Search Documents

By Wm. Terry Siemers, Frank E. Kottlowski, George S. Austin

The value of industrial rocks and minerals produced in New Mexico in 1978 exceeded $227 million. The state ranked first in the nation in production of potash and perlite and was a leader in pumice production. Other commodities with sizable production in New Mexico include barite, caliche, clay, dimension stone, fuorspar, gypsum, humate, limestone, mica, salt, sand and gravel, scoria, and silica sand. Non-metallic resources are distributed throughout the state, but development and exploitation is concentrated in western and southeastern New Mexico. The value of industrial rocks and minerals within the state grew about 9% to more than $227 million in 1978. Continued growth, however, depends on continued demand, exploration, and development.

Jan 1, 1982

By W. P. Sykes

IN an earlier paper1 the composition-temperature limits of the gamma iron phase in the iron-tungsten system were reported as approximated Fig. I.-DIAGRAM OF ALPHA-GAMMA LOOP AS DETERMINED BY MICROSTRUCTURE AND THERMAL ANALYSIS. by thermal analyses. At that time no attempt was made to develop metallographic evidence of the coexistence of two phases in the iron-rich solid solution at temperatures between 900° C. and 1400° C.

Jan 1, 1931

By K. Thirumalai

Rock response to heating depends on properties of rock material and varies widely between different rock types. By dissipating energy, surface melting limits rapid heating and fragmentation of rocks achieved by surface heating methods. This study advances a concept of rock fragmentation by rapid internal heating of a localized inner volume of rock. The working of the method to achieve fragmentation of rocks (Charcoal granite and Dresser basalt) having poor response to surface heating is analyzed. Experimental data on elevated temperature rock properties required for the study are presented. Based on the properties of test rocks, a high frequency (50 MHz) dielectric heating method of generating localized internal heating was selected for experimental study. The test rocks were fragmented without melting under localized heating below 600ºC. The heated volume required for fragmentation was observed to be less than 2 percent of the test block volume. A practical application of the method for in situ fragmentation of rocks is suggested.

Jan 1, 1971

By William Daly

THE application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable.

Jan 1, 1934

By Charles H. Eldridge, Robert J. Anderson

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By H. J. Rose

Graphic methods have long been used to advantage in dealing with diverse phases of fuel technology and research. Not only are graphs convenient for presenting data and making calculations, but they are invaluable for deriving generalizations from a mass of data. This is particularly true when relationships are obscure and numerical correlation is poor. This paper describes a new form of graph, the Multibasic Coal Chart, which has been developed to facilitate the study and comparison of coals of all ranks from peat to anthracite on any moisture and purity basis. This type of chart is of unique value for coal classification purposes, since it permits a direct visual comparison of the results obtained when coals are classified by the various systems which have been proposed. Coals are highly variable in character as a result of wide differenees in original vegetal ingredients, degree of metamorphism, and nature and amount of associated impurities. For nearly 100 years, attempts have been made to devise a satisfactory method of classification, and many tables, formulas, ratios and graphs have been suggested. Many of the suggested systems possess considerable merit and have found a limited use, thus promoting a better understanding of coal. However, objections have been raised against each system, and none has received general adoption. When the various systems of classification are compared, it is found that there is an apparently almost hopeless confusion due to: 1. Serious lack of agreement as to the proper moisture and purity basis on which to classify coal. More than ten different bases have been proposed, each of which requires complete recalculat.ion of the analysis data used. 2. Lack of agreement as to what chemical and physical properties are most important and best to use for classification purposes. There is too little knowledge of the degree to which these properties can be correlated.

Jan 1, 1930

By Robert J. Anderson, Charles H. Eldridge

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By Joseph E. Pogue

Proration in the petroleum industry has come to mean a method for curtailing the production of crude petroleum by artificial effort, and it is in this sense that the term is employed throughout this paper. Although a contrived curb on supply has been invoked at various times in the past in particular fields and to meet specific situations, it is not until the past few years that this procedure has become general and assumed a dominant role in the oil business. In the sense that we now understand it, proration had its inception in the Seminole area of Oklahoma in 1927, from which time and place the practice spread to include practically all the flush oil fields of the country, especially those of California, Kansas, Oklahoma and Texas. At present there is perhaps no phase of the oil business that commands more attention than proration, nor one that engages more time and effort on the part of executives in the business. The practice of proration, indeed, has not only become an integral part of the policy of most companies and operators, but it has also taken on the aspects of a "movement" involving two schools of thought with considerable feeling, and at times some bitterness, on both sides. In this atmosphere it is difficult to find calm, dispassionate consideration of proration, for most discussions are either vigorous exhortations by its proponents, or else sharp condemnations by its opponents; although it appears that the majority of the industry is clearly "in favor of" proration. It is hoped that this analysis will be taken as an attempt to appraise the movement as an economic force, without bias and without regard to the incidence of the conclusions upon any preconceptions that the industry may entertain. Evolution of Proration To appreciate the causes that brought proration into being, it is necessary to view briefly the development of the petroleum industry over the past twenty years, approximately the span of the gasoline era., For the first ten years of the period, the industry was seeking capital

Jan 1, 1932

By Frederic P. Dewey

It is common to blame irregular assay results upon volatilization and much has been written upon the subject, but there is no real evidence that, in a properly conducted assay, the loss of either gold or silver by volatilization is sufficient to affect appreciably the result, even when arsenic or antimony may be present. Bulk assays of flue dust from assay muffles have been published, but the data given are totally insufficient to even approximate the volatilization from a single assay; and such figures as we have indicate the volatilization to be extremely small. Diligent search in the literature and wide inquiry among assayers and instructors have failed to produce a single case where the litharge volatilized in making an assay has been collected and assayed for gold and silver. Having attempted to do this, with most indifferent success, I am not surprised that this has not been done. While various textbooks give volatilization as a cause of loss in cupella-tion, it may safely be said that in the rare cases where this volatilization is sufficient to affect appreciably the result it is due to excessive temperature. Percy' says "The loss of silver by volatilization during cupellation is very slight (unless the temperature has been much too high), and may be disregarded." This statement is repeated by the Beringers2 and Smith,3 who includes gold with silver. Mitchell4 says the litharge fume rarely contains over one ten-thousandth of silver. Campredon5 ays that at a proper temperature no silver is lost by volatilization. Primarily, excessive temperature may be due to too high general temperature in the muffle; but it may often be due to temperature localized within the bead by oxidation of the metals and this may be influenced by other causes than the general temperature. I have shown an ex-

Jan 1, 1921

By W. J. Heck

The need for a better understanding of the effect of fluid pressure on the strength of intact and jointed rock has long been recognized. The behavior of pore fluid pressure was first pointed out by Terzaghi 1 who suggested the application of the effective stress concept to rock and concrete. While the effective stress concept has been used for some time in the design of mass concrete dams, it only recently has been applied to rock. Robinson 2 and Handin et al.3 evaluated the effects of pore pressure on a variety of sedimentary rocks and demonstrated the validity of the concept. Work using pore fluids other than water has been done by Boozer, et al.4 who considered strain rate and temperature as additional variables. According to the effective stress theory, the effective stress, [a], is the difference between the total stress, [a], and the pore pressure, u, and is the controlling factor influencing frictional strength of rock, other parameters remaining constant. Assuming the Mohr-Coulomb failure criteria applies, the shear strength, T, is given by the equation [r=d+ (a-u)tan ¢](1) where [~F], the angle of internal friction, and c, the cohesion intercept of "no load" shear strength, are the effective stress parameters.* Robinson,2 Handin,3 and others have demonstrated that moderately porous sand-

Jan 1, 1972

By D. Silverman, A. R. Brown

EquipmENT and methods for locating the points of entry of salt water into oil wells are described. These techniques make it possible to delineate accurately the top and bottom boundaries of water zones whether bottom water or intermediate zones of production, Data are given on tests by this survey method on a number of producing wells, Complete results were obtained on wells shelving water percentages ranging from high values to as Little as 10 pct salt water. A number of the wells tested were plugged back and the results are reported in detail. While not all the work-overs were successful, evidence, including the results of reruns by this survey method, points to failure of the plugback operations. The data provided in the tests discussed show, contrary to general opinion, that a large percentage approaching 50 pct of the wells showed intermediate water instead of bottom water. Furthermore, approximately a third of the wells tested showed multiple zones of water production. The equipment comprises a long pipelike assembly carrying 10 pairs of electrodes spaced apart a distance of 4 ft. A surface-controlled solenoid-operated switch is provided to connect each of the individual pairs of electrodes in turn to a single-conductor steel-armored cable by means of which the conductivity of the fluid in the vicinity of each of the electrode pairs can be continuously recorded at the surface. Any number of electrode pairs and any spacing can be used. This assembly is lowered on tubing and placed in position opposite the section of the well to be studied. A conventional rod pump is used to produce the well for the survey. The pump inlet is placed below the lowest electrode pair. The well is conditioned by pumping Out the salt water normally standing in the well and introducing fresh water into the annulus at the surface. When the resistivity of the water standing in the well has been increased to a sufficiently high value, the inflowing fresh water is stopped and the drawdown operation of the survey is started. As the fluid head is lowered by pumping, fluids flow into the well and the entry Of salt water is indicated by the change in resistivity of the fresh water opposite the 'Ones Of water entry, The process can be repeated as Often as necessary with little effort and without moving any well equipment to be sure that the fluids produced from each zone are representative Of the true reservoir content. Introduction The oil industry has been concerned from its inception with the control of fluids entering its wells. In order to effect the greatest economy of operation and to get the greatest total production of petroleum liquids out of the ground, the flow of gas and water must be controlled and often extensive workovers are planned and carried Out for this purpose. This has become even more important in recent Years because of the need for the conservation of natural resources. Whereas producing operations concerned with the original completion of a well are assisted to a great extent by a wide variety of instruments developed and perfected for that purpose, workover operations on oil wells have been greatly hindered by a lack of suitable instrumentation. The industry has searched for many years for a satisfactory instrument and process that

Jan 1, 1948

By J. R. Long, E. T. Hayes, D. C. Root, R. S. Dean

THE U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities' and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriate applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately applicable. While atomic hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-arc methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1946

By A. R. Brown, D. Silverman

EquipmENT and methods for locating the points of entry of salt water into oil wells are described. These techniques make it possible to delineate accurately the top and bottom boundaries of water zones whether bottom water or intermediate zones of production, Data are given on tests by this survey method on a number of producing wells, Complete results were obtained on wells shelving water percentages ranging from high values to as Little as 10 pct salt water. A number of the wells tested were plugged back and the results are reported in detail. While not all the work-overs were successful, evidence, including the results of reruns by this survey method, points to failure of the plugback operations. The data provided in the tests discussed show, contrary to general opinion, that a large percentage approaching 50 pct of the wells showed intermediate water instead of bottom water. Furthermore, approximately a third of the wells tested showed multiple zones of water production. The equipment comprises a long pipelike assembly carrying 10 pairs of electrodes spaced apart a distance of 4 ft. A surface-controlled solenoid-operated switch is provided to connect each of the individual pairs of electrodes in turn to a single-conductor steel-armored cable by means of which the conductivity of the fluid in the vicinity of each of the electrode pairs can be continuously recorded at the surface. Any number of electrode pairs and any spacing can be used. This assembly is lowered on tubing and placed in position opposite the section of the well to be studied. A conventional rod pump is used to produce the well for the survey. The pump inlet is placed below the lowest electrode pair. The well is conditioned by pumping Out the salt water normally standing in the well and introducing fresh water into the annulus at the surface. When the resistivity of the water standing in the well has been increased to a sufficiently high value, the inflowing fresh water is stopped and the drawdown operation of the survey is started. As the fluid head is lowered by pumping, fluids flow into the well and the entry Of salt water is indicated by the change in resistivity of the fresh water opposite the 'Ones Of water entry, The process can be repeated as Often as necessary with little effort and without moving any well equipment to be sure that the fluids produced from each zone are representative Of the true reservoir content. Introduction The oil industry has been concerned from its inception with the control of fluids entering its wells. In order to effect the greatest economy of operation and to get the greatest total production of petroleum liquids out of the ground, the flow of gas and water must be controlled and often extensive workovers are planned and carried Out for this purpose. This has become even more important in recent Years because of the need for the conservation of natural resources. Whereas producing operations concerned with the original completion of a well are assisted to a great extent by a wide variety of instruments developed and perfected for that purpose, workover operations on oil wells have been greatly hindered by a lack of suitable instrumentation. The industry has searched for many years for a satisfactory instrument and process that

Jan 1, 1948

By F. V. Shallcross

Physical properties of thin films of CdS and CdSe formed by vacuum deposition onto glass sibstrates have been studied as a function of deposition and processing conditions. The crystallinity and surface features of CdS films were examined using electron microscopy and electron and X-ray diffraction techniques. The films were poly crystalline; the preferred orientation and crystallite size increased with film thickness, substrate temperature, and deposition time. The CdS films consisted primarily of hexagonal-phase material, in contrast to similarly prepared CdSe films which have previously been observed to contain mixtures of cubic and hexagonal phases. As-deposited CdS films showed no major dependence of Hall mobility on crystallite size or degree of preferred orientation. Hall mobility and carrier concentration in CdS and CdSe .films were measured at various temperatures; both parameters increased with temperature and yielded activation energies which depended on fabrication conditions. Surface-desorption phenomena and overcoating of the semiconductor with SiO affected the observed electrical properties significantly. THIN films of cadmium sulfide1,2 and cadmium sele-nide3,4 have been employed by various workers as semiconductors in the insulated-gate thin-film field-effect transistor, known as the TFT. These devices are most commonly made by vacuum deposition of all materials onto an amorphous substrate such as glass. A knowledge of the microstructure and electrical properties of semiconductor layers used in the thin-film transistor is essential in order to form a realistic model for the device and to improve its performance, reproducibility, and reliability. This paper will describe studies of the physical properties of vacuum-deposited CdS and CdSe films prepared under various conditions. Structural characteristics examined in- cluded phases present, crystallite size, nature of preferred orientation of crystallites, surface roughness, and structural homogeneity throughout the film thickness. Electrical properties measured were Hall mobility and conductivity and their dependence on temperature and ambient. Thin-film properties are affected by many fabrication parameters including purity and physical form of evaporant, deposition rate, film thickness, design and temperature of the evaporation crucible, geometry of the deposition chamber, nature of the residual atmosphere, composition and temperature of the substrate, and details of postdeposition processing. PREPARATION OF FILMS In this work the semiconductor films were deposited in a conventional oil-diffusion-pumped system with pressures in the 10-8 torr range. The CdS evaporant was obtained from the Eagle-Picher Co. as a high-purity coarse-grained crystalline powder; the CdSe was a high-purity sintered powder supplied by the Harshaw Chemical Co. The evaporation crucible was a resistance-heated molybdenum-wire basket coated with aluminum oxide and filled with a quartz wool plug at the top. The source to substrate distance was usually 10 cm. This region was enclosed by a Pyrex inner cylinder. The substrate was heated with an overlying Pyrex plate coated with tin oxide. The substrate temperature was controlled using a thermocouple attached to the lower side of the heater. This thermocouple was calibrated against another thermocouple attached to a dummy substrate and by observation of melting points of various metal films deposited in the system. The substrates were polished borosilicate glass plates and conventional glass microscope slides. Substrate preparation included cleaning with an ultrasonically agitated detergent bath followed by isopropanol-vapor de-greasing. Film thickness was measured interferomet-rically during and after deposition. STRUCTURE OF CdS FILMS Structural studies were performed on CdS films using electron diffraction, electron microscopy, and

Jan 1, 1967

By S. Yamaguchi

IN this study of thorium and uranium minerals an x-ray shadow microscope of the Cosslett type1 was used. A flux of electrons driven with a voltage

Jan 1, 1959

By Frank G. Miller

The lower cost of producing oil from naturally flowing wells compared with pro-luction costs accruing from artificial lifting methods has stimulated much research, rith the joint purpose of extending the natural flowing life of wells and of increas-ng the productivity of small wells. The iboratory investigation described herein was made to determine the effect of a lotted liner on the pressure gradient in the icinity of the wall of a flowing well. Flow estrictions caused by the liner induce nergy losses between the oil-bearing for-lation and the inside of the liner, which lay be reduced by improved liner design, nd thereby the flow capacity of wells may e increased. These losses have been evalu-ted for rectangular slots of different sizes, nd means are suggested for reducing them. The dearth of information concerning the ature of the flow of fluids from uncon-slidated sands through small openings in he walls of. pipes—as represented by the ow of oil from an oil sand into a slotted ner—is acknowledged. Although the bene-ts to be realized by operators through the se of optimum liners is just beginning to e recognized generally, Coberlyl in 1937 ointed out that the functioning of screen is is an important factor in the pro-uction of oil. From his study on the :lection of size of oil strings for wells in California, Parks2 concluded, in part, that the perforated section of the oil string deserves continued study, especially with respect to the selection of perforations. The growing use of gravel packing resulting from certain research findings lends even more significance to the problem of selecting optimum liners, as the application of these methods usually requires slotted liners or other kinds of perforated liners. The present study was made to obtain further information for the guidance of engineers and operators in selecting slotted liners and to develop a laboratory method that may be used in analyzing possible pressure conditions surrounding most types of perforated casings used in producing oil wells, so that the present inadequate fund of knowledge on this important subject may be expanded. Discussion of ProbleM At the beginning of the investigation the following assumptions were made regarding bottom-hole conditions of a producing oil well and the oil-sand reservoir it penetrates: (I) Conditions of steady-state flow exist, (') a a homogeneous liquid is being produced) (3) no contaminating material (such as drilling fluid) is present between the liner and the face of the oil-bearing sand, (4) the well is vertical and completely penetrates a horizontal sand stratum of uniform thickness occurring between two impermeable strata, and (5) the flow is wholly viscous. If the foregoing assumptions are made, with the added requirements that the sand

Jan 1, 1941

By V. H. Wilhelm

The year 1941 in the California oil industry was marked by an increased market demand, drilling activity, and production of crude oil. Although seven new oil fields and two gas fields were discovered during the year, additions to reserves from these discoveries, as well as extensions and revaluations of previous discoveries, were approximately 100 million barrels, as against estimated withdrawals of 230,233,000 barrels. The year was remarkable for the very great increase in domestic demand for all products, which more than compensated for the loss in shipments to Japan, which averaged 60,041 bbl. Per day during 1940. Demand in terms of crude during 1941 was 648,967 bbl. per day as against 632,647 for the same period in 1940. This abnormal increase in demand is due to increased industrial activity, and especially increased railroad activity. Gasoline consumption for 1941 was 241,011 bbl. per day as against 217,744 in 1940. Demand for fuel oil increased from 259,806 bbl. per day in 1940 to 285,896 in 1941, and caused a withdrawal from stocks of more than 7,473,000 barrels. During 1941, total oil storage declined 9,153,000 bbl., but additions to storage of 1,754,000 bbl. of light oil and light oil products were offset by a withdrawal of 10,907,000 bbl. of heavier products. Production during the year is estimated at 230,233,000 bbl. as against 222,784,386 bbl. for 1940. TraNsportation For a short time, California was affected by lack of transportation due to the diversion of tankers. This shortage affected the movement of oil from the Sari Joaquin mated to the refineries, since a large percentage of this production is moved to the coast through pipe lines, and thence by tankers to Los Angeles and San Fran-,iSco, Return of the tanker fleet, which may be temporary, indicates that there is a possibility of ample supplies of petroleum products in the Pacific Northwest. Drilling Activity Contrary to general opinion, drilling activity increased in 1941 over the pre-vious Year, 942 wells being completed in 1941 as against 890 in 1940, an increase Of 6 per cent. This increase was due to the increased demands for fuel oil, and also to the decreased drilling costs, which made many former marginal locations economic. The main activity caused by increased demands for fuel oil was in the Mt. Poso, McKittrick, Midway and Santa Maria Valley oil fields. Dry-hole footage in 1941 was 655,354 ft. as against 583,537 ft. for 1940. Curtailment Voluntary curtailment succeeded in holding production considerably below demand, although it was above the state quota. During the year the top allotment

Jan 1, 1942

By Hugh S. Spence

The use of natural feldspathic rocks, as opposed to straight feldspar, for ceramic purposes is not new. "Cornwall stone," a semi-kaolinized granite containing fluorite, has long been used by the English pottery trade instead of feldspar, and "Carolina stone," a similar rock, is now being offered to the American trade. A recent report of the U. S. Bureau of Mines states that trachyte, a glassy volcanic rock, is being used in California instead of feldspar in ceramic bodies. In Germany, phonolite and basalt have been investigated, and possibly also used, as ceramic raw materials, and extensive research has been conducted in Russia in recent years looking to the utilization of the immense bodies of nepheline syenite of the Kola Peninsula, which is the host rock of the apatite deposits now being exploited on a large scale in the Murmansk region; the nepheline is recovered as a by-product of the concentration of the apatite. Long used principally as a raw material for the pottery and allied industries, where, in bodies, glazes, enamels, etc., it serves as a fluxing ingredient and forms, on firing, a glassy bond with the more refractory clay, flint and coloring particles, feldspar has been finding ever increasing employment in glass. In 1936, over half of the nearly quarter of a million tons of feldspar sold in the United States went to the glass trade. Its usefulness for this purpose is due to the resistance to thermal shock which it imparts to glass products, particularly bottles, containers and tableware, because of its alumina content, which averages from 16 to 20 per cent. Active search has been wade on the American continent during the past few years for other minerals of feldspathoid type, with comparable or higher alumina content, that, may be suitable for glass and other ceramic purposes. One of the most important results of this work has been the delimiting in central Ontario of large bodies of nepheline syenite of excellent, ceramic grade.

Jan 1, 1942

By V. H. Wilhelm

The year 1941 in the California oil industry was marked by an increased market demand, drilling activity, and production of crude oil. Although seven new oil fields and two gas fields were discovered during the year, additions to reserves from these discoveries, as well as extensions and revaluations of previous discoveries, were approximately 100 million barrels, as against estimated withdrawals of 230,233,000 barrels. The year was remarkable for the very great increase in domestic demand for all products, which more than compensated for the loss in shipments to Japan, which averaged 60,041 bbl. Per day during 1940. Demand in terms of crude during 1941 was 648,967 bbl. per day as against 632,647 for the same period in 1940. This abnormal increase in demand is due to increased industrial activity, and especially increased railroad activity. Gasoline consumption for 1941 was 241,011 bbl. per day as against 217,744 in 1940. Demand for fuel oil increased from 259,806 bbl. per day in 1940 to 285,896 in 1941, and caused a withdrawal from stocks of more than 7,473,000 barrels. During 1941, total oil storage declined 9,153,000 bbl., but additions to storage of 1,754,000 bbl. of light oil and light oil products were offset by a withdrawal of 10,907,000 bbl. of heavier products. Production during the year is estimated at 230,233,000 bbl. as against 222,784,386 bbl. for 1940. TraNsportation For a short time, California was affected by lack of transportation due to the diversion of tankers. This shortage affected the movement of oil from the Sari Joaquin mated to the refineries, since a large percentage of this production is moved to the coast through pipe lines, and thence by tankers to Los Angeles and San Fran-,iSco, Return of the tanker fleet, which may be temporary, indicates that there is a possibility of ample supplies of petroleum products in the Pacific Northwest. Drilling Activity Contrary to general opinion, drilling activity increased in 1941 over the pre-vious Year, 942 wells being completed in 1941 as against 890 in 1940, an increase Of 6 per cent. This increase was due to the increased demands for fuel oil, and also to the decreased drilling costs, which made many former marginal locations economic. The main activity caused by increased demands for fuel oil was in the Mt. Poso, McKittrick, Midway and Santa Maria Valley oil fields. Dry-hole footage in 1941 was 655,354 ft. as against 583,537 ft. for 1940. Curtailment Voluntary curtailment succeeded in holding production considerably below demand, although it was above the state quota. During the year the top allotment

Jan 1, 1942

By Mark J. Klein

The precipitation of nitrogen in quenched and aged CY-35 at. pct Re was followed by internal-friction and electrical-resistivity measurements. It is shown that the precipitation kinetics of nitrogen from solution are many orders of magnitude lower in this alloy than in chromium. The reluctance of nitrogen to precipitate from sol~ction can be attributed to the composilional r-eadjustnzents required in the z.icinity of a chromium nitrade particle for gowth to occur. AS part of an investigation of the mechanism by which rhenium increases the low-temperature ductility of chromium and other Group VI-A metals, it was of interest to compare the concentration of interstitial elements retained in solution in chromium with that of a ductile Cr-Re alloy. The presence of certain interstitial elements in chromium has been shown to decrease its ductility1-5 and, of these interstitials, nitrogen is believed to have the most detrimental effect on mechanical properties. Thus, a comparison of the disposition of nitrogen in chromium with that in a ductile Cr-Re alloy might provide information about the mechanism whereby rhenium enhances the ductility of chromium. In previous internal-friction studies it was shown that the equilibrium solubilities of nitrogen in chromium and Cr-35 at. pct Re did not differ greatly.= However, results indicated that the actual concentration of nitrogen retained in solution at ambient temperatures is likely to be considerably greater in the alloy than in chromium because the precipitation kinetics of nitrogen are greatly retarded by the addition of rhenium. The objective of this investigation was to study the kinetics of nitrogen precipitation in Cr-35 at. pct Re in greater detail and to obtain information concerning the mechanism of nitrogen precipitation in this alloy. The properties studied were internal friction and

Jan 1, 1967