Search Documents

DURING the early part of August, 1880, I was directed by Prof: J. P. Lesley, State Geologist, to assume charge of the geology and mapping of the Second Geological Survey of the anthracite coal-fields. I visited the region unineumbered by any instructions other than this, that I should submit a plan for making the sur- * In the practical application of this method I wish to acknowledge the valu¬able aid rendered by my assistant, Mr. A. W. Sheafer.

Jan 1, 1881

By W. Petruk, R. S. Boorman, R. Gilders

Approximately 33% of the silver in the Zn-Pb-Cu-Ag ore of Brunswick Mining and Smelting Corporation Limited is lost to the tailings and an additional 11% to the zinc concentrate for which no payment is received. 38% to 44% of this lost silver is carried by tetrahedrite, 28% by galena and 28% to 34% by a third silver carrier. The silver minerals acanthite and pyrargyrite have been identified in mill products and hence these are suggested as the principal third silver carrier(s) accounting for 13 to 20% of the silver in Brunswick ore. About 24% of this third silver carrier assemblage is lost to the zinc concentrate and 52% to concentrator tailings.

Jan 1, 1984

By Jerome C. Motz

Primary Crushers The types, sizes and number of crushers employed in a complete reduction system will vary with such factors as the volume of ore to be processed, the size of the mine-run lump material, the hardness of the ore bearing rock and the size and dimension required for the final product. Basically, for primary crushing there are only three distinct types of crushing equipment. These are the Jaw crushers, Gyratory crushers and Impact crushers, and they each have their own distinctive operating characteristics. Jaw crushers operate by squeezing the rock between the fixed and the movable sides of a tapered cavity. Variations of pitch and swing have been tried, but most Blake-type machines have a crushing angle of about 27° between swing and stationary jaws. The principle of which Gyratory crushers work is very simple. If a Cone is mounted on the upper end of a vertical shaft and the top of the shaft is held .stationary while the lower end is rotated eccentrically, the Cone will also swing eccentrically. If the Cone is enclosed in a suitable housing, it will swing toward and away from the housing walls-as it rotates. If the done and the housing walls are sufficiently strong and heavy, anything caught between them will be crushed.

Jan 1, 1978

By Tadao Nagai, Masao Sato

Electrochemical measurements have been carried out in an auto- clave to investigate the electrochemistry of hydrogen precipitation of nickel from acetate buffered solution. After having previously obtained the rate equation for this reaction we have now made a concentrated effort to explain the rate equation electrochemically. A saturated NaC1-type Ag/AgC1 reference electrode has been improved so that it can be used in an autoclave. Polarization curves for the reaction, [H2=2H+ + 2e,] on nickel electrode were measured in solutions free from nickel ions at 185°C, and the parallel curves were obtained by changing PH2 and pH for normal and reverse reactions, respectively. Polarization curves in nickel solutions were complex, probably because the potential of hydrogen electrode is close to that of nickel and of the nickel surface altered during polarization. Then the nickel electrode potential and the reaction rate were measured simultaneously during pressure reduction at various hydrogen pressures and at various nickel concentrations. The reaction rates in terms of current density were plotted to obtain the local polarization curves for reactions Ni2+ + 2e ? Ni and H2 ?2H+ + 2e. The anodic and cathodic local polarization curves exhibit potential dependency. Therefore it is likely that the pres- sure reduction can be regarded as a coupled electrodes reaction.

Jan 1, 1973

By P. F. Ahner, Leonidas Petrakis, Fred E. Kiviat

High gradient magnetic separations (HGMS) is a recently developed technique in which magnetic micron-size particles contained in a flowing fluid medium can be extracted from that medium. HGMS is presently utilized on a commercial scale in the kaolin processing and steel industries, and is being investigated for solid-liquid separations in numerous other processes. The performance characteristics of HGMS in the kaolin and steel industries are briefly summarized. A discussion of HGMS performance with respect to solids removal in a coal liquefaction process is presented to illustrate its applicability to difficult solid-liquid separations. Here, the properties of the solids suspended in the liquified coal are such that the HGMS separator achieves over 90% solids removal. The optimization of the HGMS operating parameters to yield these results will be discussed. To further illustrate the potential of HGMS, its performance with respect to the removal of oil and solids (over 98% removal) from a petroleum refinery process water effluent stream will be briefly considered.

Jan 1, 1980

AMONG the fellow prospectors of Black Jack Newman, locator of the claims that became the Miami mine, were J. D. Coplen and Bud Woodson. Woodson was in the district when the Bloody Tanks Indian massacre occurred, near the present town of Miami. He was a prospector long before Jack Newman worked in a mine, and for years he had done assessment work on some of the claims that Coplen acquired for his Inspiration company. Woodson recalls that a Scotch geologist from Morenci once visited his claims; and that the geologist tried to get the Phelps Dodge company interested in the property, but without success. Coplen interested some people in Kansas City in his claims that lay west of Newman's. He induced them to organize the Inspiration Mining Co., and by 1908 this company controlled 23 claims, which had been prospected in desultory fashion by a series of adits. One of these, near the Keystone property, encountered some lean copper-bearing rock, but later development failed to disclose any substantial quantity of ore at this particular point. Coplen, as general manager, in September, 1908, was negotiating with several exploration companies which at the time were on the lookout for low-grade copper properties. As a matter of fact, when J. Parke Channing visited Globe, in December, 1906, F. C. Alsdorf showed him the Inspiration claims as well as Newman's. Channing evinced little interest in an option on Inspiration because he could get so much better terms from Newman. He decided to concentrate his work on the Newman claims, with the idea that if he were successful in developing ore, he could later get Inspiration on terms at least equally good. Subsequently, the United States Smelting & Refining Co., which has since added "Mining" to its corporate name, took an option on Inspiration.

Jan 1, 1933

By Sunder S. Saluja

Man had to learn to break rocks as early as the Stone Age, when they formed his main source of raw material. He started with chipping and over the years has reached a stage where he can employ atomic blasts and break, with one blast, millions of tons of rock. In between these two extremes there have been several stages of development including firesetting, use of the expansion of water on freezing in chipped cracks in cold climates, the use of low or deflagrating explosive black powder in about the 17th century, the use of high explosives with the discovery of nitroglycerine in 1846 by Sobrero, followed by the monumental discoveries of the great Swedish scientist Alfred Nobel in the latter half of the nineteenth century. The attempts to develop a stronger and still stronger explosive force were accompanied by investigations to understand the mechanism of failure of rock so that the force could be used to the best advantage; the latter, of course, have lagged far behind the former. This is mainly due to the fact that the chemical reactions involving high explosives as well as the processes resulting in the breakage of rock take place at too great a rate to be studied with the equipment that has been only recently available. Moreover, the development of stronger explosive forces was prompted by military necessities in the past and competition, at present, among highly developed nations. With the development, however, of the new techniques such as micro- second photography, microsecond flash radiography, extremely high-speed movies, strain gage assemblies, electronic chronographs and other improved electronic techniques, the investigator has in the last decade or

Jan 1, 1968

By Alvin L. Langstaff, Harold D. Raymond

The design of entry systems and mining panels in room-and-pillar oil shale mines seeks to optimize extraction while ensuring both short- and long-term stability of mine openings. Important criteria for optimization include the definition of allowable roof spans and minimum pillar dimensions. Factors considered pertinent to the design of roof spans and pillars are discussed in this paper. They include, but are not limited to, physical properties and grade of the oil shale, depth of burial, presence and frequency of partings and joints and adverse effects of blasting. Also discussed briefly are some of the ventilation and production considerations in mine design.

Jan 1, 1984

By Eckley B. Coxe

(WITH FIGURES ON PLATES II, III, AND IV.) I DESIRE to call the attention of the Institute to two deep vertical shafts, which are now being sunk in Schuylkill County, Pennsyl¬vania, about 1 1/2 miles north of Pottsville. These shafts are of interest to the mining engineer, not only on account of the novelty of the method of sinking adopted, which promises to produce a revolution in that branch of mining engineering, but also as examples of the manner in which such work should be undertaken. GEOLOGICAL SKETCH OF THE TERRITORY TO BE WORKED BY THE SHAFTS AND REASON FOR SINKING THEM. The Mammoth or E Vein of the anthracite coal-measures in that part of the Schuylkill region near and north of the town of Pottsville lies at a great depth below the surface, and has, in consequence, never been worked in that locality.

Jan 1, 1873

By Richard D. Call

In any open pit, some slope instability can be expected, varying from bench sloughing to large-scale slope movement. Major slope displacements are preceded by small, but measurable, displacements and by other indicators of instability, such as tension cracks, rock noise, and changes in groundwater levels. A comprehensive monitoring pro- gram, capable of measuring and assimilating displacement related data, is essential for sound pit operation. The objectives of a pit slope monitoring program are 1) to maintain safe operational procedures for the protection of personnel and equipment; 2) to provide advance notice of instability so that mine plans can be modified to minimize the impact of slope displacement; and 3) to provide geotechnical information for analyzing the slope failure mechanism, for designing appropriate remedial measures, and for conducting future re-design of the slope. Surface displacement measurement using conventional survey equipment and extensometers has been the most widely used method, and it is still the most cost-effective. Tiltmeters and borehole inclinometers are also useful tools, and there are promising developments in micro- seismic monitoring. A monitoring system should have redundancy in both type and number of measurements, and be capable of rapid and effective dissemination of displacement information to those affected.

Jan 1, 1983

By Benjamin Moore

AT present the demands of the United States for strontium are met by imports from Germany, England and Canada, which vary considerably in proportions of ore and finished salts, in tonnage and in value. Statistics for the period 1926-1932 are given in Table 1. Domestic deposits are TABLE 1.-Strontium Imported into the United States, 1926-1932° Ore Chemicals Year Short Tons Value Pounds Value 1926 2,200 $58,159 5,433,044 $115,436 1927 1,356 58,711 4,233,816 149,383 1928 759 31,157 3,380,464 136,561 1929 973 45,505 4,578,327 196,233 1930 220 10,459 2,153,788 104,807 1931 (260 lbs.) 123 1,742,714 83,564 1932 5 276 469,481 20,910 a Mineral Industry (1934) 42, 61. known in many states, but the larger and purer ones are in the West, particularly in the desert region of southeastern California and western Arizona. These deposits are large enough to command interest, par-ticularly in consideration of future cheap power at the Boulder Dam. The deposits described in this paper were examined during an investi¬gation of the, mineral resources of the Boulder Dam region by the United States Geological Survey for the United States Bureau of Reclamation' in the spring of 1934. Mr. D. F. Hewett, who had general charge of the investigation, Mr. W. T. Schaller and Mr. M. I. Goldman contributed many helpful suggestions. Mr. N. H. Harshman assisted efficiently during the field work.

Jan 1, 1935

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William F. Lawrence

INTRODUCTION Cleaning fine coal sizes utilizing air currents in machines as the primary separating medium is called dry concentration or pneumatic cleaning. In 1947 approximately 18 million tons (16.38 million mt) of bituminous coal were cleaned by air machines; in 1965, 25.4 million tons (23.1 14 million mt); but in 1975, only 7 million tons (6.37 million mt). Table 11-1 shows the tonnages cleaned of bituminous coal and lignite in the United States by various types of equipment from 1938-1963. Table 11-2 shows only tonnages cleaned by pneumatic methods from 1964-1975. The decrease in tonnage to approximately 7 million tons (6.3 million mt) is due to a higher moisture content in the mined coal and the greater difficulty in cleaning the coal by air. There also was a definite trend to load raw coal at the mines, especially the slack which is the most expensive to clean due to the dewatering and drying requirements. While there have not been any applications of pneumatic cleaning in the anthracite field, its use has not been fully explored. The same is true for lignite and subbituminous coals.

Jan 1, 1979

By Kenneth B. Ray, George R. Gardner

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent, investigation developed similar processes, which were successfully used in

Jan 1, 1939

By Peter B. Scotland

The mines of the Arizona Copper Co. are situated in the Morenci-Metcalf copper district in southeastern Arizona. This copper-bearing district covers a triangular mountainous area of about 3 square miles, rising abruptly from the gravel plateau of the surrounding country. In this area, an immense intrusion of porphyry lias displaced, shattered, and engulfed the shales, limestones, and quartzites formerly bedded on the basal granite. Outcrops of oxide ore were discovered in 1873, and these surface ores were found to connect in depth with large bodies of high-grade oxide ores in the limestones and shales. The mining of these high-grade ores continued until about 1893, when their rapid exhaustion led to the discovery and exploitation of the low-grade sulphide ores in the adjoining porphyry. Methods of concentration were then devised and the low-grade ores finally rendered profitable. The Arizona Copper Co. and the Detroit Copper Mining Co., operating in the same district, were the pioneers in the successful development of the low-grade "porphyry" properties of to-day. The largest mines of the Arizona Copper Co. are the Humboldt and Clay at Morenci, and the Coronado, Metcalf, and King at Metcalf. These mines produce about 4,000 tons daily of concentrating ore containing from 2.5 to 2.8 per cent. copper. The topography of the country is very rugged and mining operations are conducted principally through adit levels. A few of the mines are opened by shafts, the deepest being 1,100 ft., in the Coronado mine. Ore Occurrence The low-grade sulphide ore occurs as: (1) disseminated deposits in the main stock of quartz porphyry; (2) lode deposits in fault fissures in granite. The high-grade oxide ores were found as tabular deposits in limestone and shale close to contacts with porphyry dikes. Low-grade oxide ore formed the outcrop of some of the sulphide orebodies; the majority of the outcrops, however, were barren.

Jan 1, 1915

By Klaus Emicke

The paper describes the lead refining process operated at Norddeutsche Affinerie (N.A.). Incoming materials are different grades of lead with varying percentages of impurities: Cu, Te, As, Sn, Sb, Bi, precious metals. The facilities are designed for charge-wise operation. After drossing, generally Te, As, Sn and Sb are removed substantially by the Harris Refining Process using fused NaOH. A certain selectivity during refining is achieved by controlled addition of NaNO3. Another refining step is decopperizing by means of elemental sulfur. Complete separation of Te, As, Sn and Sb is accomplished by chemical methods in a leaching plant. A Howard Press is used in the Parkes Process for desilverizing. After vacuum dezinking in kettle, Bi is removed, if required, by means of Ca and Mg. In an end refining step Ca, Mg and Zn are removed by having the lead melt treated with NaOH and NaN03. The refined lead as such, or in the form of special alloys, is cast by an ingot casting machine into 50-kg ingots. Zinc which is used as a precipitant in the Parkes Process is recovered by distillation from the high grade Ag-Zn-Pb crystals in Faber du Faur retorts while the Pb/Ag alloy is fed to the cupellation furnace. Ca and Mg are removed from the Ca-Mg-Bi crystals formed in the course of Bi removal, and the Bi-bearing lead is cast into anodes. The electrolytic lead refining facilities at N.A. are operated largely for the purpose of separating Pb and Bi. These facilities are also used particularly for the refining of Bi-bearing lead which had gone through the above process, but from which Bi has not been removed by Ca and Mg.

Jan 1, 1970

By George R. Gardner, Kenneth B. Ray

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent, investigation developed similar processes, which were successfully used in

Jan 1, 1939

By Eric Jette

IN order to control a chemical process by other than empirical, rule of thumb methods, two types of knowledge concerning the reactions involved must be available: (1) the thermodynamics of the reactions, and (2), by no means less important for efficient operation, the mechanisms and kinetics of the reactions. Information on the thermodynamic side enables the operator to decide upon initial and final conditions, whether heat must be .added or removed from the system, whether the reactions proceed farthest in the desired direction at high pressure or low, etc. Knowledge of the mechanisms involves the determination of the individual steps by which an initial set of reactants, under given conditions, proceed to give the desired final products and kinetic studies upon which the mechanisms are based give the speed at which each of these reactions or steps take place. Thus thermodynamic studies of a 'reaction enable the operator to control the direction and extent to which the reaction can proceed, while kinetic studies enable him to control rates and thus the time' efficiency of the operations. The thermodynamics set the limit to which the reacting system approaches; the kinetics tell how fast the system actually approaches this limit. The two types of information are complementary and not antagonistic even though in discussing the mechanism the introduction of thermodynamics is entirely needless and generally of no assistance, while in thermodynamic studies mechanism need not even be mentioned.

Jan 1, 1931

By F. P. Agterberg

It can be useful to model the mean grade values for a metal in mineral deposits containing that metal as representing the extreme value tail of a lognormal frequency distribution for the concentration values of the metal in common rocks of all types. Results for copper and zinc in the Abitibi area of the Canadian Shield are compared to results previously obtained for the Canadian Appalachian region. The lognormal model is also applied to a set of 162 large gold deposits in the Abitibi area. In the second part of the paper, 1311 large and small gold deposits in the Abitibi area are modeled as discrete events. By means of a newly developed spatial clustering model it is possible to predict the variances of random variables for frequencies of deposits in cells of different sizes.

Jan 1, 1981

By L. M. Cathles, W. Joseph Schlitt

A mathematical model describing the leaching of low grade industrial waste dumps in developed and solved by finite difference techniques. The leaching behavior of model dumps of different sizes, permeabilities, and waste characteristics, under different operating conditions, is then investigated using the model. It is shown that leaching is fastest for dumps 50-100 feet (15-30m) high, that permeability is very important for the effective leaching of large dumps, that slow leach kinetics of the waste may not be detrimental, and that the leaching of large dumps may be facilitated if leach solutions are preferentially applied to the hot, near-edge portions of the dump.

Jan 1, 1980

By D. W. Brunton

The object of the investigations and experiments here recorded was to obtain such information and data as would make it possible to determine the fineness to which crushing must be carried, in sampling gold- and silver-ores, in order to obtain results within an allowable limit of error.

Jan 1, 1896