Search Documents

By H. M. Bouton, G. S. Phipps, E. E. Schumacher

The seriousness of the present tin scarcity has stimulated large consumers of this vital metal to develop drastic conservation measures in order to extend the available supplies to cover the emergency period. By devising new soldering methods and alloys the Bell System has contributed a substantial share in the tin conservation effort. Fortunately, the changes, as far as can be determined now, have not introduced weakness into the soldered joints. Some of the new procedurcs were already in the process of development at the onset of the emergency, while others were devised under its stress. In some instances, the newly developed solders were found to be more difficult to use than the alloys previously available, and would not have been introduced under normal conditions. One major change made that previously had been under consideration will result in large savings of tin. Unless service difficulties are encountered, this modification gives promise of remaining after the emergency has passed. The change involves a reduction in the amount of solder placed on a wiped joint between the cable sheath and the sleeve. Instead of the customary full sized wiped joint, a wipe of fillet proportions is formed. Through this change, a solder saving of more than 60 per cent per joint can be realized. Plumbers and cable splicers for many years have joined lead pipes and cable sheath by a soldering process called " wiping." The name is an apt description of the operation. For a wiped joint, the sections to be united are heated by molten solder poured over their surfaces, and the resulting semiliquid mass is manipulated by wiping with cloth pads to a well rounded symmetrical form like the one shown in Fig. I. The operation requires considerable skill on the part of the splicer and close control of the composition of the solder. At first consideration, the problem of tightness in such joints seems simple but experience shows that even under the best conditions the fissures frequently found in the solder occasionally link and form a path that allows leakage to occur. In telephone cables not maintained under gas pressure, such leaks permit the entrance of water, which wets the paper-covered conductors and thereby impairs the insulation value and causes service interruptions. Ry going to an extreme and wiping off all the solder in excess of a fillet, it has been found that many causes of porosity are eliminated. Figs. 2 and 3 show cross sections of joints wiped in the old and the new ways. The saving in solder, and consequently in strategic tin, is evident. The field splicing forces find that joints are easier to make by the new method and are less likely to be porous. The metallurgical considerations that are responsible for the success of the fillet wipe are of interest. Much has been written about the wiping process of soldering cable joints and the many requirements of a good wiping solder have frequently been listed. The success of the procedure described

Jan 1, 1943

By D. F. Stoneburner

The thermoelectric power and electrical conductivity of a series of liquid alloys of thallium were determined in order to study the relation of chemical bonding to semiconduction in liquids. The results indicate metallic behavior for the alloys of thallium with arsenic, antimony, and bismuth, while the sulfides, selenides, and tellurides indicate semiconduction. The results are compared with the Properties of the same alloys in the solid state. This work supports the observation that long-range order is not a necessary requirement for semiconduction. PREVIOUS work1,5 has shown that some sulfides and oxides behave as semiconductors in the liquid state. Although the band theory has been of great help in understanding the properties of solid semiconductors, its quantitative application to liquids is difficult. The very existence of liquid electronic semiconductors shows that ascribing the discrete structure of the energy spectrum to strict lattice periodicity, or long-range order, is not always satisfactory. Rather, the short-range order determines the structure of energy levels and the width of the forbidden gap and, consequently, the concentration of free holes and electrons. This is borne out by the analysis of data accumulated by Regel and coworkers.6 The similarity of electronic structure of liquid and solid phases of certain liquid metals was pointed out by Knight et a1.,7 who examined nuclear resonance in solid and liquid Li, Na, Rb, Cs, Mg, Al, Ga, Sn, and Bi. They found noticeable changes in the electronic structure upon melting only in the cases of bismuth and gallium. They concluded that "a liquid metal possesses a band structure which is very like that of the solid, provided the short-range structure is not altered during melting." In semiconductors in which the near-neighbor arrangement remains the same on fusion, the material would be expected to retain its semiconducting properties. The quantum theory of semiconductors, with its band structure of energy levels, is linked exclusively to long-range order. Furthermore, it has limited usefulness in predicting new semiconductors. Many sulfide8-12 have made comparisons of properties on the basis of crystal structure or the position in the periodic table, both methods involving the same factors as chemical bonding. Mooser and Pearson8"10 have pointed out that crystal structure depends on chemical bonding, and that this bonding is a property of the atoms themselves. As the periodic arrangement of the atoms offers an easy comparison of such factors as atomic weight and number of valence electrons it provides clues to expected similarities of bonding for various elements or groups of elements. This approach has led Mooser and Pearson to formulate their valence-bond theory of semiconduction, in which they define a semiconducting bond. These authors state that "semiconductivity is the result of the presence in a solid of predominantly covalent bonds. These lead, through the process of electron sharing, to completely filled s and p orbi-tals in the valence shells of all atoms of elemental semiconductors while in semiconducting compounds only one atom of any two bonded together need acquire closed s and p orbitals. The presence of empty 'metallic' orbitals in some atoms of a compound does not destroy the semiconductivity provided that these atoms are not bonded together; it may, however, give rise to pivoting resonance in

Jan 1, 1965

By John D. Gill

The purpose of this paper is to invite attention away from the obvious. direct monetary costs of oil-field overdevelopment (as distinguished from "social costs") to a consideration of the role played by the exercise of freedom to create even allegedly excessive1 plant facilities in contributing to the maintenance of equilibrium in the wholc economy and in promoting material progress. The obvious and most commonly discussed effect of overdevelopment of oil fields is illustrated by the allegation that already the excessive development of the East Texas field has cost upward of $162,000,000;2 in other words, the drilling of 12,500 wells more than the number estimated as the requirement for economical recovery of the reserve has unnecessarily raised the total cost of development that amount. Many other illustrations of so-called excessive development of oil pools could be presented. Some of them, like Cushing, Powell and Long Beach, might be drawn from the era antedating widespread discussion in the trade of such matters as optimum well spacing, reservoir energy, the conservation rate of depletion of reserves, etc. Numerous other cases can he found in the records of the current era, which began with the introduction of rationalized restriction of production. Besides East Texas, there may be mentioned Oklahoma City, Centralia and. more recently, the town-lot development of Bloomingdale, Michigan.

Jan 1, 1940

By Alan U. Seybolt

In examination of some cold-rolled copper and cupronickel that contained a little columbium, it was discovered that these alloys were unusually resistant to annealing. This effect was suficiently pronounced to warrant some investigation of the annealing characteristics of such compositions. Experimental Procedure The alloys were made from cathode copper, electrolytic nickel, and a special copper-columbium hardener alloy furnished by the Electro Metallurgical Corporation. This hardener alloy contained 10 per cent columbium, with tantalum, aluminum and iron as major impurities. The melting was carried out in a clay-graphite crucible in a high-frequency induction furnace! under a charcoal or electrode carbon cover. No deoxidizing additions were made. The 7-lb. copper heats were poured into a steel mold, hot-rolled to 1/4-in. thickness, and annealed for 56 hr. at 760°C.; the cupronickels were annealed I hr. at 815°C. The material was then cold-rolled to a 50 per cent reduction in thickness and annealing tests were carried out on this 1/8-in. hard-rolled strip. A little silver was added to copper-columbium alloys 402 and 403 to find out

Jan 1, 1942

By A. H. Miller

TEMPERATURE considerations are of prime importance in the manufacture of steel products-front the time the metal is produced in the melting furnace, where the chemical reactions have a direct dependence on the temperatures of the bath, to the final machining of work on which the expansion due to the rise in temperature of the forgings during machining must be allowed for. Methods employed and difficulties encountered in some of the more important steps are here outlined. These methods are the result of years of experience, with many methods of temperature determination, and have been successful in routine works practice in the manufacture of high-quality steels. In the operations of melting, forging, and heat treatment, if the product is to be of the best quality each operation must be carefully followed through. A high-quality product cannot be obtained even with the best heat treatment if the steel is poorly melted, and, conversely, the best steel ever made may he spoiled by inefficient heat treatment. To perform the best work in any of these operations, temperatures must be accurately regulated.

Jan 8, 1919

By Norman Yarborough

Much has been written about the energy fuels including their standing with respect to reserves, their delivered Btu costs, their potential in the electrical generating market and their capabilities to meet a burgeoning demand. Yet, when all factors are placed in their proper perspective, the spiraling electrical energy market alone should guarantee each fuel a better than average market for the foreseeable future. In fact, a study made by the U.S. Federal Power Commission on the spare capacity utilities have on hand indicated that 39 of the 181 major utility systems had less than 10% reserves on hand at the end of 1969. Fuel supplies are critically low in some areas, especially in the Southeast, South Central and Midwest areas of the U.S. In other systems equipment shortages resulting from faulty equipment or delays in getting new equipment deliveries causes power failures during peak loads. In addition, lack of labor curtails the erection of some new facilities and prevents many other facilities from operating at capacity.

Jan 1, 1970

By R. H. Heinen

Introduction Drilling is the initial operating step In open pit mining. It goes hand-in-hand with the blasting operations to ensure adequately broken material for the excavation equipment employed. The drilling effectiveness is highly dependent on the quality of the drill evaluation. This discussion will center on the parameters that are needed to evaluate drill requirements for a new mine The procedure that is generated can, however, be used to evaluate whether to expand existing operations and replace existing equipment. Methods of breaking ground, other than blasthole drilling and blasting, such as ripping, will not be discussed. The importance of correct drill evaluation extends to the other facets of open pit mining. Inadequate fragmentation, the direct result of poor drilling and blasting techniques, results in oversized, hard digging for the excavating equipment. The result is higher secondary blasting costs, reduced excavation efficiencies, higher excavation costs, higher road repair costs, and higher haulage equipment costs. The main objective of evaluating drill fleet requirements, therefore, is to determine the equipment needed to minimize the operational constraints, caused by blasthole drilling, on other facets of open pit mining at the lowest cash flow costs.

Jan 1, 1979

By Byron E. Eldred

Generally speaking, the practical study of combustion has been made mainly from the stand-point of the steam engineer. This narrow view-point has left open a large field for scientific research on the application of combustion in other arts, where the conditions of heat-utilization are widely different from those presented in the steam-generator. The great economic importance of the boiler and the ease of measuring its performance, together with the comparative uniformity of conditions in the steam-generator, is, probably, quite largely responsible for the practical neglect of the study of the use of fuels in other arts save only on the basis of their thermal value. yet these other arts show quite plainly that a thermal-value basis alone is not sufficient. For example, in burning lime, under ordinary conditions of firing, a cord of wood will do as much work as a ton of coal, though the latter affords more than twice the number of heat-units. Similar results are evidenced in burning brick, in the roasting of certain ores, in reheating billets, and in many other, arts where heat is to be applied over extended areas to fragmental masses of more or less refractory materials. In these arts much is to be gained by a

Jan 1, 1911

By John H. Hollomon

IN a recent paper,1 a very early suggestion by Ludwik2 concerning the nature of the mechanical behavior of metals has been reexamined and extended. In essence it was [ ] suggested that there exists, at least under certain conditions, a mechanical equation of state; that the stress required for flow depends upon the instantaneous values of the strain, strain rate, and temperature, and not upon their past values. It is proposed that under these circumstances the stress does not depend upon past history of these variables, but is like the temperature of a gas that depends only upon the I instantaneous values of the pressure and volume. This notion has not been applied to present day studies of metals, though it is especially applicable to the study of creep. It is the purpose of this paper to analyze the significance and possible range [ ] of applicability of this idea and to deter- mine how it influences the accepted ideas concerning creep. STRESS-STRAIN RELATIONS It is well known that the stress-strain curves of metals are influenced by both strain rate and temperature. For a fixed strain rate and temperature there is associated with each metal a stress-strain curve. If either the strain rate or temperature is changed a new stress-strain curve will be characteristic (Fig. I). A much more general relation between the effects of the sevariables is possible, however. Consider the stress-strain curves of Fig. I determined at

Jan 1, 1946

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, all of the following rock types occur; oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently, overblasting wasted drilling time, and explosives caused excessive throw.

Jan 4, 1974

By George Laird

IF IT IS true that Sir Walter Raleigh lost his head for his failure to find gold in the Guianas, the trumped up charge of "treason" might better have been "con-tributory negligence." That systematic investigation and development of the gold-bearing areas of both Dutch and French Guiana have not been accomplished is not due so much to the lack of gold as to the geo-graphical, physical and climatic conditions of the two colonies. The Dutch, as a people, are not prospectors. The French look upon "Cayenne," or French Guiana, as DJOEKA BOATS USED IN RIVER TRANSPORTATION. just what it is: a penal colony, which produces a certain amount of balata, gold and essential oils, all of which can be purchased from the natives with far less physical exertion than they can be secured from the "bush" or jungle. The colonies have had their gold "booms," and dur-ing these periods the production has increased to a considerable amount, but the hardships to be endured in reaching the fields, the cost of transporting tools and supplies, the ever-present fevers, the bite of the "57 varieties" of insects and, lastly but not leastly, the abundance of rum in the seaport towns, dampen the ardor of even the strongest; the production of gold is left to the "pork knocker" or illegal gold digger and to the comparatively few producing "mines."

Jan 10, 1922

By Herbert A. Wendel

Reaching the miner with safety education" is R the ultimate goal, the main objective, of every safety program in the mining industry. If we can get safety education to every worker, and it is properly learned, enforced and obeyed, we should eliminate at least 85% of all potential accidents. We should then have very few accidents as a result of unsafe behavior, which, in turn, would allow us to concentrate most of our future efforts on preventing the types of accidents which are caused by faulty or defective machinery, equipment, tools and materials. An uninformed or uninitiated person would think that it should be a rather simple process to reach the miner with a safety education. Theoretically he would be right because here we get involved in a matter of semantics. When we say "reaching the miner with safety education" we actually mean that this education must also be accepted and learned by the miner; we intend to mean that safety must be observed and followed at all times. But in order to realize our complete meaning of the phrase, we must find the solution for a number of problems and obstacles which are well known to management and safety personnel.

Jan 1, 1965

By Roger W. Swindle

INTRODUCTION The Uravan Mineral Belt in southwestern Colorado and southeastern Utah is a uranium-vanadium mining district with a unique set of radon daughter control problems. This paper describes these problems and the methods that have been developed to deal with them. The greatest emphasis is placed on the problems caused by air stagnation because these are the most frequently encountered ventilation problems, and this is an aspect of uranium mine ventilation that is often misunderstood. VENTILATION PROBLEMS Most of the mine ventilation problems in the Uravan Mineral Belt are caused by one or more of the following conditions: (1) the highly irregular ore deposits are difficult to locate and delineate, (2) air stagnation occurs in many areas of the extremely irregular mine workings, and (3) it is often necessary to reactivate old workings with small airways that are often caved. Planning Problems Orebodies in the Uravan Mineral Belt are so discontinuous and unpredictable that they are difficult to locate and delineate. Data supplied by surface drilling and underground test holing are often misleading; very little ore may be found in the vicinity of an ore hole, and, conversely, an unmineralized hole may be adjacent to a high-grade ore deposit. Also, ore guides are often ambiguous, and their interpretation is usually a matter of opinion.

Jan 1, 1983

By Daniel Houdouin

Data is frequently collected in mineral processing plants in order to evaluate operating performance or to model process units. Metal concentrations, circulating loads, products flow rates, classifiers efficiencies, flotation units recoveries, grinding mill efficiencies are typical parameters calculated from plant data. The validity of these calculations depends strongly upon the reliability of the data used for that purpose. The objective of this paper is to illustrate that flowrates, efficiencies and rate parameters of mineral processes are more reliable when calculated from balanced data rather than from raw data. Using variance-covariance matrices of balanced data produced by automatic mass balance packages (including flow rates, concentrations, percentage of solids and size analyses), variances of separator efficiencies (flotation or classification) and of mill grinding rates are derived. The variances are compared with those of variables calculated from raw data. The advantage of using balance data is illustrated with real data from flotation, grinding and classification units.

Jan 1, 1984

By James M. Riddle

INTRODUCTION Block-caving mines are generally large operations. Calculating the quantity and value of mineral present and determining the economic limits to mining are complicated processes requiring much time and effort. If these processes are to be worthwhile, they must be accurate and reliable. Success in planning may increase the economic returns significantly. Since capital investments in block-caving mines are generally quite large, and development may span several years, quicker and more accurate methods of mine layout are very worthwhile to the mining industry. The purpose of this study is to develop an approach to the evaluation and layout of block-caving mines. The study included development of a simple approach to modelling ore reserves and a rapid, dynamic programming solution for optimum ultimate mining limits. TRADITIONAL APPROACHES TO BLOCK-CAVING MINE LAYOUT General discussion of techniques of calculating and valuing ore reserves can be found in the literature, (1-4). Mining limit approaches have been investigated by many and follow five general methods: 1, Moving cone method (5) 2. Graphroriented technique (6,7) 3. Dynamic programming technique (7,8,9) 4. Network flow method (10,11) 5. Pillar method (12) Of these investigations, only two were developed for underground mining applications, those of Sharp (9) and Riddle (11).

Jan 1, 1977

By William E. Bruce

This paper is intended to provide an improved understanding of natural draft (natural ventilating pressure) and the effect of natural draft on underground mine ventilation circuits. Attention is focused on measurement of natural draft pressures during ventilation surveys in mechanically ventilated mines and on different methods for modeling natural draft using the measured data. A number of examples are presented which utilize data collected during absolute air pressure surveys made by personnel of the Ventilation Division of the Mine Safety and Health Administration's Safety and Health Technology Center, Denver, Colorado. Examples are used to illustrate how the data from absolute air pressure surveys may be interpreted to determine whether natural draft pressure is present and what its magnitude is. In addition, two different methods are described for mathematically estimating the magnitude of the natural draft pressure. Comparisons are made of results obtained using the different methods. Different procedures are described for modeling natural draft using the MSHA-modified Penn State computer program. Use of the routines is described and illustrated relative to drafts that aid or oppose the mechanical ventilation system. Tabulations of results facilitate comparison of outcomes obtained using the different modeling procedures.

Jan 1, 1982

By Alan U. Seybolt

In examination of some cold-rolled copper and cupronickel that contained a little columbium, it was discovered that these alloys were unusually resistant to annealing. This effect was suficiently pronounced to warrant some investigation of the annealing characteristics of such compositions. Experimental Procedure The alloys were made from cathode copper, electrolytic nickel, and a special copper-columbium hardener alloy furnished by the Electro Metallurgical Corporation. This hardener alloy contained 10 per cent columbium, with tantalum, aluminum and iron as major impurities. The melting was carried out in a clay-graphite crucible in a high-frequency induction furnace! under a charcoal or electrode carbon cover. No deoxidizing additions were made. The 7-lb. copper heats were poured into a steel mold, hot-rolled to 1/4-in. thickness, and annealed for 56 hr. at 760°C.; the cupronickels were annealed I hr. at 815°C. The material was then cold-rolled to a 50 per cent reduction in thickness and annealing tests were carried out on this 1/8-in. hard-rolled strip. A little silver was added to copper-columbium alloys 402 and 403 to find out

Jan 1, 1942

By Alf Holmelid

Until recently the only automatic control of electric parameters in submerged-arc furnaces has been electrode control with electrode current or electrode impendance as controlled variables. Elkem Research and Development Centre has delivered this kind of control for a long time, both stand- alone controllers and control algorithms incorporated in an integrated computer control system. In recent years we have noticed increasing interest in more sophisticated electric control. Results both from pilot-plant experiments and from production furnaces show that proper electric conditions in the furnace are more important to the furnace operation than was assumed earlier. Optimal electric conditions lead to lower power consumption per ton of metal and allow use of cheaper raw materials Besides, power contracts and the market situation lead to more frequent change of load on the furnaces. Therefore it is important to vary the load in a way that allows proper electric conditions to be maintained. Based on this renewed interest in electric control, Elkem Research and Development Centre has carried out a project, starting with analysis of existing electric instrumentation and control algorithms for electrode control, and ending up with an integrated electric control strategy including power-demand control as shown in Figure 1. In this paper we will give a resume of this work and present a new integrated control strategy put into operation for the first time in June 1983. [ ]

Jan 1, 1984

By R. J. Lipp, I. Iwasaki, R. H. Heerema

The presence of calcium ion in iron ore pulps that are upgraded by selective desliming can result in indiscriminate flocculation of both iron oxide and siliceous gangue slimes. In order to overcome this adverse effect, deflocculation by three complexing agents, namely ethylenediaminetetzaacetate (EDTA), sodium tripolyphosphate (STPP), and sodium hexametaphosphate (SHMP), was investigated. The precipitates and complexes of these agents with calcium ion were characterized by potentiometric and conductometric titrations, and the surface properties of quartz and goethite were studied in the presence of calcium ion and of the complexing agents by means of streaming potential measurements and flotation tests. The results were then correlated with selective flocculation tests on an artificial mixture of quartz and goethite. EDTA markedly improved the selectivity of flocculation when added in near stoichiometric amounts, whereas STPP was less effective and SHMP was totally ineffective due to strong, indiscriminate dispersion. Remanent calcium polyphosphates on the goethite surface interfered with the adsorption of starch flocculant.

Jan 1, 1983

By F. J. Escandon V.

The Plomosas stratiform lead and zinc deposits are located in northeastern Chihuahua in a sequence of folded Paleozoic and Jurassic rocks. They consist mainly of channel or blanket-like bodies of ellipsoidal cross section restricted to a 60-in-thick shaly limestone and a 30-m-thick marble horizon of La Casita formation, with some reemplacement veins and shoots within the Plomosas formation. The mineralogy consists of iron-poor sphalerite, galena with a small silver content, and pyrite, in a gangue of calcite, barite, and minor quartz. The ore bodies present a lateral zoning with zinc-lead ratios increasing to the northwest. Vertical zoning shows marked changes in zinc-lead ratios and in the width and tenor of the ore which cannot be related to sedimentary or diagenetic features. Transgressive mineralization and some small fissure veins and breccia pipes also point to an epigenetic origin. Sulfur isotope analysis and geochemical data indicate hydrothermal solutions. Texture of the ores in the Mina Vieja marble is coarse, but in the Cuesta shale it is banded along bedding. The low iron and silver content of the sphalerite and galena and the weak hydrothermal alteration (only marbleization) of the wall rock suggest a telethermal stage of the solutions. There is no evidence of a possible intrusive rock mineralization.

Jan 1, 1976