Search Documents

By R. P. Heuer, Paul M. Tyler

THE literature on refractories, although fairly extensive, is so scattered through books and periodicals as to be difficult of access to the general reader and most of the individual papers serve merely to illuminate some particular phase of the industry. Two general treatises by American authors8.16 are available, also the somewhat older works by a well-known British authority, 12,13 but these make their appeal to the technically minded ceramic engineer. Another small group of publications deals with the use of refractories, mainly in the iron and steel industry.1, 3,5,6,11,15 Raw materials utilized by the refractories industry have been covered by sundry books and articles. For the relatively nontechnical reader and economist, however, there appears to be no single review that purports to describe the industry as a whole. Furnace linings and other products that are classed as "refractories" are designed primarily to withstand high temperatures but this important property is by no means the only requirement; a suitable refractory material must likewise withstand slagging (chemical' action), abrasion (physical wear), and spalling, as well as the various other stresses and physical phenomena induced by heat, of which softening or incipient melting is only one phase. Nevertheless, subject to these highly practical considerations, the definition of a refractory material is based upon temperature resistance. Broadly speaking, any material that shows obvious signs of fusion after being heated slowly to 1500°C (2732°F) cannot be classified as a refractory material. The characteristic properties and requirements of refractory materials are conveniently summarized in Fig 1, prepared on the American Refractories Institute Fellowship at Mellon Institute, Pittsburgh, Pennsylvania. Most of the factors of service and properties of refractories given in this chart are interdependent and are greatly affected in degree by the functions of temperature and time. The factors in the chart are believed to cover the commoner questions.

Jan 1, 1949

By Anthony Anable, J. V. N. Dorr

When separate treatment of sand and slime by cyanidation was the rule rather than the exception, as now, and when gravity concentration, rather than flotation, was the accepted method of dressing copper, lead, zinc and other base ores, classification was a separate step in ore treatment. Today, however, the picture is much different. The trend toward all-slime treatment in cyanidation and flotation has made fine closed-circuit grinding essential, and the mechanical classifier is of equal importance with the mill in the preparation of an ore for its treatment. Actually, a mill and classifier are a unit, a variation in either affecting the desired results. In developing this thesis—the mutual interdependence of the rotary mill and the classifier in modern fine-grinding practice—it would be well to consider first the different types of classifiers and mills in use today, their scope and limitations and the factors governing their selection. From such a basis as this a logical approach may be made to modern closed-circuit fine grinding, the evolution of multiple-stage grinding practice, the relation of the classifier to the mill and, finally, the trend to higher and higher circulating sand loads in the mill-classifier circuit. Such data as are germane to the subject will be given to support the thesis advanced. Mechanical Classifiers Theory.—Stokes' law, applicable to the uniform slow motion of a rigid sphere in a viscous fluid of infinite extent, states that the velocity of a particle settling under the influence of gravity is a function of the square of its radius: _ 2 g(ds - de)?2 v =9 S Where V = velocity of particle in cm. per see. g8, acceleration due to gravity d8, density of particle de, density of fluid ? = radius of particle S = viscosity of fluid

Jan 1, 1935

By J. C. Humbert, J. F. Elliott

The solubility of nitrogen in liquid pure Fe, Cr, and Ni, in liquid Fe-Ni, Fe-Cr, and Ni-Cr alloys and Fe-Cr-Ni alloys, has been measured by the Sieverts' type apparatus between 1500° and 1800°C. Tabulations and graphs of the solubility data and activity coefficients are shown. Heats of solution are reported. Interaction coefficients of the several elements in Fe. Cr, and Ni ave also reported. THE solubility of a gas in a liquid metal is usually measured by either the quenching technique or the so-called Sieverts' method. In the quenching method, 1-3 the melt is equilibrated at the desired temperature and pressure with the gas phase having a known fugacity of the gas being studied. The melt is sampled and the sample is quenched and analyzed chemically for its gas content. In Sieverts' method the melt is contained in a closed chamber. The apparent volume of this chamber, i.e. the "hot volume," is usually determined by introducing a known quantity of an inert gas having very closely the same physical characteristics as does the experimental gas. Alternatively, the experimental gas is used with an inert specimen having the same general physical characteristics as does the experimental melt. Subsequently, the experimental melt is equilibrated with the experimental gas by introducing a known quantity of the gas into the calibrated chamber. The solubility of the gas is obtained from P-V-T relationships. The quenching method suffers from' the limitation that some gas may be gained (as in the case of Cr-Fe alloys) or lost (as in the case of Fe-Ni alloys) during solidification and cooling of the sample. With Sieverts' method sampling and analysis are unnecessary. However, errors can result from the difficulty of determining accurately the "hot volume,"

Jan 1, 1961

By Theodore Simons

Permission to present this paper at the February, 1915, meeting of the Montana Section of the American Institute of Mining Engineers was liberally granted by W. A. Clark, Jr., President-and General Manager of the Timber Butte Milling Co., and by the representative of the Minerals Separation Co. For the many courtesies shown the writer on his visits to the mill and for information supplied, he is indebted to all the officers of these companies, especially to W. N. Rossberg, W. D. Mangam, Hamilton Cooke, Jr., T. M. Owen, T. C. Wilson, R. McGillivary, L. L. Quigley, C. Bartzen and others. The writer takes this opportunity to herewith express to them his appreciation and sincere thanks. Location of Mine and Mill The concentrator of the Timber Butte Milling Co. was built to treat the ore mined at the Elm Orlu mine of the Elm Orlu Mining Co., which carries zinc and lead in sphalerite and galena; copper in bornite, chal-cocite, tennantite, and tetrahedrite; and gold and silver either free or chemically combined with the sulphides of the base metals. The gangue is chiefly quartz, barite, fluorite, rhodonite, and rhodocrosite. The iron in the ore occurs as irqn pyrites. The Elm Orlu mine is situated in Butte, Silver Bow County, Mont., near the northern border of what is locally known as the Butte sulphide-copper belt, about one mile north of the Anaconda mine, and adjoining the Black Rock zinc mine of the Butte & Superior Co. on the southwest. The mill is on the northern slope of Timber Butte, a prominent topographical landmark in the Butte district. This site permits to a large extent the gravity system of ore flow; it presents a convenient and extensive area for a tailings pond; and it is comparatively near to the source of water supply and to existing railroads.

Jan 1, 1916

By Harold W. Scott

Geological Engineering is now a recognized curriculum in most of the mining schools in United States. Graduates of these schools are scattered over the face of the earth, participating in exploration and mining enterprises of diverse character. They are engaged in the mapping of new mineral deposits, in the extension of old deposits, the estimation of reserves, microscopic analysis, and in the direction of exploitation and conservation of man's natural resources. The training of men qualified to carry out these technical phases of modern industry has fallen essentially to the mining schools. For the most part they have met the demand for technically trained men in the mineral industries. Schools Offering Geological Engineering Degree The mining schools have passed through the early stages of their development and at the present offer varied curricula covering the fields of geological engineering, mining engineering, and metallurgical engineering. Usually a B.S. degree is offered in any of these three fields. However, .there has been some tendency of recent date on the part of the Engineers Council for Professional Development to question the validity of a B.S. degree in Geological Engineering. The of this paper is to examine the curricula as offered in the mining schools, to evaluate their engineering content, and to propose minimum requirements for the degree of Geological Engineering in the mining industry. The curricula of eight institutions that offer the degree of B.S. in Geological Engineering or Mining Geology have been studied (Table 1). All except one of these schools are in or near mining districts and occur west of the Mississippi River. They are all state-supported institutions that have come into existence because of the state's need for technically trained men. A graduate from .a mining school is called upon to perform many duties of a technical nature. His initial task may be to make a geological map of a mine or the surface above, but before the map is finished he may be asked to take over the responsibility of getting the ore "on top." And finally, he might find it essential to know how to mill the ore. Certainly this requires technically trained men and the mining schools are essentially the organizations to do the job. The departments of geology in these schools are training geological engineers. Field Of Geology If we were to accept the opinions of some writers, we would be forced to conclude that all geology departments offer only a "dilettante" variety of subjects.

Jan 1, 1944

By Franklin Moeller

CONSIDERING the really short time that has elapsed since hydro-metallurgical processes of extracting copper from ores have been extensively developed, and the large scale on which this method is practised at Ajo, the successful operation of the plant must excite the admiration of every visitor. The application of the mechanical unloader to the purpose for which it is employed at Ajo is but an extension of the use for which it was originally designed, some 20 years ago, for unloading iron-ore vessels at the lower lake ports. At a time when the maximum output of a single machine, with men shoveling the ore into buckets, did not exceed 40 tons per hour, G. H. Hulett invented and constructed a mechanical unloader with a bucket of 10-ton capacity. This machine was of the steam hydraulic type, and it is still in operation after nearly 20 years of service. Several more machines of the same type were built, but the difficulties of power transmission, and the rapid development of electrical machinery, soon led to the adoption of electrically operated machines, and practically all of the later installations have been thus equipped. This electrically operated unloader has proved so well fitted for the work that the design of the lake boats has been practically revolutionized, with special view to the ease and rapidity of unloading. It is now possible to unload a 12,000-ton vessel with four machines in a little over 2 hr. This has necessitated an increase in the capacity of the machine, and the largest yet built handles an average load of 17 tons, with a possible maximum of 20 to 21 tons.

Jan 8, 1918

During the war period of quicksilver activity there were a number of departures from what may be termed the classical quicksilver metallurgy. Attempts were made to beneficiate low-grade ores by gravity concentration and flotation; mechanical furnaces began to replace the Scott furnace and the vertical coarse-ore furnaces, and condensers of sewer tile and redwood tanks were used in place of the older brick and stone condensing chambers. Other developments that have occurred during the current period of quicksilver activity are mainly in the nature of improvement and further refinement of those started during the war period. Each period of quicksilver activity has been accompanied by the proposal of various new processes, including wet methods for the treatment of quicksilver ores and innovations in furnaces, retorts and condenser equipment. As far as the author knows, nothing of economic significance in the way of "new processes" has been developed. There is in fact no real need for any essentially new process for the treatment of quicksilver ores; the direct furnace treatment is simple and inexpensive. Moreover, with rare exceptions, the quicksilver industry has no complex or refractory ore problems corresponding to those which are receiving more and more attention from metallurgists in other branches of the nonferrous field. Untler these conditions improvements in quicksilver metallurgy must be looked for through the adaptation of current developments in engineering and metallurgy generally to the particular needs of quicksilver practice rather than through the invention of new processes. Preliminary Treatment of Quicksilver Ores At Sulphur Bank, in the treatment of old dump material left by the early operators, wet screening is being used as a preliminary step in concentration ahead of flotation. Power shovels and trucks are used to deliver some 400 tons of ore per day to the lower terminal of a hoist, which in turn discharges the material at the top of the screening plant. Wet screening is carried on in two stages. Depending on the character of the material, 1-in. or 2-in. punched screens are used on the first trommel.

Jan 1, 1930

By J. V. N. Dorr

THE Elko Prince mine is in the Gold Circle district, Nevada, about ½ miles(2. 4km.) from the town of Midas, 55 miles (88.5 km.) west of Battle Mountain and 50 miles (8.5 km.) northeast of Golconda. The district is described by Emmons in U. S. Geological Survey Bulletin 408, 1910. Little was said of the Elko Prince, however, as only a small amount of work had then been completed. The geological structure of the region is simple. The oldest exposed formation, covering most of the area, is rhyolite, which has a light-colored devitrified groundmass enclosing phenocrysts of feldspar, quartz, and magnetite. It has been somewhat weathered and partially stained with oxide of iron. There are several outcrops of andesite which cut the rhyolite. The ore deposits occur as fissure veins, replacement veins, and sheeted zones. The Elko Prince vein is of the first type. The rhyolite near the veins is silicified, stained with oxide of iron, and, at some localities, replaced by ore, or is so permeated by metals as to be classed as ore. The vein filling consists chiefly of quartz, and the values consist entirely of gold and silver. Part of the gold exists as the native metal and part is associated with pyrite. Silver occurs free and its argentite in handed streaks through the vein. These veins trend in a northwesterly direction, with dips varying from 65° to vertical.

Jan 8, 1918

By R. J. Colony

The failure, or disintegration, of concrete in structures, even when the cement, sand, and coarse aggregate used have passed satisfactorily all tests and inspections, is not uncommon. Such failures occur even when proper methods of mixing and placing have been used and where weather conditions were correct. In these cases, the origin of the trouble must be sought in the cement; therefore some additional mode of determining the quality of cement must be employed. The problem is to find a simple, usable, easily applied method that will supplement the standard tests. The solution of this problem involves a knowledge of the chemical composition of Portland cements, also of their constitution (or componental composition), as the behavior of a cement, when gaged, is dependent on the physical and chemical characters of the compounds of which it is composed, the proportions existing between them, and the fineness of grinding. It is likewise essential to know the character, behavior, and composition of the hydration products of Portland cement. The most promising method of attack makes use of chemical, mechanical, and petrographic methods. Chemical, by determining quantitatively not only the usual constituents, but the carbon dioxide and water. Mechanical, by determining the fineness with the air analyzer,' which separates into fractions of various grain dimensions all of that portion which in the ordinary sieve test passes the 200-mesh sieve and constitutes at least 75 per cent. of the total cement. These fractions may be further studied chemically and petrographically and micrometric measurements can be made of the grains. Petrographic, by the method of immersion, and by making thin sections from test pats of both neat cements and standard mortars. Normal Portland cement is composed of mechanical mixtures of definite chemical compounds having constant chemical and physical properties. In the order of their cementing qualities these are: Tri-

Jan 1, 1922

By George Frederick Kunz

The manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World's Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg.; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a ki1ogram. He also called attention to the fact that while this would depreciate the present diamoiid carat or pearl grain only about 2.5 per cent., it would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.' The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sévres, is largely due the eventual success of this eminently desirable reform, which he has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.3 The general adoption of a uniform standard for dealings in pre-

Jan 1, 1914

By L. A. Wright, H. L. McKinley

PINE Creek mine of Union Carbide Nuclear Co. is some 23 miles northwest of Bishop, Calif., in the Sierra Nevada Mts. Office and mill are 7800 ft above sea level, the 1500 level portal is at 9300 ft, the A level portal at 10,800 ft, and the 3050 portal at 11,500 ft. Original claims were located in 1916, and the mine worked intermittently until 1936, when it was purchased by Union Carbide Corp. Since then the property has been operated continuously, except for two brief periods when operations were suspended because of manpower shortages. Mine production through 1956 amounted to 2,792,425 dry tons of ore.

Jan 10, 1957

By Nicholas J. Grant, John Chipman

A FULL understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization; the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag-i.e., equilibrium conditions-and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck :20 [ ] Among others there appear the following:

Jan 1, 1946

By O. C. Wheeler

The reports for the years 1942 and 1943 were written in 1943 and 1944, respectively, and were summarized at the meetings of the Institute in February of those two years, but the manuscripts were held until released for publication in 1945. 1942 Lack of transportation facilities during 1942 resulted in a sharp curtailment of producing operations in Colombia at the middle of the year, and production of crude for export was thus greatly affected. Total production in 1942 amounted to only 10,617,008 bbl. Of this amount the Tropical Oil Co. produced 9,453,995 bbl., which includes 126,607 bbl. of petroleum condensate, and the Colombian Petroleum Co. produced 1,163,013 bbl, from its Barco property. The following summary, showing a comparison of the number of barrels of crude produced during the years 1941 . and 1942, reflects the extent to which producing operations were reduced during 1942: These above figures do not include any production recovered from Condor's (Shell's) Casabe wells during testing operations. An active exploratory drilling Program was carried out by several of the major companies, and the year 1942 established a record for wildcatting activity in Colombia. Excluding development operations on the Shell's Casabe wells on the Yondo concession, 13 wildcats were completed. Eight of these were in the Magdalena Valley, and all were abandoned; five were on the Barco Concession, and of these four were completed as producers. Particularly notable among the petroleum developments during 1942 was the continued success of drilling operations on the Shell's Yondo Concession of Compania Colombiana de Petroleos El Condor opposite Barranca-Bermeja. In 1941 the discovery well, Casabe No. I, was drilled and completed with an estimated initial production of approximately 480 bbl. of 19 1/2 A.P.I. gr. oil per day. In 1942, seven stepouts from the discovery well were successfully completed with initial production ratings ranging from 150 to 1230 bbl. per day. An extensive wildcat program on the Barco Concession of the Colombian Petroleum Co. yielded favorable results with the completion of four producers in the Socuavo and Tres Bocas areas; a fifth test, Sardinata Norte No. I, was abandoned at 500;" feet. Wildcatting operations in the lower Magdalena Valley area were initiated in 1942 With the drilling of a deep test, El Dote No. I, by Compania de petroleo Shell de Colombia. The well was a failure and was abandoned at a depth of 10,046 (?) feet. Wildcats on which drilling operations were being conducted at the end of the

Jan 1, 1945

By George H. K. Schenck

The investment analysis methods that are most generally accepted in the mineral industries in the mid-80's are presented along with their advantages and disadvantages. Also covered are current widely-used practices for introducing the uncertain nature of most of the important variables in an investment analysis, which is contrasted to the former dominance of deterministic analysis. Finally, the discussion turns to current practice for handling the two critical areas: cost of capital and inflation. The advice contained is reinforced with data from a survey of current practices in the petroleum industry.

Jan 1, 1985

By Rollin Farmin

"SWELLING GROUND" delivers pressure on mine timbers that originates in expansion of the wall rock, whereas "heavy ground" delivers only gravitative pressure. Of the several possible causes considered, the swelling is attributed to the physical surface action of water on gouge and flaky rocks at the periphery of the mine opening.

Jan 1, 1944

By F. Lynwood Garrison

There is probably no subject for study in the metallurgy of iron and steel of greater interest than the effect of manganese upon the properties of iron. Some of the peculiarities of iron and steel containing appreciable quantities of manganese were observed many years ago by Heath, Robert Mushet, and others; but it was not until the introduction of the Bessemer process, when a demand was created for large quantities of iron-manganese alloys, that such compounds of iron and manganese became articles of commerce. Since that time the demand for these alloys has steadily increased, the use of ferro-manganese not only becoming an absolute necessity in the ordinary Bessemer practice, but also essential to the manufacture of open-hearth, crucible steel and steel castings; in fact it is the only source of supply for all the manganese used in metallurgical opera-

Jan 1, 1893

By F. J. Arriagada

A conventional technique used to process auriferous sulfidic concentrates involves a pre-leach oxidative-roast step. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. Surface analytical techniques such as scanning electron microscopy and BET gas adsorption have been utilized to determine quantitatively the structural morphology of calcined pyrite and arsenopyrite samples in the range of 450 to 750 °C under an oxidizing atmosphere. In the case of. pyrite calcines a highly porous hematite product was found below 500 °C; at higher temperatures, a coarser oxide network , was observed. The surface area of these calcines was found to decrease sharply with increase in temperature. In contrast, the surface area of arsenopyrite calcines was found to follow a bimodal-type behavior with roasting temperature with maxima at 500 and 625 °C. In the case of pyritelarsenopyrite mixtures, the surface area was observed to increase dramatically as the content of pyrite increased. The appearance of pyrrhotite as an intermediate phase in the oxidation reactions is postulated to have important structural implications.

Jan 1, 1984

Jan 1, 1898

By William E. Ford, Edward Salisbury Dana

1. Normal Class (6) Zircon Type 2. Hemimorphic Class (7) Iodusuccinimide Type 3. Pyramidal Class (8) Scheelite Type 4. Pyramidal- Hemimorphic Class (9) Wulfenite Type 5. Sphenoidal Class (10) Chalcopyrite Type 6. Trapezohedral Class (11) Nickel Sulphate Type 7. Tetartohedral Class (12) Mathematical Relations to the Tetragonal System THE TETRAGONAL SYSTEM includes all the forms which are referred to three axes at right angles to each other of which the two horizontal axes are equal to each other in length and interchangeable and the third, the vertical axis, is either shorter or longer. The horizontal axes are designated by the letter a; the vertical axis by c (see Fig. 166). The length of the vertical axis expresses properly the axial ratio of a : c, a being uniformly taken as equal to unity. The axes are orientated and their opposite ends designated by plus and minus signs exactly as in the case of the Isometric System. Seven classes are embraced in this system. Of these the normal class is common and important among minerals; two others have several representatives, and another a single one only. It may be noted that in four of the classes the vertical axis is an axis of tetragonal symmetry; in the remaining three it is an axis of binary symmetry only.

Jan 1, 1922

By B. H. G. Brady, C. M. St. John

Computational schemes for analysis of rock mass response to excavation, loading and other imposed changes, are employed pervasively in rock mechanics practice. Applications range in complexity from determination of stress and displacement distributions around openings, to prediction of the thermo-hydromechanical behaviour of a saturated fissured mass. While this may be taken as apparent sophistication in rock mechanics design activity, the indiscriminate use of computer methods may sometimes conceal inferior and inadequate engineering procedures. These inadequacies may not always be recognized, due to the general uncertainties which are inherent in rock mechanics investigations. This paper seeks to identify some common deficiencies in rock mechanics applications of computational schemes, and to propose ways of eliminating them. It also indicates some specific developments and applications of computational procedures, which are required to address persistent design problems in geomechanics practice.

Jan 1, 1982