Search Documents

By R. H. Jacoby, V. J. Berry

When dry gas is injected into a reservoir containing a volatile crude oil, a significant amount of the reservoir liquid phase may become vaporized. The resultant rich gas phase, when subsequently produced, con-tributes to tank oil production. This contribution assumes greater importance, the more volatile the oil in-olved. Oil recovery may be sub-stantially greater than that predicted by conventional frontal-drive methods, which do not consider the vaporization equilibrium between the reservoir oil phase and the injected gas. A calculation method has been (developed to account for vaporiza-. tion of the reservoir liquid phase during gas-injectiorz operations, and for the tank oil production which results from this factor. Recovery performance calculations are presented for a reservoir containing a highly volatile oil. Tank oil recovery is calculated to be about twice that predicted by the use of the conven-rional frontal-drive equations. In contrastto usual pressure maintenance performance results, in which the gas-oil ratio rises at an increasing rate after gas breakthrough, the pre-dicated gas-oil ratio rises rapidly to about 12,000 scf/bhl and then rises much less rapidly. During gas inje-tion, most of the reservoir liquid phase contacted is evaporated by the dry injection gar. The gas-oil ratio during this period is dependent upon reservoir pressure. The higher the operating pressure, the lower the gas-oil ratio. The predicted behavior i., in accordance with laboratory PVT tests made to .simulate the vaporization behavior. In addition to recovery performance predictions, results of the calculation procedure include complete wellstrearn composition data of value in the design of gasoline plant facilities often used in con-rrction with gas-injection operations. INTRODUCTION In the cycling of gas-condensate reservoirs, dry gas is injected to maintain reservoir pressure during wet gas production and to thereby eliminate or reduce ultimate loss of liquids due to retrograde condensation within the reservoir. Gas injected into crude oil reservoirs has a dual function. It displaces oil to the producing wells and at the same time serves to partially or fully maintain reservoir pressure. Oil shrinkage which would occur upon pressure reduction is thereby minimized or eliminated. Accepted calculation methods are available'= for predicting recovery performance of either gas-condensate reservoirs or crude oil reservoirs which are being subjected to gas injection. In gas-condensate reservoirs, any retrograde liquid formed does not flow, and it is necessary to account only for the vaporization equilibrium between this liquid and the injected gas. Conversely, in normal crude oil reservoirs, both the oil and gas phases flow, but it has not been considered necessary to account for any vaporization of the reservoir liquid which might occur upon contact with the dry injection gas. Recently, high shrinkage reservoir fluids known as "volatile oils" have been found in increasing amounts. These oils are characterized by tank oil gravities above 4.5" API, solution gas-oil ratios above 1,000 scf/bbl, and reservoir volume factors above two. Special techniques have been devised for predicting depletion performance of reservoirs containing such oils.74.5.1; One of the characteristics of reservoirs producing volatile oils is that the reservoir gas phase carries a significant amount of oil which is recoverable as stock-tank liquid. This unusual vaporization be-havior implies that an appreciable amount of reservoir liquid would be vaporized upon contact of the oil with dry injection gas. In a gas-injection operation, tank oil recovery would he obtained not only through frontal displacement of the reservoir liquid by the injected gas, but also through production of the rich gas phase. This means that not only are improved methods needed to predict recovery of such oils from reservoirs undergoing gas injection, but it would also be expected that high oil recoveries might be obtained by such operations. When relatively dry gas is injected in to a volatile oil reservoir, phase equilibrium between the injected gas and the reservoir oil will tend to bc established. Initially the most volatile components, such as propane, the butanes and the pentanes, will account for most of the material transferred from the oil phase to the gas phase. As the partially stripped oil phase is contacted with additional dry injection gas, the heavier intermediate components, such as the hexanes, the heptanes and the octanes, will gradually transfer to the gas phase in increasing amounts. This is because the supply of lighter components in the oil phase dwindles due to the stripping action of the injected gas. This stripping action will usually continue to be effective down

By H. O. Hofman

The object of refining copper in the reverberatory furnace is to obtain a metal which will have the highest attainable degree of malleability, ductility and electric conductivity, and present at the same time a level surface when it solidifies in the mold after casting. These desirable physical properties are governed by the character of the impurities and the forms in which they are present, by the amount of cuprous oxide retained by the copper, by the quantity of gas held in solid solution, by the casting-temperature, and by the thickness of the casting. The effects of impurities, of cuprous oxide and of gases upon the mechanical properties of copper have been studied by Hampe1 in his classical paper " Colitributions to the Metallurgy of Copper." The most recent research into the effect of metals upon the electrical conductivity of copper is that of Addicks. 2 The influence of cuprous oxide upon the electrical conductivity has been investigated by Walker3 and Addick. 4 The absorption of gases has received attention by Hampe: Stah16 and Heyn 7 The effects of casting-temperature have been noted by Stahl.8

Jan 1, 1908

[FUQUA, H. B. and Thompson, B. E.: Oil and Gas Development and Production in North Texas for 1933, 107, 320; for 1934, 114, 417 Oil and Gas Development in West Texas 114, 438 FURMAN, W. F.: Heat and Corrosion-resisting Alloys. Printed in Oil & Gas Jnl., June 13, 1935 Furnace-bottom sand, uniformity, 73, 390 Furnace control, Isley apparatus, M27, 502 Furnaces (See also Holt-Dern; Blast Furnaces; Roasters; Wirebar, etc.): annealing: electric, 89, 424 gas-fired, 89, 425 gas vs. wood for nonferrous metals, 89, 422]

Jan 1, 1936

By Carl Pierce

The writer of this article has not attempted to write a technical paper; on the contrary, he has tried to express in "steel-plant English," for steel men, a viewpoint drawn from his practice and experience. It is not his thought that it shall be taken as the "last word" in the making of this class of steel, or that good rimming steel cannot be made by any other practice. The paper was written to serve as the basis of a discussion from which it is hoped much benefit may be derived. The paper deals only with rimming steel made by the open-hearth process, and with the lower carbon steels, such as sheet and tin bar, rivet stock, skelp, etc., although good rimming steel as high as 40 to 50 carbon can be made by having good open slags and giving proper attention to working and tapping temperatures. Definition of Rimmed Steel Rimmed steel is sometimes called open or effervescing steel to differentiate it from killed or partly killed steel. It is steel made by a process which permits the free escape of gases from the metal in the molds. In passing up through the metal, the gases keep it in a rolling action from the walls of the mold inward. The top of the ingot rims in as the metal chills and the walls of the ingot get thicker, the center part remaining fluid until it reaches a pasty condition when it is covered with a cast-iron cap. The Charge In making up a charge for rimming steel, clean stock of a known composition must be selected, special attention being given to the analysis of the materials. The silicon in good rimming steel must be eliminated to a trace, therefore it is advisable to have a uniform amount going into the charge. Too much silicon gives a raw melting heat from which rimming steel is unlikely to result. For this reason a charge containing not to exceed 40 per cent. pig iron and 60 per cent. scrap, with no iron ore, is preferred to the Monell type of charge in which as high as 65 to 70 per cent. pig iron is used with a proportional amount of iron ore for the removal of the excess silicon and carbon. The silicon content of pig iron varies so much from day to day in the average blast-furnace practice that there is danger of getting too much of this element in the latter mixture when

Jan 1, 1926

By H. K. Martin

IN September 1954 the Lavender pit concentrator at Lowell, Ariz., began treating low grade porphyry copper ore from the nearby Lavender mine. Nominal capacity of the mill is 12,000 tpd, but production now averages 16,226 tpd. Plant design was somewhat affected by the re-use of old equipment and the substantial re-use of old buildings. A breaking-in period between June 24 and Sept. 1, 1954, was devoted to training operators and making minor changes in launders, chutes, and piping. From Sept. 1, 1954, to July 1, 1956, the mill treated 8,598,105 dry tons of ore, from which 556,541 tons of concentrate were produced, containing an indicated 144,055,185 lb of copper.

Jan 11, 1957

By John Jermain Porter

PAGE. I. INtroduction............ 191 I1. Derivation of Formula foR Fuel-RequiRements.... 192 1. Heat Available in the Hearth........193 a. Method of Calculation..193 b. Data for the Determination of Critical Temperature.. 195 2. Heat Necessary in the Hearth ...... 197 a. To Care for Slag..197 b. To Care for Pig-Iron...198 c. To Reduce Silicon........198 d. For Other Items.........199 3. The Effects of Rate of Driving ..... 199 4. Loss of Carbon Between Throat and Hearth.....201 a. Solubility of Coke..201 b. Carbon-Loss Due to Flux....201 c. Effects of Reducibility of Ore..202 5. The Formula as Used........203 III. The LImitations of the Formula........ 204 1. Through Effects of Irregular Furnace-Work.....204 2. Through Ratio Between Heat-Requirements in Shaft and Hearth. 20.5 IV. The Formula Applied to Actual Furnace-Records,.. 209 1. Description of Furnace-Stock........ 209 2. Furnace Dam..........210 3. Application of Formula..211 4. Average Furnace-Practice..213 V. Sources of Error........... 214 VI. SuggesTions for Practical Methods of Fuel-Economy... 215 VII. Efficiency as a Factor in Furnace-Management.... 219 1. The Efficiency Principle........ 219 2. The Application to the Blast-Furnace..220 I. Introduction. The heat-balance of the blast-furnace has been a favorite subject for discussion for many years. and its study has contributed much to our knowledge. and still possesses a certain academic interest. As a means of accounting for differences in fuel-consumption, however. it has failed utterly. and it is evident that we must look elsewhere for the means of accomplishing this end.

Jan 1, 1912

By Thomas S. Blair

I FEEL a certain sense of responsibility in bringing before you the subject of the direct process in iron manufacture. I am aware that, in such a body as I have now the honor of addressing, there are few who are not already so well informed upon its past history that it would be a weariness to them to listen to anything else than an account of practical success. Yet, to claim that success involves so much that, if I do not make good my claim, I deservedly expose myself to severe criticism. The whole literature of the art, so far as it relates to the direct process, is, up to this time, but a history of failure. It is safe to say that more money, time, and talent have been fruitlessly spent in the pursuit of this object than in all the other unsuccessful efforts in the whole line of iron metallurgy. A distinguished authority in patent law has remarked that " the invention records of the United States and of foreign countries are filled with the waifs and abandoned relics of these abortive struggles." Dr. Percy, whose great work may be taken as an epitome of all that was worth mention, whether useful or curious, in pig-iron metallurgy, up to the date of its publication (1864), after giving elaborate accounts of various attempts at the direct process, condenses his own opinion of all that had been then effected, into a brief but summary comment upon a pamphlet of one of the sanguine inventors who had said: "It is evident that the present mode of working iron

Jan 1, 1874

By Frederic Becket

IN a recent article,1 which described the softening effect of columbium in plain high-chromium steels, the authors stated that their investi-gations had shown columbium to be also a particularly valuable inhibitor of intergranular corrosion in steels of the 18 per cent chromium, 8 per cent nickel type. It is the purpose of the present paper to record some of the results obtained through the introduction of columbium to the austenitic chromium-nickel steels. The damaging effects of this type of corrosion have become so widely known as to restrict considerably the applications of the steels under consideration, and therefore there is little question of the importance of the goal to be attained. Numerous contributions concerning the susceptibility of the aus-tenitic chromium-nickel steels to intergranular corrosion have appeared during the past few years, and among others who have dealt construc-tively with the subject are such well-known authors as Strauss and Houdremont of Germany, Hatfield of England, and Bain in the United States. Different theories have been propounded as to the cause of intergranular corrosion, and various remedial measures have been proposed, the majority of which involve the use of addition agents. Titanium is the addition agent at present most generally employed, as suggested by Houdremont and modified as described by Bain, Aborn and Rutherford.2 Little has been published on the effects of holding these steels for long periods at the relatively lower temperatures in the presence of

Jan 1, 1934

By S. A. TAYLOR

THERE is probably no other mineral industry of which the public has as much information and misinformation as it has of the coal industry. Unfortunately, however, the general public's knowledge of the coal industry, outside of the particular kind of coal it is accustomed to, by reason of use, is largely made up of information received from newspaper and popular magazine articles, in which the mine workers are depicted as overworked and mistreated men, and the coal operators as "coal barons." Those who have any specific knowledge of exact conditions in the coal industry know how unjust and un- fair such an opinion of the coal industry is, not only to the miner but to the operator as well. Many reporters and writers of magazine articles are misled by statements regarding the condition of the miners that are exaggerated and not founded on facts and, if an investigation of the conditions of the miner's work, his habitation and surroundings were fairly made, it would at least compel more truthful statements by those who write for public reading. That such an investigation would not reveal anything that was wrong, or anything to be censured or cured, no one, I think, would maintain, but I do think that any fair investigation of the facts would show that conditions in and around the newer and later-developed coal mines and communities would compare favorably with those of manufacturing districts, and that where the mines and com- munities are old and not very attractive places to work, or live in, they carry with them other considerations, compensating for these conditions, and cannot be remedied by reason of a lack of sufficient coal to warrant economically any costly changes.

Jan 1, 1926

By Blake M. Loring

RECENTLY the S-curves for 30 to 40 alloy steels have been published.1,2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.20 percent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr. at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1 1/4 by 1/2 by 1/8 in. Wires attached to the samples were used for handling, instead of tongs, to avoid chilling. The specimens were heated at 845°C. for 1/2 hr. and quenched into constant-temperature salt baths held at various temperatures from 205° to 650°C. The time required to transfer the specimens was found to be about x 1 1/2 sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 21°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1941

By Robert S. Archer, Zay Jeffries

It is about fifteen years since the development in Germany, largely by Alfred Wilm, of the aluminum alloy called duralumin. In this alloy, combining as it does the tensile strength of mild steel with the lightness and corrosion resistance of aluminum, a distinctly new material was presented to the engineering world. Despite the evident usefulness of this material, however, its commercial development has been slow, due in part to the difficulties involved in its fabrication. In view of the potentially great utility of strong aluminum alloys, it seemed desirable to find means of producing such alloys with better fabricating properties, and work was undertaken with this object in the laboratories of the Aluminum Company of America several years ago. This work has resulted in the production of two new types of aluminum alloy of the "strong alloy" class, having distinctly improved fabricating qualities. The knowledge gained has also made it possible to produce alloys of the duralumin type with greater strength and hardness than previously obtained. There have thus been made available some new engineering materials which it is the object of this paper to describe. These alloys, induding duralumin, are fundamentally wrought alloys. Castings of the same compositions heat treated in the same manner give inferior physical properties, particularly as to ductility. The statements made subsequently concerning properties and heat treatment apply to material that has received sufficient working to thoroughly break down the cast structure. The material referred to has, in general, undergone a reduction in section of at least 80 per cent, by mechanical working. It may be mentioned in passing that other compositions have been found that are suitable for the production of the maximum physical properties in heat-treated castings.

Jan 1, 1925

By Walter Harvey Weed

(Mexican Meeting, November, 1901.) Among the many causes of that perplexing featurc of mineexploitation, the unequal distribution of the ore, the influence of the country-rock upon the vein-contents has long beer1 accepted as an important factor in certain districts, but the general application of the theory has not been proved. It is now possible to obtain trustworthy data with which to test the theory, and either to confirm or to overthrow this time-honored

Jan 1, 1902

By John M. Kelly

This report covers the development, exploratory drilling, and production of oil and gas in New Mexico during 1945. The statistical information was gathered from state regulatory agencies and other sources believed to be reliable; it is presented here in combined form for general information only, and the author assumes no responsibility for its accuracy or completeness.

Jan 1, 1946

By C. Upthegrove

DURING the past year considerable work dealing with physical properties of cartridge brass was done at the University of Michigan in cooperation with the Ordnance Department of the U. S. Army. This paper gives some of the data bearing on the effect of the anneal, previous to the final reduction or rolling, on the physical properties, particularly the hardness. Various phases of the subject of physical properties of cartridge brass have been presented by different investigators. Mathewson and Phillips1 refer to the work of Grard, in 1909, as the first systematic presentation of the relation between temperature-and time of anneal; changing of physical properties and microstructure, and the previous reduction by cold rolling. They discuss the relation between time and temperature of anneal and the previous reduction by cold rolling also; the relation between physical properties and grain size of annealed brass. The degree of deformation previous to the annealing was found to determine the temperature at which recrystallization and corresponding changes in physical properties would take place. Bassett and Davis,2 in establishing the relation between grain size and Brinell hardness; found the hardness for low-temperature annealing to be dependent on the previous degree of reduction, while for anneals above a certain temperature the hardness after the anneal was independent of the degree of reduction. Actual differences in hardness, due to the degree of reduction, disappear only on annealing at 600° C. or above; though the differences for metal subjected to different degrees of reduction and annealed at temperatures between 350° and 600° C. were found to be relatively small. In their determination of the relationship of grain size to Brinell hardness, Bassett

Jan 5, 1922

By Steven T. Mitchell

INTRODUCTION Mill production from the Homestake Mine in 1979 amounted to 1.29 Mt (1.43 million st) of ore containing 5.9 g/t of gold (0.172 oz per st) compared with 1978 production of 1.44 Mt (1.59 million st) containing 6.2 g/t of gold (0.180 oz per st). The average cost per ounce of gold produced in 1979 rose to approximately $250 contrasted with $176 in 1978. This increase in unit cost is the result of inflation, a diminishing ore grade, and productivity losses related to a shortage of experienced miners as well as compliance with federal regulatory requirements. Together, these factors prompted the investigation of several large-scale, highly mechanized underground mining methods. This analysis indicated Vertical Crater Retreat mining to be one of the safest underground methods known today, yet competitive with all other forms of stoping in terms of cost and productivity. Therefore, the feasibility of applying the VCR stoping method at the Homestake Mine was explored. Vertical Crater Retreat stoping is a recent innovation in large- scale underground mining based on C. W. Livingston's crater blasting theories. Figure 1 illustrates the method which consists of drilling 165.1-mm-diameter (6.5-in.) holes from a topsill down-dip to an under- cut on the level below. The bottom of each hole is then loaded from above with a predetermined charge weight and horizontal slices up to 4.27 m (14 ft) in thickness are blasted into the undercut. Broken ore is extracted from drawpoints located on or below the undercut level.

Jan 1, 1983

By C. C. McDermond

In reviewing petroleum development in Venezuela during the year 1936, it is well to bear in mind certain factors that affected progress, although not directly connected with the oil industry itself. At the start of the year, when the present Federal Administration took over the reins of government, reaction against the former regime resulted in some popular uprisings. Although these were entirely political in character, they were not without their effect on the oil industry itself. Such popular agitation really ended with a short general strike in Caracas, Maracaibo and other cities during June, these strikes being based on demands for certain changes in government policies. The strikes were duly investigated and their motives taken into consideration by the executive power or by Congress, and during the year many of the civil, political and administrative laws have been revised. In June and December, however, it was necessary to suspend activities in drilling and production work, particularly in the Lake Maracaibo Basin area. In June a strike caused a five-day shutdown in the main producing fields and on Dec. 14 labor difficulties resulted in a shutdown that continued to the end of the year, which necessitated suspension of all drilling and production in the Lake Basin area and curtailment of shipments to deep-water terminals. Actually, the strike lasted for a period of 42 days, until Federal intervention brought the dispute to a close with minor wage increases to workers hut with no loss of initiative or independence on the part of the oil companies. Operations in eastern Venezuela were not affected by the labor disturbances, production and exports having been reduced in December only in the Lake Basin fields. Well Completions On Jan. 1, 1937, a total of 3384 wells had been completed throughout Venezuelan fields, as compared with 3094 on Jan. 1,1936. Of these wells, 2005 were producers. The 290 completions effected during 1936 were by the following operating companies: Lago Petroleum Corporation, 123 completions; Dutch Shell group, 104; Standard Oil Company of Venezuela, 46; Mene Grande Oil Co., 15; British Controlled Oilfields, Ltd., 2.

Jan 1, 1937

By Paul A. Beck

It is well known that the hardness of metallic single crystals, like that of polycrystalline metals, increases during deformation (hardening by cold-work). It is also known that, as a consequence of deformation. the metallic material acquires an evident thermodynamic instability, revealed, for example, by the fact that the increased hardness gradually decreases with time, especially at elevated temperatures (softening by annealing). The temperature at which the stabilizing process begins is different for various metals, and for any metal it depends on the amount of deformation. Such stabilization of deformed metals may proceed in two different ways: through recovery, and through recrystallization. The former process allows the unstable deformed metal body to approach stability gradually and without visible change in the grain structure; the latter process, like an allotropic transformation, yields directly the undeformed stable "phase" in the form of new undeformed crystals, which, starting out of a certain number of nuclei, grow into and " consume " the deformed hard material. The extent of stability attainable through recovery is limited, especially if the deformation of the metal crystal or crystals involves not only the gliding along slip planes, but also the bending of the slip lamellae, or at any rate the bending of comparatively large parts of the crystal lattice. In such cases, for instance in bent single crystals or polycrystalline metals subjected to any deformation, recovery will not as a rule be able to restore the "istraight" undeformed lattice, and stability can be attained only by recrystallization; that is, by the consumption of the bent crystal lattice parts by new, undeformed crystals—a much more drastic process. It is evident that the part of the surplus free energy stored in deformed crystals, which is present in the form of the elastic energy of the bent lamellae, is in these instances not considerably involved

Jan 1, 1937

By E. C. Nelson

An equation is derived for calculating approximately the solubility of nitrogen in an alloy steel over a temperature range from 1200" to 1900°C using data on the effects of alloys on the activity coefficient of nitrogen in iron at 1600°C. Calculated values are compared with experimental data. STUDIES involving the solubility of nitrogen in complex iron alloys have been aided by a system devised by Lanenberg for calculating the solubility of nitrogen in ternary and higher alloys of iron at 1600C using available data on the activity coefficient of nitrogen in binary alloys. Calculated nitrogen solubilities agree well with experimental determinations on complex alloys,' and the calculation procedure is useful when experimental data on specific alloys are not required. A method for extending calculations of nitrogen solubilities in alloy steels to temperatures other than 1600°C would be useful because of the paucity of experimental data in this area. Assumptions which must be made to permit this calculation introduce an element of approximation; however, the calculation is useful in cases where a large number of alloys and temperatures are under consideration, and the precision of experimental measurements is not required. The activity coefficient can be freed from the isothermal restriction of Langenberg's calculation if it is assumed that the solution is "regular". This is a reasonably good assumption for solutions of nitrogen in iron alloys, because usually they are dilute and the heat of solution is relatively small. The presence of large amounts of certain alloying elements would make this assumption less tenable.3 One of the properties of a regular solution is: when "f" is the activity coefficient of a solute and "T" is the temperature in OK. If the activity coefficients at temperatures T and T2 are denoted by subscripts 1 and 2 respectively: The activity coefficient of nitrogen in a complex alloy then can be calculated at any temperature from the sum of the effects of the other solutes on the activity coefficient of nitrogen at 1600°C. It will be convenient to incorporate this expression into an equation which will give directly the logarithm of the solubility of nitrogen at any temperature in the presence of alloys. Two constants, the solubility of nitrogen in pure iron at 1600 "C and the partial molar heat of solution of nitrogen in iron are required. The heat of solution value of 1400 cal at 1600 °C quoted by Kubaschewski and vans will be used. The accuracy of the calculation will suffer if the heat of solution should change materially with temperature. In the absence of experimental data on the temperature dependence of this quantity, it will be expedient to restrict the application of the calcula-

Jan 1, 1963

By John C. Draper

The principal object of an underground coal mine transportation system is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside; it must move men in and out of the mine; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served : 1) Face Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling

Jan 1, 1981

By P. D. P. Hamilton

In any mining district where benefication of the ores is practiced, one can usually observe several types of flow sheets even though the various producers are milling ore from the same geological formations. It is obviously impossible to describe all the mills in the Porcupine district. However, the following description of some of them is of particular interest in that it shows where one mill has paid particular attention to corduroy blanket practice; one to gravity concentration of sulfides for intensive cyanidation of the values therein contained; one to flotation of values and cyanidation of this product only; and others where small variations of standard all-slime cyanidation practice prevail. In all cases it will be seen that cyanidation is the basic principle. Discussions involving the difference in the flow sheets and the reasons for them will always be of value to those interested in the art. The author of this article, however, believes that such discussions should originate from the operators of the mills under discussion. For this reason no comparisons or discussion will be included in the description of the mills mentioned. Should any reader of this article obtain information therefrom which will be of value to him in helping to solve his own particular problems, the author will consider that the article has satisfactorily served its purpose. All values mentioned throughout this article are based on the value of gold at $20.67 per ounce. Coniaurum Mines, Limited The ore of the Coniaurium mines consists of a mineralized schist and quartz containing about 2.5 per cent sulfides. Owing to the low grade of ore developed in the mine, extreme care has had to be exercised throughout the entire mining and milling operation in order that an operating profit might be obtained. The management, however, has been able to keep costs down, with the result that at present the outlook for the property is considerably brighter than it has been in the past. This is partly due to the fact that it is now known how to mine and treat

Jan 1, 1935