Search Documents

By William E. Bruce

In recent investigation of drilling processes, the U.S. Bureau of Mines measured the operating characteristics of two percussive drills. Basically, this entailed measuring maximum piston velocities while drilling. The maximum piston velocity is not necessarily the same as the striking velocity. The latter is usually somewhat lower1 because most commonly used drills provide an air cushion which slows the piston just before it comes in contact with the drill rod. Penetration rates for the two drills were determined in nine rock types, and the physical properties of the same nine rocks were measured and tabulated. Then the penetration rates were plotted against the individual properties to determine the general relationships on which methods for predicting drilling rates could be based.2

Jan 1, 1970

By Edmond S. Miksch

The morphology and growth rate of ice grown in supercooled water are markedly affected by convection of the water. A dendritic ice sheet with water flowing past the dendrite tip exhibits deflection of the dendrite spine toward the upstream direction, accelerated growth of secondary spines on the upstream side, and suppression 01" secondaries on the downstream side. Flow causes a thin disk to become corrugated, the corrugations being parallel to the flow. Flow causes an increase in the growth rate of the ice. IF a small seed of ice is placed in slightly supercooled water, it grows initially as a disk with the axis of the disk parallel to the c axis of the ice crystal.' It appears that growth in the c direction is inhibited, while growth occurs with equal facility in all directions in the basal plane. It appears that growth rate as a function of interface temperature is very nearly equal for all directions similarly oriented relative to the c axis. Subsequent to the discoid growth, branching occurs and dendrites develop. The primary dendrite spines grow parallel to the six equivalent a axes of the crystal. Secondary, and in some cases, tertiary spines also grow in these directions. The highly anisotropic: dendritic growth indicates that there must be some finite difference of growth rate for different directions in the basal plane. These differences must be quite small, however, since if they were large, the discoid mode would not occur. Hence, it was expected that the dendrite growth direction could be deflected from the crystallographic direction by perturbation of the thermal field at the dendrite tip. Experiments were done in which perturbation of the thermal field was accomplished by causing the supercooled water to flow past the dendrite tip. The flow direction was perpendicular to the c axis of the crystal, and was perpendicular to the primary spine of the unperturbed crystal. Supercooled water was supplied by a 15 cm cubical copper box, which was refrigerated and insulated so it could cool water to temperatures down to —2oC, and maintain the temperature constant to O.l°C for the duration of a run. A lucite channel of rectangular cross-section, 12 by 24 mm, was mounted horizontally in the box, with one end open so water could flow into it, and the other end leading out through the wall of the box to a length of tubing leading: to an orifice plate 123 cm below. cnunMn s MIKSCH, MemberAiMe, formerly Research Associate, Research Associate, Fig. l(b)—Vertical section of apparatus A horizontal cross-section is shown in Fig. l(a), and a vertical section is shown in Fig. l(b). Means for observing the ice are shown in Fig. l(a). Collimated light passes through the ice sheet and forms an image on the ground glass screen. A lucite box containing dry air was employed to prevent condensation. Ice of the desired orientation was provided by the seed holder shown in Fig. l(b). This device was made of lucite, and had a reservoir in which ice could be frozen by placing it in a freezer. This reservoir com-unicated with the outside only through a narrow gap between two sheets of lucite. The seed holder (after ice had been washed off its exterior) was immersed in the tank of supercooled water, the narrow gap terminating in a slot in the top of the flow channel. Ice growing through a thin water layer in the gap between the two sheets of lucite was oriented so its c axis was perpendicular to the sheets. This orientation is an application of a growth phenomenon2 which causes ice growing along a smooth solid surface in supercooled water to orient itself so its c axis is normal to the surface. After the ice grew into the channel, further orientation was necessary, since the direction of the a axis

Jan 1, 1970

By J. J. Thomas

THIS investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. FIG. 1.-STRESS-STRAIN DIAGRAM. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 2, 1921

By AIME AIME

A SPECIAL meeting arranged by the Petroleum and Gas Committee of the American Institute of Mining and Metallurgical Engineers was held on Tuesday and Wednesday, Sept. 21 and 22, in the Assembly Room of the American Annex Hotel, St. Louis, Mo. Preceding the first session on Tuesday morning, the members and guests were registered and presented with the usual Institute badges. The morning session was opened at 10:30 by Ralph Arnold of Los Angeles, Calif., Chairman of the Petroleum and Gas Committee. In his opening remarks, he suggested that the petroleum section specialize more and more on the technical problems of the oil industry and that an effort be made to enlarge the membership of the Institute among the technical men of the industry. The following program was presented : OIL FIELDS OF RUSSIA, by A. Beeby Thompson and T. G. Madgwick, of London, England. Presented by H. A. Wheeler; discussed by Arthur Knapp and R. VanA. Mills. This most comprehensive paper was one of what is hoped to be a series to be presented by some of our foreign members. It is by far the best description in English of the world-famous Baku and other fields of Russia.

Jan 1, 1920

By H. Reginald Hardy, Y. P. Chugh, Robert Stefanko

Many materials including rocks, ice, metals and their alloys, wood, etc., emit transient vibrations in the audible and subaudible range when stressed. In rocks, this phenomenon is referred to as "microseismic activity, " "rock noise, " or " seismo-acoustical activity. " In metals this phenomenon is often termed "acoustic emission." Each individual microseismic disturbance is generally referred to as a "microseismim" or an "elastic shock." The terms "microseismic activity" and "microseismim" will be employed exclusively in this chapter. Microseismic activity has been observed in many rocks loaded experimentally in the laboratory.1 The form of a group of typical microseismims is shown in Fig. 1. Quantitatively, the microseismic activity in rock under stress is most commonly described by the number of microseismims observed per unit time. This is commonly known as the "noise rate." The noise rate in general increases with increasing stress level and rises sharply just prior to failure of the material.2 The origin of microseismims is not well understood, but it appears to be related to processes of deformation and failure which are accompanied by a sudden release of strain energy. In a polycrystalline material, microseismims may originate at the micro-level as a result of dislocations or at the macro-level by twinning, grain boundary movement, or initiation and propagation of fractures through and between the grains. It is assumed that the sudden release of stored elastic strain energy accompanying these processes generates a stress wave which travels from the point of origin, within the material, to a boundary where it is observed as a

Jan 1, 1972

William P. Blake, TUCSON, Ariz. (communication to the Secretary): As one who in youth, now nearly half a century ago, had the privilege of participating in the initial explorations which have alreacly resulted, within a single lifetime, in the establishment and Development of a vast continental empire, so well described by Dr. Douglas, I may be permitted to supplement with some additional details the comprehensive sketch given in his paper. Before the War Department, in 1853, sent out the Pacific railroad exploring parties, Fremont had already made his memorable expeditions, exploring the Great Basin and the passes into California; Sitgreaves had traversed, from east to west, the Zuni and Moqui country; and, still later, Emory had examined the region along the boundary-line between the United States and Mexico. The services of these pioneers deserve to be mentioned in even an outline of the history of continental development. Concerning the five practicable railroad-routes, suggested in the Reports of Explorations aid Surveys," etc., as published

Jan 1, 1900

Ira B. Joralemon, one of the world's most noted mining geologists, died last year at the age of 91. "His long professional career," says Donald H. McLaughlin, chairman of the executive committee at Homestake Mining Co., "covered an epoch in the history of mining that was unique in its opportunities and achievements," adding that many mining companies (Bunker Hill, Bralorne Mining, Copper Range, Anaconda, Newmont, Phelps Dodge, Homestake, etc.) greatly benefited from Joralemon's experience and wisdom.

Jan 12, 1976

By J. A. Herbst, K. Rajamani, Y. C. Lo

In spite of potential theoretical and economic advantages of large-diameter ball mills, many manufacturers elect not to build them owing to what is perceived as an excessively large design risk. This is because traditional predictions for mill scaleup to large diameters are not always accurate. Alternative methods of analysis and scale-up are required. Recent studies have shown that detailed population balance models which account for important grinding subprocesses (grinding kinetics, material transport, and classification) are capable of predicting the performance of small- and intermediate-diameter mills (up to 4.3 m, or 14 ft) from small-scale batch tests. These same models are used in the current study to predict the performance of a "borderline "large ball mill (4.7 x 5.5 m, or 15 x 18 ft) at Asarco's Sacaton operation, a ball mill (5 x 5.8 m, or 16.4 x 19 ft) at Kennecott's Chino operation, and one of the world's largest ball mills (5.5 x 6.4 m, or 18 x 21 ft) at Cities Service Pinto Valley operation. Model parameters required for scale-up have been estimated in a 380-mm-diam (15-in.-diam) batch mill. Predictions are compared with the results of detailed plant sampling in the three plants. For the Sacaton and Chino operations, the error of the predictions was found to be less than 2.5%, while the corresponding error for the Pinto Valley operation was less than 2.7%. It is concluded that proper representation of the major subprocesses of grinding in the model equations is the key to achieving accurate scale-up. Of special importance is the need to account for the size distribution of the grinding media and the influence of the size distribution environment in the mill on grinding kinetics.

Jan 1, 1986

By S. Mukai, Y. Shah, T. Zshikawa, T. Wakamtsu

In order to recover coal concentrate of low ash and low iron content, the electrostatic separation of coal was studied. It is more successful in the corona discharge field to recover the coal concentrate of low ash and low iron content than in the field without corona discharge. The effect of humidity on the electrostatic separation of coal was then studied. From the experimental results, it was clear that the electrostatic separation was excellent in about 60% relative humidity of atmosphere. Thus, the separation of vitrite from coal is practicable by electrostatic separation. In recent years the demand for high quality coal containing low ash, low iron, and low sulfur has increased. To fulfill this requirement, a higher grade coal concentrate must be produced. Study on the electrostatic separation of coal has been performed for several years in the author's laboratory. From the results of this research, it was considered that the behavior of coal particles in the electrostatic field relates closely to the ash and iron content in coal. In the present paper, the electrostatic separation of coal in corona discharge field was studied in order to recover the high quality coal concentrate and then the effect of humidity on the electrostatic separation was investigated. PREPARATION OF COAL SAMPLES The coals from the Akabira mine, the Kushiro mine, the Miike mine, and the Oshima mine which are famous coal mines in Japan were used in this study. The ash contents of these coals are shown in Table I. From the results of the analysis of the coal samples by the Norelco X-ray diffractometer, it is recognized that the Miike coal includes mainly pyrite, quartz, kaoline, calcite, and epidote; the Kushiro coal: kaoline, quartz, and montmorillonite, and the Oshima coal: siderite, dolomite, and other substances. For the preparation of samples, the coarse pieces of coal were crushed to about 2 mm in diam and then ground in an agator mortar. The ground products were sieved and fractions of 10 — 14 mesh, 14 — 20 mesh, 20-28 mesh, and 28-35 mesh were prepared, respectively. APPARATUS OF ELECTROSTATIC SEPARATION The principal part of the apparatus of the electrostatic separation used in the experiments is shown in Fig. 1. In order to generate the corona discharge field, a needle-shaped electrode combined with a pole electrode is installed as the high tension electrode. In the case of investigating the effects of the humidity on the electrostatic separation of coal, the needle-shaped electrode was combined with a plate electrode instead of the pole electrode as shown in Fig. 2. The pole or the plate electrode was installed to promote the repelling of the charged particles by producing the electrostatic field between this electrode and the grounded roller. It seems to be very useful on the coal separation to install these combined high tension electrodes. SEPARATION OF COAL PARTICLES IN CORONA DISCHARGE FIELD The separation testings on the coal samples in the corona discharge field were performed by the apparatus as shown in Fig. 1. These experiments were carried out under the following conditions: feed size 20 — 28 mesh, room temperature, normal humidity and applied voltage 15-20 KV, and the combined electrodes including the needle-shaped electrode were negatively charged. The results of these testings are

Jan 1, 1968

By Richard P. Rothwell

The communication which I hare to lay before my fellow-members of the Institute, is no elaborate paper, nor the statement of any great discovery; it is simply the record of convenient methods of conducting topographical survey?, and of keeping the notes of the same; methods that have grown out of practical experience, and have saved me many a day's labor by facilitating office and field work, and at the same time secured a greater degree of accuracy than is obtained by the methods now in general use. I assume it as granted that no topographical map is worthy of the name, except it represent the elevations and depressions of the surface by means of horizontal or contour lines. In the Ordnance Survey of Great Britain, the contour lines are traced for every fifty feet vertical height, I believe, by running out the line with level and compass through all its meanderings on the surface; this, of course, is a very tedious, though accurate process, but " in the woods," where many of our surveys have to be made, it would be practically impossible. Some time ago, I made an extensive and quite elaborate topographical survey and contour map of the southern portion of the Cahaba coal-field, in Alabama, the object of the survey being to

By A. Rakshit, W. E. Kolb, Y. C. Kim

An IBM/XT microcomputer with 10 MB hard disk storage, together with automatic sensing capability of truck movements at several key locations in the pit, formed the core of this automatic truck dispatching system. System software is written primarily in MICROSOFT FORTRAN with supporting subroutines in MACRO assembly language. The software is designed to automatically monitor truck movement throughout the pit, to make heuristic assignments based on expected shovel availability and truck travel times, and to record production statistics. It is currently dimensioned to handle 50 trucks, 10 shovels, 10 dump sites, and three material types. Due to the lack of funds to purchase the necessary communications hardware, the work related to the automatic sensing of truck movements has not been performed to date. Otherwise, the system is fully operational on a realtime mode.

Jan 1, 1986

By E. Ackerman, L. Y. Tu, S. C. Sun

The use of ultrasonics in forming emulsions is not new. As early as 1927 Wood and Loomis' reported preparation of emulsions with ultrasonics. In 1935 Rschevkin and Ostrawskyz described the use of great ultrasonic power in producing fine emulsions of various oils and paraffin in water. Recently Oyama and Tanakahmployed ultra-emulsification to increase the effectiveness of sodium ethyl xanthate in flotation of chalcopyrite and galena. An emulsion is a two-phase system consisting of two incompletely miscible liquids, the one being dispersed as finite droplets in the other. The dispersed liquid is known as the internal or discontinuous phase, and the surrounding liquid is termed the external or continuous phase. There are two types of emulsions; one is oil-in-water (O/W) and the other water-in-oil (W/O). The word oil refers to the liquid other than water. Circumstances exist in which the emulsion type is not clearly defined, and the internal and external phases both contain portions of the opposite phase. This is said to be a dual emulsion. Among the many hypotheses', 6v proposed for the formation of emulsions, the Bancroft's adsorbed film or double interfacial tension theory is widely accepted. Bancroft ""educed that in the process of emulsification the interfacial tension between oil and water is lowered by the formation of an emulsifying film, which contains the adsorbed molecules and/or ions from the emulsifying agent and the two liquids.

Jul 1, 1955

By Y. Wang, M. M. Singh, H. L. Hartman

Knowledge of the state of stress at the bottom of a drillhole is of practical importance in rock drilling, since the induced stresses must exceed the strength of the rock in order to cause fracture. This note reports on a numerical method to determine the stress distribution at the bottom of a borehole induced by a static bit load and overburden and fluid pressures. The procedure adopted is similar to that for the plane-strain, discrete model employed by Harper and Ang.1,2 The rock medium is considered to be homogeneous, isotropic, and elastic-perfectly-plastic. METHOD OF ANALYSIS AND PROGRAMMING The discrete model adopted consists of two types of points: mass points and stress points. The configuration and numbering notation are depicted in

Jan 1, 1967

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By R. J. Hafsten, E. S. Davenport, R. A. Grange

THE influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,1 and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely retarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths, Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745°F. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245°F. (675°C.), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarse-grained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite-that is, at temperature levels above about 1000°F. (540°C.)-but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to be presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000°F. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. MATERIAL AND EXPERIMENTAL PROCEDURE The material investigated was a commercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent M0. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By G. D. Gemmell

Effects of solid-sdutidn alloying with titanium, molybdenum, and tungsten at concentrations up to 10 pct on the strength of pure columbium at elevated temperatures (mainly 2000°F) have been investigated by means of creep-rupture, hot-tensile, and hot-hardness testing and recrystallization studies. ThIS paper presents some results from the initial part of a study of the effects of alloying on the high-temperature strength properties of columbium. The elevated-temperature strength characteristics of pure columbium were first studied. Binary alloys of columbium with titanium, molybdenum, and tungsten containing 1, 5, and 10 pct of the solute elements were chosen on the basis of their high melting points, their known solid solubility in columbium, and results of separate oxidation-resistance studies of columbium alloys. EXPERIMENTAL PROCEDURE All the materials used were of highest purity. A typical analysis of the columbium is shown in Table I. Compositions of the alloys are also given in Table I. To evaluate the strength properties of pure co-lumbium and the alloys at elevated temperatures, creep-rupture, hot-tensile, and hot-hardness testing was done on recrystallized material. To prepare the pure metal and the alloys for these tests, 1- 1b buttons were made in a water-cooled copper crucible, inert atmosphere, tungsten arc furnace. Tapered ingots, 3 in. long, were made from these buttons by a skull-casting technique and these were machined to 1/2 in. diam, swaged to 50 pct reduction (pure columbium at room temperature, alloys at lowest temperature possible without cracking, generally in range 1100" to 1800°F) and heated in vacuum (lo-' mm Hg) for 16 hr at 2550°F for re-crystallization and homogenization. The resulting grain diameter was 0.1 to 0.3 mm. The 10 pct Mo alloy casting was not successfully swaged at temperatures up to 1800°F without cracking and was not included in the test program. Creep-rupture testing was done at constant load in vacuum on cylindrical specimens of 0.16 in. diam, using Instron capsules. The pressure at test temperatures was less than 10-1 mm Hg. Hardneas readings taken on the test specimen before and after testing were used as a check on possible gaseous contamination. Hot tensile tests in vacuum on cylindrical specimens of 0.125 in. diam were also made with Instron equipment at a strain rate of 0.067 min.-l. Hot-hardness measurements were taken with a unit constructed at the Du Pont Experimental Station. The test piece, supported on an alumina anvil, and the molybdenum indenter shaft with sapphire tip is heated in a platinum-wound furnace. The load applied to the pyramid indenter is measured by strain gages attached to a proving ring located outside the hot zone. In the measurements reported here the load was I kg. The tester operates in a vacuum of about 10"5 mm Hg and is capable of temperatures up to 1400°C.

Jan 1, 1960

By M. A. Steinberg, J. Wulff, R. Kamm

In a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described. In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. Circular-hole Grids and Analyses OF Radiographs Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in. centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1.125 in. in diam and the clearance between plungers and die wall was 0.001 in. The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value On an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1949

By C. W. Spencer, F. G. Hochgraf, R. F. Cheney

Columnar grained specimens of nickel, containing 0.25 pct Si and 0.22 pct Mn, have been exposed to liquid bismuth in the temperature range 670° to 1050°C. Under isothermal conditions the liquid penetration rate is constant. The activation energy for the process is 22,000 cal per g-atom. Small amounts of plastic deformation, introduced into specimens prior to exposure, increase the penetration rate. The slou. step in liquid film penetration is associated with a reaction which occurs at or near the leading edge of the film. Either transfer of nickel across the liquid-solid inteqace or diffusion in the grain boundary ahead of the liquid film is suggested. Aliquid metal, if brought into contact with the surface of an unstrained solid metal, will usually penetrate to some extent into the grain boundaries of the solid. Under isothermal conditions the extent of penetration after any particular time of exposure is related to the relative magnitudes of the interfacial tensions concerned.1,2 If the liquid-solid interfacial tension is less than one-half the grain boundary tension the liquid may penetrate at a relatively rapid rate for an indefinite distance into the grain boundary surfaces. If the liquid-solid interfacial tension is greater than one-half the grain boundary energy, liquid penetration occurs at a continually decreasing rate so that after the liquid has penetrated to a relatively short distance below the surface the process essentially ceases.3 Many observations of a qualitative nature concerning inter crystalline attack by liquid metals have been reported, for example, liquid bismuth upon copper,' liquid mercury upon brass,4 and liquid mercury upon nickel.' Scheil and Schessl determined the rate of penetration of liquid bismuth into the grain boundaries of hot rolled copper rod? At constant temperature, penetration rate was found to be independent of the depth penetrated, the rate in- creasing with increasing temperature corresponding to an activation energy of 20,000 cal per g-atom for the process. It was suggested that at lower temperatures the liquid travelled mainly along lines of three grain intersections while at temperatures greater than 1000°C essentially all grain boundary surfaces were covered. Recently, in a study of copper bicrystals having a common [loo] axis it was found that at 649°C bismuth penetrated 22, 25, and 63 deg boundaries while it did not penetrate 2, 12, 15, and 72 deg boundaries.' Elbaum reported that liquid gallium penetrates aluminum grain boundaries to a depth of 0.6 cm after 11 hr at 27°c.8 Assuming that the rate controlling step in the process was diffusion down the liquid film to the specimen surface, a diffusion coefficient of 10-5 cm2 per sec was calculated. This paper reports a study of the penetration of bismuth-nickel liquids into the grain boundaries of a nickel alloy, containing 0.25 pct Si and 0.22 pct Mn as principal alloying elements. The phase diagram

Jan 1, 1962

By T. A. El-Bassyouni, Paul Gordon

Grain-gvowth data in zone-refined aluminum and in dilute alloys of copper with this aluminum have been obtained. The amounts of copper added were from 4 to 400 at. ppm. It was found that in both the unalloyed aluminum and the alloys grain growth was characterized by a high value of n in the isothermal growth equation 6n = Kt The inadvertent presence of 1 at. ppm Fe in the alloys was found to he more potent in slowing growth than the purposely added copper. Possible rationalizations of these observations and their general relevance to the theoretical use of gvain-grozvth data have been discussed. Grain growth data of Winegard and his co-workers' on zone-refined tin and dilute tin alloys were analyzed with some success2 in terms of approximate theoretical equations for boundary migration.2-4 In view of this success, experiments were carried out in an effort to obtain similar data on zone-refined aluminum and on dilute copper-in-aluminum alloys. The results obtained were anomalous in several respects and could not be used to test theory. A discussion of these anomalies is presented here; they have been attributed to impurity effects and serve to emphasize the sensitivity of grain growth in general—and the particularly high sensitivity in aluminum—to impurities. The resulting difficulties in the theoretical use of grain-growth data are also discussed. EXPERIMENTAL DETAILS An aluminum bar was zone-refined and leveled by methods similar to those described previously.' The degree of purity obtained is indicated in Table The data in Table I were determined by mass-spectrographic methods through the courtesy of Mr. Thomas A. Johnson of AIAG Metals, Inc.* Three dilute copper alloys with this aluminum were prepared also by methods described previously.' The alloys contained nominally 4, 40, and 400 at. ppm of Cu, respectively (0.001, 0.01, and 0.1 wt pct). Each material was fabricated by swaging and rolling into a round bar about 1/4 in. in diameter with an annealed penultimate grain size of approximately 0.003 to 0.007 cm. In order to minimize preferred orientation the fabrication was carried out in several steps, each consisting of a reduction of about 40 pct followed by a recrystallization anneal. Annealing temperatures for the grain-growth studies were attained by the use of boiling liquids up to 213°C and molten metal baths at higher temperatures. Temperatures were controlled to within 1°C. Samples for measurements were cylinders about 3/4 in. long and 1/4 in. in diameter cut from the fabricated rods. In the interests of sample economy a single sample was used for the grain-growth measurements at each temperature. Each sample was, thus, annealed for several successive periods of time, the grain size being measured at each annealing period on a transverse surface exposed by

Jan 1, 1965