Search Documents

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008 ? ?I guess that without the occasional complaint, your mine is probably over-ventilated? (Marks, 2008). Miners are seldom in this situation and often spend much of the time trying to find enough air to keep the operation running. With examination there are some things that can be done to make the best use of ventilation systems. Should there be surplus air, in which some of these options may result - financial and other benefits can be obtained. Some of the issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and non-metal mines. Also, operations are faced with demands from reserves that are deeper, hotter and further away from fans and shafts, not to mention increased production demands. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Most of the options presented in this paper are useful for metal non-metal operations but some may be applicable to coal too. OPTIONS FOR IMPROVEMENT Some of the areas to be addressed are shop ventilation methods, auxiliary equipment areas, dedicated intakes and returns, optimizing development, examination of mine airway utilization and alternative ventilation methods. UNDERGROUND SHOPS First, examine what is being done with the underground shop air. If it is being coursed directly to the returns there may be some potential to better utilize this, in most cases, relatively contaminant free air. Research the legal options for ventilating mine shops. MSHA regulations in 30CFR 57.4761 (1) allow the following options: To confine or prevent the spread of toxic gases from a fire originating in an underground shop where maintenance work is routinely done on mobile equipment, one of the following measures shall be taken: use of control doors or bulkheads, routing of the mine shop air directly to an exhaust system, reversal of mechanical ventilation, or use of an automatic fire suppression system in conjunction with an alternate escape route. The alternative used shall at all times provide at least the same degree of safety as control doors or bulkheads. Discussion This regulation gives some operators flexibility in ventilating underground shop facilities. If shop air is to be coursed through the work area, and then directly to the mine return, the question should be asked ? is the quality of air good enough to be reused in the mine, and if so, what are the risks? Can the risks be accommodated and managed to accomplish the change? If so, a considerable increase in mine level airflow could be attained by reusing shop air. Clearly, regulations are a minimum standard, and can be exceeded. Metal non-metal mine regulations are not as specific as coal due to the multitude of different mining methods and conditions utilized. Risks must be thoroughly examined and addressed to assure a safe environment. Issues Determine what contaminants are being produced in the work area ? welding fumes, diesel exhaust, paint fumes, chemicals and solvents, etc. Survey the area and determine exposures. MSHA requires exposure monitoring in 30 CFR 57.5002 (1) of dust, gasses mists and fumes to assure air quality is being met. Perform surveys and examine existing data to quantify personal and area concentrations of contaminants. Often there is adequate circulation such that exposure levels in shop work areas are low. After sending shop air back into the system any contaminants would be further lowered by dilution with other mine intake air downstream. Look at the shop work schedule. If only on day shift, the other two shifts and possibly weekends have no activity or source of contamination to affect the ventilation system. The worst case planning scenario would be a shop fire. Study and simulate how this would affect the mine and shop area. MSHA regulations require an escape route and a fire suppression system be installed and maintained as follows in 30 CFR 57.4671 (1): (d) Automatic fire suppression system and escape route. If used as an alternative, the automatic fire suppression system and alternate escape route shall meet the following requirements: (1) The suppression system shall be? (d)(1)(i) Located in the shop area; (d)(1)(ii) The appropriate size and type for the particular fire hazards involved; and (d)(1)(iii) Inspected at weekly intervals and properly maintained. (2) The escape route shall bypass the shop area so that the route will not be affected by a fire in the shop area. Case Study In an underground room and pillar mine, active mine workings were advancing further away from the mine shaft with deteriorated returns and leakage having a negative effect on ventilation airflows to the face. Mine level airflows were 236 m3/s (500,000 cfm) and shop airflows were 24 m3/s (50,000 cfm) (see Figure 1A). No additional capacity was available at the main surface fan. A solution was to utilize the shop air then send it to the mine areas instead of directly to the return. Considerable information on shop air quality and exposures from many years of operation was examined and no negative data was discovered. A risk analysis determined that moving forward with a shop air reuse program was desirable. A plan was developed, analyzed and decision to proceed approved by mine management. The change was simulated on the computer with the USBM/MTU MFire program before being implemented. This included utilizing fire scenarios to examine potential exposures to inby mining sections and plan escape routes. A monitoring system was designed and installed in cooperation with the US Bureau of Mines to monitor carbon monoxide

Jan 1, 2009

By Dhananjaya Senapati, E. V. S. Uma Maheswar, C. R. Ray

Carbothermic process of Ferro Silicon production is primarily a slag-less process. However, slag formation is observed in the regular operation as experienced by almost all the Ferro Silicon Producers in different pro-portions. The problem of slagging in the furnaces may be due to: a)Variation in the input burden charge material quality b)Fluctuations in the Carbon balance and/or c)Fluctuations in the Electrode penetrations The problem will be more severe in nature with the increase of the size of the furnace. The operation performance of the furnace gets badly affected if the slag formed in the furnace is not removed from the bath in time and to the maximum extent possible. It is, therefore, very essential to know the characteristics of the slag formed in the Ferro Silicon Furnaces, besides eliminating the very cause of formation itself; and to find the routes of draining of the same from the furnace bath effectively. This paper envisages the effects of using the LIME STONE in the Ferro Silicon Burden in stabilizing the 48MVA Furnace for improved performance and better consistency. Quality fluctuations in the available Raw Materials are compared with that of the requirements for the Ferro Silicon production. The furnace operational data is compared for 12 months period each for the period corresponding to the before and after usage of lime stone in the burden and found encouraging results in the performance. Implications of use of Lime Stone in the burden on the quality of the output alloy are also studied.

Jan 1, 2007

This paper reviews recent positive developments in Europe on the regulation of gold mining. However, it also examines the problem that while gold projects may be bankable and technically and environmental defensible, the odds tend to be stacked against granting of an environmental permit. The historic background to this situation is examined and current developments and initiatives are critically analysed. Standards and benchmarks for the industry have been established across the community and these have a strong influence in European Union accession (and aspiring) states as well. While this is welcome in regard to improving environmental performance, it also represents a significant milestone with mining (and particularly gold mining) now æon the mapÆ as a legitimate enterprise, a situation that was patently not the case prior to 2003. At the project level, very frequently, the difficult biophysical problems are addressed and satisfactorily dealt with according to the new regulations, but still there are problems regards trust and acceptance that underpin a æsocial licenceÆ. What goes wrong and how can companies deal with the social/environmental issues that lead to entrenched views and concerns, irrespective of any amount of demonstration of good practice and corporate social responsibility? What is the role of the non-governmental organisation (NGO) and are they as accountable and responsible as they should be? The findings presented draw upon recent experience with the environmental permitting of projects in Spain, Greece, Romania, Bulgaria and Serbia on behalf of Australian, Canadian and British companies as well as international funding institutions.

Jan 1, 2007

By C. Y. Liu

This paper principally deals with the application of caisson foundation in the Chinese bridge building industry, the different types of caisson foundation adopted, and their spheres of application. Caisson foundation has been used and speedily developed for bridge works in New China, and a number of new innovations have been made in its design. Especially in deep water foundation, the Nanjing Bridge over Changjiang has attained one of the deepest bridge foundations in the world. There are six types of deep caisson foundation being now in use in China, namely:

Jan 1, 2010

By Yuemin Zhao, Daniel Tao, Xinxi Zhang, Qingru Chen, Maoming Fan, Zhenfu Luo, Xiuxiang Tao, Guohua Yang

Coal is currently cleaned with the minimum of size reduction, fine particle processing, recovery, and tailings disposal are major problems. Adequate water resources are not always available. For example, two thirds of China's coal is located in arid areas. Hence, dry separation provides an alternative approach. Of the dry coal separation methods available, air dense-medium fluidized beds have been used to separate 50~6mm coal efficiently. However, excessive bubbling and back mixing of the separated solids in the air-dense media fluidized bed causes the high lower size limit of 6mm for the feed material, this affecting the preparation efficiency. Based on prior study on air-fluidized dense media for 6~50mm coal preparation, this paper presents methods and test results on the fine coal dry classification, static electricity beneficiation of 0~0.5mm coal, and magnetically stabilized fluidized beds for separating 0.5~6mm coal.

Jan 1, 2005

By R. H. Grau, S. B. Robertson, J. Dolgos, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has developed a computer program called the Air Quantity Estimator (AQE). The purpose of the program is to provide a starting point for estimating the air quantity needed to dilute diesel particulate matter (DPM) in an underground large opening mine, albeit taking into account various input assumptions. The AQE estimates the total air quantity needed to dilute DPM emissions that enter the main airstream of the mine to current statutory levels. It helps operators pinpoint vehicles that are high DPM contributors. In addition, it allows the user to make “what if” scenarios by varying the input parameters to achieve the most efficient and practical ventilation system. The AQE is a stand-alone software program that does not require any type of spreadsheet software. Engine data must be known or estimated with some accuracy and assumptions must be made in order to limit the variability of the program output. Program calculations and two case studies, for validation purposes, are included in this report. It should be noted that the program does not ensure adequate face ventilation and personal exposure compliance.

Constraints on the mineral industry are best treated as issues that have to be understood and managed in partnership rather than in conflict with communities. TheZapopan development at Mt Todd in Australia and the Martha Hill development at Waihi in New Zealand are but two of many recent successful examples at the local level.   However, at the national level, the issues are more complex and more difficult to resolve because the most influential stakeholders are now the urban electorates and governments defer to their perceptions when making decisions and policy. In the developed countries, government policies for the development of mineral resources have been progressively eroded since the early 1970s. At the same time policies for the environment and for native land rights have generally been carried out in a way that has reduced access to minerals and increased the cost and risks for prospectors and developers (Hancock, 1995). Since the end of the Cold War, the lesser developed countries (LDCs) have introduced policies to attract investment in their mineral resources that remained undeveloped under previous unstable or hostile regimes. The increased attraction of these LDCs and the decreased attraction of the developed countries has caused many Australian and North American companies to outlay increasing proportions of their budgets and capital investment in the LDCs.   Significantly, LDC policies for environment protection do not discourage exploration and mine development, Surveys of the relative appeal of the LDCs and the traditional mining countries of the developed world, rate Chile, Argentina and Indonesia ahead of Australia and Canada in terms of risk, delays and ease of doing business (Australian Mining Monthly, February 1994).

Jan 1, 1995

By Brad Simser

The Brunswick No. 12 Mine is a 10 000 tonne per day producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400m and 1200m below surface. The combination of a high overall extraction ratio and high horizontal stresses (twice the vertical) has elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning. Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues towards mining in deeper, higher stress environments (e.g. South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically.

May 1, 2003

By K. Osburn

South Deep Gold Mine, owned by Gold Fields Ltd., is situated near Westonaria in the Gauteng Province of South Africa and mines the conglomerate bands of the Upper Elsburg reefs (Mondeor Conglomerate Formation) of the Witwatersrand Supergroup and the Ventersdorp Contact Reef (VCR) of the Ventersdorp Supergroup. The stoping and underground developments are mechanized. The Upper Elsburg reefs are mined by a variety of mining methods, including mechanized drift and fill, modified drift and bench, longhole stoping, and low-profile mining. Optimal mine design and scheduling for deep-level mechanized mining are complex, and success is highly dependent on detailed, robust, and accurate geological and geostatistical models. Geological structures significantly influence the sedimentological characteristics, distribution, and preservation of the Upper Elsburg reefs and VCR. Accordingly, particular emphasis is placed on the generation of a mine-scale structural model that accommodates the relationships between the older north-trending fault systems (West Rand and Panvlakte faults) and younger east-trending dextral wrench faults. Results from underground mapping, borehole intersections, and highresolution three-dimensional seismic data have been integrated to produce coherent three-dimensional geological models. The Upper Elsburg reefs suboutcrop against the VCR and comprise an easterly diverging clastic wedge, thickening from the suboutcrop position, to approximately 130 m at the mine?s eastern boundary. The Upper Elsburg reefs are characterized by conglomerate and quartzite bands forming multiple, stacked, upward-fining unconformity-bounded couplets. Palaeocurrent directions are dominantly from west-northwest to east-southeast, indicating that the more proximal deposits are preserved close to the suboutcrop, with distal facies to the east. Sedimentological modelling is applied to individual stratigraphic units and caters for facies definition. This is achieved through channel width (CW) kriging and fitting of type sections to borehole and mapping data. Homogenous geological geozones for each stratigraphic unit are thus defined within individual structural blocks on the basis of those sedimentological parameters that have been found to have a positive spatial correlation to gold concentration. These geozones then serve as constraints to the evaluation of the orebody. This contribution presents a summary of the modelling processes that are currently applied in the development of high-confidence, timeously produced geological models that are essential input for mineral resource estimation and mechanized mine planning and scheduling.

Jan 1, 2014

By M. M. Gadde

Recent regulatory changes in the United States make it mandatory to conduct structural analysis of coal mine seals used to isolate abandoned workings from active mining areas. Different loading criteria are available for seal design depending on whether gob composition is actively monitored and maintained or not and whether the gob conditions lead to deflagration or detonation type loading. Since the loads involved in seal designs are dynamic in nature, the structural analysis must be made using dynamic stress analysis techniques. However, because of the significant complexities involved in conducting dynamic analyses, some designers use approximate simplified techniques to address the design problem. In this paper two such simplified methods are critically evaluated for their suitability to design coal mine seals. The benefits and limitations of the simplified methods are also outlined. Some comparisons are made to show the differences between sophisticated three dimensional dynamic analyses and the simplified methods and to delineate the problems associated with the latter approaches.

Jan 1, 2009

By Mostafa Mossaad, Ali Helwa, Manal Salem

Support of excavation (SOE) design practice tends to model SOE elements using two-dimensional (2D) analyses to avoid the complexity associated with three-dimensional (3D) analyses. Such practice overlooks soil arching in the horizontal plane and prevents designers from accounting for elements such as capping beams as part of the statical system. This study simulates square excavations supported by cantilever slurry walls in dry cohesionless soil using 2D and 3D finite element (FE) models. First, side support wall behavior is compared from 2D and 3D FE models for variable excavation length to depth (L/H) ratios. Second, the effect of slurry wall lateral bending stiffness on wall behavior is studied by modeling the wall using plate element with isotropic and anisotropic wall stiffness. Finally, the sensitivity of cantilever wall behavior to the presence of capping beam is illustrated. The study concludes that unbraced excavations with L/H ratios greater than 5 almost resemble plane-strain conditions. Slurry walls are better simulated in 3D FE models by dividing the plate element into discrete panels or by assigning anisotropic bending stiffness to the plate element. Finally, the presence of capping beam affects the behavior of cantilever walls resulting in reduction of deflections and redistribution of bending moments. INTRODCUTION Support of excavation (SOE) design practice ranges in complexity from conducting simple hand calculations to performing three dimensional numerical modeling depending on several factors among which is the geometry of the design problem. This paper addresses walls that are designed using numerical modeling, and discusses the factors governing the choice of the most suitable modeling approach. It has been believed for a while that modeling excavations using 2D numerical models would lead to a more conservative solution, which turned out to be incorrect in specific cases. This paper attempts to describe cases where 2D finite element modeling could be on the conservative side and other cases where it could be less conservative than the more complex 3D modeling.

Jan 1, 2018

Development of Grindability Tests Based on Direct Measurement of Energy Nowadays, for the characterisation of the grindability different grindability indices - Bond-work index (Wi), Hardgrove Grindability Index (HGI) or Zeisel specific grindability (Wt) - are used. Generally, the grindability tests are carried out under relatively simplified circumstances, in a special dry batch mill with defined feed size material until prescribed conditions are reached at room temperature. However, in the fine- and ultra fine grinding, which is a frequent task (fly ash, tailings, alumina, etc), a fine material (<50 - 200 ¦m) is usually ground down to the few micrometers. The conventional grindability testing methods and apparatuses (Bond-, Hardgrove-, Zeisel-processes) for their determination, although, are not suitable directly to measure the grindability of such fine materials, since the maximal particle size of the feed material (0.5 - 3 mm) to be tested is much higher. One of the important goals of the research carried out in our Institute was to develop the novel grindability testing methods, which are suitable for the fine and ultra fine grinding, and additionally provide the possibility for the fast determination of the grindability. In order to realise the above aim the conventional Bond- and Hardgrove- mills were modified in order to directly measure the grinding work. In particular, the Hardgrove-mill was equipped with a simple torque-meter (load cell). The Bond-mill was rigged with a digital electric power measurer. The systematic experiments were carried out parallel in both mills using the conventional and the developed methods. Finally the results of both were compared. The measuring results have proved that the Bond-work index can be determined based on the developed methods. The new grindability testing methods were applied successfully in several industrial research tasks for the determination of the specific grinding energy and the Bond-work index. These methods can be also used in the industrial practice for the control of the grinding process.

Sep 13, 2010

By H. J. Heinen

This Bureau of Mines report reviews the recent developments in the heap leaching of gold ores with dilute cyanide solutions and the recovery of gold and associated silver from the pregnant effluents by a carbon adsorption-desorption method. Mineralogical considerations, experimental work, field studies, and commercial operations are described. Also presented are recent process advances developed by the Bureau, including the application of (1) alcohol additives to the conventional hot alkaline cyanide strip solution to enhance gold desorption from precious metal-laden activated carbon, and (2) Na2S precipitation of the silver from geld-silver cyanide solutions as a means of reducing the inventory of carbon required for precious-metal adsorption from heap leach effluents and for the production of low-silver bullion from activated carbon stripping solutions.

Jan 1, 1978

?Classification System Efficiency (CSE)? is a simple, powerful concept which can be used to measure and improve ball mill circuit efficiency. This paper describes six plant case studies which demonstrate the use of CSE to diagnose and/or improve grinding circuit performance, with related improvements in circuit efficiency ranging from 3 to 30 percent. The increased effective mill grinding energy is recaptured from energy that was going into over grinding, which can greatly benefit downstream mineral separation. The achievable CSE for given circuit design/operating variables is described, providing every plant metallurgist with the means to determine the potential for increasing their particular grinding circuit?s efficiency through increased CSE.

Jan 1, 2012

By S. Jiansheng, H. Nakayama, D. Lu, A. Wang

ABSTRACT: New techniques and methods for 3D geo-mechanical model test are presented in this paper. The new model material NIOS with high density and low cost; the so-called DPSS (Discrete Principal Stress Surface) loading concept, the loading and monitoring system for the generation of the 3D initial stress field of the model test, also the special techniques and apparatuses for modelling the excavation of caverns located deep inside the model material, are developed and introduced. By adopting those new techniques, a very large 3D geo-mechanical model test with high comparability for a newly designed underground powerhouse has been successfully fulfilled. Key Words: 3D model test, underground group caverns, excavation process modeling. ZUSAMMENFASSUNG: Neue Techniken und Methoden für 3D geomechanischen Modellversuch wurden in diesem Artikel vorgestellt. Ein neues Modellmaterial mit hocher Dichte und niedrigem Preis, ein sogenanntes DPSS (Discrete principal stress surface) Ladenkonzept, ein Laden- und Überwachungssystem für die Erzeugung des 3D primären Spannungsfelds und überdies spezielle Techniken und Maschinen für das Ausbruch der tief in dem Versuchsmodell liegenden Kaverne wurden entwickelt. Bei Anwendungen dieser neuen entwickelten Techniken wurde ein sehr großer 3D Modellversuch mit großem Maßstab für ein geplantes unterirdisches Kraftwerk erfolgreich durchgeführt. Stichworte: 3D Modellversuch, unterirdischen Gruppekaverne, Ausbruchsmodellierung Résumé: le test de modèl de Nouvelles techniques et méthodes pour la géo-mécanique 3D est figuré dans ce papier. Le nouveau modèle de matériels NIOS avec la haute densité et le coût bas; la conception proposée de chargement DPSS (Discrete Principal Stress Surface), le système de chargement et de moniteur pour la génération de champs de stress initial du test de modèle, ainsi que les techniques et appareils spéciaux pour modeler les excavations de cavernes profondément localisées dans l’intérieur du matériel de modèle, sont développés et introduits. A travers l’adoptation de ces nouveaux techniques, le test de modèle de la géo-mécanique très large 3D avec la haute comparabilité pour actualiser une nouvelle étude de la centrale électrique sous-terraine a déjà accompli avec succès. Mots de clé: test de modèle 3D, groupes de cavernes sous-terraines, processus de modèle d’excavation

Jan 1, 2003

By Francis T. Freeland

In the West many precious-metal mines are worked in patches by lessees, under conditions which closely resemble those of what is called " tribute-work" in Cornwall.* The company has its own foreman or inspector, and usually employs the engineman, blacksmith, pumpman, and perhaps other general workmen. As an inducement to work on a new piece of ground, where no ore is in sight, the company may advance a " footage"

Jan 1, 1896

Exploring the Breakage Environment in Mills with Discrete Element Methods

Sep 13, 2010

Despite the wealth of information available on phase equilibria of oxide systems there remainmany gaps and inconsistencies in our knowledge base. From an industry perspective there is anongoing need to adequately describe the phase chemistry of slag systems in order to optimizeprocess performance and improve productivity. Since this chemical behaviour cannot be predictedfrom first principles it follows there is also an ongoing need for accurate experimental data. The advances made in recent years in the capabilities of sophisticated analytical and measurement equipment have made it possible to develop new experimental techniques for the direct determination of phase equilibria in low order and complex multi-component slag systems. In addition the development of powerful computer modelling tools makes it possible to provide more comprehensive descriptions of the phase chemistry, to present the information in a range of perspectives, and to critically analyse the various types of related thermodynamic and structural information available. This review provides an overview of the types of information that can be used to determine phase equilibria in slags systems, analyses the influence of uncertainty and the relative importance of these types of data, and describes the advantages and limitations of the various experimental techniques that can be employed to obtain this information. Examples of recent studies are provided that demonstrate how an integrated approach to the determination of phase equilibria in complex systems, involving the use of targeted experimental studies and systematic thermodynamic model development, can lead to a better utilization of our current research capabilities and resources and more accurate descriptions of these systems. Keywords: slags, phase equilibria, experimental techniques

Jan 1, 2004

By David Schlain

The Bureau of Mines investigated methods for electrodepositing platinum-group metals from molten cyanide baths. The preparation of thick, protective coatings on molybdenum, Inconel, graphite, stainless steel, copper, and other structural metals were studied, as well as the electroforming of platinum and iridium crucibles. Iridium, rhodium, and ruthenium can be electrodeposited under an inert atmosphere, while platinum and palladium require the presence of air. Electrolytes may be prepared by direct-current electrolysis in NaCN or mixtures of NaCN and KCN using anodes of the particular platinum-group metal. When the concentration of metal increases to about 0.3 or 0.4 percent, the deposits become bright, adherent, and coherent. Current densities may be 10 to 25 ma/cm2, and plating rates are often 0.5 mil/hr. Platinum and palladium baths deteriorate because of the oxidation of cyanide to cyanate and carbonate, and the precipitation of metal. Changes in the platinum cyanide bath are relatively slow. The protection against oxidation afforded by the platinum-group metal coatings is evaluated by testing encapsulated specimens in a thermogravimetric balance. Surface pretreatment and the use of undercoats are discussed.

Jan 1, 1977

By Kevin Phelps, Jason Baird

When dealing with high velocity projectiles, the ability for researchers to accurately and precisely measure the velocity of the projectile is of great value. This report will analyze three different methods of recording high velocity projectiles for: their ability to record velocity data, pros and cons for each method, and any possible bias or limitations that would result. Method 1 uses a Phantom V10 high-speed video camera and a velocity reference screen to record the projectile’s path and proprietary Phantom software to analyze the data and determine velocity. Method 2 utilizes two break screens. This method, consisting of strung copper wire as the break material, is one that has been used in the past by Missouri University of Science and Technology (MS&T) researchers in assisting in finding velocities of high-speed projectiles. Method 3 is a pair of make screens, similar to Method 2 in that two screens were used for each test but relies on a projectile making a circuit between two sheets of metal separated by an insulation layer, to find a velocity. All three methods will be used simultaneously in each shot to rule out any projectile differences in subsequent shots. Projectiles of three different relative velocities, low, medium, and high, will be fired and analyzed to determine strengths and weaknesses of each method.

Jan 1, 2014