Search Documents

By Nicholas J. Grant, Yoichi Ishida, Arthur W. Mullendore

An inert particle -marker technique was developed to provide a direct measurement of grain boundary sliding during creep in tile interior of aluminum specimens. Groin boundary sliding in the interior as measured by this technique was found to be nearly the same or slightly lower than that measured on the surface. These data disagree with those obtained by the grain-counting technique developed by W. A. Rachinger. In tests where both techniques were used, the grain-counting technique gave large and variable values of grain boundary sliding. It is shown that the grain-counting technique gines erroneozcs results because of a preferred direction of grain growth during creep. A question which has long plagued those who study grain boundary creep is whether or not surface measurements yield a true representation of the deformation in the interior of a specimen. The first attempt to measure grain boundary sliding in the interior of a creep specimen was made by Rachinger.1 His technique is based on the measurement of average grain diameters, both parallel and perpendicular to the tension axis, followed by a calculation of the grain elongation from these measurements. The difference between total elongation, Et, and the calculated grain elongation, Eg, is considered to be the result of grain boundary sliding, Egb. Surprisingly large values of Egb/ Et (90 pct) came out of creep tests of pure aluminum at temperatures above 250°C (480°F), utilizing the Rachinger technique. This value is very much larger than the values of 8 to 15 pct measured by numerous investigators on the surface of a specimen. Values obtained on the surface by Rachinger, however, were consistent with those measured by the displacement of reference scratches. Chaudhuri and Grant2 repeated the Rachinger method for A1-10 pct Zn, and found the same large values of Egb/Et inside the specimen. However, from purely geometrical considerations, grain boundaries cannot slide without grain deformation; therefore, they questioned the validity of Rachinger's grain-counting method. Several authors2,3 have suggested that grain boundary migration during high-temperature deforma- tion may tend to restore the equiaxed grain shape in order to minimize interfacial energy. Rachinger4 tested this hypothesis and found that it did not hold. Grains elongated by rapid extension retained their elongated shape during a subsequent slow creep test. It appears that some other factor was responsible for the abnormally high values of .Egb/El. McLean and Gifkins5 made a survey of the effect of grain size on the ratio Egb/ Et, and proposed that the high values were the consequence of a small grain size. They failed to explain the low value of Egb/Et which Rachinger observed on the surface of the small grain size specimens, and suggested that the surface effect on the value of Egb/Et does not always occur. Many of the disagreements arising from Rachinger' s work stem from the fact that there was only one method of estimating grain boundary sliding in the interior of a specimen, and that method was of an indirect nature. If a marker line of some sort could be introduced inside of the specimen, one could make measurements just as clearly as on the surface. In the present investigation, the technique utilizes a layer of finely dispersed oxide particles inside the specimen introduced by hot press-bonding of two pieces of aluminum. Rachinger attempted a similar technique but with the oxide distribution he obtained there was so much interference with grain boundary motion that quantitative measurements were not attempted. MATERIALS AND EXPERIMENTAL PROCEDURE A) Materials Preparation. Two pure aluminum rods (impurity content in percent: Si, 0.002; Cu, 0.004; Fe, 0.002; Mg, 0.000: Zn, 0.000; V. 0.001) 1 in. diameter by 2 in. high were jacketed end to end in a 4-in.-diam cylinder of commercial-purity aluminum, 4 in, high, which had a l-in.-diam hole. The l-in.-diam mating surfaces of the two pure aluminum rods had been electropolished initially. This interface provided the oxide-film internal -marker plane after the hot press-bonding process, see Fig. 2. The composite was annealed for 1 hr at 900 F and hot upset more than 50 pct reduction in height in one step. The resulting slab was then rolled to 1/2 in. thickness; the pure aluminum test material was cut out and annealed at 900°F for 1 hr and cold cross-rolled to 1/8 in. thickness. The sheet was machined into specimens with a 1/8-in.-square cross section and a 1/2-in. gage length. The following heat treatment was given the specimens: Specimen 5A series: annealed at 1000°F for 5 min for grain-size control and then cooled to 700°F and held for 15 hr for stabilization.

Jan 1, 1965

By K. Stout, E. Van Eeckhout, L. Friel

Previous research at the Montana College of Mineral Science and Technology indicated that it is practical and economically feasible to place stiff back- fill in a cut-and-fill stope. This backfill would reduce wall closure and high stress buildup in pi1llars, thus alleviating rockburst potential. Three ;topes from the Sunshine Mine, of the Coeur d’Alene Mining District, were chosen for a test verification of this concept. Although the first stope was lever mined beyond the initial cut (for economic reasons), some vibrating wire stressmeter results were obtained and found to compare favorably with numerical predictions. Some other instrumentation devices were built and tested, but never installed .

Jan 1, 1984

By Thys B. Johnson

Traditional mine planning concepts are discussed and suggestions for improvement through use of the developed model are proposed. The approach developed in this paper allows optimal planning of the complete mining-concentrating-refining system over the entire planning horizon and permits the system to dictate how and when to process a block of material, i. e., a dynamic cutoff.

Jan 1, 1969

By Barry K. McMahon

Following minor slope failures at the commencement of mining the west wall of the Kanmantoo Mine was redesigned from an overall slope between haul roads of 55° to 46°. This decision was based on a probabilistic analysis which indicated that 46° was the optimum economic slope.

Jan 1, 1983

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack.

Jan 1, 1949

By H. D. Wilde

GREAT emphasis is being placed today on petroleum as a source of chemicals. Such prominence is well merited, for rapid strides have been made in developing processes for the conversion of petroleum into synthetic chemical products, which are now being made on a huge scale. These marvelous accomplishments have resulted in some highly optimistic predictions as to what can be expected in the future. Many of these forecasts are well justified, but some writers, especially those contributing to the Sunday supplements and the popular-cience type of publications, have let their imagination run wild and present a rather distorted picture of the possibilities in this field in the postwar period. Commercial manufacture of synthetic organic chemicals had its beginning in England with the establishment of a plant by Sir William Perkin in 1857 for the manufacture of "Aniline Purple" or "Mauve." The preceding year he had discovered in the laboratory how this dyestuff could be made from aniline, one of the many derivatives of coal tar, and he soon made commercial application of his discovery. Influenced largely by his success, organic chemists began research on production of a vast array of synthetic dyestuffs, medicinals, flavors, scents, and explosives. Rapid progress was made and by the turn of the century hundreds of these products were being manufactured. Most of these synthetic chemicals were derived from materials obtained as by-products in the conversion of coal into coke. These by-products are generally referred to as "aromatics" and are obtained by processing coal tar recovered in the coking process, so they are popularly known as "coal-tar chemicals." During the early years of this century, coal-tar chemistry was the wonder of the age, and rightfully so, since the products so made seemed limitless.

Jan 1, 1944

By Mungo Park, C. Baring Horwood

This paper is intended, in the light of recent investigations, to call attention to some of the essential features of good practice in sampling and mine-valuation. Mine-sampling may be divided broadly into two classes: (1) development-sampling and cornputatioll of ore-reserves; and, (2) stope-sampling and estimation of stope-values. Development-Sampling. It is with development-sampling only that this paper deals— the term development being taken to mean the opening-up of a mine by cross-cuts, drives, connections, etc., preparatory to actual extraction of the ore for milling. In development-sampling the work of the sampler and the consequent estima-

Jan 1, 1909

Jan 1, 1893

By A. C. Butterworth

M OST operators of open-pit mines in the Lake Superior iron ore district are quite familiar with the use of fuel oil in the heavy-duty Diesel engines commonly used in truck-haulage service but some operators, including my own company, Pickands Mather, have had butane-engine trucks in service for several years, and less is known of their operation. One of the first installations of trucks for iron-ore haulage was in 1939 at a deep open-pit mine on the Cuyuna Range. These superseded standard-gauge steam haulage. Trucks then obtainable were equipped with 150-hp Diesel engines, and the speed of these units on an 8 % grade would have been so slow, considering the depth of the pit, that plans for an all-truck haul out of the pit were rejected. About this time one of the engine manufacturers brought out an auto-

Jan 1, 1948

By GEORGE O. SUMAN

IN THE operation of oil properties there are various difficulties with pumping wells which can often be overcome or greatly lessened if sufficient attention is, directed towards pump and tubing problems. The difficulties referred to are the wearing out of pumps, sanding up of pumps, and the sanding up of the hole. As the perforations in the oil strings are large and the oil and sand loose and unconsolidated considerable trouble is often encountered in pumping wells due to the ease with which' the sand can come into the holes. DETERMINING FLUID LEVEL In determining the proper depth at which to tube a well it is essential to first find out something about the behavior of the fluid in 'the hole: Facts in regard to this natter can be obtained by finding the fluid level on pulling the tubing, by making a pumping test on the well tubed to various depths, and by bailing tests during cleaning out work. In ordinary oil field operations it is customary to take the fluid level at the time of pulling the tubing. This 'can only be done when the pump is not sanded up. There are two methods used in obtaining the fluid level. One method is to note where the outside of the tubing starts, to be covered with fluid when pulling the

Jan 1, 1925

By J. A. Herbst, R. Mackelprang, J. D. Miller

Droplet size distributions were determined by stabilizing in gelatin and measurement of the distributions by means of computerized image analysis Several variables that affect droplet sizes were studied and the resulting size distributions were modeled via a population balance equation Key parameters in the model were related to the physical properties and operating conditions of the systems examined using a multiple linear approach

Jan 1, 1981

By J. J. Kramer, G. W. Wiener, K. Foster

The effects of the primary grain size and sheet thickness on the secondary growth rates of grains with (100) surface planes were studied in 3 pct Si-Fe sheets. This secondary grain growth was carried out under conditions in which the {100} plane had the lowest surface free energy. The value of the surface energy difference, between the (100) plane and the random matrix planes was found to he only about 3 pct of the grain boundary energy, indicating that most of the driving force for secondary growth is supplzed by grain boundary energy. A method for obtaining cube texture in 3 pct Si-Fe sheets by a secondary recrystallization process has been reported.' It has been demonstrated that a difference in surface free energy between the (100) plane and other planes is responsible for this growth, where the (100) plane has the lowest surface energy. A semiquantitative relation has been derived for secondary grain growth in sheets where primary grain growth has proceeded until the grains have grown through the sheet and the average grain diameter in the plane of the sheet is from one to two times the sheet thickness. Then, the linear growth rate, G, for the secondary grains can be given by where M is the grain boundary mobility, is the grain boundary free energy, is the average primary grain radius, A is the average difference in surface free energy between the (100) plane and planes of other orientations, t is the sheet thickness, and C is a term first proposed by zener6 which acts as a negative driving force, the effect of inclusions in holding up grain boundary motion. Since the problem of grain growth being discussed is under conditions where the matrix grain size is at least equal to the sheet thickness, the radius r is, of course, a function of the sheet thickness. The term B/r is the grain boundary driving force normally associated with inclusion inhibited or texture inhibited secondary recrystallization. Here, however, the term is modified to account for the fact that growth occurs in thin sheets. The term is the additional driving force available because of the difference in surface free energy. The purpose of the present work has been to evaluate the driving force terms of the growth equation by studying growth rates of (100) secondary grains as a function of sheet thickness and primary grain size. From these data it has been possible to determine the relative values of grain boundary energy, surface energy difference, and the inclusion term, C. EXPERIMENTAL PROCEDURE A 3 pct Si-Fe alloy was melted and cast under a helium atmosphere using electrolytic iron and a pure commercial grade of silicon as raw materials. The alloy was hot and cold rolled to a thickness of 0.6 mm, and samples approximately 5 in. long by 1 1/4 in. wide were cut from the cold-rolled sheets. Four different primary grain sizes were obtained

Jan 1, 1963

By R. W. Gurry

WHEN a steel in the austenitic state, with all its carbon in solution, is maintained, at constant temperature, in contact with a gas that removes the carbon from the surface, vet without otherwise altering the composition of the steel, the change in weight of the specimen, after any period of exposure, is a direct measure of the amount of carbon it has then lost. The purpose of the present paper is to show how, by application of established mathematical reasoning based on the fundamental diffusion law and on certain postulates, this loss of weight yields a complete picture of the distribution of carbon throughout a specimen of regular shape after any period of exposure, with all the accuracy required in any practical occurrence of decarburization. Precisely the same is true for the gain in weight during the reverse process of carburization, or for the gradual gain or loss of any element, so long as the steel comprises only a single phase at temperature, provided always that the experimental conditions conform to the postulates. The change in carbon content from surface to center of the specimen is always continuous, when everything is in solution, even though under the microscope the decarburized zone (or carburized rim) may appear to be sharply defined. The experimental procedure is described and some typical results are presented, which are then interpreted by application of the diffusion law. EXPERIMENTAL PROCEDURE Initially an endeavor was made to follow the gain of weight during the process of carburization in a hydrogen-toluene atmosphere, but it was soon found that the specimen became coated with graphite, which could not be removed without some loss of metal; therefore it was decided to continue carburization until the steel was saturated throughout, to remove all graphite from the surface of the specimen, and then to follow the loss of weight during decarburization in a moist hydrogen atmosphere at the same temperature as that used for carburizing. The carburizing procedure has been described in an earlier paper;1 it suffices to state here that the carburization lasted about 140 hr. at 760°C. (1760°F.) and 44 hr. at 1110°C. (2030°F.), these periods being long enough-on the basis of the calculations presented later-to ensure that the specimen was about 9.99 per cent saturated at each temperature. The speci¬men was a cylinder about 3.8 cm. long and 0.475 cm. in diameter; the materials were carbonyl iron, a commercial low-metalloid iron, and a steel with 3.6 per cent nickel and the usual proportion of other elements. The fully [carburized] specimen, after cooling at the top of the furnace tube, was placed in a lathe and sandpapered to remove all graphite; then the diameter was measured with a micrometer caliper, and the initial weighing (corresponding to complete saturation) was made. By means of a

Jan 1, 1942

By Axel Sahlin

Having no business interest in any of the various machines used for granulating ores, my remarks on the subject are prompted solely by my desire to contribute towards the determination of the best apparatus such information, as I have been able to gather,

Jan 1, 1893

By Lord Marley

ACTIVE participation by the United States in the war acted as a stimulant on the Annual Institute Meeting in New York rather than a retardant as feared. Attendance was about 10 per cent under the all-time high reached last year, but considering the number of men who could not possibly come because of active military service and the additional number who are devoting their whole time and effort to turning out vital war materials, the registration was really greater than might have been expected. But all in all the Institute put on a show that taxed the capacity of the Engineering Societies Building as well as the capacity of the visitors to find time to attend everything that promised to be of interest.

Jan 1, 1942

Jan 1, 1930

By Philip D. Shelton

INTRODUCTION Traditional design of support for permanent underground mine excavations place great emphasis on the magnitude of the maximum radial load which a specific support or lining must sustain. However, this depends upon so many factors that reliable prediction in advance of excavation is very difficult except in strong-self supporting ground. Some of the factors affecting the loads acting on a support are illustrated in Table 1. [ ]

Jan 1, 1984

By A. S. Malicsi, I. Iwasaki

Differential flotation of bulk sulfide concentrates from Duluth gabbro into copper and nickel concentrates could be implemented by first destroying the hydrophobic coating with ozone and then by recovering the copper concentrate with a copper-selective collector. A number of parameters involved in the use of ozone, such as the sequence and the conditioning time of ozone treatment, the pulp pH, and the level of xanthate addition, were investigated.

Jan 1, 1986

By J. A. Roberson, Robert A. Rapp

From the observation of platinum wire marker movement in the oxidation of columbium at high lemperatures and low oxygen pressures, predonzinant cation diffusion in CbO, has been demonstrated. The Cu,0 molecule was used as an oxidizing species to study the nature of the porous scale and the location of the reduction site in the oxidation of colum-bium. The Cb205 scale contains microporosity and forms by alternate ionic diffusional growth and fracture. The oxidation of columbium at high temperatures and very low po, results in a relatively compact and protective Cb205 layer. THE observation of marker movements during oxidation is one means for the identification of the mobile ionic species in an oxide lattice. Previous marker experiments in the oxidation of columbium have all resulted in the markers being found on the outside surface of the Cbz05 scale. The Cr203 powder markers of Klopp et a1.,' the gold film marker of Kofstad and ~jijllesdal,' and the platinum wire marker of Cathcart et a1 .3 were found at the oxide/gas interface for oxidation temperatures ranging from 450" to 120O0C. However, in all experiments relatively high oxygen pressures were used. As discussed by Mrowec, even the interpretation of marker experiments in simple scales containing only one compound is not without ambiguities. In brief, it can be said that a marker may be found almost anywhere in the scale layer if the metal oxidizes by cation diffusion through the scale; the position of the marker depends upon morphological happenings in the scale. When considering marker movement in a polyphase scale one must proceed with extreme caution. For example, in the past (and present) work markers have never been found at the columbium-scale interface, and one might infer that the oxygen ion is mobile in CbO and CbO,. However, only trace quantities of CbO and CbOz have been present on any of the specimens, so no firm statement is justified on this basis. Despite previous experimental work, considerable doubt still exists concerning the role of the oxides CbO and CbOz in the oxidation of columbium. The identification of the mobile ionic species in CbO and CbOz from the observation of platinum wire markers was one goal of the present investigation . The linear kinetics of columbium oxidation at high temperatures (T - 1000°C) suggests that the Cbz05 scales which form on columbium are porous. From mercury absorption measurements on a Cbz05 scale formed at 500"C, Aylmore et al.' reported a minimum volume fraction of connected voids equal to 0.15. While these scales often appear to be quite porous when viewed in metallographic cross section, they are so brittle that metallographic preparation is likely to exaggerate any porosity originally present. In this investigation, porosity developed during the oxidation of pure columbium and present at the high temperature was detected by oxidizing specimens in sealed evacuated capsules containing large compacts of mixed copper and CuzO powders. wooda has demonstrated that the CuzO, or (CuzO),, molecule is volatile and that oxygen is transferred by the CuzO molecule from a Cu/CuzO mixture to materials having a greater affinity for oxygen. For each molecule of CuzO that is reduced at a sink for oxygen, two atoms of copper are deposited. Quantitatively, essentially all of the oxidation carried out by a Cu-Cu20 compact results from a displacement reaction involving the CuzO molecule. When a metal which oxidizes to form a porous scale is exposed to the CuzO vapor, the CUZO molecules are reduced in the pores leaving a deposit of metallic copper to mark the site of the reduction. This technique has the rather unique advantage that any copper-coated pores found in the scale are unambiguously related to the reduction site in the growth of the scale under consideration. Pores or cracks which form in a msition*- external to the reduction site or which occur as a result of cooling or handling of the specimen will not exhibit the copper deposit. EXPERIMENTAL PROCEDURE Marker experiments were made on columbium metal, and on pellets of CbO which had been pressed and sintered. Platinum wire markers (0.001 and

Jan 1, 1968

By J. F. Tavernelli, L. F. Coffin

The deformation and fracture characteristics of eight metals subjected to fully reversed cyclic strain ranging from 0.2 to 50 pct were investigated at room temperature. Strain-hardening characteristics unique to the interna1 structure of a particular metal were found. Complete removal of the strain-hardening effects resulting from prior deformation was brought about by subsequent cyclic strain. Further support for the validity of the inverse relationship between the plastic strain range and the square root of the number of cycles for failure is given. THE resistance of materials to cyclic plastic strain is of interest both from a fundamental and practical point of view. It is now a well-accepted fact that fatigue failure in metals is a consequence of the localized slip deformation which occurs within the individual crystals of metal.'-' Hence the failure process should be strongly dependent upon the magnitude of the gross cyclic plastic deformation of the metal under conditions where this is a measurable quantity. Therefore, an experimental investigation of metals in which the cyclic plastic strain is the independent variable should shed new light on some of the basic aspects of the problem. From the practical point of view, there are many uses for information relating to the cyclic strain resistance of metals. One is the case of thermal stress fatigue where fatigue failure can occur as a consequence of a com- paratively few cycles of thermally induced mechanical deformation. Another is the mechanical working of metals where large cyclic strains are employed. In recent years several publications have appeared relating to the cyclic-strain resistance of metals,8-11 dealing mostly with the fracture aspects where the temperature is cycled simultaneously with the mechanical strain. Some work has been reported on the cyclic-strain resistance of metals at constant temperature, again oriented more toward the fracture aspects of the problem than the deformation aspects. 12-16 The present research investigation was undertaken to obtain information regarding the deformation characteristics of several metals whose structure-property relationships were simple and straightforward under conditions of both cyclic and monotonic strain. It has been shown for example that under cyclic-strain conditions some materials will strain harden, while other materials, particularly cold-worked structures, strain soften and these effects required further clarification.8,17-19 It was also de-

Jan 1, 1960