Search Documents

By C. N. Stout

Square-sets go out and labor saving combination of top-slicing and sub-level caving raises tons per man hour 300 pct, cuts timber cost 50 pct to permit mining lower grade ores.

Jan 1, 1953

By Adrian C. Dorenfeld

Factorial design is a mathematical method of drawing valid conclusions from a series of tests made in a predetermined pattern. It is applied to flotation ore testing using, in this case, five variables, each varied twice, requiring a total of 32 tests. Representative conclusions are checked by repeat testing.

Jan 12, 1951

By R. J. Blackwell

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus became citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil.

Jan 6, 1950

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By John D. Sullivan, Chester R. Austin, Edwin J. Rogers

The problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce lightweight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough qo that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an - outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, partitularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating."² The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the Purpose Of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By H. H. Kaveler

Education is for the purpose of developing citizenship, and, if it is pursued for the additional purpose of preparing for a professional career, such as engineering, it is also directed to developing a knowledge of essential science, aptitude for the application of science to practical situations, and a knowledge of the industrial art in which the engineer will be engaged. The process of education required for engineering must of necessity extend beyond the classroom into industry. For that reason, the education of engineers should be divided as between the university and industry. Specialization in engineering should logically come as a result of experience in an industry. The student cannot take the time in a university, and, the university cannot teach the skills required to develop a specialist without sacrifice to the more essential broad purposes of formal education. In addition to talent in science, aptitude in the application of scientific fact, and knowledge of the industrial art, the engineer should possess certain personal qualities which are helpful in the pursuit of a professional career. Those personal qualities are: the ability to work as a partner in an enterprise, the ability to do jobs in a way whereby job performance is a means of gaining experience and increased responsibility, the capacity to write and speak in an understandable manner, and, a Proper regard for the "significance of answers." These pcrsOnal qualities may be of almost equal importance to acabemic accomplishments in the field of science. Development of such personal qualities are an essential part of the student's training in the university and in industry. They can be developed effectively through the leadership of instructors. Compulsory Education Nature played a mean trick On the human race when the evolutionary Process failed to develop in the individual a capacity to inherit knowledge. Were knowledge transmissible in a cumulative manner from generation to generation, mankind would be by inheritance wise beyond measure within a few generations. Then there would be little if any need for a "system of education." As matters stand, however, all must suffer the burden of starting life at the "zero " level of learning from which station each rises depending upon individual capacity to assimilate knowledge left of record by our predecessors and the individual effort exerted to compensate for Nature's failure to endow the offspring with intelligence. In the United States some degree of education is generally regarded as essential and necessary. Therefore, all citizens are subjected by law to an educational process covering the primary school age from six to sixteen years. Beyond the schooling required by law, many attend secondary schools, and beyond that, schools of higher learning. Our standard of living is at a level that permits an increasingly large fraction of the population the opportunity to go through all of the formal educational process. As a result, education in the colleges and universities has almost reached a mass production level. In spite of the high

Jan 1, 1949

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

The problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce lightweight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough qo that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an - outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, partitularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating."² The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the Purpose Of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By Kalanadh V. S. Sastry, D. W. Fuerstenau

Design and operation of a batch balling drum that can be used easily for experimental investigation of the balling or granulation behavior of particulate materials are described briefly. An experimental procedure for ascertaining the growth kinetics of iron ore concentrates or other particulate materials with this kind of apparatus is outlined.

Jan 1, 1972

By E. B. Thornhill

In this paper on the recovery of mercury as sulphide, from the residues from the amalgamation and cyanide treatment of high-grade ores and concentrates, I will not discuss the many reactions, chemical and other- wise, that take place in the general process, but confine myself more particularly to the methods of recovering the mercury. I submit charts of two amalgamation-barrel charges, Figs. 1 and 2, which are self-explanatory. The flow sheet of the high-grade and the mercury extraction plants is showh in Fig. 3.

Jan 1, 1916

By O. Hyvärinen

The treatment of anode slimes at Outokumpu Pori Copper Refinery comprises the following process stages: copper leaching by air oxidation, nickel removal by digesting slimes in concentrated sulphuric acid at 200 °C, and dissolving of the formed nickel sulphate into water, roasting of the slimes in controlled gas atmosphere at 600 °C for selenium removal, smelting of slimes in a Doré furnace, electrolytic refining of silver, sulphuric acid and aqua regia leaching of slimes from the silver cells followed by the reduction of gold and platinum metals. The paper discusses operational experiences and recent developments of the process.

Jan 1, 1984

By William N. Page

HAVING recently made a careful professional examination of this tract, I think its peculiar geographical, topographical and geological relations may prove interesting to members, not only because they are somewhat unusual in such a combination, but also as presenting the economical conditions of a region not widely known, at the western base of the Alleghanies.

Jan 1, 1889

By W. Fletcher, R. C. Schenk

This paper outlines a well proven and highly successful approach for eliminating many of the problem and frustrations often experienced in plant startup. The approach was developed over a period of 25 years during which some 90 plants were commissioned. This paper discusses startup from the contractor’s perspective and highlights the requirement for detailed startup planning, careful coordination during the project final construction phase, and thorough checkout of equipment prior to introduction of feed. Performance of these services has demonstrated a valuable opportunity exists for the contractor to assist in the training of the plant operating personnel.

Jan 1, 1983

By G. M. Roberts

During the six years that the writer was connected, as chemist and chief assayer, with the Proprietary Mines, Broken Hill, N. S. W., several interesting experiments were made in the sampling of the silver-lead bullion obtained from the waterjacket smelting-furnace.

Jan 1, 1899

By R. McNeill, D. E. Weiss, E. A. Swinton

In a continuous countercurrent exchange process, an alteration in any one of the operating conditions has a complex effect on the others, which can only be predicted by employing the transfer unit or the theoretical stage theory on a basis of trial and error. A simple method is described for illustrating diagrammatically the behavior of a counter-current system, the equations being simplified by means of a concept the maximum hypothetical exchange performance. An example based on a typical metallurgical system is given, in which a divalent metal is recovered from a dilute solution, the resin being regenerated continuously by a monovalent ion. Useful conclusions are drawn from a study of the theory. Practical methods for performing continuous ion exchange are discussed, and the development of equipment based on modified ore dressing jigs is described. A swinging sieve jig contactor is evaluated experimentally. DURING the last decade, the new synthetic ion exchange resins have been applied extensively in industries outside the field of water treatment, but there is no record of a continuous counter-current process operating on an industrial scale. Attempts have been made to devise a satisfactory process but many problems remain to be solved. The basic principles of continuous processes will be outlined, as well as the major problems in their operation and the progress made in the CSIRO laboratories toward the development of satisfactory industrial techniques. In the metallurgical field ion exchange resins can be used for various applications such as the recovery and concentration of valuable metals from mine waters,' the regeneration of pickling and plating liquors," the prevention of pollution by waste effluents and the recovery of the constituents from them," and the purification of valuable metals such as the rare earths by chromatographic fractionation on columns of ion exchange resins.7,8 . Turther applications undoubtedly will be found in the field of hydrometallurgy where the use of ion exchange resins would enable direct extraction of the desired metal ion from the filtered leach liquor or the leach pulp. For example, an ion exchange process has been described recently for the extraction of gold from a cyanide leach pulp." A continuous process would have advantages in many applications over the usual process employing a fixed bed and intermittent cycle. In a recovery process, it would yield a product stream of steady purity and concentration, it would waste less water in rinsing, and if the contacting apparatus were efficient less resin would be used, since each portion of the resin would be cycled as soon as it was loaded instead of lying idle until the whole bed was ready for regeneration. A very major advantage is that it would be simpler to control automatically. It is probable that continuous operation will be the key for really large scale applications of ion exchange. The flow sheet of a continuous ion exchange recovery-concentration process is illustrated diagrammatically in Fig. 1. Dilute liquor containing the valuable ion flows through the stripping section countercurrently to a moving bed of resin and leaves after a final contact with freshly regenerated resin. The resin leaves the unit almost in equilibrium with the incoming liquor and then flows to the regenerating unit where it is treated by a slow countercurrent flow of concentrated regenerant solution. The adsorbed ion is displaced from the resin and appears in the concentrated product stream. The resin then must pass through a rinse unit or section where regenerant entrained by the resin is washed back into the regeneration section by water. The regenerated and washed resin is then recycled back to the stripping section. I. Theoretical Operating Behavior of Continuous Ion Exchange Stripping System The simple theory of continuous ion exchange is analogous to that of solvent extraction and other diffusional transfer operations and is governed by the equilibrium relationship, the mass balance, the rates of mass transfer, and the contacting efficiency of the unit. Equilibrium Relationship—The relative affinity of two ions A and B, for a particular resin immersed in their solution, can be expressed by plotting compositions of the solution against compositions which exist in resin in equilibrium with those solutions, i.e. C/Co vs q/a where C, is the total normality of the solution, C is the normality of ion A in the solution, a is the total exchange capacity of the resin in gram equivalents

Jan 1, 1956

By Andrew B. Crichton

No more important question has come before the coal industry in the past decade than the prevention of stream pollution by mine drainage; especially in Pennsylvania, where large areas of coal land have been developed. It may be thought that the problem of labor or lack of transportation outweighs in importance that of stream pollution. We can see possible remedies for labor and transportation problems but there is no known satisfactory solution of the mine-drainage problem. The subject has been given little serious attention, for, until recently, it has been little understood; but in the past year it was brought to the attention of the coal-mining industry by the introduction, in Congress, of several bills designed to prevent the discharge of acid waters from mines or other sources into navigable streams, or their tributaries. The first legislation proposed was the Applebybill, H.R.7369, designed particularly to prevent the oil pollution of coastal waters. It contained the following provisions, which the coal men regarded as referring to the coal industry. It shall be unlawful to throw ... any refuse matter of any kind ... into any navigable waters of the United States or into any tributaries of any navigable waters from which the same shall float or be washed into such navigable waters. The chemical, steel, paper, and other manufacturing industries, as well as the mining industry, objected to this clause, the miners claiming that it would prevent the discharge of waste or mine drainage into any waters of the United States, for all streams or tributaries finally reach navigable waters. The next bill introduced was that of Congressman Briggs, H.R. 7430, an amendment to Section 13 of the Pollution Act of March 3, 1899. The original act referred chiefly to oil and oil refuse, but it provided also "that no material of any kind should be deposited on the bank of a navigable water, or tributary, which might reach the waters and interfere with or

Jan 1, 1923

By R. E. Head

Some mixtures of sulphide and oxide ores from the Tintic district in Utah are of a sufficiently good grade to be shipped to the smelter without beneficiation. In mining this type of ore, however, a material tonnage of ore of a similar composition but of lower grade is obtained. It is a question of economics whether such ore should be shipped with a certainty of a small return or concentrated if that would yield a sufficiently increased return to amortize plant construction and upkeep and yield a higher rate of profit than at present. It may be assumed that the tonnage of this borderline ore is constantly increasing and that eventually it will attain such proportions as to justify plans for milling on a relatively large scale. Under existing conditions, the producer of mixed sulphide and oxide ores is not greatly concerned about the physical characteristics of his ore or of its mineralogical complexities, since his contract with the smelter calls for payment on the basis of chemical analysis. When concentration is contemplated an entirely different picture is presented. Percentages of valuable metal content must then be con-sidered in terms of minerals, for it is in the form of minerals that recoveries are made and losses sustained. In describing the performance of a given flotation mill and reagent combination, it may be stated as a generality that a specific percentage recovery of valuable elements is made. Technically, however, the concentrator is really constructed and the reagents are selected to recover the valuable minerals. These considerations must be given prominence in discussing borderline ores from the Tintic district because of their physical characteristics and mineralogical composition. Because of these peculiarities they may be justly termed complex, since their lead, silver, and copper contents are each represented by two or more minerals of different chemical composition and presenting widely divergent physical properties. This paper sets forth the results of a microscopic study of a type of borderline ore from the Tintic district that is now being treated by direct smelting. A

Jan 1, 1939