Search Documents

By A. Mazzucato

This paper presents the experimental results of driving and load tests on an instrumented pile driven into a test pit filled with fine homogeneous sand.

Jan 1, 2010

By Frederick C. Rhyner

This paper describes the design and construction of two high-capacity rock anchors to restrain a supplementary backstay for the Bear Mountain Bridge, which is a suspension bridge spanning the Hudson River about 40 miles north of New York City. The supplementary backstay was installed to relieve a portion of the tension in the southern main cable, which had been creeping in recent years. The two new rock anchors were 1,200 kip capacity each, installed at a batter to depths of 59 feet. This paper describes the subsurface investigation, group capacity analysis, installation and load testing. The rock anchors included strain gages connected to the monitoring system for the bridge. The paper describes the long term strain gage data which shows no change in stress distribution in either anchor.

Jan 1, 2010

By D T. Froedge

With successive generations of the Iso-Seismic System, we are acquiring more and more information about the actual behavior of blast induced ground, and airborne vibration, as it propagates through the environment. Some of the original “truths” that have been long accepted may have to be \revised.

Jan 1, 1995

Fully mechanized longwall mining with large mining heights (LMHs) in shallow-depth thick coal seams has been widely applied in Shenfu coalfield, China. Dynamic loading and rib spalling is serious when the LMH working face experiences periodic weighting in shallow coal seams. The advanced breaking position (fracturing ahead of the face) in the roof affects the strength of the mine pressure (weighting) when the roof is broken. Based on the theory of the “elastic foundation beam,” this paper presents a mechanical model for the advanced breaking of the roof, including a predictive formula. In an attempt to verify the formula, a field program consisting of multiple-point borehole extensometers installed in the roof in advance of the longwall face was performed in the No. 22201 working face of Zhangjiamao coal mine in the Shenfu mining area, China. The field measurement results show that the roof movement of the LMH working face is detected prior to roof pressure increase, and that the roof breaks approximately 5–8 m ahead of the face. This compares with a calculated value of 6.9 m, indicating that the formula developed in this research is reliable and should have application in predicting roof pressure associated with LMH working faces in shallow coal seams.

Jul 28, 2020

By M. Roy

Safety and stability of underground coal mine workings are always in danger when opencast mines are operating in close proximity. A study was conducted to investigate the level of vibration generated from opencast blasting at similar distances on the surface as well as in the nearby operating underground coal mine openings. Eight blasts were performed and nineteen vibration data were recorded on the surface behind the opencast blasting face and also in underground openings at similar distances. It was observed that magnitude of vibration recorded on the surface were more than those recorded in underground.

Jan 1, 2007

THREE regional meetings are planned for this summer and fall following the spring meeting held under the auspices of the Iron and Steel Committee and the Ohio Section at Cleveland in April and in lieu of a general fall meeting of the Institute. Plans for all of them are maturing rapidly. Excellent programs and. interesting visits to points of local tech¬nical interest are already assured. THE SALT LAKE CITY MEETING This meeting will be under the auspices of the Milling Committee and the Utah Section. It will be one of the features of the joint convention held the week of August 22 to 26 with the Western Division of the American Mining Congress. The Congress will be responsible for the general arrangements and for the program on the first day. The following general committees have been appointed:

Jan 7, 1927

By B. J. Buys

Rock bolt integrity is a critical issue for the mining industry because of its influence on the safety of mining operations. Guided ultrasonic wave testing of the defects associated with resin-anchored rock bolts was investigated. Axisymmetrical and three-dimensional finite element models were built, one of a partially encapsulated bolt and the other of a bolt with a simulated local corrosion crack. Experimental bolts were then installed in a testing block and typical responses were compared to finite element models of different defect scenarios. Encouraging results were obtained for the smaller axisymmetrical and three-dimensional finite element models, as well as during the experimental investigation. It is recommended that software with energy-absorbing elements should be utilized to consider higher frequencies and longer bolts. Once the integrity of models such as these has been established, the models could in principle be used to train neural networks for use in commercial equipment to determine the integrity of the installed bolt.

Jan 1, 2009

In this study, the flotation performances of ethoxycarbonyl thionocarbamate (ECTC), dialkyl thionocarbamate (DATC) and xanthate copper sulfide collectors are compared by the structure-reactivity relationship using generalized perturbation theory and density functional calculation at the B3PW91/6-31G(D) level. The electron-donating power of xanthates is strong and, therefore, xanthates can strongly react with metal cation on the surfaces of copper and iron sulfide minerals through the formation of normal covalent bonds. This explains the poor selectivity of xanthates and also the high pH levels (above 13) required for the flotation separation of copper/iron sulfide minerals. DATCs are more selective for copper sulfide flotation, particularly against gangue iron sulfides. Although less powerful than xanthates, DATCs can perform copper/iron flotation separation at lower operating pH (commonly at pH levels below 11.5). ECTCs use an ethoxycarbonyl replacing an alkyl N-substituent in DATCs. The presence of the ethoxycarbonyl group effectively changes the functional group of collector from -C(=S)NH- to -C(=S)NHC(=O)-. The strong electron-withdrawing ethoxycarbonyl group adjacent to the C=S group decreases the electron density of the sulfur atom, which improves ECTC?s selectivity against iron sulfide minerals at slightly alkaline conditions. The lowest unoccupied molecular orbit (LUMO) of ECTC, which is constituted by the pz-orbit of every atoms in the conjugate -O-C(=O)-N-C(=S)-O- group and which is pleased with accepting richly d-orbital electrons (feedback electrons) from the (t2g)6(eg)3Cu(II) or t6e4Cu(I) configuration of copper cation on the surfaces of copper sulfide minerals, resulted in the formation of dative p-bond. The iron atom, which has a (t2g)6Fe(II) or (t2ga)3(ega)2 Fe(III) configuration on the surfaces of iron sulfide minerals (Fe(III) is the predominant composition at alkaline conditions), has difficulty in offering its d-orbital electrons (feedback electrons) to ECTC?s LUMO. ECTC collectors are powerful for copper sulfide minerals and very selective against iron sulfides, which has been further confirmed by UV spectra and bench-scale and industrial-scale flotation tests.

Jan 1, 2008

Bortech’s BoreClad corrosion protection system will be displayed at MINExpo. BoreClad is an innovative system for inside diameter cladding of nozzles, tubes and other circumferential devices. Pressure vessels, mud pumps and other mining equipment must be protected from corrosive caustic chemicals. Usually manufactured from mild steel, they can be clad with a protective material, such as stainless steel, to provide corrosion resistance. However, most welding processes leave voids where corrosion can damage the base metal. BoreClad provides void-free welds by combining gas metal arc welding with automated feed and rotation of chuckable parts. Workpieces of up to 915-mm- (36-in.-) long with a 460-mm- (18-in.-)swing can be clad with stainless steel, Iconel or other exotic metals. In addition to eliminating the voids associated with hand welds, BoreCladcan lay more than 2.2 kg/h (5 lbs/hour) of metal. That is a significant reduction in weld time. Web sitewww.bortech.com.

Jan 1, 2004

By Luke Erickson

San Francisco Public Utilities Commission is planning to replace 5 miles of pipeline under San Francisco Bay. The tunnel will be constructed using an Earth Pressure Balance (EPB) TBM and will be the first TBM-driven tunnel under the Bay. The alignment passes under environmentally sensitive habitats, through interbedded layers of sands and clays, and through a buried bedrock ridge. This paper discusses the geotechnical characterization and anticipated tunneling conditions and presents the analysis of various construction methods that resulted in the selection of an EPB TBM. Considerations related to tunneling with an EPB TBM are described in detail, including ground conditioners, TBM cutterhead wear, muck control, and squeezing ground.

Jan 1, 2008

By Andrew Pontecorvo

The design of foundations for the tall buildings of lower Manhattan rely on the use of high capacity, rock anchors to resist overturning forces generated by lateral loads from wind, earth, water and, to a lesser degree, seismic forces. Once completed, the proposed towers at the World Trade Center (WTC) site will be among the tallest buildings in New York City. The towers are exposed to coastal winds and from several levels of below grade structure soil and water loads. The design loading required under the current New York City Building Code (NYCBC) is similar to the requirements of the building code used to design the original WTC Twin Towers. We will compare how rock anchors were deployed in the Twin Towers and how they are used in the new buildings. Changes to the building code are less significant that the changes to the design of the structure; that is how the outer skin or perimeter structure interacts with the building core. The result is a significant increase in the number of rock anchors required for the new buildings when compared to those installed in the original WTC Twin Towers.

Jan 1, 2011

By V. F. Parry

Subbituminous coal or lignite when stored in random riles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. Those changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.

Jan 1, 1941

By P. Bermingham

A new approach to load testing of high capacity piles is presented. The method is mobile, inexpensive, repeatable and non-destructive allowing for multiple pile testing at a single site. A reaction mass is placed over a pressure chamber situated atop the pile to be tested. The test method is significant in that it can produce linearly increasing forces of high magnitude (over 5.0 MN) with durations of up to 80 milliseconds. This represents pulse durations an order of magnitude longer than achieved using a drop hammer. The accelerations the pile undergoes are less than one g, (conventional dynamic methods = 50 to 100 g). These effects combine to produce pile behaviour no longer dominated by the action of stress wave, instead the pile is under high levels of stress through its length during the force input. This is representative of the situation when static loads are applied, thus the method may be considered quasi-static. Further advances introduced with this method are that pile deflection and transmitted force are measured directly by means of a laser beam and load cell. This allows accurate correlation of event load displacement histories without the error associated with zero shift (acceleration integration) or non-homogeneous materials (strain measurement). The load displacement histories emulate those obtained for static load testing.

Jan 1, 1989

By Roger L. Baer

Marine disposal of mill tailings has been practiced worldwide for over a century. However, only recently have the environmental effects of marine disposal been systematically studied. Some early attempts at marine disposal of tailings resulted in adverse impacts to marine life. However, recent advances in tailings disposal methods have included the introduction of engineered submarine tailings discharge systems, advanced environmental assessment and monitoring methods, and oceanographic modeling systems. Successful submarine tailings disposal (STD) has occurred at several mines. The U.S. Bureau of Mines (BOM) has undertaken studies of the disposal of mining and milling wastes in the marine environment. The BOM Alaska Field Operations Center, Juneau, initiated a review of the technology, regulations, and economic aspects of STD. The review illuminated the need for organization of literature on the subject, therefore the Bureau compiled this extensive bibliography on marine disposal of mill tailings. The bibliography presented here contains 1483 references and is also available through diskette in the Word Perfects format. A review of the references indicates that literature on submarine disposal inadequately covers the subject. The majority of the references listed only peripherally relate to the subject. Published literature on the engineering and environmental aspects of STD is severely limited.

Jan 1, 2011

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the' danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Harry Sutcliffe

THE PROBLEM Two and a half years have gone by since the December, 1976 Civil Engineering article on subway costs caused such a furore. What has happened in this interval? Even after discounting the crushing inflation rate, costs are still increasing, and there is no sign of a turndown, even in the rate of increase. Some steps outlined in the article have been taken. In April this year, the first D.O.T.-sponsored Peer Review Group, made up of managers of other transit properties, met in Boston to review MBTA's $500 million Red Line Extension-Northwest for cost effectiveness. While the impact of a review at the end of the design phase, with substantial segments under contract, cannot be as effective as a review early in the design phase, it is nevertheless a start. This first meeting will be followed by a review of Boston's Orange Line relocation, the final design for which is just underway. In the industry at large two facts are evident: 1. We are failing to reduce underground construction costs. 2. Underground construction is in danger of pricing itself out of the market place. It has always been a greater challenge to design a Chevvy than to design a Cadillac, but it is the Chevvy we need today. Much attention has been focussed in the past on engineering design in the narrow sense: areas such as ground loading conditions and concrete design. This paper will attempt to make the case that costs in urban underground construction are primarily outside the area of structural

Jan 1, 1979

By John Lindsay

Outline ??Recovery plant requirements and concepts ??Common recovery plant unit processes ??Recovery plant design considerations ??Peripheral issues Process Design ??Liberation ??Separation ??Recovery Processing ??Density 3.5 g/cm3 ??Luminescent under x-ray ??Hydrophobic (non wettable) surface ??Non-magnetic ??Inert to strong acids / bases

Apr 1, 2005

By R. H. Grau, S. B. Robertson, R. B. Krog

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. Large-opening mine ventilation is unique for the following reasons: (1) it is challenging to keep airflow velocities high enough to effectively remove or dilute airborne contaminants, (2) large air volumes can be moved through the mines with little static pressure drop, and (3) stoppings to direct ventilation airflows are costly to construct and maintain. The research results suggest that by incorporating ventilation planning into the mine planning process, using propeller fans, developing new stopping materials and construction methods, and using long pillars to eliminate crosscuts where possible, the ventilation of large-opening mines can be significantly improved. The ventilation improvements created by incorporating these various techniques into the ventilation plan will help reduce the exposure of mine workers to airborne contaminants in underground large-opening mines.

By Rimas Pakalnis

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining is generally necessary either due to a weak rock mass comprising the immediate back and/or high induced back stresses. A major concern in the design of sill mats is the loading and strengths associated with the overlying sill mat. This paper reviews past practice coupled with present observations and measurements from over ten(10) mines throughout North America. It outlines areas of concern in terms of design requirements.

Apr 1, 2005