Search Documents

By Christopher W. Schram, Allan B. Tanner, Frank E. Senftle, George R. Boynton, Philip W. Philbin

A borehole sonde using a 252Cf neutron source and a Ge(Li) gamma-ray detector was field tested in a coal bed in Belmont County, Ohio, to ascertain whether such a device could be useful as a coal-exploration tool. As the sonde was lowered into the borehole, successive spectra were accumulated over short time intervals. The intensities of the capture gamma rays from hydrogen and of decay gamma rays from aluminum were determined simultaneously in each spectrum. A log of the intensities versus depth shows the depth and thickness of the coal bed. With the sonde stationary at points above, in, and below the coal bed, capture gamma rays were measured to show the variation in concentration of certain elements. From the spectrum recorded in the bed, a complete ultimate analysis, the percent ash content, and the heat content were determined without recourse to an external standard. Delayed gamma-ray analyses of the core were also made on the surface in the vicinity of the borehole in a fixed-geometry irradiation facility wing the detector in the borehole sonde. The concentrations of 10 elements were determined by this method on a coal split from the drill core. These experiments show that it is feasible to use a 252Cf- Ge(Li) borehole sonde as an aid in coal exploration.

Jan 1, 1979

By J. B. Newsom

In the Indiana limestone district, some 50 or 60 per cent of the merchantable stone in a quarry opening is waste, and only about 40 or 50 per cent of the stone from the opening is finally sold. So long as the present system of 'quarrying is used, the wastes measured and reported in this paper will continue. Comprehensive development of an entirely different method of quarrying, using wire saws for cutting, promises great improvement. Some of the savings to be expected are pointed out in the following pages. No attempt has been made to measure losses due to variations and natural flaws in the stone, since these vary greatly in different quarries, and accurate measurement would be difficult. The wastes that have been measured account for about 30 per cent of the total ledge, which leaves 20 or 30 per cent chargeable to unmeasured sources of loss. General Causes of Waste There are four general reasons for quarry waste: (1) the structure of the deposit, such as its shape, bedding planes, solution cavities and strain fractures; (2) efforts to quarry blocks which do not contain distinct color or textural variations; (3) the trade custom which permits purchasers to specify the size of the quarry blocks which they will buy, which is a matter of competition for business on the part of stone producers; (4) quarry methods, which cause the greatest amount of waste. Wide channeler cuts, hook holes, crooked splitting and uneven breaking on quarry floors are included in this category. Waste Due to Structure of Deposits The peculiarities of structure cannot be eliminated, but a chance for saving lies in quarrying to take advantage of them. The commercial deposits of Indiana limestone are lenticular masses from 20 to 70 ft. thick, and nearly horizontal. All of these deposits of good stone are in the Salem limestone, a bed in the sub-Carboniferous. The Salem is traversed by two systems of vertical fractures, a major system running from northeast to southwest and a minor system running from northwest to southeast. Where the stone is covered by an over-

Jan 1, 1932

By J. J. Forbes

THE Federal Coal Mine Safety Act (Public Law 552, 82nd Congress) was approved on July 16, 1952. It incorporates, as Title I, the Coal Mine Inspection and Investigation Act of May 7, 1941 (Public Law 49, 77th Congress), which gave Federal inspectors only the right to enter coal mines for inspection and investigation purposes but no power to require compliance with their recommendations. Title II contains the enforcement provisions of the act; its purpose is to prevent major disasters in coal mines from explosions, fires, inundations, and man-trip or man-hoist accidents. At this point a brief account of events that pre- ceded the enactment of the Federal Coal Mine Safety Act seems appropriate. The hazardous nature of coal mining was recognized by the Federal Government as long ago as 1865, when a bill to create a Federal Mining Bureau was introduced in Congress. Little was done, however, until a series of appalling coal- mine disasters during the first decade of this century provoked a demand for Federal action. As a result an act of Congress established a Bureau of Mines in the Department of the Interior on July 1, 1910. The act made it clear that one of the foremost activities of the Bureau should be to improve health and safety in the mineral industries. One of the first projects selected by the small force of engineers and technicians then employed was to determine the causes of coal-mine explosions and the means to prevent them. By investigations after mine disasters the fundamental causes and means of prevention were soon discovered, and the coal mining industry was informed accordingly. However, despite this knowledge and the enactment of State laws and the Federal Coal Mine Inspection and Investigation Act of 1941, mine disasters continued to occur with disheartening frequency and staggering loss of life. The devastating explosion at the Orient No. 2 mine on December 21, 1951, resulted in the death of 119 men. The Orient disaster rekindled the memory of the Centralia, I11., disaster of March 25, 1947, which caused the death of 111 coal miners. These two tragedies ultimately brought about enactment of the Federal Coal Mine Safety Act.

Jan 1, 1954

By David Donoghue

THE. years 1901, 1910, and 1924 may be considered as the beginning of new eras in the history of the oil industry of the Gulf Coast of Texas and Louisiana. Spindletop, in 1901, with its enormous cap-rock production revealed the possibilities of the salt domes. The lateral sand development at Vinton, in 1910, renewed interest in the then known domes which were non-producing, or were producing from the cap rock or from sands above the cap rock. The discovery of three domes, Nash, Orchard and Long Point, in the year 1924, by means of the torsion balance and the seismograph, is the beginning of intensive explorations of the Gulf coastal plain by geophysical methods. Domes other than those mentioned have no doubt been found during the last few months of the year but tests have not been drilled to confirm the evidence of the instruments. DISCOVERY OF DOMES BY GEOPHYSICAL METHODS The Rycade Oil Corpn. operated the first torsion balance on the Gulf Coast in October, 1922, and the Roxana Petroleum Corpn. brought in one of these instruments and began work in December, 1922. The U. S. Coast and Geodetic Survey made some gravity observations at Damon Mound, in 1923, with a pendulum apparatus. In March, 1924, the Marland Oil Co. placed the first seismograph on the Gulf Coast and the Gulf Production Co. followed with one in May. In June, 1924, the Gulf Production Co. began operations with a torsion balance. The Atlantic Oil Producing Co., The Texas Co., and others have experimented with several types of instruments involving various principles. During the next few years, a great advance in geophysical methods may be expected, especially if one of the newly discovered domes should be productive. The first dome discovered was the Nash, in Fort Bend County, Tex., about 6 mi. east of Damon Mound. A slight elevation and two shallow wells containing sulfurous waters made the locality somewhat interesting from the standpoint of surface indications, and the torsion-balance measurements indicated the presence of a dome. On July 20, 1924, the Rycade Oil Corpn. No. 1 Wisdom encountered lime at a depth of 634 ft. and anhydrite at 639 ft. The hole was abandoned on Sept. 8, 1924, at 769 ft. in anhydrite. A cavity in the anhydrite caused much delay and the final abandonment of this test.

Jan 3, 1925

By Joseph Pogue

ANY mechanism, either natural or artificial, for regulating the func-tioning of a given unit in the general economy must operate toward the maintenance of equilibrium if it is to survive. The petroleum industry, concerned as it is with the production of a natural resource of specialized character, is surrounded not only by the economic factors common to other industries but by an extra set of unique elements centering about the fugitive character of crude petroleum under conditions of competitive development. The term equilibrium, therefore, so far as the oil business concerned, involves a combination of economic and physical factors: the first set having to do with supply, demand, costs, profit margins, purchasing power, and the like; and the second, with underground pres-sures in oil pools, efficient rates of extraction, and all other aspects of engineering that may be summarized by the familiar term "conserva-tion." The two categories, in fact, are not as clearly divided as the foregoing statement would imply, for in practice it will be found that the economic and physical aspects have a pervasive interaction and interrelationship. If the development of the petroleum industry in the United States is examined from its inception in 1859 down to the present, it will be found that, beginning about 11 years ago, a new mechanism for regulating the production of crude petroleum made its appearance. Prior to this recent period, the production of this raw material was determined by competitive forces operating without outside restraints. At present the output of crude oil is subjected to supervision by regulatory bodies in most of the oil-producing states, which impose upon the operators certain conditions having to do with the manner and rates of production. Thus, in the space of a decade, the mechanism for producing crude oil has changed from an automatic to a designed procedure called proration. And in its short history this method has been marked by a rapid evolution in its nature and incidence, with progressive changes still under way.

Jan 1, 1938

By Frederick Tickell

PETROLEUM engineers are displaying considerable interest in those fundamental properties of matter and energy that control the phenomena of oil and gas production. The subject is a difficult one to investigate by laboratory experiments for two reasons: (1) it is impossible to reproduce in the laboratory the scale of forces and dimensions that exist in the underground reservoir; (2) if we attempt to scale down the dimensions we are unable to reduce all proportionally. It is as if we tried to construct a model blast furnace for the reduction of iron ore, and reduced all lineal dimensions. We should find that the interstices between the miniature chunks of ore would not .permit rapid transfer of gases, that combustion and heat transfer would not take place as in the full size furnace and that, in short, the contraption would not work. Just so, when we attempt to make a reduced scale oil field we find we must have, not only miniature reservoir and miniature wells, but "miniature" sand, oil, gas, etc. Much valuable work, however, has been done along these experimental lines and more will no doubt follow, but investigators should bear this point in mind and strive to attain dimensional homogeneity and dynamical similarity in order that their conclusions may be translated into terms applying to the oil reservoir. As Gibson says,1 "These conditions are attained when all terms of the physical equation have the same dimensions, . . . when all corresponding particles of the two systems trace out similar paths and when the velocities are such as to make all corresponding forces acting on two such particles in the same ratio. It is the purpose of this paper to discuss the mechanics of fluid movement as it pertains to the oil pool and to point out the complexity of the laws of fluid delivery under the conditions often found.

Jan 1, 1928

By John D. Ridge, Robert C. Barwick

In contrast to international trade in lead, a much larger percentage of zinc shipped from one country to another is shipped in concentrate form. In 1952 international commerce in zinc concentrates accounted for 37 pct of world zinc mine production, and of the total zinc which traveled from one country to another, slightly more than 65 pct was in concentrates. The comparable figures for lead, given in Part VI, were 16 and 27 pct. Of the zinc mined in the world in 1952, 56.6 pct entered international trade; the analogous figure for lead was 57.4. This similarity in proportion of production traded is paralleled by a similarity in sources of exports. The three leading exporters of zinc in all forms in 1952 were Canada, Mexico, and Australia, in that order; the three largest exporters of lead were Mexico, Australia, and Canada. In contrast to the 86 pct theoretical maximum in lead concentrates, the maximum for zinc concentrate is only 67 pct. On this basis alone, it would be reasonable to expect that more zinc would be traded as zinc metal than lead as lead metal. Actually, the reverse is true. Less than 28 pct of the lead in international commerce moves as lead in concentrates, while 65 pct of the zinc so traded is as concentrates. Mexico, a country which has attempted to retain as much metal processing activity as possible within its own borders, has negligible exports of lead in concentrates.

Nov 1, 1955

By Will H. Coghill, Fred D. DeVaney

THE coercimeter, as its name implies, is an instrument for measuring the coercive force[+] of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub- sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. The turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1938

By A. B. Stevens, C. J. Coberly

The absolute porosity of a rock or sand may be defined as the volume of the interparticle space expressed as a percentage of the total rock volume. The effective porosity as contrasted with the absolute porosity is the volume of the interparticle spaces which intercommunicate with passages of sufficient size to permit the entrance or recovery of gas or oil, also expressed as a percentage of the total rock volume. A knowledge of effective porosity is of prime importance in estimating the ultimate recovery to be expected from oil and gas-bearing formations. The determination of the effective porosity of a rock includes the measurement of two values: (I) the volume of the rock as a whole, and (2) the volume of the grains and sealed pore space. This paper deals with a new apparatus which has been called a "hydrogen porosimeter" for determining the volume of the grains and the sealed pore space. This volume is determined by means of the pressure relations established in the instrument by the introduction of a known quantity of hydrogen. The Hydrogen Porosimeter The apparatus used in this work consists of an upper chamber for measuring the gas, a lower chamber for holding the sample to be tested, a gage for measuring the pressures, a tank of hydrogen, and the necessary connections. (Figs. 1 and 2.) Of the several gases that might be used for this work, hydrogen has been chosen for three reasons: (1) it deviates less from the gas laws than most gases; (2) it readily penetrates the sample; (3) it is absorbed less than most gases by the solids and liquids with which it may come in contact. Method of Operation After placing the sample to be tested in the lower chamber, the apparatus is thoroughly flushed with hydrogen to remove all air from the system, which is then brought to atmospheric pressure Po. The valve connecting the two chambers is next closed and the pressure in the upper chamber is brought up to a pressure PI by admitting gas from the tank.

Jan 1, 1933

William B. Phillips, Birmingham, Ala.: The questions raised by Messrs. Wilkens and Nitze are in the highest degree interesting to owners of low-grade iron-ores, aizd no less so to blast-furnace managers. If it can be shown that ores heretofore considered worthless can be brought within the limit of economic use, many large and readily accessible deposits may come into market on the one hand, while on the other the possible increase in the output of the furnace per ton of ore used will prove of advantage to the iron-maker. It cannot, of course, be claimed that this process has been employed on a working-scale with respect to iron-ores, and in so far as concerns results on a large scale no one is any wiser than his fellow. Granting that the results obtained in an experimental way (and certainly the experiments were conducted with a great deal of care) can be attained in practice, we would still be facing the question, what it would cost to get them. In the absence of any specific data, we have to fall back on general principles, helped along, as far as possible, by indications afforded by the experiments. I must confess that as regards the Clinton ores, which I have studied to some extent, I am not sanguine of making a ton of 53 to 54 per cent. concentrates from less than 1.75 tons of 40 per cent. raw ore. It may be possible to get the iron in the heads to 56 to 57 per cent., but the lesser richness of the middlings will probably reduce this to 53 to 54 per cent. in the salable stuff. As the authors remark, it is not worth while to discuss the concentration of the better grades of " soft" Clinton ore; for the price at which they are now delivered at the furnaces, and the comparatively limited amount now remaining, render their concentration unadvisable. If it is to succeed in the Birmingham district, the process must be applied to the low-grade soft and hard ores now con-

Jan 1, 1897

By Grover J. Holt

Open-pit mining on the iron range has been in a stage of transition for several years from the standpoint of mechanization. The most radical change in open-pit mining methods was started in open-pit haulage in 1937 with the departure from the then standard system of locomotive and car transportation and the advent of the heavy duty truck as a replacement. The initial use of trucks was followed shortly by the first installation of a conveyor belt for open-pit ore haulage. The growth of the combination of trucks for gathering units delivering to a conveyor system for transportation out of the pit, has been rapid and this transition appears to have reached a peak in 1949 with locomotives and cars now being used in only a few of the largest open pits. One point which must be considered, if we assume that the maximum equipment change- over point has been reached, is that the largest pits have probably passed their peak of production. Future ore replacement must come from smaller pits wherein the truck conveyor system has done an outstanding job.

Jan 1, 1950

By T. F. Petty

Oil and gas production in North Central Texas has been found in sands and limestones in the Cisco, Canyon, Strawn and Bend series of Pennsylvanian age and in lime of pre-Pennsylvanian age. Production ranges in depth below the surface from 150 to 4500 ft.; a few wells have been drilled to depths in excess of 5500 ft. and penetrated rocks of pre-Cambrian age. In Table 1, the average depth of the pools is shown. No mention, however, is made in this table of approximately 30,000 bbl. of oil produced in Callahan County from a pre-Pennsylvanian pay, presumably the Ellenberger, and an excess of 1,000,000 bbl. of oil produced from limestone, which has been identified as Silurian in the south part of Young County. This well is being produced at the present time. In Table 1 a great many pools of minor importance are listed, which are merely productive spots, and throughout the various producing counties there are numerous similar spots, which might be listed as pools. Their production, however, is listed in the county totals. In Table 2, the totals of the oil wells, gas wells, and dry holes drilled before Jan. 1,1935, include only wells on which records are available to the writer. In Brown, Callahan and Shackelford counties 2924 very shallow wells (150 to 600 ft. deep) have been drilled, on which the record is not available. Possibly there are other wells that were drilled before the district was adequately scouted. No classification as to the depths of this total of 30,644 wells is available at present. Initially, nearly all the oil wells of North Central Texas produced gas, and several areas producing dry gas have been partly developed. A number of casinghead gasoline plants strip the gasoline from the gas produced with the oil, and the manufacture of carbon black is an important industry in Stephens County. Dry and residue gas are marketed through systems serving the various towns of the district, San Angelo to the southwest and the cities of Forth Worth and Dallas to the east. Considerable gas is used in repressuring several pools, the most important of which are the Stover of Brown County and the Cook of Shackelford County. During the past year, 32 gas wells were completed, adding a

Jan 1, 1935

By S. F. Emmons

By far the greater number of the members of this Institute are men who are engaged in the strenuous work of the technical part of their profession, and find little time for the abstract scientific work which is less distinctly practical and pecuniarily remunerative. There is, however, a small but increasingly nu, merous class whose members devote themselves to broad geological problems which underlie the systematic development, and whose work, theoretically, ought to precede and form a basis for that of their more practical brethren. These are the so-called mining or economic geologists, who are, for the most part, connected with State or National geological surveys. Prom the character of their work, the life of these men necessarily follows rather different lines from that of most of their colleagues, and is not generally familiar to them. It seems admissible, therefore, that to the life of a prominent member of this class, who died during the past year, having literally sac-rified his life to his work, a more extended notice should be given than the relatively small number of his contributions to the Transactions night seem to justify. George Homans Eldridge, son of Ellery and Sarah (Mathews) Eldridge, was born on Cape Cod at Yarmouth, Mass.; Christmas day, 1854. His boyhood education in the public school at Yarmouth was followed by a six years' course in the Public Latin School at Boston, from which he entered Harvard University in 1872, being graduated with the highest rank in his class in the natural sciences in 1876. During his college course he spent the summers of 1875-6 at Cumberland Gap, Ky.,as volunteer aid to Prof. N. S. Shaler, who was then in charge of the State Geological Survey of Kentucky. This vacation work, undertaken by him rather as a pastime, gave him his first leaning toward geology. Soon

Jan 1, 1907

By G. S. Brooks

The tendency of the oxides of such metals as aluminum, zinc, chromium, and calcium to form compounds at high tempera tures with iron oxide is well established by past investigation. Data of this reaction, as developed in laboratory research, have been contributed by Burleigh, Hofman, and Wells, in America, and by many others abroad. A partial bibliography of the subject is appended. From these authorities we learn that the ferric oxide here has the function of an acid, giving in the case of ZnO a zinc ferrite, with a normal composition of ZnOFe2O3 This formation of zinc ferrite particularly affects the success of such processes as leaching or magnetic separation, and thus becomes practically important to the metallurgist. But the meager existing data do not entirely agree; and quantitative results from muffle-practice are conspicuously absent. Furthermore, it being of some general importance to the zinc smelter in both roasting and reduction, the following few notes of operations oil a commercial scale are contributed: I. Physical Properties of Zinc Ferrite. As formed for the most part synthetically by investigators, zinc ferrite exhibits characteristic physical properties, such as octahedral crystals, dark color, and a density over 5, together with a slight magnetic attractability. In examining with the microscope many products of mechanical muffle-roasting kilns, it is, however, impossible to find individual grains which can be identified as consisting entirely of zinc ferrite. The variety of colors, especially where each grain of blende was mechanically free from marcasite, rather conveys the impression of a partial ferritization of the grain. One side or end, for example, may often have the hard, dense surface and dark red to black color of the ferrite, while the balance shows the usual light yellowish brown of a normal iron-free blende.

Jan 1, 1914

By Alfred Beasley

LEAD-REFINING practice at the. Bunker Hill differs to some extent from that of other United States refineries using the Parkes process, in that the Bunker Hill-has reverted to a custom used years ago of making two kinds of skims, or crusts, in the desilverizing kettles. Also, this was the first refinery to adopt the liquation process for silver skims as developed in Australia. Both of these ideas were brought to the attention of the operator by H. S. J. Sommerset, in the summer of 1924, while he was visiting metallurgical plants in the United States, when he was general superintendent of the Broken Hill Associated Smelters Pty., Ltd., of Port Pirie, South Australia. Since Mr. Sommerset's visit, United States patents on the liquation process have been issued to George Kenneth Williams, of Port Pirie, South Australia. At the Bunker Hill, the lead bullion is conveyed from the blast furnaces to the refinery in brick-lined cast-steel pots, each having a capacity of 5 tons, by a 20-ton electric crane, to which is suspended a Fairbanks-Morse suspension-type scale on which the gross, tare and net weights are obtained. The bullion is poured from the small bullion pots into either one of two kettles of 105 tons capacity, and when a kettle is entirely filled the heavy dross is removed by skimming it into a 5-ton pot suspended by the crane. The crane operator becomes proficient in the manipulation and a kettle is skimmed in a very short time. After the kettle is skimmed clean the bullion is pumped to a kettle of the same size alongside, where the bullion is cooled until it has almost frozen. By using two kettles for the drossing operation, one to accumulate the bullion where the heavy dross is removed, and then pumping to a clean kettle comparatively free of hangings, etc., it is possible to reduce the copper content much lower than if only one kettle is used in the operation. The average yearly analysis of bullion is given in Table 1.

Jan 1, 1930

Jan 1, 1942

By Cheri Eby, William R. Eby

This paper describes the state-of-the-art of pneumatic transport systems that are capable of conveyinq waste cuttings generated by raise drills during shaft construction projects. Additionaly other examples of applications pertaining to pneumatic transport systems qualified to convey abrasive and nonabrasive materials (&., gravel, shale, coal, ore, and limestone) will be presented.

Jan 1, 1982

Jan 1, 1958

By John Wulff, Richard P. Seelig

The importance of the pressing operation in the forming of articles by powder metallurgy depends to a great extent on the type of product to be made. While in some few cases the pressing is merely a means of compacting loose powder particles into a solid mass preliminary to a sintering treatment, in most applications it constitutes a molding operation with the purpose of shaping the raw material in powder form into a certain predetermined, accurately defined part not altered in shape by subsequent sintering. In still other cases, no pressing at all but sintering in molds gives useful articles. A limited number of products are made by the simultaneous application of pressure and heat. The factors that control the product of the pressing operation are raw material, lubricant, type, size and shape of die and compact, magnitude and time of application of pressure, as well as temperature of pressing. All such factors need to be controlled; yet, depending on the function of the pressing operation, greater emphasis may be placed on processing factors other than the pressing operation. In any complete discussion of pressing, subsequent sintering cannot be disregarded. For the sake of brevity, the present paper has been limited to the mechanics of pressing and only occasionally refers to sintering. For the same reason, hot-pressing has been omitted as beyond the scope of this paper In any survey of the literature on the pressing of metal powders, the 1938 paper of Balshinl on the theory of the process of pressing deserves mention. The first attempts at an interpretation of pressing phenomena were made by Balshin' and RakovskL2 The experimental results of both are of great interest. Since the experimental results are not described, the work was repeated, using our own interpretation of the possible techniques, and is reported in the following pages. The basic theory of Balshin,' based on a hydro-dynamic analogy, however, leads to hut another way of plotting density and pres- , sure against height of a pressed compact. Since it does not give any new insight into the phenomena, nor account for the influence of side-wall friction, a discussion of the theory has been omitted from this paper. Density Gradients in Compacts The process of pressing metal powders in a die (disregarding for this consideration the powder filling and ejection operations) may be divided into three phases: (I) packing, (2) elastic and plastic deformation, (3) cold-working with or without fragmentation. It must be emphasized that these three steps do not follow each other in sequence; on the contrary, in practice

Jan 1, 1946

By John Wulff, Richard P. Seelig

The importance of the pressing operation in the forming of articles by powder metallurgy depends to a great extent on the type of product to be made. While in some few cases the pressing is merely a means of compacting loose powder particles into a solid mass preliminary to a sintering treatment, in most applications it constitutes a molding operation with the purpose of shaping the raw material in powder form into a certain predetermined, accurately defined part not altered in shape by subsequent sintering. In still other cases, no pressing at all but sintering in molds gives useful articles. A limited number of products are made by the simultaneous application of pressure and heat. The factors that control the product of the pressing operation are raw material, lubricant, type, size and shape of die and compact, magnitude and time of application of pressure, as well as temperature of pressing. All such factors need to be controlled; yet, depending on the function of the pressing operation, greater emphasis may be placed on processing factors other than the pressing operation. In any complete discussion of pressing, subsequent sintering cannot be disregarded. For the sake of brevity, the present paper has been limited to the mechanics of pressing and only occasionally refers to sintering. For the same reason, hot-pressing has been omitted as beyond the scope of this paper In any survey of the literature on the pressing of metal powders, the 1938 paper of Balshinl on the theory of the process of pressing deserves mention. The first attempts at an interpretation of pressing phenomena were made by Balshin' and RakovskL2 The experimental results of both are of great interest. Since the experimental results are not described, the work was repeated, using our own interpretation of the possible techniques, and is reported in the following pages. The basic theory of Balshin,' based on a hydro-dynamic analogy, however, leads to hut another way of plotting density and pres- , sure against height of a pressed compact. Since it does not give any new insight into the phenomena, nor account for the influence of side-wall friction, a discussion of the theory has been omitted from this paper. Density Gradients in Compacts The process of pressing metal powders in a die (disregarding for this consideration the powder filling and ejection operations) may be divided into three phases: (I) packing, (2) elastic and plastic deformation, (3) cold-working with or without fragmentation. It must be emphasized that these three steps do not follow each other in sequence; on the contrary, in practice

Jan 1, 1946