus temperature region of the system Cu2O-CuO have been studied by Roberts and systemsmyth,9'10CuzO-CuO by Vogel and ocher,I1 by Osterwald,12 and recently the the present authors.13 The system is of the eutectic type with a eutectic temperature of 1083.C The composition of the eutectic liquid corresponds to Xcu0 = °.44, and the oxygen pressure of the coexisting gas phase is Po2 = 0.55 atm.13 Equilibrium oxygen pressures for coexistence of solid CuO and solid Cu2O have been determined by Schmahl and Muller,l4 by Gadalla, Ford, and white,l5 by Bidwell,16 and recently by the present authors.13 There is reasonably good agreement among the various sets of data. Free energies of formation of Cu2O(s) from the elements have been derived by Tretyakov,17 by Bidwell,16 by Kiukkola and wagner,18 by Pal'guev and Neuimin," and by Steele and Alcock,20 There is particularly good agreement among the latter three1'-20 sets of data. THEORETICAL BASIS Consider a subsolidus isothermal section of the system Cu-Pt-0, as shown in Fig. 1. Two phase as-

Jan 1, 1970

By E. S. Bumps, W. F. Craig, M. Baeyertz

Metallurgists have looked at fractures macroscopically for many years and have evolved a vocabulary in which such words as "cleavage," "brittle," "shear," "ductile," "granular," "fibrous," and "silky" are used to describe the appearance of the fractured surface; but the meaning of these words in terms of metal structure is not well established. Observations of the structural meaning of "brittle" and "ductile" fractures in plate steels have been made, notably, by Kramer and coworkers1 and by Tipper.2 Grossman3 has studied the fracture of tempered martensite and combinations of ferrite and martensite. Notwithstanding these and other less concerted attacks on the problem, present understanding of fracture rests more on assumptions and logic than on experiment. It is the purpose of this paper to add a little to the growing fund of experimental observations of the nature of fractures in steel. The particular fractures to be described were obtained in conventional impact testing of an ordinary structural steel shape. In impact tests of the Charpy type, the specimens fail in a characteristic manner that depends on the steel and the temperature of testing. With ordinary structural and many other steel products, an appropriate range of testing temperature will cause a considerable change in the energy absorbed before fracture. This change is known as the energy transition and is accompanied, more or less closely, by alteration in the appearance of the fracture. At testing temperatures below the transition, the terms "brittle," "cleavage," or "granular" are used to describe the fracture; above it, "ductile" or "shear" are often used. Within the transition, the fracture changes from "brittle" to "ductile" by a progression in appearance, wherein the "brittle" portion of the fracture becomes restricted to a smaller and smaller central area of the fracture, as the testing temperature is raised and the "ductile" type of fracture is approached. All this is well known to metallurgists. The specimens under consideration are of the conventional V-notch Charpy type. They were taken from a structural steel shape of the following analysis: C Mn P S Si 0.17 0.46 0.009 0.029 0.03 Both longitudinal and transverse specimens were tested and examined. Fig 1 shows the energy values plotted against testing temperatures in the usual way. The curves for both longitudinal and transverse specimens show an energy transition, although the maximum energy absorbed at testing temperatures above the transition is greater in the case of the longitudinal specimens. Fig 2 illustrates the changes in the macroscopic appearance of the fractures that are associated with the energy transitions shown in Fig 1. Macrographs of the fractured surfaces of the specimens have been identified with the fracture ratings at intervals on each fracture curve. The numerical fracture rating on the ordinate of Fig 2 indicates the percentage of the area of each fracture that was considered to be "brittle" on macroscopic observation. Such rating of the fracture type in impact tests is now customary in many laboratories. Hereafter the specimens will be identified by reference to Fig 2 as 90 pct "brittle," 80 pct "brittle," and so on, in accordance with this macroscopic evaluation of the appearance of the fractured surface. The discussion of the fractures is divided into three parts. The first two are concerned with the mode of fracture and its relation to general structural features. As the same metal-lographic features occur in both longi-

Jan 1, 1950

By N. J. Grant, K. M. Zwilsky

A series of copper-alumina dispersion strengthened alloys were prepared using three different copper and two different alumina powder sizes. Improvements in strength of up to ten times that of pure copper were found in room-temperature as well as elevated-temperature stress-rupture tests. Conductivity values remained from 70 to 90 pct that of pure copper. The best alloys were based on the finest metal powder (1 p) and contained from 7.5 to 10-0 vol pet of 0.018 or 0,033 p alumina. DISPERSION strengthening of metals consists of strengthening a metal matrix by the addition of oxides or other refractory constituents, followed by strain hardening, in order to reinforce the base material and extend its temperature range of application. Since the discovery of SAP by lrmannl and Von zeerleder2 in 1949, many investigators have reported data obtained on a variety of metal-inert oxide alloys.3-7 The present work deals with the mechanical mixing of copper and alumina powders. While several techniques of introducing the second phase have been investigated to date, mechanical mixing so far has been recognized as the simplest, least expensive, and most universally applicable technique that can be used to obtain an ultrafine dispersion of inert particles. In the present case, the effects of changing the metal particle size, the oxide particle size and the volume percent of oxide were investigated. This work is an extension of a previous study.6 EXPERIMENTAL PROCEDURE The starting materials were three different grades of copper powder and two different alumina powders. The three metallic powders were -74 µ(- 200 mesh) electrolytic copper powder consisting of irregular equiaxed particles having a normal screen distribution and analyzing 99.5 pct Cu, and two powders having a 5-µ and 1-µ particle size, average, respectively. The latter powders were produced by the hydrogen reduction of purified sulfate solutions at elevated temperature and pressure and were furnished by the Sherritt Gordon Mines, Ltd. The alumina used was obtained from Godfrey L. Cabot Co., under the trade name of Alon C, one batch of powder having a particle size of 0.018 µ, the other a particle size of 0.033 µ. The crystal structure of these alumina powders was found to be cubic gamma. Each batch of powder was mixed in a Waring Blendor for a total of 15 min, followed by a low-temperature reduction in hydrogen and vacuum compacting in cylinders which were hydrostatically pressed at 35,000 psi to give a compact that could be handled conveniently. Six of the compacts were hydrogen sintered at 900°C while the remaining four were sintered at 1000°C. Subsequently, all compacts were hot extruded at 760°C with a reduction of area ratio of approximately 20 to 1. Evaluation of alloys included density and resistivity measurements, room-temperature tensile tests, stress-rupture tests at 450°C plus one other temperature per alloy, hardness tests, microstruc-tural examination, X-ray analysis of the dispersed phase after dissolving the metal phase, and oxidation studies on two of the alloys. A vacuum-melted, wrought copper rod was tested together with these alloys for comparison purposes. RESULTS Table I is a summary of the compositions, sintering temperatures, densities and conductivity values of the ten alloys prepared. All alumina additions are given in volume percent, and will be referred to as

Jan 1, 1962

By W. A. Wood, H. L. Wain, R. I. Garrod

The mechanical behavior of recrystallized chromil~m of high purity has been studied, principally in torsion and to a lesser extent in tension, at temperatures between —196oand 350oC. Depending upon the conditions of test, the material may show brittle or ductile behavior or an intermediate or subduc-tile state having some of the characteristics of each. This latter state existed at temperatures between approximately ±50°C and was characterized by a) extensive creep at stresses well below the normal fracture stress, b) nonelastic loading/unloading effects during creep, c) strain softening under cyclic loading, and d) final failure of a brittle type. Suggestions are made on the dislocation processes and interactions which give rise to subductile behavior The ductile-brittle transition in bee metals has been studied mainly by tension and bend tests. These methods, however, favor crack propagation which may follow too closely on initiation for detailed study of the transition itself. For work of this nature, therefore, other modes of deformation less favorable to crack propagation may be preferable. This paper describes a study of the ductile-brittle transition in chromium which is based mainly on torsional testing although a few subsidiary experiments were made in tension. It appears to reveal at the transition an intermediate state that cannot properly be described as either brittle or ductile. Torsional tests on chromium have been made by other workers1 but not, as here, primarily for study of this intermediate state. EXPERIMENTAL The chromium, in the form of swaged rod, was prepared by techniques already described.' The particular material used was one in which the main impurities were 0.03 wt pet 0 and 0.006 wt pet N and one in which transition from ductile to brittle states in torsion conveniently fell at about room temperature. For torsion, test specimens were from 5/16-in.-diam rod to provide test portions 1-1/4 in. long by 7/32 in. diam, a twist of 1 deg thereby corresponding throughout this paper to 0.0015 surface shear. The specimens before test were annealed for 2 hr at 1200°C in vacuo, which left them with a re-crystallized grain size of about 0.01 mm, and then electropolished. They were tested under dead-weight loading in an apparatus in which they could be surrounded by a furnace or cooling chamber, tests in practice being made at various temperatures between -196" and +350°C. For tension tests, cylindrical specimens were prepared in a similar manner and tested at room temperature under dead-weight loading. RESULTS (TORSION) Subductile State. The state described above as intermediate between brittle and ductile may be perhaps best defined by reference to torque/twist curves at various temperatures. These are grouped in Fig. 1. Below about -50°C the material was brittle, in the sense that it exhibited little plastic deformation under stress and fractured by cleavage along planes of maximum resolved tension, which in torsion produces the well-known helical type of fracture. The deformation is typified by the curves for -196" and -150°C in Fig. 1; it shows a slight but progressive deviation from linearity above a certain torque, here about 50 lb-in., until fracture occurs at about 95 lb-in. A feature to which it is desired specially to call attention is that under none of the loads did the specimens show significant creep.

Jan 1, 1964

By N. J. Grant, C. F. Flo, F. B. Cuff

An investigation of the Ti-Cr system has shown the presence of a complete series of solid solutions in the ß phase, with a minimum in the solid us near 50 pct Cr. An intermetallic compound, TiCr2, forms during cooling from the ß solid solution. There is a eutectoid reaction at the low chromium side of the system. IN view of the recognition of the potentialities of titanium and its alloys as important structural materials there has arisen a need for a systematic investigation of various titanium binary diagrams. Of these, the Ti-Cr system was of particular interest because of the improved properties imparted to titanium by small chromium additions. A literature survey disclosed a partial constitution diagram that had been suggested by Vogel and Wenderott,¹ This diagram, shown in Fig. 1, is the result of work done on the Fe-Cr-Ti ternary system. Alloys containing less than 43 pct Cr were not investigated. In addition to this, a study of alloys in the Ti-Cr system was reported by McPherson and Fontana.² Adenstedt3 furnished a number of dilato-meter curves obtained from specimens containing 5, 10, and 15 pct Cr. Very recently, McQuillan4 submitted a proposed diagram covering the complete range of compositions between titanium and chromium. This diagram was in general agreement with the one described here. Experimental Procedure Sponge titanium (99.7 pct) and electrolytic chromium (Bureau of Mines analysis: 99.03 pct Cr, 0.40 pct Fe, 0.53 pct O2) were used for the initial determination of the system. Subsequent refinement of points, particularly for the low chromium side of the diagram, was accomplished by using iodide titanium and high purity chromium (National Research Corp. analysis: 0.050 pct C, 0.045 pct O2). The Ti-Cr alloys were prepared by melting 25 g charges in an enclosed, water-cooled copper crucible using a movable tungsten electrode. The atmosphere was helium, prepurified by first passing it through a drying agent and then through sponge titanium heated to 850°C. Particular care was taken to avoid any large scale segregation resulting from insufficient mixing of the components. Each charge was melted and kept molten for approximately 1 min, allowed to cool, inverted, remelted, and kept molten for an additional minute. In order to ascertain the amount of impurity pickup (oxygen and nitrogen) during the melting procedure, three iodide titanium specimens were melted in sequence and then checked for increased hardness. The specimens in the as-cast condition showed a relatively large hardness increase over the hardness of the as-received iodide titanium. The scattering on these readings was large. However, after the specimens had been homogenized at 840 °C for 2 hr and slowly cooled, the measured increase in hardness over the as-received titanium was small with a corresponding decrease in scatter. The reason for this hardness change is that in heat treating these specimens below the transformation temperature (885°C) there was a conversion from the as-cast structure to the more nearly equilibrium structure of the annealed specimen. The alloys were analyzed for chromium content and although the actual percentage was invariably low the deviation from the nominal composition never exceeded 0.6 pct Cr.

Jan 1, 1953

By S. L. Couling, D. J-P. Adenis

i2) twinning in poly crystalline magnesium does not usually occur homogeneously but is concentrated in localized regions or bands inclined at about 45 deg to the stress axis. These bands of twinning are in many ways similar to the Luders bands seen in mild steel alzd Al-Mg alloys. Within a hand the percentage of the volume twinned may approach 100 with no twinning outside the band. Bands are not produced in specimens of grain size a3 x 10-= in. or in samples deformed at temperatures 300°F. Annealing of heavily twinned regions leads to re crystallization textures markedly different from those found in the starting material. The exact preferred orientation appears to depend on the starting grain size, the amount of compres-sive strain and the manner in which it is introduced. MAGNESIUM, with its hexagonal crystal structure, deforms plastically at room temperature by a variety of deformation mechanisms, one of the most important of which is (1012) twinning. In single crystals such twinning occurs on compression parallel to the basal plane or tension perpendicular to it. In wrought polycrystalline magnesium, such as rolled sheet, the preferred orientation is such that almost all the grains have their basal planes nearly parallel to the sheet surface. Therefore, if sheet material is deformed by cold rolling or by tension in the plane of the sheet, deformation of the grains by (1012) twinning is not favored. On the other hand, twins form readily on compression parallel to the plane of the sheet as in a compression test, on the compression side of a bent sample, or at the outer rim of a drawn cup. The first part of this paper deals with the morphology of (1012) twinning in polycrystalline magnesium. Some aspects of this subject were covered by Barrett and ~aller.' Of direct bearing on the work to be reported here are the comments of Jetter' in discussion to Ref. 1. He shows that Mg + 1.5 pct Mn alloy sheet when bent about a transverse axis develops a pattern of transverse bands on the surface of compression. A longitudinal section through the sheet shows that the bands are wedge-shaped and inclined to the rolling direction. The bands were identified as "outcrops of regions in which deformation is localized as the result of the reorientation brought about by (1012) twinning". The second part of the paper treats the recrys-tallization texture of the specimens twinned by compression. Magnesium deformed and then annealed generally recrystallizes with no change in orientation.1'3'4 This statement is true provided that the amount of (1012) twinning occurring during deformation is small. In an isolated observation, Anse15 has shown that, when deformation produces much (1072) twinning, annealing causes new maxima to appear in the pole figure. The second part of the paper elaborates on this point. I) MATERIALS AND PROCEDURES All of the experimental work to be reported was done using the commercial sheet and plate alloy AZ31B (nominal composition: 3 pct Al, 1 pct Zn, 0.4 pct Mn, balance magnesium). This alloy is available commercially in two tempers, -0 (fully annealed) and -H24 (partially annealed), and specimens of both tempers were used in various experiments. The average grain. diameter (AGD) for -0 temper 0.125-in. sheet is about 0.5 x 10- in.; where material of larger grain size was desired, anneals at elevated temperature were used to grow the grains. compression tests were made on a screw-driven "hard" machine. The specimens were clamped in a

Jan 1, 1964

By Philip D. Wilson

FEAST and famine-or, chronologically, famine and feast-have characterized the aluminum supply program during 1943. Fortunately for the war effort the famine phase is over and aluminum production is now in the happy position of being abundantly able to supply all the requirements of the armed services plus a monthly surplus which is building up a substantial stock pile as a reserve against any contingencies. But the present condition of oversupply cannot be attributed to the super-efficiency of the aluminum production program which was designed to take care of the over-all requirements of the war with little or no margin of safety. The present more than comfortable situation is due primarily to the fact that the armed services generally have not consumed anything approaching the amount of aluminum which their requirement estimates indicated.

Jan 1, 1944

By J. M. Vonfeld, V. D. Hanson, W. K. Heinlein

TWO overfeed drum-type separators using a suspension of magnetite in water as the separating medium have been installed in the Champion No. 1 preparation plant of the Pittsburgh Coal Co., Division of the Pittsburgh Consolidation Coal Company. A simplified flow diagram of the Champion No. 1 coarse coal circuit is shown in Fig. 1. A railroad car rotary dump, capable of handling 20 cars per hr, discharges the coal into a hopper. Coal is fed from the hopper of the rotary dump to a 60-in. belt conveyor by two reciprocating pan-type feeders. The belt conveyor feeds the run of mine coal onto the main raw coal screen. The first deck is fitted with 3 in. round hole perforated plate which removes the 3x0-in. coal. The second deck of the screen is equipped with 6-in. lip screens which separate the remaining coal into +6 in. and 6x3 in. The +6 in. coal is transferred to a shaking picking table and then discharged onto the loading boom. The 6x3-in. coal is fed to the No. 2 dense medium vessel for cleaning. The clean coal from this unit flows to a vibrating screen where the medium is removed and the coal sized into 6x4 in. and 4x3 in. The 6x4-in. coal is transferred to the loading booms and the 4x3-in. is conveyed to the clean coal classifying screens to remove degradation. The 3x0-in. raw coal is blended in a system composed of three storage bins having a total capacity of 400 tons. From these bins the coal is fed onto a 48-in. flight conveyor by three reciprocating feeders. This flight conveyor delivers the coal to the Rheo plant. The 3x0-in. coal is then cleaned in two 48-in. Rheolaveur launders each equipped with two Rheo boxes. The first set of boxes removes a primary refuse and the second set produces a middling product which is recirculated in the launders. The cleaned coal and water overflows from the primary launders to two sizing and dewatering shaker screens where the water and - 3/8-in. coal are removed for further cleaning in the Rheo fine coal plant. The 3x3/8-in. clean coal is combined with the 4x3-in. coal from the No. 2 vessel, sized into 4x2 in., 2x1 1/4 in., and 11/4x3/8 in., then sent to the loading booms. The 3x0-in. refuse from the primary launders is normally fed to the No. 1 dense medium circuit, but any portion or all of this material can, as an alternate, be processed in the Rheo rewash launder. The primary refuse when fed to the dense medium circuit is screened into 3/8x0 which is cleaned in the fine coal plant and 3x3/8 for cleaning in the No. 1 vessel. The clean coal from this vessel is passed over a vibrating drainage and rinse screen, then sluiced to the rewash sizing shaker where it is dewatered and sized for loading. The installation of a pilot plant separating vessel using a suspension of magnetite in water was pro-

Jan 1, 1952

By M. P. E. Desvaux, P. Charsley

OLIP-line observations on copper alloys, using the electron microscope, have been made by a number of workers,13 but this work has been confined to a brass. In a CuAl alloys Koppenaal4 and Koppenaal and Fine5 have made observations with the optical microscope and by the use of interferometry. They found that the observed slip step heights inside the Liiders bands accounted for only 42 pet of the total macroscopic strain. The suggestion was put forward that optically unresolvable slip in other parts of the specimen accounted for a major part of the macroscopic strain. This is surprising since it is known from other workers that slip in a brass is inhomogeneous; i.e., large amounts of slip occur on individual {lll) closelys paced than being shared by a large number of closely spaced planes. Furthermore, a brass and a CuAl alloys with high concentration of aluminum exhibit similar deformation characteristics and slip-line patterns. Prior to investigations into the behavior of copper and a CuAl alloys under reversed stresses in tension and compression, some preliminary experiments have yielded results which the authors think resolve this discrepancy, and throw some further light on the behavior of a CuAl in tension. An experiment was carried out on a 10 at. pet CuAl single crystal, of gage length 7.5 cm, diameter 3.1 mm, and orientation shown in Fig. 3 (inset), for the purpose of resolving the above discrepancy. The specimen gage length was electropolished for 10 min in a 50:50 orthophosphoric acid (SG=1.75)-distilled water system, with 2 v across the cell and a current density of 0.5 amp per sq cm. The cathode was made of copper. After a tensile strain of 0.067 ± 0.001, intense slip was observed over a length 2 cm of the gage length whilst the rest of the specimen was relatively undeformed. In the lightly deformed region, slip bands of mean width 20 /x were spaced about 1 mm apart on average. The transition from the heavily slipped region (usually called a Liiders band) to the lightly deformed region was gradual, the slip-band density increasing as the "Liiders band" was approached. In the latter, the slip bands became so close together that, to the naked eye, the specimen appeared to be continously slipped, and the typical microtopography of this region is shown in Fig. 1. Twelve electron micrographs were taken at random from replicas of the Liiders-band region, and the widths of the slip lines were measured. The slip lines account for an over-all tensile deformation of 7.0 ± 0.7 pet, after allowing for the lengths of the un-slipped regions, which is in good agreement with the macroscopic strain. The distribution of slip-line widths was also measured and is shown in Fig. 3. Since Koppenaal could not resolve slip lines with height less than 540A (limit of resolution represented by dashed line), then it was deduced that he could have measured only about 50 pet of the deformation within the 'Liiders Band'. It is concluded, contrary to the suggestion of Koppenaal,5 that virtually all the macroscopic strain is accommodated within the "Luders band" and that there is no need to invoke fine slip distributed uniformly over the gage length.

Jan 1, 1967

By F. A. Crossley

The key to disagreements between Blackburn's findings and mine is the word equilibrium". My work attempted to define the equilibrium diagram of the titanium-rich end of the Ti-A1 system. It can readily be shown that Blackburn's conclusions are based primarily on the examination of structures substantially removed from equilibrium. The diagram presented in Fig. 16 is properly labeled a "phase diagram". However, it appears that Blackburn either does not understand or does not accept the difference between "phase diagram" and "equilibrium diagram" as defined in the Metals Handbook.17 The conflict lies not in Blackburn's data but in his interpretation of it, and his use of "transformation", "phase diagram", and "equilibrium diagram" as synonymous terms. I share his view that the light microscope is much inferior to the transmission electron microscope for the study of transformations; but this fact does not render the light microscope useless or untrustworthy. The difficulties experienced with the Ti-A1 system have not been due to the limitations of the light microscope, but rather to the extreme sluggishness in achieving equilibrium at temperatures below 1000° C. Were it not for the light microscope employed with polarized light, the twin phase syndrome' might still be unrecognized and, as a consequence, still adding to the confusion of Ti-A1 investigations. (Ref. 1 should read ... Contract No. N161-25952 ... vol. 236.) Other, more sophisticated techniques, including electron transmission, simply confirm the erroneous tentative conclusions drawn from observations of structures due to the twin-phase syndrome. By the standards of most of the investigations of the Ti-A1 systems, seven of the fifteen compositions investigated by Blackburn were seriously contaminated with oxygen. The writer has found that 0.1 wt pct 0 shifts the a + Ti3A1 boundary to 1 at. pct lower A1 content at 700°C. At constant aluminum content, this corresponds to a temperature shift of the boundary of +25°c.18 Blackburn advises that the first group of alloys contained 0.1 to 0.15 wt pct 0, bur he does say whether the analyses were performed on as-received material or on specimens in their final state of heat treatment. This is especially important considering the 20-mil-thick starting materials. If specimens had been annealed in the two-phase a + 6 region it would have provided an indication of the final degree of oxygen contamination since up to about 12 at. pct A1 the boundaries of this region are well-defined for low-oxygen alloys. Blackburn questions the capability of light microscopy in determining phase boundaries in the Ti-A1 system. I submit that the a/a + Ti3A1 boundary in Fig. 1 of Ref. 1 over the composition range from 10 to 18 at. pct A1 was determined by dilatometry and supported by electron diffraction. Specimens of alloys containing 8, 10, 12, and 14 at. pct A1 were aged at 550°C for 1000 hr (under stress of 5000 psi to accelerate the tendency to equilibrium) and then fractured in tension at room temperature. Collodion was applied to the as-fractured (unetched) surface and, when stripped, carried away particles identified by electron diffraction as Ti3A1. Perhaps Blackburn will explain why these electron diffraction data were ignored. At this time, a technique for revealing or indicating

Jan 1, 1969

By R. A. Pasternak, B. Evans

In an ultrahigh-vacuum study of the sorption of nitrogen by niobium* resistivity data for this metal have been obtained as function of temperature and of low nitrogen concentrations. The ultrahigh-vacuum system in which base pressures of about 5 x l0-10

Jan 1, 1965

By J. Winter, W. C. Setzer, A. J. Goldman

ANISOTROPY in cold worked tempers of commercial aluminum alloys is manifested in deep drawn products as protuberances or ears 45 deg to the rolling direction. This reflects the {123}(412) rolling texture.' In fully annealed material, 0 to 90 deg ears in and per-

Jan 1, 1970

By C. K. Eilerts, J. D. Ham

Laboratory research has been conducted to evaluate the characteristic effects of condensate saturation on the mobility of gas in typical reservoir rocks. A pump with two pistons provided phases in equilibrium at controlled flow rates and constant liquid-vapor volume ratios. Core samples were tested in a holder that permitted sealing steady-state phases in the pore spaces under flow test pressures for weighing with sufficient precision to give an accurate measure of the attained saturations. Parameters of the study were pressure, apparent velocity, flowing liquid-vapor volume ratio, fluid composition, core material and length-to-diameter ratio. Tests were conducted at 515 and 1,515 psia to determine the effect of pressure on the mobility-saturation relationship. Influence of the apparent velocities 0.30, 0.15 and 0.07 cm/sec and of five liquid-vapor volume ratios from 0.0001 to 0.01 was determined at 515 psia The principal fluid system was nitrogen and and separator liquid from a Gulf Coast condensate, but the effect of a condensate of different viscosity was also determined. The significance of a possible concentration of liquid near the outlet end of the test cores was investigated. Core materials included a consolidated sandstone and a low-permeability limestone. Relative mobility and liquid-vapor volume ratio relationships are concluded to be dependent on pressure, saturation and, to a lesser extent, on velocity. For each porous medium and fluid there is a minimum saturation essential to two-phase flow, and high velocities of flow have only limited effect on saturations in this range. INTRODUCTION It is now recognized that knowledge of the availability of a reservoir gas — the period that gas may be recovered from a reservoir at a given rate — is as important as the estimate of gas in place. When reservoir conditions are such that pressure decline owing to production will result in retrograde condensation, liquid saturation can increase in the structure around the production well in a way that may restrict flow capacity, and hence future availability. l Based on a numerical solution of transient radial flow of single-phase gas-condensate fluids, 2 a program for computing the accumulation of condensate in a reservoir and the effect of this condensate on deliverability has been developed. During this development a need evolved for data that described the influence of pressure, velocity of flow and condensed liquid on mobility as recovery progressed. This paper presents the results of experimental investigation to obtain insight into the mobility relationship at reservoir pressures of gas-condensate fluids. A core holder for flow tests at reservoir pressure was developed to weigh the core and its fluid contents under pressure to determine saturation. A specially constructed pump was used to drive a two-phase fluid through the core until a steady state prevailed. The core was used as a differential device, and properties measured were intensive rather than extensive. APPARATUS Fig. 1 shows a schematic representation of the major pieces of equipment used in the mobility determination. The weighable core holder is connected to a two-piston, constant-displacement pump. Attainment of steady-state flow is indicated by stability of the flow differential read from the high-pressure manometer. WEIGHABLE CORE HOLDER An important part of the data needed was the mobility-saturation relationship. This required that mobilities and saturations be measured at pressures, flow velocities and liquid-vapor volume ratios characteristic of condensate reservoirs.

By W. O. Philbrook, A. E. El-Mehairy

The reduction by hydrogen of individual particles of dense hematite implanted in beds of inert spheres is controlled by single-particle kinetics. No evidence of reagent starvation was found down to low flow rates established by pressure gradients as low as 0.01 in. H2O per- in. of depth in beds of spheres as small as 3/16 in. diam. The optimum size for most rapid reduction of beds of homogeneous ores results from the effect on reducing potential of the gas of competing factors of supply and consumption. A recent publication1 presented the results of a study of the rate of reduction of iron ore in a fixed bed by hydrogen introduced at constant pressure differential. Under these conditions the reagent flow rate varied directly with the bed permeability, which was a function of particle size and shape and bed voidage, and inversely with the temperature-dependent viscosity of the gas. The present note adds data from supplementary experiments designed to reveal whether or not any partial reagent starvation arising from a flow-dependent transport resistance in the gas phase might have been operative. Kinetic studies were made of the reduction of individual spheres of iron oxide inserted into beds of inert spheres, so that the reagent flow rate and aerodynamic conditions were again determined by bed characteristics and temperature. The experimental techniques and apparatus were similar to those previously described.' The synthetic iron ore spheres were wet-rolled by hand from powdered, reagent-grade* Fe2O3 and subsequently dried and then fired in air at 1250°C. The indurated pellets has almost no porosity as indicated by their specific gravity of 5.10. The beds were made of dense alumina spheres, closely sized to the same dimension as the iron oxide spheres, in the following diameters: 3/16, 1/4, 5/16, and 3/8 in. Each bed was hand-packed of particles of a single size to a controlled voidage of 0.32 and depth of 3 in. within a capsule having an internal diameter at least 10 times the particle diameter. A few weighed iron oxide spheres were individually planted in the central plane of the bed of inert spheres at points away from the wall. Reduction was carried out at atmospheric pressure by purified hydrogen at 670°, 800°, and 985°c. The reagent was supplied at precisely controlled pressure differentials of 0.01, 0.02, and 0.03 in. of water per in. of bed depth. This gave a range of flow rates similar to that used in the study of beds of ore and comparable with blast-furnace practice in terms of mols of reducing gas per hr per sq ft of cross-section. Viscous flow prevailed in all beds under the experimental conditions of this study. The reduced particles were checked for loss in weight and then sectioned for metallographic examination. Occasional particles were found to have contained minute internal cracks that interfered with the concentricity of the reduction interfaces, and data for such particles were rejected. An experimental rate constant for the reduction of the imbedded Fe2O3 spheres was calculated on the assumption that the rate was proportional to the metal-oxide interface area by an equation that has been found by McKewan2 to describe the reduction of single spheres

Jan 1, 1962

By E. M. Cox, T. Rosenqvist

IN a recent investigation, carried out at the Institute for the Study of Metals, the affinity of sul-phur for iron, copper, and manganese was studied over the temperature range 700" to 1300°C.' It was found that copper exhibits a rather high affinity for sulphur, especially at higher temperatures; and attention was called to the possibility that copper when present together with sulphur in liquid steel would tend to lower the chemical activity of sulphur and thus interfere with the desulphurization process. It was clear, however, that the data for the equilibrium between pure copper and pure copper sulphide (Cu2S) could not give any quantitative information about the effect of copper when dissolved in liquid steel. The present work is concerned with the activity of sulphur in the diluted range of the binary iron-sulphur system, and with the influence of small amounts of copper on this sulphur activity. This investigation is in principle based on the same method previously described for the binary metal-sulphur studies;1,2 namely, reaction with hydrogen to form hydrogen sulphide. The equilibrium ratio PH2s/Ph2 in the equilibrium gas mixture is, for a given temperature, directly proportional to the sulphur activity. The activity of sulphur in liquid iron has previously been studied by Chipman and Ta Li,3 White and Skelly,4 and recently by Sherman, Elvander, and Chipman.5 Morris and Williams6 have studied the effect of added silicon, and Kitchener, Bockris and Liberman,7 and recently Morris and Buehl,8 the effect of added carbon on the sulphur activity. In present day steelmaking processes the steel bath contains between 0.01 and 0.1 pct sulphur, and the copper content may be as high as 0.5 pct. The equi-librium gas ratio (H2S/H2) would, for such a low-sulphur content, be too low to be measured with the experimental technique we use. It has been shown by previous investigators that the H2S/H2 ratio is closely proportional to the sulphur content up to about 1 pct sulphur. The sulphur activity at very low-sulphur content can therefore be calculated by linear interpolation between 0 and 1 pct sulphur. In order to show the general trend with increasing sulphur content, the present work has been carried out to about 3.5 pct sulphur. As the effect of copper was assumed to be more a function of the Cu/S ratio than of the absolute copper content, the runs with copper were made for certain constant values for this ratio.

Jan 1, 1951

By J. A. Clum, R. W. Heins, T. D. Tiemann

The use of Na-montmorillonite clay hinders (Western Bentonite) in the pelletizing of iron ore concentrates is well established as is the idea that alternative binders must be found. 1-6 This note summarizes work done7 in evaluating a Wisconsin montmorillonite clay binder. The clay occurs in irregualr beds overlying the Prairie du Chien Dolomite and the St. Peters Sandstone near Hersey, St. Croix County. The raw Wisconsin clay contained 65% quartz and 35% clay minerals. The Na20to CaO ratio was 0.234. Suspension viscosity tests of the raw clay gave results only slightly better than water alone, even after treatment with activator materials. Sedimentation treatment reduced the quartz in the decantate to 5% after 240 min (four hours). Twenty minutes of sedimentation produced a decantate with 27.5% quartz which was found as effective as the 5% quartz decantate in pelletizing behavior. The 20 min decantate was used in subsequent tests. The decantate was filtered and dried at 110°(230°F). The minus 200 mesh portion of this was added directly to the magnetite concentrate. Pellets were made in a laboratory sized disc pelletizer from pastes consisting of ore concentrate, balling water (9%) and binder (clay, or clay + resins, or resins). The pastes were premixed in a Waring blender. The binders were: (1) 1% of a commercially used Western Bentonite; (2) 1 % or 3% of the Wisconsin clay (raw, or 20 min decantate); (3) 20 min decantate washed with activator solutions, (to exchange Na for Ca in the clay); (4) decantate with activator added in the balling water; (5) decantate with organic resins; (6) organic resins. Measurements of the 0.46 m (18 in.) Green Drop Number, the Dry Strength and the Fired Strength (fired at 1260°C (2300°F) for 30 min) were made. The dry and fired compressive strengths were determined on an Instron testing machine using a C-load cell and a F-load cell, respectively. The cross-head speed was 0.004 m/sec (0.1 in./min) for both. The results of each measurement were averaged for 15 pellets. A summary of those results is presented in [Table 1]. More detailed results and procedures are presented in another report.7 In addition to the effects on pellet strength due to various binders the effect of varying magnetite concentrate characteristics is noted in [Table l]. There, a few comparative data are shown for Cornwall, PA Magnetite, which has a generally liner particle size than the Black River Falls magnetite which was used for most of the tests.

Jan 1, 1979