Search Documents

By Tong Guangxu

INTRODUCTION Throughout the world, the caving mining methods of ore-draw under the overlying waste rock are sublevel caving in Sweden, block caving in U.S.A. and forced block caving and sublevel caving with sill-pillar in U.S.S.R. These caving methods are of high efficiency, low cost and large production (especially the block caving method) when compared to opencast mining. From the ore production of all under- ground mines, the largest annual production of underground metalliferous mines in the world is caving methods. The sublevel caving in Kiruna Iron Mine of Sweden has reached annual ore production over 20 million tons in 1974. The block caving in Climax Molybdenum Mine and San Manuel Copper Mine of U.S.A. both have produced about 40 thou- sand tons of ore per day in 1971. At the same time, the productivity of Kiruna was 12 thousand tons of ore per man-year, Climax 42.8 tons (48.3 short tons) per man-shift and San Manuel 29.01 tons (32.1 short tons) per man-shift. The main feature of this group of mining methods is the underground extraction of ore from beneath overlying caveable waste rock. Since the loss and dilution of ore are inherent (sometimes to a great extent), the control of ore-draw in these methods as com- pared with other methods is very important. Consequently, concerned Universities and Research Institutes have devoted great amounts of research on ore-draw theory and control management which has provided positive results to mine production, and has apparently promoted the development of the caving methods. During 1979 in China, metalliferous underground mines accounted for 15.22% of the total iron ore produced, while also accounting for 56% of total non-ferrous production. According to the mining methods, sub level caving in the principal underground iron mines counted for about 56.74% of total principal underground iron mine production, but only about 1% of total non-ferrous underground mine production. Relative to forced block caving and sublevel caving with sill pillar, the Chinese non-ferrous under- ground mines estimated about 35% of total non-ferrous underground mine production from these two methods, mainly from the latter. From the trend of development of underground metalliferous mines in China, the percentage of production in caving will be increased in the future, especially in block caving and forced block caving which have already been given great attention in the mining circle. In these types of mining methods the ore is drawn from the stope under a large area of overlying waste rock, which complicates the basic regulation and control of ore-draw, but provides lower loss and dilution than sublevel caving. Because of these reasons, the Kiruna Iron Mine in Sweden is intending to change its sublevel caving by testing a sublevel shrinkage caving method and considering a large area of ore-draw beneath the stope as an advantage. Therefore, the basic regulation and control management of ore-draw under a large area, as practiced in China, will be discussed in this paper. BASIC REGULATION OF ORE- DRAW FROM CAVING STOPE The aim of studying ore-draw under a large area of overlying waste rock is to se- cure a planned draw schedule that guarantees a certain plane of interface between ore and waste rock, and controls the change of its shape in spatial position for reducing ore loss and dilution during the draw process. Presently, the ellipsoid theory is comparatively near the actual attitude of ore-draw from the cave. 1. Ore Drawn Out from Single Drawpoint Laboratory testing and practical experience all show that after a certain amount of ore has been drawn out from a drawpoint, its original shape in the stope before drawing is more or less similar to an ellipsoid, hence the name "draw ellipsoid." This draw ellipsoid is cut at the bottom by a horizontal plane corresponding to the raise of the drawpoint, and its volume can be calculated by the following formula:

Jan 1, 1981

By C. N. J. Wagner, E. N. Aqua

Dilute Fe-Si alloys (0 to 5 wt pet Si) were cold-worked by making filings at room temperatuve. The analysis of the broadening of the X-vay powdev pattern peaks yields anisotropic particle sizes normal to the (110), (100), and (112) planes which are a consequence of deformation faults (probability a) and twin faults (probability p). The combined fault probability (1.5a +ß) increases from 0.01 in pure iron to 0.02 in Fe-5 pct Si. The root mean square stvains vary with crystallographic ovientation due to elastic anisotropy of the alloys, and increase from about 0.0035 in pure iron to 0.005 in Fe-5 pct Si measured in the [100] direction. Assuming that deformation and twin faults occur with equal probability, the X-ray data would imply that the stacking-fault energy does not change upon alloying. THE crystallographic aspects of the plastic deformation of dilute Fe-Si alloys has been studied many times since the observation of glide band structures by Barrett et a1.l These glide bands were much straighter than the wavy bands observed by Gough2 in unalloyed iron nearly 40 years ago. This difference in the morphology of the slip band structure has been verified many times, most recently by replication electron microscopy3 and dislocation etch-pitting methods.4,5 These observed differences in deformation behavior have been considered to result from the degree of cross slip that occurs in pure iron and in the Si-Fe alloys. The lowered tendency for cross slip would result from a lowering of the stacking-fault energy of iron by the silicon alloying addition. Experimental evidence for this lowered stacking-fault energy in the Si-Fe alloys, obtained with transmission electron microscopy, is the observation of dissociated dislocations in Fe-6 pct si6 and Fe-3 pct Si alloys,7 and the observation of sharply defined cellular substructures in Fe-3 pct si6,7 compared to the more diffuse substructure in zone-refined iron.' The activation energy for recovery of cold work is greater in the Si-Fe alloys than it is in pure iron, indicating that cross slip has become a more difficult process.9 The purpose of this investigation is to determine the change in stacking-fault probability from the broadening of powder pattern peaks in dilute silicon-in-iron solid solutions, when cold-worked at room temperature. The knowledge of the stacking-fault probability and the dislocation density, both of which can be deduced from line-broadening analysis of two orders of reflections from (110), (200), and (112) planes, will permit us to calculate the change in stacking-fault energy upon alloying silicon into iron. Previous X-ray investigation of cold-rolled Fe-5 wt pct Si (100)[001 ] single crystals did not reveal any line broadening, whereas cold-rolled Fe-3.1 wt pct Si (001) [110] and (001)[100] single crystals10 showed line bro2dening as a consequence of small particle sizes (-200A) and root mean square strains (-0.25 pct), which are comparable to those found in cold-worked iron filings.11 EXPERIMENTAL PROCEDURE A series of five Fe-Si alloys containing nominally 1 to 5 wt pct Si and pure iron were cold-worked by making filings at room temperature. The actual silicon content deviated at the most by +0.1 pct which is of no significance in the present study. The carbon contents of these materials were less than 0.02 pct. The X-ray diffraction patterns were measured with molybdenum, cobalt, and iron radiation using a GE and a Philips diffractometer. The (110)-(220), (200)-(400), and (112)-(224) pairs of reflections were

Jan 1, 1968

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The mechanical properties of Ti-C and Ti-C-0 alloys can be altered by heat treatments to dissolve or reject carbon from solid solutions. The maximum strength is obtained by annealing just below the peritectoid temperature. Quenching from the ß-carbide field results in softening. Impact behavior is influenced by the extent of solution of interstitials CARBON is not as important in titanium alloys as it was in earlier years when graphite induction melting was more prevalent. With induction melting, carbon pickup is about 0.5 to 0.8 pct. Cold-mold arc melting with graphite electrodes, which is among the more current methods, results in carbon pickup of 0.1 to 0.2 pct. The titanium-sponge melting stock itself contains about 0.02 to 0.07 pct C, picked up from the magnesium used in the reduction process. Thus, carbon is still one of the more important contaminants in titanium and needs careful study and evaluation in order to understand titanium and titanium alloys. Moreover, it is equally proper to consider carbon as an alloying addition because, in controlled amounts in titanium alloys, it may serve a most useful function. This is particularly the case where the ultimate in toughness is not required. The addition of carbon to titanium results in a peritectoid-type system as illustrated in Fig. 1. The solubility of carbon is seen to be higher in the a phase than in the ß phase in the temperature range of interest. Below the peritectoid temperature, the solubility of carbon in a titanium decreases with decreasing temperature. This type of system permits many microstructural and heat-treatment variations which may influence the properties of the alloys. The study of how the microstructure variations affect mechanical properties is described in this paper. Experimental Procedures The experimental techniques and testing methods used in this work were the same as those described in detail in a previous paper.' No further descriptions will be given except where changes have been made. High purity iodide titanium, produced by the New Jersey Zinc Co., was used in all of the alloys. Carbon additions were made using high purity spectro-graphic carbon electrodes in order to obtain the highest purity carbon available. The alloys were prepared by double arc melting to reduce the possibility of segregation. The alloys were forged at 875°C to ¾ in. round, descaled, vacuum annealed for 5 hr at 900°C to remove the residual hydrogen, and swaged to ¼ in. round at 750°C. All heat treatments were made on material in this initial condition. Two of the early Ti-C ingots were found to have been contaminated in melting. Vacuum-fusion analyses showed that the two contaminated alloys had picked up oxygen, so the test results on these two alloys permitted an evaluation of ternary Ti-C-0 alloys. A list of the alloys and their compositions are given in Table I. Properties of Ti-C Alloys In a peritectoid-type system, such as the Ti-C system, the chief microstructural variable which influences the properties is solid-solution strengthening. For a given composition, it is possible to control the disposition of carbon, either in solid solution or as the compound Tic, by suitable heat treatments. When in solid solution, the carbon present in the alloy makes a definite contribution to the strength of the alloy. However, when present as Tic, it has very little effect on the strength. Other microstructural variables considered in this investigation were transformation structures and grain size. As discussed in subsequent sections, these variables have only a minor effect on properties as compared to the solid-solution effect. Solid-Solution Strengthening: The principal strengthening mechanism for Ti-C alloys has been found to be solid-solution strengthening. Carbon in interstitial solid solution strengthens titanium, but has very little strengthening effect if present as the compound. Since carbon has a higher solubility in

Jan 1, 1956

By E. I. Alessandrini, A. U. Seybolt

Selective oxidation (preferential oxidation of a single alloy component) can be an important oxidation mode in the case of alloys such as Si-Fe, Al-Fe, and so on, when heat-treating in atmospheres of low oxygen potential. It was the purpose of this work to identify the oxide films formed on iron containing 31/4 pct Si at low oxygen potentials, and to make some observations on the H2O/H2 ratios required to form them. EXPERIMENTAL METHOD HYDROGEN of varying water content offers a very convenient method of establishing a wide range of oxidizing power, or oxygen potential. The method chosen to provide a desired H2O/H2 ratio was to nearly saturate hydrogen at room temperature by bubbling the gas through water at room temperature, and then to wring out the excess water by passing the wet gas through a long glass spiral immersed in a refrigerated liquid at a desired dew point. After oxidation, the samples were examined by electron diffraction in order to identify any film which might be present. PREPARATION AND TREATMENT OF SAMPLES The samples were prepared from a Si-Fe alloy made in the laboratory using electrolytic iron and 96 pct ferro-silico11, vacuum-induction melted, hot-rolled then cold-rolled to 0.015-in. thickness. After the cold-rolling the samples were annealed at 1000°C. Transmission Laue X-ray patterns showed very little evidence of preferred orientation, but it is likely that a weak texture could have escaped notice. The chemical analysis was as follows: 3.34 Si, 0.01 Al, 0.001 0, 0.006 C, 0.002 N. Before each sample was oxidized, it was polished through 4/0 emery paper, cleaned and dried using benzene, carbon tetrachloride, acetone, absolute alcohol, and ether. The method of oxidizing the samples was as follows: Samples about 1/2 by 1 by 0.015 in. were held in the upper, cool part of a vertical vacuum furnace until the desired temperature was established in the furnace, Fig. 1. The sample was then lowered into the uniform hot zone where it was heated quickly to the desired temperature, and subjected to hydrogen of controlled moisture content (dew point) as mentioned previously. Temperatures from 400" to 1000°C were used, and dew points from room temperature to —78°C were explored. In general, the runs lasted about 6 hr, but a few runs were of different duration, as will be indicated later. After the predetermined period of time had elapsed, the specimens were withdrawn by the hollow stainless steel-quartz holder to a cool zone at the top of the furnace. EXPERIMENTAL RESULTS The results are summarized in Table I. Most of the electron-diffraction patterns were obtained by glancing-angle reflection, but in a few cases it was possible to strip the oxide films from the surface by a total immersion in a 3 pct bromine-methanol solution. Some of the thinner stripped films yielded quite satisfactory transmission patterns. However, both diffraction techniques yielded the same results; the patterns while most frequently showing a (low) tridymite, also showed a (low) cristobalite in some cases. A few patterns showed evidence of both phases. Because of the known nonequilibrium behavior of silica, it is not surprising that both forms of silica could coexist on one sample. It was noted that at fairly low dew points such as —40°C, there was a tendency for diffuse diffraction rings, suggesting a very small crystallite size. Also some subsequent experiments to be reported later show that thin silica films can be amorphous.

Jan 1, 1959

By P. S. Martin, B. J. Guarnera

As an energy source, lignite is short on selling points-it contains large amounts of moisture and often large amounts of ash, resulting in low heat content. The moisture produces rapid oxidation upon exposure and self-ignition commonly occurs within two to three weeks, resulting in major transportation and storage problems. Nevertheless, as interest in alternate fuel sources increases, lignite deposits in the Coastal Plain of the US are attracting more and more attention. Two lignite mines are operating in Texas and additional developments are planned in that state, Arkansas, and Louisiana. At present, Texas lignite is burned only at mine-mouth generating facilities, but more exotic uses such as gasification are projected in the future.

Jan 4, 1979

By Carle R. Hayward

WHEN lead production began to recede from the peak productions of 1929 many plants took advantage of the curtailed operations to make necessary improvements and repairs about the plant. There followed a period of adjustment to synchronize production and demand, which merged in the present period of marking time. The lead smelting and refining industry has produced little that is new during the past year except in what might be called makeshifts, which have been introduced to make operation at fractional capacity profitable. This is more particularly true in refineries than in smelters. The Parkes process had become standardized during the period of normal production, with softening, desilverizing, and dezink-

Jan 1, 1935

By James E. Lawver, James L. Wright

This paper discusses the design and calibration of a Faraday pail for measuring electric charge. The paper also shows that at least for two minerals, quartz and calcite, the phenomenon that Johnson termed "reversibility" can be explained in terms of the contact electrification between the minerals and the metal rotor of an electrostatic machine. Each year the free world produces about 13 million tons of mineral concentrates by electrical separation. However, despite the rather general acceptance of electrical concentration as an industrial process, research in this area has lagged far behind the efforts devoted to competitive processes such as froth flotation. The purpose of this paper is to describe the design and calibration of a Faraday ice pail for measuring charge density on mineral grains and to show some of its applications in the area of electrostatic and electrodynamic research. THE DESIGN AND CALIBRATION OF FARADAY PAILS FOR ABSOLUTE CHARGE MEASUREMENT The electric charge on mineral grains at a given time during an electrical concentration process is de- pendent on many factors and cannot, in general, be accurately calculated a priori. It is thus important to devise a method of measuring absolute charge. One method of measuring electric charge is to note the potential rise of an electrometer when charged particles drop into a Faraday pail. Two types of Faraday pail have been constructed and calibrated. The first type, Faraday Pail I (Fig. 1), is a vertical pail originally designed to measure the charge due to contact electrification between mineral grains and a metal rotor or due to conductive induction when mineral grains are passed over a rotating cylinder in the presence of an electric field. The second type, labeled Faraday Pail II (Fig. 2), is a horizontal pail designed to determine the charge distribution of mineral grains after they pass through the separating zone of the electrical concentrator shown in Fig. 4. The main advantage of the horizontal pail is its low head-room requirement and the long opening which enables the experimenter to sample the entire width of the stream of minerals being separated. The Faraday pails were calibrated in the following manner: A calibration head was constructed in the form of a hollow brass sphere that could be held in an insulated metal cylinder by vacuum (Fig. 1). The capacitance of the sphere was calculated by measuring the capacitance of the sphere and cylinder combined and that of the cylinder alone and subtracting the latter measurement from the former. The sphere was then charged to a known potential (V) and allowed to drop into the Faraday pail which was attached to a Keithley Model 610A electrometer. This instrument has an accuracy of 2% full scale and has

Jan 1, 1969

By T. E. Leontis

The specific effect of various rare-earth metals on the room- and elevated-temperature properties of magnesium has been evaluated. Alloys containing didymium exhibit the highest tensile and compressive strengths at room and elevated temperatures. All the rare-earth metals increase the creep resistance of extruded magnesium at temperatures in the range of 400° to 600°F, but the degree of enhancement depends on the temperature and on the concentration of the added metal. THE effects of rare-earth metals on the properties of sand-cast magnesium were discussed in some detail in earlier paper by the author.' The present paper deals with the effect of the same alloying elements on the properties of extruded magnesium. This investigation also had as its aim the development of a wrought alloy having a better combination of room-temperature strength and ductility and elevated-temperature strength and creep resistance than is found in magnesium-Mischmetal-manganese alloys, which have been reported earlier.2-5 The only known attempt to study wrought magnesium alloys containing pure cerium instead of Mischmetal was made by Mellor and Ridley.6 They found that in the form of rolled bars there is a definite, optimum cerium content for creep resistance at 200 °C and that the creep resistance of these alloys at 200 °C is significantly Improved by heat treatment at 550" to 580"C. In the present investigation the compositional variation in mechanical properties of the following alloy systems is presented: I—magnesium-Misch-metal. 2—magnesium-cerium-free Mischmetal. 3— magnesium-didymium. 4—magnesium-cerium. 5— magnesium-lanthanum. Alloys containing predominately praseodymium are not included in this series because of the lack of this material. Experimental Procedures The alloying ingredients used in preparing the alloys described herein are the same as those reported in the earlier paper.' Cerium-free Mischmetal is the rare-earth mixture remaining when the cerium is removed from Mischmetal, which contains all the rare-earth metals as they occur naturally in mon-azite sand, the ore from which Mischmetal is produced. Removal of both cerium and lanthanum from Mischmetal leaves what is commonly called "didym-ium," consisting predominantly of neodymium and praseodymium. Although the composition of the particular batch of each metal used may differ somewhat from the analysis presented previously, these differences are not great enough to warrant repeat- ing the specific composition of each material. The electrolytic magnesium used as the starting material in these alloys has the same typical analysis as that given in the earlier paper.' The alloys were prepared in small laboratory melts applying all the necessary precautions for alloying rare-earth metals with magnesium described by Marande.' Most melts were large enough to cast one 3 in. diam billet 10 in. long. In a few cases, particularly the didymium-containing alloys, the lack of sufficient amounts of the rare-earth metal limited the size of the billet to 6 to 8 in. All billets were scalped to a diameter of 2 15/16 in. and faced to a length of 9 ¼ in. as limited by the size of the extrusion container. The alloys were extruded into ½ in. diam rod on a 500-ton direct-extrusion press using a 3 in. container. The details of the extrusion step are: billet preheat, 925°F (2 hr); container temperature, 900°F; die temperature, 900°F; extrusion speed, 10 ft per min; reduction ratio, 36:1; and percent reduction, 97.3. The lower melting point of alloys containing didymium' necessitated reduction of the extrusion speed to 5 ft per min in order to prevent hot shorting during extrusion. Adequate lengths were cropped from both ends of each extruded rod to assure that all the material used for tests was extruded under uniform conditions. Tensile and compressive properties at room temperature are reported in the several conditions of heat treatment. The ASTM designations are used to distinguish these conditions as follows: T5—Direct age at 400°F (16 hr) T4—Heat treat at 950°F (4 hr) for alloys containing didymium T4—Heat treat at 1050°F (4 hr) for all other alloys T6—T4 + age at 400 °F (16 hr) The lower heat-treating temperature for alloys containing didymium is necessitated by the lower melting point of these alloys. All heat treatments were conducted in electrically heated, circulating-air furnaces. A protective atmosphere containing 0.5 to 1.0 pct sulphur dioxide was used for the high temperature heat treatments. Tension and creep specimens 6 Yz in. long and compression specimens 1½ in. long were cut from the extruded rod. A reduced section of ? in. diam was machined on the tension specimens, whereas on the creep specimens a reduced section of 0.450 in. diam

Jan 1, 1952

Jan 1, 1882

By Carel Robinson

THE little coal mine at Otsego, in the Winding Gulf field of southern West Virginia was dying. In the history of coal mining thousands of mines have been successful at first, but usually a change occurred and profits ceased. Often be change was so gradual and extended over such a length of time that the fundamental causes did not stand out in sharp relief and their significance was not realized. Studies often reveal that the cause for failure was in the arteries that connect the producing places with the mine entrance. Profits continued so long as the working places were close to the tipple and while the thrill of newness aid ease of access resulted in effective supervision from day to day. The air- way and haulageway, the wire line and manway, may have been sufficient when the distance from the entrance was a few hundred feet, but were inadequate when this was extended for thousands of feet.

Jan 1, 1937

By R. F. Mehl, G. T. Horne

Diffusion coefficients and mobilities were determined as functions of concentration in the a phase of the Cu-Zn system. Use was mode of incremental diffusion couples to determine the Kirkendall effect at various concentrations. Darken's analysis was used to calculate the individual diffusion coefficients and mobilities from these data. The general diffusion coefficient is a single-valued function of the concentration in this system to within the limits of accuracy of the experimental methods used. The form of the various functions (diffusion coefficients and mobilities) of concentration is the same in every case: it is essentially the same as the usual D vs c curve. AS Darken' has pointed out, the knowledge that the movements of different atoms diffusing in the same lattice need not proceed at the same rate is old. Ionic lattices are the classical examples; application of the generalization to lattices with metallic bonding was much more slowly accepted. It remained for Kirkendall'' to show clearly that metallic diffusion need not be symmetrical with respect to both species. Several investigators" have confirmed the initial observation of a "Kirkendall effect:" marker movement accompanying diffusion. They have extended it to other systems and conditions. The theoretical interpretations have been many; ne of the first and simplest of these is that of Darken"' which is essentially mechanism independent. Darken has shown that the Kirkendall experiment permlts a calculation of the individual diffusion coefficients and, coupled with activity data, offers a means of measuring the mobilities of the separateatoms in a binary diffusion process. There is no published information on the effects of concentration and temperature on the individual diffusion coefficients or on the mobility values in binary solid solution; this paper provides such information for zinc and copper in a brass. For purposes of clarity, the overall D value obtained, for example, from the Boltzmann-Matano solution to Fick's law, will be designated as the "general diffusion coefficient;" and the diffusion co- efficients for the separate diffusing species will be designated as the "individual diffusion coefficients." Experimental Procedure The authors have accepted Darken's analysis and have measured mobilities on this basis. The findings of da Silva and Mehl are accepted: that the Matano interface, defined as the origin of coordinates for the Boltzmann-Matano solution to Fick's law, coincides with the original weld interface; that the "shift" of a marker is the distance between the Matano interface and the marker; that the observed porosity is too small sensibly to affect this result; and that the shift is a linear function of the Matano area, the area defined as the absolute magnitude of the area on either side of the Matano interface. Alloys: The a-phase of the Cu-Zn system was chosen for investigation. The measurements were made on incremental couples for two separate reasons: l—it has been questioned whether D, the general diffusion coefficient, is a single-valued function of concentration (a comparison of the D-values for couples with small concentration range, e.g., 10 vs 20 pct Zn, against those from a wide concentration range, e.g., 0 vs 30 pct Zn, will answer that question); and 2—on the Darken analysis, the mobility can be determined only at the concentration at which the marker is observed to lie (this is but one concentration in a single couple) but choosing a series of incremental couples in the range between 0 and 30 pct Zn provides mobility values at several concentrations, thus giving mobility as a function of concentration. Four alloys were chosen; nominally, pure copper, copper with 10 pct Zn, copper with 20 pct Zn, and copper with 30 pct Zn. This allowed six different types of diffusion couples to be prepared, promising mobility determinations at six different concentrations, but having a minimum range of 10 pct Zn. The copper was an especially prepared pure copper supplied through the courtesy of the Ameri-

Jan 1, 1956

By Jean Howard

ThE formation of the (100) [001) texture in 3-1/4 pct Si-Fe strip was first reported by Assmus ef a1.l in 1957. Since then much experimental work has been carried out with a view to establishing the mechanism involved. The papers cited above state that the (100) [001] texture was developed in strip rolled from material melted and cast in vacuum. (The impurity content of the ingot is reported as 0.005 pct.) The present note records that similar results can be obtained in material processed by powder metallurgy. A processing schedule is described.which enables the texture to be formed in strip up to 0.010 in. thick, but there seems no reason why this should not be achieved in thicker strip, provided that large grains are developed after sintering. The materials were prepared from Carbonyl Iron Powder Grade MCP (particle size 5 to 30 p) of the International Nickel Co. (Mond) Ltd. The powder contains about 0.15 pct 0, 0.01 pct C, 0.004 pct N, <0.002 pct S, $0.005 pct Mg and Si, and 0.4 pct Ni— that is, it is substantially free from metallic impurities other than nickel, which is thought to be unimportant in the present work. The silicon powder was 99.9 pct purity, or material of transistor quality (ground in pestle and mortar). The mixed powders (3-1/4 pct Si to 96-3/4 pct Fe) are heated in hydrogen at 350" and 650°C to deoxidize the iron before sintering loose at temperatures between 1350" and 1460°C (depending upon the ultimate thickness of strip required) for up to 24 hr. The object of the high-temperature sinter is to develop a large grain size at this stage. Alternatively, the loose sintering can be done at a lower temperature followed by rolling or pressing and then annealing at temperatures between 1350" and 1460°C. Both methods produce large grains, which remain large throughout the process. The compact is then hot-rolled to approximately 1/8 in. with high-temperature interstage anneals if necessary. This step is taken to avoid intercrystalline cracking which would occur if the material of such large grain size were cold-worked. The bar is then annealed at 1050°C and reduced to its final thickness by approximately 50-pct reductions and 1050°C interstage anneals. Throughout the process the dew point of the hydrogen furnace atmosphere is maintained at about -40°C. Samples were annealed in hydrogen at various temperatures and times. Secondary recrystalliza-tion to (100) [001] was developed on the thinner material (i.e., up to 0.002 in.) by annealing in hydrogen at 1050" to 1200°C with a dew point of - 40°C or in vacuum (10-5 Torr) at 1050°C. With the thicker materials (i.e., up to 0.010 in.) the best results were obtained by annealing in hydrogen at 1200°C with a dew point of - 55°C. Complete secondary recrystal-lization to (100) [001] textures was obtained. Above these temperatures secondary recrystallization to (110) [001] tended to develop. The final annealing of samples was normally carried out with the samples placed between recrystal-lized alumina plates, but some experiments were performed with the samples suspended so that their surfaces were not in contact with anything except hydrogen, and these were equally successful in developing secondary crystals. An approximate determination of the proportion of material (before secondary recrystallization took place) having crystals with the (100) or (110) planes in or near the rolling plane showed that 11 pct of the sample had (100) and 16 pct (110). The method used for the determination is described below. A sample was annealed at a temperature just below the secondary recrystallization temperature and etched to reveal the (100) planes. The approximate area covered by crystals having (100) or (110) in or very near the surface was measured on the screen of a Vickers projection microscope. This was repeated for twenty positions chosen at random and a mean of the results calculated. The main hindrance to developing the secondary crystals in the thicker materials was the difficulty of obtaining a large enough initial primary grain size before secondary recrystallization. This was overcome by increasing the particle size of the silicon powder used. During the course of the work, it had been observed that the larger the grain size after sintering the more likely it was that the material would be successful in developing secondary crystals at a later stage. An experiment was therefore carried out to determine whether the material with the larger grain was more successful in developing secondary crystals due to the large grain produced at the sintering state per se or whether it was due to the greater reduction of silica brought about when the sintering temperature was raised in order to increase the grain size. A comparison was made between two compacts, one of which was made with silicon powder of 60 to 100 mesh, the other with silicon powder which was finer than 200 mesh. F?r this experiment, use was made of a phenomenon previously observed that the larger the particle size of the silicon powder employed in making a compact, the larger is the grain size of the compact. The silicon powder was ground

Jan 1, 1964

By F. G. Tahmoush, N. J. Grant, E. P. Abrahamson

The effect of grain size on the brittle -ductile transition temperature of pure iron and three dilute Fe-W alloys has been investigated by slow bend tests. The brittle-ductile transition temperature for pure iron increased with increasing grain sizes from 8000 to 500 grains per sq mm where the transition temperature then decreased with further increase in grain size. The dilute additions of tungsten lowered the transition temperature for fine grain sizes, suppressed a reversal of the curve in the coarse grained portion, and raised the transition temperature for this region. The frequency of twin occurrence increased with increasing grain size and decreasing temperature. The object of the present investigation was to re-examine the effect of grain size on the brittle -ductile transition of pure iron and several dilute Fe-W alloys. Current literature normally presents a simple relationship between grain size and the brittle-ductile transition temperature, namely, that the transition temperature increases with increasing grain size. Heslop and etch&apos; have studied the transition temperature of mild steel by V-notch Charpy impact tests for the grain size range between 200 and 6000 grains per sq mm. The result was a linear plot of In 1-1/2 vs brittle-ductile transition temperature, where 1 is the grain diameter. Recent experiments by sipos2 revealed the possibility of a reversal in the slope of the grain size vs transition temperature plot for pure iron; however, his investigation was limited in scope, and the data obtained were insufficient to permit a definitive curve. The present investigation was undertaken in an effort to confirm or extend the grain size effect observed in iron by Sipos. PROCEDURE All alloys were vacuum induction melted, using 99.95 pct Fe containing 0.03 pct 0 and 0.004 pct C. Four ingots were made, ranging from pure iron to iron with 0.035 pct W. The chemical composition of each alloy, after processing, is given in Table I. The four alloys were prepared as 45 lb heats and cast into 4 in. diam by 16 in. molds. They were then extruded into 3/4 in. rods at 1800oF. Specimens for chemical analysis, taken from various positions along the rods, revealed no variation in tungsten content along the length. The extruded rods were reduced to 0.156 in. diam stock by a series of cold swaging operations involving intermediate vacuum annealing treatments. This procedure yielded a final cold reduction in area ranging from 10 to 90 pct. The swaged rods were chemically cleaned, cold pressed to a cross section of 0.10 by 0.18 by 1.0 in. long (2.54 by 4.73 by 25 mm). The specimens were wrapped in iron foil and vacuum sealed (10-4 mm Hg) in quartz. Various heat treatments at temperatures from 700" to 1300oC were utilized to produce grain sizes from 8000 to 1 grain per sq mm. Grain sizes were determined by measuring the average area of grains in a polished section. In specimens with grain size greater than 20 grains per sq mm, the total number of grains in the cross section was counted and then divided by the area to yield grains per sq mm. Grain size was measured both for longitudinal and transverse cross sections. The average of the two measurements was plotted vs transition temperature. An Instron Table Model testing machine was used to determine the transition temperature of specimens tested in three point horizontal bending. The specimen was supported by two 1/4 in. dowels one in. apart. Bending was accomplished with a push rod, the end of which had an 1/8 in. radius. The head speed was 50 in. per min. Temperatures were established through the use

Jan 1, 1963

By J. Chipman, N. J. Grant, H. L. Bishop

In a recent review1 of the iron-oxide activity of simple open-hearth type slags containing lime, magnesia, silica, and iron oxide, it was established that activity values were lacking in the range of slag composition most interesting to open-hearth operators. That is, laboratory experimental results were not available for simple slag compositions having basicity ratios ranging from about 1.5 to 4.0 and iron-oxide concentrations ranging from about 10 to 30 pct. However, in order to estimate iron-oxide activities for the range of slag compositions of interest to open-hearth operators, activity values were calculated using ionic concepts of slags by following the treatment of Flood and Grjotheim.2 A study of these data indicated that the desired slag compositions were probably not obtained due to the limited solubility of the basic constituents lime and magnesia. Thus, it was decided to make additional heats equilibrating molten carbon-free iron with slags containing MnO, P2O5, and A12O3 in percentages commonly found in open-hearth refining slags, and to examine the liquid slag field over a greater composition range than that of the simple slags studied previously. The ranges of the constituents used in the present study are summarized as follows: Metal Pct 0 0.070-0.201 PctMn 0.005-0.142 Slag Pet CaO 24.45-41.90 Pct MgO 3.23- 9.21 Pct MnO 1.13- 9.62 Pct FeO 20.08-48.7 Pet Fe2o3 2.23-10.14 Pct SiO, 3.51-28.50 Pct P2O5 0.23- 3.65 Pct A12O3 0.43- 3.38 The experimental procedure consisted of equilibrating the slag and metal in an induction furnace provided with a carbon-arc slag heater as described previously by Winkler and chipman.3 The data obtained were used to establish both the iron-oxide activity values and the activity coefficients for FeO and MnO in the open-hearth type slags. RESULTS AND DISCUSSION I) Iron-Oxide Activity of Open-Hearth Type Slags—The iron-oxide activities of various iron-oxide contents of the open-hearth type slags, as calculated from the oxygen content of the metal by the method of Taylor and Chipman, 4 are plotted against the molar ratio of bases to acids in Fig. 1. The data represent slag-metal studies carried out in the temperature range 1530" to 1700°C. For the purpose of this study, the constituents CaO, MgO, and MnO are assumed equal on a molar basis in their effect on the iron-oxide activity; and, PO2,5 is calculated as an equivalent to SiO2 and A12O3 on a molar basis. The total iron content of the slag is calculated to FeO and is represented by the symbol (FeO) The points presented in Fig. 1 represent the results of this investigation for iron-oxide slags containing between 1 and 8 mol pct MnO and less than about 2 mol pct each of A12o3 and PO2,5 The curved lines shown in Fig. 1 represent the results of the summary1 of the iron-oxide activities of simple slags of the system (CaO + MgO) - SiOz - (FeO),. The solid portions of the curved lines represent experimental data, and the broken portions represent iron-oxide activities calculated from ionic concepts of slags. The iron-oxide values of the open-hearth type slags of this study are in good agreement with the values of the simple iron-oxide slag system. Only a slight modification is indicated. The results of this study suggest that the line for 20 mol pct (FeO), should be lowered slightly in the basicity range 1.5 to about 3.

Jan 1, 1959

By B. E. Field

COBALT is a silvery white metal with a slight bluish cast, strongly resembling nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ quite decidedly in their properties from those of nickel. The name cobalt was derived from the German "Kobold" meaning goblin and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was only isolated about the middle of the eighteenth century by Brandt although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470. The metal is fairly hard, with a density when pure of 8.81 in the cast state and 8.92 after working. The com¬mercial grade of cobalt has a density of about 8.75 in the cast state. The atomic weight is 58.97. The Brinell hardness of the pure metal is 124; that of the commercial grade varies from as low as 100 to as high as 138, depending upon the impurities present. Pure cobalt has a sharp melting point at 1478°C. The tensile strength of the pure metal in the cast condition is said to be higher than that of any other pure metal. Kalmus gives it as 34,400 lb. per sq. in. for cast unannealed metal; the effect of annealing at 850 to 900°C. is to raise the strength slightly. The yield point is close to the ultimate strength and the reduction in area and elongation are both low. Mechanical working raises the tensile strength of pure cobalt rapidly and in the form of wire it will be over 100,000 lb. per sq. in. The presence of small quantities of carbon in the commercial metal raises the tensile strength to as high as 61,000 lb. per sq. in., the reduction in area and elongation being raised at the same time to approximately 20 per cent.

Jan 1, 1933

By R. R. French

Investigations were conducted by the lndiana Geological Survey for some dry methods of bene-ficiating low-grade gypsum ore. Seventy-two batch and continuous flow tests were performed with a roller mill, rod mill, pebble mill, electronic color sorter, electrostatic separator, and an air separator. Approximately 650 size analyses and 550 chemical analyses were performed during the investigation. Batch samples were tested by the Survey, and most of the continuous flow tests were handled by com-mercial laboratories. INTRODUCTION Although many companies producing gypsum have been interested in dry beneficiation, very little information has been published in the past. One of the most comprehensive investigations was reported by the Canadian Department of Mines.5 Other reports of interest have been published by the Canadian Department of Mines,&apos; the South Australian Department of Mines,2 and the U.S. Bureau of Mines.3 Some beneficiating practices, such as hand picking, selective mining, crushing and screening, milling, and air classifying, were already in use in the Canadian industry prior to MacPherson&apos;s investigations.5 MacPherson examined the effect of tabling, air separation, screening, flotation, electrostatic separation, calcining, washing, and various types of milling, in his efforts to eliminate dolomite, limestone, and small amounts of silica and clay from the gypsum ore. RAW MATERIAL Gypsum and anhydrite occur within the lower part of the St. Louis Limestone (Mississippian) in southwestern Indiana. Gypsum in single beds 10 or more ft thick occur at Shoals, Martin County; near Freedom, Owen County; near Bloomfield, Greene County; and in the Devonian strata of LaPorte County. Only the Shoals deposit has been exploited commercially. The western edge of the Shoals deposit is contaminated by a continuous bed of shale, about 1 1/2 to 2 ft thick, near the top of the evaporite and by thin continuous strata or irregular masses of carbonate rock. The low-grade material used in these investigations was obtained from the waste pile of the National Gypsum Co.&apos;s plant at Shoals. The waste ore averaged about 67.4% gypsum and was contaminated by various amounts of shale, dolomite, and limestone. All the material had been previously crushed and screened to minus 1 1/4 to plus 3/8 in. X-ray analyses of powdered, sedimentated, gly-colated, and heat-treated samples of the shale showed that it was composed of slightly structurally disordered illite, Fe-rich chlorite, and very finegrained disseminated silt. The clays and silt were partly cemented with carbonate material. Light-gray argillaceous limestone and gray or brown porous dolomite made up most of the carbonate rock contamination. Crushing Characteristics: The rate unweathered gypsum, carbonate rock, and shale reduce in size was determined by crushing handpicked samples in a rod mill and screening at minus 100 mesh (.0059 in.). Fig. 1 graphically represents the data. These data indicate that carbonate rock should be relatively easy to separate from gypsum, but that shale should be difficult to separate from gypsum by differential crushing. Controlled Samples: Eight rod mill tests of hand-picked samples of mixed gypsum and shale and mixed gypsum and carbonate rock were made. Sample weight and crushing weight were standardized, but the scalping screen size was varied from 3 to 10 mesh (.265 to .0787 in.) in order to obtain the optimum purity and recovery. The data obtained from the tests (see Table I) illustrate that the relatively hard carbonate rock allows appreciable beneficiation (13.6 to 18%), but the low strength gypsum and shale allows only minimal separation (3.1 to 7.5%).* Semi control led Samples: During the investigation considerable slaking of the shale was noted when the ore was subjected to alternate wetting and drying. As demonstrated in laboratory tests, as much as 76% shale can be removed by two cycles of wetting and drying in a 48-hour period with subsequent screening at .265 in. Five ore samples, stockpiled and weathered, were screened, rod-mill crushed and rescreened at .157 or .187 in. with excellent results (Table 11).

Jan 1, 1967

By C. Burton Clark, J. Spotts McDowell

Refractories are defined as "materials having the ability to retain their physical shapes and chemical identities when subjected to high temperatures," or as "nonmetallic materials suitable for the construction or lining of furnaces operated at high temperatures." While resistance to "high" temperatures is thus the primary requirement for refractory materials, it is by no means the sole requirement. They must be able to withstand thermal shock resulting from rapid heating or cooling; other stresses induced by temperature change; pressures from the weights of furnace parts or contents; mechanical wear (abrasion) resulting from movement of furnace contents; and chemical attack by heated solids, liquids, or gases. Refractories of many kinds are needed for the many and widely diversified industrial applications. Those in greatest demand are classified on the basis of composition or properties into a few main groups, known as alumina-silica, silica, basic and insulating refractories. In each of these groups there are several classes. In addition to those included in the main groups, there are various special refractories, including silicon carbide, carbon, zircon, zirconia, alumina, and several others. Alumina-silica refractories comprise two main divisions: fire clay and high-alumina. The alumina content of fire-clay refractories covers the range from about 45 pct to 18 pct, and the silica content from 50 pct to 80 pct. The alumina content of fired high-alumina refractories ranges from about 99 pct to 45 pct, and the silica content from about 0.5 pct to 50 pct. Silica refractories of the different classes contain 94 pct to 97 pct silica. Basic refractories include periclase (magnesite), chrome spinel, forsterite, and dolomite. Refractory materials, including insulating firebrick, are supplied mainly as preformed shapes. Other products include bonding mortars and high temperature cements, ramming mixtures, plastic firebrick, hydraulic setting castables, dead-burned grain magnesite, and dead-burned dolomite. Refractory brick are classified on the basis of their physical form as Standard Sizes and Special Shapes. The Standard Sizes are brick of certain definite sizes and relatively simple design which are used in sufficient amounts to permit quantity production. The brick most widely used are the standard 9 in. X 4 ½ in. X 2 ½in. and 9 in. X 4½in. X 3 in. straights and corresponding series of sizes. All brick of nonstandard dimensions are regarded as "special shapes." They include a wide variety of brick regularly used for specific services, such as baffle tile for boilers, checker brick for regenerators, and others; together with shapes of special design manufactured on particular orders from designs submitted by the user. Not included in the broad classifications of Standard Sizes and Special Shapes are several specific-service refractory products, usually made by companies which specialize in their manufacture, or in some cases by the consumers themselves. These products include

Jan 1, 1960

By Charles S. Barrett, Robert F. Mehl, Shueling Woo

WHEN one solid phase is generated from another, fixed and rational orientation relationships are observed to subsist between the parent and the new crystal. The principle has been proposed&apos; that the relationships obtaining between the same two phases are identical whatever the type of phase change involved, or whichever of the phases may act as parent. Many types of phase changes have been studied: allotropic transformations in pure metals, precipitation from solid solutions, eutectoid decompositions, peritectic reactions, the formation of oxide layers, and others.2 Phase layers generated by diffusion of one metal into another constitute an additional type of reaction. This report provides new data on the orientation relationships occurring between , phase layers formed by diffusion, in the Cu-Zn system, § and furnishes further evidence in support of the principle. MATERIALS AND METHODS The Cu-Zn system is especially suitable for these studies since the high vapor pressure of Zn provides an opportunity readily to create one phase poorer in Zn upon a parent phase richer in Zn by removing Zn by vaporization, or to reverse this process by adding Zn from Zn vapor; e.g., the beta phase can be found as a layer upon gamma by dezincing, or gamma can be found on beta by addition of Zn from Zn vapor. Since orientation relationships are to be sought, requiring crystals large enough for orientation determinations, it is convenient to prepare single crystals or large grains of the parent phase. The samples were prepared from oxygen-free high-conductivity copper and Horse Head zinc by melting under a borax flux in a graphite crucible. Large crystals of beta brass were grown by the strain-anneal method, in plates sectioned from the cast ingots, by the following procedure. Rockwell-hardness indents were made at I cm. intervals-and with various loads, then the plates were annealed for .4 days at 700°C. in Nichrome boxes packed with beta-brass chips and graphite. Surface layers were removed by grinding and etching to a depth of about 1.0 mm., and individual grains were cut out. Crystals of alpha and gamma brass were prepared by freezing, by lowering a graphite crucible at speeds less than one inch per hour through a furnace held at a constant temperature above the melting point. Single crystals were cut out with a jeweler&apos;s saw, ground, polished and etched. Care was taken to remove cold worked layers from the finished crystals

Jan 1, 1944

By AIME AIME

THE 139th meeting of the Institute will be held Feb. 17-20, in the Engineering Societies Building, New York. The annual business meeting will be held on Feb. 18 at 10 a. m., and no technical sessions will be scheduled at that time, so that all members may participate in the election of officers, hear the presentation of the annual reports of officers and committees and discuss any matter which they may care to bring up at that time. The annual dinner will be held at the Conlmodore Hotel on the evening of Feb. 20, and the usual good time is promised. Arrangements for this and other social features of the meeting are, as usual, in hands of the New York Sec- tion, of which the chairman this year, Ralph M. Roosevelt, has a well-established reputation earned as president of the Zinc Institute, as host.

Jan 1, 1930

By K. P. Gupta

The Cb-rich boundary of the (Cb,Al) a phase field at 1250OC is near 41 pct Al. The Al atoms tend to occupy the C. N. 12 sites in this structure. A homologous (Ta,Al)a phase was identified. No a phase was found in the Mo-Al system at 1200°C. The first binary o-phase with a non-transition element as a major component was found1,2 in the Cb-Al system. The composition of this phase was reported2 as approximately 34 at. pct Al, based on X-ray diffraction patterns taken of alloys in the as-cast condition. Further study of the composition of this o-phase, therefore, appeared desirable. Since Si was previously found3,4 to occupy preferentially the lowest C.N. sites (I and IV) in the a phase, and preliminary resultsa indicated that Al may show similar ordering, one of the aims of the present work was to obtain more complete information on ordering in (Cb, Al) o. Among the binary systems of Al with Ti-, V-, and Cr-group elements, the Ti-Al, Zr-Al, V-Al, and Cr-Al systems are known to comprise no o-phase. In the present work a Ta-Al and a Mo-Al alloy were studied in an effort to find additional o phases with Al as a major component. EXPERIMENTAL PROCEDURES AND RESULTS An alloy with the intended composition of Ta + 40 at. pct Al was prepared by arc melting in He atmosphere. In both the as-cast condition and after annealing for 10 days at 1250°C and quenching in cold water this alloy consisted of two phases, as seen in the X-ray pattern and the microstructure. One of these phases was identified as the o-phase; the observed and calculated d-spacings are shown in Table I. The lattice parameters of this o-phase are a = 9.972 A, c = 5.214 A and c/a =0.5228, as determined from a Debye-Scherrer pattern using Fe K a radiation. The d-spacings for the unknown second phase are given in Table 11. The alloy contained approximately 25 pct of the unknown phase after annealing, as estimated on the basis of microscopic examination. A Mo-Al alloy was prepared by arc melting, with an intended Al-content of 35 at. pct. The alloy button was annealed for 7 days at 1200°C and water quenched. The X-ray pattern of the alloy in both the as-cast and the annealed state showed the reflections of Mo3Al (Cr30 type structure) and an unknown phase different from a. Six Cb-Al alloys were prepared in the composition range 30 to 50 pct Al. All alloys were arc melted in He atmosphere. After annealing for three days at 1175oC in evacuated silica capsules and quenching in water, the alloys with 30 to 40 pct Al contained three phases, namely the o-phase, Cb3Al (Cr3O-type structure) and an unknown phase. The alloys with more than 40 pct Al contained two phases, namely, what appeared metallographically, the o-phase and the same unknown phase. In the alloys containing less that 38 pct Al, the unknown phase was not present after annealing for 4 days at 1250°c,

Jan 1, 1962