Search Documents

By Robert I. Jaffee, Bruce W. Gonser

RECENT work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C. and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. MATERIALS AND ALLOYING As in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni, and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about 1050°C., and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. THERMAL ANALYSIS In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,1 a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946

By Margaret Dienes, Karl L. Fetters

It is recognized that ingot structure is important in determining the quality of finished steel. Such elements of ingot structure as the size, shape and distribution of primary crystals; the size, shape and distribution of shrinkage cavities; the degree and kind of segregation (both macro and micro); the distribution of nonmetallic impurities and gas cavities are each the result of solidification phenomena. 'These structural features vary with variations in ingot practice. Their control requires a knowledge of their correlation with the variables of ingot practice. The structures of full-sized commercial steel ingots have been studied extensively by the Steel Ingots Committee of the Iron and Steel Institute.l This work has contributed much to our knowledge of ingot structure and the factors that control it. These investigations of necessity have been limited in scope because of their costliness and the great amount of time required. Studies of the structure of small steel ingots have not been very satisfactory because of the rapid rate of freezing of the ingots. Their structures are thus difficult to resolve and to interpret. Medium sizes of steel ingots in the ranges of 150 to 500 lb. do offer opportunity for study, but their cost also becomes greater and their use less expeditious. Experimental models for the study of steel-ingot structure have been made of nonferrous metals. Gathmann2 used lead-tin alloys and reported that they were satisfactory for determination of the location of the major shrinkage cavities and the Liplanes of weaknessv resulting from the pattern of crystallization. Certain features of mold design have been illustrated by these results. Bezdenezhnihk3 has used copper and aluminum ingots similarly and has shown the effect of mold-wall thickness on the depth of columnar grains. These studies of nonferrous models have been useful, but their results have been limited because the analogy with steel ingots obviously is not a close one. Model wax ingots have also been useful in pointing out important features of mold design. Gathmann4 watched the solidification of wax ingots, through a glass-walled mold, and has reported the effects of mold type on the location of the shrinkage cavities. Segregation was simulated by using a mixture of paraffin and stearine and adding a red dye that on freezing segregated preferentially to the stearine. Brearley5 also used wax models to determine the effects of some of the principal features of mold design. Carlsson and Hultgren6 dsed stearic acid to show that the columnar crystals of ingots tend to slope upward progressively from the mold wall toward the center of the ingot. As with the nonferrous ingots, the wax ingots have

Jan 1, 1943

By D. R. Uhlmann, T. P. Seward, O. Chalmers

A magnetic field has been used to damp out liquid convection during the solidification of castings. Ingots of Al-2 pct Cu were poured from various sperheats (10" to 65°C) into a room-temperature graphite mold located between the poles of an electromagnet. The effect on ingot structure of varying the strength and time of application of the magnetic field was investigated, and the results are interpreted in light 01- current theories of ingot structure. In the solidification of alloy systems, thermal gradients in the melt and differences in density of the constituents are expected to produce convective motion in the liquid. The thermal convection caused by temperature gradients should be present during the freezing of both alloys and pure materials, while the solute convection caused by density differences should be of concern only for alloys. The possible influence of this natural convection on the structure of castings has been discussed by Ruddle,' Chalmers, and Tiller. More recently, an experimental investigation of such effects was carried out by Cole and Bolling. These workers took stationary molds containing lead- and tin-based alloys and. using a brine solution. quenched them from various superheats above their respective liquidus temperatures. When grids were placed across the mold diameter to suppress convection, the grid region was later observed to contain a larger percentage of columnar grains than other parts of the casting or than similar castings poured without the grids present. From thermocouple measurements, they found the temperature in the grid region to be higher than that in the region outside the grids throughout the freezing process, and concluded that convection should be an important mode of heat transfer in normal castings. In addition to such convection arising from thermal gradients or differences in density of the constituents, a further source of convective motion, which we shall call "momentum convection", may be particularly important in small (laboratory-size) castings. By this term we refer to the convective motion produced in the initial pouring process, a motion which is damped out as the linear momentum and angular momentum of the liquid are dissipated. Besides these sources of convection, which are present to some extent in all castings. external influences may also be effective in producing convective motion. Examples of such "forced" convection which have been discussed in the literature include stirring the melt, shaking the mold, rotating the mold, and so forth The purpose of the present study was to examine the effect of convection on the structure of castings poured into a cold mold. In this work, a magnetic field was employed to damp out the convective motions within the liquid, and hence control the extent of con- The effect of a magnetic field on convective currents in a conducting liquid is to induce eddy currents which oppose and damp out the convective motion. vection. The technique of magnetic damping was previously used by Utech and F1emings" in their study of convective effects on impurity banding and other substructure in alloy crystals grown unidirectionally from the melt. In their investigation, fields as small as 200 gauss were found to be effective in damping the convection currents which influence the banding. I) EXPERIMENTAL TECHNIQUE In the present study, alloys of A1-2 wt pct Cu were poured into a room-temperature graphite mold. The mold, in the shape of a circular cylinder, 2 in. ID, 2-3/4 in. OD, 5 in. inside height, and 5-1/2 in. outside

Jan 1, 1967

By R. A. Fitch, J. D. Griffith

A performance calculation method was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods. of improving their efficiency. The calculation method is based upon the division of reservoirs into multiple independent zones or strata. Comparison was made with some experimental floods and with a field project to obtain some measure of the applicability of the method. Two aspects of miscible flooding were considered: (I) the displacement of a miscible front through a reservoir, and (2) the distribution and utilization of the solvent volume injected to maintain miscibility. Calculations and experihental observations indicate that alternate gas-water injection behind a miscible front significantly improves miscible flood performance, both within a single stratum and in a multistrata reservoir. Calculations were made on the extent to which miscibiliry is maintained by a given solvent volume in a stratified reservoir. Two alternate criteria for determining the optimum volume of solvent for injection are discussed. The preinjection of a small volume of water ahead of the solvent is suggested as a method of obtaining more efficient utilization of solvent. Calculations and experiments were made to investigate the effects of water preinjection. INTRODUCTION Miscible fluid displacement as a possible means of recovering oil has been the subject of extensive research and numerous field tests over the past several years. This work has brought out both favorable and unfavorable features of the miscible recovery methods. Many tests have shown that a miscible fluid can displace all of the oil contacted, leaving no high residual oil saturation, as is characteristic of immiscible displacements. The miscible methods have proven dificult to control, however, as evidenced by early breakthrough of the displacing fluid and poor sweep efficiency in several field projects. It became apparent early in the investigation of miscible displacement that the development of improved techniques and better methods of control would be required to extend the range of applicability to any significant portion of our petroleum reservoirs. The purpose of this study was to consider the problem of designing miscible floods to obtain better performance. A performance calculation was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods of improving their efficiency. Two aspects of miscible floods were considered separately in this study and the results are presented in two parts. The first part concerns the manner in which the miscible front is displaced through the reservoir. In these calculations the condition of miscibility between the reservoir oil and the displacing fluid is assumed. In the second portion the distribution and utilization of the preinjected solvent in maintaining rniscibility is considered. This portion dealing with solvent utilization applies only to the enriched gas or LPG slug processes. CALCULATION METHOD AND EXPERIMENTAL STUDIES COMPUTATIONAL MODEL The calculations for expected reservoir performance are based upon the multi-strata concept of reservoir properties. The method assumes multiple, independent strata (no crossflow between strata) and explicitly includes variations in patterns, injectivity, areal sweep and displacement efficiency. Lateral variation in permeability within the strata (for example, directional permeability) may be considered in the calculations, provided the variations are similar in all strata. The calculations based on this model furnish the rates of injection and rates of production of both oil and the displacing fluid for the composite system of strata. To carry out calculations on the mathematical model described, information is required on the performance of the displacement process under consideration in a single stratum element of the pattern to be used. In particular, for a given pattern and displacement process, data are required relating injectivity and composition of the produced stream to the volume of fluid injected. Data on the variations in areal sweep must also be available if it is desired to track the areal sweeps in the multi-strata model. These data may be obtained from experimental work such as model studies or other suitable methods. This representation of reservoir properties is, of course, an approximation and may be inappropriate in some cases. But the representation is not an arbitrary one since most oil reservoirs are essentially successive layers of sediment with the net producing pay zone often comprising but a fraction of the gross formation thickness. The fact that permeabilities measured in the vertical direction are frequently but a fraction of the horizontal permeability adds some evidence to the validity of this model. This type cal-

Jan 1, 1965

By J. Walter Scott

IT is usual practice in the copper industry to use open horizontal molds for casting tough-pitch copper wire bars.1 A wire bar cast in this manner is partly characterized, by heavy wrinkles and a comparatively deep skin of oxide on the top of the bar, corresponding to the open side of the mold. On the theory that the rough, high-oxide surface might have an adverse effect on the rolling and drawing properties of a wire bar and might account for some of the irregularities of mill behavior, several bars which had been planed to remove the wrinkled surface were processed into wire. These bars responded to mill treatment more satisfactorily than did the regular wire bars. Realizing that machining the surface of one face of each bar would not be commercially feasible, it was decided that casting the metal into a vertical mold and cropping off the pouring end would accomplish. approximately the same result. Several wire bars of commercial size (250 lb.) were so cast and processed into wire for comparative test with bars cast in the usual horizontal molds. It is the purpose of this paper to present the results obtained from this investigation, in which commercial bar sizes and processing technique were used throughout. The results show that in general copper wire bars cast vertically are superior to those cast horizontally.

Jan 1, 1930

By Jill Dill Pasteris

Several mineralogical prospecting techniques are used in diamond exploration. Most are concerned with identifying indicator minerals such as pyrope garnet and magnesian ilmenite, which are derived from mantle xenoliths hosted by kimberlites. The first goal of such prospecting is to locate kimberlite intrusions; the second goal is to identify the diamond-bearing kimberlites. Explorationists have worked much less on the indigenous kimberlite phases. The kimberlitic opaque oxides, ilmenite and particularly spinels, promise to be useful in discriminating between intrusion episodes in identified kimberlites, and perhaps in the evaluation and prediction of diamond grades. Several petrologists have showed that spinel compositions and zoning patterns are specific to certain intrusive facies in South African and Canadian kimberlites. Careful evaluation may indicate a correlation between spinel parameters and diamond content.

Jan 1, 1984

By M. J. Mullikin, J. B. Conway

for use in describing combined first- and second-stage creep data. In the above ?o represents the instantaneous strain on loading, ?t the limit of transient creep, ?S the steady-state creep rate, t the time, and ? a constant leading to the exhaustion rate of transient creep. It was noted that this equation was similar in form to that proposed originally2 by McVetty. This type of equation was also suggested by Andrade and Aboav3 in studies of the shear strain of cadmium. Calculation of the constants ?o, ?t, ?, and ?s, in Eq. [ l] is somewhat involved due to the slight complexity of this relationship. In the paper by Garofalo a computer approach based on a least-squares analysis was recommended. Such an approach involves a trial and error solution but when a computer facility is available the difficulties in this calculation are of little consequence. It does mean however that the evaluation of this type of equation would become quite tedious if computer facilities were not available. Some recent studies have identified a fairly straightforward method for calculating the constants in the Garofalo equation. While not leading to a least-squares evaluation the approach is accurate and is recom-

Jan 1, 1967

By C. E. Birchenall, J. R. Stubbles

ThE equilibrium between lead, lead sulfide (PbS), and atmospheres of H2 and H2S has been determined previously by Jellinek and Deubel,' and SudO.' Blbem and Kroger3,4 used Jellinek's data to calculate the sulfur dissociation pressures of PbS crystals (of

Jan 1, 1960

By J. H. Ffolliott

ALL, of the prospects that later became mines in the Ducktown district were discovered prior to 1854, and most of them were exploited before the turn of the century. It is the purpose of this paper to discuss the exploration and current development of the Boyd mine, discovered in 1853. It is in the heart of the Ducktown Basin, in the extreme southeast corner of Tennessee, and is being developed by the Tennessee Copper Co. GEOLOGY The geology of the district has been fully described in many papers. Probably the most complete description is that of Emmons and Laney.1 The rocks of the district are considered to be of Lower Cambrian age and are a part of the Great Smoky formation, consisting mainly of interbedded graywacke and mica schist, in which the ore deposits occur. The ore bodies are included in an area of about 6 sq. miles, 2 miles wide and 3 miles long striking N. 45° E., and may be grouped into three general lode systems. The northeast system, including the East Tennessee, London and Burra Burra ore bodies, and the southeast group, comprising the Polk County, Mary and Calloway deposits, are all characterized by relatively high copper values. The ores of the central system, which includes the Eureka, Boyd, Old Tennessee and Cherokee ore bodies, are low in copper and high in total sulphide content. Boyd mine lies roughly halfway between the Old Tennessee and Eureka ore bodies [ ] and 2500 ft. in the hanging wall of the Burra Burra mine (Fig. 1). Elevation of the surface is about 1725 ft. above sea

Jan 1, 1942

By C. S. Blair

The development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Alabama, in 1908 was an innovation probably unique for any mining organization south of the Ohio River. At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator difficulties in his future operations, which the latter had not anticipated. Eventually, however, the value of having these data became apparent to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1935

By C. S. Blair

The development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Alabama, in 1908 was an innovation probably unique for any mining organization south of the Ohio River. At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator difficulties in his future operations, which the latter had not anticipated. Eventually, however, the value of having these data became apparent to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1935

By C. Edwin Nighman

THE following is a description of the methods used in rescuing men and extinguishing the underground fire at the Pennsylvania mine, Butte, Mont. This fire, which cost the lives of 21 men, began about 9 p.m., Feb. 14, 1916, at or near a ventilating fan on the 1,200 air-shaft station. This shaft at that time was downcast, while the main hoisting shaft was upcast. Owing to the proximity of the fire to the air shaft, the air in the latter soon became heated, and as the fan on the level was not running¬the power having been cut off shortly after the outbreak' of the fire-the aim' shaft became upcast to the 300 level. At this point a blanket of cold air from the surface caused the smoke and gases to he drawn in on that level and carried down again through the workings to the 1,200. A short time after the discovery of the fire, water was turned down the air shaft through a series of pipes around the collar of the shaft, which caused the smoke to recede, below the 300, so that within 2 hr. it was possible to search that level for the missing men. From the above it will be apparent why the air shaft was upcast instead of downcast as under normal conditions, and why men were suffocated at considerable distances from the seat of the fire. The smoke and gases that came up the main hoisting shaft did not diffuse through the workings to any extent. There are doors on all levels in the connections to the main hoisting and air shafts, but-in the confusion and running around many of these doors were left open, and this undoubtedly caused the smoke and gases to spread more rapidly than they would otherwise have done. It was necessary for most of the men on the various levels to pass close to the air shaft in going to the hoisting shaft, and when they encountered the smoke and gases in that vicinity a number turned hack and climbed down with the direction of the air currents and were then suffocated, while all those who passed through the relatively short pall of smoke to the main shaft were saved.

Jan 2, 1917

By F. S. Sinnatt

This paper is the outcome of an extended investigation carried out in association with Dr. L. Slater. The inquiry had been continued in various directions and a number of results are quoted from an investigation recently completed by S. H. Jenkins. In projecting the work some five years ago, the author had in view a general attack on the problem of the spontaneous combustion of coal from an angle that had received little attention. The basic idea was to obtain a "slow motion study" of the active combustion of coal. This included an examination of the conditions prevailing in a mass of coal at the moment when active combustion ceases. It was thought that, if the factors governing the extinction of combustion in coal could be definitely established, it might offer an explanation of the manner in which the spontaneous combustion of coal originates. The inquiry arose from a detailed study of the properties of fusain that the author began in 1918. Fusain seemed to possess characteristics quite distinct from the coal with which it was associated, for if it were collected into a heap and one portion were heated by a small flame the combustion would traverse the whole mass. This combustion was not accompanied by smoke and passed slowly through the heap of material. Later, it was found that coals, including anthracites, would behave in a similar manner provided they were in the form of powder and that the particles were smaller than a certain size. The limiting size of particles is a definite characteristic of the coals investigated. In view of the fact that fusain exists with coal in a state that enables it to undergo this particular form of combustion, it must be assumed, sometimes, to play a definite part in the spontaneous combustion of coal in the goaf (waste). Tables 1 and 2 contain the analyses of samples of dust collected from a mine and from a dust collector. Some idea of the degree of fineness of the particles of fusain may be obtained from a study of the analyses of the dust from the dust collector; 80 per cent. of the dust would pass through a 200-mesh screen while the fusain was concentrated in the finest dust. The material that passed through a 90-mesh screen contained 54 per cent. of fusain while that between a 30- and a 90-mesh only con-

Jan 1, 1925

By A. Sutulov

The segregation process, an alternative to benefi-ciation of oxidized and mixed sulfide-oxide copper ores, is studied here with particular emphasis placed on time, temperature, and coke and salt percentage factors. The results show that in a segregated charge, the copper assay of the coarsest fractions normally is of the same order as the copper assay of the tails obtained from grinding and flotation of the same charge. This observation suggests the possibility of limiting or even eliminating the grinding step from the flowsheet of a segregation plant. The segregation process, which offers an alternative to beneficiation of oxidized and mixed sulfide-oxide copper ores, was discovered in 1923 by Moulden and Taplin1,2 who were attempting to apply the Perkins process3'4 to a Chilean ore from the Sagasca mine. After a number of investigations and pilot plant tests,'-' the segregation process became a successful industrial operation.'r9 The process aroused considerable interest in Chile because of the existance of large reserves of oxidized copper minerals which could not be treated by conventional hydrometallurgical methods because of the high consumption and prohibitive cost of sulfuric acid. During the last two years, the Mineral Dressing Dept. of the Institute de Investigaciones Tecnology cas of University of concepci6n (Chile) has carried out a test program on 23 different ore samples representative of the national territory. These tests were carried out on a semi-continuous and batch scale with a rotary, automatically controlled and gas-fired furnace (supplied by Bartlett and Snow, Fig. 1). The results of these tests indicate that out of the 23 samples 20 can be successfully treated by this process with recoveries of copper ranging from 85 to 95%.10,11 The purpose of this paper is to treat some specific problems related to the segregation process. TIME AND TEMPERATURE FACTORS Time and temperature of calcination play an important role in the segregation process. When moderate salt and coke conditions were maintained (each of reagents was added in the quantity of 1 — % wt), systematic testing easily demonstrated the influence of these two factors on segregation and flotation recovery. The pertinent results are summarized in Fig. 2. To determine what specific changes the segregation process made on the ore, the samples, segregated at 700°C for different periods of time and under standard conditions, were granulometrically analysed and

Jan 1, 1963

By Eugene Leonardon

THE search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out con-tinuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum' of useful samples.

Jan 1, 1939

By E. W. McAllister

THE decision of the California Oil Umpire's1 office to accept well potentials established from subsurface-pressure data has brought to the attention of many operators for the first time the application of such data to production problems. This paper reviews the development and application of subsurface-pressure data in Kettleman Hills, where these data have been used in production work since 1932. The Kettleman Hills field was discovered in October 1928. The first subsurface-pressure surveys were made early in 1932 and by the middle of 1933 the two major operators in the field were making routine pressure runs in their respective wells. Shortly thereafter, these companies agreed to exchange pressure data, and later a third company entered into the agreement. This made it possible to analyze the effects upon the reservoir pressure of past production practices, which are discussed in the latter part of the report. It is interesting that many of the applications of subsurface-pressure data discussed herein were anticipated by C. L. Clarks and C. B. Kimberlin‡ in a reports dated March 1933. PRODUCTIVITY INDEX In the majority of individual well problems involving the use of subsurface pressure data, it is necessary to use a factor known as the "productivity index," which indicates the ability of a well to produce and represents the number of barrels of oil or oil and water per day that will enter the well bore for each pound per square inch pressure drop made opposite the producing interval of the well. The productivity index may be determined from pressure and production data for one or more rates of flow and a static or shut-in pressure survey or from production and pressure data for two or more rates of flow. Productivity indices may be based upon either net oil or total fluid production. All indices referred to in this report are based upon net oil. The value of the productivity index for Kettleman Hills wells decreases generally with time and it is not uncommon for the index to vary in value at any specific time for various rates of flow. The decline of the productivity index may be attributed partly to the loss of reservoir pressure. As. the reservoir pressure decreases, gas originally in solution is released from the oil, congesting the flow of fluids through the formation and increasing the viscosity and surface tension of the oil; thus the flow resistance of the fluids through the formation is increased, resulting in a decrease of the productivity index. For convenient reference, the productivity indices for each well are plotted against time and a curve is drawn through the points showing the trend of the average index value. Plotted on Fig. I are index values for five

Jan 1, 1941

By M. R. Tek, F. H. Poettmann, M. L. Grove

The general problem of single-phase natural gas flow through porous media has been considered both by mathematical analysis and field experiments. Theoretical studies on the fluid dynamics of natural gas wells resulted in derivations of expressions which permit a ber-ter understanding of the flow mechanism for conditions under which Darcy's law is no longer valid. In applying these results to natural gas production and testing technology, special emphasis war placed on the study of low permeability, slowly stabilizing formations. These applications resulted in a method of predicting the performance coefficients of tight natural gas wells. The calculation of the performance coefficient requires the determination of the "test-index", pkh/µ, the drain- age radius, R, and the effective wellbore radius, rw. Methods for estimating these parameters from field data were also developed. Field data from 15 wells were collected and analyzed. The measured values of the performance coefficients were compared with the predicted values. This statistical evaluation gave a bias of 7.14 per cent and a standard deviation of 11.6 per cent. INTRODUCTION The performance of a natural gas well is determined by the physical properties of the reservoir rock, the extent and the geometry of the drainage area, the properties of the flowing fluid, and the conditions of pressure distribution within the drainage matrix. The relation between the quantity of gas delivered and the pressure drop within the reservoir is characteristic of the behavior of each well and is often referred to as the back-pressure behavior of the well. It is well established that for normal, single-phase gas wells the relationship between the gas delivery rates and the bottom-hole pressure take, in general, the form, Q = c(P3 8 -P2 1)n. ,.......(1) where C is the performance coefficient, and n is the exponent corresponding to the slope of the straight-line relationship between Q and (P2 s, — P2 l) plotted on logarithmic coordinates. The determination of a well's performance by the back-pressure behavior not only permits the production engineers to analyze many operating problems, but also provides necessary information useful and essential to predict the future development of the field.' Important engineering and production problems such as calculation of gas deliverability into a pipeline at a predetermined line pressure, design and analysis of gas-gathering lines, determinations of spacing and number of wells to be drilled during field development to meet future market or contract obligations, etc., all depend, at least in part, on the availability and use of reliable back-pressure curves.' In the past the behavior of gas wells was evaluated

Jan 1, 1958

By W. R. Atkins

THE Negaunee mine is at the east end of the Marquette Range, in the city of Negaunee, on the Upper Peninsula of Michigan. Iron ore was first discovered on this property in 1883 by diamond drilling. A shaft was sunk soon afterward, and the mine has been worked continuously ever since. The total shipments from 1887 to' Jan. 1, 1945, were 20,417,587 long tons. The mine was taken over by the present operators, The Cleveland-Cliffs Iron Co., in 1903. During the past four years, 1941 to 1944 inclusive, the property has produced an average of nearly a million tons a year, and has employed more than 400 men. GEOLOGY The ore body at the Negaunee mine lies in a large syncline dipping about 15° to the west, the ore coming to ledge at the east end of the trough. The ore occurs in the Negaunee formation of the middle Huronian age, which consists of ferruginous cherts and slates through which intrusions of diorite have occurred. Although these intrusions of diorite have an important bearing on the formation of ore on the range, they are not important in this ore body. Some faulting has taken place along the diorite intrusions, or dikes as they are called locally, and also other faults are known to exist across the formation. These faults do not complicate either mining or development of the ore body. The footwall consists of jasper underlain with Siamo slate; the hanging wall is jasper and ferruginous chert. Fig. I shows a typical cross section of the ore body. The ore body is quite regular, about 120 ft. thick in the middle of the syncline and thinning out toward both sides of the fold. Its width ranges from 400 to 800 ft., the average being about 600 ft. The footwall is uniform in dip and strike, but irregular lenses of ore often extend 50 to 75 ft. up into the overlying jasper capping. METHOD OF MINING Ore in the Negaunee mine has been mined by top slicing almost exclusively since 1903. This method of mining has been employed because it is especially adapted to the size and shape of the Negaunee ore body, and to the soft, sticky nature of the ore as well as the generally soft, broken jasper capping. Development The ore body has been developed from six different levels with intervals varying between l00 and 125 ft. On the average, the dip causes a horizontal offset of 350 ft. per level, and under these circumstances it has been necessary to carry on considerable development in rock to make available the ore lying along the north and east footwalls. This is not as disadvantageous as might be supposed, because of reduced pressure and the accompanying saving in maintenance costs. The development of the

Jan 1, 1946

By T. M. Geffen, H. N. Hall

One-third to one-half of the original oil is left in most reservoirs even after thorough gas driving or waterflooding. In contrast, essentially all of the oil contacted con be recovered by flooding with a solvent (a fluid miscible with the reservoir oil). It is not economical to fill a reservoir with solvent since the value of the solvent would very likely exceed that of the oil. A practical method would be to inject a small bank of solvent to displace the oil. This solvent bank in turn could be driven through the rock by a less valuable scavenging fluid, such as natural gas which is also miscible with the solvent. Such a method of oil recovery was studied in the laboratory using long (up to 95 ft) core systems. It was found that, as the solvent moves through the reservoir, the front end of the solvent bank becomes mixed with the oil and forms a relatively short mixing zone between undiluted crude oil and pure solvent. An engineering correlation was obtained which can be used to predict the length of this zone. Displacement of the solvent by natural gas can be achieved with complete miscibility (above the critical pressure of the gas-solvent system at reservoir temperature) or with partial miscibility at lower pressures. Under conditions of complete miscibility, it was found that the length of the gas-solvent mixing zone could be predicted from the correlation developed for the solvent-oil mixing zone. With partial miscibility, two phases exist and the solvent is displaced by a modified gas drive in which vaporization and condensation occur. Equations are developed to predict the performance of this type of displacement. Two plans are suggested for application of miscible fluid displacement. one for miscible displacement of the solvent and the other applying to lower pressures where partial miscibility occurs during solvent displacement. Calculations based on the laboratory tests indicated that a bank of solvent with a volume of less than 10 per cent of the hydrocarbon volume under consideration will generally be adequate to obtain high oil recovery from the portion of the reservoir contacted in miscible fluid displacement. INTRODUCTION The conventional methods by which oil is displaced from reservoir rock—solution gas drive, conventional gas drive, and waterflooding—are all processes in which the oil is expelled from the rock by direct displacement with a fluid immiscible with the oil. Because of the immiscible type displacement, complete recovery of the reservoir oil is not achieved. In economically successful flooding operations, as much as 50 per cent of the original oil may be abandoned in the reservoir as unrecoverable. The use of a solvent (miscible with oil, such as LPG) as an injection fluid does not have the undesirable displacement features common to the use of gas or water (immiscible with oil). It can be readily appreciated, however, that it would not be economically feasible to displace the oil and entirely replace it with a solvent. A process was therefore devised for use in field operations in which only a small volume of solvent would be required to obtain essentially complete oil recovery in the portion of the reservoir contacted. In this process, the solvent acts as a buffer between the reservoir oil and injected gas, allowing the natural gas to displace indirectly the oil with much greater efficiency than if the gas displaced the oil directly. DESCRIPTION OF OIL RECOVERY PROCESS The solvent oil recovery process will be described in

Jan 1, 1958

By Heihachi Kamura

In this research, the proper temperature for the reduction of iron ores by carbon monoxide was determined. Also, the difference of the rate of reduction on the sizes of ore under four mesh per linear inch was estimated, but no evidence could be found. Rates of reduction on the seven kinds of ore were compared with the results of the experiment, showing a close relation between reducibility and density of ore. Finally, the maximum size of ore that can be reduced in applicable length of time was determined. The author thinks that the process of production of steel may be replaced by low-temperature reduction of iron ores some time in the future. THE reduction of iron oxide, such as Fe203, to iron in the blast furnace is performed principally by carbon monoxide, but partly by solid carbon by the two following reactions: Fe203 + 3CO = 2Fe + 3CO2 2Fe203 + 3C = 4Fe + 3CO2 It is known that reduction by carbon monoxide takes place at a much lower temperature than reduction by carbon and that the reducing action of carbon monoxide progresses to the inside of the ore in lump form by gaseous diffusion. In the reduction by carbon, however, the reducing action takes place only at the contact surface of the ore and carbon, so that the more complete the reduction by carbon monoxide, the more efficient is the operation. However, the reduction does not progress as shown in the foregoing formula, because carbon dioxide acts oxidizingly on the metallic iron to such a degree that when the gaseous composition reaches a certain proportion of carbon dioxide to carbon monoxide, the reduction practically stops, even though the gases are moving slowly through the heated ore. The proportions of carbon monoxide and carbon dioxide in the gas depend on the kind of iron oxide and the temperature of reduction, also the duration of time in the reaction. The longer the time of the reaction, the higher the proportion of carbon dioxide obtained in the gas, but finally it will attain to a condition of equilibrium.

Jan 1, 1925