Search Documents

By Zay, Jeffries

THE effect of thoria (ThO2) on grain growth in tungsten was discussed in some detail in a paper presented before this Institute by one, of the authors in 1918.1 In that paper it " was assumed that the, thoria was present in the tungsten entirely as a mechanical mixture. There was no indication in the experiments described that even a trace of the thoria was in solid solution in the tungsten. Langmuir,2 however, observed that thoriated-tungsten filaments under certain conditions showed electron emissions many thousand times greater than unthoriated tungsten at the same temperature. He concluded from his studies that a slight amount of the thoria had dissociated on heating the filament to a temperature near 220°. C. At this temperature and higher, part of the thorium diffuses to the surface of the filament where it evaporates at. a much faster rate relatively, than the tungsten, and also at a rate, nearly as fast as it is brought to the surface by diffusion: If the temperature is lowered to say 1800°,. C., diffusion of the thorium atoms to the surface is more rapid than evaporation, sown adsorbed film of thorium atoms is produced on the surface of the tungsten filament. The electron emission is governed by the outside layer of atoms so the emission from such a filament might be expected to approxi¬mate that of a thorium filament at the same temperature. PRESENCE OF METALLIC THORIUM IN THORIATED TUNGSTEN If the filament containing the adsorbed film of thorium. is heated to a sufficiently high temperature, the thorium atoms evaporate: rapidly and the electron emission becomes more nearly that of tungsten. On cooling again to 1800° C., or thereabouts, the emission 'builds up gradually to a maximum. The filament containing the adsorbed layer of thorium atoms is said to be "activated." By studying the rates of activation under different conditions of prior thermal treatment and at different temperatures, Langmuir was able to arrive at an estimate of the

Jan 1, 1927

By George W. Friesen

This paper presents the historical trend and de- fines the causes of drilling cost escalation in the Gulf of Mexico during the 1970's. The three major components of escalation are: 1) inflation, 2) supply-demand imbalance (demand pull) and 3) decreases in drilling efficiency. The decade was divided into three periods. During each period one component of escalation was responsible for most of the rise in costs. From 1970 through 1973 only inflation pushed costs upward. During 1974 and 1975 a supply- demand imbalance caused most of the escalation. Since 1975, decreases in drilling efficiency have produced the major component of escalation. During any one year or period of years, the sum of the three components will give the total escalation rate. The reasons why different components contribute more toward escalation during certain years than others are shown by following the timing of oil and gas price increases, the overall quality of the acreage offered each year in offshore lease sales and the resulting drilling activity.

Jan 1, 1982

||Abad, Leopoldo F., Min Engr, Div of Mines, Bureau of Science Manila, P I '23 Abadilla, Quirico A, Geol, Lago Pet Corp Box 172, Maracaibo, Venezuela '20 ||Abbey, Robert Graham, The W W Sly Mfg Co Train Ave, Cleveland, Ohio '21 Abbott, A. N., Mines Supt, Mazapil Copper Co, Ltd Concepcion del Oro, Mexico '23 Abbott, Clarence E., Mgr, Mines & Quarries, Tenn Coal, Iron & R R Co, 1242 Brown Marx Bldg, Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr , Consolidation Coal Co , Elkhorn Div Jenkins, Ky. '16 Abbott, Robert R., Met Engr , Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz. '23 Abeel, George H, Jr., Cons Min Engr 4612 West 17th St , Los Angeles, Cal '18 Abel, Albert E., Asst to Pres, Valley Mould & Iron Corp Sharpsville, Pa. '19 Abernathy, George Elmer, Prof of Geol & Min , Kansas State Teachers College, Pittsburg, Kans. '20 Abey, Hiroshi, Min & Met Engr, Min & Met Dept, The Higher Technical School, Osaka, Japan. '17 ||d'Ablaing, Philip R, Chem , Anaconda Copper Min Co Great Falls, Mont '25 Aborn, Robert H , Research Assoc., Mass Inst of Tech Cambridge, Mass '19 Abouchar, Sylvain Sley, Min. Engi & Geol , care of S H Sekaly, 13 Rue El Nimr, Cairo, Egypt '17

Jan 1, 1923

By Joseph Newton

MUCH the same story can be told about the copper industry for the year 1944 as for the three preceding years. Operators report few or no technical changes at their plants and the main endeavor has been to maintain high production with existing equipment. No large new installations have been made to increase plant capacities and apparently over-all copper production has passed its maximum. The present decline in copper production results partly from the severe labor shortage. As is true of most industries; the outstanding fact about the copper industry during the past few years has been its tremendous and sustained production which has been maintained in spite of serious shortages in material. labor, and technical personnel. The figures in Table I give a concrete example of how production has been increased at one large smelter in the United States-the Garfield plant of the American Smelting and Refining Co. at Garfield. Utah. These figures, reported by W. G. Rouillard. superintendent. give the production of the Garfield plant for the five years 1940-44 inclusive. The total blister production

Jan 1, 1945

By AIME AIME

TRANSFER to the Bureau of Mines of the responsibility for conservation and production of helium, and announcement that a proposal has been made to the President for commercial operation of the Los Angeles has attracted new attention to the helium program of the Government. The matter is one in which mining engineers, and the mining industry in general, have a peculiar interest. Helium is a byproduct of the petroleum and natural gas industry. It is found in certain of the natural gases which have themselves been discovered, in the main, in the search for oil. If it is to be produced on a large scale, the conservation and development of the fields will necessarily be done by the men of the oil and gas industry. There is no known or expected source of supply of quantities of commercial importance save in the natural gas fields. Not all gas wells supply helium and none of them supply it in important percentages. If it were necessary to prospect a field, develop it, lay pipe lines and build production plants for the helium alone, the cost would be prohibitive. On that basis helium would necessarily be restricted to essential war uses, where cost is subordinate to need. As a byproduct of the natural gas in certain, at least, of the fields in the United States there is distinct reason for anticipating that it may be produced in amounts and at a cost that will permit its regular use in commercial airships.

Jan 1, 1925

By I. L. Dillamore

I. L. Dillamore (University of Birmingham)—The different textures developed in various fcc metals have long awaited satisfactory explanation and it has now become clear that these differences are related to parallel differences in the deformation characteristics of the metals. Liu is correct, therefore, in seeking to account for the observed textures in terms of the flow mechanisms but I believe, for the reasons outlined below, that the particular interpretation of flow mechanisms proposed by Liu is open to substantial objections. By considering the forty-eight possible designations of the twelve octahedral slip systems found in fcc metals as distinct and separate deformation modes, Liu has fallen into the error of assuming that only positive glide dislocations associated with each system are present. In fact both positive and negative dislocations will be present and the only difference between for instance the systems B4 and B4' (in Liu's notation) is that under a stress of given sign the direction of motion of a dislocation is reversed on changing from B4 to B4'. For both orientations positive and negative dislocations will be present. In considering possible dislocation interactions it is, therefore, inadmissible to differentiate between R4 and R4' as Liu does. Liu considers those dislocation interactions which give the biggest reduction in energy to be the most favorable and neglects, on the grounds that they will form strong barriers to slip, interactions between dislocations with perpendicular Burgers vectors. Setting aside interactions between positive and negative dislocations of the same slip system, which must occur regardless of the combination of slip systems chosen, the biggest reduction in energy occurs for the Lomer-Cottrell interaction and it is Lomer-Cottrell barriers which are thought to provide the stronger dislocation obstacles. On the other hand the intersection of dislocations with perpendicular Burgers vectors is thought to be a low-energy process which contributes only a fairly small temperature-dependent part of the total work hardening. On this basis it seems doubtful whether the reduction in energy through possible dislocation interactions provides a reasonable criterion for choosing the operative slip systems. From the point of view of texture development it is unsatisfactory to ignore the slip rotations leading to an end position and to neglect to consider the stability of the chosen end point. It is also unsatisfactory to treat the two stress axes as interchangeable since, if the stress system is idealized as biaxial, one stress is compressive and the other is tensile. For the same reason the rotations of the two stress axes are not made compatible simply by assuming that the same slip directions are responsible for the rotations of the two stress axes. It is, in short, essential to treat the two stress axes as acting together on the same slip systems. Turning to the question of the difference between the copper-type and the brass-type texture, there now remains little doubt that the difference is attributable to differences in stacking-fault energy (y), as noted by Liu, but it is doubtful whether the temperature dependence of the texture in copper and in silver is due to increasing stacking-fault energy with increasing temperature. The results of Swann and Nutting42 cited by Liu were obtained in Cu-A1 alloys and the apparent increase in stacking-fault energy on raising the temperature may be influenced by short-range ordering. In pure metals such effects are absent and the only data available on the variation of y with temperature are those of Buhler et a1.43 for silver. They report a minimum at 200°C which does not fit the hypothesis put forward by Liu. It is much more likely that thermal activation of cross slip is important in determining which texture develops, as proposed by Dillamore and tors. These workers have proposed an explanation for the differences in observed texture among the fcc metals and the pole figures predicted consist of an orientation spread which is in better agreement with observation than the limited number of discrete orientations suggested by Liu. The theory of Dillamore and Roberts is also able to account for the differences between aluminum and copper which Liu still leaves unexplained. Y. C. Liu (author's veply)—The writer appreciates the interest of Dr. Dillamore, but must discuss some of his comments in order to avoid cross purposes. The phrase, "forty-eight slip systems," which appeared twice in the text—in the caption of Fig. 1 and the first paragraph in the Discussion—might unfortunately have led Dr. Dillamore to disagree

Jan 1, 1965

By T. F. Witherbee

IT is proposed to give, first, a description of the works ; second, a report of the first six months of the present blast; and third, such improvements as have been suggested by the practical working. The site selected for this furnace was, at the time of commencing work, October, 1872, entirely covered by the navigable waters of Lake Champlain. A coffer-dam was first built of cribs of round timber filled with stone, forming three sides, while the shore answered for the fourth. Considerable excavating was done with a steam-dredge, a hole being left for it to pass out. The opening was then built up, and the cribbing banked up with blue clay from the bottom of the lake, to render it water-tight and the dam pumped out; the remainder of the excavating being done by hand. All of the foundations, with the exception of the elevator-tower, and fifteen feet of the east side of hot blast, rest on the Potsdam sandstone, which forms the shore line, dipping into the lake at an angle of fifteen degrees. Owing to jogs in the formation, a much greater depth was found necessary than was at first anticipated, the foundation under the stack

Jan 1, 1876

HAVING taught you to make aqua fortis and to cleanse and reduce it to perfection, before I teach you the work of parting on a large scale, I wish now to teach you how to make an assay of the amount of gold present in a quantity of silver, so that you may proceed to your work with open eyes in order to become aware of mistakes when you have erred yourself or have been deceived by someone else. Therefore it is necessary to know very exactly, before you take it out, how much gold should be in your cucurbits from the weight of the silver that you put in. Thus you may see the gain or loss, if you had to deliver it to someone else or if you had bought it. If you did not do this you would proceed blindly in your work.

Jan 1, 1942

26. G. H. S. Price, S. V. Williams, and G. J.O. Garrard: Heavy alloy, its production. properties and uses. Metal Industry (1941) 599 354s 372. 394. 27. R. Kieffer and W. Hotop: p. 320 of ref 12. 28. F. R. Hensel. E. I. Larsen, and E. F. Swazy: Physical properties of metal compositions with a refractory metal base. Chap. 42, 483, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 29. R. Kieffer and W. Hotop: p. 290 of ref. 12. 30. H. Freundlich: Kapillarchemie. 211 (1923) Leipzig. 31. W. Ostwald: Zisch. f. Phys. Chemie. (1900) 34, 503. 32. G. A. Hulett: Zisch. f. Phys. Chemie. (1901) 37. 385; and (1904) 47, 357. 33. J C. Chaston: Discussion to Price, Smithells and Williams, p. 257 of ref. 4. 34. W. Dawihl: Untersuchungen ueber die Vorgaenge bei der Abnuetzung von Hartmetallwerkzeugen. Ztsch. f. techn. Phys. (1940) 21 336. 35. W. Dawihl and J. Hinnueber: Ueber den Aufbau der Hartmetallegierungen. Kol-loidzlsch. (1943) 104, 233. 36. F. Skaupy: Dispersoidchemische und verwandte Gesichtspunkte bei Sinter-hartmetallen. Kolloidzlsch. (1942) 98, 92; and (1943) 102, 269. 37. F. C. Kellcy: Cemented tantalum car- bide tools. Trans. ASST (1932) 19, 233. 38. E. W. Engle: Cemented carbides. Chap. 39, 436, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 39. W. Dawihl: Zlsch. f. Melallkunde. (1940) 32, 320. 40. P. M. McKenna: Tool Materials (Ce- mented Carbides). Chap. 40. 454. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 41. G. A. Meerson. G. L. Sverev, B. Y. Osinovskaja: Zhurnal Prikladnoi Khimii. (1930) 139 66. 42. A. G. Metcalfe: The mutual solid solubility of Tunesten Carbide and Titanium carbide- Metal Trealmenl (1946) 13, 127. 43. P. Schwarzkopf: Powder Metallurgy. 196-201 and 354-356 (1947) New York. 44. H. Burden: The manipulation and sintering of hard-metals. Special Rep. No. 38, p. 78. Iron and Steel Inst.. 1947. London. 45. W. D. Jones: Principles of powder metal- lurgy. 150. (1937) London. 46. J. E. Drapeau: Sintering of powdered copper-tin mixtures. Chap. 32. 332, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 47. H. E. Hall: Sintering of copper and tin powder. Metals and Alloys (1939) 10, 297. 48. F. Sauerwald: Present status of powder metallurgy. -.Melallwirlschafl. (1941) 20, 649. 671. 49. H. L. Wain: Powder metallurgy; influence of some processing variables on the properties of sintered bronze. Report ACA-25. Australian Council for Aeronautics (1946) Melbourne. 50. S. L. Hoyt: Constitution of copper-tin alloys. Metals Handhook, 1364. (1939) Cleveland. 51. T. Ishikawa: Studies on the interdiffusion of copper, tin and graphite powders. Nippon Kinzoku Gakkai-Si (1937) I, 226. 52. A. Carter and A. G. Metcalfe. The struc- ture of porous bronze bearings. Special Rep. No. 38, p. 99. Iron and Stecl Inst. (1947) London. 53. R. P. Koehring: Sintering atmospheres for production purposes. Chap. 25, 278. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 54. C. G. Goetzel: Some properties of sintcred and hotpressed copper tin compacts. Trans. AIME (1945) 161, 569. 55. J. W. Lennox: The production of some non ferrous engineering components by powder metallurgy. Special Rep. No. 38. p. 174. Iron and Steel Inst., 1947, London. . P. Duwez and H. E. Martens: The power metallurgy of porous metals and alloys having a controlled porosity. TP 2343, Metals Tech. April 1948. This volume. p. 848. 57. E. A. Owen and L. Pickup: X-ray study of the interdiffusion of copper and zinc. Proc. Royal Soc., London, Series A. (1935) 149, 283. 58. C. G. Goetzel: Sintered and hotpressed compacts of copper-zinc powder. Chap. 34. 352, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 98, R. Chadwick. E. R. Broadfield, and S. F. Pugh: Observations on the pressing. sintering, and properties of iron-copper powder mixtures. Special Rep. No. 38, p. 151, Iron and Steel Inst. (1947) London. 60. A. Squire: The properties of iron-copper compacts. Watertown Arsenal Lab. Rep. WAL No. 67101. 61. F. C. Kelley: Properties of sintered iron- comer uowder. Iron Age (Aug. 15. 193) 158 57. 62. G. H. Howe: Sinterinn of Alnico. Iron Age (Jan. 11. 1940) 14.5, 27. 63. R. Kieffer and W. Hotop: p. 359 of ref. 12. 64. W. Hotop: Permanent magnets from sintered iron-nickel-aluminum. Stahl und Eisen (1941) 61, 1105. 65. P. R. Kalischer: Some experiments in the production of aluminum-nickel-iron alloys by powder metallurgy. Trans. AIME (1941) 145, 369. 66. S. J. Garvin: Production of sintered per- manent magnets. Special Rep. NO. 38. p. 67. Iron and Steel Inst. 1947, London. 67. F. C. Kelley: Discussion to P. R. Kalischer. p. 375 of ref. 65. 68. R. Kieffer and W. Hotop: p. 357 of ret, 12. 69. C. H. Howe: Sintered alnico. Chapter 48, 530, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. Powder Metallurgy Seminar (C. G. Goetzel presiding) C. G. Goetzel—The seminar has been opened by a man who has been active in the field for over fourteen years and has made, since then, some major contributions to the advancement of the art. After having been associated with the Moraine Products Division of General Motors Corporation for over ten

Jan 1, 1949

By Carl Zapffe

THE object of the Bradley process is to free manganese oxide from its associated gangue and separate the contained iron oxide by dissolving the manganese and precipitating it from the solution. 'The fundamental features of the process are : making. both 1 a manganese ore and an iron ore; effecting a separation of manganese .and. iron by means of selective roasting; leaching- the manganese from the roasted ore by using ' ammonium sulfate; precipitating the manganese by using the ammonia gas generated during leaching; fixing the precipitate by oxidizing with air; breaking down and reforming the ammonium sulfate, so that daily very little additional ammonium sulfate beyond that originally charged into the system is required; washing the manganese precipitate and the iron-silica residue and evaporating the liquor to conserve the dissolved salts in the moistures of these two products and 'to reduce the sulfur content,; drying the precipitates; magnetic wet-concentration of the iron-silica residue; sinteriny the manganese-and .the' iron-concentrates.

Jan 1, 1929

By J. B. Campbell, V. V. Valleroy, B. T. Willman, L. W. Powers

A steam drive of heavy oil was field tested in a shallow, low oil-saturation formation near Deerfield, Mo. The pilot was conducted in the Warner formation, a sandstone containing an 18' API oil having 1,000-cp viscosity at the 60F origind reservoir temperature. The formation war at a depth of 160 ft. Steam was injected into nine input wells arranged in an array of inverted five-spot patterns. In the completely confined center pattern, 14 temperature observation wells were installed to obtain thermal data and observe test progress. Late in the test, slugs of ammonia were injected to trace the flow paths of injected fluids. From the test area about 7,000 bbl of oil were produced. Data were obtained on areal and vertical temperature distribution, steam front advance, reservoir fluid movement and terminal saturations. This field test of a steam drive (I) demonstrated the feasibility of the method, (2) confirmed that the low residual oil saturations observed in the laboratory are obtained in the steam-swept region in the field and (3) provided recovery and conformance data for one set of field conditions. INTRODUCTION The Deerfield steam drive pilot test was conducted in a shallow sandstone containing 1,000-cp oil. The venture was undertaken cooperatively by the research and production departments of Carter Oil Co., which organizations have since been consolidated into Esso Production Research Co. and Humble Oil & Refining Co.. respectively. The production department was interested in steam injection at Deerfield because it appeared to be the most promising method of commercially producing this heavy oil deposit. The research department was interested in applying the new recovery method and in evaluating its performance in the field. At the time the test was begun, the initial oil saturation was not well known. Subsequent air coring and early pilot results confirmed that there was too little oil in place for profitable commercial exploitation by steam. Pilot termination at that time, however, would have been premature for evaluating field performance of the process, and the tert was continued to obtain additional data on steam injection as a recovery method. The test was located in Vernon County, Mo., about 10 miles north of the town of Deerfield and only a few miles from the Kansas border. The pilot site was selected as typical of the area. The location represented neither the highest nor the lowest oil saturation region in the acreage under lease in 1954. The steam drive was conducted in the Warner sandstone of Lower Pennsylvanian age. At the test site the top of the Warner occurs at about 160 ft subsurface and the formation is a fine- to medium-grained micaceous sandstone that dips gently to the northwest at the rate of 12 to 15 ft/ mile. A cross-section and permeability profile of the test location are shown in Fig. 1. At the pilot location the average total thickness of the Warner formation is about 43 ft, but the effective thickness for steam drive is 26 ft. Two distinct types of hydrocarbon saturation are apparent. The lower portion of the total sand, averaging about 17 ft thick, contains a very heavy asphaltic material that will not flow under the influence of a steam drive. This bottom interval, referred to as a dead oil residue, was not considered as part of the net sand undergoing steam exploitation. The initial formation and fluid properties of the upper 26 ft in the test area are summarized in Table 1, and variation of oil viscosity with temperature is shown in Fig. 2. Imbibition tests on preserved core samples taken at the end of the pilot test showed that the Warner sandstone was then neutral or slightly water-wet. Initially, the reservoir may have been strongly water-wet as indicated by low relative permeability to water during both water injection testing and early steam injection. PRIOR HISTORY Initial production tests of wells at the pilot site produced water with only a faint show of oil. No gas was produced except at Well 7-W in the pilot area and at another well about 1/3 mile northeast of the pilot. Prior to the start of the steam drive, a two-well water injection test and a two-well air injection test were conducted. No oil was produced by either. Water was pumped into Well I-W in the northeast corner of the pilot area with simultaneous production from Well 1 (Fig. 3). The air-injection tat was run at input Well 9-W and its offset, Well 2, in the southwest corner. Air and water injectivities were about the same when corrected for viscosity and pressure differences.

pAbad, Leopoldo F., Min, Engr,, Div. of Mines, Bureau of Science Manila, P. 1. '23 Abadilla, Quirico A,, Geol., Lago Pet. Corp Box 172, Maracaibo, Venezuela, '20 Abbey, Robert Graham, The W. W. Sly Mfg, Co Train Ave., Cleveland, Ohio. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd Concepcion del Oro, Mexico, '28 Abbott, Clarence E., Mgr., Mines & Quarries, Tenn, Coal, Iron & R. R, Co,, 1242 Brown Marx Bldg,, Birmingham, Ala. '04]

Jan 1, 1928

By James E. York

AT a meeting of the American Society for Testing Materials at Atlantic City, June, 1908, Dr.. C. B. Dudley, in his presidential address,' showed the vital necessity of not only making a steel rail as good as in the past, but of making it considerably better in order to meet the present and prospective require¬ments of railroads. Doctor Dudley requested the co-operation of all who from personal experience could give information that would result in bringing about the production of a steel rail that could be relied upon to meet the present requirements. I have had considerable experience in the practical manufacture of steel of almost every grade, during the past 40 years, and I shall suggest changes that will bring about the results desired. Doctor Dudley has had a long experience as chemical and metallurgical expert for the Pennsylvania railroad, but he frankly admits that up to the present time both he and other metallurgical experts lack the practical knowledge of steel-making that is necessary to state correctly the reasons for the unreliability of the steel rails now produced. The necessity is self-evident for more positive practical knowledge on the part of these experts of what is possible and what is impossible regarding the practical manufacturing of steel rails from the ingot to the, finished product. Chemical knowledge in steel-making is far in advance of what it was years ago, and might be said to cover every requirement (in that department) for producing reliable steel. The study of the metallography of steel has been of great value, also the physical testing of steel, but this knowledge will only de-

May 1, 1909

By L. R. Smith

BUTANE OPERATED drilling rigs are a recent innovation in the petroleum industry, so extensive data on their operation are not available. However, experience indicates that, within limitations, as much can he accomplished with butane as with steam, at a decided reduction .in expense of installation and cost of operation. Commercial butane is a liquid motor fuel similar to gasoline, but much more volatile, so that it has to be stored under pressure. At 10° F. it is liquid at atmospheric pressure, but at 100° it has a pressure of 70 lb. or more. As soon as the pressure is reduced, it turns to vapor and in that state is far more easily mixed with the air necessary for combustion. Butane occurs as a by-product in the absorption process of natural gasoline extraction from casing-head gas. The product has been used to some extent 10 raise the octane value of gasoline. However, because of its volatile nature, such admixture is stable only to a limited degree. Attempts also have been made to introduce the product in a gaseous form into oil- hearing formations in repressuring work. It has, however, until recently, for the most part been wasted.

Jan 1, 1937

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The a-p type alloys are subject to a loss of tensile ductility with increasing hydrogen content. No hydride phase is visible in embrittled a-B type alloys. The embrittlement encountered appeared to be of the strain-aging type. Both compositional and structural factors are shown to influence the hydrogen tolerance of a-B type alloys. IN previous papers by the authors, the effects of hydrogen on the structure and mechanical properties of high-purity and commercial-purity titanium were described. It was shown that the presence of hydrogen in these materials results in a hydride phase having low solubility at room temperature. This insoluble phase had little effect on the room temperature tensile properties, but did decrease the notch-bar toughness to a large degree. The binary Ti-H systemz indicates that hydrogen is much more soluble in £ than in a-titanium. Hence, it is not expected that the embrittling effects of hydrogen in a-fi alloys will be similar to that found in a alloys. Materials of this type studied in the present investigation included two commercial a-/3 alloys, Ti-8Mn and Ti-4A1-4Mn; three high-purity Ti-Mn alloys containing 3, 6, and 9 pct Mn; and four high-purity Ti-Mo alloys, Ti-SMo, Ti-10.9M0, Ti-13.1 M0, and Ti-20M0, of the a-B and B types. Materials and Fabrication—The high-purity base alloys, composed of iodide titanium and high-purity metals, were prepared by double arc melting under argon in a water-cooled copper crucible, using a water-cooled tungsten electrode. Radiographic examination showed homogeneous Ti-Mo alloys. The analyses of the alloys used in this investigation and their as-fabricated hydrogen content, where determined, are listed in Table I. The two commercial alloys were 1/2 and % in. diam bar stock. No analyses other than hydrogen content were made. In order to maintain the a-B relationship existing in the two commercial alloys, vacuum annealing and hydrogenation were carried out in the B field prior to final fabrication. Fabrication then was done by The three high-purity Ti-Mn alloys were forged to 3/4 in. diam rods at 1600°F, and hot swaged to 1/2 in. diam at 1380°F. Machined and degreased bar stock was vacuum annealed or hydrogenated, fabricated to 1/8 in. diam rod by hot swaging, annealed in argon for 1 hr at 1380°F !75O°C), and water quenched. The six yz lb Ti-Mo ingots were forged to Wi in. diam rods at 1600°F and then hot swaged to % in. diam. Machined and degreased specimens were vacuum annealed or hydrogenated in the /3 field, prior to fabrication, by swaging to Y4 in. rod at 1400°F. After fabrication, the 5 and 10.9 pct Mo alloys were annealed in argon for 16 hr at 1290°F and water quenched to give equiaxed a-B structures. The higher molybdenum content alloys were argon annealed 4 hr at 1470°F and water quenched to give all £ structures.

Jan 1, 1957

By A. H. Duane, A. E. Miller

The high-temperature allotropy of some heavy rare-earth metals and their alloying behavior with magnesium in the 0 to 50 at. pct Mg region was studied by thermal, microscopic, and X-ray methods. Examination of a hcc phase retained upon quenching alloys of different magnesium content confirmed the existence of a bcc high-temperature allotrope in pure gadolinium, terbium, dysprosium, holmium, erbium, thulium, and lutetium. The lattice constants of the pure metals were determined from a Vegard's Law extrapolation and .found to be 4.05, 4.02, 3.98, 3.96, 3.94, 3.92, and 3.90 + 0.02 A, respectively. In all of the systems studied, the high-temperature bcc phase decomposed eutec-toidally, when slowly cooled, into a hexagonal rare earth-Mg solid solution and a simple-cubic peritec-tic AB-type compound. In 1956, Spedding et al.' observed high-temperature resistivity anomalies in the light rare-earth metals and made several unsuccessful attempts to retain the high-temperature form of these materials at room temperature by quenching the pure metals from temperatures near their melting points. High-temperature X-ray techniques were used by Spedding et a1.' in 1959, to investigate the high-temperature allotropy of the rare-earth metals. This study showed that lanthanum, cerium, praseodymium, neodymium, ytterbium, and possibly gadolinium are bcc at temperatures near their melting points. Discontinuous changes in resistivity at elevated temperatures were also observed for pure gadolinium, terbium, dysprosium, holmium, and lutetium, thus indicating the possible existence of a high-temperature crystalline transformation in these metals. However, due to experimental difficulties encountered in the high-temperature X-ray analysis of these metals, their allotropic form was not identified. Spedding et a~.~ in 1960 observed that yttrium displayed a continuous solid solubility with lanthanum at elevated temperatures, thus showing the high-temperature structure of yttrium to be the same as that of lanthanum, i.e., bcc. Similarly, the high-temperature alloying behavior of gadolinium with yttrium showed gadolinium to be bcc at elevated temperatures. The bcc nature of the high-temperature form of yttrium was again recognized in 1960 by Eash and carlson4 in their study of the alloying behavior of yttrium with thorium. Gibson and Carlson, in a similar study of the alloying behavior of yttrium with magnesium, found that by quenching Y-Mg alloys from within the 0-solid solution region, Fig. l, they were able to retain the allotropic form of yttrium. It was the present authors' intention to use this method to show the existence of a bcc high-temperature form of the heavy rare-earth metals gadolinium, terbium, dysprosium, holmium, erbium, thulium, and lutetium. Simultaneous with the present work, Beaudry and Daane' have shown the bcc nature of the high-temperature form of scandium. EXPERIMENTAL PROCEDURES Materials. The rare-earth metals used in this study were prepared by the calcium reduction of the fluoride and were further purified by vacuum distillation. The magnesium was obtained from the New England Lime Co. and was also purified by distillation prior to its use in the preparation of the rare earth-Mg alloys. The results of chemical and spec-

Jan 1, 1964

By A. H. Rhoades, D. T. King, R. J. Gray

Tests and methods of detecting oxidized coal are studied. Particular emphasis is placed on the microscopically discernible changes that accompany the chemical and physical changes affecting the technological properties of coal during oxidation. Coal samples were used from the low-volatile Pocahontas No. 3 Seam, McDowell County, W.V., and from the high-volatile Cedar Grove Seam, Mingo County, W.V. Tests conducted include: carbonization, free-swelling index, phase inversion, froth flotation, Gieseler plasticity, oxygen by difference and by neutron activation, volatile matter, pH of coal slurries, alkali solubility, and electrostatic charge.

Jan 1, 1977

By W. M. Lehrer

RECENT development of high-temperature brazing alloys has required information regarding the eutec-tic temperature and composition of the Pd-rich section of the Pd-B system.. Literature on this subject was found to be scanty with no complete system yet determined. Buddery and welch1 report an inter-metallic compound occurring in the Pd-B system at 6.33 wt pct B (PdsBz). Another source, Sieverts and Bruning,2 indicates that after annealing at 700°C, a 1.6 and a 2.0 wt pct B alloy were two phase whereas a 0.75 pct B alloy was single phase. Recent work3 using a hot-stage microscope has proposed a eutectic temperature of 743OC. This method utilized the observation of the onset of incipient melting at grain boundaries. The eutectic composition, however, was not determined. METHODS AND PR0CEDURES Five alloys were prepared by triple inert arc-melting high-purity palladium (95.98 pct) with additions of 2 to 6 pct purified amorphous boron. The alloys were crushed within a hardened steel mortar with a steel pestle. The 2 pct alloy, however, was too tough to be crushed in the above manner so was crushed by successive reductions through a rolling mill. Approximately 17 to 18 g of the crushed alloy was used in the thermal analysis. The alloys were melted in pure quartz crucibles. The thermocouple protection tubes were also of quartz and fused along the inside wall of crucibles to prevent floating of the thermocouple. This was an expediency as centering of the thermocouple in the melt would have been preferable. Melting was done in a tube furnace with a slow flow of tank helium maintained as a protective atmosphere. Heating and cooling rates were maintained at 3.5OC per min through the critical temperature ranges by means of a synchronous motor hook-up to a furnace controller. All specimens were heated to 100°C over the indicated liquidus on heating prior to reversing to the cooling cycle. Specimens emerged from the furnace with mirrorlike brightness attesting to the protective quality of the helium atmosphere. Thermal arrests were detected by the differential thermocouple technique using chrome l-alumel couples and nickel as the reference specimen. Arrests were recorded on a Leeds-Northrup automatic X-Y recorder. The specimen temperature and temperature difference were read to + 7.5OC and ± 1.5OC, respectively. These readings were well within the sensitivity of the instrument amplifier. Chromel-alumel couples were used in lieu of Pt-Rh as very few arrests were contemplated in excess of 1200" to 1300°C, the approach of instability. No standardization was performed on these thermocouples subsequent to their use. RESULTS The thermal arrest temperatures obtained are plotted in Fig. 1 as a function of wt pct B. The composition function was obtained by chemical analysis of portions of the specimens after the thermal analysis was completed. The 2 to 6 pct nominal alloys were found to have 1.80, 2.35, 3.65, 4.18 and 5.90

Jan 1, 1960

By Leon Borgman, Michael P. Lipkewich

Orebodies at or near the surface are generally amenable to open pit mining. The development of a mining program involves designing an ultimate pit and a production schedule. This pit maximizes total profit while the production schedule maximize6 the present value of the property. Optimum pit limits can be approximated by two-and three-dimensional numerical techniques. These techniques presuppose that the mineralized area has been sufficiently sampled to allow a reasonably accurate prediction of grade at any spatial location.

Jan 1, 1969

By Joseph Daniels

(San Francisco Meeting, October, 1911.) I. THE FRITZ ENGINEERING LABORATORY. TEE Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. . The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem, and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight, 84 ft. long and 9 ft. wide, in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section, containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Feb 1, 1912