Search Documents

By William M. Camp

An extensive design phase testing program in which 10 piles and 2 drilled shafts were instrumented and statically load tested to failure, was undertaken to establish relevant foundation design parameters for two bridges in Charleston, South Carolina, USA. The bearing strata at both test sites was a calcareous, overconsolidated, firm to very stiff, slightly sandy, clayey silt (locally known as Cooper Marl). Confirmation dynamic and static loading tests on production piles indicated only 50 to 60% of anticipated pile capacities; including consideration of time effects. Supplemental subsurface explorations did not reveal any significant variations in marl properties. Ultimately, 22 static and 75 dynamic tests were performed on production piles for a 2 mile section of the project. Pore water pressures in the marl were also monitored during and after pile driving. A study of unit skin friction in the marl as a function of time revealed two distinct trends: piles driven in areas with a sand overlaying the marl gained more capacity significantly faster than those driven through a clay or silt. Although the insitu marl properties are apparently similar across the site, the material immediately above the marl evidently has a large effect on pile capacity. This effect of overburden on pile capacity was verified by testing piles over a period of two years.

Jan 1, 1993

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1973 is compared with consumption in 1972 and 1974 (preliminary data).

Jan 1, 1976

By Jim Gunderson

Jan 1, 2004

By P. Mousset-Jones, G. Danko

Variations of the temperature and steam/moisture content of the air with distance and time are modelled for a single airway. The input for the simulation is an air temperature that varies with time, together with the moisture/steam content that results, for example, from a fire with a given distribution of heat and of fume concentrations at the beginning of the airway. The transport of heat and moisture to the surface of the wallrock is assumed to be simultaneous. Such multiphase convection may result in evaporation from the moist wall close to the fire and recondensation downstream. The modelling of this non-linear effect is a unique feature of the new simulation. A new analytical solution is used to calculate the conduction of transient heat within the rock mantle, which, in the event of a fire, is typically a short-term process. This allows for an arbitrary variation of surface temperature with time - unlike that permitted by the age function solution, which is limited to stepped temperature changes. An iterative numerical scheme that has recently been developed to simulate mine climate is used to calculate the coupled transient heat conduction and multiphase surface heat transport in successive length increments along the airway. To demonstrate the simulation procedure a numerical example is presented in which a fire with a given distribution of heat and fume concentrations with time is located at the beginning of an airway

May 1, 1991

By P. S. Capper

"Generally speaking, the most intensive efforts at dust control in the mining industry have, in the past, been concerned with underground operations and where uranium ore or high silica material is processed. In the past several years, Stoop Rock has made Intensive efforts to reduce dust levels in it's Iron ore pelletizing complex. There have been no great engineering break-throughs with regard to dust control in such plants, and certainly no new engineering techniques have had to be applied at Steep Rock. This paper deals with how significant improvements in dust levels have been achieved through minor modification to dust collectors and ventilation units, improvements in operating practices, and education of supervisors and hourly personnel.PROCESS DESCRIPTIONSteep Rock Iron Mines is located 120 miles west of Thunder Bay near Atikokan. (fig. 1) Run-of-mine ore is pelletized along with some -1"" concentrate that has been processed in the concentrator (a summer operation only), which utilizes gravity separation to upgrade a mechanical mixture of ore and waste."

Jan 1, 1976

By S. Pinard, J. MacLellan, G. Ehlert

"The Kidd Creek concentrator is looking actively for alternative technology as means of reducing operating costs in their concentrate handling section. The use of pressure and vacuum filters to eliminate the multiple hearth dryers would have the most beneficial effect. The dryers which constitute the greater portion of concentrate drying costs consume about 35,000 m3 per day of natural gas.After the evaluation of various filters by Kidd's technology group, it was clear that, because of the low final moisture requirements of 5.5 to 6% H20, few filters were able to achieve this target economically. Lately attention has focused on the Andritz hyperbaric filter. Testwork has shown that target moistures can be achieved with an appreciable reduction in operating cost.1.0 INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of Timmins, Ontario. The ore is hauled by the Kidd Creek Railroad to the concentrator where it is milled to produce separate copper and zinc concentrates.Projected concentrator feed for 1991 is 3,750,000 tonnes of ore grading 3.3 % Cu and 4.7 % Zn. The concentrate production is expected to be 458,080 dry tonnes of copper concentrate at a grade of 25.7 % Cu and 265,020 dry tonnes of zinc concentrate at a grade of 54 % Zn.Currently, there is active investigation toward cost reduction through implementation of new technologies. One area which has been extensively evaluated is the concentrate dewatering and drying section. In that section, the multiple hearth concentrate dryers represent the largest source of operating costs, mainly through maintenance and energy costs (electricity and natural gas). The replacement of these dryers with filtration technology that could produce the required concentrate dryness would represent substantial savings.In September of 1990 filtration testwork carried out by Andritz Ruthner showed that Kidd Creek copper and zinc concentrates could be filtered to below 6 and 8 % moisture respectively. In late May 1991 the laboratory testwork was duplicated on siteand one month later a 5 m2 pilot filter was tested on site. Based on the pilot test results, an economic evaluation was performed. It indicated that a reasonable payback could be realized if hyperbaric filters were to replace the existing concentrate drying section."

Jan 1, 1992

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

?? Intro ?? Mass blast principle ?? LaRonde evolution toward mass blast ?? Overview ?? Mining method ?? Longitudinal ?? LaRonde evolution (2002 to today) ?? Drill and blast design ?? Consumptions and statistics ?? Mucking strategies ?? Case study ?? Examples ?? Conclusion ?? As underground mines extends to greater depths, few questions must be asked: ?? How to: keep operations safe eep operation effective reduce the cost maintain and control the dilution ?? Geomechanic method and practices; significant advances have been observed in the field of: ?? ground support ?? mining sequencing ?? Drilling and blasting; research and development has been less extensive, probably due to the following characteristics: ?? Drill and blast are mainly production-oriented ?? Drilling and blasting are more oriented toward productivity ?? Technology relies heavily on suppliers ?? Highly stressed ground conditions ?? generally help the explosives to break the rock for fragmentation ?? intensify over-breaks or blast-induced

Feb 1, 2008

By Francisco Gallo

La transformación de una empresa no solo depende de la capacidad de compromiso y cambio de la alta gerencia, sino se relaciona con la adopción de una tecnología iexitosa que transmita a la organización, un conjunto de paradigmas, procesos y política que el tiempo amerita. En este sentido, el presente trabajo describe el desarrollo de la tecnología informativa en la empresa minera Atacocha a través de las áreas de actividad productiva y administrativa. Para ello, es necesario que la empresa realice ajustes en su organización, procedimientos y políticas, de forma que se pueda aprovechar la inversión de una tecnología. Asimismo, los impulsores del cambio deben hacer el esfuerzo de identificar los medios por los que las premisas sobre las que se basa el cambio y la instrumentación de los mismos, permitan ser absorbidas gradualmente por la organización.

Sep 13, 2001

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971

By Bob Turnbull

The dictionary definition of calibration is: to determine by measurement or comparison with a standard, the corre c t value for each scale reading on a device.1 As a consultant or blast contractor, you assess risk every day. But, have you considered the importance of, and the risks associated with the calibration of your seismograph and the accuracy that is p rovided? Can your calibration pro v i d e r back you up in times of trouble and provide documented evidence that the equipment was functioning within specification? Can their calibration pro c e d u res withstand independent scrutiny and be shown to be traceable to a National Standards for accuracy of measurement? These are important documents that in court provide tremendous support that blasting and monitoring activities are conducted professionally and competently.

Jan 1, 2004

By Bill Williamson, Doug Richmond, Kerri Kuntz, Gus Gilman, Larry Heywood

This was a description by the poet of what occurred over two centuries earlier to Hannibal’s troops as he passed through the Alps. Interestingly, the pass that many feel is the route that Hannibal chose, Col de la Traversette, is the sight of possibly the earliest avalanche mitigation known. Monastery records describe a tunnel built in 1470, near the top of the pass designed to protect pilgrims from the upper slopes. For the next several centuries, avoidance and reinforced structures were the primary tactics to defend from avalanches

Jan 1, 2009

By P. S. G. Leon

One of the most difficult areas in concession contracts in resource-rich developing countries is achieving an equitable balance between the interests of investors, host states and, increasingly, mine and near mine communities. While some countries in the Andean region have resorted to outright or creeping expropriation of natural resource contracts under the guise of resource nationalism, others such as the Democratic Republic of the Congo (DRC), have claimed international best practice in the review (and setting aside) of important concession contracts.

Jan 1, 2011

By J. C. Edwards

The National Institute for Occupational Safety and Health (NIOSH) implemented a real-time neural network system which can discriminate mine fires from nuisance diesel emissions as part of an atmospheric mine monitoring system in NIOSH?s Safety Research Coal Mine. The real-time response of a neural network to fire sensor outputs was demonstrated for coal and belt combustion in the presence of diesel emissions. The fire sensors consisted of an optical path smoke sensor, a carbon monoxide (CO) sensor, and two types of metal oxide semiconductor (MOS) sensors. The real time neural network was trained with coal, wood, and belt fire experiments with and without diesel emissions background. The trained neural network successfully predicted mine fires with these combustibles in the smoldering stage prior to the onset of flames.

Jan 1, 2005

By Ronald E. Triplett, George K. Burke, Bernard H. Voor

To accommodate larger double-stack rail cars through a tunnel, the existing active tracks were to be lowered. The tunnel is an elliptical, horseshoe-shape with concrete base support, removal of which would jeopardize the tunnel integrity, particularly since the soils beneath part of the tunnel floor included soft, saturated silt overlying rock. Grouted bar anchors combined with a SuperJet soilcrete strut replaced the existing support in situ prior to floor lowering. Close cooperation and detailed timely engineering support provided a quality project. Project design and construction, ground improvement methods, and the performance of the work are described.

Jan 1, 2001

By Ricardo Burdisso, Rahul Kadam, Kyle Schwartz, Marty Johnson

Occupational exposure to hand transmitted vibration (HTV) arises from the hand held powered tools extensively used in the mining and construction industry such as rock drills, chipping hammers, chain saws etc. Regular exposure to HTV is the major cause of a range of permanent injuries to human hands and arms which are commonly referred to as hand-arm vibration syndrome (HAVS). In addition to this, the percussive tools generate overall sound power levels in excess of 110dBA in most cases. Such a high sound power level greatly exceeds the maximum permissible exposure limit (PEL) of organizations such as National Institute for Occupational Safety and Health (NIOSH) and the Occupational Safety and Health Administration (OSHA). Long term occupational exposure to this noise has been diagnosed as the main reason for permanent hearing loss in the operators. It is therefore important to develop an understanding of the mechanisms which lead to these high vibration and sound levels and in order to do this a detailed computational model of a pneumatic chipping hammer has been made. This paper presents a nonlinear computational model of a pneumatic chipping hammer. In order to better understand the dynamics of the chipping hammer, the hammer was subdivided into components that are shown in figure 1 (a) (based on a chipping hammer manufactured by Atlas-Copco). The hammer mainly consisted of a center body, a moving piston and a chisel. Compressed air is used to drive the piston inside of a cylinder and on the downward stroke this piston impacts the chisel to create the hammer effect. The machine has one pneumatic valve and this valve regulates the air supply either to the upper chamber or to the lower chamber. The valve changes according to the relative pressures in the two chambers and the supply pressure. There are also twelve different exhaust ports at two positions along the cylinder labeled upper ports and lower ports. As the piston moves the ports can be closed or open (allowing exhaust). Fundamentally, the computational model was made up of two different sub-models, a fluid model and a structural dynamic model as shown in Figure 3 (a) and (b) respectively. The first sub-model takes into consideration the fluid dynamics of the machine since the hammer is driven by compressed air. Equations for the mass flow rate though bleed orifices (assuming an isentropic process) 1 is used to determine the mass flow into and out of the upper and lower chambers. From this the pressures in the two chambers and consequently the forcing on the piston can be calculated. The second sub-model deals with modeling the structural [ ]

Jan 6, 2006

By M. D. Dolan

In this study, the development of a new method for investigating the diffusion of metal cations in multi-component slag systems, using microprobe analysis is discussed. This method allows the analysis of the diffusion of multiple species within a single system. This project has focused on the diffusion characteristics of manganese, iron, calcium and silicon in silicate slags, in order to simulate industrial steel and ferromanganese production. The diffusion behaviour of transition metals is of particular interest because of the effects of their variable valence. This study identified the variation in diffusivity of slag components with changes in composition and temperature of multi-component slag systems. The molecular structure of the experimental calcium-aluminosilicate slags was investigated to determine the chemical and physical properties that influence diffusion behaviour. This experimental data was used to develop predictive models for diffusivity. These models enable the estimation of the diffusivity of many slag components in complex slags, over a range of compositions.

Jan 1, 2004

By Jin Qiu

Experiments were performed to determine the extent of minor element elimination that occurred when mixtures of copper smelter dust and copper concentrate, were calcined under vacuum. Almost complete removal of the As, Sb, Bi and Pb occurred due to the conversion of the minor element compounds of these elements into their highly volatile sulphides by reaction with sulphur from the concentrate. Heat and mass balance calculations of the slag-blow in a copper converter found that ~30 tonnes of the vacuum calcine could be used to produce 100 tonnes of copper as white metal. The use of dirty concentrate as the sulphidizing agent in the vacuum calcination means that the minor element treatment capacity of the smelter complex could be increased by 60 %. Also the productivity of the converters may be increased by up to 8 % due to the supply of copper values and oxygen in the calcined mixture.

Jan 1, 2005