Search Documents

By Henry Howe

1. Introduction.-This paper is based in large part on the examination of two rings, shown in section in Fig. 4 to 15, cut from an eroded 14-in. (35.56-cm.) gun, liner, and containing, according to Booth, Garrett, & Blair: Carbon, 0.380 per cent.; manganese, 0.655 per cent.; nickel, 2.810 per cent.; vanadium, 0; chromium, a few hundredths of 1 per cent.; tungsten, 0; molybdenum, 0. These rings were received from Admiral Joseph Strauss, then Chief of Ordnance, U. S. Navy, through the kindness of Mr. Hudson Maxim, Chairman of the Committee on Ordnance and Explosives,, of the U. S. Naval Consulting Board.

Jan 2, 1918

By W. E. Mitchell

The ore that is being treated by the present plant lies between the leached zone, or capping, and the mixed sulfide and oxide zone. The principal copper minerals are chalcanthite (CuS04.5H20), brochantite (CuSO4.3Cu (OH)2 and atacamite, (CuC12.3Cu (OH)2). There are, in addition, some other minerals such as cuprite and kröhnkite (CuS04. Na2S04.2H20). These minerals, with many others, occur in a greatly crushed granodiorite rock. most of the copper-bearing minerals occur in the cracks and veinlets, but there are disseminated values and it is probably the relative proportion of these that accounts for some otherwise unexplainable variations in extraction. The entire mineralization of the ore is complex and varies with depth. This variation, the problems presented thereby, and the effect of various constituents of the ore will be taken up in detail. An analysis of :in unweighted composite of the ore treated during 1927 follows: I'Lr Cent. Per Cent. Per Cent. Cu............... 1.58 S................. 2.10 Mo............ 0.01 SiO? ............. 66.10 HNO3 ........0.03 As............ 0.005 Fe.......... 1.41 C1 .............. 0.05 Sb............. 0.005 CnO ..... 0.20 Na................ 0.80 Ba............ 0.01 A1203 .......... 17.70 KI.............. 4.80 H20............ 0.70 mgO.............. 0.68 Mn............... 0.07 0 in sulfates. . . . 3.94 Total..... 100.19 The most important constituents of the ore, as indicated by experience to date, are: (1) The total copper content; (2) the acid-insoluble copper; (3) the acid-making copper mineral, mainly the chalcanthite; (4) the chlorine; (5) the nitrates; (6) the soluble iron; (7) the soluble molybdenum. The total copper content needs no discussion. In Table 1, the values are weighted averages calculated from individual charge analyses. The acid-insoluble copper directly affects the extraction, as the present leach recovers practically no acid-insoluble copper. In Table 1 the values are unweighted averages of the analyses of monthly composite samples. The acid-making copper mineral affects the amount of copper that can be dissolved from the ore without neutralizing acid in the solution. The

Jan 1, 1930

By Thomas R. Cunningham, A. B. Kinzel

Silicon, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have developed procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, arid the term "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.' In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve and further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treatment, he does not mention the existence of carbon in the alloy; nevertheless, he reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1940

By A. B. Kinzel, Thomas R. Cunningham

Silicon, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have developed procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, arid the term "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.' In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve and further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treatment, he does not mention the existence of carbon in the alloy; nevertheless, he reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1940

By Charles L. Harness

STRONTIUM is an essential constituent of celestite (strontium sulphate), of the rarer strontianite (strontium carbonate), and of a few very rare minerals. Celestite is the chief ore but strontianite is more valued except for making the purest strontium salts, because of its ease of processing. The public knows strontium mainly as the source of the red flame in fireworks but it has many other uses. PROPERTIES The celestite of commerce is a massive mineral of varying texture: coarsely crystalline, fibrous, bladed, very fine grained or earthy. The color varies greatly with the nature of the impurities but the purer specimens are light blue (Latin, caelum, sky) or white. The strontianite of commerce is a massive mineral, more or less coarsely crystalline. The color varies with the impurities. Distinctive characteristics are effervescence with acids, density (3.68 to 3.71), and crimson strontium flame. A typical British celestite before World War II analyzed: SrSO4, 96.55 pct; SrCO3, 0.17; BaSO4, 0.25; CaSO4, 0.54; MgCO3, 0.15; R20,, 0.90; Si02, 1.38.10 A German strontianite analyzed: SrCO3, 90.9 pct; CaCO3, 7.5; BaCO3, 0.1; Fe2O3, 0.05; A1203, 0.1; SiO2, 0.04; S, 0.1; P, 0.005.10 ORIGIN AND MODE OF OCCURRENCE According to Clarke,9 strontia forms about 0.02 pct of the crust of the earth and is present in most igneous rocks, but in smaller quantities than barium. Under certain conditions, large masses of celestite are deposited from sea water with anhydrite. The presence of large amounts of celestite in some saline deposits and its absence in others suggests that the deposition of celestite depends on whether certain as yet undetermined concentrations of sulphate and chloride ions are reached in the brines. The most extensive of these sedimentary deposits are those of the Keuper (Triassic) in England, of the Zechstein (Permian) in Germany, and of various Cretaceous formations in Texas, Arkansas, and Utah. Of the deposits of southeastern California and western Arizona,

Jan 1, 1949

By S. C. Carapella, E. A. Peretti

DURING a literature survey of the indium-zinc phase diagram, controversial reports on the composition of the eutectic point were encountered. The value reported in the investigation of Wilson and Perettil and in a later investigation by Valen-tiner' was 4.0 wt pct zinc. The most recent work recorded on this system consisted of an exhaustive survey of alloys by Rhines and Grobe8 in which they indicate a value of 2.8 wt pct zinc for the eutectic composition. To clarify this aspect of the diagram, a series of alloys were prepared by melting the respective constituents in a glass test tube under a covering of mineral oil and slowly cooling the melt in a furnace. The zinc used was Baker's C.P. and had the following analysis: insoluble in H2SO4—0.0l pct; pb—0.001 pct; Fe-—0.001 pct. The indium, which was supplied by the Indium Corporation of America, had a purity of 99.9'7 pet with the following impurities: Cu—0.002 pct; Pb—0.006 pct; Sn—0.01 pct; Zn—0.01 pct. The alloys were prepared for metal-lographic examination using a technique already reported' and a new value of 2.0 ± 0.1 wt pct zinc was observed. An alloy containing 2.00 wt pct zinc was also made by melting the constituents under a vacuum. In both of these methods of alloy preparation the losses can be kept extremely small. Again, the characteristic eutectic structure was obtained, assuring confidence in this value. The accompanying micrographs are presented in support of this point. Fig. la represents an alloy containing 4.00 wt pet zinc, and reveals excess zinc particles, which precludes the value of both Wilson and Peretti, and Valentiner. Fig. lb, gives the structure of an alloy containing 2.2 wt pct zinc, also showing the presence of excess zinc. Fig. lc is a micrograph of a typical structure of the eutectic observed in several sections of the 2.0 wt pct alloy. In the 1.8 pet zinc alloy, fig. id, the definite presence of the primary indium can be noted. From these re-

Jan 1, 1951

By WILLIAM WATERS

L HISTORY. THE Pierrefitte mines, situated in the South of France, in the district of the Hautes-Pyrenees, owe their name to the fact that the first mining operations of any extent, and of comparatively recent date, were carried out in the neighborhood of the vil¬lage of Pierrefitte, which is a branch terminus of the Midi railway. The Pierrefitte mines, however, embrace a wide extent of country and several different concessions, on most of which comparatively little exploration-work has been done. The portion of the property presently to be described is a zone running roughly E-W., over a distance of about 5 miles from the valley of Cauterets to the valley of Estaing, the ridge dividing these valleys being a spur of the main chain of the Pyrenees, and running more or less at right angles to it. According to local tradition, which various indications tend to confirm, these mines are of ancient date, the first workings being attributed to the Romans, who are supposed to have sought not only the lead but also the silver which is contained in the ore. Old slags have been found in the neighborhood which might well have been produced from the cupellation of lead-ores. These old workings, while of considerable extent at times, do not seem to have extended beyond a depth of 100 ft., even this depth being somewhat exceptional. The old notarial records of the district show that mines were known to exist, and that they were even worked, in the sixteenth century, but since the mines were abandoned (by the Romans or others) considerably prior to this period, very little

Nov 1, 1908

By C. M. White

CITIZENSHIP is a rather abstract subject on which a great deal could be said-a subject on which a great deal is said -and still one which too many of us seldom think about and seldom work at. Too many of us engineers and business men have but a vague idea of citizenship. We think that if we go to the polls on election day and obey the laws scrupulously, with the exception of an occasional traffic violation, we are pretty good citizens and are doing our duty by our city, state, and nation. But when you think it over, that's a very passive observance of the important right of counting oneself a citizen of a country. There is nothing very positive in that attitude. There is nothing that indicates that we have sufficient interest to really go out and do a job for the -welfare of our country, forgetting any personal advantages or inconveniences that might arise. In other words, this type of voting-on-election- day, law-abiding citizenship does not keep us awake a single minute; it does not take any particular thought or require the expenditure of any time or energy.

Jan 1, 1939

By N. B. Hoffman

Much of the drill steel produced in America is manufactured into hollow rods. After all forging has been finished the entire bar should be thoroughly annealed and heat treated before the point is hardened and tempered, at least where the drill has heavy duty, such as working in deep holes and hard rock. A large number of tools of like character and doing work requiring similar properties are now being made of alloy steels; for instance a steel with a carbon content of 0.75 to 0.85 per cent., manganese 0.25 to 0.35, phosphorus under 0.020, sulfur under 0.030 and vanadium 0.18 to 0.23 has proved very satisfactory for chisels. A steel of this type properly manufactured will be far superior to the ordinary carbon steels, while at the same time is one whose price range should not prove prohibitive. Much of the cutting efficiency of a drill depends on proper heat treatment. This vanadium steel has a far greater safe hardening and forging range than ordinary carbon steels, making it more nearly foolproof. It will harden nicely at 1400" I?. but will also harden well and satisfactorily at 1550" F. retaining its quality of hardness and toughness in either case.

Jan 1, 1922

[NOTE.-The names of authors of papers are printed in small capitals, and the titles of papers, in italics. Casual notices, giving but little information, are indicated by bracketed page numbers. Large Roman numerals are volume numbers; small Roman numerals after volume numbers following titles indicate the page on which the presentation of the paper is mentioned; Arabic figures refer to the text of the printed papers.] A Use Classification of Coal, (ASHLEY) LXII [xiv]; LXIII, 782; Discussion: (HALL), 794; (ZERN) , 795; (ASHLEY), 795 Absorbent material, liquid-oxygen explosives, LXXI, 1251. Absorbents for liquid-oxygen explosives, LXIX, 292, 299. Absorption : cupellation : gold, special cupels, LIX, 194. primary and secondary, LIX, 213. ratio of silver to gold, LIX, 212. silver, specla1 cupels, LIX, 195. Absorption method, gasoline from natural gas, LIX, 584, 585. Absorptzon of Sulfur from Producer Gas zn Open-hearth Furnaces (NEAD), LXX, 176; Discussion: ( WATERHOUSE), 184 ; (REYNDERS) , 184; (KINNEY), 184 Accelerated wearing tests, bearing metals, LXIX, 973. Accident prevention, results, Utah, LXVIII, 360 Accident Prevention, 1919 (SINN), LXIII, [xiii] Accidents: causes in coal mines, LXXI, 1229. classification, Anaconda Copper Mining Co., LXVIII, 9. coal mining: comparison with metal mining, LXVIII, 360. pillar mining, LXVIII, 323. relation to method, LXVIII, 323 shafts, LXVIII, 207, 209 Utah, LXVIII, 363 - concentrating mills, Utah, LXVIII, 362 liquid-oxygen explosives, LXIX, 330, 339 losses through, LVIII, 65 metal mining, LXVIII, 361, 363. mine: causes, LIX, 652. curve of decrease, LIX, 655 days of greatest frequency, LIX, 657 human element as cause, LIX, 652, 653. intemperance as cause, LIX, 658 labor relation, LIX, 652 prevention, LIX, 653. record, New Jersey Zinc Co., Franklin mine, LIX, 655 time of greatest frequency, LIX, 657, 658 Utah, LXVIII, 360 prevention, LVIII, 65 report blanks, Anaconda Copper Mining Co, LXVIII, 13, 15. statistical base, Anaconda Copper Mining Co, LXVIII, 9 time lost, LVIII, 70 transportation, Clifton-Morenci district, LXX, 851.

Jan 1, 1926

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

The results of a preliminary study of 113 ternary titanium-base alloys are described. The compositions investigated were as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships for these alloys were determined. THIS is the second in a series of papers describing some of the results of the exploratory work on titanium alloys being conducted at Battelle Memorial Institute for the Wright-Patterson Air Force Base. The work with the binary alloy systems has been described in a previous publication.' This paper describes ternary titanium-base alloys as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. As the preparation and fabrication of the 0.5-Ib experimental titanium alloy ingots to 14-ga sheet, as well as the methods of testing used in this work, have been described in the first paper of this series, Titanium Binary Alloys, no further discussion of these techniques will be given. Ternary Alloys Containing Carbon The following alloys of titanium, containing carbon and one other metal, were investigated: 1. 0.25 pct carbon; 1, 2.5, and 5 pct copper. 2. 0.25 pct carbon; 1, 2, and 3 pct silicon. 3. 0.25 pct carbon; 1, 2.5, and 5 pct vanadium. 4. 0.25 pct carbon; 2.5, 3.5, 5, 10, and 15 pct chromium. 5. 0.5 pct carbon; 2.5, 3.5, and 5 pct chromium. 6. 0.25 pct carbon; 1, 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 7. 0.5 pct carbon; 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 8. 0.25 pct carbon; 0.25, 0.5, 1, and 2 pct iron. 9. 0.25 pct carbon; 1, 2, and 3 pct cobalt.

Jan 1, 1951

By R. Dawson Hall

LONG regarded as nearly worked out, the anthracite region still shows promise of a hundred years of life, for means are being found to get bottom, top, pillar, and other coal that earlier generations disregarded as too expensive to mine. Rock drivages and, still more, machinery are making it possible to get such coal. Mechanical methods enable the owner of thin beds to mine these with profit, and the miner recognizes that he must permit the use of machinery or the inexorable laws of economics will deny him opportunity to work. E. L. Dana, Jr., well outlines this situation, which in the past year became definitely established. Stripping also is recovering, safely and inexpensively, coal that past generations regarded as too hazardous and costly for mining.

Jan 1, 1935

By Hugh P. Nicholson

IN view of the many articles that have been written on the proper classification of mining systems without so far having produced any particular tangible results it might seem that the subject is hopeless of solution. I do not believe that is so, and my intention in contributing the following outline is to present a slightly different viewpoint. Too much attention is often focused on unnecessary details and not enough on general principles. Too much attention and emphasis is often given to the system employed at one particular mine or in one particular district. In addition, names that are entirely misleading are applied to mining systems, and their adoption by the coming generation perpetuates a condition that needs clarification badly. The following classification is the result of several years of practical experience in mining and also several years' practice in teaching the same subject. It therefore represents a broad picture of the entire field of mining systems from the viewpoint of the miner as well as the teacher. It seems that the difficulty in the past has been in reconciling these two viewpoints. The need of such a reconciliation requires no explanation.

Jan 1, 1934

By W. B. Triplett, H. I. Aaronson, G. M. Andes

THE morphology and mechanism of the proeutectoid a and the eutectoid reactions have been recently investigated in some detail in an iodide-base Ti—7.22 pct Cr alloy.' These studies have now been extended to an iodide-base Ti—10.8 pct Cr alloy in order to evaluate the effects of composition on the proeutectoid and eutectoid transformations in titanium-chromium alloys. The alloy used in this investigation had the following composition: 10.8 Cr, 0.0327 0, 0.011 N, 0.0063 H, and 0.011 pct C. Specimens of this alloy were heat treated in evacuated and internally get-tered Vycor capsules. The specimens were solu-

Jan 1, 1959

By Carlo Massa

THE Societá Auonima di Miniere e di Alti Fourni, familiarly known as the " Elba Company," works the rich ore-deposits of the Island of Elba under a long-term contract with the Italian Government. The ore-deposits are scattered over the eastern and southeastern coast; but as those parts of the island are not well provided with ports, the blast-furnaces were built at Portoferraio, the principal town of the island, situated on the northern shore, and possessing a magnificent natural harbor where even vessels as large as the battleships of the Italian navy can comfortably anchor. In the selection of Portoferraio. the cost of transporting the iron-ore from the different mines to the blast-furnaces has been reduced to a minimum, and shelter has been provided for the Company's flotilla of tugs and barges, as well as for the steamers carrying coal and pig-iron. The whole plant, of which a general view is given in Fig. 1, comprises 1. A discharging-pier with unloading-cranes. The ore and coal are transported from this pier by means of an aerial cable-rail¬way to the coal- and ore-storage yards. This cable-railway is supported by an iron bridge extending from the pier to the shore and by a wooden trestle extending from the shore to the yards. , 2. Blast furnaces, two in number, with all the accessory appa¬ratus, such as blowing-engines, dry purifiers, Cowper hot-blast stoves, hoists, etc. 3. Coke-ovens, two batteries, with coal-bin, crushers and boilers. 4. Engine-house containing the blast-engines and the electric generating-station. 5. Pumping-plant. 6. Narrow-gauge railways.

Mar 1, 1905

By Albert J. Phillips

FOR the most part, recent changes in nonferrous physical metallurgy have been gradual and of a transition nature rather than abrupt modifications of existing methods. Development of new alloys containing vital constituents in what formerly would have been considered minute amounts has necessitated more precise control of metallurgical procedure than ever before. Realization of the remarkable effects of minute amounts of specific foreign elements in many alloys has brought about a revolutionary control in the selection of even the most commonplace raw materials. In addition, recognition of the widespread occurrence of precipitation hardness in metal systems, and the utilization of many of these, has emphasized not only the need for precise temperature control but also the necessity for considering the time factor in its effect upon properties in the treatment of most metals. These needs have caused the development and widespread installation of equipment that permits precision of control undreamed of a generation ago.

Jan 1, 1935

By H. C. Fiedler

Heats of high purity iron containing 3.1 pct Si and be -tween 0.0003 and 0.0295 pct N were prepared by vacuum melting ad then pouring while in a nitrogen atmosphere with the pressure between 0 and 90 psi. Strip from a heat with 0.0184 pct N underwent complete secondary recrystallization during the final anneal. Heats with less nitrogen had too few Si3N4 particles to restrain normal grain growth, and the heat with higher nitrogen had too many particles to allow complete secondary recrystallization. In the hot-rolled structure, Si3N4 precipitates only at the grain boundaries, with the consequence that annealing after hot-rolling diminishes the ability to subsequently undergo secondary recrystallization. In contrast to this behavior, ALNprecipitates uniformly in the hot-rolled structure. Under 1 atm of nitrogen, Si3N, in 3.1 pct Si-Fe dissociates between 900" and 950°C; the solubility of nitrogen increases from 0.0010 pct at 900" to 0.0030 pct at 1200°C. The solubility of nitrogen in Si-Fe has been the subject of many investigations. Corney and Turkdogan1 heated a 2.83 pct Si alloy in nitrogen and found the solubility, under 1 atrn of nitrogen, to be 0.0019 pct at 900°C. They claimed that Si3N4 did not form in the alloy above 705°C in 1 atrn of nitrogen. Fryxell et al.2 heated samples of 3.25 pct Si-Fe containing 0.0025 pct N over a range of temperatures and then analyzed for total nitrogen by vacuum fusion and for nitrogen in solution by a modified Kjeldahl technique. At 900°C, they reported the solubility of nitrogen in equilibrium with Si3N4 to be 0.0011 pct. pearce9 found the solubility of nitrogen at 900°C under 0.95 atrn of nitrogen to be 0.0017 pct in a 3.06 pct Si alloy. He reported that Si3N4 does not form above 770°C in 1 atrn of nitrogen. Although internal friction measurements have given somewhat higher values for the solubility,4-6 if the solubility of nitrogen is as low as has been reported by most investigators, and if Si3N4 is stable up to at least 945°C at 1 atrn pressure of nitrogen as reported by Seybolt,7 a small amount of nitrogen in properly processed Si-Fe should be effective in promoting secondary recrystallization. The requirement is that in the final heat treatment there be enough small, well-dispersed particles of Si3N4 to restrain normal grain growth. Fast8 has obtained secondary recrystallization by nitriding high-purity 3 pct Si-Fe after hot-rolling to a thickness of 0.118 in., followed by processing to 0.012 in., and annealing. A large amount of nitrogen, 0.076 pct. was introduced during the nitriding heat treatment, but he has since reported9 that "a few hundredths of a percent" is sufficient. Small amounts of aluminum10 or vanadium" nitride are capable of promoting secondary recrystallization. Heats containing as little as 0.010 pct A1 or 0.042 pct V and from 0.006 to 0.009 pct N underwent complete secondary recrystallization at final gage, whereas heats with lesser amounts of aluminum or vanadium did not.l2 To be reported is the behavior of nitrogen in high-purity 3.1 pct Si-Fe, and the relation of this behavior to the ability to undergo secondary recrystallization. PROCEDURE Ingots weighing 1 lb were made by vacuum melting high-purity electrolytic iron (A104, Glidden Co.) and high-purity silicon (Monsanto Co.). The latter was used in preference to ferrosilicon to insure a low aluminum content. The design of the melting furnace permitted pouring with the furnace atmosphere either below or above atmospheric pressure. Accordingly, at the completion of melting, nitrogen was admitted to the desired pressure and the heat then immediately poured. The ingots were sound, with no indication of porosity. In Table I are listed the heats investigated, the nitrogen pressure at pour, and the nitrogen and oxygen contents as determined by vacuum fusion with a platinum bath at 1850°C, a procedure which insures measurement of the total nitrogen.13 In addition, all heats contained 3.1 pct Si and not more than 0.002 pct C, 0.003 pct S or 0.005 pct Al. It was subsequently found that the quantity of nitrogen contained in the heats in Table I does not necessarily represent that obtained under equilibrium conditions. For example, the ingot poured immediately after 1 atrn of nitrogen was admitted to the chamber contained 0.0093 pct N, whereas an ingot poured 3 min after the nitrogen was admitted contained 0.021 pct N and another poured after a 6-min delay contained 0.029 pct N. While some bleeding of the hot top occurred in the latter instance, the ingot when examined in cross section appeared sound. The ingots were heated to 1325°C in hydrogen and rapidly rolled to 0.080 in. in 3 passes. The roll speed of the final pass was reduced so as to increase the quenching effect of the rolls. The hot-rolled pieces were processed both as-hot-rolled and after heating for 3 min at 900°C in hydrogen. After cold-rolling to 0.026 in., the strips were heated for 2 min at 900°C in hydrogen, then cold-rolled to the final gage of 0.012 in. The loss of nitrogen in going from the ingot to cold-rolled strip was no more than 10 pct. The final heat treatment, which was for the purpose of develop-

Jan 1, 1970

By E. S. Machlin, Morris Cohen

The martensite reaction in single crystals and polycrystals of 70 pct Fe-30 pct Ni alloys is shown to be autocatalytic in nature, producing bursts of transformation during cooling. The temperature of the first burst of transformation, called Mb, occurs below M, in these alloys. Experiments were devised to test the athermal embryo and strain embryo theories of martensite nucleation. The results indicate that internal strains, either within the virgin austenite or around existing martensitic plates, control the nucleation process in these alloys. Furthermore, the growth of martensitic plates is not limited by the attainment of an elastic balance with the austenitic matrix, but by the occurrence of plastic deformation at the martensite boundaries which interferes with the propagation mechanism. IN an investigation of the martensitic habit in single crystals of a 69 pct Fe-31 pct Ni alloy,' it was observed that about 25 pct of the austenite transformed during subatmospheric cooling within the time-interval of an audible click. This event proved quite spectacular: The shock wave sent out from the specimen freely suspended on a thread in the refrigerating liquid was occasionally sufficiently intense to shatter the Dewar container and to separate the toluene column in the immersed thermometer. The Present investigation was undertaken to determine- the kinetics and mechanism of this "burst" type of martensitic reaction. The analyses of the alloys studied are given in Table I. The composition of the single crystal specimens is designated by alloy A, while the polycrystal-line specimens were made of alloys B and C as noted in the text. The single crystals were prepared in a vacuum furnace, using a modified Bridgman technique. Most of these crystals were homogenized by holding for 24 hr at about 1300°C just after solidification. However, it may be emphasized here that the degree of homogenization was not a controlling factor in the subsequent experiments, inasmuch as specimens having different degrees of homogenization yielded the same results. All of the single crystals were fully austenitic as slowly cooled to room temperature. An illustration of the burst phenomenon is given in Fig. 1, which shows oscillograms of electrical resistivity and temperature vs. time during the continuous quenching of 1/16 in. wire specimens (alloy B) in a dry ice and acetone bath at —77°C. There are at least two observable bursts in this case, as indicated by the sharp decreases of resistance accompanying the sudden formation of substantial quantities of martensite. The thermal arrest during the quench probably corresponds to the larger burst. Usually the bursts are followed by more or less progressive transformation during continuous cooling. It will also be noted that the resistance continues to decrease after the specimen has reached the bath temperature. This isothermal change denotes the formation of martensite at constant temperature, and will be the subject of another paper. Examination of fiducial scratches on the surface of a transformed single crystal has shown2 that the scratches in adjoining nonparallel martensitic plates are usually bent in opposite directions, as though one plate forms in such a way as to relieve the matrix stresses set up by the adjacent plate. This, together with some of the results described in ref. 1, Table I. Compositions of Alloys Studied, in Percent Alloy Ni C N Mn Si P S Cr A 31±0.3 0.048 0.027 0.003 0.56 0.007 0.002 B 29.5±0.2 0.036 0.02 0.19 0.09 0.008 0.006 C 19.99 0.52 0.37 0.47 0.010 0.015 0.04 led to the tentative concept that a cooperative action exists which provides the impetus for much of the transformation that appears during the burst. The following series of experiments were performed in order to test this idea. Cooperative Nature of the Burst Two adjacent disks, Va in. thick x % in. diam, were cut from a single austenite crystal of alloy A using a jeweler's saw. One of the disks was then cut into 15 parts. Then 12 of the latter pieces and the second disk were austenitized (stress relieved) at 600°C for 30 min and water quenched to room temperature. The temperatures at which the first burst of transformation appeared were determined for

Jan 1, 1952

By D. W. Lillie

Property changes produced by irradiation of Al-0.4 wt pet Li alloys at 270°C to a burnup of 0.155 pct of all atoms are described. Metallographic evidence of the formation of internal pores and the concentration of gases at grain boundaries is shown. Some conclusions are drawn concerning desirable property characteristics for resistance to radiation swelling. RADIATION induced gases are of great practical significance in nuclear engineering since they affect the behavior of fissionable fuels and control rod materials. In fuels the gases xenon and krypton are the major offenders, producing serious em-brittlement at low irradiation temperatures and gross swelling at high irradiation temperatures. In control rod materials containing boron, the production of helium from the B 10 (n, 0) Li7 reaction produces similar reactions. Since the trend in reactor design is for operation at increasingly high temperatures, the phenomenon of high-temperature swelling by these induced gases has been the subject of considerable recent study. The objectives of such work have been to obtain engineering information and quantitative data on the effects in specific fuels and control rods and to obtain further understanding of the mechanism of gas damage so that more intelligent corrective steps can be made. Analogue systems are often useful for the latter objective and in this case alloys containing Li are suitable in view of the reaction Li6 + n - He4 + He 4. Both products are gases and no serious radiation problem is produced to complicate post irradiation handling. Considerable caution is, of course, necessary in any operations in which tritium release is possible. The present program was initiated to provide a detailed study of the effects of He + H3 generated by irradiation in Li-bearing alloys. The results on Mg-Li solid solution alloys have been reported elsewhere.' This paper presents information on irradiation of an A1-0.4 pct Li alloy in which the lithium was present as highly enriched Li6 in order to maximize the radiation burnup. PROCEDURE The original intent in the selection of the alloy content was to have Li in solid solution at all temperatures. It became apparent, however, that the solubility of Li in A1 was substantially lower than that reported in the original reference consulted.' This was substantiated by the work of Nowak3 who reported solubility of less than 0.01 pct Li at 100°C. The alloy used (0.4 pct Li) was therefore two phase at room temperature. The irradiation temperature was estimated to be about 270° C, and at that temperature all or almost all of the Li would be soluble under equilibrium conditions. The precise state of the alloy under irradiation is not known. Aluminum used was 99.996 pct purity (max. impurities Si 0.002 pct, Mg 0.001 pct, Fe 0.0005 pct, and Cu 0.0005 pct). The lithium was obtained from Oak Ridge National Laboratory; 96.1 + 0.1 pct of the lithium was ~i~, but chemical impurities were 0.25 pct Ca, 0.05 pct Fe, 0.02 pct Na, 0.02 pct Cu, 0.01 pct Sr, and 0.01 pct Ba. The two metals were melted in an alumina crucible in a resistance heated furnace in an atmosphere of helium. A l-in. ingot was cast in an iron mold, machined to %-in. round, hot swaged (350°C) to 0.080-in. round, cold swaged to 0.060-in. round, and finally cold drawn to 0.040-in. round. Four-inch wire lengths were then cut and annealed at 250°C for 4 hr in helium. Irradiations were carried out in a VT hole in the Argonne CP-5 reactor. The wires were held in an aluminum jig, sixteen wires per capsule, and were maintained in a helium atmosphere for maximum heat transfer. Eight wires of pure aluminum and eight of Al-Li alloy were placed in each capsule. Argome Laboratory statements were accepted as establishing flux and exposure levels. These were based on previous experience and flux map-

Jan 1, 1961

By AIME AIME

Russell B. Paul, Chairman of the Special Committee on Divisional Relationships, presented the interim report of his Committee which was published in the September, 1945, issue of MINING AND METALLURGY and a copy of which is incorporated in the official minutes of this meeting. The following specific actions were taken by the Board of Directors in relation to the six recommendations in the Summary of the Report as published: (1) Mr. Haider, Chairman of the Petroleum Division, presented the formal request of his Executive Committee that the headquarters of the new Secretary of the Petroleum Division be established in Dallas, Texas. After lengthy discussion in which the point was made that the success of this program would depend upon effective co-operation between the Chairman of the Division, the Secretary of the Petroleum Division, and the Secretary of the Institute, the request was approved. The new secretary will be selected by the Division and will be employed by the Institute in the capacity of an Assistant Secretary. (2) The following item in the report was approved:

Jan 1, 1945