Search Documents

By J. M. Campbell, T. S. Buxton

The most widely used methods of predicting the volumetric properties of gas are based on the principle of corresponding states, which asserts that the compressibility factor is a universal function of reduced temperature and pressure. Previous studies have shown that the acentric factor, as proposed by Pitzer, l is an important addition to reduced pressure and reduced temperature as factors affecting the compressibility factor. Results of this study indicate that, if the pseudocritical temperature and pressure used to determine the reduced conditions are adequately predicted, characterization of natural gas-carbon dioxide mixtures with the acentric factor will allow reliable determination of the compressibility factor. Comparisons of predicted and experimental compressibility factors have shown that the pseudo-critical constant rules of Stewart, Burkhardt and Voo 2 are satisfactory for hydrocarbon mixtures. However, these rules fail to predict the pseduo-critical constants for hydrocarbon-carbon dioxide mixtures. Based on graphically determined pseudocritical temperatures for binary hydrocarbon-carbon dioxide mixtures, a correlation which gives the required correction to the Stewart, Burkhardt and Voo rules was prepared and a compressibility factor prediction technique was proposed. To test the proposed technique, compressibility factors for live mixtures of methane, carbon dioxide and either ethne or propane were experimentally determined at 100, 130 and 160F and pressures up to 7,026 psia. The predicted and experimental compressibility factors for these live mixtures had an average absolute deviation of 0.55 percent. INTRODUCTION Two-parameter generalized correlations based on the principle of corresponding states (PCS) are presently available for reliably predicting the compressibility factor of lean natural gas, i.e., natural gas with low concentrations of hydrocarbons heavier than methane. When these same correlations are used for mixtures of natural gas and carbon dioxide, large deviations between actual and predicted compressibility factors are observed. This study was undertaken to provide a means for accurately predicting the compressibility factor for such mixtures. In the past, two avenues of approach have been employed to extend the applicability of the PCS. The first has been to introduce additional parameters. The second has been to develop combination rules for predicting pseudocritical constants which do not suffer from the limitations of the commonly used molal average constants. In this study, both of these approaches have been considered and employed to arrive at a method for predicting the compressibility factor of mixtures of hydrocarbons and carbon dioxide. SELECTION OF A THIRD PARAMETER Failure of the original PCS to predict the compressibility factor for all pure gases, regardless of their mass, shape or polar moment, has led to the introduction of additional parameters into the PCS. Parameters have been introduced to correct for quantum deviations,3-5 non-spherical or globular shapes6-9 and for polar moments.8-12 In addition to these parameters which are based on some microscopic property and intended to correct for some specific cause of deviation, more general parameters based on some bulk property have also been introduced.1913-16 To use additional parameters to correct for each of the possible causes of deviation among the individual constituents of a gas mixture would require a rather complex form of the PCS. To maintain the PCS in as simple a form as possible, it is more desirable to have a single third parameter which is based on some bulk property influenced by several of the factors causing deviations. The third parameter selected for use in this study is a factor originally proposed by Pitzer.9

By J. E. Spruiell, F. H. Patterson, B. F. Shuler

The microstructures and textures developed by the working of high-purzly thermochemically deposited tungstem sheet have been inuesligated. Greater than 60 pct reduction was required to deslroy the columnar grain structure which existed in the as-deposited sheet. With increasing reductions the texture gradu-ally charged from the initial as-deposited orientation with (100) parallel to the sheet normal to a (100}(011) ideal ovienlation with some spread about the rolling direction. This texture was retained after recrystalli-zation a1 2000°C. THE processes for depositing tungsten by hydrogen reduction of tungsten hexafluoride have been under development for the past several years.1,2 The nature of the deposition process is such that the as-deposited material contains a highly oriented columnar grain structure perpendicular to the deposition substrate. This well-defined columnar structure may be useful in certain applications293 but a wrought or equiaxed structure may be desired for some components such as tubing. Knowledge of the effects of working ther-mochemically deposited (TCD) tungsten is therefore necessary in order to establish the feasibility of obtaining worked and recrystallized microstructures and textures. The details of a recently developed technique for thermochemically depositing flat, uniformly thick tungsten sheet are presented with emphasis on the effects of deformation by rolling on the microstructure and texture. Although no work has been previously reported on the rolling and the annealing textures of TCD tungsten, there have been some determinations of textures for cold-rolled tungsten foil prepared from powder-metal -lurgy billets.4-8 The general description is that of a predominantly lurgy{100}(011) texture, with some spread about the rolling direction as an axis. pugh5 reports data both for cold-rolled and for annealed foil having about 96 pct initial cold work. He observed no change in texture, except for a decrease in the spread, for annealing treatments of 30 min at temperatures up to 1800°C. On annealing at 1900°C, both the low-temperature components plus new components which were described alternately as {001}(320) plus {001)(230) or as {100}(011) ± 12 deg about the sheet normal were observed. Above 1900°C, the new orientation existed alone, and it was stable up to 2500°C, the highest temperature that Pugh investigated. THERMOCHEMICAL DEPOSITION OF TUNGSTEN SHEET High-purity tungsten sheet was reproducibly deposited on the inner walls of a molybdenum mandrel by the thermochemical reaction WFs(g) + 3H2(g) - W(s) + 6HF(g). The mandrel was heated by a five-zone tube furnace which afforded a controllable fixed-temperature profile. Sheets measuring 1+ by 12 in. have been deposited with uniform thicknesses of up to 0.145 m. As shown schematically in Fig. 1, the purified reaction gases were metered into a mixing chamber at a Hz-to-WF6 ratio of 15 and preheated to 350°C. The flow rate of the WF6 was 300 cu cm per min at stp. These gases were directed through a conical injector into the deposition chamber. Inside this chamber hydrogen reduction of the WF6 to pure tungsten metal occurred on the hot walls of the molybdenum mandrel at a total pressure of 5 Torr. Typical temperatures for the five zones in the chamber were, respectively, 565", 540", 550°, 570°, and 590°C. The hydrogen fluorlde generated from the reaction, the excess hydrogen, and some un-reacted WF6 were pumped on through the scavenger

Jan 1, 1968

By R. G. Powell, R. Schuhmann, E. J. Michal

Liquidus surfaces in the ternary system FeO-Fe2O3-SiO2, were determined from 1250' to 1450°C by the procedure of equilibrating small samples in platinum crucibles, quenching, and microscopic examination. The experimental results were combined with previously published information to construct a ternary diagram for the system showing the entire temperature-composition range of stability of iron silicate slags. Metallurgical applications of the diagram, especially in copper smelting, are discussed briefly. IRON oxides are almost unique among the common oxide constituents of metallurgical slags in that the iron occurs in two different states of oxidation, ferrous and ferric. Moreover, in liquid slags the degree of oxidation of the iron is readily changed by reactions of the slags with oxidizing agents or reducing agents. This behavior of iron oxides in slags accounts, for example, for the effective transfer of large quantities of oxygen through slag layers in open hearth steelmaking. In this process, oxygen supplied by reactions at the gas-slag interface is dissolved in the slag with the oxidation of ferrous iron to ferric. Ferric oxide is transported across the slag layer by convection, and at the slag-metal interface the oxygen reacts with liquid metal while the ferric iron is reduced back to the ferrous state. Another group of processes in which variation in degree of oxidation of iron has great practical importance is in copper smelting. In matte smelting and converting, such large proportions of the iron are oxidized to the ferric state that problems are encountered in preventing or controlling the formation of solid magnetite. The ferrous-ferric relationship also affects the attack of iron oxides on high-SiO2 refractories, which appears to be most severe under reducing conditions for which ferrous iron predominates. Darken and Gurry' determined the chemical properties and phase equilibria of pure iron oxide slags. Their data show that iron oxide melts can have compositions ranging almost all the way from FeO to Fe2O3. The melts of lowest oxygen contents, which exist in equilibrium with metallic iron, approach ferrous oxide in composition but still have a small percentage of ferric oxide. The melts of highest oxygen contents, which have oxygen dissociation pressures of 1 atm, are above magnetite in oxygen content, with over two-thirds of the iron in the ferric state. The previously established phase diagrams for silicate slag systems all show FeO as the iron oxide component. However, Bowen and Schairer? who determined the FeO-SiO2 diagram and many of the other diagrams used by slag chemists, have been careful to point out that their systems always contained both ferrous and ferric iron. Thus, their data are for limiting mixtures with minimum contents of ferric iron, obtained by melting and equilibration in iron crucibles. Under these conditions, the Fe2O3 percentages found by analysis were small enough to justify simplification of the published phase diagrams by calculating the Fe2O3 to equivalent FeO and ignoring Fe2O3 as an additional component. On the basis of experimental measurements of melting points of iron oxides on silica in the presence of various gas mixtures, Darken3 worked out phase diagrams for the Fe-Si-0 system which show the important phase equilibria in terms of temperature and gas composition. This study clarified many aspects of the application of the phase rule to the FeO-Fe2Oa-SiO2 system and was an important basing

Jan 1, 1954

By C. E. Violet, R. J. Borg, E. M. Howard

The miscibility gap in the Au-Ni system has been determined by Mossbauer spectroscopy, with used as a probe. The phase boundaries were determined from the compositional dependence of both the isomer shift and Curie temperature. X-ray diffraction measurements were also used to confirm the Mossbauer results. 1 HE purpose of this research is to demonstrate the application of Mbssbauer spectroscopy to the determination of phase boundaries and to redetermine the miscibility gap by an independent and novel technique. The techniques evolved in this study are readily applicable to other polyphase systems and are generally as quick and accurate as the more conventional methods, e.g., metallography, X-ray diffraction, thermal analysis, and so forth. To be sure, not all polyphase systems will lend themselves favorably to Mijssbauer investigations, but this is a problem met in the use of conventional methods as well. The Mbssbauer spectrum responds to a different set of physical parameters, and consequently provides an entirely independent method of analysis. It is especially useful if the system has either a ferromagnetic or an antiferromagnetic transition. The Au-Ni system was selected because alloys containing more than -60 at. pct Ni become magnetically ordered at low temperatures; also the miscibility gap is quite well established (see Ref. 7 for a compilation of pertinent references, also Fig. 11, and thus provides a reliable test of this novel procedure. As Fe is the most commonly used Mijssbauer isotope, there exists a wealth of information concerning its behavior in iron-containing alloys and compounds. However, as yet there have been relatively few experiments using it as a probe to investigate nonferrous systems. By choosing a nonferrous alloy system, we are able to demonstrate that its use is not restricted to systems containing iron as one of the major constituents. Wertheim and ~ernick' have used the same method to investigate Cu-Ni, and demonstrated that one can obtain a systematic variation in the isomer shift and magnetic hyperfine field. However, we believe this to be the first time these techniques have been used to establish phase boundaries. Two hyperfine interactions were measured and used to determine the phase boundaries, viz., the magnetic hyperfine splitting and the isomer shift which in this alloy system are both strong functions of composition. Calibration curves were established based upon single-phase solid solutions obtained by quenching from temperatures well above the maximum of the miscibility gap, see Fig. 1. Solid solutions containing 25, 50, 65, 75, 85, 92, and 96 pct Ni as well as pure nickel were used in the calibration procedure. Fig. 2 shows the Curie temperature, TC, and the isomer shift, v,, as determined from the Mbssbauer spectra, and variation in lattice parameter as determined by X-ray diffraction, as functions of composition. The compositions of the two-phase systems quenched from temperatures within the miscibility gap are obtained by comparing their respective values of TC and v0 with the calibration data. I) EXPERIMENTAL Mbssbauer sources were made by fusing the component metals in a tungsten arc melter, which has a water-cooled copper hearth. Both nickel and gold were 99.999 pct pure, and the melting was done in an atmosphere of purified argon. The alloys were rolled, diced,

Jan 1, 1969

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and "{2,3,10)" or "(127)". (It is now thought1' that the "{0,1,13)" habit reported for the Fe-Ni-C alloys'' is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove.' The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and tj2 = vi (i = 1, 2, 3), the Kz qd 771 elements are given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics cij Iand cij reduce to the unit tensors 6ij and 6ij so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and 77~ are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963

By S. J. Rothman, J. J. Hines, D. Rokop, R. Bastar

Self-diffusion has been measured along each principal axis of mosaic-structured and relatively perfect a uvaniuln single crystals. The anisotropy reported before,' D[loo] = D[001] » D[010 , has been confirmed. and is shown to represent volume diffusion. Diffusion along the dislocations in the imperfect crystals increases the measured value of D significantly without changingr either the shapes of the penetvation plots or the anisotropy. SINCE a uranium is orthorhombic, the diffusion coefficients along the principal crystallographic axes need not be equal. A previous measurement of self-diffusion in three mosaic-structured a uranium single crystals1 showed that Dil00| =D[001 >>D[010 This result was deduced from penetration plots similar to those in Fig. 1. That is, the plots for diffusion along [loo] and [001] were the straight lines expected from the solution of the diffusion equation for the boundary and initial conditions of the experiment, while the plot for diffusion along [010] was curved so that the part near X = 0 had a much steeper slope than the straight lines did. The observed anisotropy could have been due either to volume diffusion or to diffusion along the very large number of dislocations in such crystals, according to the model proposed by aart.' The authors of Ref. 1 argued that the latter possibility was unlikely, but did not exclude it. To settle the question, a simultaneous measurement of self-diffusion in mosaic-structured and mosaic-free crystals was carried out. This paper reports the results, as well as a measurement of the temperature dependence of self-diffusion in a uranium. EXPERIMENTAL The single crystals of a uranium used in this experiment are listed in Table I, together with other experimental details. '(Mosaic structured" here means crystals grown by solid-state phase change.3 The Laue spots from such crystals spread over about 6 deg of arc, which indicates that the density of dislocations is very large. "Perfect" crystals are ones grown by Fisher's grain-coarsening tehnique; the Laue spots from these are quite sharp,4 which shows that the dislocation density in these crystals is much lower. All of the crystals were made from high-purity uranium; a typical analysis is given in Ref. 1. The actual diffusion directions were within a few degrees of the nominal. The thin layer-sectioning method was used. The experimental techniques were similar to those described in Ref. 1, except the sectioning. Crystals Za, 2b, 2c, 4a, 4b, and 4c were sectioned on a lathe. Crystals 3a, 3b, and 3c were sectioned by grinding on glass plates, with 1 p diamond powder in butyl alcohol as the abrasive. The use of glass plates eliminated the crowning noted in Ref. 1, and the use of butyl alcohol as a lubricant simplified the chemical processing of the sections. Material from the sides of these three crystals was removed by spark machining before sectioning. The sectioning of crystals 4a and 4c was botched. A small cylinder of metal was extruded from the center of crystal 4a while turning off material from the side of the sample. Crystal 4c was misaligned by 2.1 x 10"3 cm because the dial gage jammed during the alignment. Notwithstanding these errors, useful data were still obtained from these crystals. The points

Jan 1, 1967

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and It is now thought1' that the "{0,1,13)" habit reported for the Fe-Ni-C alloys'' is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove. The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics and reduce to the unit tensors and j so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963

By P. R. Sperry, P. A. Beck, Hsun Hu

As described by means of quantitative pole figures, the inside texture of highly rolled aluminum and copper strips may be approximately described by four equivalent ideal orientations near (123) [121]. If rolled in reversed passes, the surface texture of copper is also near (123) [121], that of aluminum is (100) [011]. The inside texture of highly rolled brass is (110) [112]. The surface texture is the same, if rolled in reversed passes. The surface texture of all three metals is related to the inside texture, but asymmetrical, if rolled without reversal between passes. MANY previous investigations dealing with the subject of the present work were reviewed by Wassermann.1 Barrett,2 Brick,3 and Richards.' The recent introduction of quantitative methods for pole figure determination by Decker, Asp, and Harker,5 Schulz5 and others made it possible to reinvestigate some of the finer points which the earlier more qualitative photographic methods left undecided. The rolling textures of silver and of 70-30 cartridge brass have been quite consistently characterized by the ideal orientation of (110) parallel to the plane of rolling and [112] parallel to the rolling direction. On the other hand, it has been recognized by several investigators that certain other face-centered cubic metals, such as copper and aluminum, developed rolling textures rather different from that of brass. These textures have been variously described by the following ideal orientations, singly or in combinations with each other: (110 [112]: (112) [111]; (135) [335]; (135) [211], etc. The discrepancies usually have been attributed to the lack of sharpness in the textures and to the attendant difficulty of associating "ideal orientations" with pole figures showing great scatter of orientations. It seemed desirable to investigate by the new quantitative methods to what extent the apparent lack of sharpness may have been brought about by the qualitative methods used previously, rather than by the textures themselves, and to decide, if possible. between the various ideal orientations which have been proposed. Another problem, not satisfactorily settled by earlier investigations. concerns surface textures in rolled metals. For instance, in rolled aluminum the surface texture in some cases appeared to be similar to the texture inside the sheet, whereas in other cases it was reported to be entirely different.' The conditions under which such differences may have arisen, and the possibility of the occurrence of different surface textures in other face-centered cubic metals do not appear to have been examined in detail. The present work was undertaken to investigate the above questions. Some of the results obtained have been described- riefly. Experimental Procedure Specimen Preparation: In the present investigation 2s aluminum, electrolytic tough-pitch copper, and commercial 70-30 brass were used. These materials were available in the form of cold-drawn rods. 1 in. diam for tough-pitch copper and commercial 70-30 brass and 11/2 in. diam for 2s aluminum. The cold-drawn bars were alternately annealed and rolled 30 pct lengthwise in several cycles until a penultimate thickness of 0.500 in. was reached. The intermediate and the penultimate anneals were carried out for 30 min at 380°C with 2s aluminum, and for 30 min at 550°C with 70-30 brass. For tough-pitch copper, the intermediate anneals were 30 min

Jan 1, 1953

By C. H. Samans, G. F. Tisinai

HARDENING and embrittlement of the ferritic chromium stainless steels at temperatures near 885 °F have been known for a long time.' However, no satisfactory explanation has been given. Both ordering and precipitation hardening have been suggested. Fisher, Dulis, and Carroll2 discovered a chromium-rich body-centered-cubic precipitate in embrittled alloys. Subsequently, Williams' and Wright4 also have found evidence of this body-centered-cubic constituent. William's hardness, electrical resistance, and magnetic studies led to his proposal of a new constitutional diagram for the Fe-Cr alloys. The new feature of this diagram is the eutec-toidal decomposition, below about 970°F, of the s phase into two stable body-centered-cubic solid solutions, one rich in iron and the other rich in chromium. An observation of Heger5 that the amount of s phase has increased and the amount of chromium-rich body-centered-cubic phase decreased in the interval 5000 to 32,600 hr at 900°F, even though the alloy increased in hardness, casts some doubt on this diagram. If precipitation hardening causes the embrittlement, the precipitate probably is always coherent with the matrix, since no evidence of overaging has been reported. It cannot be stated positively, however, that Fisher's body-centered-cubic constituent is the embrittling phase. According to Preston's data,6 such a chromium-rich phase should have a parameter less than about 0.5 pct larger than that of the iron-rich matrix lattice. Moreover, the constitutional relationships whereby Fisher's constituent forms, and whether it is stable, metastable, or a transition phase, are not yet completely clear. The recent studies of Wright4 and of Lommel,7 as well as the earlier studies of Becket8 and of Hochmann,9 have shown that 885°F hardening occurs in relatively pure Fe-Cr alloys. No evidence of its occurrence or absence in chromium itself has been reported. The rate of hardening in high purity alloys seems appreciably slower than that in alloys containing larger amounts of impurities (chiefly carbon and nitrogen). This may be due merely to the absence of hardening and straining effects from precipitated carbides and/or nitrides. These observations on high purity alloys make it seem unlikely that 885 °F hardening is caused by a constituent containing other than iron and chromium atoms, e.g., carbides and/or nitrides. Wright,4 Lommel,7 and Lena and Hawkes10 emonstrated the accelerating effects of a finely dispersed precipitate of (probably) chromium nitride on the hardening reaction. This appears to be evidence that lattice straining increases the rate of nucleation of the hardening constituent. Some new observations on 885°F hardening are reported here. They show an effect of preheat treatment that should contribute to a better understanding of the 885°F hardening phenomenon. They also clarify a discrepancy which exists in the literature. Some investigators have reported most rapid hardening at 885", whereas others have reported it at 930°F. The present work also shows that 885°F hardening does not occur in electrolytic chromium, and that any long range ordering type of reaction affecting any sizeable part of the volume is unlikely. Materials Studied Table I shows the currlposition of the alloys used in this investigation. In these alloys carbon and nitrogen are present in roughly similar amounts. Presumably both elements precipitate, as carbides and/or nitrides, during the heat treatments given.

Jan 1, 1958

By John Chipman

The concentration of a solute in a dilute ),zetallic solution may be measured by any of several parame- ters including weight percent, atom fraction, atom ratio, and lattice ratio. The ratio of filled to unfilled interstitial sites is useful for interstitial solutes. A variable 2 proportional to this ratio is used as a measuve of concentration. For component 2 irz a bitzary solution z2 = n2/Ym - nz/b) where b is the numberber of interstitial sites per lattice atom. For a t~lul-ticortzporzent solution this becomes zz = n2/(nl + Cvjnj) in which Vj = - l/b for an interstial solute and +1 for a substitulional solute. In the infinitely dilute solution the activity of an interstitial solute 2 is proportional lo z2. At finile concentration the departure from this limiting law is expressed us an activity coefficient, his coefficient is a function of concentra1io)z expressed as tevactiolz coeffcient 8; is analogous to the jark~iliar e£ bul is found to be independent of concentvation in certain solutions for which data are available. It is found that the same equations may be used to express the activity of a nonmetallic solute, sulfur, in liquid solutions of iron containing other solutes, both metallic and nonmetallic. For a nonmetallic solute or for one which strongly increases the actiuity of sulfur, it is convenient to assign arbitvarily a value vj = — 1. When this is done the derivative is found to be constant in each of the ternary solutions studied. The activity coefficient of sulfur in a complex liquid iron solution may be expressed as where nk is a second-order cross product determined in the quaternary solution Fe-S-j-k. The equation is used to calculate tlze activity of sulfur i)z three sevetl- component solutions. IN thermodynamic calculations concerning dilute solutions it is unnecessary to invoke laws and relations which extend across the concentration range to include concentrated solutions. In most binary metallic systems, as arkeen&apos; has recently pointed out, there exist two terminal composition regions of relatively simple behavior, connected by a central region of much greater complexity. When the solute is a nonmetal there is only one such region and in many systems the concentration range is extremely limited. It is the purpose of this paper to suggest a method for the calculation of activities in such a terminal region in which one or more solutes are dissolved in a single solvent of predominantly high concentration. HENRY&apos;S LAW In the usual textbook statement of Henry&apos;s law, concentration is stated in mole fraction. This has the advantage that it makes Henry&apos;s law thermodynamically consistent with Raoult&apos;s law. Since all measures of concentration at infinite dilution are related by simple proportion it follows that mole fraction, molality, atom ratio, weight percent, or any other unit of concentration can be used with the appropriate constant. At finite concentrations, however, calculations based on the law depend upon the unit employed. Deviations from Henry&apos;s law at finite concentrations depend upon the composition variable employed. They are evaluated in terms of activity and interaction coefficients2 which have become familiar features of metallurgical thermodynamics. It is the purpose of this paper to propose a measure of concentration for metallic solutions containing interstitial or nonmetallic solutes by means of which the calculation of activities in complex solutions may be simplified. The discussion will be restricted to free-energy interaction coefficients3 typified by Wagner&apos;s c|a BINARY SOLUTIONS The several measures of concentration which are to be considered are shown in line a of Table I. The corresponding activity coefficients are in line b and the deviation coefficients, sometimes called self-interaction coefficients, are in line c. Henry&apos;s law simply states that the activity coefficient approaches a constant value at infinite dilution. By adoptihg the infinitely dilute solution as the reference state and defining the "Henrian" activity as equal to the concentration in this state, the activity coefficient is always unity at infinite dilution. This convention is far sim~ler and more useful in dilute solution than emploiment of the &apos;Raoultian" activities and it will be used in the following discussion. The several definitions and equations of Table I will be referred to by means of their coordinates in the table. Early observations of deviations from Henry&apos;s law in metallic solutions were shown graphically4 rather than analytically. For the case of sulfur in liquid iron5 the slope of a plot of logfs vs (%S) was constant in the range 0 to 4.8 pct S, indicating constancy of eh2&apos; in Ic. He was proposed by wagnerz and has been widely adopted. The a function of IIIc recently employed by ~arkenl was designed specifically for dilute solutions. Darken has shown that the value of a12 remains essentially constant for many binary solutions within a substantial range of compositions. The atom ratio is directly proportional to the molalitv.<, a conventional measure of concentration. IVb and C served as the basis for smith&apos;s6 classic studies of

Jan 1, 1968

By K. Tangri, B. Swaroop

Simultaneous measurements of lattice (elastic) strain by X-ray line shift method and total strain with an electrical strain gage have been carried out on polycrystalli,ne nickel with the help of a specially designed tensometer attachment for the X-ray dif-fractometer. During the initial stages of deformation, the rate of increase in lattice strain closely follows the total strain until the plastic strain sets in. From then onwards, the two strains deviate from each other and with further increase in afiplied stress the rate of increase of lattice strain eventually decreases. Depending upon the mode of unloading, both compressive and tensile strains have been observed in nickel deformed up to 0.29 pct strain. These results have been explained on the basis of the effects of clustering of dislocations and also the production and behavior of point defects during loading and unloading, respectively. POLYCRYSTALS deformed plastically in a uniaxial tension test show residual lattice strains (hereafter referred to as RLS), which broaden the X-ray line profiles and shift their peak positions.&apos;&apos;4 It is known that uniform straining of a crystal lattice (macrostrain) produced movement of ddfraction line peaks, whereas nonuniform straining (microstrain) causes line broadening.= Though the nature and origin of RLS in deformed metals is not yet clearly understood, these are believed to be due to the presence of some form of a locked-up stress system. Several possible detailed interpretations6&apos;" of the stress system have been proposed by various workers and common to all these interpretations is the assumption that different parts of the aggregate have different tensile yield stresses; e.g., that a part A yields under a lower applied stress than a part B. Therefore, during the deformation process, the elastic strain in A will be less than that in B, and, after completion of deformation, B will tend to contract further than A but will be prevented from doing so by the restraining influence of A. Thus, when equilibrium is reached, A will be in compression while B is in tension. Although there is general agreement on the correctness of this argument, controversy still exists as to the exact nature of the parts A and B in a deformed metal. In an alternative approach to the creation of parts A and B, many other investigators have assumed that the RLS observed in unloaded specimens are in some way connected with the lack of proportionality between lattice strain and applied stress in the region above the yield stress." cullity13 has prepared a schematic summary of the results of previous workers, mainly Smith and Wood,2&apos;11 which suggests that, above the elastic limit, the lattice strain may increase less rapidly with respect to strain, or may even decrease with increase in applied stress. If the applied stress is then decreased, the lattice strain would decrease along a line parallel to the loading line in the elastic region and thus produce a compressive residual lattice strain after unloading. At equilibrium, to balance these compressive stresses? there would have to be regions under tensile stress which may well be the grain boundaries or the substructure walls formed during deformation. The present investigation was undertaken to gain a better understanding of the nature and origin of RLS and also to experimentally verify the salient features of this hypothesis. EXPERIMENTAL Stress and strain determinations were made with a specially constructed tensometer attachment for the X-ray diffractometer, Fig. 1: which permits the following measurements simultaneously on a sheet specimen under uniaxial tension at various stress levels during loading and unloading: a) lattice strains, E=. in a direction perpendicular to the direction of pulling (x direction) from shifts in X-ray line peak positions; b) the total strain, ex, in the direction of pulling. with the help of an electrical strain gage affixed to the back of the specimen directly below the area irradiated by X-rays: and c) the applied stress, with the help of a load cell which consisted of a calibrated stainless-steel sample of dimensions identical to those of the specimen under investigation, and to which it was coupled. Because of its high stacking fault energy.I4 nickel

Jan 1, 1970

By H. Conrad, V. V. Damiano, G. J. London

The slip mode activated during the c axis compression of single crystals of commercial-purity ingot SR beryllium, high-purity (twelve-zone-pass) beryllium, and Be-4.4 wt pct Cu and Be-5.2 wt pct Ni alloys in the temperature range of 25° to 364°C was determined using two-surface slip trace analysis, slip-step height analysis, and electron transmission microscopy. All three techniques indicated the occurrence of copious pyramidal {1 122) (1123) slip in the alloys over the entire temperature range, the amount increasing with temperature. Pyramidal slip was also indicated in the high-purity beryllium by slip trace analysis and electron transmission microscopy, but the amount was somewhat less than in the alloys. For the commercial-purity ingot crystals, only a very small number of pyramidal slip lines were observed, and these were in the immediate vicinity of the fracture surface. No pyramidal dislocations could be detected by electron transmission microscopy in this material. Dislocatransmissiontions with Burgers vectors [0001] and +(ll20) were identified by electron transmission microscopy inthe (1122) slip bands, as well as those with the j (1123) vector. This was interpreted to indicate that the edge components of the 3(1123) vector dislocations activated during c axis compression dissociate upon unloading according to the reaction i (1123) — [0001] + 3(1120) THE microstrain c axis compression of single crystals of commercial-purity ingot SR beryllium (99.6 pct), high-purity twelve-zone-pass beryllium (99.98 pct), Be-5.24 pct Ni and Be-4.37 pct Cu alloys was described in a previous paper.1 This paper covers in detail the analysis of slip traces observed on two mutually perpendicular lateral surfaces of these specimens, and a detailed description of transmission electron microscopy studies performed on foils cut from the bulk crystals after they had been deformed to fracture in the c axis compression. Observation of slip traces on single surfaces of deformed single crystals are generally insufficient to positively identify slip or twinning modes. The use of two carefully cut and oriented perpendicular surfaces can greatly aid in the positive identification and index- ing of slip traces, although even this technique may be quite inadequate if more than one type of slip system operates and if an insufficient number of traces are observed on the surfaces. The problem is greatly simplified for symmetric cases like that for c axis compression of an hep crystal such as beryllium, in which the operating slip systems are all equally inclined to the direction of the applied stress, and each slip system of a given slip mode has an equal chance of operating. For such cases, the traces of any given slip mode observed on the surfaces cut parallel to the c axis are symmetrically tilted about the c axis. It is therefore possible to quickly determine whether one or more slip modes are operating. Confirmatory evidence in support of the observations made on the external surfaces can be obtained from foils cut from the deformed crystals and examined by transmission electron microscopy. This latter technique serves to identify not only the operating slip plane but also the Burgers vector of the dislocations which participate in the slip. For this purpose, a simplified technique based upon a double tetrahedron notation is used in the present paper. The planes and directions in the hep lattice are all designated by letters rather than indices and extinction conditions are easily determined if the Burgers vector lies in the plane contributing to the diffraction. RESULTS 1) Slip Trace Analysis. The standard (0001) stereo-graphic projection of beryllium is shown in Fig. 1. The two mutually perpendicular, lateral surfaces of the compression specimen are represented by the diametrical planes AA&apos; and BB&apos;, also referred to as surface A and surface B. For the specific case represented (a Be-5.24 pct Ni specimen deformed by c axis compression at room temperature), the A surface is tilted 5 deg to the (10i0&apos;) plane and the B surface is tilted 5 deg to the (1120) plane. Two surface trace analyses may be facilitated by examining in turn the intersection of various great circle traces of specific pyramidal planes with two surfaces and comparing the angles made with the (0001) plane with those actually observed on the two surfaces. One then identifies the slip traces by trial and error on a best-fit basis. The (1122) type planes (it was found that slip occurred on these planes) are shown plotted on the stereographic projection in Fig. 1. One obtains directly the angles between the (0001) plane and the {1122) traces by measuring the angle from the periphery to the point of intersection along the lines

Jan 1, 1969

By V. F. Hollister

The Queen Charlotte gold deposit (also known as the Specogna, Babe, or Cinola) was discovered in late 1970 by Efrem Specogna and Johnny Trico. They were prospecting along the trace of the Sandspit fault, and they sampled jarositic material that included veins from the fault zone. Their assays included some good gold values. They located the Babe Claims in 1971 and optioned them to Kennco Explorations Ltd. Kennco conducted stream sediment and soil geochem studies, geological mapping and drilling of 55.2 m (181 ft) in two drill holes. Kennco withdrew from the property, and by 1977, Cominco, Placer Development, Silver Standard, and Quintana Minerals had each successively worked on the deposit. Consolidated Cinola Mines bought the claims in 1977 and completed exploration of the deposit ultimately in a joint venture arrangement with Energy Reserves. Energy Reserves entered in late 1979, and by 1983, a total of 200 surface and 12 underground drill holes had been completed, totaling 28 600 m (93,832 ft). In addition, a 461.9 m (1515 ft) adit was driven in the ore body. Reserves published by Cinola aggregate 34 Mt (37 million st) of 1.7 g (0.060 oz) Au per tonne. All industry geologists working in the area agree that the Queen Charlotte gold is an epithermal gold deposit in porous volcaniclastic and clastic rocks that is genetically related to a Miocene-Pliocene rhyolite plug. The geologic description here follows the oral presentation made by G. G. Richards, J. S. Christie, and M. R. Wolfhard at a 1976 CIM meeting. Additional comments by the late C. S. Ney of Kennco Explorations are included with the Richards, Christie, and Wolfhard data to complete the geologic set- ting. The attached reprint by Champigny and Sinclair (1 980) provides additional data on the deposit. The Queen Charlotte (Babe, Specogna, or Cinola) gold deposit is located on Graham Island in the northern Charlotte Islands, at the fault boundary of the Skidegate plateau and the Charlotte lowlands. The Sandspit fault marks the physiographic boundary, and it is intruded by rhyolite porphyry at the deposit. Because displaced geochem anomalies, drain- age patterns, and topography suggest dextral and east side down movement for the fault, exposed east block rocks are younger than rocks west of the fault. The east block, which included the ore deposit, is a lowland largely masked by unconsolidated Pleistocene and Recent clastic rocks. Rocks west of the rhyolite plug, on the Skidegate plateau, are Cretaceous carbonaceous and calcareous shale unconformably overlain by a thin veneer of rhyolite tuff. The deposit is about 100 m (328 ft) above sea level. GEOLOGIC SETTING At the ore deposit, the Sandspit fault is a complex structure. However, lithologies on either side of the fault-controlled rhyolite porphyry plug are distinct. West of the rhyolite, the upper member of the Cretaceous Haida formation shale is the most common rock type. The member is composed of dark grey to black, poorly consolidated, and thinly bedded carbonaceous and calcareous shale. The sequence is silicified to an argillite or a hornfels near the rhyolite. West of the rhyolite porphyry plug, but not importantly involved in the mineralization, is a thin masking cover of rhyolite tuff. The tuff unconformably succeeds the cretaceous shale, but it is largely eroded in the mine area. East of the fault-controlled rhyolite porphyry plug is a thick section of conglomerate and sandstone of the Miocene- Pliocene Skonun formation. The ore body occurs within the coarse clastics, the rhyolite intrusive as the western boundary. Ore is entirely contained within the clastics. Original permeability of the clastic rocks was a major control for ore deposition and alteration, and for that reason, the Skonun formation is described in greater detail. The Skonun formation clastics unconformably overlie Haida shale. The Skonun is at least 300 m (984 ft) thick in the mine area, where it trends northerly and dips easterly 15º to 25º. The sequence is about 62 percent conglomerate, 3 1 percent coarse arkosic sandstone, and 7 percent interbedded siltstone and sandstone. Contacts between adjacent beds are generally sharp. Stratigraphic correlations between drill

Jan 1, 1985

By L. R. Duncan, O. M. Wicken

Magnesium, the eighth most abundant element in the earth&apos;s crust, is found widely distributed in a variety of minerals. Among the more commercially important ones are magnesite (MgCO3), brucite (Mg[OH]2), dolomite (CaMg[C03]2), and the salts magnesium sulfate and chloride often found in natural brines. Among other commercially important magnesium-containing minerals are olivine ([MgFe]2Si04), talc (H2Mg3[Si03]4), and serpentine (H4Mg3Si2O9). These are valuable because of desirable characteristics given them by the magnesium content and its placement in the particular crystal structure. These minerals are the raw materials for a host of products including magnesium metal and several grades of magnesia or magnesia-containing materials for refractories, fluxes, fillers, insulation, cements, decolorants, fertilizers, and chemicals. Considering only those minerals valued for their magnesia or magnesium content, over 85% of the material tonnages are processed to be used as refractories. Dolomite, which is used in enormous tonnages for its physical properties in construction, has an important use as a refractory raw material in its own right and, after calcination, as a precipitant for magnesium hydroxide, which is an intermediate for the production of magnesia or magnesium metal. Magnesia from the reaction of calcined dolomite (or limestone) with seawater or magnesium-containing brines has supplanted much of the production of magnesia from mined magnesite, particularly in the United States. The best known of the minerals directly and widely exploited for magnesia content is magnesite, one of the calcite group of rhombohedral carbonates which includes calcite (CaC03), siderite (FeCO3), and rhodochrosite (MnCO3) among others. The members of this group enter into a wide range of substitutional solid solutions when the positive ions have similar radii. The radii of magnesium and iron ions are within 6% of each other; hence, magnesite and siderite form a complete series of which breunnerite (ferroan magnesite) is a well-known end member. However, the radius of calcium ion is 36% larger than that of magnesium ion, and only limited substitution exists at each end of the MgCO3-CaCO3 series. Dolomite is not a member of the calcite group, but results when calcium and magnesium ions alternate in equal number in an ordered structure among carbonate ions. The result of these relationships is that calcite and dolomite, often found intermixed with magnesite, occur commonly as identifiable crystal entities which can often be separated to a varying degree from the magnesite by various beneficiation techniques. Magnesite, when pure, contains 47.8% MgO and 52.2% CO.. The pure mineral is sometimes, but rarely, found as transparent crystals resembling calcite, but, preponderantly, magnesite contains variable amounts of the carbonates, oxides, and silicates of iron, calcium, manganese, and aluminum. Magnesite may be either crystalline or amorphous (cryptocrystalline). The crystalline form has a hardness of 3.5 to 4.0. The color may range from white to black with shades of yellow, blue, red, or gray. The color is not a fundamentally significant indicator of purity, but in a given deposit, an experienced person can often roughly grade magnesite by assessing color and crystallinity. The crystalline form of magnesite occurs in

Jan 1, 1983

By J. R. Hornaday, A. E. Morris, N. A. Parlee, D. C. Carmichael

Rates of absorption and effusion of hydrogen in solid iron were measurede by a Sieverts type of apparatus. With clean a iron these rates are diffusion controlled down to 420°C and are represented by the equation D = 6.70 x e-&apos;100&apos; crn2 sec-I Certain surface impurities can affect these rates at all temper-atuves. Thin oxide films lower, the apparent diffusivity of annealed iron markedly. Cold-worked iron (75 pct) annealed at 430°C has practically the same solubility and diffusivity as anealed iron. THE mechanism of absorption and evolution of hydrogen in solid iron alloys is not fully understood despite the large number of investigations on the subject. While there appear to be many instances of simple solid-state diffusion control of rate, there are many cases where investigators have either concluded that surface reactions are rate controlling or that some "nondiffusible" hydrogen resides in discontinuities. The purposes of this research were 1) to develop a sound method for studying this absorption and evolution behavior, 2) to examine it in pure annealed iron, and 3) to determine the effects of important variables, such as cold work, surface condition, and composition. This paper relates the progress toward these objectives. Much of the present knowledge of the movement of hydrogen through iron alloys comes from permeability studies which involve the measurement of the rate of passage (under steady state conditions) through membranes of the order of 1 mm in thickness. This method is open to question on various grounds. If surface reactions are involved, two different surfaces operating under two different conditions must be considered. The presence of defects in the membrane even of microscopic dimensions may lead to erroneous results. A few people have studied evolution of hydrogen into vacuum, under carefully controlled (unsteady state) conditions, and some of the best diffusivity data come from these sources. Most of these methods measure rates of evolution only and thus do not make a rigorous test for reversibility of behavior. It appeared that an "unsteady state" method that would permit the measurement of both rates of evolution and absorption under controlled temperature, pressure, and other conditions would offer several advantages. Accordingly the modified Sieverts apparatus described below was designed and built. APPARATUS This apparatus is shown in Fig. 1. The sample bulb is detailed in Fig. 2. Hydrogen of 99.5 pct purity and argon of 99.99 pct purity were used. The hydrogen was deoxidized and dried by means of a Deoxo unit followed by a "Dri-erite" tower. The argon was only dried. The gas burette was graduated in tenths of a cubic centimeter, and, with the aid of a travelling magnifier, readings could be estimated to the nearest 0.01 cc. The level of mercury in the burette was adjusted by means of a leveling bulb operated by a fine screw adjustment. An electrical system, consisting of two slightly separated platinum electrodes inserted in one leg of the manometer and a small light bulb was used to obtain rapid accurate adjustment of the pressure. The capillary tubing of the Vycor sample bulb was 3 mm bore as was all tubing back to the gas burette. The samples were discs made from vacuum-melted Ferrovac-E iron of greater than

Jan 1, 1961

By W. R. Wilcox

The camphor-anthracene system was chosen as a transparent low-melting analog of the zirconium carbide -graphite system. Camphor and zirconium car -bide both grow nonfaceted, while casting of mixtures yields platelets of both anthracene and graphite. Zone melting of thin layers of organic was observed under the microscope. Irregular lamellar structures were produced at high values of the ratio of the temperature gradient G to the zoning rate V. The anthracene invariably led the camphor, indicating lower kinetic undercooling for the anthracene. The lamellar spacing was an order of magnitude greater than typical spacings for metal eutectic systems. Exact behavior depended on orientation of the anthracene. Oriented dendritic structures were produced at low values of G/V. Transient and oscillatory behavior were also observed—much of it unexpected. A.RC-CAST refractory carbide-graphite mixtures are promising thermal-shock resistant materials. Oriented structures of these materials would be superior to arc-cast materials for many applications. Mollard and Flemings1 and Cline2 have shown that aligned structures can be obtained for a wide range of Pb-Sn alloys. However, these metals both solidify in a nonfaceted manner while graphite yields platelets or flakes. In addition only small diameter samples of Pb-Sn alloys were produced because it was necessary to avoid free convection and to have high temperature gradients. The purpose of the present work was twofold: 1) To observe the solidification of a transparent low-melting analog of carbide-graphite systems and 2) to see if larger diameter samples can be produced. EXPERIMENTAL PROCEDURE When zirconium carbide-graphite mixtures are cast, the resulting structure naturally depends on composition. Carbide-rich mixtures yield metal-like nonfaceted carbide dendrites in a eutectic matrix. Graphite-rich alloys have graphite platelets in a eutectic matrix. Empirically it was found that camphor-anthracene mixtures produce similar structures with camphor being nonfaceted and anthracene forming plates. The organic eutectic melted at 116°C and was composed of 78 wt pet camphor.3 The camphor used was U.S.P. grade from Fisher Scientific Company; the anthracene was 98+ pet fro Aldrich Chemical Co. The impurity content is judged to be on the order of 1 pet. Mixtures ranging from 50 to 88 wt pet camphor were employed for the experiments. All but one of the experiments were performed on the microscope-stage zone melting apparatus described in detail elsewhere.4 The organic mixtures were contained in horizontal cells made of microscope slides or cover glasses. In most of the cells the organic was present as a very thin layer, thus giving almost two-dimensional growth behavior. The cells were moved slowly under a heated wire, which caused a molten zone to move through the solid at rates ranging from 0.01 to 5.4 cm per hr. The temperature gradient was estimated before moving the zone by measuring the distance between the line where all solid was melted (freezing point) and that where solid first began to melt (eutectic temperature). The temperature gradient was found to be 465°C per cm in the thinnest cells used, which were made by pressing together two microscope cover slips in the organic melt and then rapidly withdrawing them. RESULTS The experimental results are described in four parts: simultaneous growth, dendritic growth, irregular growth, and transients and erratic phenomena. Steady state data are summarized in Fig. 1. Except where noted all comments are for the cells containing a thin layer of organic. A) Simultaneous Growth. Simultaneous and roughly parallel growth of anthracene and camphor was obtained over the full range of compositions investi-

Jan 1, 1970

By M. B. Bever, A. B. Michael

THE structure of cast A1-Si alloys is altered profoundly by modifying agents. Sodium, in particular, reduces the size of the silicon particles in the eutectic and tends to change their shapes from plates to nearly rounded grains. This refinement is accompanied by a shift of the eutectic to higher silicon concentrations and lower temperatures. Similar effects can be attained by rapid solidification. Hypotheses advanced to explain modification have involved the formation of a ternary eutectic,1 the removal of oxides by fluxing,&apos; and even a presumed allotropic transformation of silicon. Other hypotheses assume that the modifying agent causes an envelopment of the silicon particles by the aluminum-rich solid solution, but attribute this envelopment to different mechanisms. According to various explanations, the growth of the silicon particles is obstructed by an immiscible sodium-rich liquid," an adsorbed layer of sodium,&apos; or a ternary compound;5 his obstruction has been conceived as purely mechanical or as a colloidal action.&apos; It has also been proposed that sodium reduces the surface tension on the Al-Si interface, thus permitting the aluminum-rich solid to grow faster and to envelop the silicon particles.? Still other hypotheses stress undercooling and the attendant change in the rate of nucleation of silicon, but fail to ascribe any definite function to the sodium addition." &apos;" Procedure High-purity alloys of aluminum and 3 or 7 pct Si were treated with modifying agents containing radioactive sodium tracers. The experiments were intended to investigate the partition of sodium between the primary aluminum-rich solution and the eutectic, and, if possible, to determine whether sodium is concentrated in or around the silicon particles in the eutectic. Radioactive sodium fluoride, alone or mixed with stable sodium chloride, was allowed to react with the alloy for 5 min immediately before solidification in the crucible. Modification could not be attained with additions of less than the equivalent of approximately 0.1 pct Na. Some alloys were not completely modified, but comparison of the structures of treated and untreated specimens indicated a very considerable reduction in particle size of the silicon in all of the former. A treated alloy is shown in Fig. 1. Radioactive sodium fluoride was prepared by bombardment with deuterons having an energy of 14 mev. This bombardment (totaling, for example, 6 microampere-hours in one run) produced radioactive Na24 (half-life 14.8 hr) by the reaction 11Na23 (d,p) 11Na24. The radioisotopes of fluorine also produced have short half-lives and were not detected. A half-life determination by counting confirmed that the measured activity was due to Na24. The distribution of the sodium in the solidified alloys was determined by an autoradiographic technique by which a suitable stripping film is attached to a very thin metallographic specimen. After exposure and development, this emulsion remains superimposed on the specimen and may be examined microscopically or photographed by reflected light. The emulsion of the autoradiograph can be correlated directly with the underlying surface by simple adjustment in focus. The details of this technique have been described elsewhere." Results Fig. 2 is a micrograph of the autoradiographic emulsion ("autoradiograph") lying directly above the area of eutectic in Fig. 1. Fig. 3 shows a similar autoradiograph of a region consisting of primary solid solution. The small black dots (tracks) in these autoradiographs are developed grains in the emul-

Jan 1, 1954

By C. R. Fast, George C. Howard

Laboratory and field testing of various squeeze cementing techniques and materials revealed that many improvements could be made in squeeze cementing operations. The use of a slow-pumping squeeze cementing procedure permitted the control of the quantity of cement displaced into a formation and aided in obtaining a high final squeeze pressure. Field testing indicated the desirability of obtaining high final squeeze pressures, the need for improved formation breakdown fluids, and the necessity of controlling the pressure differential during testing after a squeeze job. INTRODUCTION During the past few years, squeeze cementing operations have been investigated, both from the theoretical as well as the practical point of view, in an effort to arrive at some solution to the many and varied problems that arise with this type of operation. A review of well files indicated that in many instances, wells were being squeeze cemented four and five times before a satisfactory pressure buildup was obtained. There seemed to be considerable variation in opinion as to the proper method of squeeze cementing, as well as disagreement as to the proper breakdown agent, the quantity of cement that should be used, type retainer and length of WOC* time that was necessary. Consequently, it was deemed advisable to approach this problem theoretically, field testing each idea developed in hopes of eventually arriving at a squeeze cementing procedure that would give reasonable assurance of a successful job after one squeeze cementing operation. This investigation was. therefore, divided into two broad headings: (1) Preliminary studies, which include both theoretical and laboratory studies, and (2) Field investigations to determine the proper squeeze cementing methods. PRELIMINARY STUDIES Overburden Pressure Studies Squeeze cementing problems are so intimately related to the earth&apos;s overburden pressure that solutions to them are very difficult, if not impossible, without an understanding of the nature and magnitude of the overburden pressures encountered at the depths of producing wells. It was thus felt that the first approach to research on squeeze cementing should be made through a study of these pressures. Since there has been rather loose usage of a number of the terms related to overburden preasure by different writers, the terms to be subsequently used are defined here. Theoretical overburden pressure is the calculated pressure at any given depth exerted by the theoretical weight of overlying formations as calculated from the average rock density. Fluid displacement pressure is that pressure at which fluid can be injected into a formation after it has been broken down. It may be more or less than the theoretical overburden pressure. Formation breakdown pressure is that pressure at which a formation parts or breaks and is usually thought of as fluid displacement pressure plus rock strength. Breakdown agent is that fluid with which the formation is fractured. The first step in the study of the earth&apos;s overburden pressures involved a review of pertinent technical literature. The general opinion expressed was that the overburden pressure gradient of the earth&apos;s formations is roughly 1.0 psi per foot of depth, and that application of sufficient pressure to stratified formations. will cause them to part at or parallel to the bedding planes. The second step in the study of overburden pressures involved a study of available well data in an effort to obtain some definite information as to the actual values experienced in the field for the above mentioned terms. Data from 115 cement squeeze jobs in the Gulf Coast area and 46 cement squeeze jobs and acid jobs in the West Texas-New Mexico area were closely analyzed. The analysis of these data showed that the average formation breakdown

Jan 1, 1950

By T. C. Russell

The Conda phosphate mine, eight miles north of Soda Springs in Caribou County, Idaho, was opened up by the Anaconda Copper Mining CO. in 1920. Except for brief periods, during the 20&apos;s and early 30&apos;s, the mine has maintained a continuous production, and 2,100,000 short tons of phosphate rock have been shipped to the company&apos;s phosphate fertilizer manufacturing plant at Anaconda, Mont., or to independent processing plants on the Pacific Coast; a small tonnage of the rock has been shipped to the Hawaiian Islands. The Phosphoria formation on the Conda property consists of two, commercial-grade phosphate beds separated by 147 ft of black to brownish colored phosphatic calcareous shales interbedded with softer mudstones, clays, and occasional narrow seams of oolitic phosphate. The main lower phosphate bed in the series averaging 7.1 ft in thickness, is called the "foot-wall bed," which lies coriformably on the Wells limestone formation, the 1atter often containing irregular bands of chert. The upper or " hanging-wall bed" of phosphate rock averaging 7.2 ft in thickness, is overlaid by thick quartzite beds, locally called the " Rex chert" member in the upper portion of the Phosphoria formation. (Fig 1.) There are two anticlines on the property with axis striking approximately parallel to the mountain range beneath which extensive development on phosphate rock has been conducted in the past, and is now in progress. The phosphate beds have been eroded to a large extent from the tops of these anticlines, leaving at least three well-pronounced outcrops of the phosphate beds exposed within the boundaries of the Anaconda Copper Mining Cornpany&apos;s properties. At present, mining operations in the Conda No. 3 mine are confined to the two phosphate beds along the east flank of the easternmost anticline, where the dips on the beds vary from 50° to 60° east, thereby affording favorable conditions for the sublevel mining system now in use. Mining operations formerly were confined to the footwall or lower oolitic phosphate bed because of its higher phosphate and vanadium contents (32 pct P²O5 and 0.29 pct V2 O 5); this bed averages 7.1 ft in thickness. The oolitic portions of the upper bed were of satisfactory grade, but the shale and clay partings (Fig 2) diluted the mined rock and could not he separated economically by selective mining or by sorting. Experiments in beneficiating this rock were carried on for a number of years. Recently, a simple washing process was adopted, which gave a satisfactory grade of concentrates and a high recovery of P² O5. In 1947 it was decided to expand Anaconda&apos;s production of treble superphosphate and phosphoric acid by approximately 90 pct. This rock will be obtained from the footwall and hanging-wall beds, and the rock from the hanging-wall bed will be benefici-ated at -Anaconda.l In order to take advantage of the previous development on the 500 secondary haulage level, short crosscuts will be driven at approximately 950 ft intervals from the existing lateral drifts through the hanging-wall shale beds. From the inner end of each crosscut, short lateral drifts will he driven in both directions, so that four working raises can he put up on the dip of the phosphate bed at proper intervals along each of the lateral drifts. The mining operation on the footwall bed at Conda

Jan 1, 1950

By K. K. Kershner, W. A. Calhoun, C. W. Funk

Future resources of aluminum may require the utilization of low grade ores to provide a more permanent protection for the nation. Aluminum minerals such as cloy, shale, and high iron laterites may become important sources. An evaluation of reserves is given. New laboratory results are reported on the Vereinigte desilication process. THIS report on future resources of aluminum metal emphasizes the necessity for investigating utilization of low grade potential ores to provide more permanent protection for the nation. Partial or complete interruption of the importation of high grade aluminum ores must be given consideration. Ultimately, aluminum minerals such as clay, shale, and high iron laterites may become the principal sources of aluminum. The development of extractive processes for treating these low grade materials is a step in long-range national preparedness that should receive more attention. In formulating such processes, the application of beneficiation methods for the purpose of classifying the several types of minerals before subjecting each type to the more expensive extractive procedures should be considered, and a careful survey of the basic factors of power sources, transportation facilities, and sources of raw material should be made. Domestic Bauxite Resources Of the domestic supply of current, treatable-grade bauxite, 95 pct comes from Arkansas. The present reserve of Arkansas bauxite suitable for metal production, including abrasive-grade, Bayer-grade, and modified Bayer-grade ores, is 34,000,000 tons. The total reserve of bauxite of all grades is approximately 75,000,000 tons. Reserves are estimated on a mined and dried basis. Data available to the Bureau of Mines in 1948 to 1949 were used in preparing Table I, which shows a breakdown by grades of bauxite for about a half of the reserves of the state. The modified Bayer ore, 10,555,500 long dry tons, is based on a cutoff of 8 to 15 pct silica. The sub- marginal 10,074,700 long dry tons is assumed to contain more than 40 pct gibbsite, more than 15 pct silica, and less than 32 pct available alumina. A considerable amount of this low grade material was consumed in 1949 and 1950. Additional tonnages of bauxitic and kaolinitic clays are indicated by the Bureau of Mines drilling project.&apos; Applying a 50 pct factor to arrive at long tons mined and dried, the results of this project are approximately 31,500,000 tons kaolinitic clay at +35 pct Al²O3 and 11,800,000 tons kaolinitic clay at 20 to 35 pct A1,0,. Total reserves of kaolinitic clays are probably quite extensive—several times the reserves shown in the Bureau&apos;s work. Total reserves of bauxitic and high iron clays from the drilling program and previously established figures are 63,980,000 tons. The mineral dressing methods,&apos; the lime-sinter process, he lime-sinter modification of the Pederson process," the lime-soda sinter process,"-&apos; and the Alcoa combination processa. have been described in the literature and will not be elaborated upon here. The less familiar Vereinigte Aluminium-Werke process used by the Germans during World War 11 may require some amplification. It was used to bene-ficiate boehmite ores containing 12 to 18 pct silica for a feed to the European Bayer process. Ore was

Jan 1, 1952