Search Documents

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company's property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By Walter Dake

THE mining engineer is being more generally called on to examine and report on properties where the introduction of mechanical loaders is proposed, and as the use of these labor-saving devices presents an entirely different problem from that of hand-loading, an outline of procedure is herewith pre¬sented based on five years of intensive field experience in making such studies. It is impossible to outline an examination which will cover every condition but the most important variables are noted and the re¬port may be amplified or abridged to suit individual mine requirements. There are, of course, exceptional cases in which a single minor variable will determine the final conclusion; the result of mechanical loader application can be, estimated within close limits by considering all variables listed and taking into account the sum of all those found to be applicable to the property under examination. It is necessary that a high degree of accuracy be exercised in the analysis of conditions, and that a relatively narrow margin be figured on all estimates of tonnage outputs and costs. In making an examination for this purpose the data as to company name, business address, name of mine, geographical location, rail or water connections, type of mine (whether shaft, slope, or drift), and the name of seam should, of course, be included, to be followed by the minimum, maximum, and average thickness of seam, a brief description of the charac¬teristics of the coal, the impurities contained, location of regular impurities or partings, together with nota¬tion as to quality, uses, and-markets for the coal. It is also necessary to make cross-sections of the seam so that face preparation may be studied in an effort to eliminate all regularly-occurring impurities at the working place. The possibilities for further cost re¬ductions by the removal and gobbling of partings under¬ground before mechanically ? loading out a face are sufficiently great to warrant careful study and analysis. The classification of the mine from the standpoint of gaseous or non-gaseous operation will determine the general type of electrical equipment needed. A notation regarding the power whether generated at the mine or purchased, together with the amount, voltage, and type of current available is necessary since these matters determine the exact type of elec¬trical equipment to be used. A brief description of the ventilating system, giving type of fan, amount. of air delivered, water gage, and whether force or ex¬haust type, will enable the engineer' to figure venti¬lating requirements per man under mechanical loading practices. The pitch of seam in degrees, the pitch of working faces, and a brief description of rolls or horsebacks should be included, as these affect the efficiency of mechanical loading and, therefore, the economic re¬sults obtainable. -Notations should be made as to the amount of water found in working faces, and whether pumping, sprinkling or rock-dusting methods should be considered. As the character of the floor affects the operation of the machine at the face if a cater¬pillar-tread type, its hardness should be determined, and also whether impurities consisting of floor ma¬terial are likely to be loaded with the coal. The char¬acter of the roof and overlying stratification determine the mining system and width of roof span at work¬ing faces. It therefore directly regulates the amount of tonnage to be loaded by machines without a move from one place to another.

Jan 12, 1927

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company's property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By W. L. Falke, A. A. Cochran

A basic problem in connection with manganese is to find economical ways to utilize domestic resources. As a part of its program to conserve domestic mineral resources and to reduce dependence of foreign sources, the Bureau of Mines had conducted extensive research to broaden manganese technology and to find economical, technically-feasible processes for recovering manganese from these low-grade resources. This paper analyzes some of the major difficulties which have been encountered in previously proposed processes for treating low-grade manganese ores and discusses a process which may circumvent many of these difficulties. Vast deposits of low-grade manganese ore exist in the U.S., yet domestic production is insignificant compared to the more than 2 million tons of ore imported yearly into this country.' A basic problem in connection with manganese is to find economical ways to utilize domestic resources.2 As a part of its program to conserve domestic mineral resources and to reduce dependence on foreign sources, the Bureau of Mines has conducted extensive research to broaden manganese technology and to find economical, technically feasible processes for recovering manganese from these low-grade resources. Although a great many processes have been proposed for treating domestic manganese resources, a failing of many of them is that too many steps are involved for economical operation.' Some of the major processes that have been proposed were reviewed by Norman and Kirby.3,4 Chlorination processes have become increasingly useful as a means of recovering valuable metals from raw materials, because the relative cost of chlorine (Cl2) and hydrogen chloride (HC1) has decreased through the years, and because the corrosion resistance of materials of construction has been improved. The objective of these processes is to form metal chlorides that are more volatile or water-soluble than are the corresponding oxides or sulfides; these compounds then can be separated from the gangue or other minerals by volatilization or leaching. Several chlorination processes for the recovery of manganese have been investigated by the Bureau of Mines5-8 and others; the major chlorination processes were reviewed in 1963, and their main features were compared.4 In all these processes, the simultaneous leaching or volatilization of iron chlorides with manganese chloride (MnCl2) is a problem, and the more iron that is present, generally the greater the problem. The leaching step is not highly selective, and the product of this step is, at best, suitable only for the production of ferromanganese or for further processing to remove iron. The product of the volatilization step is, in all cases, a mixture of iron and manganese chlorides that contains too much iron even for ferromanganese production, and must undergo additional processing steps for iron removal. THERMODYNAMIC CONSIDERATIONS The literature indicates that the desired chlorination reactions will proceed at practical rates at temperatures near 1200°K (927°C). Free energy changes at 1200°K for the critical steps of the reduction and chlorination reactions9-11 follow: Most of the research on chlorination processes for manganese recovery has been done with HC1 rather than with C12, for the following three main reasons: 1) Recycling of the chlorinating agent, which is economically vital, appeared to be easier for HC1

Jan 1, 1968

By Arnulf Muan, D. P. Masse

PHASE relations in the system CoO-SiO2 have been determined as a basis for further investigations of thermodynamic properties of olivine solid solutions involving Co2SiO4 as a component. Previous data on the system CoO-SiO2 are incomplete or uncertain. Biltz and Lemke1 determined the melting point of cobalt orthosilicate as 1345°C , but Asanti and Kohlmeyer2 have later found a considerably higher temperature, 1420°C. The latter authors also studied melting relations of one mixture on the CO side and two mixtures on the SiO2 side of the orthosilicate composition and sketched a tentative phase diagram for a limited composition range of the system. However, no phase identification was carried out, and the authors left unanswered the question of the possible existence of a stable meta-silicate phase. Greig3 showed that a 90 wt pct SiO2-10 wt pct Co mixture at 1725°C consists of two immiscible liquid phases. The quenching technique was used in the present investigation. Mixtures of high-purity cobalt oxide ("Fisher Certified") and dehydrated silicic acid ("Baker Analyzed") were equilibrated in air atmosphere. The samples were then quenched to room temperature and the phases present were identified by microscopic and X-ray examination. The samples were kept in small envelopes made from thin (0.0004 in.) platinum foil. Thermodynamic data which have become available recently for Pt-Co alloys4 were used to check that the losses of COO from the oxide samples by alloying of cobalt with platinum in the present investigation were too small to change significantly the compositions of the oxide material during the equilibration. A vertical tube furnace with an 80 pct Pt 20 pct Rh resistance winding was used in runs up to 1510°C. Temperatures in these runs were measured with a Pt vs 90 pct Pt 10 pct Rh thermocouple calibrated against the melting point of diopside (CaMgSi2O6, 1391.5?C). The given temperatures as measured by this technique are estimated to be accurate to *5°C. Quench runs at temperatures above 1650°C were made with a modified Roberts and Morey5 strip furnace, using strip resistors composed of a 60 pct Pt-40 pct Rh alloy. Temperatures were measured with an optical pyrometer which was calibrated against the liquidus temperature of a mixture composed of 10 wt pct CaO, 90 wt pct SiO2 (1707°C). The temperatures measured with this technique have an estimated accuracy of +15°C. The results are shown graphically in Fig. 1. Only one intermediate phase, the orthosilicate Co2SiO4 with olivine-type structure, is stable in addition to the end members cobalt oxide and silica. The melting point of the orthosilicate was found to be 1415" ± 5°C. The metastilicate CoSiO3 is not stable at the temperatures of the present investigation. The two eutectic points in the system CoO-SiO2 where COO plus olivine, and olivine plus silica, coexist with liquid were found to be 72 wt pct COO and 1407°C and 63 wt pct COO and 1381°C, respectively. The melting point of cobalt oxide in air was taken as 1745?C, based on the previous data of Aukrust and Muan.6 Within limits of error (+ 5?C), identical eutectic temperatures to those determined in air were found when two representative mixtures were equilibrated at 1 atm O2 pressure and in an atmosphere of 84 vol pct CO2, 16 vol pct H2. This suggests that changes in oxidation state of cobalt in the condensed phases are not significant as far as their effect on the phase relations are concerned. This inference was substantiated by failure to detect7 any "excess oxygen" (i.e., oxygen in excess of that contained in Co2SiO4) in a sample of orthosilicate composition equilibrated in air 10°C above the liquidus temperature and subsequently quenched to room temperature. This work was carried out as part of a research program sponsored by the U.S. Atomic Energy Commission under Contract No. AT(30-1)-2781.

Jan 1, 1965

By K. E. Manchester, A. H. Clark

Hall measurements have been made on three groups of silicon samples, which were implanted with boron, aluininunz, and phosphorus ions. Boron and phosphorus implants show essentially bulk properties when annealed under previously determined conditions, i.e., 15 min at 80O°C for boron and 10 mirz at 600°C for phosphorus. Bulk properties were also observed in alu?rrilzum-implanted samples when ion concentrations were below 1015 cm-'; however, strange low- terrzperalure behavior and a falloff in cavrier concenlralion was observed for sarnples with ion concenlration abozle loL5 ern-'. This can be attributed to solid-solubility effects since the average bulk concentration f0.r the sample exhibiting bulk properties was below the reported solubility limit for aluminum, while the other samples were above the limit. A detailed study of the annealirzg process indicates that mobilities reach bulk c~alues in phosphorus implants at 250DC, in alutninurn ivnplanls a1 500°C, and in boron implants at 700°C. A simple rnodel has been proposed to fit the annealing data. THE technique of semiconductor doping by direct injection of energetic ions is being actively investigated at this Center. Previously published results from this laboratory have been concerned with the investigation of implanted profiles in silicon and the electrical properties of the resultant p-n structures.1'2 Diode properties have been reported for junctions produced by implantation of boron ions and aluminum ions in n-type silicon and phosphorus ions in p-type silicon. Reverse current characteristics, as well as electron diffraction data, have indicated that the damage to the structure produced by the energetic ions during the stopping process can be minimized by a gentle anneal. The time-temperature conditions for this process have been determined by sheet resistivity studies.3 Electrical profiles of implanted phosphorus ions which have been determined by a differential sheet conductivity technique are based on the assumption that the carrier mobilities and activation energies for ionization are the same as in bulk silicon. These assumptions have been substantiated experimentally by measurement of Hall constants and resistivities of these implanted structures and the results are presented herein. After establishing the bulk property equivalence of the annealed layers, a more detailed examination of the annealing process was undertaken. The sheet resistivity technique initially used to determine anneal conditions has been broadened to include Hall constants and mobility behavior with anneal conditions. PROCEDURE The three groups of samples prepared for Hall measurements were implanted with mass-separated beams of boron, aluminum, and phosphorus ions. Ion concentrations are equivalent surface concentration and they have been determined from beam current measurements during implantation. Implant conditions for the samples are shown in Table I. In all cases, the samples had previously been angle-lapped on one edge and the junction delineated with an HF-copper sulfate solution. The surfaces of the implanted regions of the samples were exposed to the delineating solution and in the case of the "n"-type phosphorus-implanted areas it was later discovered that a finite amount of surface could be etched by this solution. This is discussed in the section on results. The implanted samples were ultrasonically cut into the conventional six-probe configuration shown in Fig. l.* In the annealing studies, for which the meas- urements were taken at room temperature, the sample holder was a Bakelite jig incorporating tungsten mechanical probes. The other measurements were taken using a conventional liquid-nitrogen cryostat, in which the temperature could be varied from 77" to about 400°K. For these measurements, 10-mil aluminum dots were evaporated onto the samples and alloyed with the silicon at 530°C for 15 min. The samples were then mounted in flat-packs, and gold wires were bonded to the aluminum dots. The electrical measurements were made with either a Leeds & Northrup K-5 Potentiometer, a Keithley 147 Nanovolt Null Detector, or a Keithley 601 Electrometer. No external bias was applied to the substrate. There is an inherent self-biasing arrangement at one or the other of the current contacts (depending upon the polarity), and this suffices to limit the current flow to the implanted layer. The magnetic field was generated by an A. D. Little electromagnet. Except for occasional checks of linearity of the Hall voltage with

Jan 1, 1969

By Walter R. Hibbard, Harold Margolin

The effect of ten ternary additions on the aging of a Cu-Ag alloy was measured by X ray, microstructure and hardness. A supersaturated copper-rich transition structure was found. The effect of the ternary element was related to differences between transition and precipitate lattice parameters and analogies with solution and strain hardening. IN addition to the prerequisite of diminishing solid solubility with falling temperature, the theory of coherency hardening1 proposes that the principal source of hardening during precipitation is strain caused by coherency between the matrix and precipitate. For a given system greater coherency hardening would result from lengthening the period of coherent growth and/or increasing the number of nuclei, other things remaining equal. However, the hardness change during aging is a function of a number of phenomena in addition to coherency hardening, such as dispersion hardening, loss of coherency, solute depletion, matrix recovery or recrystal-lization, coalescence, and their relative time sequences. The present investigation was undertaken to study the effect of ternary additions on the age-hardening of Cu-Ag alloy. For this purpose a series of alloys were made containing as ternary constituents Mg, Al, Si, P, Mn, Ni, Zn, As, In, and Sb. These elements were added to a master 5 wt pct Ag in Cu alloy in such amounts as to obtain alloys listed in Table II containing the following approximate atomic percentages: 96 pct Cu, 3 pct Ag, 1 pct ternary addition. A 97 atomic pct Cu, 3 atomic pct Ag alloy was used as a comparison standard. There have been numerous investigations of age-hardening in Cu-Ag alloys2-lo but few of ternary Cu-Ag alloys. Pfister and Weist" found that 1 wt pct Ni reduced the solubility of Ag in Cu above 600 °C and that the rate of precipitation was slower than in polycrystalline Cu-Ag alloys of similar silver content. More recently Hodge, Jaffee, Dunleavy, and Ogden12 investigated the effect of ternary additions of Mg, Li, P, Cd, Zn, Zr and Be on strength properties of Cu-Ag alloys. Mg, Cd, and P were found to increase strength in the aged and cold-worked condition. Experimental Procedure Charges weighing 7.5 lb were melted in a closed carbon crucible under a reducing atmosphere* of nitrogen and hydrogen. A Durville-type casting procedure with a hot-top arrangement was used to obtain a sound casting, 2x2x43/4 in. Prior to rolling and annealing of the ingots, a trial solution anneal of rolled sections of the hot-top portions indicated that at 780°C melting was avoided except for the Cu-Ag-Sb alloy. This alloy could not be produced as a single phase within the limits of temperature control. i 3" to 5oC, since melting occurred at 64O °C, and below this temperature precipitation was

Jan 1, 1952

By H. E. Cline, E. F. Koch, J. L. Walter

It has been postulated and, in a few instances shown, that some kind of dislocation structure will be present at semicoherent interfaces to accommodate small lattice mismatches. In the present study of the NiAl-Cr eutectic, regular arrays of interface dislocations are observed at the boundary between the chromium-rich rods and the NiAl-rich matrix. The networks were examined by transmission electron microscopy and selected area diffraction. The rods and the matrix have a crystallographic relationship in which all directions and planes of the two phases are parallel. The dislocation networks are cmposed of a<100> dislocations lying on the intersections of the cylinders with (100) planes. Dislocations forming hexagonal rather than square arrays are also observed at certain areas of the network. The morphology of the network is consistent with the interpretation of mismatch being accommodated by interface dislocations in the cylindrical geometry. The measured spacing between dislocations was used to calculate an apparent lattice mismatch between the phases (˜0.35 PCt)interface network energy (-140 ergs per sq cm), and network strengthening (-10,000 psi). It has been proposed by Frank and Van der Merwe1 that dislocations should be present at the boundary between two semicoherent crystallographically related phases. The role of the interface dislocations would be to reduce the internal stresses, caused by the mismatch in atomic spacing across the interface. Such dislocations have been observed at the interface between expitaxially grown films and Substrates.2-4 Interfacial dislocations have also been observed at precipitate-matrix interfaces.&apos;-&apos; Directionally solidified eutectics have been shown to have semicoherent phases1&apos; and would, therefore, be expected to have interfacial dislocations as found by Weatherly at a lamellar fault in A1-A12Cu.11 The NiAl-Cr eutectic appeared to be a promising system to examine because both phases are cubic, the lattice mismatch is small, and the phases are crys-tallographically related. Furthermore, the eutectic is easily thinned for transmission microscopy. Indeed, interfacial dislocations were observed and this report describes the nature of the dislocation networks in the boundary between the NiAl-rich ma-trix-phase and the fine chromium-rich rods.21 I) EXPERIMENTAL PROCEDURE Ingots, 3/4 in. in diam and 6 in. long were made by melting in vacuum and casting under argon using 99.9 pct pure material. The composition, in at. pct, was 33 pct Ni, 33 pct Al, and 34 pct Cr. The ingots were then placed in A1203 crucibles on a water-cooled base, melted by means of induction, and withdrawn from the hot zone at the rate of 1 in per hr under argon.* * T his material was first directionally solidified in this laboratory by E. R. Stover Slices were taken perpendicular to the growth direction of the directionally solidified ingot for metallography and for transmission electron microscopy. The electron transmission samples were thinned mechanically, then thinned electrolytically in A-2 electrolyte* *A-2 electrolyte: 62 ml perchloric acid, 700 ml ethanol, 100 ml butylcellosolve, 137 ml distilled H20. until a hole appeared in the foil. 11) EXPERIMENTAL RESULTS A) Optical Microscopy. The microstructure, viewed on a plane perpendicular to the growth direction, is shown in Fig. 1. The structure consists of cells or colonies of parallel chromium-rich rods in the NiAl matrix. The cells occur when there are impurities present12 or, in a ternary eutectic, if the composition is slightly off the eutectic composition. The axis of the chromium-rich rods is parallel to the growth direction except near the cell boundaries. Here the rods may assume angles to the growth direction; however, examination shows that the crystallographic relationship between the rod and the matrix remains the same. Fig. 1 includes cell boundaries where the rods formed at a large angle to the growth direction. The variation of rod position across the cells made it possible to Fig. 1-Structure on plane perpendicular to growth direction. Rods near cell walls are at large angle to growth direction. Magnification 315 times.

Jan 1, 1970

By Dwight H. Seely, Louis R. Records

A process for low-temperature dehydration of natural gas utilizing Joule-Thomson effect in expansion through a throttling orifice has been tested in a full-scale field installation. The results of these tests are presented in the form of performance curves from which the process may be easily evaluated. The effect of separation temperature on condensate recovery from the process is also shown. INTRODUCTION The transportation of natural gas from producing well to the consumer has always encountered the problem of hydrate prevention. This problem has become increasingly important in the past ten years due to the rapid increase in produced gas volumes, production pressures, transportation pressures and distance from producing wells to consumer. Natural gas, as normally produced from gas or gas-condensate wells, is saturated with water vapor at well-head conditions of temuerature and pressure. The solution of the hydrate problem require; but one basic process — dehydration of the gas to a water content which will result in a water dew-point below the minimum temperature to be encountered from the producing well to the point of consumption. Much of the recent development of gas and gas-condensate reserves in the Gulf Coast Area has been in locations which are accessible only by water. High well-head pressures, pipeline construction and maintenance costs and the desirability of final central gas-condensate separation facilities have stimulated the development of dehydration equipment which can be installed at each well and which will permit hydrate-free transportation of both gas and condensate in the same line to central facilities. There are four types of natural gas dehydration processes now used: 1. Adsorptive processes. 2. Absorptive processes. 3. Chemical reaction processes. 4. Refrigeration processes. The first three of these processes are indirect in that they require use of adsorbents, absorbents or reactive chemicals. These materials require regeneration and part of the total gas stream is consumed in the regenerative process. Indirect processes have a wide range of flexibility as defined by allowable operating pressure and temperature, but most are not easily adapted to automatic operation. The refrigeration process described in this paper was designed for installation at the producing well-head. It requires no regenerative cycle and with normal well-head temperatures no external source of heat. The flexibility of this process is limited only by the pressure drop which may be allowed between well-head and transportation line. THEORY There are three basic physical concepts involved in the low temperature dehydration process. These are: 1. Formation of hydrocarbon hydrates. 2. Joule-Thompson effect resulting from the expansion of gaseous mixtures through a throttling orifice. 3. The equilibrium composition characteristics of water vapor and gaseous hydrocarbon mixture.. The chemical composition and physical structure of hydrate; have been described by several investigators.3,4,5,10 Specific conditions of temperature, pressure and composition as well as the requirements for turbulence and presence of free water necessary for hydrate formation have been described by Katz.6 Natural gas hydrates, as they are found in plugged gas pipe lines, have the appearance of packed snow. The mass of these hydrates has low continuous porosity and permeability. Joule-Thomson effect. or the reduction in temperature which occurs when natural gas is throttled throusll a restrictive orifice, is the basic phenomenon which permits efficient use of refrigeration for the purpose of dehydrating natural gas. Joule-Thomson coefficients for gafeous mixture; of methane with ethane and with butane have been reported by Buder.-I~olzer, Sage and Lacey.2 Brown1 predicted temperature drops for pressure drops from enthalpy-entropy calculations. Aside from this work there were no fundamental data found which would be applicable to natural gas mixtures of varying spe-

Jan 1, 1951

By Dwight H. Seely, Louis R. Records

A process for low-temperature dehydration of natural gas utilizing Joule-Thomson effect in expansion through a throttling orifice has been tested in a full-scale field installation. The results of these tests are presented in the form of performance curves from which the process may be easily evaluated. The effect of separation temperature on condensate recovery from the process is also shown. INTRODUCTION The transportation of natural gas from producing well to the consumer has always encountered the problem of hydrate prevention. This problem has become increasingly important in the past ten years due to the rapid increase in produced gas volumes, production pressures, transportation pressures and distance from producing wells to consumer. Natural gas, as normally produced from gas or gas-condensate wells, is saturated with water vapor at well-head conditions of temuerature and pressure. The solution of the hydrate problem require; but one basic process — dehydration of the gas to a water content which will result in a water dew-point below the minimum temperature to be encountered from the producing well to the point of consumption. Much of the recent development of gas and gas-condensate reserves in the Gulf Coast Area has been in locations which are accessible only by water. High well-head pressures, pipeline construction and maintenance costs and the desirability of final central gas-condensate separation facilities have stimulated the development of dehydration equipment which can be installed at each well and which will permit hydrate-free transportation of both gas and condensate in the same line to central facilities. There are four types of natural gas dehydration processes now used: 1. Adsorptive processes. 2. Absorptive processes. 3. Chemical reaction processes. 4. Refrigeration processes. The first three of these processes are indirect in that they require use of adsorbents, absorbents or reactive chemicals. These materials require regeneration and part of the total gas stream is consumed in the regenerative process. Indirect processes have a wide range of flexibility as defined by allowable operating pressure and temperature, but most are not easily adapted to automatic operation. The refrigeration process described in this paper was designed for installation at the producing well-head. It requires no regenerative cycle and with normal well-head temperatures no external source of heat. The flexibility of this process is limited only by the pressure drop which may be allowed between well-head and transportation line. THEORY There are three basic physical concepts involved in the low temperature dehydration process. These are: 1. Formation of hydrocarbon hydrates. 2. Joule-Thompson effect resulting from the expansion of gaseous mixtures through a throttling orifice. 3. The equilibrium composition characteristics of water vapor and gaseous hydrocarbon mixture.. The chemical composition and physical structure of hydrate; have been described by several investigators.3,4,5,10 Specific conditions of temperature, pressure and composition as well as the requirements for turbulence and presence of free water necessary for hydrate formation have been described by Katz.6 Natural gas hydrates, as they are found in plugged gas pipe lines, have the appearance of packed snow. The mass of these hydrates has low continuous porosity and permeability. Joule-Thomson effect. or the reduction in temperature which occurs when natural gas is throttled throusll a restrictive orifice, is the basic phenomenon which permits efficient use of refrigeration for the purpose of dehydrating natural gas. Joule-Thomson coefficients for gafeous mixture; of methane with ethane and with butane have been reported by Buder.-I~olzer, Sage and Lacey.2 Brown1 predicted temperature drops for pressure drops from enthalpy-entropy calculations. Aside from this work there were no fundamental data found which would be applicable to natural gas mixtures of varying spe-

Jan 1, 1951

By E. G. Woods, A. G. Comer

A mathematical model is presented and solved for determinution of the saturation distribution and pressure in a radial gas-storage reservoir. The model consists basically of two parts: (I) the growing gas-bubble core, and (2) the surrounding aquifer. Since the total pressure at the injection well is a function of the two-phase flow in the gas bubble and the unsteady single-phase flow in the aquifer, the resistance to flow in both zones was taken into consideration. The assumptions involved for both the radial equivalent of the Buckley-Leverett two-phase-flow equation and the injection-pressure equation are as follows: (I) the geometry is radial, (2) the gas bubble is free to expand or contract, (3) compression or expansion of the gas within the bubble may occur at the beginning of a time step, (4) the fluids are immiscible, (5) water is incompressible within the gas-storage region whereas it is compressible outside of this region, (6) a stable gas-water interface exists and (7) gas injection occurs at a constant rate or a series of constant rates. The mathematical model was solved numerically using an IBM 650 computer. A comparison is presented between the predicted results of the model, the results assuming steady-state flow and the actual initial injection-pressure history of an operating reservoir. Using the initial field pressure for a basis, the average deviation between the predicted pressure and the actual field pressure was less than 4.3 per cent. INTRODUCTION Underground storage of natural gas in abandoned oil fields, in abandoned coal mines, in caverns and in aquifers has had varying degrees of success. The lack of these first three facilities in the vicinity of most major gas marketing areas is leading more and more to storage in virgin aquifers. For the most part, this storage in aquifers has led to the study upon which this paper is based. Several excellent papers have been published discussing the problems involved in the underground storage of natural gas; however, to these writers&apos; knowledge, none of them considered the two-phase flow of fluids in the gas bubble and the fact that the gas bubble will grow or shrink in size depending upon the injection and withdrawal history of the reservoir. Not only will both of these factors influence the required injection pressure, but also they will have a definite bearing upon the amount of water production occurring upon withdrawal from the storage area. To solve this problem on an IBM 650 computer, several simplifying assumptions were made. Only the drainage portion of the relative-permeability curve was considered, thereby neglecting any hysteresis effects introduced during an imbibition cycle. The quantity of gas withdrawn during the period of the field study was only a small percentage of the total gas in place; therefore, this assumption is justified. For the problem studied in this case, the combined effects of capillarity and gravity were assumed to be negligible. This assumption becomes less valid as the formation thickness or the average pore diameter increases markedly. The justification of these assumptions should be studied in each case. THEORY This mathematical model for the prediction of saturation distribution and pressure for a radial gas-storage aquifer is based upon the equations for radial two-phase fluid flow&apos;.&apos; and for radial, unsteady-state, single-phase fluid flow.&apos; The two-phase flow is considered to take place in a "core" whose radius is equal to the maximum radius that the gas zone will attain, as indicated in Fig. 1. The injection-withdrawal history is approximated by a series of constant flow rates. Within the "core", gas is assumed to behave as a semi-compressible fluid; that is, the gas is assumed to have a constant density based on the average gas-zone pressure for the flow period. Between each constant-rate time increment, the gas density is allowed to change. This involves an iterative solution of the pressure equation. The liquid phase in this zone is considered to be incompressible, whereas it behaves as a compressible liquid outside of this region. The equations of incompressible flow in the "core" may be written for the gas phase

By R. T. Hukki

This paper presents a series of equations for mechanical ball wear, relating parameters of ball size, mill speed, and mill diameter. The fundamental equation, Eq. 12, presented here is introduced to correlate these basic parameters and thus define and clarify the concept of ball wear. This equation is offered as a general rule, which may be modified to apply to individual problems of grinding. BALL wear as observed in grinding installations is the combined result of mechanical wear and corrosion. Corrosion should be a linear function of the ball surface available. Ball corrosion, however, has been studied so little that its effect, although of great importance, cannot be included in the analyses given here. In a separate paper&apos; it is shown that 1 n = 0.7663 np----=— rpm [1] vD P = c, np D kw [2] T=c²(np)n De tph [3] In these equations n — actual mill speed, rpm np = calculated percentage critical speed D = ID of mill in feet P = power required to operate a mill, kw T = capacity of a mill, tph C¹ and c² - appropriate constants in = exponent of numerical value of 1 5 m 1.5 Exponent m is the slope of a straight line on logarithmic paper relating mill speed (on the abscissa) and mill capacity (on the ordinate). It is generally accepted, although not sharply defined, that ball wear in mills running at low (cascading) speeds is a function of the ball surface available. Accordingly, the wear of a single ball may be considered to be a homogeneous, linear function of its surface and of the distance traveled. Thus dw = f¹(d2) . f2(ds) [4] where dw is the wear of a single ball in time dt, d the diameter of the average ball in ball charge, and ds the distance traveled by the ball in time dt. Indicating that ds - a D n dt, the wear of the average ball in time dt becomes dw = f¹(d2) . f2(Dn dt) 1 --- f¹ (d1) f² (D c3 np-----— dt) \/D = c,d² n, D dt The rate of wear of the average ball is given by dw/dt. dw/dt = c, d² np D lb per hr [5] The weight of the ball charge per unit of mill length is a function of D The number of balls of size d in the ball charge is = f³(D2)/f4(d³). The rate of wear of the total ball charge equals the number of balls times rate of wear of the average ball. Thus rate of total ball wear = — . (dw/dt) w. c, . (l/d) . n,, D lb per hr [6] which is the equation of ball wear in low speed mills. In a mill running at a low speed, grinding is the result of rubbing action within the ball mass and between the ball mass and mill liners. When the speed of the mill is gradually increased toward the critical, the impacting effect of freely falling balls becomes increasingly prominent in comparison with the rubbing action. Reduction of ore takes place partly by rubbing, partly by impact. The share of the freely falling balls in the reduction of ore reaches its practical maximum at a speed somewhat less than the critical; at that speed grinding by rubbing has decreased to a low value. It may be reasonable to think that size reduction by freely falling balls should reach its theoretical maximum at the critical speed, if the fall of the balls were not hindered by the shell of the mill beyond the top point; grinding by rubbing would cease at the critical speed. As a first approximation, wear of freely falling balls may be considered to be a homogeneous, linear function of the force at which they strike pieces of rock and other balls at the toe of the ball charge. The force equals mass times acceleration. The mass of a ball is a function of d3 and its acceleration is a function of the peripheral speed of the mill. The wear of a single ball of size d representing the average ball in a ball charge will therefore be w¹ = f3(F) = f (d3) f7 (v). [7] Indicating that v = D n, and n = c³ np 1/vD, Eq. 7 becomes W1 = cn d3 np Do.5 lb per hr. [8] Total wear of the ball charge equals number of balls times the wear of the average ball. Number of

Jan 1, 1955

By S. T. Wlodek, John Wulff

Dense, adherent, and ductile coatings of chromium can be applied to Molybdenum by selectively freezing out the chromium solute from a supersaturated copper-or tin-rich liquid alloy. The successful exploitation of this technique depends on the control of variables common to any freezing process. Under the most favorable combimtion of supersaturation, nucleation, and mass-transfey, coatings as thick as 0.004 in. can be obtained. In exploratory experiments it was found that a coating of chromium may be applied to molybdenum by immersing the molybdenum body in a supercooled copper-chromium or tin-chromium melt and selectively freezing out the contained chromium onto the molybdenum body. Supercooling of the liquid metal plating bath can be achieved by cooling, or the maintenance of thermal or concentration gradients in the melt. The technique is similar to conventional dip-plating procedures where the sample is immersed in a molten bath of the pure plating medium, except that in these studies, the plating medium consisted of a dilute solution of chromium in liquid tin or copper. The success of this method requires that the base material to be plated be isomorphous with the coating and insoluble in the plating bath. In addition, the plating bath, while having an appreciable solubility for the coating component, must have negligible solid solubility in the solid plate. Such relationships exist in the molybdenum-chromium, chromium-tin, and chromium-copper systems. Liquid tin and copper are satisfactory as the plating solvent, because although chromium is appreciably soluble in both of these liquid metals, solid inter-solubility is almost negligible, and no compound formation occurs. The same relationships exist between molybdenum and copper or tin except that the solubility of molybdenum in liquid tin or copper is insignificant. It is this combination of solubility relationships, as well as the completely isomorphous nature of the molybdenum-chromium system, which allows the formation of a chromium coating on molybdenum by the selective freezing mechanism. Since the main deterrent to the widespread use of molybdenum for high-temperature structural applications is its poor oxidation resistance, the formation of a dense and ductile chromium coating on molybdenum may well be of commercial significance. In addition, the basic principle of coating formation by selective freezing should be applicable to other metallic or even nonmetallic systems. The precipitation of the solute from a liquid metallic solution, for the formation of a protective coating, has not been previously considered in the literature. Frequently, however, a similar phenomenon has been described in the corrosion of metallic heat exchangers by liquid metals1 wherein temperature gradients in the liquid metal heat-transfer medium result in the formation of layers or deposits of metallic residue2 in the cooler portions of the system. Impregnating techniques using liquid baths have been tried as a plating process. Semchyshen and Barr, for instance, have successfully diffused chromium into molybdenum by immersing the molybdenum specimen in a liquid tin-chromium or copper-chromium alloy. This simple holding technique fails to produce a layer of pure chromium and requires prolonged immersion to allow for the diffusion-activated enrichment of the molybdenum. During the course of this investigation, most of the phase relations published for the copper-chromium4 and molybdenum-chromium4 systems, were found reliable. It was necessary, however, to investigate the solubilities of chromium and molybdenum in liquid tin as well as the solubility of molybdenum in liquid copper. These determinations were made by a simpie weight loss technique on materials of the same purity as used in the plating studies. The results of these solubility studies are given in Tables I and I1 and indicate that although the solubility of molybdenum in liquid

Jan 1, 1961

By Leonard L. Melton, Calvin D. Saunders

The design and performance of many operations common to the petroleum industry depend upon the unique properties of a class of materials known as non-Newtonian fluids. The art of measuring and describing these properties, called rheology, has fallen far behind the field applica-tion of these fluids in this industry. Empirical methods are still employed although theoretically sound methods of analysis are now available. This paper illustrates a completely general method of analysis of the rheological properties of non-Newtonian fluids which id independent of the type of viscometer employed and also the rheological type of fluid encountered except those of a thixo-tropic or rheopectic nature. Values of the rheological properties of a fluid obtained using this method of analysis are based upon an absolute scale of measurement, eliminating the necessity of employ-jng arbitrary concepts of the flow properties of non-Newtonian fluids, The fundamental nature of this method of analysis is further demonstrated by evaluating the precision with which measurements have been made of these rheological properties by employing a dimensionless criteric: —the Fanning friction factor-Reynolds number correlation. INTRODUCTION Non-Newtonian fluids are not new in the petroleum industry. Particular properties of non-Newtonian materials have been recognized and used to advantage in drilling fluids and have found excellent application in the hydraulic fracturing process.&apos;.&apos; While usage of these fluids is not new in this industry, the art of measuring and describing their rheological properties is still in its infancy. This is reflected in the accepted method of evaluating drilling fluids, API RP 29, (1950), which recommends a one point "viscosity" measurement. These shortcomings are recognized by various groups in the industry and more adequate methods have been prposed.3,4 The efforts Of these people are to be commended; but, at the same time, the limitations of their method of analysis and viscometer must be appreciated. This method Of analysis is applicable Only to Bingham plastic fluids as is pointed out early in their articles. The consistency of a Bingham plastic fluid must also lie within the range of the viscometer which is also well defined by the author. It is believed that the apparent simplicity of this method of analysis and the utility Of Operation Of their viscometer will soon make the terms non-Newtonian fluid and Bingham plastic fluid synonymous as used in this industry; a tendency which has already been encountered. Application of this method of analysis to a non-Newtonian fluid other than a Bingham plastic can lead to erroneous results. The field of rheology has long been hampered by the adherence to arbitrary concepts of Of of the flow properties Of non-Newtonian fluids. This has resulted in the design and operation of viscometers so as to fulfill these concepts rather than following the more logical method of analyzing experimental data so as to yield a fundamental truth. completely Bingham proposed the concept Of plastic flow and yield asu rement. data presented by Buckingham could hardly be interpreted so as to substantiate this theory; but rather succeeded in establishing the fact that compliance with this flow concept could never be realized in the capillary tube vis-cometer.5 Bingham, in reply, sug-gested "Rather than complicate our formula, it would seem to me a much better plan to so change the conditions of flow that the formula will be linear... Reiner0 stated .This plan has been followed by me in collaboration with Miss Riwlin. . . . From the present paper (Reiner and Riwlin, 1929) it will be seen that it is possible to choose the conditions of flow so that the formula based on Bingham&apos;s law of plastic flow remains linear. This is realized in the rotation viscometer," Thus, a viscometer, with design and operation based on the Reiner and Riwlin equation for plastic flow, is restricted to a specific range of flow

Jan 1, 1958

By R. N. Stevens

Any consideration of the errors involved in determination of ?gb by previous workers should discuss their experimental methods in terms of the appropriate theoretical equation; this the authors have not done in a number of cases. To facilitate the present

Jan 1, 1969

By Martin Weinstein

A technique is described for preparing finegrained lead telluride by ultrasonic agitation of a solidifying melt. Material prepared by this technique is dense and chemically homogeneous. N-type PbTe, containing 0.03 mole pct PbIz, has been made and its thermoelecCric Properties have been measured as a function of temperature. For comparison, the properties of similarly doped PbTe made by cold pressing and sintering, and by extrusion, have also been measured. The ultrasonically prepared material compares favorably with the others in its thermoelectric-efficiency factor. Comparison of compressive-flow curves for the three kinds of PbTe show that the ulhasonically prepared material has much superior ductility. The cleavage strength of the ultrasonic material is related to the grain size, D, by the Petch relation:Extrapolation to infinite grain diameter yields a fracture strength of 5000 psi for single-crystal PbTe. WHEN metals and semiconductors solidify in a mold they normally assume one of three cast structures illustrated in Fig. 1.&apos; Solidification in a casting starts at the mold walls where a large number of fine crystals of random orientation can be nucleated to form the chill zone. Because of the anisot-ropy of the growth rate, those crystals whose direction of maximum linear growth is parallel to that of the heat flow grow faster and crowd out the crystals of less favorable orientation. A second zone, having a preferred orientation, called the columnar zone, thus forms adjacent to the chill zone. The speed of growth of the columnar grains will depend, in the case of limited undercooling of the melt, on the rate at which heat can be abstracted. The columnar zone can extend to the center of the casting, Fig. l(a), but it is frequently followed, in solid-solution alloys, by another zone of equiaxed randomly oriented grains in the central portion of the casting, Fig. l(b). The equiaxed structure in Fig. l(c) represents the completely grain-refined case where the equiaxed grain size is small. The third type of structure is the most desirable because it imparts a somewhat higher strength for all except high-temperature applications, it reduces segregation of the doping constituent, and it reduces the possibility of hot tearing (the separation of grains due to the melting of a low-melting point constituent in the grain boundaries). In order to obtain fine-grained castings, the nu-cleation frequency must be increased and grain growth must be restricted. Various techniques have been employed for obtaining this end, namely: rapid cooling, vibration, and inoculation of the melt. The success of these techniques depends upon the characteristics of the metal species and on factors controlled by heat transfer through the crucible walls. Recent studies2" have shown that the application of ultrasonic energy to the solidifying ingot is an extremely powerful tool in the improvement of the crystalline structure of metallic castings. Both the mechanical properties and homogeneity of the ingots are improved. Ultrasonic oscillations may affect the crystallization process by 1) permitting subcritical nuclei to agglomerate and thus form nuclei of sufficient size to cause crystallization, 2) changing the state of surface adsorption of various catalysts found in the liquid melt, 3) breaking pieces of solid from the solidified surface near the supercooled region thereby increasing the number of possible nuclei, 4) causing temperature fluctuations to occur in certain parts of the melt thereby increasing the supercooling at specific points in the liquid, and 5) decreasing the critical nucleus size by increasing the pressure at specific points in the melt.&apos; Various investigators have concluded that the effectiveness of the ultrasonic oscillations results from cavitation which disrupts the growing solid-liquid interface The present paper describes the application of ultrasonic oscillations to the crystallization of the semiconductor N-type PbTe. The purpose of this study is to prepare crystalline

Jan 1, 1964

By ElRoy Nelson

WATER provides to many mineral industries functions similar to those performed by money in the economic system. Water is a medium of exchange. It is also required in chemical reaction for cooling, for transfer of minerals, and for cleaning. To a great extent, water is also a raw material in almost every industrial operation; it becomes a component of the finished product. In the Rocky Mountain region, water is treated with a great deal of respect. There has not been enough of it when needed. Long ago storage facilities were planned and devised to assure a supply during periods of shortages. This comes from the history of the region in irrigation and mineral processing. Within this region the shovel was always the most lethal weapon used in settling disputes over the use or misuse of water.

Jan 10, 1954

The nickel suppliers are hard at work across the entire spectrum of the industry-from exploration and mining on the one hand to the development of new applications of this unique metal on the other. The reason-a surging demand for nickel by the free world. Evidence of interest and activity in nickel abounds. Companies such as Anaconda, American Metal Climax, Kaiser Aluminum & Chemical, Patino, Newmont-firms that have not been in the nickel industry before-are now involved in various exploration and development ventures around the world. International Nickel, Falconbridge, Le Nickel and Sherritt Gordon-the big names in the industry -have committed vast sums of money and talent in a variety of new developments designed to ensure their status as leading producers of this commodity. As a result, the world is now seeing a rapid build- up in nickel capacity, and in this issue of [ ], the editors have prepared a summary of these fast- moving major developments.

Jan 10, 1968

HAVING told you about steel in the previous chapter, it seems to me necessary to speak here of brass for the same reason, for it bears the same relation to copper that steel does to iron. It is the opinion of some concerning both of these that they are true minerals because Pliny in his Natural History calls it aurichalcum and says that it has its own ore; he does not say, however, where it is found, and I have not heard from anyone else that it has been found anywhere, and, surely, if it had been found when he wrote, it would also be found today. Since I have no knowledge other than that gained through my own eyes, I tell you as a certainty that just as steel is iron converted by art into almost another kind of metal, so also brass is copper given a yellow color by art. Surely it was a splendid discovery, for which we must praise the alchemists,* although perhaps whoever discovered it was deceived, thinking that he had made gold from copper. Now, in short, this work requires infinite labor, and is carried out in various places, for instance, in Flanders, Cologne, Paris, and in many other countries, and also in the city of Milan in Italy, where I have seen a

Jan 1, 1942

By Fred H. Poettmann

The vaporization characteristics of carbon dioxide in a League City natural gas - Billings crude oil system were studied at three temperatures, 38°. 120°, and 202°F and for pressures ranging from 600 to 8,500 psi. Variation of carbon dioxide concentration up to 12 mole per cent in the composite showed no effect on the equilibrium vaporization ratios (K values) of the hydrocarbon constituents or on the K value of carbon dioxide itself. It was shown that carbon dioxide is more soluble in crudes than in distillates which is contrary to the behavior of methane. A working chart of carbon dioxide K values is presented. INTRODUCTION The study of the equilibrium vaporization ratios of mixtures of paraffin hydrocarbons has been rather thorough.2,6,7,8,9 In the past few years considerable attention has been paid to the vaporization characteristics of the so-called noncondensable gases such as nitrogen, carbon dioxide, and hydrogen sulfide in mixtures of hydrocarbons. since they usually occur to some extent in most crude oils and natural gases.1,3,4,5 Knowledge of this behavior is useful to both the production and refining phases of the petroleum industry. This paper reports the equilibrium vaporization ratios (K&apos;s) of carbon dioxide in a mixture of League City natural gas and Billings crude oil, and compares them to those obtained in a natural gas-distillate system. The equilibrium vaporization ratios for the hydrocarbon components in this system had previously been studied by Roland.&apos; In addition to the determination of the K values for carbon dioxide, the K values for methane and ethane were also determined in order to observe what effect, if any, the presence of carbon dioxide had on these K values. The concentration of carbon dioxide was also varied in order to observe the effect of this variable on the carbon dioxide K values. EXPERIMENTAL PROCEDURE The apparatus used in this study cotlsisted of a stainless steel equilibrium cell of about 2 liters capacity. The cell was mounted on trunions permitting rocking in a thermostatically controlled oil bath. Two high pressure valves fitted with steel tubing were mounted on the top of the cell. one was used for sampling the equilibrium gas phase and the other for sampling the equilibrium liquid phase by means of an induction tube within the cell. Stainless steel tubing from the bottom of the cell led to a mercury reservoir and manifold which was connected to a free-piston type pressure gauge manufac- lured by the American Instrunlent Ctr. and to a volumetric. putrip. The temperature of the oil bath was measured by means of a ralibrated mercury-in-glass thermometer. The recorded temperatures are believed to be accurate to ±0.5 °F. The pressures are correct to 22 psi. The crude oil used in this study was stock tank oil obtained from the Wilcox formation in the Billings Field, Noble County. Okla. The natural gas was obtained from the League City Field. Galveston County, Tex. The oil was treated with anhydrous calcium sulfate in order to remove the last traces of water. To insure a supply of constant composition gas at room temperature the cylinders of League City gas were cooled to about 30°F, inverted, and the condensed liquid was allowed to drain from the cylinders. The analysis of the gas and crude are tabulated in Table I. The carbon dioxide came from Pure Carbonic, Inc., and was .stated to have a purity of 99.5 per cent or better. The procedure used to obtain samples of the equilibrium liquid and vapor was similar to that employed by others making use of the rocking type equilibrium cell.6,7,8 The equilibrium cell was evacuated and calculated quantities of carbon dioxide, natural gas, and crude oil were charged to the cell to the desired pressure. In charging the equilibrium cell an attempt was made to maintain the ratio of the natural gas to crude oil as close as possible to that employed by Roland. After the cell was charged, samples of

Jan 1, 1951