Search Documents

By A. N. Mitinsky

Discussion of the paper of A. N. MITINSKY, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1697 to 1705. LAWFORD H. FRY, Burnham, Pa. (communication to the Secretary*). -The author assumes that the proportional limit and the elastic limit are coincident or very nearly so, and then further assumes that the stress corresponding to these two points is the least stress which if repeated will cause failure. The point is extremely interesting and it is to be regretted that the author did not quote experimental data to show the relation between the limit of repeated stress and the other properties of the material. The author's suggestion that a steel of poor quality may have a normal value for the yield point and tensile strength (see Fig. 2) and an abnormally low elastic limit, and that this will correspond to a low resistance to repeated stress, may account for a number of failures of axles in which the tensile tests show normal physical properties. If so and if a determination of the proportional limit would have eliminated the material before it was put into service, this determination will merit most earnest attention. It appears, however, that considerable further research is necessary before any definite conclusion as to the quality of a steel can be drawn from its proportional limit. Mr. Mitinsky's paper is extremely interesting and if it stimulates thought and work along the lines indicated, it may prove of considerable practical benefit. H. V. WILLE, Philadelphia, Pa.-The paper discusses the difference between the proportional limit, or elastic limit, and the yield point, and refers to the fact that much harm results from confusion of the terms yield point and elastic limit. Similar confusion has arisen in this country; the American-Society for Testing Materials does not even consider the elastic limit and proportional limit to be identical and recently adopted the following definitions:

Jan 12, 1915

By Robert Glass Cleland

THE THIRD and most important item on the Phelps Dodge agenda for the development of new ore supplies involved the site of the company's initial venture into Arizona, the old mining camp of Morenci. By the purchase of the Arizona Copper Company's holdings in 1921, Phelps Dodge had obtained control of virtually the entire Morenci district, including town, public utilities, and, above all, the huge mineralized area that had once been divided between numerous competing companies. Because of this rigid concentration of ownership in the hands of one organization, Phelps Dodge was able to plan and successfully carry out a program of greater magnitude than any Arizona mining company had previously under- taken. The immense deposit of low-grade ore, usually referred to as the Clay Orebody, had been known to the mining companies of Morenci for many years. Pioneer exploratory work, both by the Arizona Copper Company and later by Phelps Dodge, revealed that the deposit, mostly of light-gray porphyry rock, lay under a hard capping from two hundred to five hundred feet thick. An intensive drilling

Jan 1, 1952

By K. B. Nowels

The attainment of efficient flooding to a large extent depends upon a knowledge of fluid movement through porous media and the pressures used in controlling this movement. Little has been understood con-cerning the fundamental principles involved in the forced drive of water-flooding and an attempt will be made to present some data which may be of interest. Considerable data and technical information pertaining to natural and artificial water-flooding have been presented in the past by Torrey, Umpleby, Fettke, Panyity and others. Their papers have thoroughly covered the description of past and present-day methods of oil recovery by flooding in the Bradford field, especially an article by Torreyl in the Petroleum Engineering Handbook. A bibliography of papers devoted to watcr-flooding, published in Mr. Torrey's article, is appended to this paper. No attempt has been made, therefore, to describe the installations and procedure necessary in flooding, thus permitting the writer to deal exclusively with the mechanics of water movement in flooding operations and its relationship to well spacing. Artificial water-flooding will probably always be the most successful in oil fields described by Herold as being under "capillary control"" and will probably be useless in fields naturally under hydraulic or volumetric control. The natural water drive in an oil field under either of these two controls may give efficient recoveries, as a result of the regulated encroachment of edge water. Such a "natural flood" resulting from the influence of edge water must not be confused with the term as used in this paper, however. Any reference to "natural flood" will here refer to the old method of flooding formerly used in the Bradford field. This was discovered largely by accident and utilized the hydrostatic pressure created by a column of water standing in a watered-out oil well in forcing the oil to an adjacent producing well. The same principles are involved in either natural or artificial flooding, and the latter method simply

Jan 1, 1933

By Robert P. Burrows

In preparing this paper the object has been to set forth facts relating to illumination problems, which, judging from the results realized in the iron and steel and other industries somewhat similar to mining, will tend toward furthering safety, production, and contentment of employees, as well as economy of operation in mines. By applying the principles of illumination with the assistance of modern appliances, the full benefits in efficiency may be derived from improvements already made in other details of mine operation. The lighting of a typical coal mine may be*divided into four distinct parts: 1, The lighting of the buildings about the top; 2, the lighting of the working faces; 3, general illumination at the bottom; and 4, special applications of lighting. The lighting of buildings about the top may be treated in the same manner as that of any other industrial plant, for we have a boiler room, an engine and generator room, a forge, a machine shop, and a hoist room. These can be well and efficiently lighted by the use of 100-watt tungsten-filament multiple lamps with proper reflectors so spaced and suspended that a power consumption of from ¼ watt per square foot in the boiler room to 1 watt per square foot in the machine shop is obtained. The methods that apply to this kind of lighting have been ably treated by a number of authors,' and for this reason a detailed discussion is unnecessary. The lighting of the working faces is usually done by means of portable lamps, of which there are four types in use: The oil torch, the acetylene Iamp, and the oil and the electric safety lamps. The different types have been fully described in numerous papers and articles and will not be covered here, although a few figures on the cost of operation will no doubt be

Jan 1, 1916

By Guido Del Giudice

THE term "slime-coating" is not new in the art of flotation; the phenomenon has been observed and described by Taggart;(1)? Taggart, Taylor, and Ince;(2) and by Ince.(3) Notwithstanding that flotation was introduced for the treatment of finely crushed ore, the adverse effects of slimes have been recognized since the earliest days of the process, and the Elmore, Delprat, Potter, and other processes actually specified desliming of the ore prior to treatment. The cause of this trouble has been studied and described by Taggart;(1) Taggart, Taylor, and Ince;(2) Ince; 3 Morrow and Griswold;(4) and by Gaudin and Malozemoff.(5) OLD THEORY OF SLIME-COATINGS At present, so far as published work shows, there seems to be but one theory for the mechanism of slime-coatings. Ince(3) states that they are due to attraction between electrostatic charges of opposite sign on the sulfide and, on the slime particles, supporting this theory by migration experiments in the Burton tube. He also used the microscope in conjunction with a glass cell employed by Beans and Eastlack(6) in studying migration, but met with interference from endosmosis. Several attempts have been made in the Department of Mineral Dressing at Columbia University to duplicate Ince's experiments with the Burton tube, but the results have never been convincing. Formation of precipitates which settled through the pulp levels, and evolution of gas at the electrodes, which disturbed the interface between the pulp and the distilled water above it, seriously interfered with observations. However, by use of the migration cell shown in Fig. 1, endosmosis effects and the disturbances due to precipitation and gas evolution were avoided, and distinct and reproducible migrations or absence of migration were observed.

Jan 1, 1934

By L. E. Paulson

INTRODUCTION The Northern Great Plains has 16 billion tons of strippable lignite (1). Presently, 15 million tons per year are mined; essentially all is used for generation of electrical power. In the future, additional large quantities will be consumed in the production of gaseous and liquid fuels. A major consideration in design and operability of power stations and conversion plants is the nature of the ash or inorganic constituents of the lignite used. These inorganic components cause fireside fouling in boilers, exert a catalytic effect in liquefaction and gasification, and contribute to particulate and SO2 emissions. Ash fouling on fireside boiler tubes cause reduced heat transfer and gas flow which limits boiler performance. Severe fouling can result in shutdown of the boiler. A comprehensive test program in both pilot plant and field studies at the Grand Forks Energy Technology Center (GFETC) has shown that ash fouling increases with increased sodium content of low-rank coals (2). The sodium in the coal can be

Jan 1, 1983

By Donald L. Birkimer

GENERAL INTRODUCTION To paraphrase comments made by Black and Hoek(1) on the status of rock mechanics, the general methods of applied science related to rock mechanics are: a. Observe the phenomena of nature as they occur and, wherever possible, quantify the observations. b. Propound a model or theory to explain the phenomena observed. c. Test and develop the theory by further experimentation in the laboratory and in the field. d. Use the theory developed to predict behavior in similar or extended circumstances. e. Insure by measured experiment and observation that the predictions made are valid, or that deviations from the predicted behavior can be accounted for. f. Modify the theory and practice as necessary, and continue the process until more general laws can be formulated and applied, with a useful degree of confidence, to practical problems. This paper will present an infant concept. It will, in fact, propound a possibly useful theory to help explain commonly observed phenomena. It will test and develop the theory for a material similar in nature to some rocks. It will be used to predict behavior in the extended circumstances of a

Jan 1, 1971

By Edward B. Durham

At the Richmond mecting in February, 1901, I presented for discussion the proposed rail-specifications of Committee No. 1 of the American Section of the International Association for Testing Materials, with a review of their work, and other matters relating to the heat-treatment and chemical composition of steel (Trans., xxxi., 455). In order to bring out the views of our members on the important points referred to, I offered for discussion the following questions and comments (trans., xxxi., 972): " 1. The advantages to be gained by using more metal in the flanges and web of the heavier sections of rails.

Jan 1, 1903

By Michael Perch, Charles C. Russell

Nearly 75 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank' standardized by the American Society for Testing Materials. Although this method of classification has been an American stand¬ard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1944

By R. A. Greenkorn, R. C. Smith

Hele-Shaw cells are used to model creeping flow through porous media (where Darcy&apos;s law is valid). The effects of inertia on flow about obstructions in a Hele-Shaw cell can be calculated by a perturbation method if one can determine a solution to Laplace&apos;s equation. Results of a computer solution for flow about circular, square and elliptical obstructions are presented. These results show that or a modified Reynolds number of less than I, the inertia terms are small; and for values of less than 3, the average streamline predicts the ideal flow. Therefore, the analogy might be used for studying flow in porous media up to a modified Reynolds number of at least 3. INTRODUCTION The nature of fluid flow in porous media is of interest in the fields of soil mechanics, ground water flow, petroleum production, filtration and flow in packed beds. Because it is very difficult to study the phenomenological behavior of flow in porous media, homologs and analogs are used to study flow characteristics. A Hele-Shaw model, made of two closely spaced plates - usually glass — is often used as an analogy to two-dimensional flow in porous media. Hele-Shaw2 showed experimentally that the streamline configuration for creeping flow around an obstacle located between two closely spaced parallel plates is the same as for two-dimensional, ideal flow about the same obstacle. Stokes7 verified these observations mathematically. The usual equation of motion for flow in porous media is Darcy&apos;s law. The form of the mathematical statement of Darcy&apos;s law is identical, within a multiplicative constant, to the expression for the average velocity over the plate gap in the plane of a Hele-Shaw model. These models may be used to describe flow in both homogeneous and heterogeneous porous media. In the mathematical proof of the Hele-Shaw analogy it is assumed that the convective terms in the Navier-Stokes equations are negligible and that the equations of motion degenerate to Laplace&apos;s equation, with pressure the dependent variable. Whenever a Hele-Shaw model is used as an analogy to flow in porous media, .the validity of this assumption is in question. Riegels5 showed that if convection is not neglected, the velocity distribution around a cylindrical obstruction in the flow field depends on a Reynolds number, the plate spacing, and a dimension characteristic of the obstacle. Riegels&apos; solution, a perturbation solution, uses the boundary condition that the flow rate into the obstacle averaged over the plate gap at any point on the obstacle is zero. The method requires that a solution to Poisson&apos;s equation for the perturbation pressure be found. Riegels evaluated this solution for the case of the cylindrical obstruction. His method may be simplified by eliminating the need for solving Poisson&apos;s equation for the perturbation pressure. Instead, an analytic expression for the perturbation pressure gradient is obtained (valid for arbitrary shapes) and used to eliminate pressure from the equations for the perturbation velocities. The results show, for symmetrical shapes, that if NRe < 1, the convective acceleration terms are small, and that the average velocities represent ideal flow up to at least NRe = 3, where: L is a characteristic dimension of the obstacle perpendicular to flow, b is the plate spacing, u is viscosity, v, is velocity of approach and p is density. THEORY* Incompressible fluid flow through a Hele-Shaw model and a porous medium are analogous because the equations for the average velocity components in two-dimensional flow are identical if:

Jan 1, 1970

By B. P. Mulcahy

When the phrase "selection of coal for carbonization" is used, there is always the implied continuance of thought "to make good coke.&apos;&apos; The reason for this, of course, lies in the fact that, in almost all instances, when coal is carbonized coke is the principal product. Under certain conditions the yield of gas may also be a factor, but even here it must be secondary to the coke yield, for in every instance coke represents the largest single product of the process. The importance of coke to the byproduct industry has been considerably enhanced during the past 20 years because of the continuously decreasing financial returns of all the by-products. This fact will account, in part, for the rebirth of interest and investigation in the carbonization process during the past 10 years. Many papers have been written on this subject, with naturally divergent thoughts because of the diversity of interests, but in each instance the common aim was the same—the making of better coke. Scope of Investigation In perusing this literature, the writer was struck with the constantly recurring imposed condition of asking for better coke, but with the distinct unwillingness to make any concession to temperature of carbonization. When there is a high demand for coke, the only means by which the industry can increase the quantity is to shorten the coking time by an increase in temperature, or to increase the quantity of low-volatile coal, or both; and since in many instances the percentage of low-volatile coal can be increased only in small quantities, because of factors to be discussed later, the big increase must come from shortening the coking time. When this is done most of the improvement accomplished by the selection of the coals in the mixture is lost. It is not felt necessary in this paper to discuss the advantages of minimum ash and sulphur and other materials in coal. The value of minimum contents of these materials in coke is well established. When the use of coals high in these contents is dictated, the selection of coals, as we will consider it here, cannot apply to full advantage. The scope of this paper, then, will be to discuss the factors of inherent coal characteristics and operating procedures that influence coke quality, for they are fundamentally related and both must be considered if we are to attain our objective of better coke. A study of either must embrace a study of both simultaneously. To properly evaluate the influence of the coal and to help in the selection, we must first be able to appraise the coke, and interpret fairly the influence of the process in all of its aspects. Appraisal of Coke To refer simply to the quality of coke gives no indication of what is meant, for the term is too general in its implication. An analysis of a coke is divided usually

Jan 1, 1944

By L. J. M. Smits

A theoretical equation is developed describing membrane potentials of shaly sands as a function of the cation-exchange capacity per unit pore volume of the rock and saturating water salinity. This equation is based on the same simple physical model as that employed earlier7 describing the electrical conductivity of shaly sands. Experiments conducted with NaCl solutions showed that the equation is obeyed, except in the case of saturated salt solutions where minor deviations were observed. A possible explanation is given for this discrepancy. As the clay content and the porosity of shales may vary appreciably, shale membrane potentials also vary. It was found that membrane potentials of shales can be calculated accurately with the aid of the same theory. Consequently, changes in membrane potentials can be accounted for by simple measurement of cation-exchange capacities per unit pore volume of both shales and shaly sands. Charts are given to facilitate interpretation of the electrochemical part of the SP in terms of cation-exchange capacities and the salinities of mud filtrate and formation water. INTRODUCTION A spontaneous potential (SP) log is a record of the way in which the electrical potential of a sonde varies as it passes down a borehole. Such variations frequently reflect rock texture, e.g., permeable beds intercalated in an impermeable series often are indicated by a sharp change in potential. Nowadays it is recognized that SP logs may be interpreted in terms of formation-water salinity and formation shaliness. The four sources of the SP are illustrated in Fig. 1. El and E4 represent streaming potentials generated by the flow of mud filtrate through mud cake opposite permeable formations and through shale, respectively. An extensive review of the literature on the evaluation of these streaming potentials is given by Lynchl and will not be discussed here. The remaining part of the SP generally is called the electrochemical potential, which is divided into two parts: a membrane potential across the shale (E3, Fig. 1) and a membrane potential in the permeable sand at the diffusion boundary between formation water and mud filtrate (E2, Fig. 1). It was found by wyllie2 that the membrane potential across the shale, E3, is the most important contribution to the electrochemical potential, the shale acting as a semi permeable membrane. When the sand is clean it does not influence the diffusion process, so E2 equals the value of the so-called liquid-liquid junction potential observed when the two solutions diffuse freely into each other. When the sand contains clay, however, this interferes with the diffusion process and affects the diffusion potential generated. The greater the proportion of clay, the stronger this effect will be. Wyllie,3 Doll4 and Poupon et al.5 took this effect into account theoretically, starting from a physical

Jan 1, 1969

By B. P. Mulcahy

When the phrase "selection of coal for carbonization" is used, there is always the implied continuance of thought "to make good coke.&apos;&apos; The reason for this, of course, lies in the fact that, in almost all instances, when coal is carbonized coke is the principal product. Under certain conditions the yield of gas may also be a factor, but even here it must be secondary to the coke yield, for in every instance coke represents the largest single product of the process. The importance of coke to the byproduct industry has been considerably enhanced during the past 20 years because of the continuously decreasing financial returns of all the by-products. This fact will account, in part, for the rebirth of interest and investigation in the carbonization process during the past 10 years. Many papers have been written on this subject, with naturally divergent thoughts because of the diversity of interests, but in each instance the common aim was the same—the making of better coke. Scope of Investigation In perusing this literature, the writer was struck with the constantly recurring imposed condition of asking for better coke, but with the distinct unwillingness to make any concession to temperature of carbonization. When there is a high demand for coke, the only means by which the industry can increase the quantity is to shorten the coking time by an increase in temperature, or to increase the quantity of low-volatile coal, or both; and since in many instances the percentage of low-volatile coal can be increased only in small quantities, because of factors to be discussed later, the big increase must come from shortening the coking time. When this is done most of the improvement accomplished by the selection of the coals in the mixture is lost. It is not felt necessary in this paper to discuss the advantages of minimum ash and sulphur and other materials in coal. The value of minimum contents of these materials in coke is well established. When the use of coals high in these contents is dictated, the selection of coals, as we will consider it here, cannot apply to full advantage. The scope of this paper, then, will be to discuss the factors of inherent coal characteristics and operating procedures that influence coke quality, for they are fundamentally related and both must be considered if we are to attain our objective of better coke. A study of either must embrace a study of both simultaneously. To properly evaluate the influence of the coal and to help in the selection, we must first be able to appraise the coke, and interpret fairly the influence of the process in all of its aspects. Appraisal of Coke To refer simply to the quality of coke gives no indication of what is meant, for the term is too general in its implication. An analysis of a coke is divided usually

Jan 1, 1944

By F. W. Schroeder

AT the annual meeting of the Institute 2 years ago, a paper,1 " Requirements of Refractories for Open Hearths," was presented by F. W. Davis and G. A. Bole of the U. S. Bureau of Mines. In a brief foreword, D. A. Lyon stated that the paper was not to report the results obtained but rather to present an outline to serve as a basis for discussion. The essential parts of an open-hearth furnace were described and the conditions under which they operate. Some constructive discussion followed the reading of the paper. One of the first fellowship investigations undertaken by the Bureau of Mines in 1924 under the cooperative agreement with Carnegie Institute of Technology, through the Metallurgical Advisory Board, was to determine service conditions of open-hearth refractories. The present paper gives the results of this work which was done in the Pittsburgh district and was in charge of the authors. Material contributions in the form of data were contributed by E. N. Bauer, J. W. Campbell, G. H. Pfeiffer and A. Grodner, Carnegie Institute of Technology research fellows. The study covered 18 mos.

Jan 7, 1926

By J. M. Flaitz, A. S. Parks

OF the various methods of sampling gas-condensate wells, a method that secures a continuous representative sample of the well stream is desirable. Such a method, consisting of a sampling tube introduced into the well tubing, has proved satisfactory. The method is sufficiently accurate for operating and engineering problems. A portable testing apparatus can be used with the sampling tube to obtain data useful in studying the economic and technical aspects of the development and operation of gas-condensate properties. INTRODUCTION The recent discovery and development of gas reserves that contain hydrocarbons that condense with reduction of temperature or pressure, or both, to form a product known as condensate, has brought many new problems to the oil and gas industries. With further discovery of deep, high-pressure fields it is presumable that many more gas fields of this type will be added to the steadily increasing number. Such gas reserves are found either associated with oil as a gas cap or in separate formations. There seems to be no positive correlation between the physical or geological nature of the reservoir, and the chemical composition or phase characteristics of its contents. Knowledge of the chemical make-up and phase behavior of gas-condensate reserves are needed to cope with many problems. A knowledge of the chemical composition and phase characteristics of the reservoir material is necessary to properly design a gasoline or recycling plant, to estimate natural gas and condensate reserves, to enable the operator to study the economic and technical aspects of various methods of operation and development, and to carry out the plan of operating subsurface and surface lease equipment. This information is often useful in questions of mineral ownership, proration, legal position, and taxation. It is the purpose of this paper to discuss methods used by the writers to determine the chemical composition and phase characteristics of the fluids produced from a condensate well. The scope of the paper includes a discussion and description of the method of sampling, the results of tests on the accuracy of the sampling method, a description of a portable testing apparatus used to examine the phase characteristics, typical results of tests on wells from several condensate fields, and some of the applications of these data to production problems. References to previous work on this subject are cited at the end of the paper. THE PROBLEM At reservoir conditions of temperature and pressure, the fluids produced from a condensate well exist in a homogeneous vaporous condition. The consequent reduction of temperature and pressure that occurs as this gas enters and flows up the well tube results in condensation of some of the hydrocarbon material to form a liquid. The relative amount of liquid condensed at any point in the flowing system

Jan 1, 1941

By William C. Alden

A great landslide occurred on June 23, 1925, in the valley of Gros Ventre River, about 35 miles south of Yellowstone National Park (Fig. 1). The relations of the north-easterly dipping rock formations of the slide scarp and of the dam formed by the slide are shown in the diagrammatic cross-section of the valley (Fig. 2). This generalized section is based on unpublished maps and notes by Eliot Rlackwelder, in the files of the IT. S. Geological Survey. Heavy rains and melting snow in the Gros Ventre Mountains had saturated clay layers in the Carboniferous strata, which dip toward the valley at angles of 18" to 21°, consequently an enormous mass of rock at the end of the north spur of Sheep Mountain became loosened and, on the afternoon of June 23, slid suddenly down into the valley. Within a few minutes this mass of debris—estimated as 50,000,000 cu. yd.—carrying

Jan 1, 1928

By E. O. Wagner, V. F. Parry, W. S. Landers

Following investigations by the Denver Bureau of Mines on drying fine coal in the entrained state, Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help off- set the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee, and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal, but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used.

Jan 1, 1956

By Bernard Moore

AT present the demands of the United States for strontium are met by imports from Germany, England and Canada, which vary considerably in proportions of ore and finished salts, in tonnage and in value. Statistics for the period 1926-1932 are given in Table 1. Domestic deposits are TABLE 1.-Strontium Imported into the United States, 1926-1932a Ore Chemicals Year Short Tons Value Pounds Value 1926 2,200 $58,159 5,433,044 $115,436 1927 1,356 58,711 4,233,816 149,383 1928 759 31,157 3,380,464 136,561 1929 973 45,505 4,578,327 196,233 1930 220 10,459 2,153,788 104.807 1931 (260 lbs.) 123 1,742,714 83,564 1932 5 276 469,481 20,910 a Mineral Industry (1934) 42, 61. known in many states, but the, larger and purer ones are in the West, particularly in the desert region of southeastern California and western Arizona. These deposits are large enough to command interest, par-ticularly in consideration of future cheap power at the Boulder Dam. The deposits described in this paper were examined during an investi-gation of the mineral resources of the Boulder Dam region by the United States Geological Survey for the United States Bureau of Reclamation in the spring of 1934. Mr. D. F. Hewett, who had general charge of the investigation, Mr. W. T. Schaller and Mr. M. I. Goldman contributed many helpful suggestions. Mr. N. H. Harshman assisted efficiently during the field work.

Jan 1, 1935

By Frank H. Probert

The mining laws relating to winding-ropes in some of the German provinces are very strict, and severe tests have to be periodically made to see that the ropes in use come up to the prescribed standard. A few notes on the method of testing the ropes and the results obtained may be of interest to the members of the Institute. Permission must be given by the Inspector of Mines to put up a winding-plant; and previous to installation a full report made by the manager, clearly setting forth all details of the shaft, the pit-head, engines and appliances appertaining thereto has to be sent to the mining officials. Accompanying each subsequent report, further details, such as the name of the firm supplying the rope, construction, quality of steel, date of installment, weight per meter, length, particulars of the safetycatches, cages, etc., must be given. At least one spare rope must be kept at ever? shaft ready for use in case of emergency. The rope must hang in the shaft, with cage attached, not less than twenty-four hours before it is used for winding; and it must have undergone a severe test in the manner hereafter described. The laws prescribe that when a rope is continually in use it must be tested every three months; but if the rope is only used every few days it must be tested at least every six months, in the presence of the superior officer; and notification of the date of testing has to be sent to the Bergrath two days before the test is made, in order that he can personally superintend the operation if he chooses. Should winding have been stopped for a long time, it is not necessary to test every six months; but before the rope can be used again it must be tested.

Jan 1, 1901

By Richard E. Gray, William S. McCann, Robert C. Speck, Robert W. Bruhyn

Subsidence of the ground surface is the inevitable result of high recovery longwall and room and pillar coal mining operations. Up to now, U.S. research into this phenomenon has been concerned primarily with documenting the magnitude and extent of ground movements and prediction of the attendant ground strains through traditional ap¬proaches that have been developed in Europe and the United Kingdom. Preoccupation with ground strain prediction has, unfortunately, diverted attention from the more meaningful objective of predicting the severity of damage to structures at ground surface and the prob¬able cost to repair such damage. An attempt has been made to rectify this situation by reviewing in detail one hundred thirty four cases of subsidence damage to dwellings above active mines in western Pennsylvania, identifying the types of damage and the circumstances under which damage took place. The data reveal that damage to dwellings virtually always includes basements in addition to the readily apparent effects to the superstructure. In 90 percent of the subsidence cases, more than half the repair cost is associated with damage to subgrade components. A damage classi¬fication system has been devised that relates observed damage to severity and repair cost in a uniform manner for conditions in the Northern Appalachian Coal Field. Damage severity has been examined in the context of depth to the mine, the character of the near¬ surface overburden materials, mining type and other parameters.

Jan 1, 1983