Search Documents

By A. M. Gaudin

TEN years ago Taggart, Taylor and Ince1 described a workable, convenient apparatus for the measurement of contact angles be-tween cleaved, ground or polished particles and captive bubbles. Wark and Cox2 and Wark and Sutherland3 have done an im-mense amount of experimental work with this apparatus. Their work has had as principal object the determination of "con-tact curves." Contact curves are Cartesian charts in which pH (or some other variable) is plot-ted against quantity of modifying agent. The rectangular area is broken into two or more curvilinear areas separated by the contact curve. The curve indicates that a sharp demarcation exists between condi-tions that bring about sticking of particles to bubbles and conditions that do not pro-duce sticking, The type curve appears in the TRANSACTIONS as Fig. 1, page 248, volume 112. Wark and Cox offer data to show that the contact angle has a value determined by and characteristic of the agent used. Wark and Cox also make the statement that they believe this value is independent of concen-tration (ref. 2a, p. 209), They say: It is suspected that, given sufficient time and provided that there are no disturbing factors. the full ethyl xanthate angle (corresponding to a complete xanthate film) would be obtained in every case where contact occurs.

Jan 1, 1940

By F. H. Buchella

When Duval Sulphur & Potash Co. awarded pre- mining stripping and early mining at Esperanza to an independent contractor, it was agreed that monthly payments for excavation were to be made on a truck count. At six-month intervals, however, adjustments must be made on the basis of actual excavation or cut from the pit area. It was estimated that it would be three times more expensive to have the pit sectioned by chain and transit survey than to use photogrammetry, since it would take two crews of three men approximately two weeks to do the field work, another two weeks to plot the sections, and additional time to establish a control network. Therefore it was agreed to have the mine area mapped by photogrammetry for both the premined surface and for semi-annual check surveys necessary for intermediate settlements. A triangulation net was established with a maximum distance of 900 ft between control points. In about 30 working days a two-man survey crew, using a theodolite, set up and triangulated 30 stations and calculated their results. For ease in spotting on the photographs, control stations were marked on the ground with white-painted tires centered over the survey pins.

Jan 6, 1960

By F. D. DeVaney

IT is of great interest that the various organizations engaged in the search for a cheap and efficient agglomeration process for fine magnetite concentrates-essential if the taconites are to be utilized-have ended up with processes that are basically different. This paper describes the development and the present status of the shaft-type furnace as now utilized by the Erie Mining Co., which is managed by Pickands Mather & Co. The shaft furnace has always had an appeal to metallurgists because of the simplicity of the design and the possible low fuel consumption. Work done on pelletizing at the University of Minnesota Mines Experiment Station by E. W. Davis and his associates determined that it was possible to roll up fine magnetite concentrates in a balling drum, and that, if such balls were fired at a sufficiently high temperature, a hard, indurated pellet, well adapted for use in a blast furnace, could be made. Early furnaces had no heat recuperation and the heat consumption was in the order of 2 million BTU's per long ton.

Jan 3, 1958

By F. E. Bachman

There is such a great variety of opinion concerning the best method of determining phosphorus in pig iron and steel, that a list of determinations, on a uniform sample of pig iron, together with a short description of the methods used by different chemists, and a few experiments on the accuracy of some of the methods used, [nay be of interest to members of the Institute. All the results given in List A are from the same lot of drillings, thoroughly mixed, except Nos. 8 and 9, and 28 to 32 inclusive, which are from the same pig, but were taken at a later period.

Jan 1, 1882

By A. Kenneth Schellinger

IF the ball mill is considered only from an energy standpoint, it can be thought of as a converter of kinetic energy into heat energy and surface energy. The law of the conservation of energy must apply to the ball mill as it does to any machine or process in nature. The heat energy output of the ball mill is apparent to any casual observer of the operating mill since the outflow pulp will be appreciably warmer than the inflow water and rock. The rock in the ball mill is crushed by shearing of its ionic bonding caused by some impact-induced stresses beyond the elastic limit. As the bonds holding the mineral crystal lattices together are ruptured, new surface area is created on each unit of which a definite number of unsaturated bonds exist. Such unsaturated energy of bonding may be termed the "surface energy," and is a potential energy figure. This created energy was withdrawn from the ball mill system and represents an absorption, or disappearance of heat. To reduce the size of the rock, surface area must be created and with it the at-

Jan 6, 1951

By H. Bernstein

WHILE the beryllium -copper (2 pct Be) alloy is nominally nonmagnetic, the presence of iron impurity causes variations in the magnetic proper- ties which, at times, attain excessive proportions. This investigation was carried out to establish the effect of small amounts of iron on the susceptibility of the material and to determine if the effect could be minimized. Beryllium-copper is an age-hardening alloy which

Jan 1, 1959

By Kalanadh V. S. Sastry, D. W. Fuerstenau

A locked-cycle balling procedure has been designed to simulate continuous, closed- circuit balling drum operation in the laboratory. By this method, it is possible to simulate the surging in green-ball production rate and circulating load that is experienced in industrial balling circuits. Through an investigation of the effect of feed rate on the stability of the locked-cycle, balling process, it was found that higher feed rates lead to increasing instability in the process. An analysis of the experimental ,results is presented and the utility of the locked-cycle experimental technique for evaluating the stability of an industrial balling drum operation is discussed.

Jan 1, 1976

By H. H. Wade, N. F. Schulz

The large quantities of iron-bearing materials, including taconite, semi-taconite," and other low-grade ferruginous materials occurring in Minnesota and elsewhere, constitute an important potential source of iron. Satisfactory grade and recovery of iron ore concentrate cannot ordinarily be obtained from these ferruginous materials by simple methods of beneficiation. Iron is distinctive in that the free metal and two of its oxides [magnetite (Fe,O,) and maghemite (gamma-Fe,O,) ] are strongly ferromagnetic. The successful magnetic separation of natural magnetite from taconite has already been established on a commercial scale. The iron in semi-taconite, how- ever, occurs largely as goethite (Fe,Os.H,O) and hematite (Fe90,) which do not respond to ordinary magnetic separation methods. Magnetic roasting converts these iron oxides to magnetite, which can, after liberation, be magnetically concentrated.

Jan 11, 1960

By Bruce A. Lamberton

In U. S. underground mines concrete work is not widely used. Timber and steel are cheaper, and there are few serious water problems. But in the Union of south Africa men dig deeper, more persistently, and probably more profitably than anywhere else on earth. Some gold mines near Johannesburg are below the 10,000 level and employ as many as 35,000 natives on a single property. Underground substations, pump chambers, and air conditioning plants have capacity to serve small cities. The complexity and extent of underground operations and the heavy subsurface water flows, especially in the new Free State gold fields, require heavy in a Deep concrete installations.

Oct 1, 1956

By Jerrold Marcus

The peninsula is roughly 700 miles long and 180 miles wide. The southern portion is the American-sponsored Republic of Korea and the northern half is the Soviet-promulgated People's Democratic Republic of Korea. The area of South Korea is almost 40,000 sq miles, about the size of the state of Maine, and contains a population estimated at 22.5 million. Prior to annexation by Japan in 1910, the Korean economy was based on a system of self-sufficient farming units, but with Japanese occupation it was geared to Japanese economy. Emphasis was placed on supplying raw materials for Japanese industry and food surpluses to help feed Japan, and on providing a connecting link with Manchuria, traditionally a major raw material source for Japan. Small metal refineries, ore processing, and semi-finished goods manufacturing units grew into existence in the northern part of Korea, where much of the electric power is generated. Under Japanese domination, the south remained essentially agricultural. Food productivity was increased, although manufacture of elementary consumer goods was stimulated for Japanese markets.

Apr 1, 1956

By Philip L. Collyer

A technique for evaluating the similarity of ore deposits is presented. A Q-mode cluster analysis is performed using information on tungsten mines in North America. This is a method of grouping several samples according to their similarity based on a simple matching coefficient. Tungsten mines are grouped or clustered on the basis of geologic variables. It is possible to interpret and evaluate different ore environments according to age, mineralogy, and other variables. It is well known that variable geologic conditions influence the occurrence of certain types of minerals. If one variable is responsible and identified, that variable can be searched for in exploration. If several interrelated variables are responsible for forming a favorable environment, then recognition and identification may be more difficult or completely masked. Therefore it is helpful in exporation to isolate and identify multiple interrelated variables which control the localization of mineral deposits. Cluster analysis is useful in mineral exploration where considerable amounts of data are available for analysis. Subtle relationships that might be overlooked because the data are voluminous can be isolated using this technique. Cluster analysis can be used to establish exploration prioriy in unknown areas on the basis of similarities to known metallogenetic provinces.

Jan 1, 1976

By L. W. Eastwood

THE structure of eutectics has been studied by a number of investi-gators, and the complexity of the structural relationship of the compo-nents has been agreed upon, especially that of the "eutectic colony," type III of Portevin's1 classification. This paper does not attempt to alter the present classifications of eutectics; rather, it discusses the relationship between the macrostructure and the microstructure of the copper-cuprous oxide eutectic, and describes in detail the mechanism of the formation and the structure of the eutectic. Further, throughout the entire discussion it attempts to point out certain misconceptions in regard to the interpretation of the observed structure of the copper-cuprous oxide eutectic, one of the so-called "eutectic colony" types, and to correlate as much as possible the work done by the writer with that done by other investigators. Of the three types of eutectics listed by Portevin,2 the eutectic colony type has presented the greatest difficulty in interpretation. Although the copper-cuprous oxide eutectic is typical of the eutectic colony type in appearance, it may not be truly representative because the copper forms about 96 percent of the eutectic and the cuprous oxide about 4 per cent. The interpretation of the origin and structure of the "eutectic colony" given here is strictly limited, therefore, to the copper-cuprous oxide eutectic.

Jan 1, 1933

By Horace C. Knerr

It has been shown that the resistance to corrosion of duralumin sheet is greatly influenced by the quenching medium used in heat treatment, or, more specifically, by the rate of cooling during quenching. The severity of corrosive attack after exposure to salt-water spray increases in .the following order: The tensile strength, yield point and elongation are only slightly affected by the quenching medium, as shown in Table 1. Tensile test requirements: yield stress, 25,000 lb. per sq. in. minimum; ultimate stress, 55,000 lb. per sq. in. minimum; elongation in 2 in., 18 per cent. minimum.

Jan 1, 1931

By Grant Buma

The purpose of this paper is to present arguments and evidence that there are natural processes at work which tend to minimize the impact of solution mining on the environment. The contaminants have two sources. First are elements which were present in the roll-front deposit in insoluble compounds, for example, uranium in uraninite and coffinite, molybdenum, arsenic, iron, cobalt, nickel, etc. in sulfide minerals, vanadium in micas and clays, etc. Second are elements introduced by the leach liquor. Precipitation of reduced compounds, scavenging of heavy elements and absorption by quartz and clays, can all reduce the amount of heavy elements in solution. If a roll can be demonstrated to be actively precipitating uranium and heavy metal elements, then the presence of precipitants (pyrite and carbon) can be assumed. Criteria for recognizing an active roll are described.

Jan 1, 1979

By G. Adel, J. Richard Lucas, C. Haycocks

This paper describes over sixteen computer programs developed at Virginia Polytechnic Institute and State University during the past twenty years to assist in the design of coal operations. Overall development concepts in the construction of the programs are outlined, commencing with those used in the exploration phase of mining and extending through economic analysis and into the design of specific engineering systems such as belt, rail and power networks, scheduling, rock mechanics problems and simulation of face systems. Summarized information is given for the use of the major programs including user restrictions, input data, typical output and industrial applications and case studies. Analysis has been made of the programs' applications by industry throughout the world. Such analysis is facilitating development of new programs as well as a refinement of existing ones. To date programs have been constructed in four categories: exploration, ground control, economic and simulation. Face production simulations are stochastic in nature and require the use of time study data obtained at sites underground. Future programming efforts currently under development are aimed at interactive programs for use with minicomputers and, where advantageous, with graphical displays.

Jan 1, 1983

By R. J. Robbins, D. L. Anderson

A tunnel boring machine has potential use in al- most any type of mining where the access shaft (or adit) is large enough or can be made large enough for its initial entry and where the orebody is of sufficient size to warrant its use. Some time will inevitably be lost in negotiating curves or making lateral moves and moving from level to level. Nevertheless, if the orebody is sufficiently large, advance scheduling can minimize the lost time encountered in such moves. Ideally, a mine will be planned for the use of these machines, thus eliminating access and transport problems. From the viewpoint of time involved, the rate of advance by boring as compared to conventional means is worthy of review. For instance, the Blanco Tunnel, one section of the Bureau of Reclamation's San Juan-Chama Project in southern Colorado, was bored in competent sedimentary rock with the following performance:

Jan 7, 1967

By Rossiter W. Raymond

I desire to call the attention of the Institute to an interesting experiment, which may turn out to be an indication of a valuable improvement in the manufacture of steel. As the members are aware, the addition of ordinary spiegeleisen, in the open hearth or Bessemer converter, to a bath of decarbonized iron, has a twofold object,—the recarbonization of the bath to a desired degree, and the remedy of the red shortness otherwise found to be inevitable in the final product. This red shortness is ascribed to the presence of oxide of iron in the molten metal; and it is supposed that the manganese of the spiegeleisen, uniting with the oxygen of such oxide, carries it into the slag. At the same time there is a small percentage of the manganese usually left in the cast steel, probably to the improvement of its quality. Whatever be the true explanation the effect of the manganese is acknowledged to be not only beneficial, but necessary. But the use of spiegeleisen containing high percentages of carbon limits the quantity that can be introduced, because the carbon must be limited if soft steel is desired. This inconvenience becomes so serious as to prevent the use of ordinary spiegeleisen in the manufacture of steel containing more than, say two-tenths per cent. of phosphorus; since the quality of the steel can be made tolerable only by reducing its contents of carbon in proportion as the

By W. M. Tuddenham, R. J. P. Lyon

In many areas surrounding the orebodies in mining districts rocks have been bleached and altered by the ore-forming solutions and have been oxidized during later weathering processes. A number of the rock-forming silic-ates have been broken down to clay, sericitic micas and chlorites have been developed, and pyrite may be found hundreds of feet outside the economic limits of the orebody. These halos of altered ground are prime targets used by geologists in many districts to delineate promising sites for drilling. Both in the field and in the laboratory it is often difficult to map these mineralogical changes in the halos in detail without numerous petrologic examinations. The secondary minerals are generally fine-grained, and since conversion of one mineral to another is often progressive, many alteration processes have not proceeded to completion (feldspars to clay to sericite mica). Qualitative detection of these minerals is difficult; quantitative determination is frequently impossible.

Jan 1, 1960

By Clarence O. Babcock

A simple robust rock bolt load gage was tested in the laboratory to define its characteristic behavior and to obtain a measure of its performance. The gage uses three vibrating wire sensors crimped 120 (2.09 rad) apart into the outer surface of a hollow cylindrical steel, tube. The resonant frequencies of the wires change as the gage is loaded. This change is read with a Creare meter developed for the Bureau of Mines on a previous contract to read borehole stress gage results. A statistical analysis of data obtained defines the variables influencing results. A U.S. patent (3,914,992) assigned by the author to the Dept. of the Interior was granted Oct. 28, 1975.

Jan 1, 1978

By G. Kinder, R. Gilges, W. Stoker, R. Davey

The Bingham Canyon Mine, located 48 km (30 mi) southwest of Salt Lake City, Utah, is operated by Kennecott Copper Corporation's Utah Copper Division. This operation is the world's largest open-pit copper mine and produces 96 000 tons (106,000 st) ore and 327 000 tons (360,000 st) waste each day. This material is loaded by large electric shovels and transported by both truck and rail haulage. To meet the requirements of the Clean Air Act of 1970 (as amended), new facilities for the control of smelter emissions were required and are now nearing the final stages of construction. The facility will be capable of treating all the output from the mine, some 2,530 tons (2,789 st) per day of combined concentrate and precipitate. Costing $280 million and necessitating the replacement of reverberatory furnaces with continuous smelting vessels, the plant, with its massive and complex gas handling and acid-making facility, is required to remain on-stream with the minimum of pollution control equipment outages to conform with Federal Regulation 52.2325.

Jan 8, 1978