Search Documents

By Harlowe Hardinge, R. C. Ferguson

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year's time.

Jan 1, 1950

By R. S. Wagner, R. G. Treuting, W. C. Ellis

Use of the Weisseizbevg goniometer for the study of the morphology of whisker crystals and transfer of the results to a stereograplzic projection are described. While in almost all instances a complete and rapid solution is obtained with a purely gaphical treatment, an absolute analytical treatment applicable to difficult cases is given. Examples are given for determination of growth direction and external features of a crystal, for detection of 'twintzittg, and for establislting the orientation relntionships in a kinked whisker crystal. We give here a method for the use of the Weissen-berg goniometerl" in the study of orientation relationships in "whisker" (micro) crystals3-8 and direct transference of the data to the stereographic projection. The operations are straightforward and require no involved calculations: in almost all cases solely graphical treatment is adequate. In a few complex instances, a more exact analytic method may be required. In the method, not only are equatorial reflections of an oscillation photograph used, but also those on higher layer lines, or those not occurring on a recognized layer line. Such reflections off the zero level are often essentialy to detect the presence of twinning. The method is particularly suitable for examination of whisker crystals since the axial or growth direction is almost always one of high symmetry, permitting a more restricted oscillation range to obtain the necessary reflections and an accordingly shorter exposure time. The method is also applicable when there is no lattice-related external symmetry, and is as well able to identify external crystal surfaces, when such exist, with the aid of an optical beam. Thus growth direction, identification of lateral faces, twinning, and orientation relationships in a kinked crystal can be established. A test for the Eshelby twist6-8 can readily be made. The method can be used for orientation, for structure analysis, and as an aid in the identification of an unknown crystal. Moving-film techniques have previously been employed variously for crystal-orientation studies.1,2,9-13 In particular, use of the Weissenberg method for orientation determination has been reported by Wooster and wooster.14 While their method derives the same data as here described, it differs in depending on the tracing of constant p streaks, a less than dependable phenomenon with small specimens, a few microns or less in cross section. The Laue method can and has been used for orientation studies of microcrystals,15 e.g., 2 p in cross section, but requires the extreme intensity and concentration from a microfocus tube to obtain reasonable exposure time. PRINCIPLES OF THE PRESENT METHOD Consider a crystal of random orientation with respect to the oscillation axis in a Weissenberg goniometer. Its diffraction pattern need not necessarily result in recognizable layer lines. In Fig. 1, a stereo-graphic projection of the reference sphere is given with the equatorial plane XZ normal to the oscillation axis Y, and the X-ray beam directed from X towards 2. The great circle ZZ is then normal to the beam, and the axes are right-handed. Thus the reflected X-ray beam lies at the intersection R of small circle ARB of radius 28 from 2, and of small circle RE of radius a from the rotation axis Y. a is the conventional semiapex angle of a cone of diffracted rays from the atoms aligned in the direction

Jan 1, 1967

By George P. Chapman

Mica is a platy mineral occurring in a variety of complex hydrous aluminosilicate forms with differing chemical composition and physical properties. Principal minerals in the mica group include: Muscovite-potassium mica (colorless or pale green/ ruby) Phlogopite-magnesium mica (dark brown or amber) Biotite-magnesium-iron mica (black or dark green) Lepidolite-lithium mica (lilac) Selected properties are given in Table 1. Muscovite is most important commercially with phlogopite of lesser use. The laminated structure of mica enables it to be split into very thin films which are transparent and tough as well as having outstanding dielectric and insulating properties. Commercially, mica is used in a number of forms (Chowdbury, 1941; Rajgarhia, 1951; Skow, 1962). Sheet mica consists of flat sheets mined from naturally occurring books of mica, free from defects and capable of being punched or stamped into required shapes. Sheet mica is separately classified into blocks, films, or splittings according to thickness. Built-up mica, or micanite, is made by arranging overlapping splittings in layers , cemented with a binder and pressed together at high temperature. Reconstituted mica, or mica paper, is made by depositing fine flakes of high-quality scrap mica in a continuous film impregnated with binder. Scrap and flake mica are normally unsuitable in quality or size for making sheet mica. Originally the term scrap mica referred to the waste byproduct of mining and fabricating sheet mica, and distinct uses were developed for this material. Subsequently it became economically feasible to mine lower quality mica for these uses, and the term flake mica was introduced. Although the two terms are still used somewhat synonymously, it is considered better, at least in the United States, to use the term flake mica in referring to mica mined for uses other than as sheet mica; and to restrict the term scrap mica to mica mined for or with sheet mica, but which will not meet the specifications. Synthetic mica, such as fluorophlogopite, is produced by slow crystallization of a melted blend of pure raw materials. Mineralogy In the true sense the term mica does not relate to, a particular mineral, but to a group or family of minerals of similar chemical composition and to some extent similar physical properties. These minerals are predominantly potassium aluminum silicates with varying amounts of magnesium, iron, and lithium. The precise formulas and isomorphic relationships of the various group members have been studied, but general agreement has not been reached (Grimshaw, 1971; Hurlbut, 1952; Skow, 1962). The general formula describing the chemical composition of micas is [X2Y4-6Z8020(OH, F)4, where X is mainly K, Na, or Ca; Y is mainly Al, Mg, or Fe; Z is mainly Si or Al (Deer, et al., 1962).] These minerals have an internal structure of the layered lattice type where the silicon atoms are in the center of a tetrahedral grouping of oxygen atoms. The groups are linked together in a single plane by three oxygen atoms that lie within the common plane. Each of these oxygen atoms is shared by two tetrahedra. These linked tetrahedral groups, when continually extended, produce a hexagonal network within the plane. This internal structure of the mica has been used to explain the ex-

Jan 1, 1983

By L. G. Jones

An approximate method of calculation is developed in this paper which allows duplication of radial unsteady-state gas flow computer results where Darcy's law applies, such as those reported by Aronofsky and Jenkins and Bruce, Peaceman, Rachford, and Rice. Moreover, the new calculation method can be used to obtain results for radial unsteady-state gas flow obeying the quadratic flow law proposed by Duwez and Green. Means are discussed for predicting well behavior at single or superimposed flow rates in finite or infinite reservoirs, determining reservoir rock properties from well-test data, reproducing and interpreting back-pressure test data, and determining the radial extent and reserves of gas reservoirs from well-test data. Example calculations are presented for gas flow following both Darcy's law and the quadratic flow law. INTRODUCTION Since the publishing of U. S. Bureau of Mines Monograph 7,1 most gas-well testing methods have been based on the equation q = y (pl2 - pw2)a, where q = production rate, pl and pw, are formation pressure and sandface pressure, respectively, and y and a are constants to be obtained from test data. These methods, used for predicting both deliverability and "open-flow" capacity of gas wells, have been useful and accurate in many cases but unsatisfactory in others. Even at best, however, they do not supply information about the formation or lead to an understanding of nonsteady-state gas flow in porous media. Many theoretically based studies2-4 of gas flow obeying Darcy's law have been made.' Since the partial differential equations which result from combining Darcy's flow law with the continuity equation are nonlinear, most of the published research consists of either numerical solutions or analytical solutions for linear approximating equations. Such solutions have been of limited value in field work due to their unhandy form and their failure to correlate most field data. There is evidence5,6 which indicates that Darcy's law is inadequate to describe gas flow at some flow rates of practical interest. A quadratic flow law: which reduces to Darcy's law at low rates, is more successful in accounting for experimentally observed behavior. This flow law has been applied successfully to a few hypothetical reservoir cases in work which has recently been published.10 However, these numerical solutions of the equations involved have been successful only on a special analog computer. Routine applications to field cases would be awkward and have not been attempted. The present paper describes an approximate method for computing nonsteady-state gas flow solutions which has been completely successful in predicting the results for both Darcy flow and quadratic flow obtained by elaborate numerical methods. The new calculation method allows determination of the observable variables in gas-well testing at constant rates. It is similar to the scheme of using a succession of steady states suggested by Muskat7 in that it makes use of steady-state and material-balance equations. It also is similar to the work of Aronofsky and Jenkins2 in that the new method includes Aronofsky and Jenkins' stabilized flow equation as a special case. It improves upon both of these calculation schemes in that it accurately describes all portions of reservoir history and suggests means of determining reservoir rock properties from well-test data. This paper deals only with production from a reservoir, in which case the rate is defined as being negative. The reservoir studied here is a homogeneous, disk-shaped porous body of uniform thickness, with all boundaries sealed except the inner radial boundary of the well.

By W. C. Hagel, H. J. Beattie

Phases present at 2200° and 1500°F (1204° and 816°C) were identified in sixty wrought developmental austenitic alloys possessing wide compositional variations. The bases were iron-, cobalt-, and nickel-rich as well as a base with equal parts of each. There are only two structure types previously not found in similar alloys, viz .-the Co3 W and the Fe3Al types. A molybdenum-rich monocarbide decorates dislocations with unusual clarity. Other results provide correlations between alloy composition and phas e precipitation. Grouping intermetal -lic phases into three general classes : I) geometrically close-packed, 2) topologically close-packed, and 3) bcc derivatives, the nickel base prefers the first, the iron base the second, and the cobalt base the third—each base tending to shun the other two classes. Thus, a crystal-chemistry effect previously noted by Laves and Wallbaum can he expanded for these Group VIII elemental bases. There appear to he no quaternary or higher -order structure types requiring more than three atomic species. AFTER studying aging reactions in many diverse commercial austenitic alloys1-4 as a function of detailed time-temperature variations in heat treatment, it became apparent that matrix composition influenced structure types and morphologies to a large extent. These tendencies were related4 to a crystal-chemistry effect uncovered by Laves and Wallbaum.5,6 We have now directed our efforts to exploration of the whole ternary field, covering the standard base elements—iron, cobalt. and nickel— with 10 to 20 pct Cr and moderate amounts, up to 10 pct, of the usual alloy additions. Solutioning and aging treatments were held constant with major emphasis on X-ray identification of microconstituents. The possible existence of exceptions to the Laves-Wallbaum effect, or any new phases, was sought. Phases appearing in austenitic alloys can be classified as geometrically close-packed (gcp), octahedral or nonoctahedral interstitial compounds, topologically close-packed (tcp), semicarbides, and bcc derivatives. Crystal structures of the first four classifications can be visualized as a dense packing of semirigid spheres of different sizes, while the bcc derivatives represent a less efficient packing of spheres. The Laves-Wallbaum effect involves the gcp and tcp phases. Gcp phases possess both tetrahedral and large octahedral interstices; examples are Ni3Ti(n), NiSAl(y'), Co3W(E), and other ordered AB3 compounds where B atoms are smaller than A. Their precipitation is primarily intragranular, presumably coherent with an austenitic matrix, and a chief source of strengthening. Most octahedral interstitial compounds (e.g., CbC, Tic, TiN, Mo2C) have a gcp lattice of large metal atoms which accommodate small carbon or nitrogen atoms in the octahedral interstices. The compound Ti2SC, previously designated Y phase or T phase, can, with some reservation due to its partial co-valency, be placed in this category.7 The nonoctahedral interstitials (e.g., M7C3, Fe3C) represent close-packings of spheres in structures that provide larger triangular-prism interstices for carbon, since the octahedral interstices formed by chromium and iron atoms are too small. Tcp phases possess only tetrahedral interstices; examples are Laves (Fe2Ti, Fe2Cb, Fe2W...AB2), p(Fe7MO6, Co7W8.... A8B7), and (FeCr, Co2Cr3)

Jan 1, 1965

By H. H. Rachford, D. W. Peaceman

A system of partial differential equations describing miscible displacement of fluids in porous media is derived The system takes into account the influence of gravity, the spatial distribution of permeability, diffusion, and fluid viscosities and densities. A numerical procedure for approximating solutions to the differential systems has been tested for a horizontal two-dimensional geometry. In end-to-end displacements of oil with less-viscous solvents, the numerical solutions exhibited fingering qualitatively similar to that observed in laboratory models. Small random spatial variations in permeability about the mean value are sufficient to initiate fingering. Quantitative comparisons of computed results with laboratory data show good agreement. INTRODUCTION Miscible flooding of oil by solvent is receiving increasing consideration for field use.1-4 Unfortunately, such floods potentially present severe problems in loss of recovery through the by-passing of oil by expensive solvent. Consequently, their economic evaluation requires sound techniques for predicting recovery. The purposes of this work are to present a finite-difference method for calculating the multidimensional displacement of oil by solvent and to investigate the validity of the method by comparing results of calculations with data from displacements in laboratory models.5 The formulation of the method to simulate the model experiments treats a case of limited scope in the description of solvent flooding in the reservoir. The model experiments were carried out with fluids that were assumed to form an incompressible, ideal, two-component system with constant diffusivity. Establishing the validity of the method even in its present form provides a major step toward the goal of quantitatively evaluating individual solvent flooding projects. First, it demonstrates the fea- sibility of calculating the course of displacements which are dominated by an inherent macroscopic instability, i.e., viscous fingering. In addition, the method provides almost the only practical means of examining the effect of the size and extent of reservoir inhomogeneities on the development and propagation of the fingers, taking into account the important influences of diffusion and gravitational segregation. It might be inferred that such studies cannot yield results of practical value because in displacements dominated by macroscopic instability the pattern of finger development and the resulting performance should depend critically on small variations in the geometric distribution of reservoir inhomogeneities. The present method offers the capability inherent in computational techniques of predicting performance reproducibly with any arbitrary distribution of reservoir properties and, as such, provides a means of evaluating the sensitivity of behavior to uncertainties in reservoir definition and, thus, assessing the reliability of prediction of performance. THE PHYSICAL PROBLEM DATA USED FOR QUANTITATIVE TESTS OF CALCULATIONS In this work, a calculation for treating the miscible-displacement process is tested by comparing calculated results with experimental data. The experiments chosen for comparison have been described in detail,5 and the quantitative features are summarized in a later section. Briefly, oil was flooded by solvent of equal density from a thin rectangular channel in Lucite packed with uniform Ottawa sand. Under these conditions, two-dimensional geometry is considered adequate to represent the process. Inasmuch as the present work is concerned with testing of the method by comparison with specific two-dimensional data, the system of equations presented in the succeeding section will be oriented to defining the physical system specifically. THE DIFFERENTIAL EQUATIONS Suppose x, y to be a Cartesian co-ordinate system and define h(x, y) to be the height of a point above a horizontal reference plane. It will be assumed

By D. W. Fuerstenau

Recently R. J. Charles1 showed that comminution of brittle or semi-brittle materials in batch operations is described more appropriately by a variable energy relationship than by the specific relationships proposed by Rittinger,2 Kick,3 and Bond.' That is, the value of n in the empirical differential operation which applies to crushing and grinding (Eq. 1) is variable. Independently, Holmes' developed an identical generalized equaton for size reduction. The experimental data of Charles and Holmes show that the value of n is determined by the material and the comminuting machine and is constant for a given combination of these two conditions. The general objective of the present article is to extend the Charles-Holmes concepts to continuous ball milling. The specific objective is to analyze the operation of a vibratory ball mill dry-grinding chromite in a continuous open circuit and to develop an equation for the comminution of chromite in this mill. Basic Principles: In a batch mill the length of time during which the material is ground is a direct measure of the energy expended on the material, except possibly for exceedingly fine grinding. However, in a continuous operation, the fraction of the total expended energy which is useful for grinding will vary according to feed rate and amount of material in the mill. If the amount of material within a continuously operating vibratory mill is low enough so that only part of the expended energy is used for grinding, the extent of size reduction at constant power input must depend upon the length of time the material is retained within the mill, namely, upon retention time. The following analysis pertains to a continuous mill operating under these conditions. The empirical differential equation that applies to the comminution of brittle materials is:" dE = -Cdx/x" [1] where dE is an infinitesimal energy expenditure, C a constant, dx an infinitesimal size change, x the particle size, and n a constant. For continuous grinding in an open circuit at constant power input, P, Eq. 1 must be written as (dtr)P = -C dx/x" [la] where dt, is an infinitesimal time during which a particle of size x is in the mill, and C' is a constant. A ground product never consists of particles of single size but always comprises a distribution of sizes. In comminution, the expenditure of energy causes a lateral shift in the size distribution.', ' " The general objective of any engineering study of comminution is to correlate the magnitude of this size distribution shift with the energy expended, the ultimate aim being to cause the greatest shift with the least amount of expended energy. Although a number of criteria can be used to measure this shift, Schuhmann's size modulus has been found convenient.' Mathematically, the Schuhmann size distribution can be expressed as follows:" y = l00(x/k) [2] or in differential form: dy = [F- xa-' dx ] K, where y is percentage of material finer than size x, a is a constant that determines weight distribution among particles of various sizes, and k the size modulus that denotes the theoretically maximum-sized particle in any size distribution. By considering the energy required to reduce an element of weight of material, dy, from size x, to size x, the element of time during which the material must remain in the mill at at power will be (dt..).= J'-Cax!(dy) [3] Summing up all the elements of weight from zero to 100 for a product that conforms to the Schuhmann size distribution yields C C f Cdx,\( 100«x°-'dx\

Jan 1, 1960

By C. F. Floe, M. Cohen, M. B. Bever, V. G. Paranjpe

NITROGEN is becoming recognized as one of the important elements in ferrous physical metallurgy. Several investigations indicate that nitrogen plays a significant part in such phenomena as strain aging and temper brittleness. Nitrogen is known to be a powerful austenite stabilizer and may be a useful alloying element in stainless steels. The hard-enability of steels has been found to be increased by nitrogen. The nitriding and carbonitriding pro- cesses are examples of successful industrial application of nitrogen in ferrous materials. For a complete understanding of the various roles played by nitrogen in ferrous metallurgy a knowledge of the phase relations in the binary iron-nitrogen system is essential. The literature contains a variety of iron-nitrogen phase diagrams. Those suggested by Fry, Sawyer,² Epstein and his coworkers,³,4 Lehrer,5 Eisenhut and Kaupp, and Hägg7,8 differ significantly from one another. Moreover, the most recent of these investigations dates back about twenty years. A re-determination of the entire diagram, therefore, appeared desirable. In addition to the published phase diagrams, investigations have been carried out on portions of the iron-nitrogen system. Bramley and Haywood determined the composition and temperature of the iron-iron nitride eutectoid. The maximum solubility of nitrogen in a iron was investigated by Portevin and Seferian10 and by Diikstra. 11 Several investigators have determined the crystal structure of the various iron-nitrogen phases. In fact, Eisenhut and Kaupp6 and Hägg7 based their entire phase diagrams on the results of such studies. Epstein' and Emmett12 reported lattice-parameter measurements on the E (hexagonal close-packed) phase. Osawa and Iwaisumi13 also studied the change in lattice parameters of the a, ? and E phases with nitrogen content. Brill" and Hägg7 showed that the y' phase has an ordered structure, and Hendricks and Kostingsl5 suggested a structural relation between the E and phases. In a recent investigation Jackl6 arefully studied the super-lattice reflections from the y' and phases. Experimental Procedure A large variety of experimental methods has been used by previous investigators in studying the iron-nitrogen system. These methods include thermal analysis, microscopic examination, X ray diffraction, magnetic measurements, dilatometric analysis and anelastic experiments. Thermal analysis is of low accuracy in determining changes in the solid state. This accuracy is further decreased for iron-nitrogen alloys since composition changes will occur during heating or cooling unless extreme care is taken to use a proper atmosphere. Metallographic methods are of small value . because homogeneous iron-nitrogen alloys of sufficient size can be produced only with great difficulty. The dilatometric method is open to the same objections as thermal analysis in that changes in composition may occur during heating and cooling. Lattice parameter measurements by X ray diffraction can be used satisfactorily for determining phase boundaries if cooling is fast enough to prevent structural changes. In view of the limitations of the various other techniques two methods only were adopted in this investigation, (1) X ray diffraction measurements, and (2) a controlled nitrogenizing method. The second method is an innovation for investigating the iron-nitrogen system, and will be described at length. Materials: All iron-nitrogen alloys were prepared from carbonyl iron powder of the analysis shown in table I. The average particle size was about 20

Jan 1, 1951

By R. E. Robbins, H. R. Brager

THIS note describes an unusual result obtained in an electron microscope investigation of cavities produced in commercial type 304 stainless steel irradiated in a thermal reactor (ETR) at 290°C to a high neutron flu-ence, 6 x loz1 n per sq cm. The analysis of the steel used is given in Table I. The unusual result is that the calculated quantity of helium gas produced by transmutation during the irradiation, 12 ppm, is less than one-tenth the amount of gas necessary to balance the surface tension of the observed cavities produced in the steel during ETR irradiation. Therefore, the cavities would be expected to behave like voids; however, they behave like "gas filled" bubbles. The maximum quantity of helium produced in the steel by B" transmutation was 8 ppm. In addition, the amount of helium formed by (n, (1) fast neutron reactions with the major alloy constituents and nitrogen was calculated to be 4 ppm based on the tabulated differential or effective fission-averaged cross sections of elements in type 304 stainless steel irradiated in typical thermal reactors.', In previous investigations concerning commercial austenitic stainless steel irradiated in a thermal reactor, the amount of helium gas calculated to be produced by transmutation has always been significantly greater than the amount calculated on the basis that the bubbles were gas filled, PPs= 2y/R. The balance of the gas was assumed to be in bubbles smaller than could be detected on the electron micrographs. Accordingly, the bubbles were attributed to helium produced from transmutation of impurity boron by thermal neutrons. These bubbles were not uniformly dispersed in the matrix but were located principally at grain boundaries, or were radially positioned around a few precipitates located in the matrix and at the grain bundaries., 4 Voids have also been observed in austenitic stainless steel irradiated at high temperature to high neutron fluences in the EBR-I1 and Dounreay Fast Reactors. The voids were uniformly distributed throughout the matrix. The amounts of helium gas produced by transmutation during these irradiations were less than one-tenth the amounts needed to balance the surface tension of the voids formed by the fast reactor irradiation. The fast reactor results are quite analogous to those reported here for the ETR irradiated steel. Electron microscope examination of the fast reactor irradiated material after a 1 hr postirradiation annealing at 900°C disclosed that essentially all the voids had been eliminated. The authors stated that the voids had developed due to the high concentration of vacancies produced during irradiatin., 6, ' The microstructure of the ETR irradiated material as-tested at 75O°C, Fig. 1, contained about 2 X lot5 cavities per cm3 with an average diameter of 110A. With the Van der Waals b correction and y = 1500 ergs per cm2, 300 ppm He would balance the surface tension of the observed cavities. Stereoscopic examination of the electron micrographs showed that the cavities were neither preferentially located near the grain boundaries nor highly concentrated at specific regions or precipitates. The cavities were nearly uniformly distributed throughout the matrix, on dislocations and at grain boundaries. These observations imply that the cavities were not the sole results of B'O

Jan 1, 1969

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year's symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. 'It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved') and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year's symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. 'It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved') and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By W. B. HILLHOUSE

AN excerpt from the Alabama State Mining Law, pertaining to, transporting men' into and out of the mines, reads as follows: "A trip of empty cars may be operated for the purpose of taking employees into and out of the mine, where the distance to and from their work exceeds one mile." The State Mining Department of Alabama includes in its inspection the transportation of men into and out of the mines, also studying and noting improvements, or progress made, that would tend to create a greater assurance of safety in this practice. Everyone is familiar with the original safety methods employed in man-trip transportation, such as passing a rope around the trip of cars, or through the cars, fastened in the conventional manner, and with the usual "clog," commonly called a drag, on the rear end. Also there is a more advanced method of transporting men, such as the double-rope system, which is feasible on slopes used exclusively for this purpose, and is very satisfactory. However, for the past eighteen months; the Republic Steel Corp. and the Tennessee Coal, Iron & Railroad Co. have adopted a practice that shows

Jan 1, 1935

By HENRY COLEMAN

WE as employees of these related companies, I am sure, are proud to be affiliated with them, and have great faith in the sagacity and fore- sightedness of our employers. Most of us here have been called into important positions in these organizations, and it should be our most earnest endeavor to sense and carry them out as if they were our very own. We have been asked to supervise and carry on a work over which our employers cannot personally watch. It has been well said that the most efficient organization is that which requires the least attention from its head. Because of the very nature and condition of our work, which separates us by many miles from our employers and makes it impossible for us to receive attention and instructions from the heads of our departments, save for occasional visits and correspondence, we are given a great opportunity to prove that we can be efficient workers without too much attention from the heads of our departments. There are few employees who cannot do their duty when it is laid before them in specific terms, and when their employers are always there to see that their plans are carried out. But the employee who is really giving efficient service sees his duty himself and willingly does it. '

Jan 1, 1931

By T. Lane Carter

BEFORE describing the experience with the Chinese on the Rand and the work they have accomplished, it will be necessary, sary, first, to give a brief account of labor-conditions in the Transvaal since the war, and then to show how the necessity of importation of labor arose. As is well known, the Transvaal mines are run on the dual system of labor-that is, the rough work is done by colored laborers under the superintendence of white men. From the start of mining operations in South Africa there has been the cry of shortness of native labor, due in great measure to the failure of Kaffirs to work continuously in the mines. While he works, the Kaffir is a satisfactory laborer, but his period of service is short, averaging about nine months. People unacquainted with the Kaffir have maintained that, by offering a higher wage and better accommodation, better results would be obtained from the native workers, but an increased wage simply aggravates the trouble. The Kaffir's wants are few. While at work he spends little of his money, and before long has sufficient capital with which to buy wives and become a gentleman of leisure. Doubling the wage of the Kaffir means that he acquires a competency in half the time, so that his period of service is correspondingly reduced. In 1899, before the war, there was always a cry about the scarcity of Kaffir labor. The highest number of natives at work was in July and August, 1899, when nearly 100,000 were employed. At the outbreak of hostilities the Kaffirs were scattered far and near, many doing well during the war by working for the military authorities. On the, resumption of mining operations on the Rand a serious mistake was made. Based on past experience, it was argued that if the whole industry decided to start anew with

Sep 1, 1908

By Lyon F. Terry

SPEED-UP of production of crude oil and its products, accompanied by rising prices and the organization of the industry on a war basis, featured the economic aspects of petroleum in 1941. Early in the year American tankers were urgently requested by the British to replace losses and offset slower transit under convoy. Some forty American owned tankers were first assigned to Britain and an additional forty-odd ships were transferred during the summer. This threatened to reduce our transportation facilities from Gulf ports to the Eastern seaboard below requirements, especially should sinkings have increased and the British needed more ships. Co-ordinator Ickes began preparations for restricting gasoline consumption in the Eastern district and plans were formulated for the construction of an emergency trunk pipe line from Texas to New York and Philadelphia refining centers, and for a gigantic tanker-building program. Sales of new oil-heating units in the East practically ceased. The companies were urged to transport as much oil as possible by tank car and by October 140,000 barrels of oil per day were reaching the East Coast district by rail, sufficient to meet 8 per cent of total requirements. But British sinkings from July through October decreased 63 per cent compared with the four months ended June 30, Britain began the return of tankers, the construction plans were dropped, and the threatened shortage was thus averted.

Jan 1, 1942

By J. G. Eberhort

ThE literature of surface phenomena shows that, except for most of the rare-earth elements, surface tensions have now been determined for almost every liquid metal. The situation for liquid metal oxides is, in contrast, characterized by a great scarcity of surface-tension data. A surface-tension correlation between these two classes of substances has been found which provides a means of estimating unknown liquid-oxide surface tensions from the corresponding known liquid-metal surface tension. Lf the surface tension of the liquid metal is a(M) and that of the liquid metal oxide is o(M,Oy), then oxides of all stoichiometries can be brought into one correlation if is plotted against with the surface tensions taken at the respective melting points. The available data is displayed in this fashion in Fig. 1 where the relationship between the surface tensions of the two classes of liquids is found to be The correlation in Fig. 1 is based on data found for nine liquid metal oxides and the corre- sponding liquid metals In cases where several sur-face-tension determinations were available on the same substance, higher values were generally favored over lower ones because they usually indicate greater Sample purity. All of the metal-metal oxide pairs are in good agreement with Eq. [I] except for B-Bz03. The reason for the departure of this pair from the correlation is not understood. To estimate the surface tension of other liquid metal oxides the corresponding liquid-metal surface tension must be found. A nearly complete bibliography of the surface tension of liauid elements is available in the 46th edition of the Handbook of Chemistry and physics. Some additional references on metals are included here for convenience Se,26Sr,'?ThanduZ5). It is also possible to estimate the surface tension of a solid metal oxide or metal from the corresponding liquid-state data. As a liquid material is cooled through its melting point the surface tension increases abruptly by an amount Ao. bondi' has estimated that the maximum value of Aa at the melting point is Ao = Ahf/A [2] where Alzf is the heat of fusion per atom and A is the area per atom in the interface. Thus with heat of fusion and crystallographic data the surface tension of a solid at the melting point can be estimated as o + Ao.

Jan 1, 1967

By Robert Livermore

It has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining CO. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining CO. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently fay from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, by means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities of ore, and made development in certain

Jan 1, 1915

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

DEFORMATION lines, also called etch markings or strain markings, are noneffaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries.1 Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrette to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation required for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted deformation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson' observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brick9 noted that deformation lines in 70-30 brass apparently associated with {111} planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards11 reported that in copper cold rolled less than about 50 pct few strain markings were apparent but for higher. reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass

Jan 1, 1948

By W. H. Hough, P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1943 resulted in the discovery of 11 new fields as compared with 12 discovered in the same area during I942. Of the 11 new fields, eight are classed as oil and/or condensate and three as gas fields. In addition to the new discoveries, several more or less important new horizons and extensions were encountered in some of the older fields, as noted in the text under the heading "New Pays and Extensions.'' Drilling During the year, 418 wells were drilled, as compared with 356 drilled during 1942. Of these, 323 were field wells, of which 188 produced oil, 21 were gas wells and 114 were dry holes. The remaining 95 viere wildcats, 12 of which produced oil, 4 produced gas and 79 dry holes. Distribution of themwildcats with respect to the various trends may be summarized as follows: over the 91,340,492 bbl. produced in the same area during 1942. The production statistics in the text and the accompanying tables include condensate or distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties all of the drilling and production" data applicable to this particular area. Outstanding Fields of 1943 The Upper Texas Gulf Coast covered in this report has 178 more or less active oil and gas fields, including the 1943 discoveries. Of these Table 4 lists those that were most important from the standpoint of production. Each of these fields pro duced in excess of one million barrels of oil during 1943. Some of the interesting facts to be noted from this list of some 26 oil fields are: (I) four of the fields— namely, Conroe, Hastings, Friendswood and Thompson—each produced more than 10 million barrels during 1943, whcrcas Conroe and Hastings were the only fields that produced 10 million barrels during 1942; (2) some of the older fields (discovered prior to 1920), such as Barbers Hill, West Columbia, and Hull, are still producing in excess of one million barrels annually; (3) some of the fields more than doubled their 1942 production—e.g., Anahuac and Friendswood. The large increase in production in practically all instances is the result of increased allowables from wells drilled prior to 1943 and

Jan 1, 1944

By W. H. Hough, P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1943 resulted in the discovery of 11 new fields as compared with 12 discovered in the same area during I942. Of the 11 new fields, eight are classed as oil and/or condensate and three as gas fields. In addition to the new discoveries, several more or less important new horizons and extensions were encountered in some of the older fields, as noted in the text under the heading "New Pays and Extensions.'' Drilling During the year, 418 wells were drilled, as compared with 356 drilled during 1942. Of these, 323 were field wells, of which 188 produced oil, 21 were gas wells and 114 were dry holes. The remaining 95 viere wildcats, 12 of which produced oil, 4 produced gas and 79 dry holes. Distribution of themwildcats with respect to the various trends may be summarized as follows: over the 91,340,492 bbl. produced in the same area during 1942. The production statistics in the text and the accompanying tables include condensate or distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties all of the drilling and production" data applicable to this particular area. Outstanding Fields of 1943 The Upper Texas Gulf Coast covered in this report has 178 more or less active oil and gas fields, including the 1943 discoveries. Of these Table 4 lists those that were most important from the standpoint of production. Each of these fields pro duced in excess of one million barrels of oil during 1943. Some of the interesting facts to be noted from this list of some 26 oil fields are: (I) four of the fields— namely, Conroe, Hastings, Friendswood and Thompson—each produced more than 10 million barrels during 1943, whcrcas Conroe and Hastings were the only fields that produced 10 million barrels during 1942; (2) some of the older fields (discovered prior to 1920), such as Barbers Hill, West Columbia, and Hull, are still producing in excess of one million barrels annually; (3) some of the fields more than doubled their 1942 production—e.g., Anahuac and Friendswood. The large increase in production in practically all instances is the result of increased allowables from wells drilled prior to 1943 and

Jan 1, 1944