Search Documents

By James K. Gluck, William E. Galloway, Gary E. Smith, John P. Morton, Christopher D. Henry

INTRODUCTION Surface mining and in situ leaching of uranium have the potential to alter ground-water quality around mines and leach sites. Of particular concern is the fate of uranium and its associated trace elements: molybdenum, arsenic, and selenium. We wish to under- stand the natural processes that control trace element concentrations in ground water and how these processes will influence dispersion of the elements from a mineralized zone, both naturally and during and after mining or restoration. For example, it is commonly recognized that the trace elements are soluble in oxidizing ground water but are insoluble, and can be precipitated, in reducing ground water. Thus oxidizing, metal-bearing water leaving a deposit could re- enter reduced ground, causing the water to be re- reduced and the trace elements to be, reprecipitated. In a sense, this is recreating the original mineralization process. To accomplish the above goals, we have (1) examined the theoretical controls of concentrations based on the available geochemical and thermodynamic data, (2) determined the major ion composition and oxidation-reduction status of Oakville waters because of the influence of these factors on trace element solubility, and (3) determined trace element concentrations and distribution in Oakville ground water. The last approach is used to evaluate how well actual behavior follows predicted behavior. This report focuses on two elements, uranium and molybdenum, because they exemplify the results obtained. The report also is restricted to a regional study of Oakville ground water. Results of more de- tailed study in and around major uranium districts in the Oakville and much of the raw data that support the conclusions in this report are presented in Galloway, Henry and Smith (1980). This report is part of that larger study, which concerned the depositional systems, hydrology, and geochemistry of the Oakville. The U.S. Environmental Protection Agency funded the study, under grant numbers R-805357-01 and R-805357-02. Theoretical controls were determined by reviewing the available literature on aqueous chemistry and behavior of uranium and molybdenum. To aid in under- standing water chemistry, Oakville water analyses were run through a modified version of the computer model WATEQF (Plumer, Jones, and Truesdell, 1976). WATEQF calculates speciation of dissolved ions and determines saturation with respect to a variety of minerals. In the discussion below, ion activity products (IAP) are compared with the equilibrium constant (KT) for various reactions and mineral products. Values of log IAP/KT near zero indicate that the water is in equilibrium with a mineral. Values less than -1 indicate considerable undersaturation and values greater than +1 indicate oversaturation. Galloway, Henry, and Smith (1980) give a more complete discussion of the application of this approach to Oakville water chemistry. Eh-pH diagrams have been constructed or adapted from the literature to predict what form -- dissolved ion or stable mineral species -- uranium and molybdenum assume under various conditions. Construction of the diagrams has followed procedures described by Garrels and Christ (1965). This approach is particularly appropriate because the solubility of the elements is Eh-dependent, and Eh varies greatly within the Oakville aquifer. A number of assumptions or approximations are inherent in the use of Eh-pH diagrams and chemical models such as WATEQF and in the interpretation of water chemistry in general. Both Eh-pH diagrams and chemical modeling rely entirely upon available thermo- dynamic data, including free energies of formation and dissociation constants for various reactions. These values are known to varying degrees of accuracy. Most major ions and minerals are relatively well control- led; however, data for trace metals are much poorer. Thermodynamic data are not available for some minerals, and for other minerals, two or more divergent values exist. By necessity, we have relied on the judgment of others to evaluate thermodynamic data. Calculations by WATEQF and constructions of Eh-pH diagrams are based on an assumption of equi1ibrium. Equilibrium may not be comnon in low-temperature aqueous environments; at best, ground-water composi tion may be in a state of dynamic equilibrium, continuously changing due to changes in environmental conditions. Eh-pH diagrams show what phases are stable at equilibrium under given conditions; they do not prove that the phases actually exist. Many minerals persist or form metastably under conditions outside their equilibrium stability field. The kinetics of reactions, which cannot be evaluated here, are important in determining what phases occur. Kinetics may be less of a problem for ground water that travels and evolves slowly through a semihomogeneous matrix than for many other natural systems. Eh-pH diagrams show equilibrium fields only of phases included. They do not indicate anything about stability relative to phases not included in the diagram. WATEQF, obviously, cannot calculate the degree of saturation of a mineral not included in the program or for which the appropriate ions were not analyzed. Thus, a mineral that was not considered may be the most stable phase under a given set of conditions and may control the solubility of a trace element. Also, this study is limited exclusively to in- organic compounds. Organic material is known to be an

Jan 1, 1980

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion-equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control. For the present purpose a number of factors important to efficient heat liberation and recovery have been grouped as follows: 1—combustion, temperatures, and rates of heat liberation; 2—radiation, convection, and furnace and boiler configuration; 3—sponge ash, slag, and hard-bonded deposits; 4— low-temperature deposits and corrosion (cooling flue gas below dew point and air-pollution control); 5—the limitations of coal cleaning and boiler size and cost as related to fuel characteristics; 6—future possibilities and conclusions. The development of combustion apparatus for power boilers is progressing at a lively pace. There has been no letup in improvements in design of pulverized-coal-fired boilers, and there is a strong trend at present toward improving dry-bottom units. Spreader stokers with overfire jets and dust collectors as standard equipment are gaining favor. Less than 10 years in commercial use, cyclone burners are going into numerous installations here' and abroad.' Underfeed and traveling-grate stokers have long since been developed for heavy-duty operation, yet new developments in overfire jets and humidification of air blast have improved their performance. A water-cooled vibrating-grate stoker of German origin is being introduced into the United States and Canada." The primary objectives of an ideal coal combustion device are: capacity to burn the variety and sizes of coals likely to be economically available during the life of the unit; capacity to burn the coals automatically for a wide load range and rapid load fluctuations and to burn the coals completely to CO2, H2O, and SO2, which means without smoke and cinders, or carbon in the refuse; capacity to control and discharge all the ash in final granular form without ash adhesion to walls or tubes, and without flue dust; minimum furnace volume; minimum labor and maintenance; low initial and operating cost. Regardless of the method of burning, the gaseous products of coal combustion are N2, CO2, O2, H20, and SO?. By way of illustration, the coal analyses in Table I is assumed from an installation described by E. McCarthy.' When coal is burned with 20 pct excess air (theoretical air, 9.23 lb per lb of coal), the quantities of combustion gas shown in Table II are produced. In addition, the gases carry particles of fly ash, unconsumed cinders, soot particles, and small but significant amounts of vaporized oxides and sulphates of sodium, potassium, lithium, phosghorous, iron, and other metals. In recent years, germanium, one of the rare metals found in coal, has been shown to oxidize and vaporize at combustion temperatures and to be concentrated by reconden-sation at lower temperatures." Pulverized coal and cyclone flames" have peak temperatures of 3000' to 3500°F. Temperatures in fuel beds of large underfeed stokers reach maxima of 3000°F, sufficient to fuse almost any ash and to volatilize some of it. These peak temperatures are above the optimum necessary for rapid combustion, but they hasten heat transfer for ignition as well as boiler heat absorption. Furnace and gas temperatures increase with combustion air preheat. Low excess air has the same effect. Fine coal pulverization and highly turbulent combustion shorten the distance for fuel burnout, increase flame temperature, and speed up heat transfer. Rates of combustion of pulverized coal exceeding 200,000 Btu per cu ft per hr have been demonstrated in atmospheric gas-turbine combusters,

Jan 1, 1955

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

By J. J. Knoerzer

A full-scale operational test was conducted on the Coaltek preheating and pipeline charging system at the Semet-Solvay Div. of Allied Chemical at Ironton, Ohio, for the purpose of determining whether a high-quality blast furnace coke could be made from blends containing at least 75% Illinois No. 6 Coal and at the same time reduce air pollution during the charging of the ovens. The coke produced had similar physical characteristics as compared to our conventional wet-charged coke, with the exception of smaller size for the preheat coke. Air pollution during charging was con- trolled and there were no serious operating problems. The coking time was reduced 25% from our normal 17 hr for wet charging to 12.8 hr for preheated charges. The blast furnace performance with preheat coke was satisfactory.

Jan 1, 1976

By Norman Pilling

The deleterious effect on the mechanical properties of copper, resulting from heating in contact with reducing gases, is well known, but the mechanism of the action does not appear to have been definitely established. The purpose of the present investigation was not to determine the exact variations in physical quality of commercial copper, with its various impurities, as dependent upon the composition of the gas, temperature of exposure, etc., but rather to study the nature of the action and the conditions under which it occurs. The physical result of the so-called "gassing." of copper has been generally described as the development of "brittleness." There appears to be a striking decrease in tensile strength, associated with a considerable loss of ductility, and a small copper strip or wire affected in this way can he snapped in two when bent. Larger articles may have an outer layer alone affected, which can be detached from the core by hammering or bending. Perhaps the earliest reference to this subject is that of Heyn1 in 1900, and among the later observers may be mentioned Archbutt,2 Bengough and Hill,3 Johnson,4 Mathewson and Thalheimer,5 and Ruder .6 Bengough and Hill, while working with arsenical copper, were the first to suggest the possibility of the formation of gases within the copper itself, while Ruder endeavored to explain the action by the reduction of the

Jan 10, 1918

By Leon Nelson

SEVERAL factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in. square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation.

Jan 1, 1937

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

Jan 3, 1976

By G. E. Kedzie

The ore-deposits of ail that portion of the San Juan country within the borders of Ouray County are either in the tertiary ernptives or, confined to a relatively narrow zone, in the sedimentary beds just beneath them. The ore-deposits in the igneous formation

Jan 1, 1888

By C. J. Ramsburg

The construction and operation of by product coke-oven plants in America are essential to strong national defense and of the greatest importance to many widely diversified undertakings as well as to safety and health. Carbonization Process Coal used under a boiler or in a locomotive is consumed by combustion. Coal used in a by-product oven is distilled or carbonized, meaning that heat is applied to the coal, out of contact with air, causing a distillation that removes the volatile matter in the coal in the form of gas and vapor, leaving coke as a final product. From the gas and vapor distilled from the coal, many valuable substances can be secured, known as by-products. Hence the name "by-product oven." The simplest example of this principle can be shown by means of an ordinary clay pipe. If powdered coal is placed in the bowl of the pipe, the opening of the bowl is plugged with clay, and the bowl placed in a flame, the bowl will become hot, transferring the heat through the wall of the bowl to the coal within. When this coal attains a temperature of about 750°F., gas will begin to pour out of the pipe stem, and this gas may be lighted. A black liquid also will exude from the stem of the pipe, This is tar mixed with certain other products. What remains in the bowl after distillation is coke. A coke oven corresponds to the bowl of the pipe. A modern oven of the latest type is a refractory brick chamber approximately 42 ft. long and 14 ft. high, averaging 18 in. in width. The oven is filled with coal through closable charging holes in the oven top. Each end of the oven consists entirely of a self-sealing door, the removal of which permits the finished coke to be discharged by means of a power-operated pusher machine. The ovens are built in batteries, and the heating is effected by gas burned in vertical flues in the oven walls, each set of flues heating the walls of two adjacent ovens. Such ovens carbonize a charge of approximately 18 tons of coal in 18 hr., or have a daily throughput of 24 tons per oven, producing about 17 tons of coke. In times of need, the output may be increased by raising the temperature of flues, thus shortening the coking time. There is one great essential difference in principle between distillation in a clay pipe and in a coke oven. In the 18-in. oven, the distillation proceeds from two parallel walls held at a high temperature (over zooo°F.) and instead of all the coal being heated at once, the distillation is a progressive one creeping inward. The average travel of this heating is 35 in. per hour from each vertical wall, and as the volatile products are formed progressively they must push away from the interior toward the wall through the previously formed hot coke, then up the walls and Over the top of the coal charge, finally escaping through the outlet pipe. This results in a cracking of the components into many different and valuable substances not formed when the carbonizing temperature is low.

Jan 1, 1942

By G. P. Gladis, R. H. Atkinson

Palladium has been used for jewelry for many years, particularly in conjunction with gold. This use increased in amount during the war, as palladium and gold were only moderately used for war purposes while demands for platinum and some of the other members of the platinum group were so great that their use in jewelry was prohibited. Palladium hardened with a small percentage of ruthenium has the necessary technical properties and appearance for good jewelry, and it is sufficiently rare to be desirable for luxury items—at least I00 times as rare as gold. Although both visual and spectro-photometric examination demonstrated that the color of Palladium was almost the same as that of platinum, a few jewelers found the surface of palladium, even after some polishing, rather dark in areas that had been repeatedly heated during the soldering necessary to assemble certain types of handmade ornaments. This phenomenon is not to be confused with the thin, bluish oxide film that can be produced by heating in air over the range 400' to 800°C., as that film is easily reduced by dipping in warm 5 per cent formic acid or in warm methanol. It was suspected that the difficulty arose from heating in atmospheres that were alternately oxidizing and reducing, as Wise and Vines1 had found that this opened the grain boundaries of palladium and palladium-silver alloys in the same manner as in pure silver, as reported by Martin and Parker.2 This damage is caused by the reaction between oxygen in solid solution in the metal, acquired when heated under oxidizing conditions, and hydrogen diffusing in from subsequent heating under reducing conditions; the steam cannot diffuse out and therefore builds up sufficient pressure to disrupt the metal near the surface. Copper and various other metals can be damaged similarly, but platinum is nearly immune; therefore the problem was new to the platinum jeweler. Sulphur in the fuel gas also can cause trouble but did not appear to be dominant in the present instance. Metallographic examination of both pure palladium and ruthenium-palladium showed that the usual torch using oxygen and city gas as normally operated did in fact cause the surface and subsurface damage that had been observed, and also disclosed that a reducing flame caused more damage than an oxidizing flame and was very damaging even in the absence of any intentional swing in atmosphere from oxidizing to reducing (Fig. 7); besides the surface damage, there was serious loss of ductility. A full explanation of the mechanism of attack is not evident at the moment, but may be allied to the attack that occurs on heating catalytically active metals in nonequilibrium atmospheres.

Jan 1, 1946

By T. H. Dunn, P. L. Menaul

This paper discusses the results of an investigation made to develop a method of combatting corrosion of subsurface oil-well equipment caused by brines containing hydrogen sulphide. Carbon monoxide, aldehydes, and certain cyanide compounds were found by laboratory tests to effectively inhibit corrosion of steel by sulphide brines. Experiments were made for one year in eight wells in West Texas fields using formaldehyde as an inhibitor. It was found that the inhibitor treatment successfully prevented the severe corrosion previously experienced in these wells, and effected important net savings in operating costs. Introduction Corrosion of oil-field equipment has long been a problem in areas producing sour crudes. These areas include the major fields of Arkansas, Western Kansas, West Texas and New Mexico. Corrosion in these fields is caused primarily by the chemical action of hydrogen sulphide in the presence of water and by electric currents entering the wells through flow lines. Hydrogen sulphide is noncorrosive to iron or steel in the absence of water but under the usual conditions prevailing in oil wells where more or less water is present, hydrogen sulphide is very corrosive. This type of corrosion occurs over the pH range below 9, which includes all natural oil-field brines. If air is present in addition to hydrogen sulphide and water, corrosion proceeds at an extremely rapid rate. It was reported several years ago that a string of oil-well tubing was literally dissolved within 50 days where an air lift was used on a well producing considerable water and hydrogen sulphide. Air is generally absent in wells producing sour crude. After hydrogen sulphide corrosion starts, it proceeds with increasing severity and its correction becomes progressively more difficult. This characteristic of sulphide corrosion has been attributed to the formation of galvanic couples between the iron and steel equipment on one hand and the products of corrosion on the other.' Severe corrosion of subsurface oil-well equipment leads to a multitude of troubles. In addition to destruction of costly equipment, producing sands often are damaged by flooding with water leaking through corroded casing; bad mechanical conditions may develop in a well due to obstructions caused by corroded equipment lost in the hole, or partly collapsed casing; pumping operations are interfered with, and severe emulsification problems may result from the homogenizing action of corroded balls and seats.% A typical case of severe corrosion caused by hydrogen sulphide was reported in Howard County, Texas, where it was necessary to pull tubing once a week to repair leaks after the tubing had been in use for only one year. On one well in this area a string of tubing was pulled 11 times in 8 months; 11 joints of tubing being replaced because of leaks. In Ector

Jan 1, 1946

By R. I. Jaffee, C. T. Sims, C. M. Craighead

The fabrication of rhenium metal by powder metallurgy techniques is discussed. The following physical and mechanical properties have been measured and are reported: lattice constants, melting point, electrical resistivity, thermal expansion, spectral emissivity, modulus of elasticity, tensile properties and ductility at room and elevated temperatures, work hardening, recrystallization, grain growth, and oxidation resistance. IT is only occasionally that a metal reaches present-day technology with as little known about its properties as element No. 75, rhenium. Relatively scarce to date, it has been studied only infrequently and used less. Previous work on rhenium has been carried out primarily by European scientists. However, realization that rhenium occurs in commercial quantities in the United States recently has focused attention on this metal. Rhenium is a very dense high melting hexagonal-close-packed metal. Like tungsten and molybdenum, its highest oxide is volatile. However, when protected by reducing or inert atmospheres, its strength at high temperatures is greater than that of tungsten. Rhenium work hardens more than any other known pure metal, but, on annealing, becomes quite soft and ductile. Its vapor pressure is approximately that of tantalum, but it does not enter into the so-called "water cycle" nearly as readily as does tungsten. (The water cycle is a deleterious phenomenon causing blackening of lamp bulbs and vacuum tubes with subsequent failure of the filaments.) These and other properties, some already known and some found as a result of the current researches, have indicated that rhenium has many potential uses, primarily of an electrical or electronic nature. Rhenium or its alloys soon may be found in service as electron-tube filaments, cathodic emitters, or as electrical contact materials. In addition, rhenium or its alloys have potential use in such devices as high temperature thermocouples, and high wear-resistant parts such as precision instrument points. Rhenium, in the form of potassium perrhenate, was made available for this study by the Kennecott Copper Corp. The potassium perrhenate was reduced to rhenium metal in two stages, accompanied by leaching to remove potassium in the form of hydroxide. This impure metal was then oxidized to rhenium heptoxide and dissolved in water. The solution was neutralized with ammonium hydroxide to produce highly purified ammonium perrhenate, a typical analysis of which is shown in Table I. The ammonium perrhenate was ground to —325 mesh in a rubber-lined ball mill with Burundum balls. This operation caused a certain amount of impurity pickup, as reflected in the rhenium analysis shown in Table I. The fine ammonium perrhenate was reduced to metal with hydrogen. Particle size of the powder ranged from 1 to 25 microns, as illustrated by Fig. 1.

Jan 1, 1956

By Robert Maddin

THE application of electrolytic polishing of metals introduced a new technique for preparing surfaces, especially for single crystals. This procedure has generally been assumed to eliminate the strain introduced by mechanical polishing and to result in a more truly representative surface, particularly in the case of soft metallic materials. However, apparently little information is available concerning specific characteristics of a surface prepared electrolytically. The conventional method of mechanical polishing is known to produce a layer of distorted metal which is usually removed by a suitable chemical etchant. To what depth the strain introduced by mechanical polishing penetrates into the lattice is still obscure. The present investigation illustrates the apparently anomalous appearances of glide ellipses on electrolytically polished surfaces of aluminum single crystals. EXPERIMENTAL PROCEDURE AND RESULTS Aluminum single crystals, 99.975 pct pure, remaining from the investigation of Found,1 were polished electrolytically using a solution of fluoboric acid and a low current density. Laue back-reflection technique, interpreted after the manner of Greninger,2 was used to determine the orientation and the specimen axis rotation of the crystals. Three flat surfaces about 4 mm wide parallel to the specimen axis, one perpendicular to the theoretical slip direction and the other two 1200 apart, were polished mechanically and repolished electrolytically. A tensile load was applied using a Southwark-Emery tensile machine at a rate of about 40 lb per min. Elongation was measured by noting the initial and final gauge lengths. X ray diffraction was used to obtain the usual X and X values in order to calculate the elongation and shear by plotting stereographically the specimen axis rotation by means of the Schmid-Boas formula.3 In Table I may be found the value of the gauge diameter, measured elongation, calculated elongation and shear for the crystals investigated. Fig 1 shows the initial and final positions of the specimen axes of the crystals. [ ] At a low magnification the slip lines developed on specimen Al-I appeared straight and rather evenly spaced. However, at a high magnification, the slip lines were seen to be composed of small markings which were present throughout the length of the specimen (Fig 2). The distance between the markings was fairly constant and their directions all parallel to one another. Fig 3-5, photographed on different surfaces of the specimen, illustrate the interesting appearance of these lines. It may be noticed from Fig 4 that the markings, which present the appearance of

Jan 1, 1948

By G. P. Gladis, R. H. Atkinson

Palladium has been used for jewelry for many years, particularly in conjunction with gold. This use increased in amount during the war, as palladium and gold were only moderately used for war purposes while demands for platinum and some of the other members of the platinum group were so great that their use in jewelry was prohibited. Palladium hardened with a small percentage of ruthenium has the necessary technical properties and appearance for good jewelry, and it is sufficiently rare to be desirable for luxury items—at least I00 times as rare as gold. Although both visual and spectro-photometric examination demonstrated that the color of Palladium was almost the same as that of platinum, a few jewelers found the surface of palladium, even after some polishing, rather dark in areas that had been repeatedly heated during the soldering necessary to assemble certain types of handmade ornaments. This phenomenon is not to be confused with the thin, bluish oxide film that can be produced by heating in air over the range 400' to 800°C., as that film is easily reduced by dipping in warm 5 per cent formic acid or in warm methanol. It was suspected that the difficulty arose from heating in atmospheres that were alternately oxidizing and reducing, as Wise and Vines1 had found that this opened the grain boundaries of palladium and palladium-silver alloys in the same manner as in pure silver, as reported by Martin and Parker.2 This damage is caused by the reaction between oxygen in solid solution in the metal, acquired when heated under oxidizing conditions, and hydrogen diffusing in from subsequent heating under reducing conditions; the steam cannot diffuse out and therefore builds up sufficient pressure to disrupt the metal near the surface. Copper and various other metals can be damaged similarly, but platinum is nearly immune; therefore the problem was new to the platinum jeweler. Sulphur in the fuel gas also can cause trouble but did not appear to be dominant in the present instance. Metallographic examination of both pure palladium and ruthenium-palladium showed that the usual torch using oxygen and city gas as normally operated did in fact cause the surface and subsurface damage that had been observed, and also disclosed that a reducing flame caused more damage than an oxidizing flame and was very damaging even in the absence of any intentional swing in atmosphere from oxidizing to reducing (Fig. 7); besides the surface damage, there was serious loss of ductility. A full explanation of the mechanism of attack is not evident at the moment, but may be allied to the attack that occurs on heating catalytically active metals in nonequilibrium atmospheres.

Jan 1, 1946

By C. J. Ramsburg

The construction and operation of by product coke-oven plants in America are essential to strong national defense and of the greatest importance to many widely diversified undertakings as well as to safety and health. Carbonization Process Coal used under a boiler or in a locomotive is consumed by combustion. Coal used in a by-product oven is distilled or carbonized, meaning that heat is applied to the coal, out of contact with air, causing a distillation that removes the volatile matter in the coal in the form of gas and vapor, leaving coke as a final product. From the gas and vapor distilled from the coal, many valuable substances can be secured, known as by-products. Hence the name "by-product oven." The simplest example of this principle can be shown by means of an ordinary clay pipe. If powdered coal is placed in the bowl of the pipe, the opening of the bowl is plugged with clay, and the bowl placed in a flame, the bowl will become hot, transferring the heat through the wall of the bowl to the coal within. When this coal attains a temperature of about 750°F., gas will begin to pour out of the pipe stem, and this gas may be lighted. A black liquid also will exude from the stem of the pipe, This is tar mixed with certain other products. What remains in the bowl after distillation is coke. A coke oven corresponds to the bowl of the pipe. A modern oven of the latest type is a refractory brick chamber approximately 42 ft. long and 14 ft. high, averaging 18 in. in width. The oven is filled with coal through closable charging holes in the oven top. Each end of the oven consists entirely of a self-sealing door, the removal of which permits the finished coke to be discharged by means of a power-operated pusher machine. The ovens are built in batteries, and the heating is effected by gas burned in vertical flues in the oven walls, each set of flues heating the walls of two adjacent ovens. Such ovens carbonize a charge of approximately 18 tons of coal in 18 hr., or have a daily throughput of 24 tons per oven, producing about 17 tons of coke. In times of need, the output may be increased by raising the temperature of flues, thus shortening the coking time. There is one great essential difference in principle between distillation in a clay pipe and in a coke oven. In the 18-in. oven, the distillation proceeds from two parallel walls held at a high temperature (over zooo°F.) and instead of all the coal being heated at once, the distillation is a progressive one creeping inward. The average travel of this heating is 35 in. per hour from each vertical wall, and as the volatile products are formed progressively they must push away from the interior toward the wall through the previously formed hot coke, then up the walls and Over the top of the coal charge, finally escaping through the outlet pipe. This results in a cracking of the components into many different and valuable substances not formed when the carbonizing temperature is low.

Jan 1, 1942

By R. J. Sandrea, S. M. Farouq Ali

The results of an experimental and theoretical study of the effects of rectilinear impermeable barriers and highly permeable channels on the sweep efficiency and conductivity of a five-spot network are presented. The study was carried out using Hele-Shaw, and conductive sheet analogs for both. normal and inverted flood patterns. A functional relationship was developed which provides quantitative prediction of the above parameters; i.e., sweep efficiency and conductivity, for the nonhomogeneous system. To evaluate this, it is necessary only to measure the interference modulus of the obstacle using a simple expression. The results indicate that impermeable barriers, with an interference modulus greater than zero, always cause a decrease in the conductivity and the sweep efficiency of the pattern. On the other hand, permeability channels do not have a significant effect on these parameters, unless they are located along the streamlines. The study also discusses a method of formulating the difference equations pertaining to the two-dimensional Laplacian in a system containing rectilinear barriers. In addition, a technique is described for tracing the progress of a free surface, using marked particles, in a stream containing discontinuities SuCh as those occurring at the extremities of barriers. The above computational scheme was used in a digital computer program to simulate results of the Hele-Shaw analog. The computed values of sweep efficiency mere in good agreement with the experimental values. INTRODUCTION At the present time waterflooding remains the most widely used technique for the secondary recovery of oil. Among the numerous factors that affect the performance of a waterflood, the areal sweep efficiency constitutes one of the most critical parameters. It is a function only of the geometric distribution of the wells for a homogeneous medium and unit mobility ratio. Geological considerations, however, such as the presence of sealing faults or solution channels in the rock matrix, would generally exert an adverse effect on the areal sweep efficiency of a waterflood network. Surprisingly little information is presently available on the quantitative implications of such permeability interferences. It was the object of this investigation to consider the presence of rectilinear, impermeable and highly permeable interferences in an otherwise homogeneous five-spot pattern, and to analyze their effects on the resulting sweep efficiency and pattern conductivity. The experimental phase of the study was conducted using two different models: the Hele-Shaw flow cell and the field plotter. For experimental convenience, the geometric boundaries of the five-spot were assumed to constitute streamlines even in the case where the interference was asymmetrically placed with respect to a repeated five-spot pattern. A second object of the study was to develop a computational scheme for numerically calculating the pressure distribution in a five-spot flow pattern containing rectilinear, impermeable barriers, and to use this distribution to compute the sweep efficiency. EXPERIMENTAL PROCEDURE HELE-SHAW ANALOG The Hele-Shaw analog was used both as a visual model and for determining the sweep efficiency for systems involving impermeable barriers. The physical limitations of this model as a means of experimentally studying the motion of a fluid in porous medium have been adequately discussed elsewhere.2,7 Likewise, it can be easily verified that the analogy remains valid when a portion of the region between the plates contains an obstacle of the same thickness as the distance between the plates. The model used in this study was composed of

By T. H. Dunn, P. L. Menaul

This paper discusses the results of an investigation made to develop a method of combatting corrosion of subsurface oil-well equipment caused by brines containing hydrogen sulphide. Carbon monoxide, aldehydes, and certain cyanide compounds were found by laboratory tests to effectively inhibit corrosion of steel by sulphide brines. Experiments were made for one year in eight wells in West Texas fields using formaldehyde as an inhibitor. It was found that the inhibitor treatment successfully prevented the severe corrosion previously experienced in these wells, and effected important net savings in operating costs. Introduction Corrosion of oil-field equipment has long been a problem in areas producing sour crudes. These areas include the major fields of Arkansas, Western Kansas, West Texas and New Mexico. Corrosion in these fields is caused primarily by the chemical action of hydrogen sulphide in the presence of water and by electric currents entering the wells through flow lines. Hydrogen sulphide is noncorrosive to iron or steel in the absence of water but under the usual conditions prevailing in oil wells where more or less water is present, hydrogen sulphide is very corrosive. This type of corrosion occurs over the pH range below 9, which includes all natural oil-field brines. If air is present in addition to hydrogen sulphide and water, corrosion proceeds at an extremely rapid rate. It was reported several years ago that a string of oil-well tubing was literally dissolved within 50 days where an air lift was used on a well producing considerable water and hydrogen sulphide. Air is generally absent in wells producing sour crude. After hydrogen sulphide corrosion starts, it proceeds with increasing severity and its correction becomes progressively more difficult. This characteristic of sulphide corrosion has been attributed to the formation of galvanic couples between the iron and steel equipment on one hand and the products of corrosion on the other.' Severe corrosion of subsurface oil-well equipment leads to a multitude of troubles. In addition to destruction of costly equipment, producing sands often are damaged by flooding with water leaking through corroded casing; bad mechanical conditions may develop in a well due to obstructions caused by corroded equipment lost in the hole, or partly collapsed casing; pumping operations are interfered with, and severe emulsification problems may result from the homogenizing action of corroded balls and seats.% A typical case of severe corrosion caused by hydrogen sulphide was reported in Howard County, Texas, where it was necessary to pull tubing once a week to repair leaks after the tubing had been in use for only one year. On one well in this area a string of tubing was pulled 11 times in 8 months; 11 joints of tubing being replaced because of leaks. In Ector

Jan 1, 1946

By Cloyd M. Smith

A few years ago, the Ventilation Committee established the practice of resenting one topic each year for discussion at the annual meeting. The practice has met good response on the part of committee members and I suggest that it be continued. The topic chosen for this year, "Underground Anemometry," is a topic which has bothered me for more than 20 years. It seems to me that the coal industry is content to rely on slipshod methods for measuring the rate of flow of air underground, so I prefaced my discussional charge to committee members with the statement that I regard air measnrements made in the usual way, with hand held anemometer, as no good. Agreements and disagreements came in from more than a dozen engineers, some of whom are with operating companies, coal and metal; some with manufacturers; others with government agencies. The statement was accompanied by a questionnaire on the use of the rotating vane anemometer and by one describing two methods of using a mechanically held anemometer. The questionnaire will be considered first. The questionnaire and statement are as shown on pages 5 and 6, the committee members and respondents are given on page 4, and the general comments of the latter on page 5. Questionnaire 1. Has your company or agency issued written instructions for care and use of anemometers? If so, please enclose a copy with reply. Only one answer, McElroy's, was affirmative. It gave reference to Bureau of Mines publications1'5 which recom- mend the hand held anemometer for rough measurements and indicate that am accuracy of 5 pct can be had if calibration and method factors are used. Mathews said that instructions are principally oral while Maize reported that state inspectors of his department are well trained in use and care of anemometers. 2. Are your anemometers calibrated periodically? If so, by their manufacturer? or by? Are calibralion corrections applied to all observed mean velocity readings? Only one respondent, Lee, answered negatively as to calibration. This means that anemometers are generally calibrated but the questionnaire failed to ask how often this is done. As no one volunteered the information, we have no data on this point. In six cases the instruments are sent to their manufacturers for calibration. but Krickovic reports that his company limits manu-facturers' calibrations to anemometers which are used by operating personnel; those used by the engineering department being calibrated by U. S. Bureau of Standards. The Anaconda Copper Mining Co. has its ventilation engineers calibrate its anemometers. Most of the respondents say that a calibration correction is applied to each mean velocity reading, but Krickovic limits this to surveys made by the engineering department. Since Lee does not calibrate, he has no correction to apply. Maize reports that his department has its anemometers calibrated but does not apply corrections. 3. Do your men hold the anemometer by hand in measuring air flow? for 1 min? or traverse the section? for 1 min? or at? points for 5 sec each? Of 10 replies, 6 were "yes," 3 were "no," and one was "seldom" with respect to holding by hand. Among the six hand holders, four hold in a central position in the measuring section for a minute, except that two of them, Krickovic and Matthews, traverse the section by hand for survey or fan test. Their operating personnel hold by hand, centrally, for routine measurements. McElroy sometimes traverses with hand-held anemometer in rapid survey work. 4. If the anemometer is not held by hand, how is it supported? Augustadt supports the anemometer on an adjustable rod, Condon on "a rod of sufficient length to reach all points with observer standing in one position throughout traverse and at arm's length from plane of traverse." I presume that arm's length must be interpreted liberally enough to allow for arm movement, otherwise it would be impossible to manipulate the anemometer throughout the traverse section. Mancha upholds Condon in this method of traversing. Glanville hangs the anemometer on the end of a 4-ft staff by the hasp at the top of the anemometer frame. McElroy mounts it on the end of a rigid square shaft, 12 in. long, the staff being at right angles to the axis of the instrument. He traverses the section in two halves, holding the anemometer 3 feet from his body.

Jan 1, 1950

By R. D. Sprague, C. B. Richardson

The year 1938 was the most active and successful in the history of the oil industry in southern Louisiana. Drilling showed a 16 per cent increase over that of 1937, with a total of 538 wells drilled, which yielded 315 oil wells, 19 distillate wells, 4 gas wells and 200 dry holes. Nineteen new fields were discovered during the year, all but three of which were completed by plugging back to sands previously drilled through. Electrical logging played a large part in these new discoveries as well as in the discovery of new sands during routine development of fields. Fourteen of the new discoveries produced oil, and five produced only gas and distillate. Southern Louisiana continues to lead the world in depth of drilling, which is in part due to the great thickness of comparatively young deltaic sediments near the coast and the existence of numerous sands. The present development is rather evenly distributed over a coastal strip 100 miles wide. New Fields North Tepetate, Acadia Parish.—Atlantic Refining Company's No. 1 Klumpp was completed for a new field through perforations from 7960 to 7970 ft. The initial production was 65 bbl. of 54" gravity distillate and 4 million cubic feet of gas daily through a 1/4-in. choke with tubing pressure of 2850 Ib. and casing pressure of 2930 lb. The well is in see. 12, 7 S., 2 W., just north of Tepetate field. It was drilled to a depth of 8705 ft. and plugged back for its final completion. Atlantic's NO. 2 was completed in a new sand at 8300 ft., also for distillate. South Crowley, Acadia Parish.—Humble Oil and Refining Company's No. 1 Boyd Finch was completed in July 1938, as an oil well through perforations from 7318 to 7325 ft. after plugging from a total depth of 10,222 ft. After making several hundred barrels of oil, the well went to

Jan 1, 1939