Search Documents

By T. D. Mueller, H. Dykstra

This paper describes a method for obtaining compositions of gas and oil phases in equilibrium with each other at a given reservoir temperature and pressure as lean or enriched gas is injected into a reservoir oil not in equilibrium with the gas. The method is based on calculation of equilibrium constants, K, from the equation log Kp = A + B F, where p is pressure and F is component characterization factor. A and B are constants that vary with a composition parameter. The paper explains how A and B could be determined with a minimum amount of data. The method consists of calculating equilibrium constants as a function of liquid composition and using the K's to calculate changes in compositiort of injection gas as it successively contacts original resetvoir oil at the gas-oil front and the change in composition of reservoir oil as it is successively contacted by the injection gas in the vicinity of an injection well. An iterative process is required. Two examples of the method are given which show how oil and gas compositions and properties are calculated with the aid of a computer. INTRODUCTION The calculation of recovery from lean-gas or enriched-gas injection into a saturated or under-saturated reservoir oil requires a knowledge of how phase properties change in a reservoir between injection well and producing well. To determine the phase compositions or properties experimentally would be difficult and time consuming, especially if one wanted to look at the effect of various injection gas compositions. For some fields an engineer would want to make preliminary calculations on the economics of gas injection before he makes the decision to spend a corrsiderable sum of money for laboratory work to obtain the necessary fluid properties. A method for calculatine compositions and properties based on a minimum of laboratory data is described. The minimum amount of data required is injection gas and reservoir oil composition and injection gas solubility as a function of pressure for an undersaturated oil, or the compositions of mixtures of reservoir fluid with two or more enriched gases, which mixtures have a bubble-point pressure that is the same as the expected average displacement pressure. On the other hand, if the economics appear to be attractive, more laboratory data can be obtained in the form of equilibrium constants for three or more mixtures of the reservoir fluid and injection gases. The method is based on the calculation of K's from the equation, log Kp = A + B F, where K is equilibrium constant, p is pressure and F is component characterization factor. This method of plotting K data by means of the above equation is described by Hoffman, Crump and Hocott.1 A and B are constants that vary with a composition parameter. It is shown how experimental data are used to determine how A and B vary with composition. BASIS OF METHOD EQUILIBRIUM CONSTANTS Equilibrium constant (K) data are required for this method. The K of each component is obtained from an equation that gives the product of K and pressure as a function of component characterization factor. The characterization factor F = b(l/Tb — l/T), where b is a constant characteristic of a given component, Tb is the boiling point in OR at atmospheric pressure of the given component, and T is the temperature of the system in OR. This method of plotting K data is described by Hoffman, Crump and Hocott.l The straight-line equation of the log Kp - F plot is log hp = log Kop +BFi, where Kop is at F =0, i designates the component, and B is the slope of the line. The factor F can be

Jan 1, 1966

By R. W. Raymond

FOUR portraits have recently been hung in the rooms of the Institute, in recognition of four illustrious men with whom we, as mining engineers and metallurgists, may claim fellowship. LUTHER. Martin Luther is often spoken of as a miner's son; but it is less generally known that John Luther, his father, was, in a small way, a metallurgist as well as a miner, and that Martin Luther himself, in his youth, worked in a forge or bloomary established by his father at Mansfeld, Saxony. Since this is the only manual occupation on his part of which we have any record, it is fair to assume that the great scholar and reformer derived from his work in this department the practical familiarity with the conditions of human labor so abundantly evinced in the homely illustrations which accompany even his serious arguments, and in the witty apothegms of his famous "table-talk." At the same time, I must confess that 1 have not been able to find in any of the works of Luther distinct allusions to mining or metallurgy. KÖRNER. Theodor Körner, a student at the Mining Academy of Freiberg, Saxony, threw himself into the German War of Freedom in the first decade of the 19th Century. He was a poet of no mean rank ; and his " Song of the Sword " is one of the great lyrics of literature. This poem was written but a few days before he died in battle. In many respects, Körner may be compared with our American hero Theodore Winthrop, who similarly met a glorious fate, and left behind him prophetic indications of genius, of which his premature death prevented the complete fulfillment. I am informed by a member of the Institute that Körner's admirable collection of minerals is still preserved at Dresden.

Nov 1, 1908

By C. W. Lawr

The ores mined by the Santa Gertrudis Co. at Pachuca, Mexico, arc mainly silver-bearing; they also yield some gold and carry a little copper. Strong cyanide solutions are used to dissolve the silver and gold, and the mechanical loss of cyanide at the tailings filter has been considerable. Prior to the year 1923, the pulp, after agitation, was given a 35 to 37-min. wash with barren solution in a Butters-type leaf filter; the discharged slime cake was repulped and pumped into eight Merrill self-sluicing slime presses in which the slime was given a further wash with barren solution for 25 to 35 min., followed by a 10-min. water wash. At that time the barren solution titrated around 0.350 per cent. free KCN and 0.500 per cent. total KCN. (Aero brand cyanide is used.) It can readily be seen that a 10-min. water wash would leave considerable cyanide in the filter cake, which of course was a total loss. This averaged 0.522 kg. (1.15 Ib.) KCN per ton of solution. As the daily discharge to the dam was 1600 tons' of slime of a 2:1 ratio of liquid to solid, the value of this mechanical loss of cyanide was an important item and it's recovery held alluring possibilities. Principle of Cyanide-recovery Process As it had acquired the patent rights to theLayng (H. R.) and Halvor-sen (A. L.) processes, also those of Mills (L. D.) and Crowe (T. B.) after considerable experimental work in its own laboratory and at Tonopah, Nev., The Merrill Company of San Francisco early in 1923 notified the Mexican Corporation and compania de Santa Gertrudis of its process for the recovery of cyanide from weak wash solutions, or for the transference of cyanide from a foul mill solution to a clean alkaline solution. This method is known as the Mills-Crowe process, the principle of which is as follows: The solution from which the cyanidc is to be removed is made acid by bringing it into contact with sulfur dioxide (SO2). The acidified solution is the; transferred to a closed tank in which air and solution are brought into intimate contact. The air leaving the tank charged with HCN is then passed to another tank in which it is mixed with an alkaline solution,

Jan 1, 1930

By O. W. Ellis

The question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,' Iwase,2 Lobley and Jepson3 stand preeminent. Solubility of Gases in Copper Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate—possibly 30" to 60" C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1929

By O. W. Ellis

The question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,' Iwase,2 Lobley and Jepson3 stand preeminent. Solubility of Gases in Copper Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate—possibly 30" to 60" C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1929

By L. T. Leyson, U. C. Tainton

Some time ago, at ameeting of the Institute Prof. J. W. Richards1 said, "I take exception to the statement that all the factors in the production of electrolytic zinc were known long ago.... There is possible in my opinion an improvement of perhaps 50 per cent. in the new electrolytic processes." An examination of the literature of the subject will show the justness of Professor Richards' contention. The work of the earlier investigators was carried on in the shadow of difficulties that, today, are hardly more than memories. We seldom hear now of zinc sponge, that bête noir of the electrolytic-zinc pioneers. Zinc sponge was the name given to a peculiar, soft, black, non-adherent form of zinc deposit that was utterly useless for melting into ingot form. At the big plant at Cockle Creek, New South Wales, in 1897, Edgar Ashcroft2 said that the solution in the plant would suddenly, and without ascertainable cause, go' "bad" and begin to deposit spongy zinc. The most delicate, even spectroscopic, methods of analysis were unable to detect any difference between "good" solution and "bad" solution; either form might change to the other on being kept for a while. When it is added that an outbreak of this insidious disease (which appeared to be infectious, or at least contagious) could be dealt with only by discarding the solution and washing out all tanks and pipe lines, some idea may be gathered of the troubles of the zinc electrometallurgist in what may be spoken of as the "sponge age" of electrolytic zinc. Thanks to the efforts of a number of investigators, we are today able to diagnose with considerable certitude the nature of the malady that puzzled Ashcroft and his co-workers. The researches of Mylius and

Jan 1, 1924

AMONG the features that make Inspiration of outstanding A interest, particularly to the engineer, is the fact that at various times it has used, as a major method of production, three more or less distinct methods of mining and three distinct methods of treating its ores. The following chronology is of interest : Major Mining Methods: 1915-194 7 Underground block-caving, exclusively 1948-1952 Underground block-caving and opencut mining 1953-1954 Underground block-caving, opencut mining, and "glory-hole caved-block transfer" mining 1955 on Opencut mining and "glory-hole caved-block transfer" mining. Major Ore Treatment Methods: 1915-1925 Flotation concentration exclusively 1926-1930 Flotation concentration and ferric sulphate leaching 1931-1955 Ferric sulphate leaching (the so-called "Dual Process" was used for eleven months in 1937 when demand for copper was phenomenal; and the "leach-float" process was used for 24 months in 1942-44 as an expedient to help meet war demands for copper). 1956 on "Dual Process" combining a sulphuric acid leach followed by fine grinding and flotation of the residue from the leaching vats.

Jan 1, 1957

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By R. M. Hudson

A study has been made of the decarburization of low-carbon sheet steels at temperatures from 1100" to 1475°F in mixtures containing hydrogen, nitrogen, water vapor, and in some instances carbon monoxide. Decarburization occurs principally by the reaction C (in steel) + H20 = CO + H2 and follows a first-order rate law. The decarburization rate appreciably increases with an increase in temperature up to about 1325°F, but the increase in rate is small with fur- Use of a dry hydrogen atmosphere results in a relatively slow decarburization of steel and use of a wet hydrogen atmosphere results in relatively rapid decarburization. It is now generally recognized' that the reaction C (in steel) + H2O = H2 + CO [l] accounts for most of the decarburization that occurs in wet hydrogen-containing atmospheres. The present article is concerned with the decarburization of low-carbon sheet steel in H2-N2 atmospheres ther increase in temperature. The limiting rate of decarburization can be predicted from a knowledge of the solid solubility and diffusivity of carbon and this rate is approached as the water-vapor content of an atmosphere is increased. Hydrogen contents above about 8 pct are beneficial only in that they permit higher levels of water vapor to be used without oxidation of the steel. A buildup of CO in the atmosphere lowers the rate of decarburization. containing various amounts of water vapor and carbon monoxide. The effectiveness of these atmospheres and the influence of temperature on decarburization rate will be considered. EXPERIMENTAL WORK The chemical compositions of the three steels used in decarburization-rate studies are listed in Table I. Steel A was a commercially hot-rolled rimmed steel that was cold-reduced at the Laboratory to furnish specimens 0.025, 0.041, and 0.059 in. thick. Most of the experiments in which this steel was used were made on the 0.041-in.-thick material. Steel B and Steel C were cut from 0.010-in.-thick commercially cold-reduced coils that were

Jan 1, 1963

By George A. Moore, Donald P. Smith

In spite of many investigations of the occlusion of hydrogen in iron, the nature of the process and the reasons for the accompanying effects upon the metal are still open questions. This is in large part due to three causes: (1) the difficulty of obtaining iron of adequate purity as starting material; (2) the occurrence of allotropic transformations, which complicate the effects; and (3) the fact that the body-centered cubic modification does not lend itself readily to crystallographic investigation. The present paper attempts a critical review and correlation of the somewhat scattered and disconnected existing observations, and an experimental determination of the extent to which the conclusions that appear to follow from these are applicable to iron of really high purity, studied under well-defined conditions. Review Although only a comparatively few investigations have so far been made on the pure system iron-hydrogen, there is a much larger volume of literature which throws some light on the problem but falls short of a place in the systematic investigations, either because no attempt was made to measure equilibrium conditions or because the metal used was not iron or the gas not pure hydrogen. Such results have been variously dismissed in the past as of no importance, or as too complicated to try to explain; or they have been explained in terms of any of a dozen or more pictures, each of which is contradicted by data from other sources. The present importance of these data thus arises from their very mass and diversity, which present a picture of occlusion as a phenomenon whose variability cannot be ignored. We have attempted to organize the literature into groups comprising similar experiments or data leading to similar conclusions, thus of necessity sacrificing accuracy of historical order. Lattice Occlusion.—Throughout this discussion, the term "lattice occlusion" will be used to denote the formation of a simple solid solution of a gas in a metal lattice, usually of interstitial distribution. The word

Jan 1, 1939

By George A. Moore, Donald P. Smith

In spite of many investigations of the occlusion of hydrogen in iron, the nature of the process and the reasons for the accompanying effects upon the metal are still open questions. This is in large part due to three causes: (1) the difficulty of obtaining iron of adequate purity as starting material; (2) the occurrence of allotropic transformations, which complicate the effects; and (3) the fact that the body-centered cubic modification does not lend itself readily to crystallographic investigation. The present paper attempts a critical review and correlation of the somewhat scattered and disconnected existing observations, and an experimental determination of the extent to which the conclusions that appear to follow from these are applicable to iron of really high purity, studied under well-defined conditions. Review Although only a comparatively few investigations have so far been made on the pure system iron-hydrogen, there is a much larger volume of literature which throws some light on the problem but falls short of a place in the systematic investigations, either because no attempt was made to measure equilibrium conditions or because the metal used was not iron or the gas not pure hydrogen. Such results have been variously dismissed in the past as of no importance, or as too complicated to try to explain; or they have been explained in terms of any of a dozen or more pictures, each of which is contradicted by data from other sources. The present importance of these data thus arises from their very mass and diversity, which present a picture of occlusion as a phenomenon whose variability cannot be ignored. We have attempted to organize the literature into groups comprising similar experiments or data leading to similar conclusions, thus of necessity sacrificing accuracy of historical order. Lattice Occlusion.—Throughout this discussion, the term "lattice occlusion" will be used to denote the formation of a simple solid solution of a gas in a metal lattice, usually of interstitial distribution. The word

Jan 1, 1939

By Charles R. Simcoe

The stress-strain curves in the microyield region for various Fe-C solid solutions shown by Davies and Ku are typical examples of parabolic curves defined by the expression a = kEn 111 These data, when replotted on log-log coordinates, as shown in Fig. 9, exhibit three essentially parallel straight lines. It is apparent that carbon increases the flow stresses, but does not affect the exponent n. In other words, the only factor in Eq. [1] affected by in in carbon content is the constant k. As Eq. [1] is written k is the stress at a strain of 1.0. This is unsatisfactory for examining data in the microyield region. Therefore, the equation can be altered to the form: to permit the use of the authors' microyield stress at a strain of 10-6 as k. Extrapolating the curves in Fig. 9 to a strain of 10-6 gives stress values of 2000, 3200, and 5400 psi for 0.008, 0.014, and 0.02 pct C, respectively. These values do not agree exactly with the authors' measured values, but this will not affect the following discussion. The effect of carbon content on the slopes of the stress-strain curves shown in Fig. 2 of the paper by Davies and Ku can be analyzed by differentiating Eq. [2] with respect to strain. Thus: where n is always less than 1.0. Since n is essen- tially constant as a function of carbon content for the data under discussion, the slopes of the stress-strain curves depend only on k and E. If the slopes are examined at various selected Plastic strains. i.e., 10-6, 10-5, and so forth, it follows from Eq. [3] that the dif-ferent slopes for the different carbon contents depend only on the different values of ke=10-6. Thus, the larger ke=10-6, the steeper the linear stress-strain curve will rise with increasing plastic strain. This

Jan 1, 1969

By Ralph Hultgren

FEW phase diagrams of alloys composed of two transition metals have been adequately studied, probably because of the high melting points involved. Transition metals are the elements that have inner shells incompletely filled with electrons. They comprise groups IIIa to VIIIa of the periodic table, including more than half of all metals. We have chosen to study two systems whose comparatively low melting points allowed the alloys to be melted in a molybdenum resistance furnace. The nickel-palladium system proved to consist of a simple series of solid solutions, but iron-palladium manifested several remarkable features. The main characteristics of the latter diagram were decisively established, but lack of time prevented precise determination of phase boundaries. The gamma to alpha transformation in this system is unusual and warrants further study. Grigorjew1 determined the liquidus and solidus of the iron-palladium system by thermal methods. He found a minimum melting point, but no eutectic. He also found that palladium lowered the gamma to alpha and raised the gamma to delta transformation temperatures of iron, with a complete series of solid solutions existing between gamma iron and palladium. His measurements also indicated a compound or super-lattice near the composition FePd3. Jellinghaus2 found that annealing at 500° C. greatly increased the magnetic coercive force of an alloy of composition FePd. X-ray dif-fraction photographs showed that a tetragonal ordered phase had formed during the anneal.

Jan 1, 1939

Discussion of the paper of FRANCIS S. PEABODY, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 125, May, 1917, pp. 775 to 781. THE CHAIRMAN (CARL SCHOLZ, Chicago, I11.).-Coal wastage is undoubtedly one of the most prominent topics before the coal operators of the United States today. Even those who have been in the business only 25 years, like myself, know that the exhaustion of coal is something that should and must, be curbed. If it is not, before long we shall discover that the great coal resources of the country are not what we-thought they were; we have been so accustomed to work at the best and thickest coal alone, that it will be difficult for us to realize one of these clays-and that (lay is not far distant-that we are no longer the rich nation in coal that we thought we. were. In this connection I feel obliged to attach a little blame to the Geological Survey for misleading the people. There are several members ,here who assisted in that work, and I am going to ask them to defend themselves. The Geological Survey deals with coal seams of much less thickness than we could now expect to, mine, particularly with the present high wages, excepting at a prohibitive cost. The Geological Survey, in its estimates, does not discriminate between thick and thin seams, but simply estimates our resources at so many hundred thousand billion tons of coal. I believe they include seams from 15 to 18 in thick, but you all know that a vein below 3.5 or 4 ft. is not considered economical to mine at this time. R. V. NORRIS, Wilkes-Barre, Pa.-Mr. Peabody has evidently been thinking almost entirely of Illinois conditions, with which I regret to say I am absolutely unfamiliar. In some West Virginia mines the total recovery at present is considerably over 90 per cent. and extraction-, as high as 97 or 98 per cent. are claimed.

Jan 1, 1918

By M. G. Corson

The iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well-known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 1.5 per cent. silicon (Fig. I). Starting at the ultimate strength of 35,000 lb. and at a yield point of 16,000 lb. for pure electrolytic iron, one reaches a maximurn strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb, per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2..5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent., a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated. Yensen observed an enormous drop in elongation and area reduction at about 2.65 per cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to 1.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction. Yensen's graphs, as shown in Fig. 1, indicate also a considerable drop in strength and yield point at the same point of 2.65 per cent. Si,

By W. F. Boericke, T. H. Garnett

The Wisconsin zinc district, or the Upper Mississippi lead and zinc district as it is also termed, lies in the southwestern corner of Wisconsin, and embraces adjacent portions of Illinois and Iowa. It includes Iowa, Grant, and Lafayette counties in Wisconsin, and Jo Davies country in Illinois. In Iowa, Dubuque formerly produced considerable lead, but there has been little mining there in recent years. The map, Fig. 1, shows the entire district, withroads, railways, streams, and the various towns, or "camps," around which the mines are clustered. The hatchwork indicates the areas in which lead and zinc have been mined. The district is about 60 mi. (96 km.) north and south and about 40 mi. (64 km.) east and west. Not all of the territory is mineral bearing, and there are considerable areas that are believed to be barren. The grouping of the mines is patchy and irregular, though certain broad zoncs of mineralization extend almost the full width of the district, as from Mineral Point west through Mifflin and Livingston, and from Shullsburg west through New Diggings and Hazel Green. It is worth noting that the best mines of the district have, to date, been found within 10 mi. ease or west of the fourth principal meridian line, thus lying within a long, narrow, north-and-south belt extending the length of the district. In a field as large as the Wisconsin, which has only within comparatively recent time been worked intensively for zinc, the chances are good for opening new and important orebodies in parts of the district not yet, or insufficiently, prospected. However; the prospecting has been most successful around, or adjacent to, the old lead diggings of nearly a century ago, and the camps that were well known then are still centers of activity. In their order of importance they are: New Diggings, Ben-ton, Mifflin-Livingston, Galena, Linden, Hazel Green, Shullsburg, and Highland. The district is one of the best farming districts in Wisconsin, with deep fertile soil. The farms are large and well improved, and the towns are modern and prosperous. Railroad facilities are good and proximity to Chicago is an asset. Mining is usually done on a leasing system of 10

Jan 1, 1920

By Charles S. Barrett

THIS paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstructures. About 12m exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,1 and a number of these have been selected to illustrate the results obtained. Prints are also included showing the common types of falsities-to borrow a term from the biological field, the "artifacts." In brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. n addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains. Since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. SPECIMEN PREPARATION AND PHOTOGRAPHS Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for repeated polishing and etching (each successive polish becoming less severe and each etch lighter), since the final etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and IC, the replicas used were of silica, deposited up0n polystyrene and floated from the polystyrene in ethyl bromide according to polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1943

By N. A. Ziegler

IN every research it is desirable to eliminate as many variables as possible and to leave only a few to be investigated one at a time. Metallurgical problems are no exception. Some of the variables that are difficult to control are the size, the distribution, and the orientation of the grains in a metallic test piece. It is therefore very desirable to obtain isolated metallic grains (single crystals, as they are commonly called) large enough to enable one to study their mechanical and physical properties. The present investigation is a part of magnetic research work on iron and iron alloys, undertaken to obtain, if possible, the magnetic properties of pure iron (Fe). This paper will deal primarily with the preparation of single crystals of iron and their mechanical properties, while another paper, by T. D. Yensen, now in preparation, will deal specifically with their magnetic properties. The work with "single crystals" is attracting more attention every year among the investigators in metallurgy. Van Liempt1 gives an interesting summary of the work done and the different methods used in the preparation of metallic single crystals. Briefly stated, the four principal methods used are the following: 1. The cooling of a liquid metal in such a way that the crystallization would start at one point only, causing the entire liquid to solidify as one crystalline unit. This method can be successfully applied to the majority of the metals that do not have any allotropic transformations in the solid state. It has been used and described by a number of investigators,2 but it has never been successfully applied to iron on account of allotropic transformations.

Jan 1, 1930

By Earl S. Bardwell

The structural relations existing between cuprous oxide and copper were first systematically studied by Heynl; who suggested that a study of the microstructure of refined copper might be substituted for the analytical methods in vogue for determining the oxygen content of copper coming from the refining furnace. Hofman, Green and Yerxa,2 in their paper A Laboratory Study of the Stages in the Refining of Copper, working along the lines suggested by Heyn, showed that a study of the microstructure could be made to yield a correct estimate of the oxygen content of refined copper. In order to determine the oxygen content of the specimen of refined copper under examination a photomicrograph was first made. From the relative areas of copper and eutectic, the percentage of cuprous oxide and the corresponding percentage of oxygen were then readily calculated. It was found that the values for oxygen thus obtained corresponded closely with the analytical results. With the idea of utilizing this method of determining the oxygen content of each charge dipped from the refining furnaces at the Boston & Montana Reduction Plant, the physical testing laboratory was equipped with suitable apparatus for carrying out the work. It may be of interest to describe certain of the methods which have been worked out in this connection and give such data as have been obtained bearing on the effect of the oxygen content of refined copper upon its conductivity. Apparatus.—For the benefit of those who may be unfamiliar with metallographical apparatus and methods and may be interested to know what equipment is required, a few words with regard to the apparatus are in place at this point.

Jan 1, 1914