Search Documents

By R. T. Mishler

I wish to express my keen appreciation of the article on the above subject by Coe and C1evenger.l It has been doubly interesting to me, for the reason that the experience recorded and the principles evolved practically parallel the results of similar investigations made by myself and others at The Lucky Tiger Mine, El Tigre, Sonora, Mex. An outline of the work at El Tigre may aid in confirming the principles expressed by Coe and Clevenger. El Tigre has the unenviable distinction of possessing a slime with a much lower settling rate than any recorded in the article discussed. Under most favorable conditions the settling rate is about one-third that reported for the Liberty Bell mill, and one-tenth that reported for the Nipissing, Golden Cycle, and Presidio mills. This slow settling characteristic of Tigre ore has necessitated careful investigation of settling phenomena throughout the various evolutions of the plant. Previous Settling Investigation at Tigre During construction work at the mill, the metallurgical engineer in charge, D. L. H. Forbes, ran a series of experiments on settling. His tests proved that deep settling tanks were not ordinarily necessary. The use of tanks 2 or 3 ft. in depth was suggested.2 Later experiments demonstrated that the following principles of settling applied to Tigre pulp.3 1. In settling dilute pulp, settling rates are independent of pulp depth. 2. In settling thick pulp, settling rates are approximately proportional to pulp depth.4

Jan 1, 1918

By F. M. F. Cazin

Some twenty years ago the author of a book,* by which, for the first time, molecular action was made to account for nearly all phenomena in hydrodynamics, began his preface as follows: " It is contrary to all experience, that any branch of science should suddenly cut short its own line of reasoning, and drop all connection with its past, and yet as quickly re-establish itself on an entirely new basis. It is, therefore, not without justification that this book should be met with caution and even distrust." When the newly-discovered natural facts and laws presented in this paper were, in 1891, first laid before the officers of the American Institute of Mining Engineers, they might have been preceded by a preface to the same effect; and the expression would have found its justification by the actual experience these facts and laws met with. Since then, as the result of their publication in one of the most prominent

Jan 1, 1895

By Zay Jeffries

IN this paper, it is proposed to outline a method for the determination of melting points of those metals and alloys having high fusion temperatures. The application of the method as used to determine the melting points of alloys of tungsten and molybdenum will be given. It will be seen from these results that tungsten and molybdenum form a completely FIG. 1.-PARTIAL SECTION OF APPARATUS USED TO DETERMINE MELTING POINTS OF TUNGSTEN AND MOLYBDENUM ALLOYS. isomorphous series. This is also verified by the accompanying photomicrographs. Tungsten and molybdenum have been found to crystallize in the salve system, namely, isometric, and the crystal units are cubes. These determinations were made by examining etching pits in the pure metals.

Jan 7, 1916

By E. H. Bunce, E. C. Handwerk

The inherent difficulties of zinc smelting arise from the fact that metallic zinc is volatilized at the reducing temperature of zinc oxide and thus is liberated in the form of a vapor. This vapor must be subsequently condensed to obtain metallic zinc, first in molten and eventually in solid form. Zinc vapor is sensitive to oxidation not only by air but by combustion gases containing carbon dioxide. It is, therefore, necessary to carry out both the reduction and the condensation operations in a closed system consisting of an externally heated muffle with attached condenser from which extcrnal oxidizing agencies are excluded. However, the reoxidation of zinc vapor cannot be entirely prevented by excluding external sources of oxidation. Internal sources of oxidation are necessarily present when oxidic zinc ores are reduced by a carbonaceous reducing agent. The reduction reactions themselves involve, first, the production of carbon monoxide in an amount at least equal in volume to the zinc vapor produced in the reaction, and, second, the formation of carbon dioxide. Not all of the carbon dioxide is reduced again to carbon monoxide by the excess carbon in the time available, and the slightly oxidizing condition, which results, seriously affects the efficiency of the condensation of the zinc vapor to the metallic state. In the past the difficulties arising from these causes have limited practical zinc smelting on an industrial scale to the use of small retorts equipped with small condensers. The retorts had to be small, because a closed refractory container capable of excluding oxidizing gases from the heating chamber surrounding the retort could not be built in large dimensions. The size was also limited because ordinary refractories when thin enough to conduct heat readily are not capable of sustaining a heavy load of charge at high temperature. Moreover, a loose charge of zinc ore and carbonaceous reducing material such as fine anthracite coal or coke breeze is a poor conductor of heat, thus limiting the cross section of the retort. The operation of these small retorts requires arduous

Jan 1, 1937

By B. H. Cody

THE Morenci concentrator of the Phelps Dodge Corporation is a part of the project that was completed after five years had been spent in development of the open-pit mine, equipment and process testing in the former No. 6 concentrator, and construction of the reduction works. The reduction works, of which the concentrator is a part, is about a mile and a quarter southeast of Morenci, on the highway that leads up Morenci Canyon. The concentrator has a nominal capacity for the treatment of 45,000 tons of ore daily. The original plant, which has a rated capacity of 25,000 tons of ore daily and is now in its fifth year of operation, began production on Jan. 30, 1942. The addition, to increase the capacity 8o pct, began operation on Dec. 1, 1943. The equipment of the original plant has been described in MINING AND METALLURGY (May 1942). No changes in equipment were recommended for installation in the concentrator extension and only one major change, forced by a shortage of maintenance labor, has since been made. Metallurgical treatment has been altered in some ways as experiments progressed and as labor and economic conditions dictated. No complete description of the operation of the concentrator has been published, so this paper will record such operating and equipment changes as have been necessary, the operating methods that have been developed and the metallurgical results that have been obtained. Descriptions are given in the order of the processes with a flowsheet and an equipment list of each process for convenient reference. The questions asked by engineer visitors have guided the detail in which operation and maintenance are described. During the period Jan. 30, 1942 to Sept. 1, 1946, ore milled has totaled 43,595,253 dry tons, from which 1,643,885 tons of concentrate have been made, containing an indicated production of 783,164,809 lb of copper. The principal results obtained in operation of the concentrator during the years 1942 to 1945, inclusive, and to Sept. 1, 1946 are shown in Table 1. A graphic general flowsheet of the plant is given in Fig I. ORE The Morenci ore that is now being treated is a medium-hard monzonite porphyry in which the principal sulphide minerals are chalcocite and pyrite. A minor amount of covellite is present. Chalcopyrite and bornite have been observed under the microscope. The chalcocite occurs mainly as a coating on pyrite. Some of the coatings are so thick that the pyrite presents the appearance of being an inclusion in chalcocite. Some are less than one micron thick and are barely visible at 500 diameters magnification of a polished cross section. Some chalcocite is present as a dissemination in the gangue. Various oxidized copper minerals are present as a result of oxidation in place but they represent a minor proportion of the copper minerals of the ore body. Oxidation

Jan 1, 1947

By H. A. Coy, James A. Noble

The Mascot mines of the American Zinc Co. of Tennessee are situated at Mascot, Tenn., 14 miles northeast of Knoxville, on the Southern Railway. The district is centrally located in the Great Valley, or Appalachian Valley Province. Prior to 1900, a small output of zinc was obtained from oxidized ore mined in open pits. In 1900, a shaft was sunk to sulfide ore, and in 1903, a second shaft was put down, neither being as deep as 200 ft. The American Zinc Co. of Tennessee began drilling in 1911, and outlined an ore-body to which its No. 1 shaft was sunk, to a depth of 365 ft. Since that time, the American Zinc Co. of Tennessee has been the only operator in the district. The Federal mining laws have never been in operation in Tennessee and mining lands are as irregular in boundary and area as farm lands. Ownerships are generally held in fee. In most cases the surface and mineral rights are transferred together. Electric power is supplied at 66,000 volts by the Tennessee Power Co., from a hydro-electric plant at Parksville, Polk County, Tenn., 100 miles from Mascot. No other power is used, but an emergency steam plant is held ready in case of interruption of service. Labor is all native and non-union. Negroes are employed for most of the shoveling, and for a few miscellaneous jobs, but for almost no other work. Exploration Exploration is carried ahead of mining largely by surface drilling. Both churn and diamond drills are used. Holes are not spotted according to geometric plan, but to block out ore outlines with the least number of holes. Churn-drill cuttings from each 5-ft. run are mounted for formation record, and in ore ground, all the bailings from each 3 ft. of advance are sampled and assayed. Diamond-drill cores are sampled and a specimen core filed for formation record. In ore ground, all the core

Jan 1, 1925

By A. J. M. Ross, R. G. Wayland

The Homestake mine is situated in Whitewood mining district, in the northern Black Hills of South Dakota, in the city of Lead, Lawrence County. The entire property, comprising 557 lode claims with a total area of 3343 acres, is held under United States Patent. The older claims were 300 by 1500 ft. under local regulations, the newer ones 600 by 1500 ft. The Homestake was discovered April 9, 1876, by Moses and Fred Manuel, and Jake Harney, who were drawn into the northern hills, from the Custer placer district, by news of the discovery of rich placer deposits in Deadwood Gulch. They located a number of additional lode claims and, in a short time, the whole country was covered with locations. The Manuel brothers built an arrastre the following winter and took out $5000. The next year the Homestake lode was sold to Senator George Hearst and associates, who organized the Homestake Mining Co. Other companies were formed to exploit other groups of claims and at one time fivc companies were operating on this deposit, the Father DeSmet, the Dead-wood-Terra, the Caledonia, the Highland, and the Homestake Mining Co. These companies, however, have been merged into the Homestake Mining Company. The first stamp mill, known as the "Eighty Mill," commenced operation on July 12, 1878, and production has been nearly continuous since that time. Geology The orebodies of the Homestake are found in an intensely folded and altered bed of dolomitic limestone occurring in a series of ancient rocks believed to be of Archean age, belonging to the Keewatin series. The Keewatin series is estimated to be 20,000 ft. thick and is made up essentially of quartz mica schists, garnet schists, quartzites, slates, and some green schists, probably derived from basic igneous rocks. The dolomitic limestone bed has a thickness of 40 to 60 ft. The great width of ore, as much as 400 ft. in some of the stopes, is due to the folding, wherein the bed is repeated. In other cases the bed is stretched and pinched out. Dikes of Tertiary rhyolite cut across the country and, in places, sills overlie the

Jan 1, 1925

By C. W. Nicolson

THE Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large

Jan 1, 1938

By Carolyn Barnes

The Offshore Technology Conference, the world's largest technical conference and exhibition on the development of offshore resources and protection of the ocean environment, is sponsored annually in Houston, Texas, by 12 international engineering and scientific societies. This year's OTC, the seventh, will be held May 5-8 at the Astrodomain, and will be the largest in its history. The technical program for the first meeting in 1969 consisted of 100 papers, an exhibit display of 380 booths, and an attendance of 4300. This year. 280 technical papers are to be presented, and more than 2800 exhibit booths, representing some 1200 companies and nine countries, will be on display for an anticipated audience of 40,000.

Jan 4, 1975

By E. J. Schmitz

Coming from San Antonio, Texas, and following the Galveston, Harrisburg and San Antonio Railroad westwards, one enters soon the Cretaceous formation, which forms a belt of several hundred miles, extending westwards to the boundary of Arizona and across the Rio Grande into the State of Coahuila, Mexico. The members of this formation are very numerous and in petrographical character very diverse—from a whitish or bluish, slaty, impure limestone to a hard, beautiful blue-and-red striped, and a compact heavy-bedded,

Jan 1, 1885

By Peter M. Grant

The paper describes in broad outline the design of circular shaft linings with particular reference to the practical aspects. In the main it refers to recent British and German practice but has general application for any shaft lining design.

Jan 1, 1983

By J. W. Halley, T. S. Washburn

Rimming steels derive their name from their action during solidification in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop in the molds, are determined by the composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.? The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors6 Meyer: in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federation9 studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accurately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring conditions and furnace practice on the distribution, though there is still much to be done in this direction. The structure of a rimmed ingot that has been split by dynamiting and a schematic diagram of the zones in the ingot are illustrated in Fig. 1.

Jan 1, 1938

By A. J. Lyon

The stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening, which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging—heating in a temperature range below 170" C. (340" F.)—will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1929

By Simon D. Strauss

COPPER In terms of mining activity, copper is the leading nonferrous metal. It is true that in recent years the volume of aluminum consumption in the non-Communist world has exceeded the volume of copper consumption, but virtually the entire primary aluminum supply is derived from bauxite. On the average, only four tons of bauxite need be mined to produce a ton of aluminum. By contrast, the highest-grade, large-scale copper mines now in operation (those in the Congo) must mine at least 20 tons of ore to produce a ton of copper. In the United States an average of 150 tons of ore must be mined to produce a ton of copper. This does not take into account the huge amounts of waste overburden that must be stripped from the open-pit mines to account for their steadily rising share of the world's copper output. Copper epitomizes the economic problems of the mining industry in many ways. Its price is highly volatile, considering its great economic importance. It has been a tool of mankind longer than any other of the base metals-the dawn of history has been classified as "The Bronze Age." World Copper Production Although copper is mined in many countries, in recent years 70% of the non-Communist world production has come from six countries. Two of these are industrialized countries and are large consumers-United States and Canada. The other four are developing countries with very small domestic requirements-Chile, Zambia, Zaire, and Peru. Heavily dependent on copper exports to sustain their domestic economies, these countries find themselves oscillating between prosperity and depression with the changing levels of copper prices. In an effort to control their own destiny, in 1968 they formed an organization of copper exporting countries (CIPEC) which was designed to study copper markets and possibly to intervene actively in these markets. (When this chapter was being prepared, no actual steps along such lines had been taken.) Many of the leading industrialized nations are wholly dependent on imports for their primary copper supplies. These include West Germany, the United Kingdom, France, Italy, and many others. Japan, now the non-Communist world's second largest copper consumer, produces only 10 to 15% of its requirements from domestic mines. Although the bulk of the copper output is smelted in the country where it is mined, there is a limited international trade in copper concentrates. Canada, the Philippines, Australia, and Papua-New Guinea are significant exporters of copper concentrates; Japan, Germany, the United States, and Sweden are importers. However, this trade accounted for only about 10% of the non-Communist world production of copper during the decade of the 1960s.

Jan 1, 1976

By Ian W. Wark, Keith L. Sutherland

IT has been shown' that in the absence of heavy metal salts, the nature of the alkali used to promote differential flotation-whether caustic soda, lime or sodium carbonate-is unimportant. The hydroxyl ion is the active depressant upon which differentiation depends, and the pH value determines whether a film of collector forms on any given mineral surface. Even when sodium cyanide is used in conjunction with alkalies, it is the pH value and not the nature of the alkali or its concentration that is important, for upon the pH value alone depends the fraction of the added sodium cyanide that is present as cyanide ion, which is the true depressant. When heavy metal salts become dissolved from partly oxidized ores, or are added intentionally as activators, conditions are different, and metallurgists have found that lime and sodium carbonate do not give identical results, even when added in amounts sufficient to produce the same pH value. In the few instances in which we had attempted to confirm this view, we had failed to do so, for, with nothing to guide us, we had inadvertently chosen solutions that gave contact curves of a "standard type," which correspond to conditions of ready floatability. Now, however, we find that, in the presence of copper salts, and within a restricted range of reagent concentrations, the nature of the anions present is important, and that sodium carbonate does influence the results, apart from the usual effect due to its influence on pH value. With the recognition of this anion effect, and with the control of temperature already introduced,2 it appears that the factors of major importance in connection with this set of reagents have been taken into consideration, and that the results obtained and the conclusions drawn from contact tests will be of more immediate value to the operator. It is not difficult to suggest an explanation for the influence of the carbonate ion in the presence of copper sulphate. The works of Picker-

Jan 1, 1939

By P. G. Beckett

The problem of handling the large quantities of water encountered in the Old Dominion mine presents many features of interest. In the present paper are discussed the probable sources of water, the pumping equipment, the increased flow into the mine in the early part of 1915, culminating in the flooding of the 18th and 16th levels in March of that year, and the difficulties that were met with during the high-water period. I. PRELIMINARY The Old Dominion mine, situated 1 mile north of the town of Globe, Ariz., has long been one of the prominent copper producers of the State, and until the opening up of the copper schist deposits in the neighboring mines of Miami, was responsible for the greater part of the copper output from the Globe district. As the gradual exhaustion of its orebodies near the surface led to the downward development of the mine, more water was encountered in the western portions directly underlying the dacite formation until the drainage problem became a serious factor in the operation of the mine and in the economical extraction of the ore. A heavy inrush of water on the 10th level of the mine in 1906, preceded by still earlier water difficulties, rendered imperative the immediate installation of a pumping equipment capable of handling large flows of water. While the Old Dominion has been recognized as a wet mine since its early days and one in which the complete control of the water situation was of paramount importance in the development of the lower levels, it is chiefly in the last nine years, since the installation of the increased pumping equipment, that the mine has developed and handled large quantities of water. Its maximum pumping record was reached in the first six months of 1915, during which time, following a prolonged period of abnormal precipitation, the pumps handled 1,624,740,000 gal. of water; while in the month of March alone, over 407,000,000 gal. of water were pumped from the mine.

Jan 1, 1917

By J. W. Halley, T. S. Washburn

Rimming steels derive their name from their action during solidification in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop in the molds, are determined by the composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.? The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors6 Meyer: in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federation9 studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accurately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring conditions and furnace practice on the distribution, though there is still much to be done in this direction. The structure of a rimmed ingot that has been split by dynamiting and a schematic diagram of the zones in the ingot are illustrated in Fig. 1.

Jan 1, 1938

By W. C. Coffin

Fire-brick stoves have become a necessary part of the modern coke blast-furnace equipment, and are also superseding the cast-iron pipe stoves in anthracite- and charcoal-furnaces. The brick stoves in general use are of either the Cowper or Whitwell type, or modifications of these bearing the names of those who invented the alterations from the original types rather than any real departure from then]. All these stoves have approximately the same valve-equipment and follow the same line of operation. The waste gas from the furnace enters at one port and burns in a single combustion-chamber, and the heated products are drawn through the various passe; in the brickwork to a stack of proper height to create the necessary draught. The last passes of these stoves receive a very small percentage of the heat from the gas, owing to their extreme distance from the combustion-chamber; and this chamber also suffers great deterioration in the attempt to force the heat into the farthest passes. At best, about 70 per cent. of the heat taken up is held in the combustion-chamher and the first down-pass of the Whitwell stoves. Mr. Hugh Kennedy, Manager of the Isabella Furnaces, Pittsburgh, Pa., who has had a large experience with the fire-brick hotblast stoves, was so strongly impressed with the fact that but about thirty per cent of the brick of the average stove were doing proper duty as heat-agents, that, after careful study and experiment, he had three 20- by 60-feet stoves constructed with a view of more uniformly heating all the brick. In these the general lines of the Whitwell stove are followed, with the blast-connections unaltered, but gas is introduced at the bottom of each pass, and outlets are provided at the top, so that the gases have a direct natural draught in each pass and the highest heats are obtained at the bottom instead of the top. The natural tendency being toward the reverse condition, the brickwork soon acquires an almost uniform temperature.

Jan 1, 1893

By John E. Conley

THE slate industry of the United States has shown a marked decline in value of products made annually since the peak year 1925, although there has been moderate improvement over the lean years 1932 to 1934. In 1940, the value of all slate products sold was approximately 5 ¾ million dollars for a total output of 473,450 short tons. The quantity sold was a little less and the value a great deal lower than the annual averages for the past two decades. Enormous quantities of waste materials result from the quarrying, splitting and milling of slate. Obviously, utilization of such waste material is desirable, not only from the viewpoint of economical operation but also for the purpose of conserving natural resources. One possible use is to produce expanded or puffed lightweight aggregate for use in concretes. Such concretes are strong enough for specific uses, and the advantage of lightness could be obtained in such structures as the walls and roofs of buildings, suspension-bridge roadways and various other applications where weight is a factor. Conceivably, these uses could consume an appreciable annual tonnage. USE OF WASTE SLATES FOR MAKING AGGREGATES The lightweight-aggregate industry has been discussed elsewhere4.5 and need not be covered in detail in this paper. The materials commonly utilized are naturally occurring aggregates such as volcanic cinder, tuff and pumice; by-product materials, such as ordinary cinders and air-cooled slags; and the specially manufactured products, including Haydite, Pottsco, Gravelite, Cel-seal, Superock and Waylite. Slates, however, have not been given the consideration they merit, especially in the United States. In the British Isles, some work has been done3 on certain Welsh slates by the Building Research Station to stimulate the use of these wastes. REQUIREMENTS FOR RAW MATERIALS As pointed out by Hughes,4 the light-weight-aggregate industry is segregated in regions adjacent to large cities in order to localize the market and avoid the necessity of long freight haulage. Waste slate from the deposits of eastern Pennsylvania, northern Maryland, and Virginia would meet the basic requirement of any low-priced structural raw material. One apparent advantage is attained when slate waste, normally discarded, is utilized in the manufacture of a by-product. Mining or quarrying costs usually have been assessed against the main product. Some additional grinding might be desirable, but this operation would be relatively cheap, as most slates grind easily. It is believed that virtually all slates, when properly heated, will expand to some degree. However, types that will expand from 3 to 7 times their original volume are preferred. Fig. I illustrates the expansion of a Pennsylvania slate. The cube originally

Jan 1, 1942

By D. G. F. Hedley, S. N. Muppalaneni, J. W. Roxburgh

A stope and pillar method is used to mine the gently-dipping uranium bearing reefs, to a depth of 1000 m, at Elliot Lake, Ontario. A few isolated rockbursts have been reported in the 11 mines in the area during the first twenty-five years of operation. However, in March 1982 a series of rockbursts were initiated in the old mined-out workings at the Quirke Mine of Rio Algom Ltd. Detailed records of pillar deterioration and size of the affected area were kept both prior and subsequent to the occurrence. Seismic instrumentation was installed before and convergence stations shortly after the start of bursting. Observations indicate that the squat pillars failed violently where- as the slender pillars exhibit a less violent failure mechanism. Floor cracks and heaving are common, but the massive quartzite hanging wall strata is relatively undamaged although some roof falls have occurred due to local structure. The microseismic system accurately locates seismic events to f 20 m within the geophone array and it has been found that an accelerating convergence rate coincides with and in some cases precedes an increase in seismic activity. Displacement discontinuity and boundary element computer models have been used to estimate pillar stresses and areas of high stress concentration in an effort to determine the causes of rockbursts. Mine and pillar stiffness and energy balance concepts are used to explain cases of gradual and sudden pillar failures at Quirke Mine.

Jan 1, 1984