Search Documents

George W. Maynard, New York, N. Y.:—It is well known that there are many magnetite-mines of which the ore is too low-grade for direct use in the blast-furnace. For carrying out the sintering process, the preliminary step, in the case of magnetites, is the separation of the ore from the gangue by magnetic concentration. The resulting fine-grain product is very objectionable in the blast-furnace, and when used must be a very small percentage of the charge. The sintering process has saved the situation by furnishing a product which is absolutely ideal on account of its cellular structure. (In reply to questions by W. J. Tudor, and Joseph W. Richards, the following additional information was given by Dr. Maynard.) The percentage of iron in the product is determined entirely by the degree of concentration of the raw material and is practically not increased by the sintering operation. The magnetic concentrates at Port Henry and at the Benson and one or two other mines contain from 65 to 67 per cent. of metallic iron. The cost of sintering is from 39 to 41 cents per ton of product, including superintendence, depreciation, and repairs. The itemized figures are about as follows : Mixing (including labor), 24; power, 9; ignition, 5; repairs, 3; total, 41 cents. Prof. J. W. Richards, South Bethlehem, Pa.:—From a metallurgical standpoint I question the accuracy of the statement on p. 374: " C.—An increased reducibility of the iron so treated. (This has been conservatively estimated as 5 per cent. better than the best available ore.)" It seems to me that when a material is' sintered in this way, the constituents present, as lime, silica, and alumina, have a chance to form a compound with the iron oxide; that such a compound, if formed before the material goes into the blast-

Jan 1, 1913

By Lewis T. Wright

(Pittsburg Meeting, March, 1910.) I HAVE long been aware that ferruginous copper furnace slags if fused in the electric arc will yield metallic iron containing copper, and in order to confirm this knowledge, and to obtain further information of the behavior of such slags in the high temperature and reducing conditions of the electric furnace, a number of samples of slag were fused in an experimental electric furnace. The results obtained, given in Table I., show that a very large amount of metallic iron was produced, and that this iron carried with it practically all the copper, gold, and silver, and more than 50 per cent. of the sulphur, of the original slag. The metallic buttons formed in the electric furnace were clean, hard, but not brittle.

Mar 1, 1910

By William P. Blake

(Canal Zone Meeting, November, 1910.) A DEPOSIT of manganese-ore near Tucson, Ariz., merits notice by reason of the peculiar form in which it occurs, and as a striking. example of ore-deposition by vadose upward capillary flow of metal-bearing solutions with concentration at the surface of the country-rock. This deposit occurs at the northern end of the Coyote mountains, about 40 miles west of Tucson, upon the outcropping beds of porphyritic rock, which appear to be partly-metamorphosed strata of volcanic tufa, probably of late Secondary or of Tertiary age. The strata dip northward at a low angle, and present a series of basset-edges in parallel lines of outcrop, east and west, facing the south and extending over many acres. Successive groups of these outcrops, from 5 to 20 ft. in breadth, are coated with oxides of manganese in lustrous black films and crusts, shining in the sunlight like polished ebony, and covering the whole surface of the rock above the soil. Seen at a little distance, these croppings look like solid ledges of massive and pure ore; but closer inspection and a few blows of the hammer reveal their true nature as a superficial coating allied in origin to the blackened shining surface of rocks exposed in desert-regions, familiarly known as " desert paint" or "desert varnish,"' similar to the phenomena described by me in a former paper, but much thicker and heavier. * By reason of the death of the distinguished author, this communication, probably his last communication to technical literature, is published without revision of the proofs by him. A term first given y G. K. Gilbert. See Rocks, Rock-Weathering, and Soil; by George P. Merrill, p. 256 (New York, 1897). Superficial Blackening and Discoloration of Rocks, Especially in Desert Regions, Trans., xxxv., 371 (1905).

Sep 1, 1910

By JOHN BIRKNBINE

MR. NEILSON was born Aug. 12, 1842, at Philadelphia, Pa., where he died Dec. 30, 1906. His business career began with his graduation, in the class of 1862, from the Polytechnic College of the State of Pennsylvania. For a short time after graduation he was instructor in mathematics at the college, and then became associated with Messrs. Booth & Garrett, chemists, of his native city: In 1867 he was sent to the Adirondack mountains to care for mining interests of the late Jay Cooke, and spent about three years there, operating the forges at Elizabethtown, Essex county, N. Y. He also prepared an interesting monograph on Catalan forges and their operations. In 1868 he published a chart showing the material progress of the United States, and the cost of certain staple products during a series of years, which is believed to be the first of its kind issued in this country. In 1870 he made a trip to the Pacific Coast, prior to entering the service of the Pennsylvania Steel Company. In 1871, when the Logan Iron & Steel Co., of Burnham, Pa., failed, Mr. Neilson was appointed receiver, re-organized the company, became' its General Manager, and spent more than four years in this work. In the meantime, he became interested in the Freedom forge of the same place, and, with Mr. Wm. Burnham and Mr. Milton Brosius, laid the foundations for what is now the Standard Steel Works. From Jan. 1, 1877, to April 1, 1890, he was General Manager of these works, and closely associated with the Baldwin Locomotive Works. In 1878 he was in charge of the first consignment of Baldwin locomotives to Europe, which, with a picked crew of men from Baldwin's, he took to Eydtkennen, Russia, and placed in service. In 1890 he resigned from the Standard Steel Works and ac-

Jul 1, 1907

By H. H. Stoek

(Wilkes-Barre Meeting, June, 1911.) THE origin of the Mine-Rescue Service of the State of Illinois can be traced to two distinct sources, the work of the Rescue Station at Urbana and the Cherry disaster. During the early part of the year 1909, the Technologic Branch of the U. S. Geological Survey, now the Bureau of Mines, in connection with the Illinois Geological Survey and the College of Engineering of the University of Illinois, established at the University of Illinois, in Urbana, a branch rescue-station to supplement the work of the Pittsburg station of the Geological Survey. As a result of the work of training at the station in Urbana by R. Y. Williams, mining engineer, and James Webb, foreman of the Bureau of Mines, and the use of the helmets at several mine-accidents in the State of Illinois, . the people of the State were somewhat familiar with oxygen-helmets when the Cherry disaster occurred, in November, 1910. The oxygen-helmets were successfully used in connection with that disaster, and upon the recommendation of the Illinois Mining Investigation Commission, the Legislature of the State, assembled in special session during the winter of 1910, passed a bill appropriating $75,000 for the erection and maintenance of three rescue-stations, stipulating that they should be located in the northern, central, and southern parts of the State. The Act also provided that the stations should be in charge of a Commission of seven, two representing the United Mine Workers of Illinois, two the mine-operators, one the Federal Bureau of Mines, one the State mine-inspectors, and one the Department of Mining Engineering of the University of Illinois. This Commission was called together by the Governor of the State, Aug. 2, 1910, and since that time three stations have been located, built, and equipped: at La Salle for the northern

Dec 1, 1911

By A. J. McEvily, R. C. Boettner, C. Laird

The processes leading to fatigue failure in the low-cycle range were studied to obtain an understanding of the basis of Coffin's law. Particular attention was paid to the manner of mack nucleation and to the determination of the portion of the total lifetime spent in crack propagation. It was observed that cracks are nucleated at surface notches meated during reversed plastic deformation, Principally at grain boundaries, and that crack growth occupies greater than 75 pct of the fatigue life. When inclusions are present, they are often the primary sites of crack initiation. From consideration of the incremental distances advanced by a crack in each cycle and of the lifetimes of different materials, it appears that the universality of Coffin's law arises from the similarity of crack-tip strain for a given applied strain amplitude, irrespecti7:e of material. STUDIES of low-cycle fatigue have been particularly rewarding in that a simple correlation between fatigue lifetime and plastic-strain range has been shown to exist. This empirical relationship takes the forml,2 Nner=C [1] where N is the number of cycles to failure, Er is the plastic-strain range defined as the total plastic strain per cycle (the sum of the tensile plastic strain plus the compressive plastic strain), n, the exponent, is a constant independent of the material to a first-order approximation and often has a value of about 0.5, and C is a constant which for a number of ductile and metallurgically stable materials is approximately 0.65 for fully reversed strain.3 This relationship has been shown to be valid for a wide variety of metals and alloys and is often referred to as Coffin's law. However, it is yet not clear why so many different metals and alloys exhibit the same over-all behavior in the low-cycle range. Less is known about the mechanisms of fatigue failure in the low-cycle range than in the high-cycle range, but it is expected that the processes would have much in common. For example, an important characteristic common to both high-and low-cycle ranges is that fatigue crack propagation can occupy a considerable portion of the total lifetime. This has been shown by Laird and smith4 by a count of the number of ripples present on the fracture surface of copper specimens, each ripple corresponding to one cycle of load. On the other hand, some marked differences have been noted. For example, in copper,5 nickel, and aluminum4 there is a greater tendency for grain boundary cracking to occur as the strain amplitude is increased. The purpose of the present work was to study further the processes leading to fatigue failure in the low-cycle range and to obtain an understanding of the basis for the validity of Coffin's law. Particular attention has been paid to the manner of crack initiation and to the determination of the portion of total lifetime spent in crack propagation. MATERIALS A number of metals and alloys were tested, although more attention was focused on a particular few, once general trends had become apparent. Alloys were selected so as to investigate the effects of crystal structure, number of phases, stacking-fault energy, and impurity content. The materials in this grouping were: high-purity copper OFHC copper 1100 aluminum (commercially pure) 70-30 brass (Cu-30 wt pct Zn)

Jan 1, 1965

By N. O. Gray, John Henderson

Hydrogen-reduction data for naturally occurring single crystals and Prepared polycrystals of dense hematite have been presented. Results cover the temperature range 400o to 1000oC, for particles from ten sources, ranging in size from 0.07 to 10 mm and in shape from spheres to cylinders, cubes, and thin slabs. A consistent pattern of behavior has been demonstrated for single crystals and the reduction mechanism shown to be temperature-dependent. Below 579oC reduction is a simple topochemical process but at higher temperatuves it is complex and occurs in two distinct stages. Prepared particles from these laboratories behave in a similar manner to the single crystals. Data from two investigators showing topochernical reduction of Prepared particles above 575°C are inconsistent with that for other dense hematites. It is concluded that topochenzical reaction should not be used as a model for generalized rate expressions for dense hematites. SINCE 1958, McKewan1-6 has brought to prominence a simple concept of dense hematite reduction. This model is that oxygen is lost from a hematite particle undergoing reduction only from an oxide-iron interface that recedes in such a way that the oxide remaining retains the original shape of the particle, i.e., reduction occurs topochemically. An adjunct to this concept is that any intermediate oxides in the transition from hematite to iron only form thin layers so that oxygen cannot be lost from the particle without movement of the oxide-iron interface. Further, the rate of oxygen loss from the particle is said to be proportional to the area of the receding interface so that the iron layer grows linearly with time and the over-all reduction process can be described by the equation where ro and do are the initial particle radius and density, respectively, R is the fraction of the original oxygen lost, i.e., the fractional reduction, at time t, and K is the rate constant. The idea of an underlying simplicity in hematite reduction is attractive because it gives a tractable basis from which general theories of hematite reduction can be developed and it has received wide support,7-14 based mainly on the large amount of data13 that can be fitted to Eq. [I]. However, despite the fact that this equation has been derived for dense materials, the bulk of the data that have been used to test it13 have been for materials of only about 90 pct of theoretical density (5.26 g cm-3) or less, so that its generality for dense hematites has not been demonstrated. In any case, as will be seen, adherence of reduction data to Eq. [1] does not necessarily imply that reaction occurs topochemically. In this work only data for hematites approaching theoretical density are considered and it will be shown that in only one study besides McKewan's is topochemical behavior observed over the whole range of temperature investigated. For the majority of materials a linear rate of interface advance is observed to complete reduction only when wustite is not a stable intermediate phase in the transition of hematite to iron, i.e., at temperatures below about 575°C. Above this temperature, reduction is an exceedingly complex series of reactions that takes place in two distinct stages and it is only in the first stage that reaction in any way resembles a topochemical process. This means then that, far from representing general behavior as has commonly been supposed, topochemical reaction for dense hematites is only a particular behavior that may be observed under some circumstances. EXPERIMENTAL Hydrogen-reduction data have been collected and cross-checked in these laboratories by three techniques, weight loss, collection of water evolved in the reduction reactions, and direct metallographic examination. Details of these techniques are discussed elsewhere," where it is shown that results obtained by the three methods are in close agreement. The weight-loss method, by which most of the results were obtained, consisted of hanging the sample in a platinum mesh basket from an Ainsworth Model AV-AU-1 vacuum recording balance inside a vertical l 1/4-in.-ID alumina tube furnace. Dry deoxidized hydrogen was flowed downwards through the tube at 2 to 4 liters min-1 (stp). Single crystals from two sources and artificial oxides from three sources have been examined. The single crystals were from hematite deposits at Yampi Sound, Western Australia, and Brazil, the latter being obtained from Gregory, Bottley and Co., London, U.K. The "Yampi Blue" crystals were hand-picked from washed, magnetically concentrated, sized fractions, -200 mesh BSS (mean diameter ca 0.07 mm) and —36 + 44 mesh BSS (mean diameter ca 0.4 mm) while 10-mm cubes were cut from the Brazilian crystals with a diamond saw. The starting materials for the prepared particles were hematites designated, respectively, "Specpure Iron Oxide", Laboratory No. S639 from Johnson Matthey & Co. Ltd., London, U.K., "Calcined Ferric Oxide" from B.D.H. Laboratory Chemicals Division, Poole, U.K., and "Pigment Grade Oxide", EPR-50, from C. K. Williams & Co., Easton, Pa., U.S.A. Approximately spherical particles were prepared from the artificial oxides by rolling the material, moistened if necessary, in a glass jar, and cylindrical compacts approximately 10 mm in diam and of approximately equal height were pressed in a steel die at 200 psi. These spheres and cylinders were subsequently fired in oxygen for 20 to 100 hr at 1370°C. The

Jan 1, 1967

By Amitava Gangulee, Michael B. Bever

The effects of changes in short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions have been investigated. The heats of formation at 273°K of several alloys after two different thermal treatments were measured by liquid metal solution calorimetry. Their electrical resistivities were measured at temperatures ranging from 4° to 773°k. Tensile tests and microhard-ness measurements were carried out at room temperature. An effective short-range order parameter and an effective interaction energy are defined. The measured changes in the properties are interpreted in terms of these quantities. The short-range order parameter is evaluated separately from calorimetric and X-ray data; the results are in fair agreement. Increasing short-range order lowers the resistivity of- the silver-rich Ag-Mg alloys but does not measurably affect the temperature dependence of the resistivity. Short-range order increases the yield stress of these alloys but does not affect the ultimate tensile stress. Changes in the effective short-range order parameter independently obtained from measured changes in the heat of formation, resistivity, and yield stress are in fair agreement. THE thermodynamic, electrical, and mechanical properties of solid solutions have been investigated as functions of composition in many alloy systems, but the effects of configurational variables, such as short-range or long-range order, on these properties have received much less attention. The silver-rich terminal solid solutions in the system Ag-Mg are well-suited for the investigation of the effects of order. The composition of these solid solutions may be varied over a range extending to about 27 at. pct Mg.1 Appreciable short-range ordering is likely to take place in these solid solutions; the degree of short-range order can be varied by suitable thermal treatments. In the alloy Ag3Mg long-range ordering is possible.2 This paper is primarily concerned with the effects of short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions.-The long-range ordering transition is the subject of a concurrent paper.3 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Ag-Mg alloys containing up to 26.4 at. pct Mg were prepared by melting 99.99 pct pure Ag (obtained from Baker Chemical Co.) and 99.99 pct pure Mg (obtained from Eastman Chemi- cal Co. or Johnson Mathey & Co.) in graphite crucibles under molten potassium chloride. The solidified ingots were homogenized at 823°K for 10 days in evacuated Vycor capsules. A surface layer 6 in. thick was then removed by machining. The ingots were swaged into rods (2.5 mm diam) which were drawn into wires (1.0 mm diam). The wire specimens were annealed at 773°K for 24 hr in vacuum and either quenched into iced brine or cooled to room temperature over a period of 15 days. The average grain diameter (obtained from the linear intercepts) was about 0.1 mm. 1.2) Calorimetry. The heats of formation of the alloys were measured in a tin solution calorimeter as the difference in the heat effects of alternate additions of samples of an alloy and the mechanical mixture of its component elements. The additions were made from 273°K to the bath at about 623°K. The heat effect on addition of the alloys was approximately 5.5 kcal per g-atom. The procedure and the method of calculation have been described.4 1.3) X-Ray Diffraction. Short-range order parameters of two alloys were calculated from diffuse scattering intensities,' obtained with briquettes made from powdered specimens. A GE-XRD 5 diffractometer with filtered copper radiation was used. The absolute intensities were based on calibrations with paraffin. 1.4) Resistivity Measurements. The electrical resistivities were measured by a potentiometric method in which the potential drop across the specimen was compared with that across a standard resistance. For measurements below room temperature, the specimens were immersed in liquid helium (4°K), liquid nitrogen (78°K), dry ice and trichloroethylene (195°K), or ice and water (273°K). Measurements above room temperature were made on specimens held in a furnace under helium or in vacuum. The resistivity measurements were reproducible to ±0.5 pct or less. 1.5) Mechanical Tests. Tensile tests were carried out at room temperature with a Tinius-Olsen XY elec-tromatic Universal testing machine. Wire specimens (nominal gage length 1 in.) were used. The strain was measured with an extensometer, which had a sensitivity of 4 x 10-5; the strain rate was 10-3 min-1. Microhard-ness measurements were made with a square-pyramid indenter and a 100-g load.11 2) RESULTS AND DISCUSSION All measurements were made on two parallel sets of specimens, one quenched and the other slowly cooled from 773°K. The reported values are the averages of at least three measurements. In the range of magnesium concentration substantially below that of the composition Ag3Mg, quenched alloys have less short-range order than slowly cooled alloys. As the magnesium concentration approaches that of Ag3Mg, slow cooling develops long-range order. Quenching sup-

Jan 1, 1969

By C. W. Chen

MARTENSITE transformations in ß Cu-Al alloys have been studied by Greninger1 and other investigators. According to Greninger, the parent phase ß1 an ordered body-centered-cubic structure obtained from ß phase by suppressing the eutectoid decomposition, transforms into an ordered hexagonal-close-packed phase in composition containing 12.9 to 14.7 pct Al. The M, temperature decreases with increasing aluminum content; for the alloy containing 14.5 pct Al, for example, the ß1??' transformation occurs below room temperature. More recently, Kurjumow2 studied the transformation in ß Cu-Al alloys with the addition of nickel. His report stimulated new interest in the subject due to the observation of completely reversible transformation without hysteresis in the transformation temperature ranging from 10° to —10°C. In the present paper some characteristics are described of the transformation of Cu-Al-Ni alloys that were partly studied by Kurjumow. Experimental Procedure High purity copper (99.999 pct) and aluminum (99.99 pct) and electrolytic nickel were used in the preparation, by the Bridgman technique, of single crystal specimens which contained aluminum and nickel of 14.5 and 0.5 to 3.0 pct, respectively. Polished surfaces were prepared mechanically. Specimens were then chemically etched to remove distorted material, homogenized at 1000°C for several hours, and quenched drastically to room temperature in a 10 pct NaOH bath to produce the parent phase ß1. The transformation was studied under a microscope and, in some cases, recorded by means of motion pictures. A device similar to that designed by Greninger and Mooradian3 was used to cool and reheat the specimens. Results and Discussion When the specimens were cooled below room temperature, the ß1 to ?' transformation began at 10°C with the appearance of ?' crystals In relief, Fig. la. As the specimen temperature dropped further, the transformation continued, either by the growth of the ?' crystals, with the ß1 — ?' interface moving into the ß1 phase, Fig. 1c and 1d, or by the formation of new ?' crystals, Fig. 1b. As a consequence of the former process, banded structure is observed as a common feature of the low temperature phase. According to the theory of the formation of martensite by Wechsler, Lieberman, and Read,' the bands of ?' phase are probably twin-related, as is the case in the diffusionless phase change of In-T1 alloys,5 but this was not revealed by X-ray tech- niques. New ?' crystals, in needle form, often emerged suddenly across the ?' bands during the transformation. These acicular crystals then grew, both in length and in width, see Fig. 2a through 2d. The transformation on cooling is completed at about -35°C. Upon heating, the reverse transformation started at —10° C, in a manner nearly opposite to the transformation on cooling, and completed at 35°C. There was no noticeable change in the transformation temperature when the nickel content was varied within the limits previously mentioned. Through control of the specimen temperature, the transformation can be started, stopped, or reversed at will. This phenomenon has frequently been observed in the martensite transformation of many nonferrous alloy systems. Other systems are Au-Cd6 and In-Tl.5 ow-- ever, in the latter systems, the transformation is accomplished by single interface motion if the specimen composition is homogeneous and the temperature gradient in the specimen is uniform and sharp, whereas in the Cu-Al-Ni specimens, only multiple interface transformation is observed. The speed of the interface motion appears to be a functionof the rate of temperature change and the temperature gradient across the specimen length. In one case, in which the temperature increased at the rate of 10°C per min and there was no temperature gradient along the specimen axis, the speed of the disappearance of a ?' plate was determined, by the study of the motion pictures made, to be 26 µ per sec. Quench markings were observed on the polished surfaces of specimens. The markings were grouped into one or more sets of different orientations, and were parallel in each set. The ?' plates formed in subsequent transformation were parallel to the markings, indicating that the ?' plates and the quench markings had the same geometric relation-ship to the ß1 matrix. The quench markings on two intersecting surfaces of a specimen were therefore used in the determination of the habit plane of transformation, by the trace method suggested by Barrett.' Results obtained from five sets of markings in three specimens indicate that the habit plane is an irrational plane about 2" from one of the {221} planes. This is very close to the habit plane (3" from 221 planes) of ß Cu-Al alloys containing more than 13.0 pct Al.1 The martensite transformation of Cu-Al-Ni alloys is reproducible. No sluggishness was found between consecutive transformation cycles, although a slight difference in the distribution pattern of the ?' plates was observed, compare Figs. Id and 2d. The transformation can be strain-induced. This characteristic has been tested by a simple method. When a specimen was elastically strained slowly in a vise, ?' plates were gradually produced in the same fashion as during transformation on cooling, This test was done at room temperature, and thus above the M,

Jan 1, 1958

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By Peter K. Strangway

During 1973, a 20,000 net ton (18 100 metric ton) formcoke test was carried out at Inland&apos;s 26.5-foot (8.08-meter) hearth diameter on NO. 5 Blast Furnace. The formcoke briquettes were produced from Elko1 coal by FMC at their pilot plant in Kemmerer, Wyoming. The briquettes were shipped to Inland in open railroad cars and most of them were placed in an outside storage field until a sufficient amount was available for the actual blast furnace test. The test consisted of three phases: an initial four-week base period; the actual 33-day formcoke test period; and a final three-week post-test base period. During the formcoke test period, the regular coke skip loads were gradually replaced with skips of formcoke until, after a three-week period, the replacement ratio reached 80%. The furnace operated smoothly and quality hot metal was produced. The burden remained permeable and it was possible to maintain wind rates 9 of over 100,000 scfm (47 Nm3/s) without significant blast pressure increases. Dusting from the formcoke was not a problem either in the stockhouse or in the top gas. The formcoke briquettes maintained their original shape and density as they descended through the furnace. When the 80 percent replacement level had been reached, the inwall temperatures became higher than normal (about 2000 ºF (1090 ºC)) and followed an unusual steady pattern. In addition, the top gas temperature became higher than normal, and the hot metal analyses and temperatures began to fluctuate unacceptably. In general, it is felt that the high inwall temperatures were a result of channeling of the hot furnace gases along the stack walls. This channeling appears to have been promoted by a change in distribution of the burden in the top of the furnace which, undoubtedly, was caused by the increased increments of formcoke. Since it was felt to be unsafe to operate the furnace for an extended period of time with the inwall temperatures at the high level, a decision was made to remove the formcoke from the furnace. When this was done, the inwall temperatures returned to normal. Once the inwall temperatures had returned to normal, the remaining 3,800 net tons (3450 metric tons) of formcoke were used in the furnace at a nominal 40% replacement level for five continuous days. The furnace operated smoothly during this period, and the results were representative of satisfactory furnace operation with partial replacement of regular coke with formcoke. The test was successful in proving that formcoke can replace up to about 50% of the regular coke in a large furnace operating at high wind rates. However, additional work will be required to develop acceptable charging practices for using higher levels of formcoke replacement.

Jan 1, 1977

By William R. Webster

I have continued the investigation of the Pottstown Iron Com pany&apos;s basic Bessemer keel plates on the line referred to in my paper of last October (Trans., xxi., 766)) and have added a study of the hardening effects of sulphur, which were not taken into account at that time. The results are so encouraging that I now give them in full. For some months we have graded all the steel at these works by the table given in my former paper, and checked the grading by the forging-tests as described in the paper of Mr. Joseph Hartshorne, read at the same meeting (Trans., xxi., 748). The steel thus graded was bloomed for the plate orders. Then one slab was rolled into a plate for the order, and a tension-test was made of this plate. By the result of this tension-test we were guided in rolling the balance of the heat. Out of several hundred heats graded in this manner, 95 per cent. met the requirements of the orders in every respect, and were accepted; but these results will no doubt be improved upon, when the influence of sulphur is also considered.. The hardening effect of sulphur seems to be about 500 pounds per each .01 per cent. of increase. In the table accompanying the pres ent paper, the ultimate strength with .06.5 per cent. sulphur agrees with the old table where sulphur was not considered; that is, for all steels with less than .065 per cent. sulphur we now get lower re sults, and for those with more sulphur, higher results. Making this allowance for sulphur, the assumed ultimate strength of a 3/8-inch plate of pure iron is reduced from 38,000 pounds per square inch to 34,750 pounds. With this as a basis, I have constructed my new table, giving each of the elements, carbon, phosphorus and manganese the same hardening effect as before, to wit : Carbon is credited with a constant effect of 800 pounds per each, 0.01 per cent. Phosphorus shows greater effect in high-carbon than in low-carbon steels. For 0.07 and 0.08 C, it has about the same effect as carbon, that is, 800 pounds for each .01 P. This increases to 1500 pounds per .01 P in 0.15 C steel, or nearly twice the effect of carbon. This

Jan 1, 1894

By Charles G. Maier

SCIENCE beginning in rational observation came of age, when its devotees first began to measure and count. It has been said that the most striking aspect, of science today is its growing abstraction, and its preoccupation with mathematical symbolism. Technology with specific and concrete objectives in the satisfaction of human wants, cannot conceivably achieve the abstract unification that science seeks, but .the utility of the&apos; scientist&apos;s method has been too well proved to require bolstering. Metallurgy is in its scientific infancy.

Jan 1, 1931

By James P. Roe

I. INTRODUCTION. THOSE who deem the subject of this paper an old and super¬seded one may recall with advantage the words of the great proverb-maker, bidding us to seek the new in the ashes of the old. The manufacture of wrought-iron began with the small hearth built upon an eminence, and relying on the wind for blast. Next came, either the hearth about 12 in. in diameter by 2 ft. in height, blown by a man operating two goat-skins for bellows, or, a hearth of greatly varying diameter and about 10 ft. high, depending for its blast upon natural draft. The former appeared in India, the latter in Burmah; and both were in operation until quite recently, though their origin is lost in prehistoric times. The Catalan forge was the evolutionary descendant of the foregoing, and the parent of the Blase-ofen, which in turn led to the high bloomary or " Stückofen," the father of the blast-furnace, as a producer of cast-iron. The production of cast-iron checked the growth of the direct processes; and led to the introduction of various hearths, such as the Walloon, for low-silicon irons; and the South Wales process, combining the run-out fire with the finery, for higher-silicon irons. Some of these are still in operation in localities possessing the necessary raw materials; and their product is used for purposes requiring wrought-iron of exceptional quality, the supply of which is still smaller than the demand. We have to look back but a century and a quarter to see the introduction of the puddling process by Henry Cort; a process which, reinforced by the iron-oxide bottoms and fettling of Hall, was not less revolutionary in character, and more revo-

Jul 1, 1905

By Yeatman, Pope

FOR many years geologists have felt that mining companies should adopt a more liberal policy in the publication of their reports. The increasing usefulness of the geologist to the mining profession in recent years demands that consideration be given to this question. Prior to 1900, the call for geologists of high reputation by mining companies was probably mainly in connection with lawsuits arising from the interpretation of rights or ownership as defined by the "Law of the Apex," and from problems such as finding the continuation of the vein or whether the vein followed was the main one or a branch. Later, outside of legal questions, the most intensive and general use of their services arose from the search for oil. Geologists to determine the position of the formations

Jan 1, 1938

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M.. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information-will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries: All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute. can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will he classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 5, 1913

By Hermsdorf, Richard P. E.

AMONG the newer lead smelting and refining plants of the country is that of the United States Metals Refining Co., at Carteret, N. J. Not only is the technical practice here modern and efficient, but exceptional care is taken to assure healthful operating conditions for the employees. One large building houses the entire department, which includes, as its chief units, one reverberatory smelting furnace, one blast furnace, two softening furnaces, one utility reverberatory furnace, two Faber du Faur retorts, five 120-ton kettles, three 60-ton antimouial lead kettles, and one 5-ton kettle for experimental purposes. There is a 10-ton overhead crane in the kettle aisle, which is also used for shipping lead. Other auxiliary equipment is referred to in the outline of operations. A general plan of the plant is shown in Fig. 2, and a general view in Fig. 1. Primary smelting operations are conducted in a 30 by 11-ft. reverberatory furnace with bottom, roof, and upper walls of clay brick, magnesite

Jan 1, 1934

By Walter Harvey Weed

The notes given in this paper, the result of observations made during recent brief professional trips to the northern States of Mexico, are offered as a slight contribution to the geological knowledge of a region little known, but long famous for its rich gold- and silver-mines. They are not detailed geological studies, but they contain, I believe, the salient facts. The following districts were visited: 1. Santa Eulalia (silverlead) ; 2. Parral (silver-lead); 3. Las Vigas (copper); 4. Jimenez (copper); 5. Guadalupe y Calvo (gold); 6. La Cumbre (gold); 7. Palmarito (silver); 8. Cananea (copper); 9. Sierra Pinitos (gold); 10. Sierra Azul (gold). 1. The Santa Eulalia Silver-Lead Deposits. Seventeen miles SE. of Chihuahua is the mining district of Santa Eulalia, to which that city owes its origin and long prosperity. Discovered in 1703, this district has been, and still is, one of the great silver-lead producers of the world. For 86 years after its discovery, the total output upon which the crown tax was paid amounted to $112,000,000. Worked until within the last 20 years by the most primitive methods, without machinery of any kind, the deposits continued to yield a vast treasure of silver; at present the yearly tonnage far exceeds that of former times. A broad-gauge road runs from Chihuahua up the valley of a small creek to the village of Santa Eulalia, which is situated within the borders of the mountains of that name. A few miles out of Chihuahua a narrow-gauge railway, owned by the Chihuahua Mining Co., branches off to the mines. This road ascends a smooth but steeply-rising plain to the base of the mountains, and winds about the slopes until the mines are

Jan 1, 1902

By A. A. Bauer, M. S. Farkas, F. A. Rough

An investigation of the d-phase relationships between the uranium-zirconium and uranium-molybdenum systems was conducted. A ternary cut joining U-31.5 at. pct Mo to U-74 at. pct Zr is presented on the basis of differential thermal analysis, metallographic and X-ray diffraction data. HyDothetical isothermal ternary sections, inferred from the determined d-phase relationships, are presented for the uraniztm-zirconium-molybdenum system. A ternary eutectoid, at 454ºC, was found in zirconium-rich alloys. Its composition, based on metallography and electron-beam micro-analysis, is estimated as U-61.7 at. pct Zr-7.1 at. pct Mo. URANIUM binary systems have been studied extensively in the past to supply basic information needed in reactor-fuel development. Alloys of uranium with zirconium, molybdenum, and titanium are of particular interest because, in these binaries, extensive or complete solid solubility between the body-centered-cubic forms of these elements and y uranium exists. In addition, an intermediate phase of limited solid solubility forms in each of these systems by transformation of the high-temperature ?-uranium phase. Previous investigation of the phase relationships existing between the intermediate 6 phases in the uranium-zirconium-titanium and the uranium-molyb- denum-titanium ternaries have already been reported.1,2 The results of an investigation of the phase relationships existing between the 6 phases in the uranium-zirconium-molybdenum system is reported here. The phase equilibria that occur in the solid-state portions of the pertinent binary systems are shown in Fig. 1. Phase nomenclature appearing throughout the report is as shown in these diagrams. The crystal structure of the phases in this system are given in Table I. EXPERIMENTAL PROCEDURES Alloys were cast and fabricated to 1/4-in.-diam rod. Specimens were heat treated and examined by metallographic and X-ray techniques. Thermal-analysis data were obtained.

Jan 1, 1960

By T. L. Joseph

LARGE deposits of manganiferous iron ores, representing several million tons of metallic manganese, occur in the United States. The Minnesota deposits of such ore-are of outstanding importance because of their size, state of development, ease of mining and proximity to the Great Lakes, which permits water transportation to steel centers. In&apos; view of the fact that our steel industry requires large quantities of manganese, for which no satisfactory substitute-has been found, and because our reserves of ferro-grade ore are comparatively small, the development of methods that will make our large deposits of manganiferous iron ores available as a source of ferromanganese is an important problem. Realizing the importance of this problem, some years ago the North Central Station of the U. S. Bureau of Mines and the Minnesota School of Mines Experiment Station undertook jointly the development of methods for recovering the manganese content of manganiferous iron ores in a: form suitable for the production of ferromanganese, the 80 per cent. alloy indispensable in producing steel. Two types of manganiferous iron ores have been described in previous reports. I The brown ores are higher in iron and lower in manganese than the black ores; the black ores are more siliceous but contain less phosphorus. The utilization of the iron content of the brown ores in the production of steel appears to furnish the best basis for their treat-ment. The method of attack has been to work out modifications in iron and steel practice so as to recover manganese in the form of slag comparable to ferro-grade ores. The greater part of the experimental work has been conducted with a 6-ton blast furnace and a Y2-ton basic open hearth. This paper is devoted mainly to open-hearth tests in which high-phosphorus spiegel

Jan 1, 1930