Search Documents

By D. O. Noel, E. B. Gebert, J. D. Shaw

It is, of course, expected that manufacture of the various metal powders should involve numerous methods adapted to the specific characteristics of the metals themselves. Several methods for powdering a particular metal may be available, but the physical characteristics of the powder as produced by the several methods may be quite different. In the final analysis, the application of the metal powder dictates the physical properties that the metal powder must possess, and this, to a very large extent, will determine which of several possible methods of manufacture is adopted. Sometimes powder of the same metal is produced by more than one method, each powder having specific characteristics that make it particularly suitable for its application. For purposes of classification, the various methods of powdering metals can be grouped as follows: 1. Machining. 2. Milling (by ball mills, stamps, attrition mills, etc.). 3. Shotting (pouring molten metal into water, air, etc.). 4. Granulation (by stirring molten metal while solidifying). 5. Atomizing (disintegrating by steam, compressed air, etc.). 6. Condensation of metal vapor. 7. Reduction of oxide powders. 8. Chemical precipitation. 9. Electrolytic deposition. 10. Sintering (for producing alloy powders). 11. Formation of an alloy followed by dissolving or otherwise removing one of the alloying constituents. Machining Turnings, cuttings, filings, etc., are, of course, produced as by-products in machine work of various kinds, and find certain applications as metal powders. For example, iron powder so produced is used extensively as a reducing or precipitating agent and as a constituent in certain hard-finish cements.

Jan 1, 1938

By H. M. Conger

Kaiser Steel Corporation's Eagle Mountain mine is located in the Colorado Desert, 60 miles east of Indio, California. Iron concentrates from the mine are shipped by rail 164 miles to the' Company's steel mill at Fontana, and also to Longbeach, California for export. Temperatures are typical of the lower desert ranging from a high of 120 degrees in the summer to a low of 25 degrees in the winter. The average, annual rainfall of about two inches comes mainly as cloudbursts during the summer months. From its inception, the Eagle Mountain mine has had the problem: of breaking its mine rock. Practices followed from 1949 until 1962 were very costly, did not produce uniformly good fragmentation, and were incapable of sustaining, high production. During this period, every conventional type of explosive was tried and found to be unsatisfactory for one reason or another.

Jan 11, 1965

By Joseph Hartshorne

The attention which this process has attracted, especially in Europe, has led me to believe that members of the Institute would be interested in a report of the progress which has been made in the year and a half that has elapsed since my paper on the subject was read at the Colorado Meeting of this Institute. As already described in that paper (Duns., xxvi., 380), this process is a modificatioii of the open-hearth steel manufacture, whether acid or basic, collsistillg essentially in the division of the charge between two furnaces, one of which is charged about two hours earlier than the other, and tapped into the other after the charge in the latter has become fluid, the slag of the first bath being removed from it during the transfer. This description still remains true as far as it goes, but further experience has demonstrated that circumstances will very materially modify the relation of the two furnaces to each other, and the character of the work done in each of them. The function of the primary furnace has become more clearly and entirely that of doing the rough work of desiliconiziug and dephosphorizing, while that of the second or finishing-furnace has become almost entirely that of decarburizing and finighing the heat. To indicate these developments and their results is the object of this paper. In order to avoid needless repetition, I shall try to accomplish part of this object by giving a short resume' of what has been published elsewhere on this subject since my former paper was read. This will at least enable those interested to study the matter for themselves from original sources. Since that time the following papers have been read and published: " The Bertrand-Thiel Process of Making Steel," by Percy C. Gilchrist (Cleveland Institution of Engineers, Session of 1896-

Jan 1, 1899

By J. K. Edgar

For a number of years the production and use of super-purity aluminum (better than 99.99 pct) has been steadily increasing. High-grade lots of. such aluminum show certain outstanding characteristics not found in lower grades containing principally silicon, iron and copper as impurities. One such characteristic is the so-called "self annealing," that is, the re-crystallization of the heavily cold worked metal at room temperature.' Interest therefore is aroused as to the effects of the impurities. It is well known that the amounts of silicon and copper which occur in aluminum of better than 99.95 pct are completely soluble, at least at elevated temperatures (above 200°C). Iron, on the other hand, is known to be fairly insoluble in solid aluminum. Thus, a knowledge of the limits of this solubility would he of considerable use in studying the characteristics of the high purity metal. All investigators have agreed that iron has very low solubility in solid aluminum. Rosenhain, Archbutt and Hanson2 reported traces of an aluminum-iron phase in the "purest samples of aluminum obtainable." Gwyer and Phillips3 reported that an iron constituent was visible under the microscope in metal containing ".0088 per cent iron." Roth4 found that in the solid state the solubility of iron in high purity aluminum was 0.01, 0.01, 0.017 and 0.022 pct at 225, 320, 500 and 600°C respectively. Dix5 working with alloys containing less than 0.03 pct impurities, concluded from microscopic and chemical analyses of eutectic areas that the eutectic composition was close to 1.7 pct iron. Dix placed the eutectic temperature at 65s°C. Archer and Fink,6 using high purity aluminum-iron alloys, found that the hypoeutectic liquidus intersects the eutec-tic horizontal at 1.7 pct. This is in fair agreement with the investigation of the aluminum-iron system by Gwyer and Phillips who placed the eutectic at 1.89 pct iron with a freezing point of 653'C. Preparation and Chemical Analysis oP Alloys Electrolytically refined aluminum (99.991 pct aluminum) and a high purity alumi-num-iron alloy (11.45 Pet iron) were used in the preparation of the alloys for this investigation. To aid in controlling the iron content of the experimental alloys, an alloy of lower iron content was prepared first from these materials. The high purity aluminum was melted and heated to about 700°C in a plumbago crucible coated with alundum cement and the aluminum-iron alloy was then added. The alloy was thoroughly stirred, fluxed and skimmed and then chill-cast into notch bars. The aIlalyses of the three materials are given in Table I. The alloys for the determination of the solid solubility of iron in aluminum were prepared by melting 600 g total of the aluminum plus the required quantity of the aluminum-iron alloy (No. 92531). These

Jan 1, 1949

By Richard P. Rothwell

At the Boston Meeting of the American Institute of Mining Engineers in February last, Mr. George W. Mansfield read an interesting paper on " The Electric Motor in Mining Operations," and he entered into the calculations of power required and cost of transmitting energy in great or small quantities to a considerable distance. I do not intend to go over this ground, or to enter into any discussion of the technical details of transmitting power by electricity, but merely to set up a milestone on the road of progress to show where we now are, how far we have come, and if possible

Jan 1, 1889

By E. H. Phillips, A. F. Keenan

6.2-1. Historical Development. Hammering on hand-held drill steel was the earliest type of percussion drilling. It was not until 1838 that Singer developed a steam-operated drilling machine that lifted a drilling bar and let it drop by gravity. J. J. Couch of Philadelphia patented the first percussion drill in 1849. His machine was a steam drill which literally hurled the drill bar at the rock and retracted it by means of a ratcheted wheel. Later J. W. Fowle added automatic rotation of the steel. In 1871, Simon Ingersoll patented a rock drill mounted on a tripod which permitted drilling holes at any angle, vertical to horizontal. Up to the turn of the century, percussion drills in use were piston-type drills. The drill steel was solid and attached to an extension of the drill piston. Hole cleaning was accomplished by the pumping action of the steel in the hole. Down-holes were drilled wet and cleaned with a blow pipe while up-holes were drilled dry, allowing the cuttings to drop out by gravity. The forerunner of our present hammer drill was the free-piston drill which was first patented in 1884, by Sargent. Because solid drill steel was used, it did not successfully clean down holes. J. G. Leyner solved the problem of applying the hammer drill principle to down-hole and horizontal-hole work in 1897. The key was to pass com- pressed air and water through hollow drill steel to clean the hole. Leyner's work on valves and rotation mechanisms increased the blows per minute of hammer drills from 300 or 400 up to 1800 and more blows per minute and made possible the first lightweight drilling machines. The development of automatic feeds followed. 6.2-2. Percussion Drills. TYPES OF DRILLS. There are two types of percussion drills in use today; the piston drill and the hammer drill. In the

Jan 1, 1968

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist-of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' lass because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

By Oren C. Baptist, Eliot J. White

Samples of four reservoir sands having different degrees of water sensitivity were subjected to several laboratory tests to determine differences in capillary behavior attributable to clay-mineral effects. The degree of water sensitivity was estimated by the difference between gas and water permeability. Unsaturated pore volumes determined with mercury injection were comparable to irreducible water saturations determined with the semipermeable bar-rier method only for the non-sensitive sands that contained small amounts of non-swelling clay minerals. Irreducible saturations were independent of salinity of the water, which suggests that most residual water is adsorbed 0.7 a film over solid surfaces and that internal retention by clay minerals is relatively insignificant. The water-sensitive sands imbibed water to higher saturations than did non-sensitive sands, and this result is believed to be a combination of the effects of clay minerals and preferential wettability; however, the relative importance of each of these effects is riot determinable. Thus it is concluded that the semipermeable barrier method is the best of the laborafory methods used for estimating formntion water .saturations in the sands studied. INTRODUCTION This investigation is a continuation of studies of the role of clay minerals in petroleum production in the Rocky Mountain area. Previous work has shown large differences in gas and water permeability in numerous reservoir sands; these water-sensitivity effects observed in the laboratory have been correlated with well behavior in the field, and the degree of water sensitivity imparted to reservoirs by the various clay minerals has been determined.'.' The effect of interstitial clay minerals on formation water3 saturations is not so well known. It has been reported that formation water saturations probably are higher in clayey than clean sands,' but this effect has not been evaluated in the laboratory, and the relative effect of the various types of clay minerals on formation water saturation has not been determined. The clay-mineral groups of most importance to this study and to petroleum production in general are kaolinite, illite, and montmorillonite. The minute layers of montmorillonite are loosely bound to one another so that water enters between them, causing great expansion of the particles. Kaolinite and illite do not exhibit interlayer hydration, but they do immobilize considerable amounts of water owing to their large surface areas, which are of the order of 15 to 97 m2/gm of clay.5 The four Wyoming sands used in this study were selected to represent a wide range of water sensitivities. These sands, with the number of wells and fields from which the samples were obtained, are: Second Frontier, five wells in two fields; Newcastle, six wells in one field; Tensleep, two wells in two fields; and Lower Muddy, five wells in one field. EXPERIMENTAL METHODS AND PROCEDURES Water-displacement data were obtained by the semipermeable barrier method," using both fresh water and brines having either 16,500 ppm sodium chloride or calcium chloride. A displacement pressure of 35 psi was found to be sufficient to obtain the practical irreducible water or brine saturation (IWS, IBS) in most samples. Mercury-injection data were ob-tained with equipment and pro-cedures similar to those described by Purcell.7 Exceedingly high pressures are required to attain complete mercury saturation by this method; however, since saturations in most samples change very little with large pressure increases above 1,000 psia, the maximum pressure used was 1,400 psia. To facilitate comparison of mercury-injection and water-displacement results, it is convenient to express mercury-injection data in terms of unsaturated pore volume. The abbreviation, (100 - SHg)min, is used to denote the pore volume unsaturated by mercury at 1,400 psia injection pressure. Gas permeabilities, ki, were deter-mined by the method proposed by Klinkenberg.8 Methods of determining types and amounts of clay minerals by X-ray diffraction analyses, as well as methods of determining water permeability, have been described previously.' The imbibition characteristics of

Jan 1, 1958

[ ]

Jan 1, 1938

By John J. Childress, Russell L. Cook

Stringent environmental regulations, which have limited the use of sludge ponds, coupled with the economic incentive to clean more coal or to add fine coal cleaning additions to existing preparation plants have increased the use of static thickeners in preparation plants. The Lamella Gravity Settler, sometimes designated Lamella Thickener, is a shallow depth sedimentation device which has been applied in a variety of industrial process and wastewater control projects in place of the conventional raked thickeners. This paper presents the theory and design of the Lamella Thickener, as well as describing the operating results from several full scale installations in a variety of Appalachian preparation plants.

Jan 1, 1979

By D. G. Westlake, E. S. Fisher

The habit planes for zirconium hydride precipitation in crystals of a zirconium have been determined at various hydrogen concentrations. The (10 • 0)planes are the predominant habit planes; some (10 • 5) and (10 -1) planes were observed after charging conditions which pevmitted formation of a surface layer of hydride. No platelets zrlere observed parallel to any of the twinning planes. Mechanisms for em-brittlement due to hydride precipitation are discussed. LANGERON and Lehr1 found, in 1956, that zirconium hydride precipitates in zirconium in platelets lying parallel to (10.0) slip planes. In 1960, Kunz and Bibbz reported observing the platelets in three different families of twinning planes, (10.2) {11.1), and {11.2), but never in the slip planes. The present study was undertaken to ascertain the cause of these seemingly contradictory results. EXPERIMENTAL Two specimens of iodide zirconium were used in the experiments. Specimen I was a single crystal, while specimen II contained three grains. Grain growth was accomplished by the technique of Lange-ron and Lehr. Three faces were ground on specimen I; the first was 2 deg from the (00.1) basal plane, a second was 2 deg from the (10.0) prism plane, and a third was 4 deg from the (12.0) plane. One face was ground on specimen II such that the poles of the surfaces of crystals A, B, and C were as shown in Fig. 1. After the faces were ground on 600 grit silicon carbide paper, they were chemically polished by dipping in a solution of 8 parts hydrofluoric acid, 50 parts nitric acid, and 50 parts water. This removed all cold worked metal from the surface. The samples were charged to various levels of hydrogen content by heating in hydrogen gas which had been purified by reaction with uranium powder. The various charging conditions are shown in Table I. Specimen I was heated to the reaction temperature at the indicated hydrogen pressure and allowed to react until essentially all the hydrogen was used up. Then the temperature was raised for homogenization. Specimen II was charged by making periodic addi-

Jan 1, 1962

By B. A. Joyce, R. W. Bicknell, R. J. Bennett, P. J. Etter

Epitaxial layers of silicon have been grown on single-crystal quartz and alumina by two types of chemical reaction the hydrogen reduction of trichlorosilane and b) the pyrolysis of silane. These reaction systems are described. The cqsfallography of the two systems, as determined by electron and X-ray diffraction, is discussed, and epitaxial mechanisms suggested. The electrical behavior is briefly considered, and the design and properties of field-evert devices fabricated in the epilaxial material are also discussed. RECENT work carried out in these laboratories" has shown that it is possible to obtain epitaxial deposits of silicon on single-crystal quartz and alumina. The purpose of this paper is to describe the method of preparation of these layers using both the hydrogen reduction of trichlorosilane and the pyroly-sis of silane, to compare the crystallographic behavior of films on the two substrates, and to present some initial results of the electrical behavior of silicon layers on alumina. The structural study has been carried out using electron and X-ray diffraction and electron microscopy. The electrical assessment has been made in terms of conductivity and mobility determinations by the van der pauw3 technique, and by measurements on metal-oxide-semiconductor assemblies. 1) FILM PREPARATION Both quartz and alumina substrates, approximately 1 sq cm in area and 0.4 mm thick. were prepared from slices cut parallel to within a few degrees of (11.0), (10.0), and (00.1), and polished mechanically down to about 0.3 p diamond grade. Chemical polishing of alumina slices, using phosphoric acid at elevated temperatures, has also been used; epitaxial silicon layers have been grown on these substrates, but the process is not entirely reliable, possibly because the large strain present in the Verneuil-grown alumina crystal affects the chemically prepared surface. The two reaction systems are fairly conventional and are described briefly below. a) Trichlorosilane-Hydrogen System. The apparatus is shown schematically in Fig. 1. The substrate was heated by induction, with a fused-quartz encapsulated graphite hemicylinder as susceptor. The procedure for carrying out a deposition was to heat the substrate to reaction temperature in a stream of

Jan 1, 1965

By H. L. Luo, P. Duwez, C. C. Chao

BY rapidly cooling alloys from the liquid state, it is possible to obtain solid solutions beyond the equilibrium concentrations, provided that the components are miscible in the liquid state. Typical such cases include CU-Ag,1 Pt-Ag,2 CU-Rh,3 nickel-base alloys with silicon, germanium, and tin,4 and cobalt-base alloys with silicon, germanium, tin, aluminum, and gallium.5 In the present note it is shown that terminal solid solutions can be appreciably extended in A1-Mg alloys. The alloys whose compositions are given in Table I were prepared by induction melting in tantalum crucibles under an argon atmosphere. Both aluminum and magnesium were 99.99 pct pure. Weight losses after melting were less than 0.2 pct for the aluminum-rich alloys and less than 0.4 pct for the magnesium-rich alloys. From these weight losses it was estimated that the compositions of the ingots after melting were accurate within 0.3 at. pct for aluminum-rich alloys and within 0.5 at. pct for magnesium-rich alloys. As indicated in Table I, the compound AuCd10 in which there is an ionic contribution to the bonding. The authors thank Dr. J. H. Westbrook of the Research Laboratory, General Electric Co., for arranging the supply of materials and for his interest. This investigation was supported by the U.S. Atomic Energy Commission under Contract AT(30-1)-1002, Scope I. some of the alloys were also chemically analyzed and the results confirmed the limits of uncertainty based on weight losses. Rapid quenching from the liquid state was achieved by techniques previously described.8,7 The principle of these techniques consists of propelling a small globule of liquid alloy (about 20 mg) onto a copper substrate. The thin foils easily detached from the copper substrate were analyzed by X-ray diffraction using a Debye-Scherrer camera 114.6 mm in diameter and either nickel-filtered copper Ka or iron-filtered cobalt Ka radiation. Since the back-reflection doublets were resolved, the wavelengths used in the computatioas were CuKal = 1.54050A and CoKa1= 1.78892A. Lattice parameters were obtained by extrapolation of the Nelson-Riley function, and the tables compiled

Jan 1, 1964

By H. F. Yancy

PooR results in coal washing and in ore concentration are sometimes attributed to the shape of the particles in the feed. It is well known that the shape of a particle influences its rate of fall in water. This is evidenced by the value of the constant C in the Rittinger equation for the velocity V of settling in water, V = C-D(d- z ), where C has the following values: 2.73 for roundish grains, 2.37 for long grains and 1.92 for flat grains. This report, which is based upon data obtained during the course of coal-washing investigations conducted by the U. S. Bureau of Mines in cooperation with the College of Mines of the University of Washington, gives the results of a method or procedure of screening in which the particles are separated into three shapes and shows the deportment of these shapes when coal is treated on a coal-washing table. The method consisted in first screening the coal with Tyler standard square-hole sieves, followed by screening tests of each of these products with screens of rectangular opening. For this purpose Tyler "Ton-Cap" screens were used; each square-hole product was subsequently sized with two Ton-Cap sieves so selected that their shortest dimensions were approximately 75 and 50 per cent., respectively, of the opening of the square-mesh sieves. For example: A product which is through 8 mesh (0.093 in.) and on 10 mesh (0.065 in.) is screened on slotted sieves which have openings 75 and 50 per cent. of the 0.065-in. opening in one direction and an opening of not less than 0.065 in. in the other direction. For convenience in discussion, the particles retained on the first slotted screen are termed "cubical"; those retained on the second slotted screen are termed "prismatic" and those passing the second screen are called "flat." (See Fig. 1.) The square-mesh screens separate particles according to two dimensions, length and breadth; the slotted screens divide them further according to the third dimension, or thickness. Prismatic particles have a mass of about two-thirds, and flat particles of about one-half, that of cubical particles of the same square-mesh size. The screen-

Jan 1, 1931

THE increased demand for titanium alloys with improved high-temperature creep strengths has stimulated interest in silicon as an alloying addition to titanium. Silicon is a potent solid-solution strength-ener and, if added in sufficient concentration and properly heat-treated, can also dispersion-strengthen titanium by eutectoid decomposition.' However, better understanding of the nature and distribution of the resulting silicide dispersion in more highly alloyed titanium matrices is necessary for the development of useful titanium alloys which utilize the latter strengthening mechanism. This note describes the chemical and crystallographic characteristics of the silicide phase as it occurs in a typical high-temperature near-a titanium alloy matrix. Several Ti-6A1-3Sn-3Zr a11oys containing various amounts of silicon ranging from 0.1 to 1.0 pct were melted as 10- to 20-lb ingots and processed into 1/2-in.-diam bar stock. The microstructures of specimens annealed at various temperatures were conveniently summarized by the (Ti-6Al-3Sn-3Zr)-Si pseudobinary phase diagram illustrated in Fig. 1. Comparison with the Ti-Si equilibrium diagram indicates the substitutional solutes (Al-Sn-Zr) increase the eutectoid temperature and decrease the a terminal solubility. Annealing at temperatures sufficiently high to dissolve the silicon in a ß solid solution and cooling rapidly enough to preclude coarsening generally produced a uniform dispersion of fine silicide particles, whereas annealing at temperatures near but below the ß transus produced relatively coarse silicide particles. Annealing in the limited a, plus 3 region produced a duplex coarse and fine silicide array. Several a-annealed specimens were examined by X-ray diffraction to determine the crystallographic identity of the precipitate phase. Copper Ka X-ray diffraction patterns of bulk specimens which contained 0.5 and 0.8 pct Si were virtually identical to that of the silicon-free Ti-6Al-3Sn-3Zr base alloy except for a slight shift in some of the high-angle diffraction lines. Apparently the silicide volume fraction was too low to be detected in bulk specimens. X-

Jan 1, 1969

By K. R. Evans

The deformation mechanisms occurring in polycrys-talline, commercially pure titanium and a Ti-8 pct A1 alloy have been investigated and compared to earlier results by Levine on high-purity titanium single crystals and by Conrad on commercially pure titanium. In accord with Levine, two consecutive deformation mechanisms are observed to exist below 500°K with the transition temperature between mechanisms, Tc, strongly dependent upon interstitial composition. T, is found to be 210°. 375° -430°, and 450°K for alloys A large number of investigations have been conducted to determine the rate-controlling mechanisms of plastic deformation occurring in fcc and bcc metals. Very few investigations of a similar nature have been conducted for hexagonal metals. In fact, until very recently, magnesium is the only hexagonal metal which has been systematically investigated for determination of the rate-controlling deformation mechanisms.1"3 From these investigations, it was concluded that basal slip below 420°K occurs by the intersection of forest dislocations,1'3 while for prismatic slip the Peierls mechanism is rate-controlling at low temperatures with interstitial compositions of 0.024, 0.42, 0.61, and 1.13 at. pct expressed in terns of oxygen equivalents. The low-temperature mechanism is found to be an impurity obstacle mechanism in contrast to Levine's earlier conclusion of the Peierls barrier. Measurement of the activation parameters for deformation and estimation of the force-distance profile of the obstacles show their retarding force to be effective over longer distances from the obstacle as the interstitial composition increases. and thermally activated cross slip at higher temperatures. 2 The potential technological importance of titanium alloys has prompted recent studies of the deformation and fracture characteristics of titanium and its alloys. 4-8 Levine' systematically investigated the low-temperature deformation behavior of high purity titanium single crystals oriented for either basal or prismatic slip. It was concluded that the Peierls mechanism was rate-controlling at temperatures below 210°K, while above this temperature an undefined mechanism was rate-controlling. Conrad 7,8 concluded from an analysis of the composition dependence of the critical shear stress at 0°K and measurement of the activation parameters that the low-temperature deformation of titanium is controlled by an impurity

Jan 1, 1969

By E. L. Estabrook

Oil companies operating in foreign countries have made increased use during 1930 of cooperative agreements in prospecting unproven territory and in developing proven territory. A considerable proportion of the existing foreign fields are held under single ownership and have been developed as units. The operating companies seek to maintain this condition by acquiring land in large blocks or by merging smaller concessions under unit operating agreements. Your committee has secured a number of reports on foreign non-competitive operations and a valuable formal paper which deals with the Golden Lane of Mexico.l 0. B. Knight has drawn some valuable comparisons concerning costs of development and ultimate production between a certain competitive area and another noncompetitive area along that strip of rich producing territory. After discussing details of production, numbers of wells and cost of drilling and production, he concludes that the 93,700,000 bbl. of competitive oil will have cost $0.193 per barrel as compared to 85,700,000 bbl. of noncompetitive oil at $0.059 per barrel. The saving of $0.134 per barrel amounts in round figures to $11,500,000, which is 21/2 times the total cost of developing the non-competitive block. The cost for drilling and development of the two areas of 3550 acres which Mr. Knight compares was $18,150,000 under competitive and $4,760,000 under noncompetitive conditions. The estimated ultimate production of the competitive 3550 acres is expected to reach 93,700,000 bbl., or 8,000,000 bbl. above the noncompetitive block. Under ordinary production methods it is to be expected that a noncompetitive area will yield less oil per unit area than will a similar competitive area, because of closer spacing and more rapid extraction in the latter case. The advantage of noncompetitive conditions, in this regard, is that the undivided ownership makes it possible to apply repressuring as a production method fairly early in the life of the field and thus, in the end, to vastly increase the yield. In the particular region described by Mr. Knight, repressuring is not thought to be a factor of

Jan 1, 1931

By Walter C. Smith, O. J. Seeds

METALLIC bismuth was known in the Middle Ages and the name is supposed to come from the German Wismut. The origin of the German name is uncertain. References to bismuth are found in the writings of Valentine, Paracelsus, and Agricola between 1450 and 1550. Early specimens of bismuth were very impure and often were confused with antimony, tin, and zinc. About the middle of the eighteenth century, J. H. Pott, C. J. Geoffroy, and Torbern Bergman succeeded in producing fairly pure bismuth and showed it to be an elementary metal similar in many respects to lead. H. S. Washington has estimated that bismuth occurs in the earth's crust about as abundantly as tungsten and silver; i.e., to the extent of 10-6 or 10-7 pct. It is found as native metal, both alone and associated with tin, copper, and other metals, and in a large variety of ores. The important ores are the sulfide (bismuthinite), the oxide (bismite), and the carbonates (bismutite and bismutosphaerite) . Other occurrences of bismuth are in the vanadate (pucherite), the selenide (guanajuatite), the telluride (tetradymite), and in many complex sulfides, arsenides, and antimonides. Bismuth minerals have been found in many parts of the world but very few of the bismuth deposits have been of economic value, the oxide ores from parts of China being the exception. The major portion of the bismuth production of today is the so-called by- product bismuth. Bismuth often occurs in ores mined and treated primarily for other metals, and during the treatment of these ores

Jan 1, 1953

By C. A. Pierce

STUDIES of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its com-mercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft. in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft, of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding for-mations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresses."1

Jan 1, 1938

By George Asmus

CLOSED front, or open front for blast-furnaces, has been for a number of years a much discussed question among the furnace-men in every country where iron is made. As blast-furnaces are costly structures, and as the whole question is one of economy, I hope to be excused for entering a little into details. The ('fore-hearth " is a prolonged opening in the lowest part of the hearth, from two to three feet wide, four to six feet long, and two to three feet high. It is a more or less fire-proof box, cooler than

Jan 1, 1876