Search Documents

By S. H. Williston

IT not often that bore hole surveys can be checked by actual. civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bis-bee, Ariz., drilled a 1245 ft, 8 in. diarn, churn drillhole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Because of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results of doubtful value. Sperry-Sun gyroscopic well-surveying instruments were finally used to locate the bottom of the hole. These instruments consist of a gyroscope to determine azimuth and either a pendulum or bubble inclino-meter. A multiple shot camera photographs both instruments on a single film and superimposes the photograph of a watch. Coordination of depth with time at the surface makes it possible to select the corresponding picture for any depth. After making several runs of the empty instrument housing from the top of the hole to the bottom to make sure there were no obstructions in the hole, three surveys on wire line were completed during the afternoon. The three surveys, in which readings were taken at different points in the hole on each survey, were computed and gave the following locations of the bottom of the hole in relation to the surface collar: survey No. 1—24.92 N, 30.30 W; survey No. 2—24.24 N, 31.11 W; survey No. 3—26.54 N, 27.72 W. Then the data from the three surveys were combined into a single set of calculations which gave a location for the bottom of the hole: combined surveys—24.27 N, 30.16 W. (Fig. 1.) Immediately upon the determination of the coordinates at the bottom of the hole, a drift on the 1300 ft level was started toward the indicated loca- tion some 38 ft northwest of the coordinates of the surface location, The bottom of the hole was located within the drift round in which it was expected, and the transit survey run to the actual location of the hole indicated N 27.18, W 29.71. This shows a discrepancy between the well survey and the transit survey of 0.45 ft in the westerly direction and 2.91 ft in the northerly direction. All surveys, both gyroscopic and transit, fell well within the width of an ordinary drift. While this is satisfactory for almost any and all mining requirements, a theoretical examination was made as to reasons for the discrepancy. A study of the course of the hole indicates that considerable right turn or spiral existed, and in all probability the surveying instrument was pulled out of alignment while traversing the turn by approximately 0.05 ft at the top and another 0.05 ft in the opposite direction at the bottom of the instrument. If such an allowance were to be made, the survey calculations would almost exactly correspond with those determined by transit. This sort of discrepancy would be minimized by the use of stabilizing guides. It is unfortunate that physical laws probably effectively prevent the use of gyroscopic instruments in EX and AX diamond drill holes. The directive power of a gyroscope falls off inversely at some rate between the third power and the sixth power of the diameter. Present instruments can be run in casing 53/4 in. ID or over and might be adapted to somewhat smaller diameters, but the difficulty of reducing these diameters to 11/4 in. or 2 in. is almost insurmountable at the present time. Acknowledgment The author wishes to express his appreciation to the Phelps-Dodge Corporation for permission to publish this article, and to the Operating and Engineering Departments for their cooperation on the survey; also to Donald Hering, of the Sperry-Sun Well Surveying Co., who actually made the survey and calculated the results.

Jan 1, 1951

By Paul C. Merritt

The story now unfolding on the Mesabi Range is more than just another chapter in the continuing history of iron mining. It is an epic of foresight, research and pioneering instinct just now culminating in the rapid growth of a new industry hardly more than ten years old. And that growth has been impressive. In the decade that has passed since Reserve Mining Co. blazed a trail as the first successful large- scale commercial taconite operation, the number of plants now existing or soon to be operating has grown to six. From Reserve's initial capacity of 3 million tons of pellets per year, total production capacity on the Range has surged to 31.5 million tons while capital investment has leaped from $300 million in 1955 to almost $1 billion today. During the past year alone, more than $500 million has been committed to these projects, an amount probably greater than that going into any other single mining area in the world. There is more yet to come.

Jan 10, 1965

By E. T. Turkdogan, J. H. Swisher

bi the fivst part of the paper results ave given on the rate of decarburization of Fe-C melts ln CO2-CO atmospheres at 1580°C. The rate -controlling step is believed to he that irvlloluing dissociation of curbotz dioxide on the suvfuce of the melt. 4 genevral reaction mechanistm is poslnlated jor gels-t11eta1 veactions oc-curit~g on the surface of iron coutcotamncited with chemi-sovbed osygesL. Oxygen the present work on decavbuvization of liquid iron and previous studies on the kinetics of nitrogen absorption and desorplion are discussed in terms of the postulated mechanism, ManY of the early studies of rate of decarburization of liquid steel were of an exploratory nature and laboratory exppriments carried out pertained to open-hearth or oxygen steelmaking processes. References to previous work on this subject may be found in a literature survey made by Ward. Using more sophisticated experimental techniques, several investigators have recently studied the kinetics of decarburization of molten Fe-C alloys in oxygen-bearing gases. For example, Baker et al2.' reported their findings on the rate of decarburization of liquid iron, levitated by an electromagnetic field, in carbon dioxide-carbon monoxide-helium atmospheres. In these levitation experiments the samples used were small in size, e.g., -0.6-cm-diam spheres weighing -0.7 g, and the rates were measured for decarburization from about 5 to 1 pct C at 1660°C. The rates obtained under their experimental conditions were considered to be controlled primarily by gaseous diffusion through the boundary layer at the surface of the levitated melt. Parlee and coworkers3 measured the rate of absorption of carbon monoxide in liquid iron. The rates were found to follow first-order reaction kinetics, yielding a reaction velocity or a mass transfer coefficient in the range 0.2 to 0.4 cm per min. The coefficient was found to decrease with increasing carbon content of the melt. These investigators attributed the observed rates to the transfer of carbon or oxygen through the diffusion boundary layer adjacent to the surface of the melt. In the work to be reported in this paper, an attempt has been made to study the kinetics of gas-metal surface reactions involved in the decarburization of liquid iron. EXPERIMENTAL The experiments consisted of melting 80-g samples from an Fe-1 pct C master alloy in an induction furnace and decarburizing in controlled CO2-CO mixtures at 1 atm pressure and 1580°C. The master alloy was prepared by adding graphite to electrolytic "Plastiron" melted in racuo. None of the impurities in the master alloy exceeded 0.005 pct. The reacting gases were dried by passage through columns of anhydrone; in addition, CO2 impurity in carbon monoxide was removed by passage through a column of ascarite. A schematic diagram of the apparatus is shown in Fig. 1. A 1.25-in.-diam recrys-tallized alumina crucible containing the sample was placed inside a 3-in.-diam quartz reaction tube, all of which was surrounded by an induction coil. A 450-kcps induction generator was used as the power source. Water-cooled brass flanges, which contained the gas inlet, gas exit, and sight port, were sealed to the top of the reaction tube with epoxy resin. The reacting gases were metered with capillary flowmeters and passed through a platinum wire-wound alumina preheating tube, 0.25 in. ID and 11 in. long. The gases were preheated to about 1300°C. A disappearing-filament optical pyrometer was used to measure the melt temperature. The pyrometer was initially calibrated against a Pt-6 pct Rh/Pt-30 pct Rh thermocouple. The temperature was controlled to within +10°C by manually adjusting the power input to the induction coil. In a typical experiment, an 80-g sample of the master alloy was melted in a CO2-CO atmosphere having pcO2/pco = 0.02 and flowing at 1 liter per min. A negligible amount of carbon was lost and no significant reduction of alumina from the crucible occurred during melting, e.g., 0.005 pct Al in the metal. After reaching the experimental temperature of 1580°C, the gas composition was changed to that desired for a particular series of decarburization experiments. The duration of the transient period for obtaining the desired gas composition at the surface of the melt was about 20 sec . The flow rate of the reacting gas was maintained at 1 liter per min. After a predetermined reaction time, the power to the furnace was turned off. During freezing, which took about 10 sec, the amount of gas evolution was not sufficient to result in a significant loss of carbon. The samples were analyzed for carbon by combustion and in a few cases they were analyzed for oxygen by the vacuum-fusion method. RESULTS A marked increase in the rate of decarburization of iron with increasing pcO2/pco ratio in the gas stream is demonstrated by the experimental results given in Figs. 2 and 3 for pco2/pco ratios from 0.033 to 4.0. In one series of experiments, denoted by filled triangles in Fig. 2, the reacting gas was diluted with argon (48 vol pct) resulting in a slower rate of decarburization. Samples from two series of experiments with pco2/pco = 0.033 and pco2/pco = 0.10 (with argon dilufion) were analyzed for oxygen. In these Samples the oxygen content increased with reaction time

Jan 1, 1968

By M. R. Geer

Coal washing assumed an important role in the mining industry of the Pacific Northwest long before washing practice became firmly established in the Appalachian field. A Scaife washer was operated in the state of Washington in 1887; and by 1927, the fist year for which complete statistics were compiled, nearly a third of the state's coal production was washed, in comparison with only about 5 pct for the country as a whole. Mechanical preparation was adopted in Alaska in 1922 in a plant constructed by the United States Navy at Chickaloon to provide bunker coal for naval forces operating in northern waters. Many of the coal beds mined in Washington and Alaska contained more impurities than those mined elsewhere, and this circumstance contributed to the early interest in mechanical cleaning. A much more important factor, however, was the inclination of the coal beds. With steeply pitching beds, hand sorting by the miner at the face is impossible; consequently, all material must be loaded and dealt with on the surface, just as is now proving the case with mechanical mining of flat beds. Thus "full-seam" mining afforded the same stimulus to the early development of coal washing in the Northwest that - it is providing under mechanization in the rest of the country today.

Jan 1, 1949

SAN FRANCISCO SECTION Roy H. ELLIOTT, Chairman - T. A. RICKARD, Vice-chairman W. H. SHOCKLEY, Secretary-Treasurer, 959 Waverley St., Palo Alto, Cal. D. A4. RIORDAN C. F. TOLMAN, JR. A joint meeting of the local sections of the several national engineering societies represented in San Francisco was held at the Engineers'. Club on Thursday evening, Sept. 26, 1918. The subject for the evening, "Fuel Conservation," was ably discussed by a-number of representatives of the Federal Administration and by engineers interested in the generation and utilization of all kinds of power on the Pacific Coast. The following extracts from papers presented at this meeting have been selected as being of the greatest interest and value to members of this Institute. Problems of the Fuel Administration ALBERT E. SCHWABACHER.-America's war needs call for 100,000,000 more tons of coal this year than in 1917, and 200,000,000 tons more than in 1914, when the war started, and this increase must come from a weaker man-power than that of 1917. It must be transported by a railroad system that has not been improved since the war started, and has been burdened with inconceivably greater demands than were made upon it before the war. This tremendous increased demand must be met by most intensive work in three directions; increased production, efficient conservation, and a distribution system which will insure against lost motion. While every European country has decreased its coal production since the war began, the United States has mined 50,000,000 tons more coal, during the first year of the war, and will increase this by another 50,000,000 the present year. Every 8 days there are being mined and transported as great a weight of coal as of the entire wheat crop of the United States. Of the 735,000,000 tons of coal which must be made available for consumption by our railroads, ships, war industries and people, 100,000,000 tons will come from the anthracite fields, the remainder from the bituminous fields. In 1917 there were produced about 330,000,000 bbl. of oil, and this year an additional amount over last year's production, of approximately 23,000,000 bbl. will be required. Water power developed 5,000,000 hp., the demand greatly exceeding the available supply.

Jan 12, 1918

In order to assist in the building up of the industries and commerce of France, by cooperating with the Congres General du Genie Civil, the four Founder Societies have appointed the following committee: E. G. Spilsbury and Arthur S. Dwight representing the American In-stitute of Mining and. Metallurgical Engineers; George F. Swain and Nelson P. Lewis to represent the American Society of Civil Engineers; Charles T. Main and George W. Fuller to represent the American Society of Mechanical Engineers; Lewis B. Stillwell and Andrew M. Hunt to represent the American. Institute of Electrical Engineers.

Jan 12, 1919

By N. Mungan, F. W. Smith, J. L. Thompson

Adsorption of polymers and transport, rheology and oil recovery efficiency of their solutions were studied in the laboratory to evaluate the use of polymers in waterflood-ing. While a tenfold mobility reduction was obtained with polymer concentrations as low as 0.05 per cent by weight, the mobility reduction depended on the type of polymer, molecular weight, salinity and pH of water, crude oil and capillary properties of the porous media. Choice of a suitable polymer and a workable concentration will have to be tailored for each application. Little reduction in the residual oil saturation can be expected from polymer flooding. Improvement in the volumetric sweep efficiency is possible hut the extent of the improvement can best be evaluated by properly designed field testing. Some aspects of the field use of polymer floods are discussed. INTRODUCTION Waterflooding is a simple, inexpensive secondary recovery method and is being used widely. Innumerable laboratory studies have been made to unravel the fundamentals of the displacement of oil by water and to find the ways of most efficient oil recovery. These studies and a great many field case histories have revealed that the prime cause of poor oil recovery is the inefficient and incomplete sweep of reservoir volume by the injected water. Sweep efficiency is affected by many factors of which the mobility ratio is an important one. Mobility ratio M is defined here as the ratio of water to oil mobilities: M = (k»/y,r)/(k,JJJJ........(1) In Eq. I, the permeabilities are the effective permeabilities and depend on fluid saturations and, hence, change during the different depletion stages in a flood. A wide practice is to use the effective water permeability at residual oil saturation and the effective oil permeability at interstitial water saturation in Eq. 1. If the mobility ratio is greater than one, the mobility ratio is unfavorable and water, being more mobile than oil, would finger through the oil zone resulting in poor oil recovery efficiency. If the mobility ratio is favorable (one or less) the displacement of oil by water occurs more or less in a pistonlike fashion. In some waterfloods. the mobility ratio is unfavorable and any additives by which the mobility of water can be decreased would favor more efficient oil recovery. The thing to bear in mind, however, is whether or not the improvement in oil recovery is sufficient to more than pay out the cost of the additives needed. For example, materials like sugars, alcohols and glycerine reduce water mobility by thickening the water, but the cost of material requirement precludes any field application. For an additive to be useful in water-flooding, it must bring about a large reduction in water mobility at low concentrations; it must be adsorbed only negligibly; and it must not completely plug up the formation. Some synthetic organic polymers have shown promise of meeting these requirements and have been used in the field.'-W owever, no in-depth studies of the rheological, adsorption and oil displacement characteristics of polymer solutions have been reported. The present work is a study of these properties. EXPERIMENTAL In this work, concentrations are given on a weight per volume basis; 0.5 per cent concentration means 0.5 gm of polymer is dissolved in enough water (or NaCl solution) to make 100 ml. A bactericide, usually 0.1 to 0.2 per cent by volume of 38 per cent formaldehyde solution, was used in the polymer solutions. The NaCl solution was 30,000 ppm. Some properties of the polymers studied are given in Table I. Physical properties of all cores used are in Table 2. Flow behavior of polymer solutions was studied by three consecutive flow tests in cores. First, water (or brine) was injected at constant rate of about 1 ft/D to obtain the water mobility. Then, filtered polymer solution (prepared in water or brine) was flowed through the core. Since the rate was constant, increase in the pressure drop across the core reflects decrease in the mobility. Finally, the core was flooded with water (or brine) to study recovery of mobility. The Alundum cores which were used in

Jan 1, 1967

By R. G. Davies

The activation energy for steady state creep above -500°C is observed to be independent of the applied stress although it varies from -67 kcal per mole at 2 at. pct Si to -100 kcal per mole at 11 at. pct Si due to changes in crystallographic order. The magnitude of the activation energy, by comparison with Fe-A1 alloys, indicates FeSi type of order in certain alloys. X-ray results confirmed the presence of FeSi type of order. It is proposed that dislocation climb is the rate controlling mechanism for all the alloys. It has been demonstrated that when a diffusion mechanism is the rate controlling process, the formation of a superlattice in brass,1 Fe3A1,2 Ni3Fe,3-5 and Feco6 1) increases the creep resistance, and 2) increases the activation energy for steady state creep. Furthermore, a study of creep in Fe-15 to 20 at. pct A1 alloys7 has revealed that as the alloy composition approaches the long-range order field, there is an increase in the activation energy for steady state creep which is thought to be due to an increase in short range order. Fe-A1 and Fe-Si alloys are similar in that they both form the DO3 superlattice in which aluminum or silicon atoms have only iron atoms as first and second nearest neighbors. There are, however, two important differences between the alloy systems: 1) The superlattice formation at -350°C commences at -10 at. pct si8 as compared to -20 at. pct Al,9 and 2) Fe-A1 alloys form a FeAl (B2 type) super-lattice where aluminum atoms have all iron first nearest neighbors even at 22 at. pct Al, but so far no similar FeSi superlattice has been observed. With the similarity between Fe-A1 and Fe-Si alloys in mind, alloys of iron with 2 to 11 at. pct Si were examined for variations with composition of the activation energy for steady state creep and of creep strength. The temperature range of greatest interest was above 1/2 TM (TM is the absolute melting temperature) where it is usually observed that diffusion is the rate controlling process. A subsidiary X-ray investigation of the Fe-Si system was undertaken in an attempt to define the position of the order-disorder boundary as a function of cooling rate. EXPERIMENTAL DETAILS a) Creep. Specimens whose gage length was 1.5 in. and with a cross-section 0.04 by 0.08 in. were strained in tension by a lever-arm arrangement, and the load was adjusted between each creep test to maintain constant stress. The apparatus and mode of operation have been fully described in a previous publication.7 As each test produced a creep strain of 0.25 pct, the variation in stress during the test was negligible. Creep strain was measured at the end of one of the alloy steel grips by a displacement transducer with the out-of-balance potential being recorded on a variable speed recorder. The full-scale deflection of the recorder could be varied in steps to give limits of sensitivity of between 0.1 and 0.001 pct creep strain. The alloys, Table I, were made available by the Metallurgical Department, National Physical Laboratory (N.P.L.), england,10 and by the Research Department, General Electric Co. (G.E.), Schenectady, N.Y. They were hot worked at -850°C, warm worked at 550° to 650°C, and recrystallized in vacuum at -750°C to give a grain diameter of -0.1 mm. All the alloys had a very low impurity content; those from the N.P.L., for which a complete analysis is available,&apos;&apos; show carbon less than 0.026 pct, manganese less than 0.006 pct, and oxygen plus nitrogen less than 0.0024 pct. b) X-ray Procedure. A General Electric XRD-5 X-ray set with a focussing lithium fluoride mono-chromator in the diffracted beam, and a pulse height analyzer to eliminate harmonic wavelengths of the cobalt radiation, was used to investigate the structure of several very fine grained (grain diameter <.01 mm) Fe-Si alloys after the following heat treatments: 1) Quenched from 700°C, 2) slow cooled from 650°C (-40°C per hr), and 3) very slowly cooled from 400° to 100°C (10°C per hr with a 24 hr anneal every 100°C). The method of obtaining the diffraction pattern over the range of 20 from 15 to 45 deg was to count for at least 100 sec every l/3 deg with a slit subtending 1 deg in 20 at the focus; the probable counting error was less than 2 pct.

Jan 1, 1963

By Nelson P. Hulst

COMMITTEES. DULUTH.-Nelson P. Hulst, Chairman; J. B. Adams, W. C. Agnew, M. H. Alworth, C. W. Andrews, R. Angst, William R. Appleby, C. E. Bailey, G. G. Barnum, E. F. Bradt, Mylie Bunnell, George L. Cheesebrough, Peter Christen¬sen, F. A. Cokefair, T. F. Cole, C. A. Congdon, N. Cowling, George H. Crosby, M. D. Cullum, C. d&apos;Autremont, Jr., H. L. Dresser, C. T. Fairbairn. Walter Fitch, F. L. Gilbert, J. T. Hale, G. G. Hartley, E. B. Hawkins, M. S. Hawkins, J. H. Hearding, Louis Hill, L. J. Hopkins, F. E. House, J. C. Hunter, 0. D. Kinney, J. W. Kreitter, E. J. Longyear, Alexander McDougal, W. A. McGonagle, A. M. Marshall, W. N. Merriam, T. D. Merrill, John Millan, P. Mitchell, Clarence Moore, Hon. Page Morris, C. H. Munger, Henry Nolte, W. J. Olcott, A. L. Ordean, Thomas Owens, F. A. Patrick, H. M. Peyton; D. M. Philbin, Capt. Charles Potter (U. S. A.), L. W. Powell, Harry Roberts, Louis Rouchleau, George A. St. Clair, J. U. Sebenius, Joseph Sellwood, Amos Shepherd, W. B. Silvey, George Spencer, George C. Stone, H. B. Sturtevant, George D. Swift, Kirby Thomas, C. D. Thompson, A. D. Thomson, G. A. Tomlinson, Charles Trezona, R. R. Trezona, Maj. J. H. Upham, Charles Van Barneveld, W. W. Walker, J. L. Washburn, A. C. Weirs, H. J. Wessinger, A. B. Wolvin, Dwight E. Woodbridge. HOUGHTON.-W. E. Parnall, Chairman; W. D. Calverley, Secretary; W. B. Anderson, L. S. Austin, Jacob Baer, William Bath, F. J. Bawden., Simon Beahan, John Been, C. H. Benedict, Walter Bloomfield, S. H. Brady, Samuel Brady, Henry Brett, A. L. Burgan, F. I. Cairns, W. H. Cake, Arthur L. Carnahan, William Carpenter, Phillip Carroll, John J. Case, T. L. Chadbourne, W. A. Childs, B. F. Chynoweth, Captain James Chynoweth, H. P. Clausen, F. G. Coggin, H. D. Conant, J. B. Cooper, J. R. Cooper, John Cuddihy, Thomas Cummings, Robert Davidson, J. B. Dee, J. R. Dee, T. S. Dee, Theodore Dengler, M. M. Dennis, Captain Thomas Dennis,. F. W. Denton, A. D. Edwards, R. M. Edwards, C. S. Fales, Daniel Fisher, Henry Fisher, James Fisher, A. L. Floeter, Frank H. Getchell, M. C. Getchell, W. M. Gibson, W. M. Gilliland, James G. Glanville, George Goodale, H. S. Goodell, A. R. Gray, Edward Grierson, Homer Guck, H. D. Haddock, Captain Josiah Hall, John L. Harris, Captain S. B. Har¬ris, Enos Harrold, F. William Hartmann, George L. Heath, C. M. Hoar, Thomas Hoatson, 0. P. Hood, Captain Thomas Hooper, Captain Joshua D. Husking, Dr. L. L. Hubbard, Arno Jaelinig, E. D. Johnson, G. A. Koenig, Edward Koepel, C. H. Krause, R. H. Leach, A. W. Leonard, James MacNaughton, Edward McCormick, Thomas McDonald, R. T. McKeever, F. W. McNair, James McRae, John Mackey, John C. Mann, Major G. A. Marr, Captain Thomas Maslin, Harry Mercer, James Merton, Michael Messner, William F. Miller, Captain J. Milligan, Dr. J. W. Moore, Charles H. Moss, H. F. Nickerson, Charles L. Noetzel, P. H. Paine, John Penrose, Captain John Pentecost, Graham Pope, R. C. Pryor, James Ramsay, J. T. Reeder, Allen F. Rees, J. H. Rice, W. G. Rice, James

Jan 1, 1905

Jan 1, 1963

By Charles Will Wright

Brief descriptions of the occurrence of the various deposits of strategic minerals then known in South America are published in "The Mineral Deposits of South America," by B. L. Miller and J. T. Singewald, 1919; in "Ores and Industry in South America," by H. F. Bain and T. T. Read, 1934; and in many publications on the individual countries. To give a gen.era1 idea of the situation today and possibilities for future output of strategic minerals in several of the countries, the following notes are offered. All tonnages are in metric units.

Jan 1, 1940

By P. E. Busby, C. Wells

FURTHER study of data used in determinations of 1—rates of diffusion of boron in austenite and 2—solubilities of boron in the a and phases of iron and steel&apos; has provided an equation for the diffusion of boron in a iron. In brief, the previously published data were accumulated from the results of deboron-izing (and decarburizing) experiments carried out in the range of 700° to 1300°C. Diffusion coefficients (D?) for boron in austenite were calculated using the Grube solution of Fick&apos;s law. However, only solubility values were estimated from the discontinuous concentration-penetration curves, Fig. 1, which are characteristic of diffusion in two phases. Dr. Carl Wagner&apos; has recently provided a solution for calculating D values from penetration curves of this type as follows: Cl1.1 —C8/C8- C11.1 = vp ? e ? erf (?) and D = ?/4?2 t where C11,12, C8, C11, and E have the values shown in Fig. 1. D is the diffusion coefficient, sq cm per sec; t is time of deboronizing anneal, see; and ? is a di-mensionless parameter. For a given diffusion experiment, the value of ? can be readily obtained by graphical solution from a plot of y vs the right-hand part of Eq. 1. D may then be evaluated from Eq. 2. The avplication of this solution to previously re-ported results, of which excerpts are given in Table I, permits the calculation of diffusion coefficients for boron in a iron. On the basis of these meager data, it is tentatively concluded that the diffusion of boron in a may be represented by the equation Da = 1011 e-92,900/RT where R is the gas constant, cal X 0C-1 X mol-1; and T is the absolute temperature, OK. Although the frequency factor, 106 sq cm per sec, is admittedly several orders of magnitude higher than expected, the value of Q, 62,000 cal per mol, appears reasonable and is, in fact, very similar to that for the self-diffusion of iron. It is pertinent to mention at this point that the value of Q obtained for the diffusion of boron in austenite by means of the Wagner solution is 19,000 cal per mol and is in excellent agreement with the value previously reported1 in the equation DT = 2xl0-3 e-21,000/RT [4] which was determined by the application of the Grube solution to other data. The fact that determined constants A and Q in the equation D? = A e-Q/RT were practically the same, independent of whether the Wagner or Grube solutions were used in determinations of D values, strengthened the authors&apos; belief that the computed values of D (Table I) using the Wagner solution are reliable. The relative values in Eqs. 3 and 4 for the diffusion of boron in the a and ? phases, respectively, suggest that boron forms a substitutional solid solution in a iron and an interstitial solid solution in ? iron. The same tentative conclusion has been reached by McBride et al.3 on the basis of relative solubilities, atom diameter, and the size of the interstitial hole in a and ? iron. In connection with the data for test 14 listed in Table I, it is of interest to calculate the solubility of boron in a iron using the D value given by Eq. 3. As might be anticipated from the small movement of the interface in test 14, proper substitutions in Eqs. 2 and 1 give a low value, approximately 0.0004 pct B, at 850°C. Apparently at 835°C (test 13) it is possible to obtain 0.0018 pct B, and at 850°C only 0.0004 pct B into solution in the a phase before a second phase appears. These observations are consistent with the Fe-B constitution diagram proposed by McBride, Spretnak, and Speiser.3 References P. E. Busby, M. E. Warga, and C. Wells: Diffusion and Solubility of Boron in Iron and Steel. Trans. AIME (1953) 197, p. 1463; Journal of Metals (November 1953). &apos;W. Jost: Diffusion in Solids, Liquids, Gases. (1952) pp. 69-71. New York. Academic Press Inc. "C. C. McBride, J. W. Spretnak, and R. Speiser: A Study of the Fe-Fe2B System. Trans. ASM (1954) 46, p. 499.

Jan 1, 1955

By H. Vincent Wallace

ALTHOUGH it is universally accepted that free oxygen is A necessary in a cyanide solution for the dissolution of gold and silver-in accordance with Elsner&apos;s equation that 2Au + 4KCN + 0 + H20 = 2KAu (CN), + 2KOH- little has been written and insufficient attention paid to the drop in extraction due apparently to loss of dissolved oxygen in mill solutions. Aeration or oxygenation of cyanide solutions has been more or less successfully accomplished by various types of agitators such as the Dorr (with or without air lifts), Pachuca tanks and more recently "Turbo-mixers" and Denver "Super- agitators"; also by the introduction of chemical oxidizing agents such as Solozone (Na,O,) . At the Wright-Hargreaves and other mines in the Kirkland Lake camp, the introduction of this reagent at the rate of about 1.25 oz. per ton of ore applied to the feed of the ball mills has certainly been beneficial.

Jan 1, 1932

By R. E. Salvoti

IN underground coal mining, the increasing trend towards mechanical methods is ever apparent. Figures for 1939 showed that 28 per cent of the total bituminous coal production was mined mechanically 1940 statistic will reveal an even higher figure. Factors causing this trend are varied, but the important are the following;

Jan 1, 1941

By R. J. Reynik, F. R. Meeks

IN the classical paper1 of Mehl and Rhines entitled "The Rates of Diffusion in the Alpha Solid Solutions of Copper", the authors state: "It has been mathematically demonstrated that the treatment of the data as though the diffusion were taking place between two flat plates instead of radially in a cylinder has no appreciable effect upon the results. Were the bars of a much smaller diameter, a modification of the analytical treatment would have been required." Unfortunately, the errors in the reported concentrations are much too large to neglect, as shown in the results below. A planar treatment of diffusion data assumes that the reference planes separated by a nominal distance (AX) have identical areas. An adjustment must be made on the concentration data should the successive diffusion planes differ in area. The Mehl-Rhines&apos; diffusion samples were cylindrical with copper electroplated onto copper-based alloys. Successive surface areas through which diffusion occurs are in the ratio ri/r1, where ri is the radial distance between the center of the sample and the center of the i th shell to which the host (alloy) atoms diffuse, and r1 is the radial distance between the center of the sample and the center of the innermost (i = 1) experimentally reported shell from which the alloy atoms diffuse. Hence, ri/r1 (i = 1, ..., n layers) is a dimensionless correction factor to be multiplied by the reported concentration data before planar-data analysis is attempted. In the forty-seven samples reported, the original interface between the copper alloys and the electroplated copper was located at a mean distance of 8.255 mm from the center of the samples. The successive layers, machined off the samples, were approximately 0.0762 mm thick. The distance (xi) at which concentration (ci) was reported was always a distance measured with respect to the original interface, that is, with respect to the fixed distance of 8.255 mm. Hence, the as yet undiscovered Kirkendall Effect was precompensated. The values of ri and r1 are therefore given by ri = 8.255 + xi and Y, = 8.255 + x,. The illustrative table below lists the position xi (mm), ri (mm), the value of ri/r1, the reported concentration (ci) in weight percent (only valid for radial analysis of data), and the corrected concentration [c&apos;i = (ri/r1)ci] in weight percent (only valid for planar analysis of data). Similar tables can be constructed for the remaining forty-six samples. The corrected data can be used to re-evaluate the diffusion coefficients for the reported systems.

Jan 1, 1965

CONTENTS PAGE BARTON, D. C.-The Eötvös Torsion Balance Method of mapping Geologic Structure (T. P. No. 50) 1 GEORGE, P. W.-Experiments with Eötvös Torsion Balance in the Tri-State Zinc and Lead District (T. P. No. 65). 15 LANCASTER-JONES, E.-The Computation of Eötvös Gravity Effects (T. P. No.75) HEILAND, C. A.-A Cartographic Correction for the Eötvös Torsion Balance-(T. P. No. 52) 17 SLICHTER; L. B.-Certain Aspects of Magnetic Surveying (T. P. No. 120). . . . 18 WEAVER, W.-Certain Applications of the Surface Potential Method (T. P. No.121) LUNDBERG, H.-Recent Results in Electrical Prospecting for Ore (T. P. No. 98). . 20 HOTCHKISS, W. 0., ROONEY, W. J. and FISHER, J.-Earth-resistivity Measure-ments in the Lake Superior Copper Country (T. P. No. 82) 21 LEONARDON, E. G. and KELLY, S. F.-Some Applications of Potential Methods to Structural Studies (T. P. No. 115) 23 MASON, M.-Geophysical Exploration for Ores (T. P. No. 45) 25 The Eötvös. Torsion Balance Method of Mapping Geologic Structure Discussion of the paper of D. C.. Barton, issued as Technical Publication No. 50 with Mining and, Metallurgy, February, 1928. D. C. BARTON.-The field surveys which I have been privileged to use as illustrations for this paper were done for Mr. DeGolyer&apos;s companies and were released through his favor. W. J. MILLARD, Tulsa, Okla.-Has any oil been found by the torsion balance in West Texas? D. C. BARTON.-NO new oilfield has been discovered on the basis of torsion balance work. It has had some part in controlling the policy of certain companies in playing the extension of known oil fields. A number of "T. B." structures have been drilled and dry holes obtained. Of those known to the writer, one apparently was a structural high, one is a broad general high but locally low and probably is a deep-seated structural high, one seems normal although the control is poor, and one was considered structurally low but is now suspected by some geologists of being structurally high. E. L. DEGOLYER, New York, N. Y.-A large gravity structure, generally referred to, I believe, as the Crosby County Structure, has been found in West Texas. This structure is perfectly symmetrical with the arrows all pointing toward a common center, very much like the Nash salt-dome pattern in Dr. Barton&apos;s paper (Fig. 9). One of the peculiar things about it, from the standpoint of the gravity high, is that it is so

Jan 1, 1928

By Charles E. Locke

DEPRESSION in all lines of the mineral industry except gold, which began in 1930 and continued, even worse, through 1931, had its effect on ore concentration. Construction was limited to the completion of plants already begun. Every possible economy was adopted. Changes and improvements involving expense were postponed. Research was largely abandoned. Operations became highly efficient and costs were cut down, although this did not necessarily mean a lower cost per ton because of the greatly reduced capacity at which mills were run. Lower metal prices caused the operators to seek the optimum ratio of concentration and grade of concentrates looking toward maximum economic recovery; that is, net profit. In the crushing field no marked changes occurred. The Symons cone crusher for intermediate work is in use almost everywhere. Its manufacturers claim that 900 machines have been installed in 21 countries, replacing two previous steps of crushing and yielding a product sufficiently fine to form a satisfactory feed for rod mills and ball mills. A new Telsmith crusher has appeared which has curved jaws something like the Symons cone and consequently the same advantage as the latter.

Jan 1, 1932

By Ferdinand S. Ruttmann

There is now in use at the mines of the Chateaugay Ore and Iron Co., at Lyon Mountain, New York, an ore-concentrating machine or jig, which, in view of the increasing attention given to the subject of concentrating lean ores of iron, seems worthy of notice. This Conkling Jig, as it is called, is not entirely unknown, having been used at several places with more or less success; but as yet, I believe, no drawings of it or records of its work have found a place in print. Although the jig will be found to be merely an adaptation of old forms, there are several points which deserve attention, particularly the method of central discharge, of freeing the bearings from grit, and the rotation of the sieve or screen. The ore-body at Lyon Mountain consists of a bed of rather compact, granular magnetite, occurring in a gueiss formation. The side walls of the ore-body are not sharply defined, the ore 011 either side becoming gradually poorer as the distance from the central point of the body increases. It is this lean ore, which, before the introduction of the jigs, was thrown away as waste, that is now concentrated. The material treated conseqnently consists of magnetite, intermixed with the component parts of gneiss, viz. quartz, felspar, hornblende, and mica. Grains of trap also form part of this material. These come from dykes of trap, which cross the ore-body at intervals. The ore which is to be concentrated usually contains from 30 to 40 per cent. of metallic iron. It is first crushed to the size of two inches, or less, by two large Blake crushers. The material from these crushers passes by a shute lined with screens, having holes 2 inches in diameter, to a second set of four crushers, set so as to close to one inch. The product from this set of crushers, together with that which passes through the screens in the shute, is then taken by an elevator to the top of the mill, and passed through a revolving screen, perforated with ) inch holes. The ore which passes through the screen goes to the jig-hoppers ; that which passes over goes to a third

Jan 1, 1888

By Thomas T., Read

IT is difficult to judge how much influence the success attained during its first year, 1864-65, by the School of Mines at Columbia had on developments in education for the mineral industry elsewhere in the immediately subsequent years. The facts are as follows: 1. The Massachusetts Institute of Technology began giving instruction in February 1865, with a mining course included in its curriculum. 2. Early in 1865 the faculty of the Department of Science, Literature and the Arts of the University of Michigan requested permission from the Regents to establish "a course of study to be called the School of Mines . . . Also that the degree of Mining Engineering, be conferred on students who should complete the course of study prescribed in the same." A resolution authorizing this was adopted by the Regents on March 28, 1865. 3. Samuel Hooper endowed a Sturgis-Hooper professorship of geology at Harvard in 1865 with the intention of making it a nucleus of a new School of Practical Mining and Geology. 4. Yale appointed Alfred P. Rockwell professor of mining in 1865. 5. Lafayette College appointed Henry S. Osborn professor of mining and metallurgy in 1865. 6. Washington College (as Washington and Lee was then known), rising out of the ashes of Civil War destruction, made a fresh start in 1865, with Generalized as its president, and offered a mining course in the first catalogue thereafter published. 7. Lehigh University, founded in 1866, had a mining curriculum from its beginning. 8. Rensselaer Polytechnic began offering a curriculum in mining and metallurgical engineering in 1867. It would be natural to suppose that these events were a reaction, to the success of the school at Columbia, - and possibly they

Jan 1, 1941

By T. F. Witherbee

THE following calculation of heat requirement covers the working of the furnace from January 25th to February 14th, inclusive. A short time previous to the first date the furnace had been working rather badly, so that 300 lbs. of ore and 500 lbs. of limestone were taken off. Within the time mentioned the quality of the iron passed

Jan 1, 1877