Search Documents

By Charles H. Snow

The engineer has often to penetrate difficult or unknown regions. Mineral, irrigation, boundary and railway problems frequently necessitate journeys through, or long residence in, localities whence sustenance cannot be drawn. The selection and conveyance of provisions, outfit and implements thus become a matter of the first importance. Scientific skill, even of the highest order, is powerless unless supported by the proper appliances and foods. The advance of civilization favors the engineer, in that it is constantly enlarging his facilities and thus reducing his difficulties. Notwithstanding this fact, many are yet brought face to face with the problems considered in this paper. Distinction must be made between parties which are to be in constant or even occasional touch with a base of supplies, and those which will be for a long time dependent on their original outfit. Again, the requirements of a party on the march are different from those of a fixed camp. The district, season, cliinate, size and personnel of party also influence the character of the outfit. A party that is to be detached from its base of supplies for some time requires a greater variety of food than if it is to be gone for a short time. Much less in proportion need be taken where the journey is not long, so that privation is confined to a limited period. The ability to establish a fixed camp permits a larger outfit than would be possible if the camp mere to be moved from day to day. Transportation, climatic and other conditions are thus so varied that lists prepared for one work could hardly be applied to any other without some modification. Lists that have proved successful in some instances may, however, serve as bases to be added to, or otherwise altered, for the case in hand. The mistake usually made is in providing too large an outfit. Every emergency cannot be provided for; so that it is well to take, not what may be needed, but what cannot be spared.

Jan 1, 1900

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By David White

In these days, when detailed investigations of stratigraphy, structure, and sand conditions so frequently result in the discovery of new oil fields, and applause from oil companies and the public, geologists do well to walk humbly, and punctiliously to admit that the geologic principles controlling the distribution of oil and gas have as yet been discovered only in part, and that what remains yet to be learned is probably vastly more than what is already known. The few experiments already attempted have been fragmentary, and somewhat desultory, and however positive each of us may be with respect to certain theoretical conclusions, many of the fundamental questions as to the origin and mode of occurrence of petroleum are subject to radical disagreement. Of the chemical changes attending the generation of petroleum from organic matter, little is actually known. Most of the postulated formulas are liable to be misleading, through ignorance of essential factors. Open-minded-ness is therefore a prime essential at the present stage of our science. Nevertheless, adopting the hypothesis that oil originates in some manner fundamentally connected with the organic theory, and in possible departure from such open-mindedness, the writer will pay no attention to the so-called inorganic theory, since every attempt to apply this theory to the study of old oil fields, or to the discovery of new ones, affords cumulative evidence of its inadequacy. In this paper, some of the factors affecting the occurrence of petroleum that the writer believes worthy of consideration by the prospector for oil in any new region will be discussed. Some of these, which arc less generaLly understood, will be considercd somewhat in detail. Other points, the significance of which cannot now be determined, require more field study, and for that reason are here brought to the attention of the field geologist. On the other hand, certain theoretical points which do not bear especially on the oil possibilities of a new region will be given little or no attention. The main topics that will be discussed are: (1) sufficiency of carbonaceous detritus and residues in the oil-forming rocks; (2) stage of carbonization of the organic matter in the oil-bearing formations; (3) folding of the strata; (4) thickness of sedimentary formations; (5) conditions of deposition.

Jan 1, 1921

By Arthur F. Daily

8.5-1. Bucket Line Dredge. INTRODUCTION. The modern bucket-line dredge for mining placer deposits is a combined floating excavating machine and a gravity concentration system. Material is excavated at the forward end by the buckets, elevated, washed and screened, concentrated for recovery of valuable mineral, and discharged off the stern as coarse and small fractions. The end product is a concentrate consisting either of the valuable mineral(s) and associated heavy minerals, which are taken to a treatment plant on shore; or in the case of gold, a clean amalgam ready for retorting. The bucket-line dredge may be adapted for purposes other than mining for valuable mineral by installing, in lieu of a concentrating system, machinery for pumping all of the solids ashore in a pulp, or for producing washed gravel in selected size fractions of which all or a selected fraction is pumped to disposal areas on shore or into side barges. The two principal types of bucket-line dredges designed for mining are: 1) those having an inclined belt conveyor stacker to discharge the coarse fraction of washed tailing well astern of the hull, and sluices to discharge the sand fraction (Fig. 8.5-1), and 2) those having only sluices for discharge of all tailing astern. Use of the latter type has been confined, with few exceptions, to mining cassiterite-bearing deposits in Malaysia and at sea off Indonesia. Small dredges having only flumes for washing and concentrating all material dug by the buckets have been used for mining shallow stream valley deposits. GENERAL ARRANGEMENT. The general arrangement of a modern bucket-line dredge for mining tin, with a primary concentrating plant on board, is shown in Fig. 8.5-2. The hull and superstructure of most dredges are fabricated of structural steel; wood also has been used for both small and large dredges with complete satisfaction. All-riveted or partially welded unit hulls have been widely used and are desirable for exceptionally severe service. The hull

Jan 1, 1968

By Tripp R. M., C. A. Heiland, Dart Wantland

This paper serves to illustrate the application of geophysics to a virtually abandoned mine properly, an application that led to the discovery of an ore body and thus afforded an Opportunity to cOmpare subsequent geologic findings with geophysical data. The work herein described represents, however: more than mere ''case history." It demonstrates that it is possible to obtain satisfactory results by simple means and relatively inexpericnced personnel. The geophysical surveys were made by students as a part of their field assignments in the course of their regular training, and were supervised by Dart Wantland, J. E. Hawkins and R. Maurice 'Tripp. In the course of several seasons an appreciable amount of material was accumulated, which gave graduate students an opportunity for special studies. In this connection, the contributions by L. Massé, R. C. Hyslop, and J. E. Hawkins deserve special mention. The property owners cooperated wholeheartedly in the work, and special thanks are due messrs. J. F. Johnson and S. E. Zelenkov, of the American Smelting and Refining Co., for their interest and for permission to utilize the results of their development work for this publication. Location and Geology The Malachite mine is situated on the northcrn slope of Bear Creek Canyon, 4 miles northeast of Evergreen, I½ miles northwest of Idledale, and 4% miles west northwest of Morrison, in Jefferson County, Colorado. The location (Fig. I) is north of the center of set. 30, T. 45, R. 70 W., at an elevation of about 7500 ft, above sea level, Near the mine the terrain slopes rather uniformly southward at an angle of about 180 pigs. 3 and 7). The geology of the Malachite mine area has been described by J, underhill,' W, Lindgren,2 and J. Boyd.3,4 A map showing surface outcrops and mine workings appears in Fig, 2. the Malachite mine is in an amphibolite belt enclosed in gneisses and schists of the Idaho-Springs formation (probably early Algonkian age). The highly contorted beds are nearly vertical and strike slightly north of west. A series of granite-pegmatite dikes have been intruded almost at right angles into the gneisses and schists and doubtedless are postmineral. While most of the formations are exposed at the surface, a part of the 'lope is covered by slide rock and float, and in the eastern portion by alluvium and creek fill. A quartz-diorite dike cuts through the amphibolite schists at a small angle with nearly vertical dip. The copper sulphides, developed in this dike by magmatic segregation, occur in lenticular form. As far as the mine workings have revealed, the ore lenses are often discontinuous in depth and

Jan 1, 1946

By J. B. Scuffham, G. I. Warwick, J. B. Lott

The development of solvent extraction processes over recent years has led to their application on an increasing scale in metal extraction plants. The author's company has recently been awarded a contract for the design of the world's largest solvent extraction plant based on pump-mix mixer-settlers. The plant is designed to extract copper from a leach liquor and has an aqueous throughput of 12,000 imperial gpm. The design is based largely upon data obtained from the company's own research laboratories, where work has been undertaken on mixer impeller design, baffle design. settler area, organic entrainment recovery, etc. Investigations have been conducted into the effects of mixer impeller speed, recirculation rates, phase continuity, phase ratio, etc., on extraction efficiency, settler area, and organic entrainment losses. The implications of the results of this work on the design of a large plant using pump-mix mixer-settlers are discussed and the techniques used in overcoming certain scaling problem are outlined.

Jan 1, 1973

By Richard Ageton

SALT bodies in the form of rolls, horses (sometimes called horsebacks), folds, wants and pinches1 have been encountered while driving entries and mining out rooms during the development of the potash mines in New Mexico. Superficially these sporadic salt occurrences appear to be much alike, but closer examination reveals individual characteristics, and after four years of observation it seems possible to divide them into three general groups that may tentatively be called "depositional," "erosional," and "structural." The data collected are not yet sufficient to permit forecasts of their probable location, so that the annoyance of having to mine salt instead of potash could be avoided or lessened. However, the information so far available appears to throw some light on the occurrence of the sylvinite2 bed now being mined, and it is as a progress report that the writer presents the results of his observations. The mines of the United States Potash Co. and the Potash Company of America are about 20 miles northeast of Carlsbad, in Eddy County, N. M. They are on the southwestern flank of the Permian salt basin, which underlies western Texas, Oklahoma and Kansas, south-central Nebraska, southeastern Colorado and eastern New Mexico. The cuttings from many oil wells and the cores from the potash tests drilled in this basin indicate that this salt series approached its greatest thick-ness (about 4000 ft.) in the southeastern part of New Mexico and the adjoining portions of Texas, and that the most advanced stages of

Jan 1, 1936

By William E. Brewster

Dating back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus content, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/6-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a 1/2 factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

By Joseph E. Pogue

In 1920, 531 million barrels of crude petroleum were coi~sumed in the United States. As imposing as this figure is, the fact that the domestic consumption of crude petroleum has increased at an average rate of 10 per cent. a year for the past decade is more striking. Will this rate of increase in demand continue? If so, the year 1930 will call for 1260 million barrels of petroleum—a staggering volume. On the other hand, may we expect the demand for petroleum to grow as rapidly as it did when the automotive industry was having its most phenomenal expansion? If not, to what extent will the growth of oil requirements decrease? When and to what degree will the petroleum industry become affected by the economic law of diminishing returns? Obviously, this matter requires careful analysis, especially as both national and industrial planning must be predicated upon present estimates of the requirements of the future. The purpose of this paper, accordingly, is to project, as closely as present limitations of knowledge permit, the course of the demand for petroleum in the United States over the next ten years. At first, the problem of estimating the future of a demand as complex as that for petroleum might appear insoluble. Fortunately, hon~ever, therc are several scientific methods of approaching the problem, centering around a study of rates of industrial growth, which lend considerable hope that the requirements of the immediate future in this field may be approximated with sufficient closeness to have practical value as a basis of action. Growth oF Petroleum Demand The demand for crude petroleum is the resultant of the demands for the products made jointly from this substance—gasoline, kerosene, gas and fuel oil, and lubricating oils. The demands for these have grown at

Jan 1, 1923

By L. J. Ebert, G. Sachs, W. F. Brown

Isothermal transformation, or "aus-tempering," of a carbon-containing aus-tenite at elevated temperatures yields so-called "intermediate products." Their structure and properties are, for a given hardness, rather different from those of "tempered martensite" obtained on conventional quenching and tempering.' Several investigators2,3 have found that for high carbon and slightly alloyed steels the intermediate products formed at temperatures close to that of the martensite reaction possess strength properties superior to those of tempered martensite. The structure of these low temperature, intermediate products is generally acicular (bainite) but clearly different from that of martensite. However, at higher austempering temperatures, between 1000 and 1300°F (540 and 700°C) carbon steels were found to exhibit a rather low ductility.4,5 Thus notch bar tensile tests showed the ratio between notch strength and regular tensile strength to decrease with increasing austempering temperature. For ductilities below a few percent this notch strength ratio is a measure of ductility, according to investigations on low alloy steels.637 Furthermore the presence of intermediate products formed unintentionally on quenching was considered as responsible for the low ductility and impact energy of some heat treated steels,8 These intermediate products could result from partial transformation at the so-called "nose-temperature" where the rate of the transformation is a maximum. Tempering improved such mixtures of martensite and intermediate products, their properties approaching those of tempered martensite of equal hardness. The following investigation constitutes an attempt to determine certain strength properties of a partially austempered and subsequently quenched low alloy steel, namely, a chromium steel (SAE 5140) The structures formed by such a treatment should consist of a mixture of intermediate products formed on austempering and a martensite formed on oil quenching from the austempering temperature. It was intended, by varying the austempering time, to vary the quantity of the intermediate products between zero and 100 pct. The austempering temperature of 860°F was selected after extensive preliminary tests close to the nose-temperature. Austempering at this temperature yielded an acicular intermediate product. .Additional tests under less exacting conditions were made for an austempering temperature of 950°F where the intermediate product appeared to be very fine pearlite. To determine the effects of tempering on structures containing various amounts of

Jan 1, 1949

By Paul Giesecke

Since most modern metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with- the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. Principles of Spectrochemical Analysis In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, * visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1947

By J. D. Livingston, J. J. Becker

A MAJOR difficulty in the experimental study of precipitation-hardening is the measurement of particle sizes too small to be easily resolved with the microscope. It has been shown recently, however, that magnetic measurements on copper-cobalt al- loys in the aged state can be used to determine the average volume, total volume, volume distribution, and shape of the ferromagnetic cobalt-rich particles, even though the particles are submicroscopic in size. r' These alloys also are known to exhibit considerable precipitation hardening. This paper reports some results on the dependence of the mechanical properties of such an alloy on the particle size, determined magnetically. It further illustrates the use of other magnetic measurements in interpreting structure changes occurring during deformation.

Jan 1, 1959

By H. E. Nold

ThE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained. For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. Periodic Kilns Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues throughout the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1934

By G. Sachs, L. J. Ebert, W. F. Brown

Isothermal transformation, or "aus-tempering," of a carbon-containing aus-tenite at elevated temperatures yields so-called "intermediate products." Their structure and properties are, for a given hardness, rather different from those of "tempered martensite" obtained on conventional quenching and tempering.' Several investigators2,3 have found that for high carbon and slightly alloyed steels the intermediate products formed at temperatures close to that of the martensite reaction possess strength properties superior to those of tempered martensite. The structure of these low temperature, intermediate products is generally acicular (bainite) but clearly different from that of martensite. However, at higher austempering temperatures, between 1000 and 1300°F (540 and 700°C) carbon steels were found to exhibit a rather low ductility.4,5 Thus notch bar tensile tests showed the ratio between notch strength and regular tensile strength to decrease with increasing austempering temperature. For ductilities below a few percent this notch strength ratio is a measure of ductility, according to investigations on low alloy steels.637 Furthermore the presence of intermediate products formed unintentionally on quenching was considered as responsible for the low ductility and impact energy of some heat treated steels,8 These intermediate products could result from partial transformation at the so-called "nose-temperature" where the rate of the transformation is a maximum. Tempering improved such mixtures of martensite and intermediate products, their properties approaching those of tempered martensite of equal hardness. The following investigation constitutes an attempt to determine certain strength properties of a partially austempered and subsequently quenched low alloy steel, namely, a chromium steel (SAE 5140) The structures formed by such a treatment should consist of a mixture of intermediate products formed on austempering and a martensite formed on oil quenching from the austempering temperature. It was intended, by varying the austempering time, to vary the quantity of the intermediate products between zero and 100 pct. The austempering temperature of 860°F was selected after extensive preliminary tests close to the nose-temperature. Austempering at this temperature yielded an acicular intermediate product. .Additional tests under less exacting conditions were made for an austempering temperature of 950°F where the intermediate product appeared to be very fine pearlite. To determine the effects of tempering on structures containing various amounts of

Jan 1, 1949

By Alden H. Emery, J. J. Forbes

The data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in six coalmining states. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand and transporting it from the working face to the surface. The data thus obtained were considered from two angles; namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be made to discuss the former factor in this paper. ConDitions of Mining The mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. All of the coal mined was bituminous, from beds 30 to 120 in. thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by shortwall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face wets done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal were commonly used, although some roof work was done with jack-hammers and a little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1800 to 3600lb. With few exceptions, coal was won at the face by dry methods, that is to say, no water was employed for wetting down the dust either during undercutting, loading or transportation. Observations of Sources of Dust The common sources of coal dust as observed, arranged by decreasing amounts, were as follows: (1) Undercutting with mining machines; (2)

Jan 1, 1927

By A. L. Holley

THE application of scientific methods to the investigation of natural laws and to the conduct of the useful arts which are founded upon them, is year by year mitigating the asperity and enlarging the outcome of human endeavor. More notably, perhaps, are these the facts in that system of productive and constructive arts of, which engineering is the general name. In metallurgical engineering especially, within the period of our own recollection, how rapid has been the rate and how wide the scope of progress: the scientific discovery and mining of metalliferous veins; the economical separation and reduction of ores of every grade; the production and regulation of high temperatures; the varied improvements in the manufacture of iron, in saved heat and work, in uniformity and range of products ; and, most important of all, the creation and the utilization, to be counted by the million tons a year, of the cheap constructive steels. Wonderful as this range and degree of development may appear to the public eye, the close and thoughtful observer must, nevertheless, conclude that neither the profession nor the craft of engineering may congratulate themselves too complaisantly, but that they should rather acknowledge to each other the embarrassing incompleteness of the union between engineering science and art. There is a small school of philosophers whom we may designate as original investigators, men who come close to nature, who search into first principles, and who follow that scientific and therefore fruitful method by which the relations of matter and force are discovered, classified, and brought within the reach of practice. These wonderful - men do not indeed create the laws of nature, as they sometimes almost seem to, but they go up into the trembling mountain and the thick darkness and bring down the tables upon which they are written. * President's Opening Address. The discussion following this paper, and also the Joint Discussion of the Institute and the American Society of Civil Engineers, on the subject of Technical Education., are published in a separate volume.

Jan 1, 1876

By Henry A. Ley

Kansas ranked fourth on the list of oil-producing states during the year 1930. Progressive statistics show that total production for the year will approximate 42,729,085 bbl. When final figures are compiled for Kansas the production may exceed this estimate, and thereby threaten the all-time record of 43,253,470 bbl. in 1918. Throughout the year the cumulative volume of potential drilled-up production has been increased by new discoveries and by extensions to proven areas in the territory west of the Nemaha (granite ridge) Range. Scattered drilling and leasing operations of a constructive nature occurred, but completions declined to the lowest levels in more than 11 years. Average initial production of current completions climbed to a new all-time high of 512 bbl. to the well. Proration measures were applied to the flush pools. The resulting shut-in potential production, as of December 15, is estimated at 110,000 bbl. This estimate is a wild guess. If all wells of the state were permitted to flow wide open for a period of six months production would not exceed 150,000 bbl. a day. The outstanding development of the year was an intensive drilling campaign in southwestern Kansas, which contributed at least 1,000,000 acres of contiguous natural-gas lands to the natural-gas resources of the United States. Production and Development Prospecting for oil in Kansas began shortly after the initial prospecting at Titusville. Operations and interest in the potentialities became active about 1870. This development was restricted to the shallow districts of northeastern Kansas. By 1895 operations had extended southward to the Oklahoma state line and sufficient prospecting had taken place to prove the potentialities of the state. Active prospecting was extended westward by the discovery of oil on the Nemaha Range in Butler County about 1916. The discovery of oil in Russell County added an extensive borderland province in 1923. The important discoveries of oil in Sedgwick County revived interests and operations throughout this territory in 1928. The development of widespread natural-gas lands in extreme southwestern Kansas during 1930 carried active exploration to the western boundary of the state.

Jan 1, 1931

By Charles Behre

UNDER the caption "fault," geologists intend to include all mass movements of solid rocks over adjacent rock masses. When these are studied long after their origin, however, circumstances make it possible to recognize as "fault" only formations showing clear evidence of actual movement of one side with' respect to the other. Necessarily the chief evidence consists of the offset of a vein, bed, or other key structure. Planes of movement parallel to the bedding; or nearly so, are recognized with difficulty or are overlooked and hence many important faults are wholly unrecorded. Indeed, among standard American references on structural geology, one alone emphasizes the importance of bedding-plane movements and that' one only briefly1. For some time the writer, cognizant of this difficulty, has paid special attention to such movements, both as observed in the field and as recorded in the literature. It is believed that enough data are now at hand to justify a short-discussion. Its purposes are fivefold. It is desired first to briefly classify and describe at least the more common kinds of bedding-plane faults, and second, to examine the causes and manner of their formation, at least in instances where the subject has not yet been well covered by other investigators. Third, certain by-products of bedding-plane movements are of such conspicuous importance to the economic geologist and mining engineer as to merit mention. Fourth, concrete illustrations should be placed before the reader in order to lend reality and to furnish a basis of comparison with his experience; such illustrations will necessarily be scattered through the text of this paper. They' are only in part from the writer's own field observations. The fifth and prime objective of this paper is to direct attention to the great importance of movements on the bedding planes, in the hope that the recognition of such movements and their significance may simplify mining problems.

Jan 1, 1937

By H. T. Matson, G. Allan Wallis

In the Northern Rhodesia copper fields the size of the orebodies and the exceptionally consistent values over great distances made it possible to outline the ore with drill holes spaced at 1000-ft. intervals; in some cases, 2000-ft. intervals. Owing to the fact that the size of the deposits made it very evident that much outside capital would have to be called in to develop them and, owing to the wide spacing of the holes, it was essential that the sampling of drill holes be as accurate as possible, so that outside examining engineers could adopt the results as trustworthy within the limits of accuracy of the drilling method. With this object in view, the field staffs of the Selection Trust group of companies have studied for the past three years, and are still studying, drill sampling in a very thorough manner, and for this reason it is felt that these notes may be of interest to engineers or students who are, or in the future may be, in charge of drilling operations. The orebodies in this field lie in shales and sandstones, more or less indurated, in the lower strata of the Roan series, and the copper mineralization is in the form of sulfides predominantly, with some oxidized copper minerals. These interested in the geology and history of the area can find full details in a recent paper by Anton Gray and Russell J. Parker.' In some formations core recovery was good—between 90 and 100 per cent.—and where any difficulty occurred in recovering sludge, as in fissured ground, this was not insisted upon; but the samplers' difficulties, both practical and theoretical, do not commence until core recovery drops and sludge recovery becomes important, for if core is being ground up it is recoverable only as sludge, and naturally the sludge sample, which theoretically should contain only the material cut from the annular ring around the core, is being salted, in a sense, by the ground-up core. In the perfect core, where 100 per cent. core is recovered as well as 100 per cent. sludge, the two samples can be treated separately, as in the case

Jan 1, 1931

By H. H. Dievendorff, F. W. Hertel

The method of drilling deep wells into the earth for the recovery of oil and gas is beset with many hazards. This is especially true in the Ventura Avenue field, which has the distinction of being the hardest field in California in which to complete a deep well. The hard, shifting and squeezing formations must be penetrated to great depths in the face of tremendous gas pressures. This field presents problems that keep the operators abreast with all of the latest developments in oil-field tools and machinery and in oil-well drilling practices. Equipment must be strong, and adapted to deep-well drilling and the handling of long heavy strings of casing. High-pressure sands require the utrnost care and attention of the operators and no chances can be taken, since a serious blowout may cause the loss of a well that has cost months of labor and expense. Equipment must meet these requirements or be discarded. Although the deepest wells in the world are not in this field, nor hav:. the longest strings of casing been set, nevertheless, the consistency with which deep wells are drilled and long strings of casing are set places the Ventura Avenue field foremost, in this respect, among the oil fields of the world. The V'entura Avenue field dors claim the deepest commercial oil-producing well in the world, in the Shell Co. of California's "Edison" No. 18. This well was drilled 7015 ft. and came in flowing 3280 bhl. of oil per day. This field also claims the deepest average depth of producing wells in that its Ill producing wells average 5676 ft. in depth. Of these 111 producing wells, 50 arc 6000 ft. or deeper, and 16 are 6500 ft. or deeper. Also, of the 111 producing wells 100 arc flowing, and 11 arc pumping wells. This paper is intended to set forth the methods used in the drilling of deep wells with rotary tools and the handling of long heavy strings of casing in the Ventura Avenue field.

Jan 1, 1928