Search Documents

By C. J. Barber

This paper Donald describes how New Jersey Zinc Co. made surveys for a connection between the Ivanhoe and Van Mater shafts at Austinville, Va. Except to say that the two faces had to meet "accurately" on line and grade, Donald does not indicate the required precision. Assuming that there were 24 angles in the 1 ½ -mile traverse and 15 in the one-mile traverse, it can be shown that if the average error in plumbing each shaft was ±30" and the average error in measuring each traverse angle was ±10", then the average error at the point of connection would have been about ±1.9 ft normal to the line between the shafts. This calculation assumes that any errors in the triangulation would be negligible compared with the errors in the plumbings and traverses, and it also neglects taping errors. With no constant errors or blunders, the latter would be important only in lines normal to the line between the shafts.

Jan 7, 1959

By Walter Scott

THE removal of lead by fire refining methods from copper of electrolytic quality is growing in importance. Particularly is this true of the refining of secondary copper and copper cathodes obtained from electrolytic cells where lead is used as the anode material, as in the electrolysis of ore-leaching solutions and foul electrolyte. When investigating the removal of small amounts of lead from molten copper in a reverberatory furnace during the refining of secondary copper of otherwise electrolytic copper quality,1 it was found necessary first to FIG. 1.-SAMPLING DEVICE. know something about the distribution of the lead throughout the bath. The authors believe that it is not generally known how small amounts of lead as an impurity are distributed in a molten copper bath; that is, whether the lead is concentrated at the bottom or at the top, or whether it occurs more or less uniformly throughout the bath. The data contained in this report may help, therefore, in the development of a satis-factory fire refining method for the removal of this obstinate element from a molten copper bath.

Jan 1, 1930

By Andrew A. Blair

The increased importance and value of chemical analysis in connection with metallurgical operations is largely, if not entirely, due to the increased accuracy of the analytical methods used for the quantitative determination of the foreign elements always associated with the metal operated upon. This applies especially in the working of iron and steel, and to the determination of the amounts of such elements as phosphorus, carbon, and silicon. The influence of greater or smaller amounts of these elements upon the physical properties of iron and steel will be better understood when the proper experiments shall have been made upon samples whose chemical composition is known with almost absolute certainty. From the present standpoint of analytical chemistry, it is easy to see that at least one reason for the failure of many attempts to solve this problem, is the inaccuracy of the analytical methods used. Even at the present time the frequent want of agreement (over and above the unavoidable error due to manipulation) between chemists working on the same sample, leads one to think that there is still at least a choice in the methods used. It is true that very frequently a faulty method in the hands of a skilful analyst may be made to give corroborative results

By Robert L. Wilson

Computation of reserve tonnages, stripping ratios, and grade of ore has long been a revolting aspect of the young mining engineer's job. Weeks at the desk calculator may turn into months before a single job is completed. Then many additional hours are necessary to check the calculations. During the last decade, computing machines have been widely publicized as instruments which will accomplish fantastic feats. Tales of their magical qualities have overshadowed their most basic characteristics-that of being a labor-saving device. Prior to a discussion of the electronic calculator's use on a mining problem, it may be well to point out that these machines are neither magic nor will they replace the judgment of an experienced engineer. In short, the "mighty morons," as the computors are sometimes called, are excellent labor savers but must be used correctly. They are not a substitute for thinking.

Jan 6, 1961

By Geo. W. Goetz

The following tables show the analyses of ores from nearly all of the mines which will produce over 10,000 tons of ore each during the season of 1890. There are many small mines now in the course of development, some of which may become large producers. Many of the mines produce several different grades of ore, but the analyses given in the tables are fair averages of ore such as the respective mines can deliver. Most of these analyses were obtained from the agents of the respective ores, and are averages of the season of 1889. One can state positively that over 75 per cent. of all the iron-ores of the Lake Superior district will average over 60 per cent. of metallic iron. During the past 34 years this region has produced about 48,137,421 tons of ore, the different districts contributing about as follows: Marquette District,. 29,754,057 Menominee " .10,415,859 Gogebic " . 6,622,194 Vermilion " . 2,342,991 Miscellaneous,. .. .. 2,320 In the year 1889, the product of all the districts was nearly '1,300,000 tons. The product of the entire region for the season of 1890 may exceed 9,000,000 tons. This large amount of ore is shipped to the lower lake ports, from Escanaba, Marquette, Two Harbors and Gladstone.

Jan 1, 1891

By S. A. Braley

Drainage of acid mine water into surface streams of coal mining areas is one of the most serious problems of stream pollution, since there is no known method that completely prevents its forming and no economically feasible treatment after it has formed. The mine acid problem differs from other pollution hazards because acid production does not end with cessation of mining but actually becomes more evident when pumping is stopped. The acid problem in the Pennsylvania, Ohio, West Virginia, and Kentucky bituminous coal areas of the U. S. began with the first operation in 1761, and the volume of acid discharge today is largely the cumulative result of years of mining. Provided they lie above the drainage area, the oldest mines, now long abandoned, are almost without exception producing acid in the same manner as those now operating or recently abandoned.

Mar 1, 1956

By Joseph A. Sutton, John D. Corrick

The continuing depletion of high-grade ore de- posits in this country has created a need to develop more effective methods for recovering valuable metals from low-grade ores. The use of microorganisms for their biochemical reactions is one possible way to solve certain phases of this problem. Bacteria have been used successfully by many diversified industries. Until recently, however, little attention has been focused on the use of bacteria in mining and metallurgical processes. This report summarizes one phase of the microbial studies being conducted at the U.S. Bureau of Mines, College Park Metallurgy Research Center. The two-fold objective of this study was, first, to determine if pure strains of the bacteria Ferrobacillus ferrooxidans, Thiobacillus concretivorus and Thiobacillus ferrooxidans could utilize the iron and sulfur occurring in sulfide minerals to produce appreciable quantities of ferric sulfate and sulfuric acid for dissolving copper and, second, to develop the chemistry involved in the microbial oxidation of sulfide minerals. These are of particular interest as they relate directly to the feasibility of employing microorganisms in leaching operations.

Jan 6, 1963

By Frank Somogyi, Donald H. Gray

Techniques for in-situ dewatering of tailings and slimes include evaporation, decantation, drainage under self weight, drainage by surcharging, and electro-osmosis. A promising technique for increasing drainage efficiency is a vertical, wall-drain system, which can be constructed in an impoundment concurrently with deposition of slurried tailings. The vertical drains, which can be constructed from sand or from the coarse fraction of a tailings stream, greatly speed the rate of consolidation of the fine tailings or slimes. The performance of a wall drain system and the semitidy of consolidation efficiency to certain variables or system parameters are examined. These parameters include the slime deposition rate, ratio of drain to slime permeability, drain width, and drain spacing.

Jan 1, 1979

By F. F. Aplan, G. Simkovich

Zinc oxide, an n-type semiconductor, and nickel oxide, a p-type semiconductor, were studied in electrostatic separation experiments in pure and doped forms. In addition, pure potassium chloride and potassium chloride containing one volume per cent silver were also investigated. It was found, in agreement with theory, that the presence of dopants in the oxides could either increase or decrease the electrical conductivity of the base compounds and, thus, control the response of these particles to electrostatic separation. Further, it was shown that the same dopant in the n- and p-type semiconductors produced opposite conductivity effects; again in accord with theory. Finally, it was found that the presence of dispersed silver particles in the normally insulator phase potassium chloride produced sufficient electronic conductivity to cause the silver containing particles to respond as would materials possessing "medium-type" conductivities.

Jan 1, 1980

By D. O. Rausch

The economic relationship between steepening slopes and decreasing waste removal requirements ahead of ore mining is one of the most important factors in the design of open-pit mines. The steepness and stability of the pit slopes often spells the difference between ore and waste profit or loss in low cost open-pit operations. Unfortunately, the technology necessary for designing stable rock slopes is still in the early stages of development. Past and current pit-design methods have been, and still are, empirical, with rock slopes frequently made too steep or too shallow. As such, large expenditures are often made for correcting slopes after failures occur, or for unnecessarily removing more waste material than required.

Jan 6, 1965

INTRODUCTION The first installation of large, commercial, high gradient-high field cannister and matrix magnetic separators for removal of impurities from kaolin was made in 1973 (1). Since then the technology and equipment have been widely adopted for clay processing with about 12 units in commercial use. These new separators have filled a need, caught the imagination of many and become a technology worth fighting for. A fight has occurred, and a resolution on royalties for kaolin processing, at least, has been achieved. LIMITATIONS TO APPLICATIONS OF MAGNETIC SEPARATORS Other than the use of these magnets on kaolin clay, no other application has yet achieved widespread adoption. Dr. Iannicelli blames inertia, and1 would agree that it is a factor. There are other reasons too, and if they are examined, they may isolate problems that R&D can significantly assist in solving. I'd like to break the problems into two areas. Machine limitations - the mineral properties are there but performance is insufficient or uneconomic. Separation limitations - the mineral properties aren’t there, but the magnetic separation would perform well if the properties were there (size is right; concentration is right, etc).

Jan 1, 1979

The Library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references, and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 4, 1918

By Donald C. Violetta

LIMITATIONS of the sintering process as applied to the agglomeration of fine iron-ore concentrates are related directly to the sizes and aggregating properties of the ore particles. A normal sintering mixture is composed predominantly of material which ranges in size from 5/8 in. to 100 mesh, whereas concentrate is composed of material which ranges in size from 100 mesh to less than 10µ. Unless the concentrate has high aggregating properties, it is quite impervious to a gas stream and, as such, inhibits the capacity and operability of the conventional sintering process. Material has Poor Aggregating Properties Aggregating properties, in this case, may be defined as the ability to form small agglomerated fragments or accreated masses by a normal mixing action, and the ability to maintain these shapes during drying and firing. Coarse-screened ores are a natural aggregate, and fine, slimey ores have good aggregating properties. However, specular-hematite flotation concentrate has a very low tendency to aggregate, due to its particle sizes, shapes, and surface chemistry and, as such, is readily air borne in a gas stream when dry.

Jan 3, 1958

By John A. Church

In May, 1878, I had the honor of presenting to the Institute, at the Chattanooga meeting, some observations upon the heat of the Comstock Lode, and since then the subject has attracted some attention and criticism, in the course of which, L have observed errors of apprehension which I beg leave to correct now. Mr. John Arthur Phillips discussed it before the Geological Society, his paper being printed in the Quarterly Journal for August, 1879." His criticism is based upon that part of my paper in which I quote a number of analyses of the mine waters, to illustrate the fact that the heat does not come from the oxidation of pyrite. I pointed out that these waters contain only an insignificant proportion of sulphuric acid, and not enough to account for even one per cent. Of

Jan 1, 1880

Optimism over the continued growth of coal ex- ports received a significant shot in the arm September 18 at Norfolk, Va., when huge, new ship coal-loading facilities of the Norfolk & Western Railway were formally dedicated before a large audience of American and foreign dignitaries. Guest of Honor at the occasion was Christian A. Herter, Special Representative for Trade Negotiations, who, in a speech, stated, "The prospects for the expansion of our coal exports are excellent. The competitive pricing and high quality of our coals, whether for the production of coke for steel mills or for the generation of electric power, have won the respect of consumers everywhere in the world. Last year, the United States coal industry exported over 40 million net tons. . . . There are excellent reasons to believe that by 1970 we shall be exporting at double this rate."

Jan 10, 1963

By A. J. Nicol

Field experience in uranium has shown it is most economical to ram through a drilling program to obtain maximum footage per drill hour. Drift surveys can then determine the course of the holes. Using this method is generally cheaper than paying the additional cost involved in using the drilling technique and equipment necessary to maintain straight holes. Factors Affecting Direction of Bit Travel: In all rotary-drilled holes there is an interplay of forces or conditions affecting the direction of bit travel. Rarely is a straight vertical hole obtained. One of the major factors is weight on a drill string. In looking at a joint of drill stem it is hard to imagine its being quite flexible, but flexing of the steel increases when many joints are made up together, and even a slight weight added to the upper portion causes a buckling or spiraling effect in the hole. The result is that the bit deviates from the vertical.

Jan 1, 1959

By D. A. Dukelow

By using the U. S. Steel oxygen sensor to measure the oxygen content of the steel, deoxidation practices have been developed for silicon-killed fine-grain steel produced by the basic oxygen process. Measurements of oxygen content taken at final turndown are related to the amount of the aluminum addition to the ladle necessary to obtain the desired aluminum analysis for proper grain refinement. In comparison with heats deoxidized by the standard approach, which is based on carbon content, the heats deoxidized according to the oxygen-sensor-based schedule showed a 25 percent decrease in variability from the desired aluminum content. As more heats of a particular grade are made, it is expected that improved quality will result in decreased rejections and better analysis control. Sensor-based deoxidation schedules are also being developed for semikilled, rimmed, and capped steels.

Jan 1, 1972

By John Birkinbine

What is believed to be an Aztec, or possibly a Toltec, mirror, is claimed to have been taken from one of the tombs at Cholula, near the city of Puebla, Mexico, where there is a mound of considerable size, in fact a hill, largely constructed of adobe bricks by the Toltecs, or by those who antedated them. The mirror is formed from a mass of what is evidently pyrite, is nearly a true hemisphere, having a diameter of 3 1/8 inches, and weighs 19 ounces. From its unusual size it is believed to have been hung about the neck of an idol. Other Aztec mirrors of smaller dimensions, and of less weight, so as to be carried about the person, are known; but the one exhibited, being heavy, was apparently intended to be held in the hollow of the hand, in which it fits, and may have been utilized to flash heliotropic signals. The entire surface, both of the base and of the convex portion of the hemisphere proper, has been beautifully polished, but, for some reason, the mirror has been shamefully abused, the edges having been broken, and the center of the base defaced, possibly by some one testing it for precious metals. Near the top of the hemisphere a hole, one-fourth of an inch in

Jan 1, 1895

MR. CHARLES F. RAND, President, BUTTE, MONT., APR. 29, 1913. American Institute of Mining Engineers. Dear Sir: In conversation here with Mr. Sales, who is much interested in the work of the Committee on Mining Geology, he made a suggestion which you may be interested to hear. He, and many of us, are interested in papers along our lines of special activity, as they appear from time to time in the Institute Transactions, and often take these papers with us into the field. It appears that the work of special committees which are being formed is likely to result in a much greater number of available papers than the Institute has ever before been called upon to publish. This year's Transactions, for instance, have to be published in two volumes. Why would it not be a good plan, instead of printing heterogeneous volumes, to classify the papers into several volumes, under main headings such, for instance, as iron and steel, precious metal mining, and mining geology ? We would, in fact, be very glad to suggest this as a topic for discussion, if you think it wise, in response to the Secretary's letter of April 18. Very truly yours, J. W. FINCH.

Jan 5, 1913

By Thomas N. Walthier

Ocean miners seem prepared to commit upwards of $50 million, spread over the next 10 years, to develop a deep ocean capability. More and more large companies, Kennecott, Inco and Tenneco, to name a few, singly or through consortia, are spending money, often big money, to obtain a viable and profitable marine mining industry. Much of the current involvement of the mining industry in the oceans is concerned with either exploration for or engineering studies of manganese nodule deposits and most of it is considered highly proprietary. Thus, the scope of the total effort can only be surmised. The following provide a good indication as to the magnitude of the over-all effort: (1) Hughes Tool Co., Oil Tool Division, announced last March it has been performing engineering studies and ocean surveys (in collaboration with Global Marine, a subsidiary of Tenneco Oil) for the purpose of developing deep ocean mining equipment and techniques. As a result of these studies, Global Marine will build a 35,000-ton prototype deep sea mining ship for Hughes. (2) Deepsea Ventures, Inc. has been "assiduously compiling data on the location. depth, and composi-

Jan 1, 1971