Search Documents

Executive SCOTT TURNER, Chairman FREDERICK M. BECKET JOHN A. MATHEWS H. A. GUESS WILLIAM WRAITH Finance HENRY KRUMB, Chairman PAUL D. MERICA ROBERT E. TALLY Admissions JOHN M. LovEJOY, Chairman GEORGE D. BARRON ERLE V. DAVELER WILLIAM H. BASSETT W. D. B. MOTTER, JR. Alternates HENRY B. FERNALD F. JULIUS Polls AMOR F. KEENE

Jan 1, 1932

By Kenneth F. Whinery, John M. Campbell

Basically, the Buckley-Leverett theory involves two systems which are similar in nature but are differentiated by time. These systems may be described by the fractional flow and frontal advance equations which essentially characterize the mechanics of oil movement while being expelled from the reservoir. The fractional flow equation originally developed by Leverettl may be expressed in the more usable form The development of this equation is based on Darcy's law describing fluid flow through porous media and applies to the flow at only one point (it is a point function). For simplification, the fractional flow equation is written in the above form because the capillary forces always increase the fractional flow of the displacing phase regardless of the direction of flow or the displacing phase. If, for simplicity, the effects due to gravity and capillary pressure differences are neglected, the fraction of the displacing fluid, f, at any point in the flowing stream is related to the properties of the system by 1 Thus, it is seen that in the absence of capillary and gravitational effects, fd for a given sand and fluids varies only with saturation and pressure. The magnitude of the viscosity ratio, —a has an effective range (range of about 30) in the system where gas is displacing oil and a much smaller range for water displacing oil. In order to make the fractional flow equation more versatile, it is necessary to connect the fractional flow at a given point and saturation with time. This problem was approached by Buckley and Leverett" who developed the frontal advance equation, Eq. 3 states that the rate of advance of a plane that has a fixed saturation, Sd, is proportional to the change in composition of the flow stream caused by a small change in the saturation of the displacing fluid. It is, essentially, a transformation of a material balance equation representing the net rate of accumulation of the displacing phase within a homogeneous sand block. This accumulation is proportional to the difference between the rate at which the displacing fluid enters the sand and that at which it leaves. Eq. 3 describes the velocity with which a plane of constant displacing phase saturation advances through a porous system. Buckley and Leverett," Babson,' Kern," Welge, and others have adequately discussed the basic mechanism and application of the fractional flow and frontal advance equations. APPLICATIONS OF THE FRONTAL ADVANCE THEORY TO PETROLEUM RECOVERY Two general applications of the Buckley-Leverett frontal advance theory involve the system in which the oil is being displaced by an expanding gas cap overlying the oil zone and that in which the oil is being displaced by water. Displacement by Gas in the Presence of an Immobile Water Saturation A system in which gas is the displacing phase may be thought of as having two forces effecting the displacement process. These forces are the gravitational force and that force exerted by the displacing gas. The gravitational effects control the displacing efficiency of the gas. The gravitational effect will be less at higher rates of flow, thereby reducing the effectiveness of the displacement of the oil by the gas. The more efficient displacements occur at flow rates which are less than the gravity free fall rate. Capillary forces can be neglected without materially changing the magnitude of the gas saturation. The Mile Six pool is used herein to illustrate the calculating procedures in evaluating gas drive-gravity drainage field perfomlance. These calculations represent the determination of the gas-oil contact when the distribution of the hydrocarbon pore volume is considered. Two methods

By Donald J. Knight

HEAT Treatment at 1500' F of a mild steel containing 0.1 pct C, in an atmosphere which is oxidizing to both carbon and iron, results in the progressive oxidation of the metal surface with little or no change in the carbon content of the underlying metal. Further heat treatment of the scaled metal in either a neutral atmosphere or in a vacuum may or may not result in the decarburization of the metal depending upon the physical nature of the scale. It is apparent that if a continuous layer of oxide is present on the steel surface, the reaction OScale + Cmetal Cogas cannot progress since the SO formed gas would be unable to leave the oxide/metal interface. Thus, in order for the reaction to progress, the oxide must be cracked or porous. Vacuum heat treatment at 1500" F of samples with a thick continuous oxide scale showed no decarburization of the steel. However, when cracks were introduced mechanically into the scale prior to the vacuum heat treatment notable decarburization of the metal resulted and a structure as shown by Fig. 1 obtained, i.e., reduction of the crack walls to ferrite. With reference to the diagram of Fig. 2, it would appear that a mechanism of the following type takes place. Carbon atoms arriving at an oxide/metal/void interface, such as 'A', Fig. 2(a), can combine with oxygen atoms from the scale and leave the reaction site as Cogas thereby reducing the oxide to metal. On a greatly magnified scale, Fig. 2(b),this will appear as a ferrite projection along the crack wall. Carbon atoms entering this projection can react with oxygen atoms at point 'C', which is a new interface, and so on leading to a progressive growth of the ferrite along the crack wall and to the surface, Figs. 2 (c) and 1. It would appear that the only means by which thickening of the ferrite film can take place is by a diffusion of oxygen through the ferrite film to react with carbon at the newly formed ferrite/ void interface. Since the diffusion rate of carbon is reportedly much greater than that of oxygen, and since there is a low probability factor of oxygen and carbon atoms arriving simultaneously at the same site on the ferritehoid interface, there will be a tendency for more rapid lengthening than thickening of the ferrite layer, as is observed.

Jan 1, 1962

By JAMES GAYLE

(Presented at the Washington meeting, May 3, 1905, and simultaneously sent to the Iron and Steel Institute, for presentation at the meeting of that Society in London, May 11, 1905.) IT is to be regretted that the data respecting the use of dry-air blast, which was presented to the Iron and Steel Institute at its meeting in the United States, in October, 1904, should. have been restricted to the period from August 25th to September 9th inclusive, and from September 17th to 30th inclusive. In order to present the paper at all it was found necessary to limit the record of operations to the period above stated. In the discussion of the paper it would appear from the conclusions of some participating therein, that they have been placed at some disadvantage in considering the economies obtained through the use of dry-air blast, by reason of the data covering such a short period. It is the purpose of this communication to present in detail the record of operations of the Isabella Furnaces from November, 1904, to March, 1905, inclusive, as shown by the furnace-records. The month of October, 1904, is not included, as the furnace using dry-air blast was stopped several times for repairs, and while the record was a very good one considering these interruptions, yet it was not a continuous one. The record for Furnace No. 1 using dry-air blast, and the comparison with Furnace No. 3 using natural air for the month of November, 1904, is set forth in Table I. By a reference to my former paper it will be noted that the month of November is the beginning in this country of the winter period, when the atmosphere decreases rapidly in humidity. The month of October being the transition month in the autumn and April in the spring, and furnaces using natural air approach more closely, from November on, to the conditions obtained by the use of dry-air blast. The data given in

Jul 1, 1905

By J. E. Pavlick, W. W. Mullins, H. W. Paxton

The growth of nitrogen-austenite during nitriding of large-gvained ferrite between 650" and 800°C has been studied as a functimz oJ time and nitrogen potential of the atmosphere for a variety of alloying elements dissolved in the ferrite. Whereas no preferential grain boundary penetration by aistenite takes place in zone-refined iron, the addition of aboit I zot pct oj' V, Ti, Cr. Si, or A1 produces significant protrusion of austenite down former 0-0 boundaries. This group of elernents also produces ragged y-0 interfaces in the a grains which advance more slozuly than those in zone-refined iron. 1 zut pct of Ni, Co, Mn, or Mo dissolved in ferrite leads to essentially smooth 7-a interfaces, which advance at rates very sinzilar to those in zone-refined iron. The reasons for this effect are not clear. Two possible limiting hypotheses, not necessarily exclusive, are discussed. One involves p.referentia1 grain bozindary diffusion of nitrogen. the other the production of a zone of ferrite, stpersatcirated with respect to nitrogen, from which austenite precipitates helerogeneozisly on the a-a gyain boundaries. In many phase transformations which occur by nu-cleation and diffusion-controlled growth, information on the parameters which control the rates of nuclea-tion and of growth is frequently not quantititative. The present work describes a continuation of efforts to obtain quantitative data on growth rates in systems where thermodynamic and kinetic factors are known independently, and thus where comparison with models of the growth process is possible. The work has been conducted on iron-base systems for two reasons. Firstly, there are several interesting transformations in this system, many of which are of practical importance. Secondly, the information on phase diagrams, activities, and diffusion coefficients is more complete in this system than in any other. These data are still inadequate to check all the effects of alloying elements, but at worst it is possible to make estimates and thus examine order-of-magni-tude agreement with proposed models. It will be necessary to do this in the present work. The problem studied was the growth of nitrogen-austenite in from the surface of large-grained columnar crystals of alloyed ferrite exposed to an NHs/Hz atmosphere. Earlier work by Grozier et al.' had suggested that growth of austenite may occur preferentially along grain boundaries of alloyed ferrite, whereas zone-refined (ZR) iron shows no such effect, Fig. 1. Growth of nitrogen-austenite into single crystals of zone-refined ferrite is planar provided sufficient nu-cleation sites for austenite are present, and is controlled by volume diffusion of nitrogen through the

Jan 1, 1967

Jan 1, 1969

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth, W. L. Finlay

Titanium with up to 7.5 pct Al forms single-phase a alloys that are work hardening, not heat treatable, and ductile as welded. The high aluminum Y phase alloys are not usefully ductile, despite their low hardness, but they have excellent oxidation resistance and hot hardness. LITTLE has been published on the effect of aluminum on the mechanical properties of titanium, despite the fact that two of the first four commercial alloys released by titanium alloy producers contained aluminum as an important alloying ingredient. These were both a-ß type alloys, one containing 4 pct A1 and 4 pct Mn and the other containing 3 pct A1 and 5 pct Cr. However, neither of these alloys reflects the true alloying nature of aluminum, since each contains important amounts of the ß-stabilizing addition, manganese or chromium. In a previous publication on the constitution of Ti-A1 alloys,' the authors showed that aluminum had a high solubility in a titanium and was strongly a stabilizing in nature. About 25 wt pct A1 is soluble in a titanium at room temperature. With as little as 5 pct added aluminum, the a transus temperature is increased from 882" to 970°C, and the correspond- ing ß transus to 995°C. The first intermediate phase in the Ti-A1 system is the ordered face-centered tetragonal TiAl phase, which extends from 34 to 46 wt pct Al. The present paper presents hardness data over the entire titanium-rich region of the system, through the TiAl phase, and mechanical property data on the alloy range capable of being fabricated. Methods of Investigation The materials used and general preparation of alloys, as well as experimental techniques used in the investigation of Ti-A1 alloys, have been adequately described.' Briefly, the preparation consisted of arc-melting the desired amount of high purity aluminum (99.99 pct purity) and iodide titanium (maximum hardness 100 Vickers, as deposited) together on a water-cooled copper hearth under a partial pressure of argon. The resulting button ingot was of such form that it could be fabricated without further treatment. All work was done using ingots weighing 10 to 15 g, which were hot-rolled to strip form whenever possible. Tensile samples were 3.25 in. long, 0.5 in. wide, and 0.040 in. thick, with a reduced section 1.25 in. long by 0.250 in. wide. The gage length used was 1 in. Electrical strain gages mounted on the

Jan 1, 1954

Jan 1, 1967

By Joklik, G. F.

Most publicity about the copper industry nowadays is focused on the adequacy of ore reserves and on excessive mining capacity. These concerns, stemming from public awareness of actual and potential shortages and oversupplies, relate to production rather than consumption. Perhaps the reason for this one-sided view is that copper is thought of as a commodity which is conspicuously traded in world markets, rather than as one of many industrial materials that serve today's rapidly changing technology. Copper differs from other widely traded commodities in that its real cost of production has progressively increased since World War 11. The reasons for the increase are identifiable by analyzing operations in one of the world's large producing centres, the copper province of Arizona. Another respect in which copper differs from some other commodities is that increases in demand occur less automatically in the case of copper than they tend to in commodities whose consumption is more directly related to population growth. The copper industry's current inability to generate and attract needed investment capital is attributable to these differences between copper and other commodities; it suggests that the concept of copper purely as a commodity is outdated. The key to the problem is better integration between the activities of copper producers and users. Depending on circumstances, integration takes various forms- for example, investment tied to long-term sales con- tracts between producers in developing countries and consumers overseas; common ownership of producing and manufacturing facilities in industrialized nations like the U.S.; and consumer-oriented research and marketing by the copper producers.

Jan 1, 1978

By B. E. Terkelsen, B. J. Piearcey

A study has been made of the effect of unidirectional solidification on the creep behavior, stress-rupture properties, and thermal shock resistance of four nickel-base superalloys. The alloys Mar-MZOO, B-1900, IN 100, and TRW 1900 show improved rupture ductility and thermal shock resistance when tested with the columnar grains parallel to the major stress axis during test. The relative improvement in creep-rupture properties depends on the intrinsic strength of the alloy, a property which depends on composition, heat-treatnient, and crystallographic orientation. The data clarifies some of the factors affecting the properlies of the cast nickel-base superalloy. COMPONENTS designed for high-temperature use have, in recent years, been fabricated by precision casting techniques using nickel-base alloys developed specifically for use in the conventionally cast condition. This development was a result of both the increasing complexity of the component and the recognition that high-temperature strength was incompatible with workability. The use of castings can be economically favorable, but, more important, the recent complex designs of air-cooled gas turbine blades and vanes in alloys which possess the necessary high-temperature strength cannot be forged. Common modes of failure of high-temperature components are excessive creep, creep rupture, and thermal fatigue. If rupture occurs then the mechanism is usually by inter crystalline cracking along those grain boundaries oriented transverse to the major stress axis. In the stronger alloys, rapid propagation of intercrystalline cracks result in apparent premature failure demonstrated by the absence of third stage creep in a creep-rupture test and low rupture ductility. Tensile ductility shows a similar trend, that is, decreasing ductility with increase in strength. It is not surprising, therefore, that increases in creep strength have only been obtained with a loss in resistance to thermal shock, a property which shows a dependence on tensile ductility. VerSnyder and ~uard' showed that the application of unidirectional solidification to a brittle Ni-Cr-A1 alloy both improved the rupture life of the alloy and increased rupture ductility. Since this casting method results in columnar grains, it appeared that the solution to the lack of ductility in nickel-base alloy components was the elimination of the source of failure, namely the transverse grain boundaries. This concept was recently developed2 to produce cast-to-size gas-turbine blades and vanes consisting entirely of columnar grains oriented parallel to the major stress axis of the component. Not only did the process impart increased rupture life and ductility to the components, but it also increased their resistance to thermal shock. During this development, the effect of unidirectional solidification on the properties of several alloys was investigated. The resulting data allows certain conclusions to be drawn regarding the factors affecting the creep and stress-rupture properties of the cast nickel-base superalloy and also its resistance to thermal shock. Detailed information was obtained on the alloys Mar-MZOO, B-1900, In 100, and TRW 1900. The composition of the alloys studied are shown in Table I. MATERIAL PREPARATION AND TESTING The conventionally cast alloys are cast as +-in.-diam bars in innoculated shell molds under conditions designed to maintain control of grain size. Unidirec-tionally solidified casting were produced in the form of 3-in.-diam ingots. Specimens from the latter were machined such that the axes of the columnar grains were parallel with the axis of the test bar, except in certain cases where the transverse properties of the material were being evaluated. The specimens were tested in an axial loading creep machine.' Temperatures were measured with thermocouples, attached just outside each end of the gage length, to assure uniform temperature along the entire specimen. Chromel/alumel thermocouples were used up to 1800"F and Pt/Pt-10 pct Rh thermocouples above 1800"F. The specimen temperature was recorded and maintained within i2"F throughout the test. Creep extensions were measured automatically with extenso-meters attached to ridges on the specimen and recorded continuously using linear variable differential transformers and multipoint recording equipment. MICROSTRUCTURE The microstructures of transverse sections of the four alloys studied are shown in Figs. 1 and 2. Fig. 1 shows optical micrographs of the alloys, both in the conventionally cast and unidirectionally solidified conditions. Each alloy displays a cored dendritic structure, a distribution of MC carbide, and the presence of the y — y' eutectic constituent.~ In the case of IN 100 and B-1900, Fig. 1 indicates that in these specimens the eutectic is degenerate. That is, it consists only of y' pools indicating that the y constituent has been solutioned during the cooling period after solidification. The major effect of unidirectional solidification on the microstructures of the alloys is a tendency to promote a more dendritic form of MC carbide and an increase in dendrite arm spacing, both effects being a result of the slower solidification rate in the unidirectional solidification technique. V, lec tron micrographs of transverse sections of the four alloys in the two cast conditions are shown in

Jan 1, 1968

By P. B. Baxendell

The appraial of producing properties and profitability ntzalysis of a proposed capital expenditure are based on the same principles. In both problems a projection of future cash income is. cornpared to one or more capital expenditures. Several different methods have been in use either to compute a price to obtain a given earning power on the investment or to compute the earning power which will result from a given capital expenditure. One of these, the "Average Annual Rate of Return" method, computes in a simple manner the ratio of the present value of the future earnings after amortization to the present value of the undepreciated balances of the investment over the life of a project. This method, not well known generally, appears to have some rather unique advantages in reducing the computation work required, eliminating trial-and-error solutions, and providing a more accurate answer when applied to oil industry investments subject to the unit-of-production basis of amortization. Its derivation is given and its versatility demonstrated in the solution of certain everyday investment problems. A number of charts, useful in applying this method to profitability analysis and appraisal work, are provided. The current trend in the market values of producing properties is shown. INTRODUCTION Making sound capital expenditure decisions requires an objective means of measuring the productivity of individual investment proposals. Since the best measure of the economic worth of such proposals is their ability to produce profits, it is common practice to grade proposed capital expenditures according to their annual earning power as a percentage of the outstanding capital. The same principles which govern the determination of the rate of return of proposed capital expenditures also apply generally to the problem of determining the appraisal value or purchase price of income-producing oil and gas properties. Both problems are of prime importance in the producing phase of the oil business, where management is faced daily with decisions to drill or not to drill certain development wells, or with the determination of the appraisal value of producing properties. The common feature in both problems is that a projection of future cash income is compared with a known or estimated capital investment to determine itsiearning power or annual rate of return. In the case of development drilling, the cost of the proposed well can usually be estimated with a fair degree of accuracy and the problem consists of finding the rate of return on the invested capital. In the case of appraising producing properties, on the other hand, the desired rate of return is usually known in advance and the problem consists of determining the purchase price which, for the given income projection, results in the fequired rate of return. Certain accounting procedures common to the oil and gas producing business make these two problems and their solutions somewhat different from corresponding problems in other industries, and, in certain ways, simpler. The main difference is in the amortization policy which, for oil and gas production, is frequently on a unit-of-production basis, compared to the amortization on a time basis used in many other industries. The purpose of this paper is to discuss briefly the various methods currently in use for the measurement of productivity of invested capital in producing properties and, in more detail, the derivation and application of what will be called the "Average Annual Rate of Return Method". This rather interesting and not too well known method has some very definite advantages in the solution of many problems common to the oil industry. For the sake of simplicity, federal income tax considerations have been disregarded in the examples used, since they do not affect the principles involved. The use of the production payment route in the sale or purchase of producing properties, which has been amply covered in many other publications, has also not been included in this analysis. METHODS FOK MEASUKING THE EARNING POWER OF INVESTED CAPITAL, Of the many different methods used to measure the earning power of invested capital, four are applicable to oil or gas production ventures. Depending on whether these four methods utilize one or two interest rates, and whether a fixed amortization pattern is used, they may be classified as follows.

By Richard Hamburger

Calculating machines permit the use of the more rapid cotangent and semigraphic solutions of plane triangulation. The results of these methods are as accurate as those of other methods. Simple adjustment of the net, and ease of calculation encourage more complete field work. Errors in field work or in computation are easily localized.

Jan 1, 1950

By Antoni Kidybinski

Mechanical properties of the nether roof rocks play a substantial role in maintenance of mine openings. On longwall faces too low strength is a cause of rock- falls which bring about delays in face advance, and hazard to the miners, while too high strength may result in over hanging of roof rocks in gobs, sometimes over a large area, initiating dynamic periodical pressures. Hence, efforts have been undertaken to develop methods of caveability evaluation for proper selection of roof control system and of longwall-face supports. DESCRIPTIVE CLASSIFICATIONS One of the basic qualitative criteria for classification of roof types with different caveability is the criterion of geological structure. The 26-stages scale worked out for conditions of Donetz Coalfield. USSR, by E.T. Proyavkin et al.(l) may be an example of that type of classification. This scale is presented graphically in Fig. 1. The first types of roofs according to this scale are easily caving immediately after exposure of a small surface, while the last be- long to the strongest roofs which over-hang in waste and require artificial fracturing. Observations and measurements carried out also in Donetz mines lead W.T. Davidyanc (2) to following classification: Class I - weak and densely bedded rocks very easily caving after each advance of supports. The roof subsidence over a waste edge is: [ ] where: h is roof subsidence, m M is thickness of the seam being mined, m S is width of an opening, m Class II - medium caveability and small main roof movements [ ] Class III - hardly breakable rocks, thicker beds with higher strength: caving by large blocks. After exposure of larger roof surfaces the movements of the main roof strata may affect an opening. [ ] Class IV - very hardly breakable rocks - thick, monolithic sandstones: they cause considerable difficulties in working with caving. [ ] Class V - thin-bedded rocks featured by the capacity of a smooth subsidence without disintegration into loose blocks with keeping contact between the particular blocks in a bed. In this classification mining with full roof caving is recommended for class I-III and only exceptionally for class IV. In many coal fields, qualitative and quantitative observations of roof rocks behavior have been carried out: as a result relations and characteristics found in certain mines are given. As an example, Kizielov Coalfield data in the USSR given by B.S. Vinokur (3) may be mentioned. In working thin pitching seams man- less system of undercutting the seam by means of rope saw is used there. The author separated four classes of roofs and gave, for every class, the empirical relation between the extracted area and the time of roof stability. The size of the stable area of exposed roof for particular classes is as follows: 120 to 150 m2 (1291 to 1614 ft2 ), 170 to 200 m2 (1829 to 2152 ft2), 250 to 280 m2 (2690 to 3013 ft2 ) and 350 to 400 m2 (3766 to 4300 ft ). For Kuznetz coalfield in the USSR the following classification of roofs was developed at the WIMI Institute in Leningrad: Class I - completely unstable: impact strength in- dex of rock f = up to 1.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide, exposed after shearer's cut holds stable during the time not longer than 5 min. Class II - low stability: f = 1.5 to 2.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and up to 4.0 m (13 it) long, exposed after shearer's cut holds stable during 5 to 20 min. Class III - medium stability: f = 2.51 to 3.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide and 4.0 to 25 m (13 to 82 ft) long, exposed after shearer's cut holds stable from 20 min. to 2 hours. Class IV - stable: f = 3.51 to 4.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and 25 m (82 it) long exposed after shearer's cut is stable during the time longer than 2 hours. Class V - entirely stable: f = over 4.5

Jan 1, 1982

We would like to thank Mr. Mandolesi for his informative paper on rails from strand cast steel. The chemical and structural properties of the strand cast steel were of particular interest to us. We would like to supplement his excellent report with some of Inland's findings from our Caster with submerged nozzles and strands reduced in line from 7" x 7" to 5-5/8" square cross section. Inland has conducted extensive segregation studies on AISI 1049 steel - Fine Grain 0.50% carbon and 0.75% manganese. Based on approximately 80 heats, our normal segregation pattern results in analyses of .49% carbon in the center, and 0.50% carbon at the midway and edge position. The sulfur analysis averages .025% in the center, .027% midway, and .026% at the edge. Note the slight negative segregation between the center and midway position. This steel, being lower carbon and probably cast nearer the liquidus, resulted in less segregation than the 0.80% carbon rail steel.

Jan 1, 1972

By Ogden Tweto

The Leadville district, on the west flank of the Mosquito Range in central Colorado, has produced silver, zinc, lead, gold, and minor metals valued at $512,000,000. The ore deposits are in a sequence of dolomites and quartzites, Cambrian through Mississippian in age and about 500 feet thick, which is extensively intruded by porphyry sills, dikes, and plugs of Tertiary age. The sedimentary rocks and sills dip about 15°E and are broken by many faults, which are predominantly of nearnorth trend and downthrown to the west. The ore deposits are principally blanket or manto replacement deposits, but in the eastern part of the district many veins occur also. The replacement deposits are largely confined to three dolomite units in the stratigraphic sequence. Of these, the uppermost or Leadville Dolomite is the most productive. Most ore bodies are on the underside of porphyry sills and, particularly, beneath sills that occupy unconformities. Many replacement bodies have vein roots or branch from veins. The veins occupy faults and are productive mainly in the section of quartzites and dolomites and included sills. The primary ores consist principally of pyrite, marmatitic sphalerite, and galena but locally contain chalcopyrite, silver minerals, bismuth minerals, and gold. Principal gangue minerals are manganosiderite and jasperoid. The ore deposits have a crude zonal pattern centered around an intrusive center at Breece Hill, which evidently influenced ore deposition thermally. The ore deposits were oxidized to depths of several hundred feet in Miocene time. Bonanza ores mined in the early days were characterized by cerussite, cerargyrite, and embolite. Later, zinc carbonate ores were identified and mined on a large scale. The Leadville district is a complexly faulted and intruded area at the intersection of major fault systems trending N20°W and N15°E in the Mosquito Range. The intensely fractured area evidently localized igneous intrusion and subsequent mineralization. Ore solutions rose on many of the faults in the area, presumably from the same source as the porphyry magmas. Movement on these faults continued into the Pleistocene, displacing ore bodies, oxidation zones, Pliocene sediments, and glacial deposits.

Jan 1, 1968

By Shiou-Chuan Sun

DISCUSSION shiou-chuan sun (author's correction) - Too late for revision, the author realized that the data on stability of froth presented in this paper were not based on the same height of froth column. It is recommended herein that the stability of froth is better calculated by dividing the time elapsed until the froth disappeared by the volume (in cu cm per sq cm) or height of the froth column, and is expressed in sec per cm. The stability data in Tables I, II, and III of this paper were recalculated, in accordance with this recommendation, and the results are shown respectively in the accompanying Tables VII, VIII, and IX. Compared with Tables I, II, and III of the paper, the stability data of Tables VII, VIII, and IX are more reliable in disclosing the persistence of froth of various frothers having different frothabilities. For example, the conclusion given in the paper that the stability of froth is generally proportional to the volume of froth becomes invalid when the stability of froth is expressed in sec per cm, as shown in Tables VII, VIII, and IX. Table VII shows that both the stability and volume of froth increase with the addition of small amounts of n-hexyl alcohol, and that further additions of n-hexyl alcohol decrease the stability but increase the volume of froth. Table VIII indicates that the stability of different types of frothers is governed by their chemical composition and is difficult to predict from their frothability. Table IX shows that the stability of different frothers with similar nonpolar groups tends to increase with a decrease of the hydro- philic property of their polar groups, and consequently with the decrease of their solubilities. This is further substantiated by the fact that the stability of frothers, as listed in Table IX, is generally lowered by the solvent effect of absolute ethyl alcohol. Table IX shows also that the stability of froth tends to increase with the decrease of the volume of froth* provided the frothers used have similar nonpolar groups and dissimilar polar groups.

Jan 1, 1953

By Shiou-Chuan Sun

DISCUSSION shiou-chuan sun (author's correction) - Too late for revision, the author realized that the data on stability of froth presented in this paper were not based on the same height of froth column. It is recommended herein that the stability of froth is better calculated by dividing the time elapsed until the froth disappeared by the volume (in cu cm per sq cm) or height of the froth column, and is expressed in sec per cm. The stability data in Tables I, II, and III of this paper were recalculated, in accordance with this recommendation, and the results are shown respectively in the accompanying Tables VII, VIII, and IX. Compared with Tables I, II, and III of the paper, the stability data of Tables VII, VIII, and IX are more reliable in disclosing the persistence of froth of various frothers having different frothabilities. For example, the conclusion given in the paper that the stability of froth is generally proportional to the volume of froth becomes invalid when the stability of froth is expressed in sec per cm, as shown in Tables VII, VIII, and IX. Table VII shows that both the stability and volume of froth increase with the addition of small amounts of n-hexyl alcohol, and that further additions of n-hexyl alcohol decrease the stability but increase the volume of froth. Table VIII indicates that the stability of different types of frothers is governed by their chemical composition and is difficult to predict from their frothability. Table IX shows that the stability of different frothers with similar nonpolar groups tends to increase with a decrease of the hydro- philic property of their polar groups, and consequently with the decrease of their solubilities. This is further substantiated by the fact that the stability of frothers, as listed in Table IX, is generally lowered by the solvent effect of absolute ethyl alcohol. Table IX shows also that the stability of froth tends to increase with the decrease of the volume of froth* provided the frothers used have similar nonpolar groups and dissimilar polar groups.

Jan 1, 1953

Jan 1, 1967

By M. R. J. Wyllie, Michael A. Torcaso

With the continued deep drilling of today, increasing numbers of high pressure and high temperature gas-condensate reservoirs are being discovered. Correspondingly, the ranges of properties of gas-condensate reservoir fluids are also being increased. The literature1*'." contains several excellent reviews of the property ranges in presently known condensate reservoirs. When one examines these property ranges, it becomes apparent that the need for reliable data is great if the engineer is to evaluate properly or appraise a gas-condensate reservoir. It is the purpose of this paper to present phase-behavior data that will point out some of the important variables that influence recovery from gas-condensate reservoirs produced by pressure depletion. All these variables may be resolved into two major categories: the hydroc:arbon composition of the reservoir fluid and the physical properties of the reservoir. But the variables which we will consider are those which are usually determined from well tests shortly after discovery and are, consequently, readily available to the engineer. They are as follows: (1) the producing separator gas-stock-tank liquid ratio, (2) stock-tank liquid gravity, and (3) reservoir temperature. Laboratory depletion studies have been performed on several reservoir fluids to illustrate the effect of changes in the cronsidered variables upon ultimate recoveries. The deviation factors, Z, of a series of reservoir fluids were determined experimentally to illustrate their order of magnitude and their effect upon the calculation of in-place reserves existing at high pressurcs and temperatures. The procedures followed in conjunction with the performance of these studies and their associated calculations are illustrated in Fig. 1. For the purpose of this paper, the depletion recoveries are expressed only in terms of pcr cent of initial stock-tank liquid, with the abandonment pressure assumed to be 500 psig. VARIATION OF RECOVERY WITH INITIAL PRODUCING SEPARATOR GAS-STOCK-TANK LIQUID RATIO The producing separator gas-stock-tank liquid ratio has long been one of the principal criteria in assumptions and generalized correlations' used for the estimation of ultimate recovery from gas-condensate reservoirs. Fig. 2 presents a plot of the cumulative recovery of stock-tank liquid at abandonment as a function of the initial producing separator gas-stock-tank liquid ratio. The graphical illustration represents the results of 44 laboratory depletion studies performed on actual gas-condensate fluids. These data are presented not only to illustrate the general trend of ultimate recovery increase with initial producing ratio increase but to emphasize the considerable variation in possible recovery at any given producing ratio. Table 1 presents the properties of two actual reservoir fluids chosen to illustrate the approximate extremities of producing ratios for gas-condensate systems. The fluids designated as A and B exhibited initial producing ratios of 3,400 and 114,000 scf/bbl, respectively. Fig. 3 presents a graphical comparison of the cumulative stock-tank liquid recoveries, calculated from the well-stream compositions and produced volumes for each fluid during depletion. It is to be noted that Fluid A exhibited a recovery of only 16.5 per cent when produced to an assumed abandonment pressure of 500 psig while the corresponding recovery for Fluid B was calculated to be 62.2 per cent. This difference in recovery, which exemplifies the general trend of recovery increase with initial producing ratio increase, is readily explained by consid-