Search Documents

By O. B. Bennett

WHEN diamond drilling was introduced in the Rhokana mines in 1939 it was used principally for pillar removal and for completion of the upper portions of shrinkage stopes which were being affected by increasing pressure. This method of drilling long blastholes proved so successful that it was extended gradually to cover stoping, pillar recovery, and hanging cave work. BY 1949 virtually all the ~roduction of Mindola and Nkana was being obtained by this method. At the present time 87,500 ft are drilled each month by the 80 diamond drills in daily operation. Responsibility for control and issue of diamond drilling equipment and crowns, as well as tabulation of all performance figures, was taken over by a sPecially formed Roto drill department, which also investigated the problems encountered with this new method. To assist this department a fully equipped test chamber, Fig. 1, was established underground where performances of various types of machines and equipment could be studied under conditions as nearly uniform as possible. Since the establishment of this department, which was eventually taken over and incorporated into the study department, considerable experimental work has been done on every aspect of the subject. The problems can be classified broadly under four headings: improvement of drilling equipment, crown design, machines, and stoping layouts. One of the major problems with drilling equipment has been to eliminate vibration. Owing to flexing of rods in the hole, severe friction is set up on the back end of the 'Ore barrel and On any high spots in the rods, inducing harmonic vibration in the string of rods and causing the crown to chatter against the face. This not only causes premature crown failure but also reduces penetration speeds and increases wear on the machines and rods used. In the early days, when only holes of EX size were drilled, vibration was largely overcome by periodic greasing of rods and core barrel during each run, but with the change-over to the larger BX hole it became obvious that application of grease by hand was inefficient and time-consuming, and attempts were made to perfect a self-lubricating core barrel. A series of these core barrels was made up and tested and a number of the latest type were used under normal operating conditions, but although footages up to 120 ft were drilled without refilling the overall performance was inconsistent, and the idea was shelved in view of the success of the stabilizer rods referred to later in this paper. At the same time tests were made with barrels 5 ft and later 6 ft long instead of the normal 2 ft. Although a slight improvement was noticed, greasing was still necessary. It was found that rod vibration increased as the core barrel became worn, and in an early test chamber experiment crowns drilled with a worn core barrel averaged 95 ft with a diamond loss of 4.76 carats, whereas the same type of crowns with a new barrel averaged 228 ft with a diamond loss of 3.13 carats. until then all BX drilling had been done with B-sized rods, but during a test on a string of BX-sized rods it was noticed that vibration was negligible. Because of the larger surface area of metal bearing on the sides of the hole, however, the friction and resistance of rods of this size rendered them impracticable on any but the most powerful of the machines, The use of stabilizers spaced evenly along the rods was the next logical step, and for this B couplings, see Fig. 2, were set with three tungsten carbide inserts 1 in. long placed around the periphery equidistantly and at an angle of 45" with a right hand lead. These were placed immediately behind the core barrel and then at 12-ft intervals, as it was found that vibration still occurred when the stabilizers were more than 15 ft apart. The effect of these stabilizers was immediately noticeable; holes were drilled with a minimum of vibration, penetration speeds were improved, and as it was no longer necessary to grease the rods there was a marked decrease in the overall drilling time for each hole. While tests were being made with the stabilizer comeb periodic were taking place with a set of tapered threaded rods, and because there was marked improvement in efficiency it was decided to incorporate the stabilizers and tapered threading in all new rods ordered for Rhokana. The feature of these rods is that only four full turns are required to tighten the coupling as against nine for the present type of B rods. Also, as they are self-centering it is virtually impossible to crossthread them. Each rod has a male 5" tapered Acme thread, Fig, 3, on one end and a female at the other, so that separate couplings are unnecessary, and every fifth rod has an

Jan 1, 1955

By David R. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are wasted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Several chemical companies in the East became concerned about supplies of pyrite early in 1943, but by late summer of that year the situation had eased. If for no other reason than national security and self-sufficiency during wartime, methods of recovering pyrite from coal-mine refuse should be worked out and made available to coal-mine operators who are potential producers of pyrite. Eastern sulphuric-acid plants are particularly likely to have their sources of raw material blocked by war conditions, so that special studies to determine where supplies of pyrite can be obtained for these plants from inland sources are desirable. Davis's1 summarization of conditions during World War I gives the following facts: During those years, the shortage of pyrite became acute. Shipments of hand-picked pyrite were made from a number of coal mines in Illinois, Indiana, western Kentucky, Ohio and Pennsylvania. A mechanical concentrating plant for sepa- rating pyrite from picking-table refuse was built at Danville, Ill., and operated for several years, and a small pyrite-concen-trating plant treating washery refuse near Gillespie, Ill., operated for several months in 1918. The Consolidation Coal Co. of Fairmont, W. Va., constructed and operated a sulphuric-acid plant using pyrite recovered from coal-mine refuse. The U. S. Bureau of Mines during 1917-1919 made a comprehensive survey of pyrite-production possibilities from coal mines and estimated that there was a potential yearly production of 435.000 tons from Ohio and Pennsylvania and 928,000 tons from Kansas, Missouri, Iowa, Illinois, and Indiana mines. This estimate included only mines that could produce one per cent or more of their coal production as pyrite containing a minimum of 40 per cent sulphur. PyRite Production According to the Minerals Yearbook,2 approximately 660,000 long tons of pyrite was produced in the United States in 1941, with an average sulphur content of 42 per cent. The average value f.o.b. mines was $3.09 per long ton. Spanish pyrite, 48 per cent sulphur minimum, was quoted at 12 cents a unit c.i.f. U. S. ports, equal to $5.76 a ton for shipments of minimum sulphur content. Most of the pyrite produced in the United States is obtained as a by-product in the dressing of copper and zinc ores. Metal mines in the East making pyrite concentrate for the market or use in company-operated sulphuric-acid plants

Jan 1, 1944

By Gifford E. White

Explanations of the basic procedure for making earth-conductivity studies by the Eltran method have already appeared in several placeS. 1,2,3 In its essentials, this method consists of applying step functions of voltage to one pair of earth grounds and measuring the transient potential resulting at a separate pair of ground points. As previously pointed out,' the transient potential resulting from a suddenly applied steady voltage is the indicia1 transfer function of Carson1 6 which has been extensively studied in network theory. The discussion here, with one special exception, will ignore the problem of how the physical configuration of the earth affects the transient response voltage; it appears that this phase of the problem has been solved in only a few special cases having any direct bearing on the prospecting problem. Entirely distinct from the potential-theory aspect of the conductivity problem is the interesting material that can be had from studying the well-known network relations between cause and effect in linear circuits, and thus deducing criteria for the application of the several experimental methods available. To do this, only one assumption need be made about the nature of the earth. The earth is to be considered a linear conductor within the tolerance of ordinary measurements. The discussion will be restricted to collinear electrode configuration like that of Fig. I, since this is the only type of spread practical for use with driving currents that vary with time. Here one pair of grounds carries the driving current, and in line with these and external to them is a RECORDING Fair of potential probes. The problem will be to consider the relation between the different voltages appearing between the potential circuit terminals when various types of driving voltage sources are inserted in the current circuit. Suppose that the grounding points G, and G2 make good contact with the earth, and that a battery of sufficient voltage to produce one ampere of direct current is introduced into the current circuit by the closing of a switch. The potential transient response to such a voltage can be measured by taking an oscillogram at the potential Directors terminals, giving the time function that has been called A(l).4 This time function has been solved for analytically in the case of a homogeneous earth,"' and the

Jan 1, 1946

By J. A. Berger, R. J. Towner

A method for determining the disorientation between sub-grains that .share a common tilt or twist boundary from measurements on X-ray micrographs is described. The method may be applied to subgrains of almost any orientation having boundary angles in the range from about 1 min to 1 deg of arc. An adaption of the Berg-Barretl method has been made to allow calculation of small angles of about 1 min to 1 deg of arc: between adjacent subgrains from the relative displacement of their images on X-ray micrographs. schulz4 gave equations for determining subgrain disorientation where the axis of subgrain rotation and the reflecting crystal planes were parallel to the specimen surface. In our method, however, they need not be parallel and, indeed, may have va:rious orientations. His camera setup, involving a fine-focus X-ray tube for obtaining high resolution with continuous radiation, was different from the one used in the present investigation (a 1.2 x 1.2 mm effective source and characteristic radiation). The X-rays produced a slight magnification in the subgrain images in the Schulz method, but not in the present method. The commonly available type of X-ray tube used permitted relatively short exposure times with a fine-grained photographic plate, which could be magnified optically many times for the examination of small subgrains. The method is illustrated by results obtained on {110} tilt boundaries in a polygonized aluminum single crystal of 99.994 pct purity. The flat crystal was stretched 6 pct in tension and then heated at 500°C for a cumulative time of 5 hr. Earlier, cahn5 studied subgrains formed by polygonization in stretched and heated aluminum crystals. He observed kink bands to have well defined boundaries lying in (110) planes, at least in the early stages of deformation. Cahn found that the (110) tilt boundaries formed by polygonization were directly related to the lattice bending about the <211> axis which lay in the (111) slip plane perpendicular to the <110> slip direction. DESCRIPTION OF THE CAMERA Our camera was similar in detail to Honey-combe&apos;s.6 Unfiltered copper radiation was used at 35 kv, and 20 ma. With the particular specimen used here to illustrate the method, a 1.2 by 1.2 mm effective source and a distance of 780 mm from target to specimen were employed, giving a convergence of 5 min of arc in the primary beam. The distance was 9.5 mm from the specimen to film. The upper 1/2- by 1-in. portion of the front surface of the specimen was irradiated with the film in parallel position. Since the specimen had been inhomogeneously deformed, many regions were in a position to reflect characteristic radiation at the Bragg Angle. Five minute exposures were satisfactory with Kodak Single Coated X-ray Film, 1 1/2 hr

Jan 1, 1961

By Paul F. Fulton, Robert K. Estes

INTRODUCTION Relative permeabilities are factual data necessary to any prediction of reservoir production behavior. One important problem in determining relative permeabilities of porous media to gas is the effect of gas slippage on these determinations. Since certain aspects of the slippage phenomenon still remain unknown, this study is particularly concerned with that problem. The validity of the theory of gas slippage as it is applied to the flow of gas through porous media has been well established. 1,2,3 Therefore, in determining the permeabilities of porous media to gas by ordinary laboratory procedure, i.e., at atmospheric pressure, the slippage correction should be considered. Rose3 performed experiments on gas relative permeabilities which indicated that the effect of gas slippage on the measured effective gas permeabilities at various liquid saturations decreased with an increase in liquid saturation. Following Rose, it was substantiated experimentally&apos; that the effective gas permeabilities at the various liquid saturations extrapolated to infinite mean pressure were the same as the non-wetting liquid permeabilities at the same saturations. This same paper also presented data which showed that the magnitude of the slippage between those values of gas effective permeability determined at atmospheric pressure and those found by extrapolation to infinite mean pressure decreased with an increase in liquid saturation. However, these experiments were not performed at liquid saturations above 30 per cent. Therefore, the purpose of this experimental work was to determine the effect of gas slippage on permeability measurements at liquid saturations in excesh of 30 per cent. APPARATUS Five core samples were used In this work: two synthetic Alundum samples (A-1, and A-2). a Nichols Buff sandstone sample (NB-13), and two samples from producing formations, a Soso sandstone (S-1), and a vugu-lar dolomitic limestone (R-7). The core samples ranged in permeability from 32 to 663 md. These cores were chosen because they represented a fairly wide range of permeabilities and probably a considerable difference in pore size and pore size distribution. Fig. 1 is a schematic diagram of the apparatus which consists of an air dehydration filter A, two Moore null-matic sub-pressure regulators B and C, the differential oil manometer D, the core holder E, the flowmeter F, the soap reservoir G, and a mercury manometer H measuring the downstream pressure. The interesting features of the apparatus are the two Moore vacuum-pressure regulators. The regulators permit the rapid establishment and easy control during flow at sub-atmospheric pressures of both the differential and downstream pressures, and prevent the surging action of the vacuum pump from disturbing the system during flow. Provided there are no leaks in the system, these regulators will maintain without measurable change selected downstream and differential pressure. Specifically, regulator B controls the downstream pressure and regulator C controls the differential pressure. In opera-

Jan 1, 1957

By E. A. Kilinski

THE mineral production of Dutch Guiana has been of little consequence. This is due to several rea-sons. Inaccessibility is probably the greatest factor, for the Guianas are off the main commercial route. More or less closely related causes are the tropi-cal climate and the temperament of the inhabitants. Small quantities of gold have come from Dutch Guiana for many years, and recently bauxite has entered the list of exports. It is likely that other minerals may be found in commercial quantities. The Colony is on the northeast coast of South Amer-ica. It is known by two names, that of Dutch Guiana, and that of Surinam. - British Guiana (Demerara) adjoins it on the west, French Guiana (Cayenne) on the east, and Brazil on the south. It covers an area of approximately 58,000 sq. miles. The population, in the. neighborhood of a hundred thousand,, is small, but the variety of races and the sub-sequent mixtures of these is almost incredible. This unusual and colorful population readily falls into three groups, (1) those of the bush, (2) those of the planta-tion, and (3) those of the towns. The bush people con-sist of two groups, the Indians and the bush-negro. The Indians, of whom there are but a little over two thousand, keep entirely to themselves, lead a. very primi-tive existence, and rarely come into the towns. The bush-negro gives the touch of human life to the thick jungles. A descendant of escaped slaves of by-gone days, he is at present a proud, stalwart, happy, clean, moral, carefree and ease-loving individual-a distinct personality. Work is not his pal, although he does cheerfully that which is necessary for his existence. He will transport passengers and goods in his dugout and guide the stranger through the jungles, but that is all. The plantations employ some negroes, but more Javanese, imported as contract labor from the East Indies. Paramaribo, the only large town in Dutch Guiana, is the center of all government, commercial, and social activities. It has a motley population of 40,000, in-cluding negroes native to Dutch Guiana and many from all parts of the West Indies. In addition, there are Javanese, Chinese, and some Hindus. The two latter groups control most of the retail trade. The Dutch and a few scattered Germans are the only Europeans. All of the higher government offices are held by the Dutch, the others are filled from the ranks of the natives. Marriages and intermarriages among these various groups have produced types that defy almost any effort to decipher an individual&apos;s forbears. Dutch is the official language, but among the people a jargon known as Tahki-Tahki holds sway. English is taught in the schools, consequently many speak it, and many more can make themselves understood in that language.

Jan 2, 1928

By Edward Keller

Under the title, Labor-Saving Appliances in the Works-Laboratory, I published a paper1 in which mas described how multi-manipulations in a works-laboratory and in the furnace-room of an assay-laboratory, can be condensed into single manipulations by applying the proper mechanical devices. For example, I now deposit ill, or withdraw from, a muffle a set of 48 cupels as one unit. The front row (8) of these are blanks or heaters; the other 40, when they have attained the proper temperature in the muffle, are charged simultaneously with the 40 lead-buttons. Three manipulations here accomplish an operation which by the generally customary method requires 136, and this number is only limited by the size of muffle and cnpels. This operation is an enlargement of what I have already described in my former paper, and Fig. 1 shows the improved implements. In the paper referred to I described a gold-silver bead parting-bath, which is the last of the devices used in regular sequence in practice. This bath mas designated as being convenient, but mas not a labor-saver properly. Fig. 2 of the present paper shows a new device. Instead of the original tray, there are now sectional holders for the test-tubes, each having a wooden handle on either end, so that the holders ma?-be removed from the boiling bath, and the acid or water poured oE from each set of tubes (in this case, 7) without waiting to cool. The tubes, held in place by clutches, as shown in Pig. 3, rest in holes in the base-strip, having a smaller diameter than the tubes. Each holder is stamped at either end with a number, so that the bath becomes further useful by permitting several men to use it at the same time without interference. Apart from the handles, the holders are made of sheet-copper.

Jan 1, 1911

By A. A. Gustafson

IN diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport&apos;s operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1040. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Freeport Sulphur Co. discharges over the entire circumference, which gives a discharge lip of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole. The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By Albert E. Ketler

Introduction – The introduction of computerized monitoring and control (M/c) equipment into the U.S. coal mining industry may prove to be of truly revolutionary proportions in the 801s.Many of you are aware that the British have developed and have been using such sophisticated M/C equipment for performing production and safety related tasks in their coal mines for nearly a decade. The benefits of M/C systems in the mining industry are usually separated into those which improve productivity, and hence make money for the company, and those which improve safety, and hence cost money. The economic benefits of M/C are startling for the production related functions such as for monitoring and controlling conveyor belts, de-watering pumps, electrical power distribution, and the like. It doesn&apos;t take much analysis to show that hundreds and even thousands of tons of coal don&apos;t get mined every time a belt shuts down or when power is out due to circuit breakers tripping for any number of reasons. A flood, caused by a malfunctioning pump which goes undetected for lack of feedback monitoring of pumping parameters, can destroy literally millions of dollars worth of mining equipment. The M/C system would be justified or not based on whether or not the productivity benefits balanced the cost within a timespan commensurate with the return on capital philosophy of the company. The safety related benefits are easily underestimated or ignored completely and the purpose of this paper is to under-score some of these benefits, as well as to review the application of M/C to the coal mining industry. The companies involved are Transmitton Ltd of England and Minetics Corp of Pittsburgh, Pennsylvania. Transmitton is probably the most experienced manufacturer of M/C equipment in the world having some 200 installations to its credit. Minetics is the marketing and manufacturing arm for Transmitton in the U.S.A. and is responsible for all aspects of distribution and service. Plans are underway for manufacturing of the Transmitton hardware for U.S. sales to be transplanted into U.S. subcontractors by 1981. Thus our coal mining industry will benefit from British technology, but without the delays and additional costs usually involved in international shipments.

Jan 1, 1981

By H. R. Stahl

THE disseminated lead district of Southeast Missouri lies 70 miles south of St. Louis. The only metal of economic importance in the ore is lead, but minor amounts occur of iron, zinc, copper, cobalt, nickel, silver and cadmium. These minor metals, as might be expected, tend to concentrate in both the flotation and table middlings. In the past, some zinc has been recovered by differential flotation. The silver and cadmium tend to associate with the zinc, and some recovery is made of these two metals at the smelter. The lead occurs as galena, or lead sulphide. The minor metals are also present as sulphides. The presence of oxidized lead is suspected, but has not been definitely proved. The gangue is chiefly dolomitic limestone, with small amounts of sandstone and shaly glauconitic and chloritic minerals. The ore contains about 3.25 per cent lead, occurring as galena disseminated through the gangue. Some of the galena is very finely disseminated, and the mineral in the gravity tailings, or chat, is seldom or never in the free state. The method of treatment of the ore has been evolved over a period of 75 years; hence probably is not far from correct. The milling processes have tended toward simplification during the past 15 years, but recoveries have never been sacrificed for the sake of simplicity. In many cases, simplification of flowsheets has led to better recoveries and operating economies. A simplified flowsheet is shown in Fig. I. The St. Joseph Lead Co. operates four mills in the Flat River district, with a normal total capacity of about 21,000 tons per day, divided as follows: Federal mill, 11,000 tons; Leadwood mill, 4500 tons; Desloge mill, 3400 tons and Bonne Terre mill 2400 tons. The methods of concentration used at these plants are similar in principle; they differ mainly in details and in the type and size of the equipment used. The process of concentration may be divided into five main steps; i.e., dry crushing, wet grinding, classification with its attendant desliming, tabling and flotation. A brief description of these processes will be given, noting important differences in the various plants, and also noting the more important changes or developments of the past few years. DRY CRUSHING The run-of-mine ore is hoisted in skips, the capacity of these skips ranging from 2 ¾ tons to 8 ¼ tons. At the Desloge plant, the ore is hoisted in 2-ton mine cars on self-dumping cages. All ore is hoisted at shafts adjacent to the various crushing plants, no ore being transported on the surface. Primary breaking at all the mills is accomplished with 9E Telsmith breakers. Preliminary screening is provided ahead of most of these crushers, either by station-

Jan 1, 1943

By David R. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are wasted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Several chemical companies in the East became concerned about supplies of pyrite early in 1943, but by late summer of that year the situation had eased. If for no other reason than national security and self-sufficiency during wartime, methods of recovering pyrite from coal-mine refuse should be worked out and made available to coal-mine operators who are potential producers of pyrite. Eastern sulphuric-acid plants are particularly likely to have their sources of raw material blocked by war conditions, so that special studies to determine where supplies of pyrite can be obtained for these plants from inland sources are desirable. Davis&apos;s1 summarization of conditions during World War I gives the following facts: During those years, the shortage of pyrite became acute. Shipments of hand-picked pyrite were made from a number of coal mines in Illinois, Indiana, western Kentucky, Ohio and Pennsylvania. A mechanical concentrating plant for sepa- rating pyrite from picking-table refuse was built at Danville, Ill., and operated for several years, and a small pyrite-concen-trating plant treating washery refuse near Gillespie, Ill., operated for several months in 1918. The Consolidation Coal Co. of Fairmont, W. Va., constructed and operated a sulphuric-acid plant using pyrite recovered from coal-mine refuse. The U. S. Bureau of Mines during 1917-1919 made a comprehensive survey of pyrite-production possibilities from coal mines and estimated that there was a potential yearly production of 435.000 tons from Ohio and Pennsylvania and 928,000 tons from Kansas, Missouri, Iowa, Illinois, and Indiana mines. This estimate included only mines that could produce one per cent or more of their coal production as pyrite containing a minimum of 40 per cent sulphur. PyRite Production According to the Minerals Yearbook,2 approximately 660,000 long tons of pyrite was produced in the United States in 1941, with an average sulphur content of 42 per cent. The average value f.o.b. mines was $3.09 per long ton. Spanish pyrite, 48 per cent sulphur minimum, was quoted at 12 cents a unit c.i.f. U. S. ports, equal to $5.76 a ton for shipments of minimum sulphur content. Most of the pyrite produced in the United States is obtained as a by-product in the dressing of copper and zinc ores. Metal mines in the East making pyrite concentrate for the market or use in company-operated sulphuric-acid plants

Jan 1, 1944

By Jim Douglas, H. H. Rachford, D. W. Peaceman

The problem of unsteady-state gas flow through porous media has been solved numerically only for the case of linear or radially symmetric reservoirs. A recently introduced numerical method for solving the unsteady-state heat flow equation in two dimensions is applied to the calculation of the depletion of a square region containing a perfect gas. Solutions are presented in graphical form for various values of dimensionless parameters. The solutions are compared with published .solutions for radial reservoirs. I NTR ODUCTION The problem of unsteady-state flow of gas through porous media gives rise to a second-order non-linear partial differential equation for which no analytical solution has been found. Numerical approximations to solutions of the gas flow problem have been obtained by the stepwise solution of an associated difference equation1,2. However, the methods so far developed have required that the reservoir be either linear or radially symmetric. This restriction in shape has been necessary so that only two independent variables be considered, namely, one distance variable and time. In order to deal with reservoirs having more realistic shapes, it is necessary to develop numerical procedures for the solution of the gas flow problem involving two distance variables. A numerical procedure, denoted as the alternating-direction implicit method, for the solution of the heat-flow problem in two dimensions has recently been introduced" By the use of this procedure, approximate solutions have been obtained for heat-flow problems in a square8, and in regions having various non-rectangular boundariesa. Because of the similarity between the equation for heat conduction in solids and the equation for gas flow in porous media, it is reasonable to expect that the alternating-direction implicit method should also be useful for solving the gas flow problem in various two-dimensional regions. Solutions have been calculated for the simplest two-dimensional region, a square reservoir with a single well in the center. While reservoirs of such simple geometry seldom, if ever, exist, the solution of this problem is of some practical importance because it is also the solution of another problem, that of determining the depletion history about an individual well in an infinite uniform reservoir containing wells spaced throughout on a square lattice and producing equally from each well. Finally, it is of interest to compare solutions for a square reservoir with those for a circular reservoir and to determine the effect of the shape of the boundary for that particular case. METHOD OF CALCULATION Basic Differential Equation By combining the equation of continuity, the perfect gas law,

Jan 1, 1956

"The richest hill on earth" had its start as a placer gold camp in 1864. The gold was quickly worked out but then silver was discovered in the copper ores in Butte Hill. After ten years as a silver camp, rich copper ore was found in 1881 and the future of Butte was assured. In the early 1960&apos;s, the Anaconda Company began the shift from underground mining at Butte to open pit mining of the enormous, low-grade copper deposit surrounding the old high-grade veins which had been worked for over eighty years. Their first primary crusher was a 66 in. by 84 in. (168 m by 2. 13 m) jaw crusher. The pit was expanded at such a rate, however, that its location became endangered. Additionally, the new Clyde Weed concentrator had been built at Butte; and in 1969 construction of a new gyratory installation was started. The primary crusher at the Clyde Weed concentrator is one of the most unusual primary crushers ever put into operation. At times, the ore from the Berkeley pit contains large amounts of timber, pipe, rails, and so forth left in the ore body from the old underground mining operations; and the crusher installation had to be designed so this tramp material could be readily removed ahead of the crusher. Ore is delivered by 100- and 150-ton trucks to two side-by-side dump pockets, each with a capacity of 400 tons. Originally, a hydraulic grapple was installed on the dividing wall between the dump pockets; but it was found that oversize boulders large enough to block the discharge opening at the bottom of each hopper were rapidly covered with other material, and the grapple was unable to reach and remove the large boulders causing the blockage. In addition, the grapple was located in a quite vulnerable position; and it sustained damage from being struck by rock dumped from the trucks. Oversize boulders are now blasted. Underneath each pocket is a vibrating grizzly feeder with the grizzly bars set at 4 in. (102 mm). These feeder-grizzlies are 84 in. (2. 13 m) wide and 32 .ft (9. 75 m) long, with grizzly sections 16 ft (4. 88 m) long. Approximately 75% of the ore passes through the grizzlies and grizzly oversize then drops onto two parallel 6 ft (1. 83 m) wide picking belts. The belts are 3 in. (76 mm) thick and rest on idlers supported by air- filled rubber shock absorbers. At the side of each picking belt is a hydraulic grapple which is used to remove timbers too large to be removed by hand. At times, four men are used to remove timber and tramp iron. Timbers are dropped onto a transverse belt conveyor which discharges into a truck stationed outside the primary crusher building,

Jan 1, 1978

By C. E. Stafford

and tougher, and will carry double the tonnage of any of Dr. Dud ley&apos;s soft mils. C. E. Stafford, Steelton, Pa.: I must confess my high ap preciation of Dr. Dadlq&apos;s conscientious and painstaking work, and of his scientific methds in obtaining the data; but with his method of handling these results and with his conclusions drawn therefrom 1 canuot agree. The reasons for this difference of opinion I will endeavor to explain. It is apparent on inspecting his Plates 6 and 7 that the majority of the slower-wearing rails are from the north track, and generally have a longer time of service, a greater average tonnage per rail, and a smaller avernge tonnage per year per rail than the faster wearing, the majority of which are from the south track, and gener ally have a shorter time of service, a smaller average tonnage per rail, and a greater average tonnage per year per rail. Have these facts any significance Have these different of conditions to which they are subjected any baring on the relative wearing capacity of these rails I venture to say they have. I think, after a study of Table I (page 676), (an arrangement of linee 17 and 18 of Plate a), in connection with Plates 6 and 7, we will find that the slower wear of the 32 best rails is only partly due to qualities inherent in the rails themselves, but is principally due to external conditions favorable to slower wear. In regard to the north and south track, we know that over the rsoiith track come the loaded cam from the West, and that over the north track these cars return, most of them, empty. It is evident that this means for the north track a less average tonirage per rail per year; or, in other words, a lower wheel tonnage. When the load per wheel is less, the resistance and consequently the wear must, necessarily, be less, other things being equal. Time of service, alee, has an important bearing on the question in hand. It has been only within the last five or six years, as Dr. Dudley has pointed out, that the roadbed of the Pennsylvania Rail road has reached its present admirable condition. Before this time the njadbrd was more elastic, more yielding (and probably not uni tbrmly so) than at present. These circumstalices might cause a sofier rail to be more durable than a harder one, owing to the fact that it ulonId yield rnore or less to the bending force of the passing load and would thus get a bearing on each cross-tie. The harder rail, on the other hatid, being stiffer and more. unyielding, would not

Jan 1, 1881

By Galen Clevenger

THE losses of gold and silver occurring during the conversion of the precipitate, resulting from the cyanide process, into bullion may occur in two ways: first, there may be mechanical losses during the handling of the precipitate up to the time that it is charged into the melting furnace; and second, there may be losses after the precipitate reaches the melting furnace. Much of the loss during the handling of the pre-cipitate can be eliminated, and in fact, in modern plants this loss is known to be very small; particularly since preliminary acid treatment of the precipitate with the attendant extra operations has been abandoned in all but certain plants where gold predominates and this extra step is still deemed necessary. The losses in the melting furnace are from dusting and volatilization; losses in the furnace bottom and linings; floor sweepings; and slag and matte. The gold and silver in the: products which do not: go out of the flue are readily recoverable by standard methods, and while there may be considerable gold and silver tied up at times, the ultimate loss with careful "work should be small. The losses resulting from volatilization and dusting in connection with the melting of the silver slime from copper refineries have been determined by standard methods, and the possible recovery: definitely estab-lished through the installation and operation of electro-static precipitation units. This subject has not been thoroughly investigated in connection with the melting of`. cyanide precipitate; at least, there are no published accounts of such tests. Experiments have been made in the past to determine melting losses by weighing and assaying the precipitate, but this method gives results which are uncertain on account of the difficulty of accurately sampling and assaying cyanide precipitate. Attempts to ascertain these losses by bubbling a measured sample of the gas through cyanide solution or, other absorbent have likewise failed to give depend-able results.

Jan 1, 1922

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930&apos;s. During these meetings the many advantages to be gained through the use of dust- collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine&apos;s own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine&apos;s power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market out- lets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer&apos;s knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk so-ton lots direct to the consumer. POTENTIAL MARKETS FOR FINE- MESH COAL DUST In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, “sea coal” distributing plants, water-purification plants and obviously, pow-

Jan 1, 1944

By J. H. Wernick

IN temperature-gradient zone-melting1 a molten zone is moved through a solid or across a solid surface by the establishment of a temperature gradient. This technique has both practical and fundamental aspects. One practical application is to make p-n junctions for semiconductive devices, particularly for devices in which the junctions are desired within the semiconductor. From a fundamental point of view, the technique is being investigated as a method for determining diffusivities in liquid alloys, and preliminary diffusivity results have been reported by the writer." In this paper, the effects of crystal orientation, temperature, and molten zone thickness in temperature-gradient zone-melting, and the bearing of these effects on diffusivity measurements and n-p-n junction formation are discussed. Experimental Procedure An effect of crystal orientation was noted in early experiments. To facilitate its study, movements of wire zones across a surface, rather than through the body of a single crystal, were observed for various surface planes and travel directions. The experirr-entai setup is illustrated in Fig. 1. The graphite end-section for the high temperature heater has an apron about 1/16 in. above the upper surface of the crystal. This apron insures that the surface temperature of the block is equal to or greater than the temperature within the block at every point, Thus, the zone does not penetrate the block and convection in the liquid is minimized. The experi-through a block is shown in Fig. 2,

Jan 1, 1958

By J. W. Stewart

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I). It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the 15 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remain¬ing to schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941

By F. Kurata, P. C. Davis, T. L. Gore

An experimental method and apparatus for the study of the low-temperature phase and volumetric behavior of volatile mixtures are described. The phase diagrams, including the critical points, and the volumetric behavior of a natural gas and a mixture of the natural gas with methane at temperatures from -40°F to -200°F and pressures to 1.200 11si are givrn. INTRODUCTION Knowledge of the phase and volumetric behavior of mixtures of the light hydrocarbons at low temperatures is becoming increasingly important as interest in low-temperature separation processes increases. Distillation at low-lemperatures has been used for some time to recover ethane and ethylene from natural gas and refinery gas for petrochemical uses. Removal of excess nitrogen from natural gas by distillation has been proposed as a means of increasing the capacity of gas transmission lines and of improving the marketability of the gas.1,2 Evaluation of the latter process has been hampered, however, by the scarcity of data from which the phase behavior of natural gases at low temperatures might be predicted. While existing correlations of vaporization equilibrium constants may be used to predict the behavior of such mixtures at lower pressures, high-pressure computations often require knowledge of the location of the critical point of the system involved. Although correlations have been developed for the prediction of the critical temperature and pressure of certain types of hydrocar-bon systems, they do not apply to very volatile systems such as nitrogen-bear-ing natural gases. This paper describes the initial stages of an investigation of the low-temperature behavior of a numher of natural gases and other gases of commercial interest. The experimental method and apparatus are described. and the phase and volumetric behavior of a natural gas and a mixture of the natural gas with methane are presented. PREVIOUS WORK The published low-temperature vapor-liquid equilibrium data for hydrocarbons and mixtures of hydrocarbons with nitrogen and helium are listed in Table I. Most of these data are for binary systems, and the data of Stutz-man and Brown" at 100 psi are the only data on a natural gas. The data of Bloomer and Parent3 on the methafie-nitrogen system, which have been phblished since this study was completed, are a valuable addition to the knowledge in this field. Prior to the publication of these data the only published critical point data on systems having critical temperatures below the ice point were those of Ruhemann.1 on the methane-

Jan 1, 1952

T. A. Rickard, Denver, Colorado: The observations made by the author concerning the treatment of gold-bearing ores, deal with the subject only briefly and in a general way; but, coming from an authority, they invite comment. In stating the fact that a " finely-divided condition " is a necessary characteristic of ores containing free gold, the author must be refer ring to those mining districts only with which he himself is ac quainted. The statement would not be true of certain gold-mining regions in America and Australia. The ores of some Californian mines and the mill-stuff treated at certain of the mills of Clunes and Ballarat in Australia, and of Otago in New Zealand, contain the gold in a free but in a coarse state. Moreover, "reduction to fine sand and flour" is not required by certain ores, even though the gold be in a finely-divided condition. In such cases the gold becomes de tached from the quartz before the gangue has been pulverized into particles as small as those in which the gold occurs. The dry-crushing of free-milling gold-ores is onknown in the new mining regions of the world. It is not clear whether the author has in mind any European district in which such a process is in actual use. If he has, a description of the method and the results obtained would be very valuable. Dry-crushing is, other things being equal, twice as slow and twice as expensive as wet-crushing. In the case of free-milling gold-quartz it serves no purpose, since such ore does not carry sulphides which contain any large percentage of value, and which, by being slimed, may carry away part of that value. The dry-crushing of a free-milling gold-quartz would be considered an absurdity by an American metallurgist. If the ore contain "free gold only," why submit it to a further treatment, such as concentration, after its passage over the amalga mating-plate ? What does the author propose to concentrate ? Again, why anticipate the treatment of tailings by the McArthur Forrest, or some other process ? The satisfaction felt by a mill-man in saving gold by a subsequent treatment of the tailings from his mill appears to me to be like that of the man who shoots at a rabbit,

Jan 1, 1894