Search Documents

By R. D. Daniels, T. G. Oakwood

A study was made of the effects of small quantities of hydrogen on the mechanical properties of colum-bium. Tensile specimens, hydrogenated to concentrations of 20 to 200 ppm, were tested at temperatures of 300°, 191°, and 77°K. Although hydrogen was found to have little effect on the strength of columbium, the ductility of Cb-H alloys was found to be quite sensitive to both hydrogen concentration and temperature. At 300°K, an abrupt loss in ductility occurred at a critical hydrogen concentration, although some ductility was observed beyond the tolerance limit. A similar result was found at a lower hydrogen concentration at 191°K. At 77°K, however, a more gradual loss in ductility with increasing hydrogen concentration was observed. Hydrogenated columbium was thus observed to undergo a ductile-brittle-ductile transition. Metallographic examination of fractured specimens revealed extensive porosity at both 77° and300°K which was a distinct function of hydrogen content. At 191°K, although some secondary cracking was noted, the amount of observed porosity was minimal. These observations are interpreted in terms of hydrogen solubility and mobility as a function of temperature and in the role of hydrogen in promoting growth of microcracks. lHE effect of hydrogen on the mechanical properties of the refractory metals is not, at present, completely understood. A number of studies have shown these materials to be susceptible to hydrogen embrittlement. Roberts and Rogers1 have found that vanadium can be embrittled by hydrogen. It was further demonstrated that fracture undergoes a ductile-brittle-ductile transition as the temperature is lowered from 150° to -196°C; i.e., there is a ductility minimum observed at a certain temperature. The ductility is increased by either raising or lowering the temperature from this point. A more complete study by Eustice and Carlson2 on vanadium containing 10 to 800 ppm placed the ductility minimum at about -100°C with variations reportedly due to hydrogen content and strain rate. Ductility minima have also been found at certain temperatures for tantalum containing 7 ppm H3 and 140 ppm H.4 At hydrogen concentrations above 270 ppm, however, the ductility return at low temperatures was considerably reduced.4 In the case of columbium, some disagreement exists in the literature. Eustice and Carlson,5 Wilcox et al.,6 and Imgram et al.4 failed to find a ductility minimum although a composition-dependent ductile-brittle transition was observed. Hydrogen concentrations in these investigations were 20 ppm,5 1 to 30 ppm,6 and 200 to 390 ppm.4 However, Wood and Daniels7 observed a rather pronounced ductility minimum at hydrogen contents ranging from 19 to 252 ppm. Those theories of hydrogen embrittlement involving the precipitation of diatomic hydrogen which have been applies to ferrous metals8-12 do not seem to be applicable to the case of columbium and other exothermic occluders. Such theories propose that extensive crack formation and propagation occurs by the precipitation and expansion of diatomic hydrogen at internal voids and microcracks. However, photomicrographs of hydrogenated columbium do not show any evidence of damage introduced by the sorption and precipitation of diatomic hydrogen; rather, at high hydrogen concentrations, a hydrogen-rich second phase is precipitated.13'14 In addition, a number of these theories require the development of high hydrogen pressures at voids in the structure.8'10'12 This does not appear to be feasible in the concentration ranges discussed in the aforementioned paragraphs. The possible interaction of atomic hydrogen with microcracks resulting from dislocation pile-ups15,16 remains in doubt since pile-ups have not been observed in bcc metals17 including columbium.18 Wood and Daniels7 have put forth the possibility that a hydride precipitation could be responsible for crack nucleation in columbium. Work by Longson19 has shown that hydrogen embrittlement of columbium parallels the bulk solubility limit; i.e., as the solubility increases, for instance with temperature, the amount of hydrogen necessary to cause embrittlement also increases. Although a hydride precipitation appears attractive as a means of nucleating microcracks in columbium, what require more intensive study are the low-temperature anomalies which have been observed, i.e., the ductile-brittle-d'ictile transition characteristics. Also, the hydrogen concentrations where embrittlement occurs are often below the bulk solubility limits determined by Albrecht et al.13,14 and Walter and Chandler.20 This work is an attempt to determine more definitively the effects of concentration and temperature on the mechanical properties of dilute Cb-H alloys. EXPERIMENTAL PROCEDURE Ultrahigh-purity columbium rods, obtained from the Wah Chang Corp., were cold-reduced by rotary swaging. A chemical analysis is given in Table I. The material was cut into cylindrical blanks 1.50 ±0.005 in. long. Individual specimens were either given a stress relief anneal at 750°C or recrystal-lized at 1200°C. Resulting microstructures were either a "bamboo" structure characteristic of a wrought material or a recrystallized structure with a grain diameter of approximately 100 n. All heat treatments were carried out in a vacuum of 10-5 Torr or less.

Jan 1, 1969

By E. A. Gulbransen, K. F. Andrew

The gas-metal reactions of zirconium are very interesting. The metal is extremely stable at room temperature to reactions with the several gases present in air and the metal will stay bright indefinitely. However, at temperatures of several hundred degrees higher the metal reacts readily with oxygen, nitrogen and hydrogen. This behavior, in addition to the fact that zirconium is one of the higher melting point metals which might have high temperature applications under the proper conditions, resulted in the work reported in this communication. There are several factors which indicate that zirconium might have good oxidation resistance at elevated temperatures. These are: (1) the high melting point of approximately 1860°C, (2) the high melting point of the oxide of approximately 2675°C, (3) the high degree of thermodynamic stability of the oxide to chemical reaction and the low decomposition pressure of the oxide and (4) the possible formation of a continuous oxide film since the volume ratio of oxide to metal is greater than unity. The unfavorable factors are: (1) the metal reacts to form nitrides, hydrides and carbides, (2) the oxide is soluble at elevated temperatures in the metal and (3) the oxide ZrO2 undergoes crystal structure transformations at high temperature. The oxidation resistance of this metal is not only a question of the rate of film formation but is complicated by the fact that the oxide and other reaction products dissolve in the metal which in turn will affect the physical and mechanical properties of the metal. The protection of the metal to nitride formation must be considered separately from the oxide problem. One unfavorable factor is that the volume ratio of the nitride to the metal is about unity. This indicates that a discontinuous film might be formed. This paper will present measurements on the rates of reaction of the metal with O2, H2 and N2 over a wide temperature and pressure range. The reaction in high vacuum and the stability of the several compounds formed will be presented. The results are correlated with fundamental rate theory and with the physical and chemical structure of the metal and film. Literature Although many papers have been published on the chemical reactions of zirconium with various gases, comparatively few are concerned with the protective nature of the metal and its reactions at normal pressures. The studies in the pressure range below 0.01 mm of Hg gas pressure are largely of interest in the nature of the adsorption of gases by hot filaments in high vacuum apparatus. The reactions of zirconium in this pressure range have been reviewed by Fast8 and by RaynOr.27 In spite of certain differences of opinion as to the maximum adsorption temperatures for various gases, the low pressure range is qualitatively understood. Some of these papers will be mentioned briefly here. 1. LOW PRESSURE Ehrke and Slack' find that oxygen reacts above 885°C and hydrogen above 760°C. Nitrogen does not react up to a temperature of 1527°C. Fast9 on the other hand observes that oxygen is absorbed above 700°C and nitrogen at temperatures exceeding 1000°C. Hydrogen is absorbed from 300" to 400°C and liberated between 500" and 800°C. It is readsorbed at 862°C and released above 862°C. Hukagawa and Nambo22 find a rather complicated picture for the absorption of oxygen. A rapid initial absorption is found between 180" to 230°C. Further oxygen is not taken up until a temperature of 450°C is reached. The optimum temperature for complete absorption is 650" to 700°C. Nitrogen is found to be completely adsorbed at 600°C. However some of the gas is evolved at higher temperatures. Their data on the absorption of hydrogen indicate some of the gas is removed at 550°C. Guldner and Wooten17 in a study of the low pressure reactions of zirconium with various gases observed that the reaction with oxygen occurs at temperatures above 400°C and that the oxide is formed. The reactions with carbon monoxide and carbon dioxide occur rapidly at temperatures of about 800°C with the oxide and carbide being formed. Zirconium reacts at temperatures of 400°C slowly and at 800°C rapidly to form the nitride and with hydrogen and water at 300°C to form the hydride and a mixture of the oxide and hydride respectively. 2. NORMAL PRESSURE DeBoer and Fast3 in a study of the electrolysis of oxygen in zirconium find that the metal absorbs up to 40 at. pct of oxygen without forming a new phase. The solubility of nitrogen in the lattice has been studied by de Boer and Fast4 and Fast10 and is found to be considerable. At higher temperatures the oxide dissolves in the lattice at an appreciable rate according to Fast10 and the zirconium surface becomes active. De Boer and Fast4 and Hägg18 have studied the solubility of hydrogen and find that at room temperature the solubility corresponds to ZrH1.95 Desorption occurs on lowering the pressure. Hydrogen is stated to be more soluble in the ß-form and the

Jan 1, 1950

By AIME AIME

IN accordance with the provisions of Art. XII, See. 3, of the By-laws of the American Institute of Mining and Metallurgical Engineers, the Board of Directors hereby give notice of their intention to amend the By-laws as follows : Art. V, Sec. 2. Amend by substituting the word "senior" for ('first" before the words "Vice-president" in line two of the third paragraph of said section which relates to the calling of special meetings of the Board in the absence or disability of the President.

Jan 1, 1930

By ALFRED KAUFFMAN

NO matter what position we hold, workman, foreman, superintendent, manager, president, or what not, let us fail to give or to make good products, then see how quickly we'll be called to account for- our work by the buying public. The waves of progress taught us that millions were wasted in unnecessary strikes-we also learned that many losses were due to neglect on the part of manufacturers to give the same consideration and attention to the human element of their factory as they gave to their machinery. The employees learned also that the employer was their agent who found purchasers for the product of their labor. So between the two we learned that many years of labor were needed in order for a worker to recover his wasted savings, or for the manu¬facturer to replenish his loss. Treat 'em rough, and tell 'em nothing, was not very far from the true relationship between management and employees in manufacturing plants in the early days. Today just exactly the opposite views are held by executives whose function is the handling of employees. Men today want to know what it is all about. They are intelligent enough to comprehend the facts, and to use them constructively, and it is good business to give them the information.

Jan 1, 1929

By W. E. Bearce

The recent concern for the recovery of even the finest fractions of coal preparation plant feeds has created needs for new equipment. Thermal dryers currently available have difficulty reducing the filter cake moisture on down to the desired point. This difficulty involves 1) the physical problem of handling this wet, sticky material and making each particle accessible to the hot gases, and 2) removing the extremely fine dried particles from the cooled gases. The dryer described in this paper handles the first of these problems, and eliminates the second by the substitution of steel balls for air as the heat transfer medium. As a general statement, the cost of preparing coal for market is inversely proportional to the size of the lumps or particles. In the not too distant past the finer sizes were discarded as being uneconomical to treat and this practice might be still continuing if it were not for the insistence of the public that this material be kept out of our streams. This being the only cost-free outlet, the disposal of fine refuse became a significant item of expense in every preparation plant. When this happened it was only reasonable to look to the recovery of the values in this material, not only to defray this expense, but to reduce the tonnage which had to be wasted. There seemed to be no device available suited to reducing the moisture in this material to what the market requires. All of the fine coal dryers commonly employed make use of air to bring the heat of combustion into contact with the coal particles. Any device employing air as a heat transfer medium, has the following two strikes against it in attempting to handle 28 mesh by 0 filter cake: 1) It is practically impossible to bring the hot air into intimate contact with the enormous number of fine particles stuck together in the cake. 2) Even if this can be effected, it is impossible to remove the dried coal from the air. A wet scrubber must be employed, the discharge of which must go back to the filter and dryer as a circulating load of the most objectionable sort, being the extreme fines. Various compromises have been used to cope with the problem of drying this relatively small tonnage of high moisture coal. Often some of the dried coal is mixed back with the feed to the dryer in an attempt to make the mixture more handleable and more available to contact with the hot air than the filter cake alone would be. This may help to some extent with the first problem but it does nothing about the second and a dryer operated in this way has to be oversized. Sometimes the filter cake is mixed with a coarser fraction for the same reason. Here again, while this may make a mixture (the particles of which are more readily brought into contact with the hot air), the problem of getting the fine coal out of the air remains and a larger percentage of the total coal to be dried is handled by the most expensive means. Mechanical dewatering has accounted for more and more of total coal drying lately and in many cases would satisfactorily handle the whole load, down to 28 mesh, if there were a means available for doing a good job on the —28 mesh by itself. The dryer which is the subject of this paper was designed expressly for doing this job — drying fine material by itself regardless of how wet it may be to start with, how fine it may be, or how gummy and sticky these properties in combination may make it. The essential features are depicted in Fig. 1. A rotating cylinder is supported on a frame in such a way that one end may be raised or lowered by hy-

Jan 1, 1968

By H. A. Fisch, A. J. Opinsky, J. L. Bartos

Fort?-six- two-grain bounduries were studied in doped tungsten 1amp wire that had been heated to 3450°K very vapidly. Back-reflection Laue photograms were taken of the grain boundary partners and solved, using a computer. The resulting distribution of large-grain orientations was analyzed. Rotational axes were calculatedfor each grain boundary pair. The axes of least rotation show an anisotropy of rolalional angle. WhILE the orientations of large grains in straight doped tungsten wire have been studied extensively, little has been done to characterize the boundary that separates them. Rosi.1 upon seeing the jagged interlocking boundary in doped tungsten wire. inferred that the grains should have a preferred orientation, and proved it. He interprets his data as indicative of a single ideal orientation—(531)— being parallel to the wire axis. Rieck2, 3 and Mannerkoski' have essentially confirmed this finding. Opinsky, Orehotsky, and Siegle argue that the data suggest that (211)—a plane-is parallel to the wire axis instead. This (211 ) contains the (531). and hence would appear to be a more general case.5 Ahlborn and wasserman6 report that their orientation data stretch from (110) through (531) to (311). This path is the locus of {211 Recently. Opinsky has suggested that the data can be interpreted as a series of ideal orientations that can be related by coincidence relationships to the (110) fiber texture. All these investigators have determined the orientations of the large grains by the back-reflection Laue technique, and they have all obtained similar results. Only Rieck5 as methodically looked at the large grains along a wire. He was apparently not concerned with the relationships of the large grains across their common boundary, but only with their individual orientations. This research was undertaken to fill this gap in the under standing of the mechanical properties of tungsten wire. Only the crystallographic aspects of the problem will be reported here. In addition, the large number of large-grain orientations, which was accumulated in this study. will also be analyzed. EXPERIMENTAL MATERIAL AND TECHNIQUES All of the data were obtained from four pieces of the same 7-mil-diam General Electric tungsten lamp wire. Twelve-inch lengths of the cleaned wire were heated in vacuum by the flick of a switch to 90 pct of the amperes necessary for fusion (a temperature of approximately 3450°K) and held for 1 min. On the basis of other data. it is estimated that the rise time is of the order of 0.5 sec. The four pieces of wire could have come from anywhere within about 18 ft of wire. Consecutive segments of each piece of wire were mounted in bakelite and polished metallographically The polishing procedure followed that described by woods. "nly boundaries between two grains that each occupied the entire cross section of the wire were photographed and X-rayed. The metallographic sample was mounted accurately with respect to the X-ray unit. Steps were taken to read the films as accurately as possible with the conventional Greninger net. The data were then entered into computer programs that solve the Laue film by precisely the same techniques that are used in the solution of the film by means of the stereographic projection. The use of the computer has probably shifted the main source of error from the stereographic plot to the reading of the film. On the basis of several experiments, it is thought that the error associated with the entire process, from mounting the sample through the computer solution, is of the order of about one-half degree. The output of the computer is the direction cosines of the fiducial direction (the wire axis) and the locations of the three cube axes. The former data were used to calculate the differences in orientation between the two grain boundary partners, and the latter were used in the calculation of the rotational axes that could bring the two grains

Jan 1, 1970

By W. L. McMorris, A. H. Brisse

IN the last several years the coal industry has intensified its effort to solve the growing problem of cleaning and recovering fine mesh coals. On one hand these has been increasing civic pressure for cleaner streams, and on the other hand there has been increasing production of fine mesh coal, resulting directly from adoption of the modern mining methods so essential to the economy of the coal mining industry. Cleaning fine coal with the same precision possible with coarser coals is a difficult task, and for coals finer than 200 mesh it has been impractical. Furthermore, the inclusion of —200 mesh material in the final product markedly increases costs of de-watering and thermal drying, which are necessary steps if coal is to meet market requirements. Consequently these extreme fines have generally been wasted. As a result, problems have been created in many districts because there has not been enough area for adequate settling basins. Wasting of coal in the -200 mesh slimes may account for a loss in washer yield equivalent to 2.0 to 2.5 pct of the raw coal input. With rising mining costs the value of such a loss is constantly increasing and a need for a better solution to the fines problem becomes more pressing every day. From an operating viewpoint, also, continuous removal of extreme fines from the washing plant circuit permits good water clarification practice, improving significantly the overall cleaning efficiency. The obvious desirability of recovering a commercially acceptable coal from washery slimes prompted U. S. Steel Corp. to investigate the merits of the Convertol process developed in Germany." Although this process has been used commercially in Europe for some time, little if any consideration has been given to its possible adoption in the U. S. until very recently. Fundamentals of the Convertol Process: In the Convertol process, droplets of dispersed oil are brought into intimate contact with the solids suspended in the coal slurry to be treated. This contact causes oil to displace the water on the surface of the coal by preferential wetting, or phase inversion, after which the coal particles are allowed to agglomerate in a manner permitting their re- moval from the slurry by centrifugal filtration. The clay and other particles of mineral matter suspended in the slurry do not have the affinity for oil the coal particles have. Consequently the oil treatment is preferential to coal to the extent that more than 95 pct of the oil used reports with the clean coal recovered. Figs. 1 through 3 will clarify the steps involved in the process. Fig. 1 shows the suspended material in the slurry to be treated, which is a thickened product containing 40 to 45 pct solids. Oil is now injected into the slurry under vigorous agitation to produce good oil to coal contact conditions, which result in preferential oiling of the coal particles. These coal particles are then permitted to agglomerate by gentle stirring in a conditioner to form flocs, as shown in Fig. 2. At this point in the process the agglomerated oiled coal can be washed and partially dewatered on a vibrating screen, as shown in Fig. 3. Finally, the washed flocculate can be further dewatered in a high-speed screen basket centrifuge or in a solid bowl centrifuge. Commercial Application of the Convertol Process in Germany: The original Convertol process was developed by Bergwerksverband zur Verwertung von Schutzrechten der Kohlentechnik, G.m.b.H., a German research organization controlled by the Coal Operators Assn. of the Ruhr Valley. The process as reduced to commercial practice in Germany' is shown in Fig. 4. In this process a thickened slurry (40 to 45 pct solids) mixed with a predetermined percentage of oil is fed from a surge tank to the phase inversion mill. After the phase inversion step, the slurry is usually discharged directly to a highspeed screen centrifuge. From 3 to 10 pct oil is used, depending on type of oil, size consist of coal to be recovered, and operating temperature. The top size of fine coal cleaned in Germany by the Convertol process is limited by the size of the openings in the centrifuge screen basket. Any mineral matter coarser than the basket opening, which is generally 60 to 80 mesh, must remain with the oiled coal. If the coal fines have been effectively cleaned down to about 80 mesh, the cleaning performance of the process is practically unaffected by the presence of coarse coal particles. However, since recovery of coal much coarser than 80 mesh is mow economical by conventional methods, it normally becomes more costly to allow substantial percentages of this coarse coal in Convertol process feed. Where the general plant layout does not permit effective cleaning of coal sizes down to 80 mesh or lower. there is some justification for a coarser Con-

Jan 1, 1959

By H. Biloni, B. Chalmers

Metallographic studies of the segregation of solute in and near the surfaces of chill-cast alloys have shown that, under sufficiently severe conditions, nucleation on the cold mold surface is followed by the formation of a disc of solid of the same composition as the liquid. This disc is surrounded by two concentric rings in which the concentration first decreases and then increases. The discs and rings are surrounded by a region in which arms of low solute concentration separate regions of high concentration. These arms start at the periphery of the outer ring and are initially radial; they make a gradual curved transition from the radial direction to a crystallographic direction. A normal dendritic substrcture is established beyond the position at which the arms have become crystallographically aligned. When the cooling is less severe, the disc becomes less irregular in shape and has a concentration minimum at the center. The term "Predendritic" is proposed for these transitions. A qualitative explanation is outlined for the phenomena observed at the surface and in the equiaxed region of the ingots. It is well-established1-' that the normal mode of solidification for alloys under most conditions is dendritic. A characteristic of dendritic solidification is the growth of rods or plates in specific crys-tallographic directions. The remaining liquid solidifies later, usually with a higher concentration of solute than the original liquid. Very little is known, however, about the transition from a crystal nucleus until the dendritic pattern is established. It is clear that there must be a transition because the nucleus is much smaller than the characteristic spacings found in the "steady-state" structure. And it also seems clear that the initial conditions must be important since the undercooling existing during the nucleation of the grains has a remarkable influence upon the grain size4 and the segregation pattern. The present paper reports a study of the micro-segregation in regions where crystals have nucleated, and the conclusions that can be drawn regarding the early stages of growth, in connection with the details of the solidification process. Aluminum of 99.993 purity, A1-Cu alloys containing 0.5 to 20 wt pct Cu, and Pb-Sn alloys with 5 wt pct Sn were cast and examined metallographically at the as-cast surface, close to the surface, and in the interior after casting. The alloys were cast from controlled temperatures against surfaces at different temperatures ranging from room temperature to approximately the liquidus temperature of the alloy. The surfaces were, in various experiments, graphite, stainless steel, copper, and aluminum. The methods used for metallographic examination were as follows. 1) The Nomarski phase contrast interferometer6 was used to obtain information on the topography of the as-cast surface. 2) The distribution of any solute present in A1 99.993 pct and copper in the A1-Cu alloys was studied by the anodic film technique originated by Lacombe and Mouflard7 and previously applied in the study of the solidification of aluminum by Biloni.8 The electropolished surface of the specimen is anodized under controlled conditions so that the thickness of the oxide film and therefore the interference colors under white light are sensitive to the local composition. This technique was applied to the as-cast surfaces and to metallographically prepared surfaces from the interior. 3) If in Al-Cu alloys, the surface is anodically oxidized for several minutes, instead of seconds as in the color-film technique, the copper segregation is outlined by a different level with respect to the matrix. This method is less sensitive but complementary to that for the color films. 4) The distribution of copper revealed and mapped by the metallographic techniques was confirmed by electron probe. 5) In samples with high concentration of copper, evidence for the copper distribution could be seen optically after electropolishing.

Jan 1, 1965

By Ashok K. Sinha

During the course of an in~*estigation into the occurrence of ordered AB3 structures, the following new phases have been found —CrRh3 (AuCu3 type), CrCo3 (MgCd3 type), HfCo4 (Ths Mn23 type), and WPt, MoPh type). The composition of the TiPt3-x phase (TiNi, type) is close to Ti23Pl77. The alloy chenzistry of transition rnetal AB3 structures is rezliewed in the light of electron concentration correlations of hex-agonality recently obtained for quasi-binary alloys. The relatizte colurne contraction in the AB3 structures increases with increasing difference in volume of the conzponents. A family of ordered close-packed layered structures is formed by stacking identical layers of composition AB, in various sequences, such that the coordination is twelvefold throughout and there are no A-A contacts. Previous work' on quasi-binary AB3 alloys has led to the conclusion that the stacking sequence of the AB, structures changes with increasing radius ratio RA/RB from a purely cubic, through different mixtures of hexagonal and cubic stacking to a purely hexagonal stacking. However. for binary AB3 alloys, a correlation between the type of the crystal structure and the position of the components in the various volumns of the periodic table has been noted.2-5 It has been noted6 that this correlation appears to hold even though the radius ratio RA/RB may vary over a considerable range with the location of the components in the three long periods. Another study7" of several quasi-binary systems led to the conclusion that an increase in hexagonality of the stacking is associated with increase in the electron concentration e/a. as defined by the average per atom of the total number of electrons outside the inert gas shells. In apparent conflict with this conclusion, it is known that seven binary alloy structures isotypic with TiNi3 which is 50 pct hexagonal occur at a higher electron concentration (e/n = 8.5) than that (e/a = 8.25) for the 100 pct hexagonal MgCd3 type structure present in seven binary AB3 alloys. Table 111. In the present work, an investigation into the occurrence of binary AB3 structures in transition metal alloys was made, and a survey of binary AB3 structures is presented. EXPERIMENTAL The starting materials were pure metals of 99.9 wt pct purity. The alloys were arc-melted under partial pressure of argon and annealed in sealed silica capsules lined with molybdenum foil under argon at- mosphere. The total weight loss upon melting and subsequent annealing was always less than 1 pct and hence the alloys will be referred to by their intended (unanalyzed) compositions. Wherever the constitution permitted. the alloys were given a homogenizing treatment at 1200°C (3 days) prior to annealing. Unless otherwise stated all alloys were annealed at 900°C for 1 week and water-quenched. Sometimes the final annealing treatment was carried out on powders to accelerate the attainment of equilibrium. X-ray powder patterns were taken using a Guinier-de Wolff focusing camera (CuK, radiation) or an asymmetrical focusing camera (Co or CrK, radiation). For lattice parameter determination. internal silicon standards were employed. The intensity calculations were made using a Fortran IV program written by Jeitschko and parthe.9 RESULTS Twenty AB3 and three AB4 alloys were investigated. Table I lists the crystallographic data on some of the intermediate phases encountered in the present work. Table II contains the X-ray data for HfCo, (Th,,Mn,, type). The positional parameter, x. was assumed to be 0.378. the value for Th6Mnn2310 The X-ray pattern of ZrCo, was very similar to that of HfCo, and the previous structure determination of ZrCo, by Kuzma el al." was confirmed. Ordering in the alloy CrCo could be ascertained by the presence of only one weak super lattice line (101). the others being too weak presumably owing to the small difference in the scattering powers of chromium and cobalt. This line was observed in the X-ray pattern of powder from the massive sample annealed at 830°C (7 days) after the powder had been reannealed at 600°C (24 hr). The diffraction pattern of the powder similarly reannealed at 830°C (24 hr) contained only the lines due to a mixture of hcp and fcc Co(Crj solid solutions. Therefore, it appears reasonable to assume that O2 and/or N2 contamination which would be less likely to occur during the 600°C anneal was not responsible for the observed weak reflection. Also. this reflection cannot be identified with any of the strong lines of the neighboring s phase which is present in the Co-Cr system at higher chromium contents. The composition corresponding to the TiNi3 structure observed by Raman et al.12 in the two-phase alloy Ti,zt,, has been established in the present work as being between There was satisfactory agreement for the low-angle lines (up to d = 1.997A) between the observed diffraction pattern of TiCua and that calculated assuming the ZrAu, structure. as recently proposed by Pfeifer-et a1.I3 However. some of the superlattice lines. e.g., at d = 1.937 and 1.919A. predicted by the ZrAu, structure were not actually observed eve? though neighboring lines. at d = 1.947 and 1.986A. of comparable calculated intensity were present. The ZrAu

Jan 1, 1970

By E. S. Fisher, L. C. R. Alfred

The elastic anisotropy factors, c4,/c6,, c3,/cll, and c12/cl,, for hcp metal crystals vary significantly among the dgferent unalloyed metals. Significant variations with temperature are also found. The effects of elastic anisotropy on the dislocation in an elastic continuum with hexagonal symmetry have been investigated by computing the elasticity factors for the self-energies of dislocations in fourteen different metals at various temperatures where the elastic moduli have been reported. For most of the metals the effects of the orientation of the Burgers vector, dislocation line, and glide plane are small and isotropic conditions can be assumed without significant error. Significant effects of anisotropy are, however, found in Cd, Zn, Co, Tl, Ti, and Zr. The elasticity factors have been applied in the calculations of dislocation line tensions, the repulsive forces between partial dislocations, and the Peierls-Nabarro dislocation widths. It is predicted that the increase in elastic anisotropy with temperature in titanium and zirconium makes edge dislocations with (a), (a + c), and (c) Burgers vectors unstable in basal, pyramidal, and prism planes, respectively. The probability of stacking faults forming by dissociation of Shockley partials in basal planes also decreases with increasing c4,/c6, ratio, when the stacking fault energy is greater than 50 ergs per sq cm. The widths of screw dislocations with b = (a) in titanium and zirconium increase very significantly in prism planes and decrease in basal planes as c4,/c6, increases. The effects of elastic anisotropy on various dislocation properties in cubic crystals have received considerable attention during the past few years. In the case of cubic symmetry the departure from isotropic elasticity depends entirely on the shear modulus ratio, A = 2c4,/(cl, —c12); i.e., the medium is elastically isotropic when A = 1. Foreman1 showed that an increase in the ratio A produces a systematic lowering of the dislocation self-energy for a given orientation and Poisson's ratio. ~eutonico~, has shown that large anisotropy can have a marked effect on the formation of stacking faults by the splitting of glissile dislocations in (111) planes of fcc and (112) planes of bcc crystals. ~iteK' made similar calculations for (110) planes of bcc metals. Both studies of bcc metals showed that the large A values encountered in the alkali metals tend to reduce the repulsive forces between Shockley partial dislocations. In fcc metals, however, A does not vary over the large range encountered in bcc metals; consequently, the effect of A on the forces between Shockley partials is masked somewhat by the differences in Poisson's ratio between metals. The effect of A on the line tension of a bowed out pinned dislocation has also been investigated for cubic crystals, first by dewit and Koehler5 and more recent- ly by Head.6 In both cases the line energy model is applied and the core energy is not taken into account, thus making the conclusions somewhat tenuous with regard to the physical interpretation. Nevertheless, the fact that a large A decreases the effective line tension is clearly evident and the tendency for large A to produce conditions that make a straight dislocation unstable (negative line tensions) also seem evident. Head, in fact, shows visual microscopic evidence that stable V-shaped dislocations occur in 0 brasse6 For hcp metals the definition of elastic anisotropy is more complex and, furthermore, significant deviations from an isotropic continuum are found among a number of real hcp metals, especially at higher temperatures. The present work was carried out to survey the effects of elastic anisotropy on the elasticity factors, K, that enter into the calculations of the stress fields around a dislocation core. Some isolated analytical calculations have previously been carried out for several hcp metals but they are restricted in the dislocation orientations and temperature.8'9 The present computations are based on single-crystal elastic moduli that have appeared in the literature and consider various orientations requiring numerical computations. The results are then applied to survey the effects of temperature on the dislocation line tension and dislocation splitting in hcp metals. PROCEDURE Anisotropy Factors. The degree of elastic anisotropy in hcp crystals cannot be described by a single parameter, such as the A ratio in cubic crystals. The following three ratios must be simultaneously equal to unity in order to have an elastically isotropic hexagonal crystal: The magnitudes of these ratios at several temperatures, as computed from the existing data for the elastic moduli of unalloyed hcp metals, are given in Table I. There are no cases of complete elastic isotropy, but the large anisotropy ratios encountered in the cubic alkali metals are also missing. There are, however, several significant differences among the hcp metals, the most notable being the relatively small A and B ratios in zinc and cadmium and the differences in the magnitudes and temperature dependences of A. It has been noted that the temperature dependence of A has a consistent relationship to the occurrence of the hcp — bcc tran~formation. For cadmium, zinc, magnesium, rhenium, and ruthenium, A is less than unity at 4'~ and, with exception for rhenium, decreases with increasing temperature. In the case of rhenium, A has essentially no temperature dependence between 923' and 1123"~, so that it is clear that A does not approach unity at higher temperatures. Cobalt is similar to the above-mentioned group of metals in that it also does

Jan 1, 1969

By J. G. Patchett, R. W. Rausch

Fresh waters and the presence of clay in many Rocky Mountain and West Coast sands require special methods of log analysis. Archie's saturation equation requires addition of a shale correction term, and the SP equation must also be modified to account for clays. Suitable equations were developed several years ago, but have not been widely used due to the algebraic complexity. A computer-oriented method has now been developed to overcome this problem. The basic shaly sand equations are rearranged in four different ways to permit solution for various sets of available input data. Essential to application of the method is the correction of observed SP values to those that would be observed if the resistivity of the formation waters were exactly interchangeable with the activity. A graphic method for doing this is given. Where conditions require consideration of the effect of clay in the sands, the method presented has been found to improve the accuracy of water-saturation determinations. INTRODUCTION Log interpretation in many Rocky Mountain and West Coast basins is complicated by rapid vertical and lateral changes in water resistivity. Calculation of formation water resistivity from the SP curve becomes difficult in zones that contain clay, since changes in SP deflection may be due to changes in either clay content or water salinity. In hydrocarbon-producing reservoirs, the problem is further complicated because hydrocarbon saturation also reduces the SP.1 A log interpretation system using computers has been developed to provide a solution to this problem, based on equations proposed by de Witte.2 Four different simultaneous solutions of de Witte's equations have been made. Each solution method uses a different set of input data as independent variables. Thus, a choice of solution method is possible, depending upon the logs run and the availability of other data. Two of the solutions do not require a knowledge of water resistivity. This system is intended to be used primarily in multiple sandstone-shale sequences of low and moderate resistivities where the principal contaminant in the sandstones is clay. However, where sufficient regional data are available, interpretation in single-zone sandstone reservoirs can also be improved by using the method. THEORY AND HISTORY OF SHALY SAND ANALYSIS The log interpretation formula originally proposed by Archie3 in 1941 is applicable only to rock-fluid systems wherein the rock has negligible electrical conductivity. In 1949, Patnode and Wyllie4 showed that if the rock itself can be considered conductive due to the presence of clay, a different calculation approach is necessary. During the following years, this problem was investigated at great length, as was the related problem of the effect of rock conductivity on the SP.5-11 These investigations established functional relationships between SP, resistivity, water saturation and water resistivity for such a formation. Refs. 2 and 12 provide summaries of these studies. Unfortunately, practical use of these relationships required that water resistivity be known independently from the SP. Although log interpretation methods for rock systems containing clay were proposed at that time,' they were not generally accepted for routine use. There are three principal reasons for this. First, in many field situations involving high-salinity water, rock conductivity may be neglected (even if present) without introducing appreciable error. This may be seen by considering the following expression for waier-saturated rock.' 1/R2=1/R1+1/FRn....(1) where 1/R, is conductivity due to clay. As Rw becomes small, I/FRw becomes much greater than 1/R, which may be neglected. Where 1/R, may be neglected, the sandstone is called clean. If the term may not be neglected, the sandstone is termed dirty or shaly. For resistivity purposes, the classification between clean and shaly sands then depends not only upon the conductivity due to shale in the sand, but also upon the resistivity of the associated water (shale is used here to mean surface condition due to disseminated clay). A sand of given conductivity might safely be treated as clean in association with high-salinity water, but would require shaly sand methods if associated with fresher waters. Shaly sand methods are not required in many areas having saline waters; but in Rocky Mountain and West Coast sands having relatively fresh waters (often more than 0.3 ohm-m resistivity at formation conditions), the shaly sand methods are needed. Errors Rw calculations from the SP due to the presence of shale are likewise related to water salinity. In saline water formations drilled with fresh mud, the ratio of mud filtrate resistivity to water resistivity is high, the SP is large and the presence of shale can introduce large errors in water resistivity calculated by the conventional method. When the resistivity ratio is low, the errors are smaller. At zero SP, no error would result from shale. Thus, from the SP viewpoint, a given rock could be shaly if associated with a saline water, and clean in association with a fresh water, which is the opposite of the resistivity-oriented definition above.

By B. S. Butler

A. D. Mutch (Falconbridge Nickel Mines Ltd., Ona-ping, Ontario)—This contribution is prompted by the fact that the writer has recently published an article'!' which has in part the same general conclusions as B. S. Butler's, namely, the form of the standard mineral paragenesis in hypogene deposits and the parallel transition from early high temperature acid to late low temperature alkaline or neutral solutions. Since the writer also recognizes that he is not fully qualified to discuss the formation of ore deposits as a chemical problem, this discussion will be limited to summarizing other observations and will suggest how Butler's Table II might be made more effective. The form of Butler's table is not unlike that widely used by European geologists'" in which the various minerals are related to the types of ore fluids—peg-matitic, pneumatolic and hydrothermal. Thus the decrease in temperature and change in pH of the ore-bearing fluids as recognized by Butler may also be paralleled by perhaps even greater changes in composition, density, and character. W. H. Newhouse's article:" on the sequence of hypo-gene ore mineral deposition is still one of the most complete analyses of the problem. In it he makes four major observations: 1) The order of O, S, As, Sb is the same as their increasing atomic weights and the same as their melting points. 2) The order of the metallic elements is the same as the Schuermann series. 3) The general mineralogical order is paralleled by decreasing heats of formation. 4) The order is generally in decreasing hardness, higher metal content, and higher specific gravity. The order of 0, S, As, and Bi is also the same as their relative abundance. Another point worth mentioning about this series is that As, Sb, Bi, when abundant, often substitute for sulfur in the early pyrite-like minerals, whereas later in the sequence these elements appear to act more like metals. This behavior may be a further indication of the acid character of the early fluids. C. J. Sullivan"' has attempted to show that the sequence of the metallic elements is related to the order of their melting points and has discussed the interrelationship of the different types of bonding of sulfo-phile and oxiphile elements in minerals. Items 3 and 4 might best be summarized by saying that bonding of the minerals in the series appears to be from ionic to covalent to metallic, the early minerals being light in weight, hard, and near-transparent; the intermediate minerals of intermediate weight, semi-transparent, and semi-conducting; and the end minerals heavy, soft, and malleable, opaque and good conductors. A rapid fall in temperature has been assumed to be the cause of ore deposition in many deposits. Perhaps this in turn is the effect of a rapid release of energy in the form of pressure release and change of volume, the first minerals to form being those with the highest heats of formation which absorb the released energy the most rapidly. Butler's Table II could probably be streamlined and made more effective if the listed compounds were assembled as mineralogical groups as in Dana. Thus the sulfides, arsenides, antimonides, bismuthides, and sulfa salts could be arranged in AX,, AX, A2X2, etc. groups. Since these are continuous substitution series, in which the fields of stability and the heats of formation of the various individual minerals can be fairly regarded as similar, this should be accomplished with no loss of clarity. The occurrence of the individual minerals and the precise sequence of the mineral deposition in any one deposit is probably more dependent on the concentration and relative abundance of the component elements. The assembling of geological data in tabular form such as Butler's Table II will continue to be a very effective method of studying geological phenomena. The importance of this particular problem has been pointed out by C. F. Park,% who concludes that understanding of mechanisms of the standard paragenesis and interrelated problems of mineral zoning in space and time is one of the major keys to classification of ore deposits.

Jan 1, 1959

By R. L. Fullman

IN the investigation of metallurgical transformations and the relationships between microstructure and properties of metals, it frequently is desirable to obtain a measurement of the relative amounts of the various phases present and of the mean size of particles into which each phase is dispersed. The relative amounts of the phases can be measured by the classical methods of area, lineal, and point analysis,1-5 in accordance with the principle that the volume fraction of a phase, the fraction of a polished cross section occupied by the phase, the fraction of a random line occupied by the phase, and the fraction of randomly arrayed points occupied by the phase are all equal. The validity of this relationship depends only on the attainment of a truly random sample of area, length, or points, and not on the size, shape, or distribution of the particles constituting the phase. Smith and Guttman8 have derived a relationship between the interface area per unit volume S, and the measurable quantities L., the interface length per unit area on a cross section, and NL, the number of interfaces per unit length intersected by a random line. Their equation, Sv = — L8 = 2NL is also valid regardless of the distribution of particle sizes and shapes. In contrast to the situation concerning measurement of relative fractions of phases and of interface area, the measurement of particle sizes in opaque samples has not been subjected to a complete analysis. It has been common to measure some lineal or area dimension of particles on a polished cross section and to use the mean value as a qualitative measure of particle size. In the present paper, quantitative relationships are established among the various mean dimensions on a polished cross section and the actual dimensions of the particles present. Particles of Uniform Size Spheres: If a metal sample contains particles of a phase a dispersed in the form of spheres of uniform size, a polished cross section through the sample will reveal circular areas of phase a with radii from 0 to ?, the radius of the spheres. Consider a cube of unit dimensions to be cut from the sample. If a cross section parallel to one of the cube faces is examined, the average number of particles per unit area (N,) equals the number of particles per unit volume (Nv) times the probability p1 that the plane would intersect a single sphere positioned at random within the unit cube. Since, of the various possible positions for the cross-sectional plane over the unit length from top to bottom of the cube, only those positions existing over the length 2r would lead to the plane intersecting the sphere, the probability of intersecting a single sphere is just 2r. N8= Nvp1 = Nd-2r [1] Applying the equality of area and volume fractions, the relationship is found between sphere size and average area s of uniform spheres intersected by a random cross section, 4 - f = NV V = Nr . — pra = N s = Nd . 2rs S = —pr2 [2] A similar analysis reveals the average traverse length across spheres of uniform size when random lines are passed through the sample. If a randomly oriented unit cube is cut from the sample and a randomly positioned line is passed through the cube parallel to a cube edge, the number of spheres intersected by the line (Nl) equals the number of spheres per unit volume times the probability p1 of the line hitting a single randomly placed sphere in the cube. Since possible positions of the line occupy unit area, and possible positions for which it will pass through the sphere occupy an area of pr2, the probability of the line hitting a randomly placed single sphere is pr2. NL = Nv p1 = Nvpr2 [3] Combining this relationship with the equality of volume and lineal fraction, the desired relationship is obtained between radius and mean lineal traverse length -i, for spheres of uniform size. 4 - - 3 l=4/3r [4] Circular Plates: Consider a sample containing particles of a phase a in the form of circular plates of uniform radius r and thickness t, where r >> t. If the plates are randomly oriented, as in a sufficiently large sample of a fine grained polycrystalline material, area and lineal analysis may be carried out with parallel cross-sectional planes and lineal traverses. If the plates are not randomly oriented, it is necessary to randomize the orientation of the cross-sectional planes and traverse directions. Let a unit cube be cut from the sample, and a cross-section plane be passed through the cube parallel to one of the cube faces. The number of plates cut by the cross-sectional plane per unit area is equal to the number of plates per unit volume times the probability of a plate intersecting a single randomly positioned and randomly oriented plate in the cube. If J is the component of the plate diameter in the direction normal to the cross-sectional planes, the probability of a plane cutting a single randomly oriented plate is equal to J, the mean value of J for all possible orientations of the plate. Let 4 be the dihedral angle between a plate and the cross-sectional plane, and let p?, d? be the probability that a plate makes an angle between 4 and ? + d? with the cross-sectional plane. Then for ran-

Jan 1, 1954

By J. W. Rutter, K. T. Aust

THE object of the experiments to be described in this report was to determine, first, which grains, out of a large number introduced into a sample in which their growth could proceed, were able to grow most successfully; and, second, the factors which control their growth selection. In an earlier study of grain boundary migration in high-purity lead,' it was found that, under some conditions, the most successful grain in an experiment of this type bears a special orientation relationship to the grain into which it is growing. The present work represents an extension of the previous study, directed at the determination of the orientation relationships which appear under a wider variety of conditions. Experiments of this general type have been done using commercial aluminum2 with somewhat conflicting results. In the present experiments, in contrast to the above,' the sample composition was a principal controlled variable, resulting in a considerable clarification of the phenomena observed. EXPERIMENTAL TECHNIQUE The experimental technique used in this investigation was essentially that employed previously in studies of grain boundary migration kinetics.1'3 The material used was zone-refined lead with various small amounts of tin or silver added to study the effect of varying the sample composition. The specimens were in the form of single crystals, about 1/4 in. 1/4 in cross section by 3 to 4 in. in length, grown from the melt in a horizontal graphite boat. A crystal grown in this way generally contained a lineage or "striation" substructure of the type shown in Fig. 1 of Ref. 1. This substructure consists of an array of low-angle boundaries which partition the crystal into regions misoriented from each other by a few degrees. The substructure constitutes a source of driving energy, estimated to be about 4000 ergs per cc, for the migration of a large-angle grain boundary into the striated crystal. New grains were introduced by plastic deformation in compression of a localized reglon at one end of the sample. Re-crystallization occurs at room temperature in the deformed region, introducing a large number of new, striation-free grains into the specimen. These grains are able to grow into the melt-grown crystal on annealing at a suitable temperature. The stria-tions are removed by passage of the grain boundary, as the substructure energy is utilized to produce the boundary migration. Usually, only one or two of the recrystallized grains persist after growth has occurred for about 1 cm out of the deformed region. Laue back-reflection X-ray photographs were obtained to determine the orientation relationship between the melt-grown crystal and the recrystallized grain or grains which grew most successfully in each specimen. EXPERIMENTAL OBSERVATIONS Fig. 1 shows the results obtained for a series of specimens to which had been added tin in the range from 0 to 5 ppm by weight. In this figure is plotted, in the standard stereographic triangle, the single axis about which the most successful recrystallized grain or grains are related to the starting, melt-grown crystal by the smallest rotation. The range of angular rotations observed about such axes is indicated beside each stereographic triangle. The results shown in the stereographic triangle on the left, Fig. l(a), were obtained by localized deformation at one end of each specimen at room temperature, followed by annealing in a furnace which had been preheated to 300°C. The furnace atmosphere was argon. It will be seen that the orientation relationships observed between the melt-grown and recrystallized grains are quite random. On the right, Fig. l(b), are shown results for samples in which the de-

Jan 1, 1961

By F. Selig, A. S. Odeh

A second-order approximation to the exact solution of the diffusivity equation corresponding to the pressure build-up of a well producing at a variable rate is derived. This approximation is applicable when the well's shut-in time is larger than the total time elapsed since the well was first produced. The resulting equations are compact in form and easy to use. Thus, the need for Horner's' theoretically precise but rather laborious solution to the above problem is eliminated. In addition, these equations apply where the use of Horner's widely known approximate method is questionable. From a practical point of view, the reported method is best suited for analysis of drill-stem tests and short production tests conducted on new wells. INTRODUCTION The utility of drill-stem and short production tests in reservoir studies has long been recognized by the reservoir engineer. If interpreted correctly they could lead to a wealth of information upon which may depend the success or failure of reservoirs' analyses. Initial reservoir pressure and the average flow capacity are two quantities that are normally sought from a drill-stem and/or a short production test analysis. Pressures are the most valuable and useful data in reservoir engineering. Directly or indirectly, they enter into all phases of reservoir engineering calculations. Therefore, their accurate determination is of utmost importance. The flow capacity kh of the reservoir is indicative of its commercial capability. In addition, it can indicate the presence of a darnaged zone around the wellbore and, thus, the necessity for remedial measures. Of the several methods used to analyze drill-stem and short production tests, Horner's' method is by and large the most common. It applies to an infinite reservoir and or a limited reservoir where the effect of production has not been felt by the boundary. Horner's method makes use of the so-called "point-source" solution of the diffusivity equation. The point-source solution is approximated by a logarithmic function and the superposition theorem is utilized to give the familiar pressure build-up equation where is the shut-in time, q is in reservoir barrels per day and the rest of the symbols conform with AIME nomenclature. Eq. 1 was derived for a well which produced at a constant rate q from time zero to time t and was then shut in. In actuality, such a constant rate of production does not normally obtain. Therefore, a correction must be applied to Eq. 1 to account for the varying rates of production. Horner suggested two methods. The first, which results in a theoretically accurate solution, is rather lengthy and laborious and, thus, it is not suited for routine analysis. The second which has been termed a "good working approximation" is the one used by the majority of the reservoir engineers. In the second method, Eq. 1 is modified by simply introducing a corrected time t, and writing where q is the last established production rate prior to shut-in, and t, is obtained by dividing the total cumulative production by the last established rate. Horner's original paper does not give any indication that this method of correction is based on any theoretical justification. In addition, there is a question as to what constitutes the last established rate. In case of a drill-stem test some engineers use the average rate obtained by dividing the total fluid produced by the total flow time, while others calculate the average rate by dividing the total fluid produced by the last flow-period time. Obviously, different results obtain for the different flow rates used. Because of this, a simple method to the varying-rate case was developed which is theoretically sound and which defines clearly the flow rate and its associated time to be used in the calculations. The final equation arrived at is where q* and t* are a modified rate and time, respectively, and can be easily calculated. In addition, it is shown theoretically that Horner's approximate method, if used for a variable-rate case, gives the correct pressure but would not be expected to give the correct flow capacity. MATHEMATICAL ANALYSIS The general equation governing the flow of slightly compressible fluid in porous media may be written as The elementary solution to Eq. 4, representing an instantaneous withdrawal of Q units volume of fluid at the origin at t = 0, is known as the instantaneous sink

By A. S. McLatchie, R. A. Hemstock, J. W. Young

Much attention has been given in the past few years to methods of increasing the recovery of oil from proven reserves. Numerous laboratories have made investigations to evaluate the possibilities of increased oil recovery by high-pressure injection of dry gas, injection of a propane slug followed by dry gas, solvent flooding. and by the injection at relatively low pressures of gases enriched with ethane and propane. Several years ago, Whorton and Kie-schnick' published the results of laboratory studies on high-pressure gas injection which showed that, in the case of light oils, recoveries could be considerably increased by sweeping the reservoir with dry gas at pressures in excess of 3,000 psig. The increase was attributed by those authors to the vaporization of oil at the invading gas front and viscosity and solubility effects produced at the front by the invading gas. Later, Stone and Crump' presented the results of a series of displacement experiments in which a light under-saturated crude oil was displaced from sand-packed columns with unusually high recoveries when the displacing gas was a rich condensate or a dry gas enriched with ethane or propane. They also conducted similar experiments at higher pressure on heavy undersa tu rated crude oil, although in this case the increase in recovery was not as great as in the case of the light oils. In both cases, viscosity reduction and swelling of the by-passed oil behind the invading gas front were believed to be responsible for the more favorable recovery of the original oil in place. Within the past year, other investigators", ' have presented the results of laboratory studies of miscible slug and solvent flooding recovery processes. This paper describes the laboratory methods developed for evaluating benefits to be obtained by enriched gas drive in specific reservoirs, and presents the results of several displacements of crude oils which possess a wide range of physical properties. The displacements were conducted at reservoir conditions of temperature and pressure. The apparatus used in the following experiments consisted of a sand-packed tube which served as the model reservoir, a cylinder of injection fluid, and a mercury pump. The stainless steel tube, 8 ft long and 0.53 in. I- was packed with a graded quartz sand. The high-pressure pump discharged mercury into the bottom of the injection fluid cylinder at a constant rate as low as 1 cc/hr. The average porosity and permeability of the sand column were 34.6 per cent and 3.25 darcies, respectively. In each case the tube was charged by the displacement of salt water by the reservoir oil under consideration. Recently a project was initiated to evaluate oil recovery by enriched gas drive from three oil reservoirs. Samples from a fourth reservoir (in this case high-viscosity oil) were studied with a view to obtaining recovery information of general applicability to low-grade, high-viscosity crudes. The oils from these four reservoirs exhibited a wide range of physical properties, and the reservoir conditions of pressure and temperature simulated in the laboratory represented several typical field conditions under which enriched gas drive might be employed. One of the reservoirs selected for laboratory displacement experiments produced an intermediate-gravity crude (29.6" API) by solution gas drive and a weak water drive. A low recovery in the range of 10 to 20 per cent was anticipated. Four displacement experiments were made to determine the effect of injection gas composition and initial gas saturation upon recovery of oil from the laboratory model. Two types of reservoir oil were used in these experiments. In the first run, a desaturated crude with a bubble point of 395 psi was charged to the tube. In the three subsequent runs, a simulated original reservoir oil was charged at 2,000 psi and produced by solution gas drive to 300 psi before beginning gas injec-

By Robert W. Hendricks, John B. Newkirk

A simple method is described for determining the orientation of a single crystal by means of a cylindr cal X-ray camera. Orientation setting to within ±1 deg is attainable by a stereographic analysis of a single cylindrical Laue pattern produced by the originally randomly mounted crystal. Final precision adjustments which permit orientation of the crystal to within ±5 min of arc from the desired position can be made by the method of Weisz and Cole. A chart, originally Presented by Schiebold and schneider7 and which allows a direct reading of the two stereographic polar coordinates of the corresponding pole of a given Laue spot, has been recomputed to aid in the stereographic interpretation of the cylindrical Laue X-ray photograph. Detailed instructions for the use of the chart, a simple example, and a comparison with the conventional flat-film Laue Methods, are presented. 1 HE problem of determining the orientation of the unit cell of a single crystal relative to a set of fixed external reference coordinates is fundamental to most problems of X-ray crystallography and to many experimental studies of the structure-sensitive physical properties of crystalline materials. Several techniques for measuring these orientation relations have been developed which correlate optically observable, orientation-dependent physical properties to the unit cell. Examples of such procedures include the observation of cleavage faces or birefringence, as discussed by bunn,1 or the examination of preferentially formed etch-pits, as discussed by barrett.2 Each of these methods is limited, for various reasons, to an orientation accuracy of approximately ±1 deg—a serious limitation in some experimental studies. Several other limitations decrease the generality of these methods. Of these, perhaps most notable is the absence in many crystals of the physical property necessary for the orientation technique. The most widely used methods for determining crystal orientation are variations of the Laue X-ray diffraction method. Because of the indeterminacy of the X-ray wavelength diffracted to a given spot, the interpretation of Laue photographs is now limited almost exclusively to the procedure of using a chart to determine the angular coordinates of the corresponding pole for each spot. For the flat-film geometries, either a leonhardt3 or a Dunn-Martin4 chart is used in interpreting transmission patterns, whereas a greninger5 chart is used for interpreting back-reflection patterns. A less common method of interpreting flat-film transmission Laue photographs is by comparing the Laue pattern with the Majima and Togino standards,6 or with the revised standards prepared by Dunn and Martin.4 Although this last method is applicable only to crystals with cubic symmetry, it can be very rapid and just as accurate as the graphical methods. The primary limitation of all the X-ray methods mentioned is the relatively small number of Laue spots and zones which are recorded on the flat film. Often, few, if any, major poles appear, thus making interpretation tedious and sometimes uncertain. The use of a cylindrical film eliminates this problem. Schiebold and schneider7 prepared a chart by which the orientation of the specimen crystal could be determined from a cylindrical Laue photograph. However, it was only drawn in 5-deg intervals of each of the two angular variables used to identify the Laue spots, thus limiting the accuracy of orientation to about ±3 deg. An examination of this chart indicated that if it were drawn in 2-deg intervals, crystal orientations to ±1 deg would be attainable. Subsequent use of the replotted chart has confirmed this accuracy. It is the purpose of this paper to describe the redevelopment and use of this chart, and to point out its advantages and limitations. I) CAMERA GEOMETRY AND CHART CALCULATIONS The geometry of the cylindrical camera with a related reference sphere is shown in Fig. 1. The X-ray beam BB&apos; pierces the film at the back-reflection hole B, strikes the crystal at 0, and the transmitted beam leaves the camera at the transmission hole T. One of the diffracted X-rays intersects the film at a Laue spot L. The normal OP to the diffracting plane bisects the angle BOL between the incident and diffracted X-ray beams. The point P on the reference sphere can be located uniquely by the two orthogonal motions 6 and 8 on the two great circles ENWS and BPQT respectively. Because the Bragg angle 8 (= 90 - < BOP) is always less than 90 deg, P always remains in the hemisphere BENWS. Therefore, if every possible pole P is to be recorded on the same stereographic projection, it is necessary that the projection reference point be at T with the projection plane tangent to the sphere at B.* The great

Jan 1, 1963

By J. H. Swisher, E. O. Fuchs

Rate equations were derived to describe the kinetics of internal oxidation of cylinders and spheres. The derived equations for cylinders were checked experimentally by means of sub scale thickness and electrical conductivity measurements on Cu-Cr alloy wires. The properties of the internally oxidized samples were examined with conductivity applications in mind. It was possible to produce uniform dispersions of Cr2O3 in copper with an initial chromium content as high as 3 wt pct. While electrical conductivities only a few pct less than that of OFHC copper were obtained, the Cr2Os particle size and spacing were too large for effective dispersion hardening. T.HE process of internal oxidation has been used widely in basic studies of the permeability of gases in metals. In a review article, Rapp1 has discussed the principles of internal oxidation in considerable detail. From a technological standpoint, internal oxidation is often considered undesirable, since it is a means by which inclusions can be introduced into an otherwise clean material. Another important aspect of internal oxidation is its use as a means of dispersion hardening a material. Broutman and Krock2 discuss this and other methods for making dispersion hardened alloys. The only internally oxidized material known to the authors which is commercially available is a Cu-BeO alloy.3&apos;4 This alloy is made from Cu-Be alloy powder, using a so-called Rhines pack. It has a tensile strength of 80,000 psi and retains its strength at relatively high temperatures. The objectives of the present study were to derive rate equations for the internal oxidation of cylinders and spheres, to check the derived equations for cylinders experimentally, and to examine the structure and properties of internally oxidized Cu-Cr alloys. The Cu-Cr system was chosen for this study because uniform dispersions are obtainable at high alloy contents, which is a desirable characteristic in dispersion hardened materials. RATE EQUATIONS FOR VARIOUS GEOMETRIES A number of authors5--9 have derived equations to describe internal oxidation kinetics. These derivations differ somewhat in mathematical assumptions and approximations, and all except one of the derivations deal exclusively with the internal oxidation of plates. The exception is a brief treatment of cylindrical and spherical geometries given by Meijering and Druy-vesteyn9 as a part of a comprehensive paper on the general subject of internal oxidation. These authors did not obtain rate data to check their derivations, although they did show that the hardness profile across an internally oxidized sample is directly related to the rate of interface movement. For cylindrical and spherical geometries, a quasi-steady-state approximation is needed to circumvent mathematical complications in obtaining a solution to the basic differential equations. In using this approximation, we consider the concentration gradient of dissolved oxygen in the internally oxidized zone or sub-scale to be the same as the gradient which would be present if there were no movement of the subscale interface. The steady-state approximation introduces an error of about 1 pct in computing the rate of internal oxidation of an Fe-1.0 pct Mn alloy plate, if the present method is compared to the more exact method of Wagner.7&apos;10 The details of the derivations of the rate equations for cylinders and spheres are given in the Appendix, and only the results of these derivations are given below. The final equations obtained by Meijering and Druyvesteyn9 can be shown to be equivalent to our Eqs. [1] and [2], although the two approaches are somewhat different. Cylindrical Geometry. [2] where r1 is the outer radius of the cylinder or sphere, cm, r2 is the radius of the unreacted core, cm, see Fig. l(a), D is the diffusion coefficient of oxygen in copper, cm2 per sec, %O is the concentration of dissolved oxygen at the surface of the specimen, wt pct, %Cr is the initial chromium concentration in the alloy, wt pct, and t is the reaction time, sec. Plate Geometry. The analogous rate equation for a plate has been derived previously for internal oxidation of Fe-Al alloys.8&apos;11 For Cu-Cr alloys, we may write the same equation as follows: [3] where r1 is the half-thickness of the plate, cm, and r2 is the distance from the mid-plane to the subscale intherate is An analysis of Eqs. [1], [2], and [3] shows that for a plate the rate is completely parabolic. The initial

Jan 1, 1970

By E. W. Felegy

THE need for improved mine communication to increase efficiency and to insure greater safety has long been recognized. General and unrestricted communication between all points underground, and between the surface and all points underground, is probably the least advanced phase of the mining industry. An ideal system of mine communication must require no fixed wire installations. The equipment must be small, lightweight, and readily portable, and the power requirements low. A system that can be used not only under normal circumstances but also in an emergency, when the continuity of wires, tracks, and pipelines may be disrupted, must function independently of any aid furnished by standard installations. Radio communication offers possibilities of meeting all the requirements necessary for an ideal communication system in underground mines. Transmission of signals must be achieved through one or both of two mediums, through the air in mine openings or through the strata. The results or lack of results obtained by early investigators showed conclusively that radio communication by space transmission cannot be accomplished effectively beyond line-of-sight distances in underground passageways. A radio system underground therefore must depend solely upon transmission through soil and strata. The application of radio to underground mine communication was investigated by many individuals and agencies at different times in the last several decades, but little success was achieved before World war 11.2-0, The results of experiments during the war, and further knowledge gained in experiments with vastly improved communication methods and equipment after the war provided the background for additional research in radio communication in underground mines. During 1950 to 1.952 the University of Minnesota sponsored an investigation to determine the possibility of developing: a system of radio communication universally applicable in underground metal mines in the Lake Superior district. The possibility of using radio equipment to determine the imminence of rock bursts in deep copper mines in that district also was investigated. The investigation supplemented previous and concurrent emergency mine communication studies of the U. S. Bureau of Mines. Testing equipment and laboratory facilities maintained by the Bureau of Mines at Duluth, Minnesota, were used in the research program, which was conducted as a mining engineering graduate research problem by the present writer under the direction of T. L. Joseph and E. P. Pfleider. The radio units used in the research program were designed and built to specification solely to conduct tests of radio communication in mines. Two identical units were used in all tests. Each unit contained a transmitter section, a receiver section, and a power-supply section, mounted on a single chassis. The entire unit was enclosed in a single 10x12x18-in. metal case provided with a leather-strap handle for carrying purposes. The front of the case was hinged to open upward and provide easy access to the single control panel on which all controls were mounted. Storage batteries supplied the operating power for all tests. Standard 6-v automobile batteries were utilized to provide adequate capacity to conduct tests for a full day without exhausting the battery. A frequency range from 30 to 200 kc was covered in eight pre-fixed steps on each unit. The carrier frequencies were crystal-controlled and amplitude-modulated. The receiver employed an essentially standard superheterodyne circuit and was sufficiently sensitive to detect signal strengths of 5 micro v. A heterodyne circuit was employed in the transmitter to obtain the low-carrier frequencies used in the units. Power output of the transmitter, usually less than 2 w, rarely exceeded 3 w in any test. Tests were conducted in mines on the Vermillion iron range in Minnesota, the Gogebic iron range in Wisconsin, the Menominee and Marquette iron ranges in Michigan, and a copper mine in the upper Michigan peninsula. All tests were conducted when the mines were operating normally, and usual mining, maintenance, and transportation activities were in progress, so that any interference caused by normal production activities could be evaluated during the tests. Tests were made between different points underground in each mine, and between underground and surface points at some mines. Test readings obtained at any one mine were calibrated in the laboratory before another series of tests were begun at the next mine. The transmitter and receiver were separated by one or more levels in each test, and generally there was no other means of communication between test points. Two 100-ft lengths of rubber-covered wire were used for antenna wires on each unit in both transmission and reception. The ends of the wires were connected to ground points in one of several methods, depending upon physical conditions at each test site. The wires were clipped to metal rods about 200 ft apart in the back, side, or bottom of the mine opening where the character of the rock permitted driving rods. Both wires were clipped to points about

Jan 1, 1954

By AIME AIME

PRIZES totaling $450 were awarded at the Annual Meeting luncheon on Monday, Feb. 9, to the winners of the third national student prize paper contest. The undergraduate prizewinners, each of whom received a check for $100, were as follows: Mayo W. Lanning, Lafayette College, for his paper entitled ?Some Aspects of the Mining Methods Employed at the Scrub Oak Mines of the Alan Wood Steel Company,? (entered by the Lehigh Valley Section). Charles F. Parent, Montana School of Mines, for his paper entitled ?Relationships of Manganese Minerals in the Butte District,? (entered by the Montana Section). Harry Czyzewski, University of Illinois, for his paper entitled ?A Metallurgical Study of Cast Irons Used for Glass Molds,? (entered by the Chicago Section).

Jan 1, 1942