Search Documents

By James Bowron

Considering the importance of the steel trade and the strategic position occupied in it by the Birmingham district, it may be surprising to many to learn that the first pig iron smelted with coke was made in Alabama on Feb. 28, 1876, although merchant pig iron had been produced in Rockwood, Tenn., in 1867 -a plant that is still in operation The heavy deposit of Clinton ore, extending from Pennsylvania into Alabama, varies greatly in accessibility, on account of geological changes such as erosion or anticlinal upthrow; it varies equally as much in thickness and in quality. The brown ores extensively scattered through the South also vary materially in quality—some are relatively low in phosphorus and high in manganese, and vice versa. The red ore varies materially in phosphorus, but the iron produced from this ore was always considered too high in phosphorus for treatment by the acid bessemer or open-hearth process and did not contain sufficient phosphorus for the basic bessemer process. Under these conditions there remained only the basic open hearth as a possible process; and for many years it appeared impossible to use this, because, with coke smelted iron, the silicon was too high to permit its use in basic lined furnaces. Various attempts were made, from time to time, to produce a low-silicon iron, by carrying high lime burdens together with harder blowing, but the blast furnaces of the South were not equipped with the blowing power of today and from 31/2to 5-lb. pressure was the normal working condition. The result of these experiments, therefore, was that a furnace would get a lime set or be hastily changed to avoid scaffolding, and engineers and superintendents were careful not to renew the experiments. After the development of the beds of dolomitic stone in East Birmingham, the carrying of sufficient lime to bring down the silicon in the blast furnace to the permissible open-hearth limit was successfully done at the Alice furnace in Birmingham, commencing July 22, 1895. In a very short time the entire output of that furnace was being sold to different Northern steel manufacturers, with a guarantee that silicon and phosphorus should run below 1 per cent.

Jan 1, 1925

The most extensive oil shale development program ever undertaken in the United States has been that carried out by Colony Development Operation at Para- chute Creek in western Colorado. Field development goals were completed this spring, with the remainder of the $24 million joint venture program, primarily engineering, environmental and economic analysis, due to be finished by the end of 1972. Upon completion of the overall program, a decision concerning a commercial venture is expected. This program points up the increasing attention being focused on oil shale as a source of crude oil and energy for the U.S. at a time when the nation's supply of oil produced by conventional methods is far from adequate to meet the demand. The oil shale reserves of the Green River formation in Colorado, Utah and Wyoming are the largest hydrocarbon reservoir. The Piceance basin of Colorado, alone, contains some 80 billion bbl of shale oil recoverable by modern methods in reserves more than 30 ft thick and containing at least 30 gal of oil per ton. The U.S. Geological Survey has estimated that the total shale oil reserves of the Green River formation in the states of Colorado, Utah and Wyoming is more than 600 billion bbl of oil in deposits containing at least 25 gal per ton of shale oil.

Jan 10, 1972

By Leonard E. Wood, Yeghishe M. Avedissian

Knowledge of the basic properties of rocks-strength, structure, and permeability-is prerequisite for the success of foundation work for masonry dams, large bridge piers, and tunneling as well as for excavation in rock and special underground construction. Strength of engineering materials depends upon texture and structure as well as the environmental conditions to which they have been subjected. Failure in its widest sense implies the transition of a material from elastic to plastic state (yield strength), from continuous to discontinuous state (rupture strength). The compressive strength of a material such as rock is the stress at which a sample, loaded and unconfined at the sides, fails by rupture. Some of the external factors that control strength of rocks are the nature and type of stress, whether uniaxial or triaxial, compression, tension, or torsion. Another important factor is the rate of stressing-whether constant, impact, or gradually increasing. Of the internal factors, the effect of texture upon strength is obvious. Generally, fine-grained rocks have higher compressive strength than coarse-grained prototypes. Among metamorphic and igneous rocks those with better and higher degree of interlocking of their crystals are generally stronger than the ones with poor or lower degree of interlocking. In sedimentary rocks, the degree and type of cementation has a great influence upon their strength. Structurally, the existence of fissures, cracks, and seams of argillaceous or organic materials in a rock specimen will greatly reduce its strength. Because most rocks are characterized by bedding planes, laminations, or foliations, they are anisotropic in their physical properties and hence compressive strength depends on the orientation of the bedding planes to

Jan 1, 1972

By W. D. Smith

It has been 5 years since the writer left the Philippine Islands and while in that country his chief work did not lie in this field, though he has visited all but one of the localities mentioned in this article. The principal field studies relating to oil were M de by his colleague, Mr. Wallace E. Pratt. The writer's investigations ealt with the general stratigraphy and paleontology of the Philippines. with the exception of the investigations made by Mr. Pratt and the writer very little information on this subject is available. A number of geologists in the employ of large oil companies have visited the Islands from time to time but, following the general rule, the public has scarcely ever been permitted to learn anything of the results. The writer is indebted to the Bureau of Insular Affairs, Washington, for late information regarding recent legislation in the Islands relating to petroleum. All the known oil seeps, petroleum residues, such as ozocerite, and natural-gas emanations are associated with Tertiary sediments. The chief seeps and most promising prospects are located as follows: 1. Bondoc Peninsula (lower end), Tayabas Province, Southeast Luzon. 2. The west coast of the island of Cebü from Alegria north to, and perhaps beyond, Toledo. 3. Central Mindanao not far from Lake Lanao. 4. The ozocerite veins on the Island of Leyte in the northwestern part in the vicinity of the town of Villaba. 5. Natural gas from some deep wells in Tertiary shale formations on the eastern flank of the Cordillera and extending out under the plain on the island of Panay. The first mention in geological literature, to the writer's knowledge, of gas or petroleum in the Philippines is found in the description of the Island of Panay by the Spanish geologist, Abella, in the year 1890. In 1898, an oil well was being dug on the estate of Smith Bell & Co., an English concern, near the town of Toledo on the west coast of Cebu. In

Jan 1, 1921

By George W. Maynard

For an account of the discovery and the determination of chromite on Port au Port Bay I am indebted to Mr. Obalski, Government mining engineer for the Province of Quebec. He writes: " In June, 1894, with the authorization of our Government, I went to Newfoundland to examine some asbestos property. Passing through Halifax, I had interviews with some gentlemen who told me that besides the asbestos there was in the same district a big deposit of iron-ore. They handed me some specimens, and, after ascertaining that they were not magnetic, and learning that they were found in serpentine, I said they were chromic iron. I visited the place on June 27, 1894, and confirmed my opinion, pointing out at the same time the importance of the deposit, as appears in my report of July 9, 1894. I do not claim any credit for the discovery of chrome-ore in Newfoundland; but, as a matter of fact. when I came in contact with the Halifax gentlemen they did not appear to know the nature or the value of the mineral until I mentioned to them that it was chromite. "' Mr. Obalski's report was mainly devoted to the asbestos-deposits. That portion relating to the chromite was as follows: " On the right side of the creek there is a show of chromic iron of good quality, which appears scattered through the serpentine in several places on the face of the cliff for 40 to 50 feet. A few boulders are found farther up at a distance of 100 feet, and also in the ckeek itself. From this point the deposit exists on a relatively large area, the widest exposures being from 6 to 7 feet. Chromic iron deposits in serpentine rock have no regularity, and are merely pockets. In the case of the property in question this rule is not changed, but the pockets look to be of large extent, and could be easily worked." My own preliminary investigation of the property was made

Jan 1, 1898

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory investigatorsstate of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which andare useful for predicting machine performance and give acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary canexplain commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted.'TheRittinger In its first form, as stated by P. R. Ritted.'tinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include the concept of surface energy; in this form it was precisely stated by A. M. Gaudin' as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended." According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported- hat support the theory in its first form by indicating that the new surface produced in different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work done on the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading, since it does not follow the regular breakage pattern of most materials but is regularrelativelybreakage harder to grind patternat the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory4 is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr /log 2." The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-l.V f a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The evaluation in terms of kw-hr per net ton of —200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of —200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1953

By J. C. Todd

The volume of air needed to move the combustion wave through each acre-foot of the reservoir is a very important quantity for engineering economic analyses. A new method, which involves backflowing the injection well, has been developed for determining the air requirement .for the forward combustion thermal pilot in the Delaware-Childers field. The method depends on measurement of the total volume of air injected and measurement of the pore volume in the zone swept out by the combustion front. The basic premise of the method is that the pore volume of the swept zone contains air, while the formation around this zone contains flue gas, oil and water. The pore volume of the swept zone is determined by blowing down the pilot section of the formation through the injection well after the pilot is shut down. Oxygen balance is used to differentiate between air from the swept zone and flue gas from the surrounding formation. Data indicate that air'is produced from the swept zone by relatively efficient miscible displacement by the flue gas. The pore volume occupied by the air in the swept zone is determined by simple PVT relationships. The average temperature of the swept zone is calculated by heat balance from the total amount of heat generated during the pilot and losses to the surrounding formation. The new method was applied successfully at the conclusion of the pilot in the Delaware-Childers field; the air required for the reservoir conditions involved was calculated to be 19.2 MMscf/acre-ft of reservoir swept. INTRODUCTION One of the most important pieces of information to be found from a forward combustion pilot is the air requirement; that is, the volume of air needed to move the combustion wave through each acre-foot of the reservoir. Compression costs per barrel of oil recovered, which are a direct function of the air requirement, are a large portion of the expenses incurred in the thermal recovery process. Thus, the profitability of thermal recovery depends largely on the air requirement, which is a measure of the amount of fuel deposited and burned in the thermal recovery process. Several attempts have been made to correlate crude oil properties with fuel deposition and, hence, air requirement.l*2 Other attempts have been made by our laboratory to find the air requirement by material balance, gravity survey, pressure transient analysis,3 magnetic survey and the poten-tiometric model. Better methods are needed to predict more accurately the economics of fieldwide application of the process. Another method of finding the air requirement consists of operating a pilot thermal project for several years. This is followed by an extensive coring program to define the volume swept by the combustion wave. The air requirement is found from the total injected air divided by the volume of the swept region found from the coring operation. This method is costly; an adequate coring program usually costs several hundred thousand dollars. A thermal pilot was operated in a watered-out portion of the Delaware-Childers field, Bartlesville sand, from Nov., 1960, until May 3, 1965. One of the primary purposes of this pilot operation was to determine the air requirement for economic calculations which determine the advisability of expanding the project to the entire 128,000 acre-ft field. Barnes4 has described the result of this pilot operation,, including calculation of the air requirement from limited coring data. The value obtained, as calculated, was 15.8 MMscf/acre-ft. One purpose of this report is to describe a new method of finding the air requirement from a thermal pilot operation. A second purpose is to describe the application of this method to the Delaware-Childers thermal pilot. THEORY AND DESCRIPTION OF THE METHOD The combustion zone in the forward combustion process is propagated from injection w producing

Jan 1, 1970

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory investigatorsstate of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which andare useful for predicting machine performance and give acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary canexplain commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted.'TheRittinger In its first form, as stated by P. R. Ritted.'tinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include the concept of surface energy; in this form it was precisely stated by A. M. Gaudin' as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended." According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported- hat support the theory in its first form by indicating that the new surface produced in different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work done on the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading, since it does not follow the regular breakage pattern of most materials but is regularrelativelybreakage harder to grind patternat the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory4 is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr /log 2." The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-l.V f a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The evaluation in terms of kw-hr per net ton of —200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of —200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1953

By P. R. Sheorey

Understanding of in situ rock mass behaviour has taken a step forward with the advent of the refined rock mass classifications of Wickham, Bieniawski and Barton et al. In this paper six case studies are given in brief showing how Barton's classification could be used in mining situations. The cases cover stability of roadway junctions under shallow covers, support pressure estimation in roadways in intact and failed rock conditions, determination of the safe unsupported span of a wide stope and estimating the stability of roadways in two contiguous seams standing 011 small pillars against puncture of the parting rock.

Jan 1, 1983

Jan 1, 1951

The 118th meeting of the Institute was under the auspices of the Institute of Metals Division and the Iron and Steel Section, and was held at Milwaukee, Wis. The opening session was a joint meeting with the American Foundrymen's Association and the American Malleable Castings Association, and was presided over by Benjamin D. Fuller, President of the American Foundrymen's Association. At this time Hon. Emanuel

Jan 12, 1918

By Alden Greninger

MANY recent contributions in the field of theoretical metallography have been concerned with crystallographic definitions or descriptions of various phenomena. The lattice orientation of the crystal being studied must be known before such definitions can be made. Practically all the metallic crystals used do not have crystal faces-other than the unknown "plane of polish"; hence resort must be had to other means of determin-ing orientations. Some use has been made of etch-figures, slip bands, optical properties, etc., for this purpose; but for. accurate results, and because of the fewer restrictions to their use, the various X-ray methods have been the most satisfactory.1 The methods that, have been used may be divided into two general classes: (1) oscillation methods, and (2) transmission Laue methods-2

Jan 1, 1934

By J. D. Miller, R. L. Atwood

The structure, properties, and composition of commercial chelating-type copper extractants are examined. Characterization of these extractants was accomplished using organic separation techniques and analytical tools such as NMR and infrared spectroscopy. Results indicate that only the trans isomer of the diphenylhydroxyoxime (LIX 64N) is capable of copper chelation. The effects of structural modification of the extractants on the extraction and stripping reactions are discussed.

Jan 1, 1974

By Olev Trass

The mill body is a stationary grinding cylinder inside which a number of helically grooved rollers rotate, each being suspended on a flexible axis. The feed material is repeatedly crushed between these rotors and the cylinder, with the crushing force created by radial acceleration. The mill has several internal design variables such as number, size and shape of rotors, and can be operated wet or dry. It is compact, has a high capacity, modest power consumption, and can grind many materials down to ultrafine powder. Illustrative data on product size distributions and particle shapes are given for grains, metals and minerals obtained at various operating conditions, along with initial results on grinding kinetics.

Jan 1, 1980

By Dan Chun

Abstract-To facilitate the efficient handling of large volumes of information generated by logging exploration drill cores, a computer data bank system (GEOBANK) has been developed to store and retrieve the normally difficult to handle geologic information as well as the physical testing data. The data bank systematized the logging of drill core by first developing a standard list of adjectives or descriptors (with the corresponding assigned numerical codes) for the various stratigraphic categories that are also assigned numerical codes. The system uses the "floating-slot" concept and handles the data bank with one single input form.

Jan 9, 1978

By D. W. Kestner

Recent developments and trends in the state of the art as being commercially applied to the pelletizing and sintering of metallic ores, concentrates and reverts will be reviewed. Both ferrous and non-ferrous materials will be covered. The influence of environmental considerations on the decision to build, the process selection, and design of the plants will be discussed. Use of coal in iron ore pellet induration will also be reviewed as the availability and price structure of oil and gas becomes a consideration to the plant operators.

Jan 1, 1980

By R. Didchenko

THERE are many methods described in the older literature which claim to produce anhydrous rare-earth chlorides in general. and cerium chloiide in

Jan 1, 1960

By Dale Dixon, A. R. MacPherson

The present comminution process in principle has remained more or less the same for the last 50 years. The majority of the changes have been in the fields of equipment improvements and size increases of prevailing systems. The development and utilization of completely new systems has virtually been non-existent. As energy and steeel costs increase and lower grade ores are mined, the comminution costs per ton of ore treated must improve accordingly or the operations will not be profitable. The chapter examines further developments in existing systems and touches on relatively unexplored methods of comminution appropriate for future needs.

Jan 1, 1982

By John J. Childress, Russell L. Cook

Stringent environmental regulations, which have limited the use of sludge ponds, coupled with the economic incentive to clean more coal or to add fine coal cleaning additions to existing preparation plants have increased the use of static thickeners in preparation plants. The Lamella Gravity Settler, sometimes designated Lamella Thickener, is a shallow depth sedimentation device which has been applied in a variety of industrial process and wastewater control projects in place of the conventional raked thickeners. This paper presents the theory and design of the Lamella Thickener, as well as describing the operating results from several full scale installations in a variety of Appalachian preparation plants.

Jan 5, 1978

By J. W. Goss, M. J. Coolbaugh

A survey of literature published in the U.S. on grouting indicates that most such work has been done to stop water flow in mines and for stabilizing foundations of various man-made structures. Apparently San Manuel is one of the first mines in this country to use grout extensively underground for the strengthening and stabilizing of ground about drifts, shafts, and stations.

Jan 3, 1961