Search Documents

By R. H. Wightman

THE following paper describes current mining practices of the Riverside Cement Co. at its Crestmore plant, Riverside, California. For a number of years the Riverside Cement Co. obtained its raw materials by surface quarry operations but after these deposits were exhausted for equipment available at that time, the company started underground mining. Mine workings were begun in 1927 to 1930 for the recovery of limestone by block-caving methods. GEOLOGY The bed of limestone that is being worked is a metamorphosed and recrystallized limestone, which is generally white in color and from medium to coarsely crystalline. This bed is fissured by water courses that vary from minute cracks to large areas. The bed has also been cracked by intrusions along the footwall and hanging wall. These walls are coarse-grained, gray, quartz granodiorite. The strike of the deposit is north and south and it dips to the east at an angle of approximately 50º. The bed is approximately 1700 ft. long, 270 ft. thick at right angles to the dip at the middle of the deposit and tapers to a thickness of approximately 100 ft. at each end. MINING METHODS The mine layout consists of four main levels with elevations as follows: 892 Collar of shaft. 800 Manway level used for ventilation, prospect purposes and as an entrance into the stopes. 700 Mining level where all material is extracted and on which are located the tapping grizzlies. This is the elevation from which all main cutoff stopes and undercutting work is started. 660 Haulage level where the limestone is drawn from transfer raises into the cars and is transported to the tipple by electric locomotives. 633 Level where all water is collected and which keeps the general water table below the working levels. A detailed description of the mine was given in U. S. Bureau of Mines Information Circular No. 6795, in June 1934. Current Block Development The first blocks to be caved were developed very much after the procedure followed in the copper mines of Arizona. This paper covers the ninth block to be caved. With a hard, tough rock like our limestone, it was found that some alterations in the development and control of draw in caving were necessary to secure better crushing effect and provide more safety for such secondary blasting as is required. Sequence of Block Development I. The fringes of the 800-ft. manway level are driven to confirm the diamond drill information and serve to determine the final location and development required for the block (Fig. I).

Jan 1, 1944

By Arnold Hague

At the Buffalo meeting, October, 1888, Dr. Raymond presented a paper entitled: "Soaping Geysers" (p. 449 of the present volume), in which he called attention to the use of soap by tourists to cause eruptions of several of the well-known geysers in the Yellowstone Park. Incorporated in this paper appears a communication received from me, written from camp in the Park, in reply to some inquiries on the subject. The letter discussed somewhat briefly the means employed by visitors to the Park to hasten the eruptions from hot springs and reservoirs of hot water, which remain dormant for days, or even weeks or months, at a temperature near the boiling-point, without any display of geyser-action. As the paper has called forth considerable comment, I desire to elucidate one or two points in relation to the temperature of the springs, and to answer some inquiries about the composition of the thermal waters. In the summer of 1885, a Chinaman, employed as a laundryman for the accommodation of the tourists at the Upper Geyser Basin, accidently discovered, much to bis amazement, that soap thrown into the spring from which he was accustomed to draw his supply of water produced an eruption in every way similar to the actual workings of a geyser. Tourists with limited time at their command, who had travelled thousands of miles to look upon the wonders of the Yellowstone, soon fell into the way of coaxing the laundryman's spring into action, to partly compensate them for their sore disappointment in witnessing only the periodical eruptions of Old Faithful. Successful attempts upon this spring soon led to various endeavors to accelerate action in the dormant and more famous geysers. In a short time, so popular became the desire to stimulate geysers in this way, that the Park authorities were compelled to enforce rigidly the rule against throwing objects of any kind into the springs. In connection with a thorough investigation of the thermal waters of the Yellowstone Park and the phenomena of the geysers, I undertook a number of experiments to ascertain the action of soap upon the waters and to determine, if possible, those physical conditions of various pools and reservoirs which permitted the hastening of an

Jan 1, 1889

By John Lamont, Walter Crafts

The principle formulated by Grossmannl for calculating hardenability of steel by multiplying the ideal diameter of "pure" iron-carbon alloys by factors for grain size and alloying elements has been confirmed on many steels and has proved useful in designing substitute alloy steels. Grossmann found that the typical behavior of the multiplying factors was to increase directly in proportion to the amount of the alloy present in a steel. However, the multiplying factor for the effect of silicon on hardenability was found by Grossmann to increase to a lesser degree as the amount of silicon was increased. In view of the increasing use of silicon in heat-treating steels, the effect of silicon on hardenability is becoming more important. Calculation of the hardenability of high-silicon steels made at the Union Carbide and Carbon Research Laboratories, Inc., indicated that the multiplying factor for silicon increased directly in proportion to the amount of silicon present. A more extended study of high-silicon steels covering fairly wide ranges of grain size, carbon, manganese, and aluminum has confirmed that up to 2 per cent silicon the multiplying factor is directly proportional to the silicon content. Manganese and aluminum factors have also been! determined. The results of the study offer strong confirmation of the general validity of Grossmann's multiplying principle. Testing Procedure Steels on which the study of the effect of silicon on hardenability was based were made in high-frequency induction furnaces using Armco iron and standard alloying materials. The ingots were forged to bars, and sections were normalized prior to machining Jominy hardenability test specimens. The Jominy test was carried out under standard conditions.2 The depth of hardness penetration for determination of ideal diameter at "half hardness" was taken at the hardness level indicated in Fig. 29 in Grossmann's paper by the solid line for 50 per cent martensite in plain carbon steel. The depth of penetration of hardness on the Jominy specimen was converted to ideal diameter by the relation given in Fig. 28 of Grossmann's paper. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Aluminum was determined as "acid-soluble aluminum" rather than as total aluminum, as it is probably more representative of the aluminum that is effective as an alloying agent. In addition to the elements nominally present in the steels, analyses were made for residual phosphorus, sulphur, nickel, copper, molybdenum and chromium on one heat of those made with the same materials during the same period. Actual grain size was determined by microscopic examination of small samples quenched in water after receiving the same thermal cycle as the Jominy hardenability specimens. Chemical analyses, heat-treatment, grain size, and hardenability are shown in Table I representing three ranges of composition.

Jan 1, 1943

By Shiou-Chuan Sun, R. E. Zimmerman

An evaluation of the mechanism surrounding the froth flotation of coarse coal and mineral particles as a result of experiments conducted at The Pennsylvania State College. Maximum size ranges for both bituminous and anthracite coals were established as well as the factors affecting the floating of coarse particles. CONSIDERABLE interest is developing in the froth flotation of coal and the maximum particle sizes which can be treated by such method. The economic necessity of recovering extreme coal fines and slurries plus the restrictions being placed upon stream pollution have brought about many new and prospective installations of flotation plants. Most coal slurries or silts have a wide size range, some sizes of which may be unsuitable for effective froth flotation. This fact also enters into the froth flotation of other minerals and the principles that SHIOU-CHUAN SUN and R. E. ZIMMERMAN, Members AIME, are Assistant Professor and Division Chief, respectively, Division of Mineral Preparation, The Pennsylvania State College, State College, Pa. Joint AIME-ASME Fuels Conference, French Lick, October 1949. TP 2843 F. Disccussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Sept. 12, 1949. apply to coal would also apply to minerals in general. A series of experiments were made by the authors for the purpose of investigating factors influencing the froth flotation of coarse mineral particles and an attempt has been made to evaluate those factors. This paper presents the results of a study of the froth flotation of coal particles in the size range greater than 35 mesh. During the study a "multi-bubble" hypothesis has been developed to explain the various phenomena observed in the behavior of coarse particles in froth flotation of coal. The terms coarse, intermediate, and fine particles as used in this paper are arbitrary and differ for various minerals. For coal alone the term intermediate particles means that the particle size is within the range of 35 and 200 mesh of Tyler sieve sizes. Sizes of coal particles coarser and finer than this size range are termed respectively as coarse and fine particles. Methods of Conducting Flotation Experiments: All of the flotation tests, except those shown in table 1, were carried out in a laboratory Fagergren flotation machine, using 300-a samples of solids for each test. All mineral samples we; prepared from selected lumps of high purity by crushing, grinding, and screening to the desired sizes. Except coals, all the other samples were cleaned through magnetic

Jan 1, 1951

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35OF and 1350F. Results are accurate to the seventh decimal place. IN the course of investigations of the thermal properties of various rocks proposed for use as aggregates in concrete structures, a relatively rapid method of determining coefficients of linear thermal expansion was required. A method which proved to be satisfactory for this purpose was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss. The method is based on the fact that strain effects in a specimen can be determined by measuring variations in the resistance of an electrical conductor firmly cemented to the surface of the specimen. Equipment for the determination of strain, electrically, has been developed by the Baldwin-South-wark Division of the Baldwin Locomotive Works in Philadelphia. This equipment includes small strain gauges made of coils of resistance wire bonded between thin sheets of paper (SR-4 gauges), and a portable "Strain Indicator" which records variations in the length of the gauges in microinches per inch. Gauges of this type are now in general use for determinations of various mechanically-induced strains, but their use for the determination of coefficients of thermal expansion appears to be a new application. The advantages of the method are that the test specimens may be relatively small and require only a minor amount of preparation, that a large number of tests can be run at the same time, and that the installation and operation of the equipment is relatively simple. The method and equipment described are now in regular use for determining the coefficients of linear thermal expansion of rock samples submitted to this laboratory. Rocks which have been tested include granites, syenites, gabbros, and other igneous rocks, limestones and dolomitic limestones, sandstones, and quartzites. Specimen Preparation: To standardize the conditions of the tests, the rock specimens are sliced by diamond saw into slabs about 11/2x11/4 in. In the case of bedded or foliated rocks, three oriented slabs are cut from the same specimen, and represent, respectively, a direction in a plane of the bedding or foliation of the rock; a direction along the bedding or foliation and at a right angle to the first; and a direction across the planes of bedding or foliation. One of the large surfaces of each slab is lapped for a few minutes with No. 100 abrasive powder to remove saw scars and irregularities. The slabs are soaked in petroleum ether and then dried in an oven to remove all traces of oil picked up in the sawing

Jan 1, 1951

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in ' Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in term of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L slope of energy grade line by s Mass per unit volume of solids by m. Mass Per unit volume of liquid by mi Mass per unit volume of mixture by mm We then have as an expression for the solids load: W = pQmm The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1948

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35OF and 1350F. Results are accurate to the seventh decimal place. IN the course of investigations of the thermal properties of various rocks proposed for use as aggregates in concrete structures, a relatively rapid method of determining coefficients of linear thermal expansion was required. A method which proved to be satisfactory for this purpose was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss. The method is based on the fact that strain effects in a specimen can be determined by measuring variations in the resistance of an electrical conductor firmly cemented to the surface of the specimen. Equipment for the determination of strain, electrically, has been developed by the Baldwin-South-wark Division of the Baldwin Locomotive Works in Philadelphia. This equipment includes small strain gauges made of coils of resistance wire bonded between thin sheets of paper (SR-4 gauges), and a portable "Strain Indicator" which records variations in the length of the gauges in microinches per inch. Gauges of this type are now in general use for determinations of various mechanically-induced strains, but their use for the determination of coefficients of thermal expansion appears to be a new application. The advantages of the method are that the test specimens may be relatively small and require only a minor amount of preparation, that a large number of tests can be run at the same time, and that the installation and operation of the equipment is relatively simple. The method and equipment described are now in regular use for determining the coefficients of linear thermal expansion of rock samples submitted to this laboratory. Rocks which have been tested include granites, syenites, gabbros, and other igneous rocks, limestones and dolomitic limestones, sandstones, and quartzites. Specimen Preparation: To standardize the conditions of the tests, the rock specimens are sliced by diamond saw into slabs about 11/2x11/4 in. In the case of bedded or foliated rocks, three oriented slabs are cut from the same specimen, and represent, respectively, a direction in a plane of the bedding or foliation of the rock; a direction along the bedding or foliation and at a right angle to the first; and a direction across the planes of bedding or foliation. One of the large surfaces of each slab is lapped for a few minutes with No. 100 abrasive powder to remove saw scars and irregularities. The slabs are soaked in petroleum ether and then dried in an oven to remove all traces of oil picked up in the sawing

Jan 1, 1951

The income of the Institute is derived from dues, subscriptions to Mining and Metallurgy and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes, It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization and at a minimum of expense. J. V. W. Reynders is chairman of the Endowment Committee. Seeley W. Mudd Memorial Fund THE Seeley W. Mudd Memorial Fund, consisting of $100,000, was given the Institute in 1929 by the family of Colonel Mudd who had served the Institute as Director, Vice-president and on many important committees. His long career of distinguished professional and public service is fittingly commemorated by this fund. The income is available for support of research and other special purposes. In view of Colonel Mudd's life work with the nonferrous metals and his keen interest in the younger men of the profession it is purposed to apply the fund particularly to the benefit of these two. Control of income is exercised by the Board of Directors on recommendation of a Committee consisting of the President and Secretary, ex officiis, together with three others selected by the Board. The Committee consists at present of the following members: W. H. Bassett, President; H. Foster Bain, Secretary; Harvey S. Mudd serving until October, 1931; Edgar Rickard serving till October, 1932; George Otis Smith serving until October, 1933. On recommendation of this Committee the Board has authorized as a first project the preparation of a series of small books designed especially to be helpful to the Junior Members. These are now being written and it is hoped will be available for distribution in 1931. The list includes: A Brief History of American Mining, by T. A. Rickard; Mining Costs, Why and What, by Arthur Notman; Introduction to Mineral Economics, by H. Foster Bain and T. T. Read; Choice of Methods—A Record of Experience in Making Decisions, with chapters by W. H. Bassett, F. W. Bradley, E. DeGolyer, Howard N. Eavenson, A. B. Parsons, J. V. W. Reynders, L. D. Ricketts, Robert E. Tally, Pope Yeatman and others. One other book is projected but final selection has not been made. The purpose of these books is to afford the younger men who now come into a highly specialized profession some substitute for the broad

Jan 1, 1930

By R. A. Falconer, H. L. Lovell

With increasing requirements for fine coal cleaning and the many advantages of the cyclone operating on a coal-water slurry, a series of studies designed to achieve an enhanced understanding of the cyclone parameters has been pursued. The purpose of this investigation has been to vary a series of dimensional parameters with an experimental 15-in. diam hydro-cyclone, and to determine the relative effects of parameter variations upon ash and sulfur removal. This study of the hydrocyclone is a continuation of a series of investigations, conducted in the Dept. of Mineral preparation at The Pennsylvania State University, which are directed toward the removal of ash and sulfur constituents from fine bituminous coal by size-density separations in cyclones, and toward a fuller understanding of the complex mechanisms involved in such separations. The purpose of this investigation has been to vary a series of dimensional parameters with an experimental 15-in. diam hydrocyclone, and to determine the relative effects of parameter variations upon ash and sulfur removal. Of special interest was the response to cone angle variation, since it is the high included cone angle that generally distinguishes the hydrocyclone as a gravity separator rather than a classifier. DESCRIPTION OF THE HYDROCYCLONE Fig. 1 is a dimensional drawing of the hydrocyclone used in the investigation. The unit was designed and fabricated by Heyl and Patterson, Inc., for experimental use. The dimensional parameters considered were: 1) Three cone sections having included angles of 45, 60, and 95,degrees, 2) Three 3 1/8 in. diam vortex finders having lengths of 15, 17, and 19 1/2 in., 3) Three 4 1/16 in. diam vortex finders having lengths of 15, 17, and 19 1/2 in. 4) Two apex sections having diameters of 2 and 2 1/4 in. The feed inlet orifice had a fixed diameter of 3 in. The hydrocyclone test installation was made at The Pennsylvania State University pilot plant at Barnes-boro, Pa., which operated at 50 tph. During the period that the hydrocyclone was tested, research was in progress at the Barnesboro site to reprocess refuse material from a near-by coal preparation plant in

Jan 1, 1968

By Albert E. Reed

THE development of the modern high-speed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1945

By John Lamont, Walter Crafts

The principle formulated by Grossmannl for calculating hardenability of steel by multiplying the ideal diameter of "pure" iron-carbon alloys by factors for grain size and alloying elements has been confirmed on many steels and has proved useful in designing substitute alloy steels. Grossmann found that the typical behavior of the multiplying factors was to increase directly in proportion to the amount of the alloy present in a steel. However, the multiplying factor for the effect of silicon on hardenability was found by Grossmann to increase to a lesser degree as the amount of silicon was increased. In view of the increasing use of silicon in heat-treating steels, the effect of silicon on hardenability is becoming more important. Calculation of the hardenability of high-silicon steels made at the Union Carbide and Carbon Research Laboratories, Inc., indicated that the multiplying factor for silicon increased directly in proportion to the amount of silicon present. A more extended study of high-silicon steels covering fairly wide ranges of grain size, carbon, manganese, and aluminum has confirmed that up to 2 per cent silicon the multiplying factor is directly proportional to the silicon content. Manganese and aluminum factors have also been! determined. The results of the study offer strong confirmation of the general validity of Grossmann's multiplying principle. Testing Procedure Steels on which the study of the effect of silicon on hardenability was based were made in high-frequency induction furnaces using Armco iron and standard alloying materials. The ingots were forged to bars, and sections were normalized prior to machining Jominy hardenability test specimens. The Jominy test was carried out under standard conditions.2 The depth of hardness penetration for determination of ideal diameter at "half hardness" was taken at the hardness level indicated in Fig. 29 in Grossmann's paper by the solid line for 50 per cent martensite in plain carbon steel. The depth of penetration of hardness on the Jominy specimen was converted to ideal diameter by the relation given in Fig. 28 of Grossmann's paper. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Aluminum was determined as "acid-soluble aluminum" rather than as total aluminum, as it is probably more representative of the aluminum that is effective as an alloying agent. In addition to the elements nominally present in the steels, analyses were made for residual phosphorus, sulphur, nickel, copper, molybdenum and chromium on one heat of those made with the same materials during the same period. Actual grain size was determined by microscopic examination of small samples quenched in water after receiving the same thermal cycle as the Jominy hardenability specimens. Chemical analyses, heat-treatment, grain size, and hardenability are shown in Table I representing three ranges of composition.

Jan 1, 1943

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in ' Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in term of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L slope of energy grade line by s Mass per unit volume of solids by m. Mass Per unit volume of liquid by mi Mass per unit volume of mixture by mm We then have as an expression for the solids load: W = pQmm The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1948

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By E. H. Crabtree, Neil S. Parker

THE custom milling plant of the Eagle-Picher Mining and Smelting Co. is at Sahuarita, Arizona, approximately 20 miles south of Tucson. It is connected by a 2-mile railroad spur to the main line of the Southern Pacific Railroad between Tucson and Nogales. The capacity of the plant is 500 tons per day. The mill is conventional except perhaps in the rather wide variety of ores treated. These vary from straight copper ores, from which only one concentrate is produced, and lead-zinc or copper-zinc ores from which two concentrates are produced, to complex gold-silver-copper-lead-zinc ores, which require the simultaneous production of three or four concentrates. Custom ores are received in lots varying in size from a few truckloads to several carloads. Similar ores, after crushing and sampling, may be commingled, or individual lots may be milled individually. The ores are first dumped either into one of two 200-ton railroad bins, or into one of the two 75-ton truck bins. From these bins the lot of ore is individually crushed in a 24 by 16-in. jaw crusher to 3-in. size, and then to 1/2-in. size in a 3-ft Symons shorthead crusher. After crushing to 1/2-in., the ore is conveyed to the automatic sampling plant. This consists of three Vezin samplers in series, each successively cutting out 10 pct, to pct and 5 pct of its feed. After No. 1 sampler, the material passes through a mixing barrel and is then crushed to 1/4-in. in a set of rolls before passing to No. 2 sampler. Between No. 2 and No. 3 samplers, the ore is again mixed in a mixing barrel. The final sample, consisting of one pound per ton of ore, is taken to the laboratory, where it is further crushed to 1/8-in. in a coffeemill, and then riffled down to the size required for grinding in a pulverizer. The capacity of the crushing and sampling plant is up to too tons per hour, depending upon the character of the ore. After sampling, the ore is stored in five ore-storage bins, consisting of four 200-ton bins and one 175-ton bin. Each of these bins is discharged by means of belt feeders and conveyor to the ball mills, so that ores may be composited for milling in any required ratio, or milled separately by themselves. Fine grinding is done in one 6 by 4-ft Allis-Chalmers ball mill and one 8-ft by 36-in. Hardinge mill. These two mills both discharge to one 54-in. Akins Simplex Highweir classifier. The classifier sands can be returned to either or both mills, so that flexibility in grinding for different ores is easily obtained. Flotation equipment consists of four 66-in. Fagergren machines for copper-lead roughing and six similar machines for zinc roughing. Lead-copper bulk concentrate is cleaned and recleaned in eight No. 18-S Denver machines, and zinc concentrate is cleaned in three 66-in. Fagergrens. Copper-lead differential separation

Jan 1, 1947

By R. E. Zimmerman, Shiou-Chuan Sun

An evaluation of the mechanism surrounding the froth flotation of coarse coal and mineral particles as a result of experiments conducted at The Pennsylvania State College. Maximum size ranges for both bituminous and anthracite coals were established as well as the factors affecting the floating of coarse particles. CONSIDERABLE interest is developing in the froth flotation of coal and the maximum particle sizes which can be treated by such method. The economic necessity of recovering extreme coal fines and slurries plus the restrictions being placed upon stream pollution have brought about many new and prospective installations of flotation plants. Most coal slurries or silts have a wide size range, some sizes of which may be unsuitable for effective froth flotation. This fact also enters into the froth flotation of other minerals and the principles that SHIOU-CHUAN SUN and R. E. ZIMMERMAN, Members AIME, are Assistant Professor and Division Chief, respectively, Division of Mineral Preparation, The Pennsylvania State College, State College, Pa. Joint AIME-ASME Fuels Conference, French Lick, October 1949. TP 2843 F. Disccussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Sept. 12, 1949. apply to coal would also apply to minerals in general. A series of experiments were made by the authors for the purpose of investigating factors influencing the froth flotation of coarse mineral particles and an attempt has been made to evaluate those factors. This paper presents the results of a study of the froth flotation of coal particles in the size range greater than 35 mesh. During the study a "multi-bubble" hypothesis has been developed to explain the various phenomena observed in the behavior of coarse particles in froth flotation of coal. The terms coarse, intermediate, and fine particles as used in this paper are arbitrary and differ for various minerals. For coal alone the term intermediate particles means that the particle size is within the range of 35 and 200 mesh of Tyler sieve sizes. Sizes of coal particles coarser and finer than this size range are termed respectively as coarse and fine particles. Methods of Conducting Flotation Experiments: All of the flotation tests, except those shown in table 1, were carried out in a laboratory Fagergren flotation machine, using 300-a samples of solids for each test. All mineral samples we; prepared from selected lumps of high purity by crushing, grinding, and screening to the desired sizes. Except coals, all the other samples were cleaned through magnetic

Jan 1, 1951

By A. N. Holden, J. H. Hollomon

Inhomogeneous yielding during the early stages of plastic flow has been observed in many metals and has long been a subject of controversy. Low carbon steel, when strained at room temperature, exhibits a distinct yield point at which the metal ceases to behave elastically and begins to flow plastically without further increase in stress,† often with an actual decrease in stress from that existing at the yield point. One manifestation of this behavior is the familiar Lüders lines. The extent of the yield point elongation (the plastic strain which results without raising the stress above that at the initial yield point) may be several percent. Several explanations of this type of yielding in steels have appeared in the literature:1-3}; 1. The segregation of carbides or other constituents at the grain boundaries of ferrite forms cell-like blocks which break down at a higher stress than that at which the ferrite alone will flow. 2. The precipitation of various constituents within the ferrite itself in some way blocks initial flow until a higher stress is reached, after which a great deal of flow occurs without further increase in stress. 3. The restraining influence of neighboring, less favorably oriented grains in a polycrystal results in a storing up of energy, which on yielding is sufficient to cause the continued propagation of slip bands on the multiplicity of slip systems available in adjacent iron crystals without increase in stress. 4. Local segregation of carbon atoms increases the stress required for the initial propagation of dislocations. The stress required for further deformation is lower.3 Such an explanation would require the presence of upper and lower yield points in single crystals. Low and Gensamer2 have shown that heterogeneous yielding can be eliminated by removal of carbon and nitrogen from polycrystalline steels by wet-hydrogen treatment. They also demonstrated that the re-introduction of minute amounts of carbon or nitrogen caused a return of the yield point. Observations of the initial flow of single crystals containing small amounts of carbon and nitrogen- should provide a clue to the explanation of inhomogeneous yielding. Previous tests of iron crystals4-6 can not be considered conclusive because it is uncertain whether the carbon and nitrogen were satisfactorily removed by the decarburization technique employed. The purpose of the experiments described herein was to determine whether single iron crystals containing either carbon or nitrogen would exhibit in-homogeneous yielding. Experimental Procedures THE PREPARATION OF SINGLE CRYSTALS All crvstals were formed in the following way. Aluminum killed sheet material 80 mils thick was machined into specimens of the outer contour shown in Fig 1. These mildly tapered specimens were decarburized at 730°C for 16 hr in hydrogen that had been bubbled rapidly through water maintained at 70°. The resultant grain size after decarburizing was approximately ASTM 5. Several stress-strain curves were made of the decarburized niate-

Jan 1, 1950

By Louis V. Bender

AfteR investigating the work of coal-dust fired reverberatories of the Canadian Copper Co., at Copper Cliff, Ontario, the management of the Washoe Reduction Works decided to experiment with and ascertain the advantages of using coal dust as a fuel in their reverberatories. Consequently, during the month of June, 1914, reverberatory furnace No. 8 was changed in order to use powdered coal as a fuel. The results obtained by this method of firing are gratifying and show a decided saving in cost of smelting as compared to grate firing with lump coal. The furnace, as remodeled, is 124 ft. long by 21 ft. wide, and varies in height from 8 ft. 6 in. at the back end to 5 ft. 7 in. at the skimming end. The general construction of the furnace is similar to that of the other furnaces at this plant. There are no side doors to this furnace, as it was thought that with the present arrangement for feeding no "fettling" or "claying" would be required. The interior of the furnace can be inspected through the burner port holes, after shutting off the burners and giving a few seconds' time for the gases inside the furnace to clear away. The charging is done on either side of the furnace from longitudinal hoppers, extending a distance of 74 ft. from the back end of the furnace. Leading from the hoppers into the furnace are 6-in. pipes, spaced 191/4 in. apart, through which the charge is intermittently dropped. The charge is kept well above the slag line at all times; in this way the side walls are protected and no fettling is needed on this portion of the furnace. The remainder of the furnace requires fettling. After operating for three months, we found that the bricks were eaten into along each side wall from the skimming door back to the point where the charge had been dropped. The depth of this cutting away was 8 in. close to the front end and gradually tapered to zero at a distance of 50 ft., and was greatest on the side of the furnace having the larger flue connection. Hoppers will be put in for the entire length of furnace, from which fettling material will be dropped, to prevent this cutting. After the run of three months, the roof was in excellent condition. At the back of the furnace the bricks were not cut into at all; at 30 ft.

Jan 1, 1915

By Henry N. Doyle

Basic procedures in the mining industry have changed only slightly over the centuries since metals and fossil fuels became an essential part of man's economic and cultural life. Mining techniques of the 20th century bear a close resemblance to those of the ancients: exploration, ore breakage and removal, hoisting, and processing. The great advances, however, have been in equipment and machinery of greater size and speed which allow greater efficiency in each of these operations, with a corresponding reduction in manpower requirements. Yesteryear production was measured in pounds per man-day; today a giant and complex, but highly efficient, continuous mining machine can remove as much as eight tons of material a minute from the coal face. If our energy and metal demands of the future are to be met, and at this time it can be assumed that coal will continue to supply a significant part of the energy demand, other dramatic and spectacular technologic advances must be accomplished. Along with mechanization, however, public policy will require the industry to place greater emphasis on health and safety protection, as has been well demonstrated by recent actions of Congress. Together, fossil fuels and metals formed the basis for the industrial revolution-coal to develop power and metals to transform power into useful energy. Strangely enough, however, the mining industry the world over has lagged behind the continuous social changes brought on by the industrial revolution, such as preventive health and industrial hygiene services, and other programs directed to the well-being of the worker. In some countries this resistance, to change may have led in part to the nationalization of the coal industry. Whether this disinclination to social change in the industry of the United States reflects managerial attitudes, inept labor leadership, government neglect, or economic relationship would be the subject of an interesting study. Doubtless the mores of miners and their resistance to change, as well as their geographic isolation from other industrial groups, may have had a strong influence on these factors. In every major coal mining country the accident rate in the coal industry is substantially higher than other industrial groups, and the cost of pneumoconiosis compensation in some countries is greater than the combined costs for all other occupational diseases from all other industries. The high social cost of occupational accidents and diseases may have been a factor in the closing of the industry in at least two countries. Despite diminishing manpower needs, the industry is faced with critical manpower shortages. Miners once reared their sons to be miners; now it appears that the opposite is true. This factor alone, however, does not explain an acute labor shortage in the industry. Traditionally, the industry drew much of

Jan 1, 1976

By W. E. Rice

The ceramic industry has to do with forming or molding articles of clay, and imparting to them their characteristic properties of permanence, strength and color by subjecting them to heat treatment in kilns. This heat treatment is commonly known as "firing" or "burning." The art of firing clay ware antedates the industrial use of coal; hence wood was the fuel first used, and the earliest kilns were built to burn wood. The majority of the clay ware produced today is fired in periodic kilns that are essentially enlarged structures similar to the earliest enclosed kilns; a kiln consists of a large chamber 16 to 32 ft. dia. (or rectangular) in which the ware is charged and fired either in direct contact with flame or hot gases from the fuel, or in saggers which shield the ware from direct contact with the gases. The fuel is burned in a number of small furnaces built in the thick wall that encloses the chamber; these furnaces are from 16 to 36 in. wide and from 3 to 5 ft. long; some of them have horizontal or sloping grates, but many have no grates; the last are called "dead-bottom" furnaces. The temperature necessary to mature the charge in the kiln varies for different clays; for some it is as low as 1800°, and for others as high as 2700" F. Wood was an ideal fuel for the low temperatures that were used in early kilns; it burns freely and produces a long, clean flame, which promotes uniform distribution of the heat in the kiln; it does not coke and so restrict the passage of air through the fuel bed; the ash does not melt in the fuel bed to form clinker; and the ash that is carried into the chamber and deposited on the charge does not contain iron and sulfur to discolor the clay. The extent of the ceramic industry now precludes the general use of wood in kilns, so that today this industry is one of the large users of bituminous coal, burning more than eight million tons annually in kilns. Manufacturing plants usually are at or near the source of clay, with deposits of coal suitable for kilns occurring near the clay. The cost of coal is the largest single item of expense in the manufacture of clay ware, and, because all coals are not equally suitable for the process, the careful selection of coal is important. In this selection the desidera-

Jan 1, 1932