Search Documents

By W. M. Robertson

The kinetics of grain boundary groove formation on copper surfaces immersed in liquid lead have been studied over the temperature range of 400° to 900°C. The groove widths were Proportional to the cube root of the annealing time, indicating that the diffusion of copper through the saturated liquid-lead solution is the mechanism by which grooves form. The rate constant for the process can be calculated by a theory due to Mullins. Using published data for the solubility of copper in liquid lead, for the interfacial energy of the solid copper-liquid lead interface, and for the diffusion coefficient of copper in liquid lead, the calculated rate constants almost exactly reproduce the measured values over the entire temperature range. The decay of scratches placed on copper surfaces has also been studied. The rate constant for scratch decay agrees with that for grain boundary groove growth, though scratch decay is sensitive to convection currents in the liquid. The interaction of solid and liquid metals has been studied extensively and has been found to be rather complex. Many of the studies have been complicated by a host of competing effects, including temperature gradients, concentration gradients, the formation of one or more intermetallic phases, natural or forced convection, and the presence in both the solid and liquid of considerable amounts of impurities and alloying elements. Recently theories have been developed of changes in surface profiles driven by capillary forces,' which allow the interaction of the solid and liquid to be analyzed quite directly. The present paper reports a study of the formation of grain boundary grooves on pure copper immersed in liquid lead, which allows the theory to be checked quantitatively. The Cu-Pb equilibrium diagram is quite simple: there are no intermetallic compounds, copper is just slightly soluble in liquid lead, and lead is almost completely insoluble in solid copper.2 The Cu-Pb system has been studied extensively,3-9 and all of the quantities—interfacial energy, diffusion coefficients, and equilibrium solubilities-necessary to calculate the rate of groove growth by a volume-diffusion mechanism are known. The kinetics of grain boundary grooving and scratch smoothing have been studied on the noble metals and the iron group metals in a reducing atmosphere or in vacuum.10 The main interest of these studies has been the determination of surface-diffusion coefficients at metal-gas interfaces using the theories developed by Mullins.1 The present paper uses similar methods for the study of diffusion processes at the interface between two condensed phases. There has been one previous study" of the kinetics of groove growth in a solid-liquid system, which, however, was troubled by the fact that neither interface energies nor diffusion coefficients were known in the Ni-S system studied. THEORY The theory of grain boundary groove growth has been developed by Mullins for the cases of volume diffusion," surface diffusion," and a combination of the two processes.14 He has also analyzed the kinetics of the flattening of a scratched surface by these processes.l5,l6 Several assumptions and approximations were used in the derivations of the surface profile shapes. The applicability of these assumptions and approximations to the present system will be considered in the discussion. At the intersection of a grain boundary with an initially flat interface the equilibrium between the interfacial energy and the grain boundary energy establishes an equilibrium groove angle. This induces curvatures in the interface. The chemical potential of material at a curved interface is higher than at a flat interface, so that material moves away from the region of the grain boundary. Mullins' calculations indicated that the groove profile would be similar to that shown schematically in Fig. 1. Small humps form above the level of the original flat surface. For a volume-diffusion mechanism the separation, w, of these humps at a time, t, is given by and where co is the equilibrium concentration of the solid in the liquid, y, the solid-liquid interfacial free energy, O the volume occupied by a solute atom in the liquid, D the diffusion coefficient of the solid in the liquid, and kT has its usual meaning. For a surface-diffusion mechanism the groove width is proportional to the fourth root of the time. For grooves forming by a combined surface and volume-diffusion mechanism the exponent of the

Jan 1, 1965

By William L. Fink, L. A. Willey

Since so many different curves have been published for the solid solubility of zinc in aluminum, it seems desirable to definitely establish the correct curve by two or more independent methods. The curve published in part I1t was based entirely upon X-ray measurements because the other methods employed at that time were not satisfactory. The present paper (the seventeenth of this series on high-purity aluminum alloys) describes the determination of the solid solubility of zinc in aluminum by the measurement of electrical resistivity at temperature and by microscopic examination. Since the publication of our part I in 1932, an investigation of the solubility relations in the aluminum-zinc system has been reported by Schmid and Wassermann2, who obtained their solubility results from lattice-parameter measurements on heat-treated and quenched specimens. The diagram that they published is shown in Fig. 1. In this investigation they also found by X-ray measurements that the parameter of the gamma phase changed continuously with zinc content and at such a rate that it would be identical with that of the beta phase at 60 atomic per cent zinc. It was concluded therefore that the beta and gamma phases, from the point of view of structural relationship, are one single phase. They also suggested a gap of immiscibility between 270" and 350" C. The complete boundary in this region could not be determined satisfactorily by the method employed and therefore was not shown in their diagram. Aluminum-zinc Alloys Materials Used.—Electrolytically refined aluminum3 was used in preparing the alloys for the work reported in this paper. Chemical analysis showed the following impurities: 0.004 to 0.005 per cent silicon, 0.006 to 0.008 per cent iron and 0.005 to 0.006 per cent copper. Also,

Jan 1, 1936

By Lawrence Addicks

(San Francisco Meeting, September, 1915) THROUGH the courtesy of Dr. James Douglas I am permitted to give, a summary of some of the results obtained in leaching slimes tailings in a series of experiments conducted under my direction at Douglas, Ariz.. during the past year. While the test run for which the data are given deals with a particular case, much of the work is general in its application and may therefore be of interest. This work was done upon the ores of the Burro Mountain Copper Co. A description of the geology of the district will be-found in the paper by R. E. Somers published in the May, 1915, Bulletin of the Institute. The mineral is pyrite and chalcocite very finely disseminated throughout the gangue and a characteristic of all the ores is the large amount of alumina present. A representative analysis of the particular ore under consideration would be about as follows: Cu, per cent 2.35 S, percent 3.0 Ag, ounces per ton 0.05 CaO, per cent 0.5 Au None K202, per cent 4.0 Fe, per cent 1.5 SiO2, per cent 70.0 A120,, per cent 13.0 The leaching of the ore direct was early dismissed from consideration for the following reasons: 1. The ore would have to be quite finely crushed to liberate the mineral for leaching; concentrating after crushing would cost but a few cents a ton; and a higher total recovery would result from leaching tailings rather than ore. 2. Rough concentration would yield a suitable material for roasting to make sulphur dioxide or sulphuric acid in connection with the leaching scheme. 3. Such a program put the question of cost vs. recovery on a basis where flotation and discarding of tailings were directly comparable.

Jan 8, 1915

By L. E. Murr, P. J. Smith

A study has been made by transmission electron microscopy of thin foils of 304 stainless steel fatigued external to the electron microscope in reversed bending, and of thin foils fatigued directly within the microscope in alternating tension. The build-up of stacking faults in the thin foils during fatigue zoas correlated with the dislocatirm structures found in thin films prepared fror fatigued bulk specimens. The performance of the special devices designed for fatigue of thin foils so outlined and the importance of alternative methods of preparation of more uniform fatigue specimens bY vapor deposition are emphasized. INVESTIGATIONS on fatigued bulk aluminum1,' and stainless stee13j4 have revealed the existence of dislocation substructure on examination by transmission electron microscopy of electrolytically thinned foils representative of these bulk specimens. While this technique has proved extremely valuable, it has several shortcomings. First, the method of fatiguing bulk specimens and then thinning to foil for electron-transmission observation allows only one observation of internal structure at any one portion of the fatigue life. Second, thinning the bulk fatigued specimens to foil results in the loss of at least one original surface. Thus, what one sees in the remaining electron-transparent sections is an internal dislocation or fault structure which in many cases cannot be correlated with the original surface markings. This is an undesirable feature, since it is well-known that metal surfaces play an important part in the fatigue process.5 An obvious third undesirable feature of the thinning-from-bulk technique is the fact that static observations have difficulty (in the case of fatigue) explaining the mechanism of a dynamic process. What is required then is a method whereby a selected thin area can be continuously observed either while undergoing cyclic deformation or at various fixed stages of fatigue deformation. While Murr and wilkov6 have reported some success with an apparatus designed to fatigue thin metal foils directly within the electron microscope, the nature of the specimen-mounting procedure and the mechanical features involved in the adaptation of the fatigue device to the electron microscope make this method difficult to operate. It was not possible, for example, to make frequent observations of a selected area because of difficulty in maintaining a chosen area in a stable viewing position inside the electron microscope. Except for the build-up of a dislocation substructure and what are commonly referred to as "slip striations", little else has been reported from observations on thin-foil sections prepared from bulk fatigue specimens. segal17 has found "slip striations" in stainless-steel fatigued specimens which were electropolished from both sides, but gave no explanation as to their origin or identity in terms of lattice imperfections. The research to be reported in this paper was undertaken with the following objectives in mind. First, an attempt was made to devise a technique or techniques whereby thin metal foils could be fatigued and repeatedly observed by transmission electron microscopy. Second, it was hoped that some correlation could be made between deformation striations found in fatigued thin transmission specimens and thin foils prepared from bulk fatigued specimens. These investigations illustrate quite convincingly that a feasible method is available for the direct study of the fatigue mechanism and similar dynamic phenomena in thin transmission specimens inside the electron microscope. I) EXPERIMENTAL METHODS Three modes of specimen fatigue and observation of fatigue damage were used. These involved fatigue of thin-foil specimens in a special arrangement external to the electron microscope and observation of a selected area at various stages in the fatigue life, the fatigue of thin-foil transmission specimens inside the electron microscope, and the fatigue of bulk specimens external to the electron microscope followed by thin-foil preparation for direct observation at predetermined stages. Design of the External Fatigue Clip and Specimen Holder for the Hitachi H.U.11 Electron Micro-scope. The purpose of the fatigue clip was to provide a reversed bending fatigue stress to a thin-foil transmission specimen outside the electron microscope. In order to accomplish this, a flat-bottomed, U-shaped brass clip was made as shown

Jan 1, 1965

By C. G. Dunn, F. Lionetti

The energy associated with grain boundaries in polycrystalline aggregates is believed to play a major role in grain growth processes and, when growth ceases, to determine the final equilibrium grain boundary angles. Further, the energy of grain boundaries of recrystallization nuclei is a factor in nucleation processes. It is important to know, therefore, how the energy per unit area of a grain boundary, that is, the grain boundary surface tension y, depends on the difference in orientation of the two lattices of the grains producing the boundary. Although the problem is important, surprisingly little has been done toward a quantitative evaluation of the effect of orientation difference on grain boundary energies. C. S. Smith1 recently has discussed this problem and in addition to showing effects of orientation difference on equilibrium angles has shown a variety of interesting effects of surface tension on the appearance of microstructures. Fig 1 and the following relations expressed in Eq 1, which connect equilibrium grain boundary angles and surface tensions, illustrate equilibrium conditions which are believed to hold true in metals. ?l2 _ ?23 _ ?l3 [1] sin ?3 sin ?1 sin ?2 Clearly any two of these surface tensions can be expressed in terms of the third when the equilibrium angles ?1, ?2, and ?3 are known. Applied to the present problem for solid state equilibrium of three grains, the angles ?1,?2 and ?3 must be measured in a plane perpendicular to the line of junction of the three grains. Normally a direct determination of these angles from random microsections is impossible. Consequently Harker and Parker2 and Smith1 (except for some measurements on flat specimens) resorted to a statistical method to determine equilibrium grain boundary angles. Smith reported that grain boundaries meet the surface of a piece of metal nearly perpendicularly. He reported also, in connection with direct angle measurements on flat specimens with grains extending through the thickness, that angles varied appreciably from 120" and concluded that there was a measurable effect of orientation difference on surface tension. Another direct way of determining equilibrium angles and a method adaptable to studying particular configurations, recently suggested by Dunn,³ is to use a three-grain flat specimen with orientations of grains so chosen that the junction line of the three grains will be straight throughout the thickness and perpendicular to the surface of the specimen. Choice of orientations is possible when individual grains of each group can be grown to predetermined orientations through the reorienting and growth of " seed crystals " as described.³ Not only is it possible, for example, to have grains with the same crystallographic plane in the plane of the specimen, but a given orientation difference between two grains can be made a common factor to an unlimited number of three-grain groups while a series of orientation differences is investigated. Any effect of anisotropy of gas-solid surface tension due to grain orientation should be minimized by having all gains oriented the same with regard to crystallographic plane in the plane of the specimen. Another feature of the three-grain group is the notched grain boundaries as shown in Fig 2 for one specimen (S4). The notches serve to anchor the end positions of the grain boundaries (especially at high temperatures) while the central and junction point of the grains moves toward an equilibrium position. Final equilibrium should produce straight grain boundaries if the notches are very narrow and if changes in orientation* of the grain boundary do not alter the surface tension.† If one assumes the straight line condition and no change of surface tension with small changes in grain boundary orientation and finds the equilibrium configuration by a minimization of the grain boundary energy, one obtains the relations given in Eq 1. The approach to straight line boundaries or to minimum energy configurations in specimens containing large grains, such as those used in the present investigation, may be very slow compared with the approach to equilibrium conditions for the grain boundary angles. It may be desirable, as proved to be the case in the present investiga-

Jan 1, 1950

By E. Wainer, K. D. Burnham

A wet beneficiation technique for producing wollas-tonite from its ore in high yield and purity has been evaluated in a pilot plant operation at the rate of 75 tons per month. Finely crushed, unsized wollastonite ore mixed with water is passed through a high in tensity oscillating wet magnetic separator of unique design and in a single pass over 90% of the wolla-stonite exhibiting a crystal purity of 99.8% is obtained irrespective of size of feed fraction. Thereafter, the material is processed by closed cycle standard wet milling and classification techniques to yield a 1µ size product, though any mesh size up to and including 50 mesh may be obtained, if desired. Costs appear to be significantly lower than those available from dry processed techniques. Wollas tonite made by this unusual wet process appears to have potential utility in the following fields: ceramics, paints, plastics, paper, organic finishes, reinforcement of portland cement items, controlled porosity refractory ceramic foams, cinder and concrete block paint, and the like. The 1µ and certain chemically processed varieties of wollastonite may have unusual utility in the paper industry both as a filler and as a coating material and in the organic finish industry. Extensive deposits of wollastonite ore equivalent to an average tenor of 50% to 60% of this latter mineral in easily separable form exists in and around Essex County in northern New York State in reserves of the order of several tens of millions of tons. While important portions of these deposits are susceptible to open pit mining techniques, one operation near Wills-boro, N.Y., involves tunnel mining and dry milling and beneficiation techniques. This mill and tunnel mine is presently being operated by The Cabot Corp. and a variety of particle sizes are now sold into markets in the ceramic, paint, plastic finish, floor tile and in similar fields in substantial tonnages on a repetitive basis. Serious investigation and study over the past several years has indicated that, outside of the obvious economies of open pit techniques for mining purposes, wet beneficiation and milling procedures applied to the ore not only represent a potential for greater economies in the production of a superfine finished product but yields products of improved properties exhibiting increased market potential which may not be available from the dry ground product. The Lewis and Deerhead deposits, controlled by the Adirondack Development Corp., appear to be identical to the Wilisboro deposit. Utilizing ore taken from the Lewis and Deerhead deposits, a pilot plant process for the wet beneficiation, milling and classifying of wollastonite ore has been operated for several months. After scalping a marketable garnet product from a minus 16 mesh dry crushed feed on a high intensity roll magnet the balance of the material is then roll crushed in a closed cycle until it will pass a 50 mesh screen. The product constitutes the feed of the wet magnetic separator. The heart of the new beneficiation process is a cyclically operated wet magnetic separator which exhibits the unique feature that unsized feed is easily handled. Product yields of higher purity are equal to that obtained with dry magnetic separations which use closely sized dry ore and multiple passes, but only produce wollastonite of about 98% mineral purity as determined by sink float techniques. It was anticipated that the wet processing through the grinding, milling and classification stage would yield a low cost 1µ ground product which should make available greatly increased applications for the mineral beyond those presently enjoyed. The improved purity was also expected to provide coarser sizes which might be utilized as a raw material for chemical modification which again would expand the uses of wollastonite. The evidence thus far collected appears to indicate that this premise may be expected to be fulfilled. There are on the surface of wollastonite particle sites at which cheinical reactions may occur1. It is believed that wet ground material provides a better base which will allow wollastonite a deeper entree into the field of chemical raw materials. Wet ground at 20µ and finer permits with certainty a number of chemical reactions, some of which are mentioned later in this article. While well crystallized wollastonite makes up the majority of the ore, the balance consists mainly of very weakly magnetic diopside of the hedenbergite-

Jan 1, 1965

By K. G. Davis, P. Fryzuk

The diffusivity of silver in liquid tin has been determined, using the capillavy-reservoir technique, over the temperature range 250° to 500°C. The new value, D = 2.5 x 10'* exp(-2480/ RT) sq cm per sec, differs from that obtained by other workers in an earlier investigation. The analysis of data from the capillary-reservoir technique is discussed. In a recent investigation of the solidification of dilute alloys, values for the diffusion constant of silver in liquid tin were required in the analysis of the formation of impurity substructures. AS a result, measurements were made of the diffusion constants in the temperature range 250° to 500°C (melting point of tin 232°C), for the alloy concentrations used in the solidification experiments and at higher concentrations, to verify previous determinations.I)2 The capillary-reservoir method was adopted, using experimental procedures similar to those followed by Ma and Swalin,1 with the main exception that radioactive silver was used in the present investigation to facilitate solute-concentration measurements. EXPERIMENTAL PROCEDURE a) 100 ppm Samples. Glass capillary tubes of 2 mm inside diameter and approximately 5 cm- long were sealed at one end, evacuated, and filled with tin of 99.999 pct purity. The region of shrinkage near the mouth was cut off, and the tubes were then placed in a graphite holder and immersed, with the open end up, in an unstirred bath of alloy containing 100 ppm Ag 110, where they remained for periods of up to 30 hr. On removal from the bath they were cooled by an air blower. The bath was kept under a small positive pressure of argon, and the temperature controlled to within +1°C. A 10-hr diffusion period was used in the majority of the tests, scatter on runs of less than 5 hr being rather large. The procedure outlined above was chosen in preference to putting alloy in the capillary and pure tin in the bath, in order to avoid segregation when the tubes filled with alloy were first solidified. To minimize segregation when the diffusion period was complete and the capillaries again solidified, the earlier samples were held in thin-walled silica tubes which could be cooled very rapidly. Later tests were made in precision-bore Pyrex tubes, to eliminate effects caused by variations in the capillary diameter. No consistent differences in diffusivity as measured in the two types of tube were detected. After removal from the glass tubing, the samples were sectioned into 2.5 mm lengths and counted for y activity, using a scintillation counter with fixed geometry. Samples were also drawn directly from the bath and counted, so that values for C/C,, the ratio of the weight of Ag 110 in the sample to that in the bath, could be obtained. b) 5000 ppm Alloy. To check for possible effects of concentration, the silver content of the bath was increased to 5000 ppm. Complete mixing was found to have taken place in the capillary after a 10-hr period at 300°C. It appears that the greater density of the alloy was sufficient for buoyancy forces to cause instability in the alloy-tin interface, leading to rapid convective mixing. For the 5000 ppm alloy, therefore, the bath was of pure tin and the capillary tube was filled with alloy. With this arrangement, values of D consistent with those for the 100 ppm alloy were obtained, Fig. 1. CALCULATIONS OF DIFFUSIVITY The terminology used applies to a capillary of pure tin immersed in a bath of alloy. 1) Error-Function Method. under the present experimental conditions, the rod of liquid tin into which silver is penetrating may be considered semi-infinite. Assuming the concentration at the mouth of the tube to remain constant at Co, the concentration C at distance x from the mouth of the tube at time / is given by3 Plots of the inverse error function of (1 -C/Co) vs .v gave straight lines passing through the origin with slope 1/2-, x being corrected for shrinkage both on solidification and while cooling to the melting point (total correction about 6 pct at 500°C). Values for log D obtained in this manner are shown in Fig. 1. A least-squares fit to the relation D = Do exp(-Q/RT)

Jan 1, 1965

By A. T. Corey, C. H. Rathjens

INTRODUCTION Although the oil industry has been aware of the directional variability of permeability in porous rock, the directional variability of relative permeability has been largely ignored. Yet it is apparent that such an effect must be present in a system in which the distribution of oil and gas within the porous matrix is controlled by capillary forces. It is easy to visualize a rock composed of layers of fine and coarse material such that gas flow across the bedding planes would take place only after the average oil saturation had been reduced to a very low value. The fine layers, because of their greater capillarity, would remain saturated and act as barriers to the flow of gas after the coarse layers had been desaturated. Flow of gas parallel to the bedding planes would obviously take place at a much greater liquid saturation. Without more complete information concerning the geology of a reservoir than is generally available, it is not possible to predict exactly how such phenomena would affect the over-all performance of an oil field. It is possible, however, to predict qualitatively the effect of stratification on relative permeability measurements made on laboratory cores. In this investigation the effect of stratification was studied analytically by assuming that two porous materials with different capillary pressure-desaturation curves (but identical relative permeability curves) were in contact and in capillary equilibrium. As a qualitative check on the analytical results, cores having various degrees of visible stratification were used for relative permeability measurements made with fluids flowing both parallel and perpendicular to the bedding planes. A quantitative check was considered impractical because of the difficulty of devising models in which two materials of predetermined properties could be joined without the plane of contact becoming a discontinuity. THEORETICAL CONSIDERATIONS AND ASSUMPTIONS The assumption of capillary equilibrium in an oil-gas system implies that the difference in pressure between oil and gas is everywhere the same. This means that the curvature of the interfaces must be everywhere the same in order to satisfy the equation where PC is the pressure difference between phases, y the interfacial tension and r, and r2 are the major and minor radii of curvature. Depending on the pore size distribution of coarse and fine layers, the volumetric percentages of oil and gas in these layers will differ when equilibrium exists. The exact relationship can only be determined by obtaining the complete capillary pressure-desaturation curves for each of the porous materials in contact. It has been pointed out elsewhere' that the capillary pressure-desaturation curves of sedimentary porous materials can often be approximated by the relation where C is a constant and Soe is the effective saturation to oil based on a percentage of the pore volume effective to flow. In the same paper it was indicated that, as a first approximation, the values of oil relative permeability are given by and the values of gas relative permeability by For this analysis Eqs. 2, 3, and 4 were assumed to apply to each of two components of a hypothetical porous rock in capillary equilibrium. It was also assumed that each of the components had a residual wetting phase saturation of 20 per cent so that 80 per cent of the total pore volume was effective to flow. The permeability of the coarse stratum was taken as 100, and its displacement pressure was such that C in Eq. 2 had the numerical value of 1. The corresponding values for the fine stratum were 10 for the permeability and 10 for C. Units are not specified because they do not enter into the final results. The choice of the permeabilities and displacement pressure ratios was made to expedite the calculations. Any reasonable rock properties could have been chosen without changing the results qualitatively. Several arrangements of the two components were studied. Table 1 summarizes the resultant permeabilities obtained for four types of arrangement. RELATIVE PERMEABILITY CALCULATIONS The first step in the computation of relative permeability for the composite cores was the plotting of the capillary pressure-desaturation curves and the relative permeability curves for the individual components according to Eqs. 2, 3, and 4. At arbitrary

Jan 1, 1957

By Alan Stanley

THE MacIntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.' Pigment plant production demands that the MacIntyre mill produce a 44.7 pct TiO, ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the MacIntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from • one level to the next. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO, has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO, has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the MacIntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO, was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiOz a constant gravity would invariably be obtained, and as the TiO, value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct Ti02 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO, value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO, and as the specific gravity increased the trend was for the TiO, assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1953

By Alan Stanley

THE MacIntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.' Pigment plant production demands that the MacIntyre mill produce a 44.7 pct TiO, ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the MacIntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from • one level to the next. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO, has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO, has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the MacIntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO, was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiOz a constant gravity would invariably be obtained, and as the TiO, value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct Ti02 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO, value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO, and as the specific gravity increased the trend was for the TiO, assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1953

By A. G. Guy

Thermodynamic activity rather than chemical composition is basic to the analysis of diffusion. This is the essential conclusion reached by Darken1-3 and by Birchenall and Mehl.4 If so, it is reasonable to expect that diffusion calculations should be carried out using activities. This paper will illustrate a method of employing activities in analyzing interstitial diffusion. For interstitial diffusion (of carbon in iron and probably generally) the diffusion of the solvent atoms, volume changes, and other such complexities not explicitly provided for in the usual diffusion equations cause a negligible error of the order of 1 pct. Therefore it is relatively easy to test the validity of an analysis based on activities in the instance of interstitial diffusion. The mathematical treatment of the more complex substitutional diffusion could be simplified once the adequacy of the activity method had been established for substitutional diffusion. Thus the present work has the purpose not only of providing a superior analysis of interstitial diffusion but also of indicating a possible approach to the more important question of an adequate treatment of substitutional diffusion. Development of the Diffusion Equation Although activities are convenient quantities to determine experimentally, they are derived from the more fundamental fugacities.9 Possible confusion in using activities can be avoided by basing equations involving their use on the relationship, dP = -D1d/ax dt [I] where, dP = the number of grams of solute crossing one cm2 in the time dt sec. D, = the diffusion constant for use with fugacities; it is assumed to be constant at a given temperature, and has units of secs. f = the fugacity of the solute in the solid solution; the units are those of pressure, dynes per cm2. x = the distance in cm. Eq 1 can be considered to be the basic form of the first Fick Law for one-dimensional diffusion. In order to convert Eq 1 into an equation involving activities, a choice of a standard or reference fugacity, f°, must be made: then. a = f [2] where a is the activity corresponding to the fugacity f. However, the value of a is also determined by the relation, a = a\c [3] where a is the activity coefficient and c is the concentration. For a given value of a (such as a = 1) it is evident that the units used for expressing concentration will affect the numerical value of a corresponding to a given amount of carbon dissolved in y-iron. Since weight per cent concentration is so widely used, this unit will be adopted as the standard in this paper. When the value off given by Eq 2 is substituted in Eq 1, the first Fick Law becomes, dP= -D,f°dl [4] Since D,f° is constant (at a given temperature), the second form of Fick's Law can be obtained in the usual manner, -dt D'f° dx [5] where c' is the concentration in g per cm3. In terms of weight per cent concentration, c, Eq 5 becomes, dc _ 100 d2a Tt = T /f w [6] where p is the density of the solid solution and will be assumed to be constant. In order to simplify Eq6, it is necessary to consider the standard state, f°. Standard states are chosen for convenience. There appears to be one especially convenient choice for the analysis of interstitial diffusion. If the activity coefficient, a, is set equal to unity at infinite dilution of the solute, 100 then — 100D1fl° is approximately equal P to the usual diffusion constant in dilute solutions. This is true since the activity, a, in Eq 6 can be replaced by the concentration, c, with little error in an infinitely dilute solution.* Here f1° is the standard fugacity necessary to achieve this standard state. It is proposed that a diffusion constant Da' be defined, Da1=100/pD1f1° [7] where A is the metal whose diffusion is * The second derivative of a is equal to the second derivative of c in dilute solution only if -da/dr- is. zero. Although theory does not require this condition, in the systems C in Fe, and Zn in Cu, dc is in fact found to be essentially zero.

Jan 1, 1950

By G. Osuch, G. Derge, G. M. Pound

Using a new dternating-current potentiometer circuit and a specially designed four-terminal cell, the specific conductance of molten Cu2S-FeS mattes was measured as a function of temperature, from the liquidus to 1500°C, over the complete range of composition. The high conductivities, about 1500 ohm-I cm-l for FeS and 100 ohm-l cm-l for Cu,S, indicate that the conduction is electronic rather than ionic. Molten FeS has a negative temperature coefficient of specific conductance, resembling metallic conduction. Molten Cu,S has a positive temperature coefficient, resembling semiconduction. The binary roughly follows an additive rule of mixtures with respect to both magnitude and temperature coefficient of specific conductance. Metallic bonding in the liquid is postulated to explain these phenomena. MUCH has been learned in the past about the nature of liquids and the ionic or molecular species in solution by means of electrical measurements. Thus, dielectric constants','2 have given information about molecular liquids such as water and benzene. Measurements of dielectric constant usually are impossible in electrically conducting liquids, such as aqueous solutions of ionic salts and molten ionic salts. However, measurements of electrical conductance and ionic transference have provided much knowledge about the latter systems.a-" In recent years, the ionic nature of certain molten metallurgical slags has been established by Derge and Martin7 through electrical conductance and electrolysis measurements. Chipman, Inouye, and Tom-linsonq ave studied the electrical conductance of molten FeO and report a high specific conductance of about 200 ohm-' cm-' (compared with 4 ohm" cm-' for an ordinary ionic liquid such as molten NaCl) and a positive temperature coefficient of conductance. They interpret these results in terms of p-type semiconduction by analogy to the situation in solid FeO.Y imnad and Derge" have studied cell efficiency in the electrolysis of molten FeO-SiO, systems and conclude that ordinary ionic conductance increases with SiO, content. Very recently, interest has been revived in the electrical conductance of liquid metals and liquid metallic solutions. Scala and Robertson1' report a close resemblance between the liquid and solid states with respect to thermal, structural, and compositional relationships. Molten sulphides have not received a great deal of attention. Bornemann and von Rauschenplat" measured the specific conductance of molten Cu2S as a function of temperature with a four-terminal cell using direct current. A high specific conductance and a positive temperature coefficient were found in that investigation." Using a two-electrode apparatus, Savelsberg" electrolyzed various molten sulphide mixtures. He concluded that pure molten Cu,S and FeS were electronic conductors but that the mixtures exhibited some ionic conduction. In the present investigation, the specific conductance of the industrially important Cu-Fe sulphide mattes was measured as a function of temperature and composition in order to investigate the mode of electrical conduction and the structure of these molten mattes. An alternating-current circuit was used to eliminate the effect of any possible electrode reactions. Apparatus The Conductance Cell: Due to the high specific conductance of the systems studied (10' to 10" ohm-' cm-'), the classical two-terminal cell and Wheat-stone bridge apparatus could not be used. A four-terminal cell was developed in order to eliminate lead resistance, and an ac potentiometer circuit was designed to give rapid and sufficiently accurate measurements of the cell resistance. A diagram of the conductivity cell is given in Fig. 1. The molten matte is contained in a dense alundum crucible, and spectrographic graphite rods that dip into the molten matte serve as the four conductance terminals. Two of the graphite rods on opposite sides of the cell serve as current-carrying leads, and the other two graphite rods are null-current probes that detect the potential drop across the cell. These graphite rods are contained in silica tubes, and the lower constricted portions of the two silica tubes define the column of liquid whose electrical resistance is being measured. The electrical resistance of the broad ex-

Jan 1, 1956

By G. S. Hume

Activity in geological exploration and drilling continued in Canada in 1945 at about the same rate as in the previous year, but with disappointing results as far as new production is .concerned. Both in the foothills and on the Plains of Alberta, however, there are wildcat wells that have either given encouraging shows or some production, which are very important in relation to future developments. The normal decline of Turner Valley, the largest producing field in Canada, has continued, and this decrease has not been offset by new discoveries. In addition, the closing of the Canol pipe line on March 31, 1945, isolated the Norman Wells field in the Mackenzie River valley, and the outlet at present. is confined to supplying the relatively small local requirements. This

Jan 1, 1946

By A. E. Bellis

The time effect in reheating certain steels below the critical range is very marked. The increased toughness, shock-resisting power, and machinability of steel subjected to a long, high drawing temperature has been thoroughly demonstrated and is of practical importance, particularly in the manufacture of L'smokeless" rifle-barrel steel. The time effect in tempering is most important when a maximum drawing effect is desired, in which case the highest physical properties as well as ease of machining are important considerations. These are the conditions in drilling a rifle barrel. A hole, 0.30 in. in diameter and 24 in. long for the Springfield rifle, and 30 in. long for the Russian military rifle, has to be drilled in the heat-treated material. This barrel-drilling operation is probably the most difficult one in rifle manufacture, and anyone who has been connected with rifle manufacture knows how seriously production is affected when "hard" or non-uniform steel for barrels is encountered. The importance of high physical properties (tensile strength, toughness and resilience) in a rifle barrel is obvious. The physical properties of two different lots of barrel steel are given below. The first lot, No. 1, gave serious trouble in the drilling operation; the second gave no trouble at all. No. 1 No. 2 Elastic limit, lb. per sq. in.................... 117,450 116,800 Tensile strength, Ib. per sq. in................. 132,500 131,750 Elongation, per cent........................ 16.0 20.0 Reduction of area, per cent................... 42.1 51.0 Impact strength, ft.-lb. per sq. in.............. 450.0 520.0 This difference in machining and physical properties was due entirely to the time of reheating. The first lot was given a reheating time of 30 min., the second lot remained at the reheating temperature 2 hr. Both

Jan 1, 1918

By Frank Firmstone

The material described below was made at Furnace No. 2, Longdale, Va., Oct. 28, 1907, during a sudden derangement of working, in the course of which the furnace became entirely bridged over and for some time no solid material whatever descended into the hearth. This caused the hearth to become so completely emptied that, at the tuyere-level, a pricker put in at one tuyere could be seen by looking in at the opposite one. The tap-hole was opened and the iron got out with some difficulty. It ran sluggishly, throwing many sparks, but was not too thick to run into the chill-molds. Naturally, the product was assumed to be white iron, which is almost always produced under similar circumstances; but on removal front the molds it proved to be very strong and tough, although full of blow-holes. Most of these blow-holes bad bright, unoxidized walls. The iron could be drilled by using a "special steel" drill, the drillings curling up similarly to those of steel. An analysis by P. W. Shimer of this unusual product gave: Si, 0.019; P, 0.228; S, 0,39; Mn, 0.042; C, 2.366; and graphite, 0:000 per cent. A cast of iron made just before the disturbance contained P, 0.98, and Mn, 1 per cent. The peculiar product seems to have been decarburized in the hearth and, at the same time, to have lost much phosphorus and manganese, either by the action of the blast in the empty hearth, or, more probably, by. contact with the cinder rich in iron which was formed at the time. Unfortunately, no specimen of the cinder was preserved, so its composition cannot be given. It seems very remarkable that, with the furnace in bad condition, the temperature should be high enough to keep such

Sep 1, 1908

By James L. Poole

INTRODUCTION Companies in the mining industry are subjected at times to currency exchange rate risks and interest rate risks. The former occurs any time a firm deals in more than one currency. The latter occurs anytime a firm is financing itself with borrowings that have a floating interest rate (although a fixed rate can be a problem at times). FOREIGN EXCHANGE RISKS There are two general reasons why exchange rate risks (FX risk) can occur: First, a firm may be building a mine or plant in another country where financing for the plan is denominated in funds other than the country hosting the plant. For example, if a Canadian firm is building a smelter in another country which is being financed with Canadian dollars, the C$100 million for labor, which must be paid in the local currency, has subjected the firm to a C$100 million FX exposure risk. If after the cost estimates were made the local currency appreciates 30% against the Canadian dollar, the cost of labor has increased to C$130 million. (Of course, the local currency could also devalue during this period making the labor cost component less than estimated.) The other reason exchange rate risk arises is due to the fact that the costs of production in one country producing minerals may be incurred in one currency while the production is sold in another currency, such as coal being exported from Canada to Japan under contracts denominated in Yen. In this example, the Canadian firm is exporting coal to Japan and being paid in yen in 30 days at a contract price of 100 Y per ton. Furthermore, assume that the mining firm anticipates a depreciation of the yen against the Canadian dollar of 5% in the next 30 days. Therefore, the mining firm stands to lose 5% of the value of its shipment in a month's time not including carrying costs. In both cases, the mining company risks an adverse change in the exchange rate, that is, the currency the company holds may decrease in value relative to the other currency. There are a number of ways to mitigate the exposure to foreign exchange which can be utilized by the mining company. Optimally, a company should try to match all their inflows and all their outflows in the same currency. For example, if a Canadian firm has mining costs and debt service costs both denominated in Canadian dollars then 100% of their receipts would need to be in Canadian dollars. If a Canadian firm has 70% of its cash outflows in Canadian dollars and 30% of its cash outflow in American dollars in the form of a loan amortization then their receipts would need to be 70% in Canadian dollars and 30% in U.S. dollars. This general principle of matching cash receipts and cash costs in the same currency works fine in a perfect world but what of the real world when these cannot be matched? In actual practice, however, the financial markets have developed a number of ways in which foreign exchange risks can he managed or reduced. FORWARD MARKETS One method is to use the forward markets which are made on a world-wide basis by the commerical banks for foreign exchange. If a firm wanted to lock in the current exchange rate for the receipt of a foreign currency at some point in the future, they could do so by contracting on the forward market with a bank selling that foreign currency at the current rate at the future date. For example, assume that a Canadian firm is exporting coal to Japan which would pay yen in 90 days. If a firm wanted to lock in today's exchange rate they could contract with a bank to sell on the forward market yen in 90 days. When the yen was received the contract would be executed by selling the yen to the bank and receiving the previously agreed upon number of Canadian dollars. Generally speaking, the forward market can be used to sell forward about 12 months. The costs of selling (or buying) forward

Jan 1, 1985

By M. H. Shumate

Rope-type haulage has had many applications in the mining and allied industries. Records have indicated favorable results both from a standpoint of efficiency and investment. The Truax-Traer Coal Co. has used some variations of rope haulage at their mines and preparation plants. They have built a system which solves their particular problems, and have an investment which has indicated an annual savings in operating costs. Rope haulage, as applied to the mining industry, goes back many years for both underground and surface mining, or a combination of both. The Truax-Traer Coal Co. has used gravity retarding hoists as well as several variations of rope haulage, including electrical and combinations of both, but each was limited in its use and application by natural conditions and economies of the operation. Several systems of rope haulage equipment are offered by manufacturers today for handling railroad car movement on a limited or continuous basis. The portal and railroad loading facilities of Truax-Traer Coal Co.'s Burning Star Slope mine, located in Jackson County, Ill., were moved in 1960. The old location was abondoned, eliminating 3% miles of underground track haulage. The mine was converted to an all-belt system, and coal is loaded at a new raw coal plant and shipped by railroad cars to a central cleaning plant. The company wanted to operate the surface facilities as efficiently as possible, employing a minimum number of workers, using the latest type railroad car movers. The existing rope haulage facilities at several locations throughout the country were examined and considered for the Slope mine location. The application of each appeared favorable but lacked flexibility, and it was difficult to justify the capital investment. The company decided to investigate the possibility of building a system that would apply to their problem, and have an investment that could be amortized in a relatively short period. SPECIFICATIONS They employed the services of Allen and Garcia Co. of Chicago, Ill. Through combined efforts, a railroad car rope system was designed to specifications as shown in Fig. 1. The Falk Corp. of Milwaukee, Wis. built the hoist to the specifications as shown in Fig. 2. It has an all welded base and pedestals. The all welded drum is not grooved. A single helical gear was used in lieu of herring bone type. A Falk speed reducer, Unit 90Y3-A, is driven by a 25-hp 1800-rpm, 440-V ac type 'C' (high starting torque) drip-proof, Frame 324-U motor. The speed reducer shaft is equipped with a solenoid operated ac spring set shoe brake, operating on a 7-in. diam. brake wheel. The dolly car, shown in Fig. 3, was field constructed, using the trucks and frame of a railroad tank car. Truax-Traer did not alter the frame but added plates and anchors for hoist ropes and frames for 8.5 tons of concrete to be used as ballast on the car. The limit switch operating shoe was also installed and the car coupler latch mechanism overhauled. The hoist rope selected was 1% in. in diam., 6x37 improved plow steel extra flexible, right lay, regular lay, with independent wire rope core, and preformed. Wedge sockets were used to connect rope to the dolly car as shown in Fig. 4. The system employs two 30-in. and three 16-in. diam. sheaves. All are bronze bushed and equipped with grease fittings. Larger sheaves are used for directional change of hoist rope and the smaller ones as snub sheaves to correct fleet angle of rope as it approaches the hoist drum. The Trench lay cable, buried between the two tracks, is used for electrical distribution and controls between hoists and operator's cab. Foundations for the system required 187 cu yards of reinforced concrete using approximately 60 cu yd each at three locations. Four hoists are employed in the system, two for each track. A pair is interconnected electrically and when one operates, moving the cars, the tail hoist idles with brake released. The process is repeated for the reverse direction. A limit switch, mounted in the track near each end of the system, is tripped by the dolly car as it approaches the hoist. The limit switch controls movement in one direction only, protecting the dolly car and establishing positive con-

Jan 1, 1962

By Alan Stanley

THE Maclntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.1 Pigment plant production demands that the MacIntyre mill produce a 44.7 pct. TiO2 ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the Maclntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from one level to the next.. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the, physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO2 has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO2 has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the Maclntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO2 was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiO2 a constant gravity would invariably be obtained, and as the TiO2 value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct TiO2 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO2 value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO2 and as the specific gravity increased the trend was for the TiO2 assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. [ ] Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1952

By William C. Aitkenhead, John A. Jaekel

Uranium deposits in the Spokane Indian Reservation, as well as those around Mt. Spokane, are essentially low grade, much of the ore containing less than 0.2 pct U808. The Mining Experiment Station of the Division of Industrial Research, State College of Washington, has been engaged in intensive research on the amenability of these low grade ores to froth flotation. The results: successful flotation of autinite, chief mineral constituent. At the outset of this work the goal was a concentrate of 1 pct U308 with a 90 pct recovery from ores containing less than 0.2 pct U3O8. Most of the work has been done on argillite ore from the Midnight mine on the Spokane Indian Reservation. The goal has not been attained using this ore, but samples of the granite ore from Mt. Spokane yielded successful results. For example, a concentrate containing 11.2 pct U308 was produced from a Mt. Spokane high grade ore containing 1.27 pct U3O8 with a recovery of 97.8 pct. Another Mt. Spokane ore yielded a concentrate of 5.0 pct U3O8 from an ore containing 0.13 pct U3O8, with a recovery of 85 pct. This same ore gave a recovery of 93.5 pct when the grade of concentrate was reduced to 2.0 pct.

Jan 1, 1959

By KENNETH W. GREENAWALT, William Greenawalt

THE patent system, through which an inventor is given exclusive right to his invention for a limited period as a reward for his industry and in reimbursement of his expenditures, originated in England in the famous "Statute of Monopolies," enacted in 1623. The first patent granted in America was to Samuel Winslow, in Massachusetts, in 1641. The basis of the patent system of the United States is a provision in the Constitution giving Congress the power to secure to inventors for a limited time the exclusive use of their discoveries. The first legislative enactment was the law of 1790, which was placed on the statute book after Washington had addressed Congress in its favor. Under this law, the Secretary of State, the Secretary of War, and the Attorney General constituted the board for the examination of patent applications and the granting of patents. The first Secretary of State, Thomas Jefferson, became the first administrator of the patent sys- tem in this country. He personally examined every application filed during his term of office.

Jan 1, 1930